HWMUSA-SHDSL-CPE-MIB

All MIBs › HWMUSA-SHDSL-CPE-MIB

Category: DSL and Broadband, Vendor: Huawei

Description: Huawei MUSA MIB for SHDSL customer premises equipment (CPE) management including line status and performance counters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HWMUSA-SHDSL-CPE-MIB?

HWMUSA-SHDSL-CPE-MIB is a Huawei Technologies (North America) proprietary MIB reporting inventory and configuration for SHDSL CPE devices. Its objects cover a common-inventory table (model, software/hardware version, device name), a common-config table (date, time), a common-action table (database-save, warm-start actions), an SNMP-config table (IP address/subnet mask/gateway, two trap-destination IP/port pairs), and an SDSL-specific configuration table. As a configuration/status MIB it lets an administrator confirm firmware/hardware version and SNMP trap-destination configuration on a Huawei SHDSL CPE. It is deployed on Huawei Technologies SHDSL CPE devices. Engineers can download the HWMUSA-SHDSL-CPE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HWMUSA-SHDSL-CPE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei Technologies SHDSL CPE devices

Monitoring Examples

An administrator checks umCommonInventorySwVer and umCommonSnmpConfigTrapIpAddress1 to confirm firmware version and trap destination on a Huawei SHDSL CPE.

What Can Be Monitored

device inventory and SNMP trap-destination configuration

Imported Objects

From HUAWEI-MIB

hwProducts

OBJECT-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From RFC1213-MIB

DisplayString

From SNMPv2-SMI

Gauge32
IpAddress
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
musa	1.3.6.1.4.1.2011.2.6
ias	1.3.6.1.4.1.2011.2.6.7
hwIasService	1.3.6.1.4.1.2011.2.6.7.4
hwMusaShdsl	1.3.6.1.4.1.2011.2.6.7.4.4
hwShdslCPE	1.3.6.1.4.1.2011.2.6.7.4.4.2
hwShdslCPECommon	1.3.6.1.4.1.2011.2.6.7.4.4.2.1
umCommonInventoryTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.1		not-accessible	A table containing common inventory information.
umCommonInventoryEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.1.1		not-accessible	An entry in umCommonInventoryTable.
INT umCommonInventoryModel	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.1.1.1	INTEGER	read-only	This variable indicates the model number.
STR umCommonInventorySwVer	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.1.1.2	DisplayString	read-only	This variable indicates the software version. format: a.bcd (a, b, c, d: 0 ~ 9)
STR umCommonInventoryHwVer	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.1.1.3	DisplayString	read-only	This variable indicates the hardware version. format: a.bcd (a, b, c, d: 0 ~ 9)
STR umCommonInventoryDevName	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.1.1.4	DisplayString	read-write	This variable indicates the device name.
umCommonConfigTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.2		not-accessible	A table containing common config information.
umCommonConfigEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.2.1		not-accessible	An entry in umCommonConfigTable.
STR umCommonConfigDate	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.2.1.1	DisplayString	read-write	This variable is used to define date information of the device. The format is MM/DD/YYYY. MM means month, DD is day, and YYYY stands for year. The range is from 01/01/1990 to 12/31/2100.
STR umCommonConfigTime	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.2.1.2	DisplayString	read-write	This variable is used to define time information of the device. The format is HH:MM:SS. HH means hour, MM is to indicate minute and SS is for second.
umCommonActionTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.3		not-accessible	A table containing actions to CPE.
umCommonActionEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.3.1		not-accessible	An entry in umCommonActionTable.
INT umCommonActionDbSave	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.3.1.1	INTEGER	read-write	This variable is to initiate the VCDB command. 1: save
INT umCommonActionWarmStart	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.3.1.2	INTEGER	read-write	This value is to restart the device. TRUE (1): warm start
umCommonSnmpConfigTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.4		not-accessible	A table containing SNMP configuration information.
umCommonSnmpConfigEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.4.1		not-accessible	An entry in umCommonSnmpConfigTable.
IP umCommonSnmpConfigIpAddress	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.4.1.1	IpAddress	read-only	This variable is to indicate IP address of the device.
IP umCommonSnmpConfigIpSubnetMask	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.4.1.2	IpAddress	read-only	This variable is to define the subnet mask of the IP address of the device.
IP umCommonSnmpConfigIpGatewayIp	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.4.1.3	IpAddress	read-only	This variable is to define the gateway IP address of the device.
IP umCommonSnmpConfigTrapIpAddress1	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.4.1.4	IpAddress	read-only	This variable is to define the IP address where the manager receives trap.
INT umCommonSnmpConfigTrapIpPortNum1	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.4.1.5	INTEGER	read-only	This variable is to define the UDP port number where the manager receives trap. The possible values are: 162 (default) 62000 62001 62002
IP umCommonSnmpConfigTrapIpAddress2	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.4.1.6	IpAddress	read-only	This variable is to define the IP address where the manager receives trap.
INT umCommonSnmpConfigTrapIpPortNum2	1.3.6.1.4.1.2011.2.6.7.4.4.2.1.4.1.7	INTEGER	read-only	This variable is to define the UDP port number where the manager receives trap. The possible values are: 162 (default) 62000 62001 62002
hwShdslCPESdsl	1.3.6.1.4.1.2011.2.6.7.4.4.2.2
umSdslConfigTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.1		not-accessible	A table containing Sdsl configuration information.
umSdslConfigEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.1.1		not-accessible	An entry in umSdslConfigTable.
INT umSdslConfigNEType	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.1.1.1	INTEGER	read-only	This variable is to set this STU-C or STU-R configuration. (0): STU-C (LT mode) (1): STU-R (NT mode)
INT umSdslConfigRateAdaptive	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.1.1.2	INTEGER	read-write	This variable is to enable/disable the rate adaptive configuration. (0): Fixed (1): Adaptive
INT umSdslConfigDataRate	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.1.1.3	INTEGER	read-only	This variable is to set data rate (N*64k) of Sdsl. If Rate Adaptive is TRUE, the value is invalid till Rate Adaptive is FALSE.
INT umSdslResetPerformance	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.1.1.4	INTEGER	read-write	This value is to reset performance register. 1: reset all current performance data 2: reset current ES 3: reset current SES 4: reset current UAS 5: reset all history performance data 6: reset history ES 7: reset history SES 8: reset history UAS
INT umSdslTimeElapsed	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.1.1.5	INTEGER	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period.
INT umSdslValidIntervals	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.1.1.6	INTEGER	read-only	The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online.
umSdslThresholdTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.2		not-accessible	A table containing MSDSL configuration information.
umSdslThresholdEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.2.1		not-accessible	An entry in umSdslThresholdTable.
G32 umSdslThreshold15mES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.2.1.1	Gauge32	read-write	This variable defines the 15-minute threshold of ES.
G32 umSdslThreshold15mSES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.2.1.2	Gauge32	read-write	This variable defines the 15-minute threshold of SES.
G32 umSdslThreshold15mUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.2.1.3	Gauge32	read-write	This variable defines the 15-minute threshold of UAS.
G32 umSdslThreshold24hES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.2.1.4	Gauge32	read-write	This variable defines the 24-hour threshold of ES.
G32 umSdslThreshold24hSES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.2.1.5	Gauge32	read-write	This variable defines the 24-hour threshold of SES.
G32 umSdslThreshold24hUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.2.1.6	Gauge32	read-write	This variable defines the 24-hour threshold of UAS.
G32 umSdslThresholdSNRMargin	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.2.1.7	Gauge32	read-write	This variable indicates the SNR margin threshold of the Sdsl line. 1~15: valid value
G32 umSdslThresholdLoopAttenuation	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.2.1.8	Gauge32	read-write	This variable indicates the Loop Attenuation threshold of the Sdsl line. 1~127:
umSdslPmCurrentTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.3		not-accessible	The Sdsl PM Current table.
umSdslPmCurrentEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.3.1		not-accessible	An entry in the Sdsl Pm Current table.
G32 umSdslPmCurrentES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.3.1.1	Gauge32	read-only	The number of Errored Seconds encountered by an Sdsl during the current interval.
G32 umSdslPmCurrentSES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.3.1.2	Gauge32	read-only	The number of Severely Errored Seconds encountered by an Sdsl during the current interval.
G32 umSdslPmCurrentUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.3.1.3	Gauge32	read-only	The number of Unavailable Seconds encountered by an Sdsl during the current interval.
umSdslPmIntervalTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.4		not-accessible	The Sdsl Interval table.
umSdslPmIntervalEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.4.1		not-accessible	An entry in the Sdsl Interval table.
INT umSdslPmIntervalIndex	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.4.1.1	INTEGER	not-accessible	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval.
G32 umSdslPmIntervalES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.4.1.2	Gauge32	read-only	The number of Errored Seconds encountered by an Sdsl in one interval.
G32 umSdslPmIntervalSES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.4.1.3	Gauge32	read-only	The number of Severely Errored Seconds encountered by an Sdsl in one interval.
G32 umSdslPmIntervalUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.4.1.4	Gauge32	read-only	The number of Unavailable Seconds encountered by an Sdsl in one interval.
umSdslPmCurrentDayTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.5		not-accessible	The Sdsl PM Current Day table. (0:00AM ~ the last completed quarter)
umSdslPmCurrentDayEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.5.1		not-accessible	An entry in the Sdsl Pm Current Day table.
G32 umSdslPmCurrentDayES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.5.1.1	Gauge32	read-only	The number of Errored Seconds encountered by an Sdsl during the Current Day.
G32 umSdslPmCurrentDaySES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.5.1.2	Gauge32	read-only	The number of Severely Errored Seconds encountered by an Sdsl during the Current Day.
G32 umSdslPmCurrentDayUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.5.1.3	Gauge32	read-only	The number of Unavailable Seconds encountered by an Sdsl during the Current Day.
umSdslPmDayTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.6		not-accessible	The SDSL Pm Day table.
umSdslPmDayEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.6.1		not-accessible	An entry in the Sdsl Pm Day table.
INT umSdslPmDayIndex	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.6.1.1	INTEGER	not-accessible	A number between 1 and 7, where 1 is the most recently completed day and 7 is the least recently completed day.
G32 umSdslPmDayES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.6.1.2	Gauge32	read-only	The number of Errored Seconds encountered by an Sdsl in one day.
G32 umSdslPmDaySES	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.6.1.3	Gauge32	read-only	The number of Severely Errored Seconds encountered by an Sdsl in one day.
G32 umSdslPmDayUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.6.1.4	Gauge32	read-only	The number of Unavailable Seconds encountered by an Sdsl in one day.
umSdslTestTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.7		not-accessible	A table containing SHDSL testing function.
umSdslTestEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.7.1		not-accessible	An entry in umSdslTestTable.
INT umSdslTestLoopback	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.7.1.1	INTEGER	read-write	This value is to set loopback. 0: Release 2: Loopback toward Network
INT umSdslTestPattern	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.7.1.2	INTEGER	read-write	This variable is used to set test pattern. 1: 511 2: 2047 3: PRBS Support Eoc Version 1.02 (23/04/2002)
INT umSdslTestPeriod	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.7.1.3	INTEGER	read-write	This variable is used to get/set test period in second. A value of 0 means non-stop testing.
T/F umSdslTestStart	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.7.1.4	TruthValue	read-write	This value is to start or stop testing(only local). TRUE (1): Start FALSE (2): Stop
T/F umSdslTestInsertOneBitError	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.7.1.5	TruthValue	read-write	This variable is used to initiate pause test pattern. This is used in error insertion application. (1) Insert error rate(rate= 10E-1)
INT umSdslTestElapsedTime	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.7.1.6	INTEGER	read-only	This variable is to indicate elapsed time of testing in second.
STR umSdslTestErrCount	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.7.1.7	DisplayString	read-only	This variable is to indicate error count of testing.
STR umSdslTestErrRate	1.3.6.1.4.1.2011.2.6.7.4.4.2.2.7.1.8	DisplayString	read-only	This variable is to indicate error rate of testing, which is 'a.bcx10E(-d)', a, b, c: 0..9, d: 1..9.
hwShdslCPEV35	1.3.6.1.4.1.2011.2.6.7.4.4.2.3
umSdslV35ConfigTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.1		not-accessible	The config table contains Ne config items.
umSdslV35ConfigEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.1.1		not-accessible	An entry in the config table
INT umSdslV35ConfigCurrentDataRate	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.1.1.1	INTEGER	read-only	This variable is to get current data rate (N*64k) of Sdsl V35.
INT umSdslV35ConfigCurrentTimingSrc	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.1.1.2	INTEGER	read-only	This variable is to get the current timing source of the system. 0: internal 1: from loop (SDSL) 2: from DTE (V.35)
INT umSdslV35ConfigTimingSrc	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.1.1.3	INTEGER	read-write	This variable is to get/set the setted timing source of the system. 0: internal 1: from loop (SDSL) 2: from DTE (V.35)
umSdslV35DTETable	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.2		not-accessible	The alarm table contains DTE.
umSdslV35DTEEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.2.1		not-accessible	An entry in the alarm table
INT umSdslV35DTEStatus	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.2.1.1	INTEGER	read-only	The variable represents which port reports the DTE Status. (bit) 0 : RTS 1 : CTS 2 : DCD 3 : DSR
INT umSdslV35DTERTS	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.2.1.2	INTEGER	read-write	The variable represents which port reports the RTS Config Status. 0 : RTS from DTE 1 : RTS Permanent On
INT umSdslV35TailFunc	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.2.1.3	INTEGER	read-write	The variable represents tail function switch. 0 : Tail off 1 : Tail on
umSdslV35LoopbackTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.3		not-accessible	The V35 Loopback Table.
umSdslV35LoopbackEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.3.1		not-accessible	An entry in the Sdsl Testing table.
INT umSdslV35Loopback	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.3.1.1	INTEGER	read-write	This value is to set loopback. 0: Release 1: Toward DTE Loop 2: Toward Network Loop 3: Initial in-band Loop (V.54)
umSdslV35AlarmTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.4		not-accessible	The alarm table contains alarm event history.
umSdslV35AlarmEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.4.1		not-accessible	An entry in the alarm table
T/F umSdslV35ClearAlarmHistory	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.4.1.1	TruthValue	read-write	The variable initiate the clear alarm history action(Set 1).
INT umSdslV35AlarmStatus	1.3.6.1.4.1.2011.2.6.7.4.4.2.3.4.1.2	INTEGER	read-only	The variable initiate the current alarm status. (bit) bit0: Loss of SDSL synchronization word (LOSW) bit1: (SDSL) ES exceed day threshold bit2: (SDSL) ES exceed quarter threshold bit3: (SDSL) SES exceed day threshold bit4: (SDSL) SES exceed quarter threshold bit5: (SDSL) UAS exceed day threshold bit6: (SDSL) UAS exceed quarter threshold bit7: (SDSL) SNR exceed threshold bit8: (SDSL) Loop Attuattion exceed threshold bit9~31: Reserved DataType = 72
hwCPET1E1	1.3.6.1.4.1.2011.2.6.7.4.4.2.4
umLiuTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.1		not-accessible	The LIU table. The LIU attributes regarding configuration and performance are defined in RFC1406.
umLiuEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.1.1		not-accessible	An entry in the LIU table.
INT umLiuE1Transparent	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.1.1.1	INTEGER	read-write	This value gets/sets the E1 Transparency. Disable(0), Enable (1)
INT umLiuLineDrive	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.1.1.2	INTEGER	read-write	This variable is to define the value of line drive. 75_Ohm(0), 120_Ohm(1)
INT umLiuIdleCodeword	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.1.1.3	INTEGER	read-write	This variable represents the value of idle code word. But the write-operation is preserved for future use. If you take write-operation, will be returned.
INT umLiuE1SlotMap	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.1.1.4	INTEGER	read-write	This table defines the corresponding customer equipment interface for each time slot of network interface. Each bit represents one time slot. '1' stands for occupied. The leftmost bit represents time slot 31, and rightmost bit represents time slot 0.
INT umLiuResetPerformance	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.1.1.5	INTEGER	read-write	This value is to reset performance register for this port. 1: reset all current performance data 2: reset current LCV 3: reset current PCV 4: reset current ES 5: reset current SES 6: reset current SEFS 7: reset current UAS 8: reset current CSS 9: reset current DM 10: reset current CS 11: reset current FBE 51: reset all history performance data 52: reset history LCV 53: reset history PCV 54: reset history ES 55: reset history SES 56: reset history SEFS 57: reset history UAS 58: reset history CSS 59: reset history DM 60: reset history CS 61: reset history FBE
umLiuTestTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2		not-accessible	The LIU table. The LIU attributes regarding configuration and performance are defined in RFC1406.
umLiuTestEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2.1		not-accessible	An entry in the LIU Test table.
INT umLiuLoopbackConfig	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2.1.1	INTEGER	read-write	This value is to set LIU loopback. 0: release 1: payload loopback 2: line loopback 3: local loopback
INT umLiuLoopbackStatus	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2.1.2	INTEGER	read-only	This value is to indicate the LIU loopback status. 0: released 1: payload loopback 2: line loopback 3: local loopback
INT umLiuTestPattern	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2.1.3	INTEGER	read-write	This variable is used to set test pattern. 1: 2E15-1_PRBS 3: 2047
INT umLiuTestPeriod	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2.1.4	INTEGER	read-write	This variable is used to set test period in second. A value of 0 means non-stop testing.
T/F umLiuTestStart	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2.1.5	TruthValue	read-write	This value is to start or stop testing. 1: Start 2: Stop
INT umLiuInsertedErrorRate	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2.1.6	INTEGER	read-write	This value is used to set inserted error rate. Inserted error rate = 1*10E(-n), where n is the set value. Set 0 to stop insertting errors.
INT umLiuElapsedTime	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2.1.7	INTEGER	read-only	This variable is to indicate elapsed time of testing.
STR umLiuTestErrCount	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2.1.8	DisplayString	read-only	This variable is to indicate error count of testing.
STR umLiuTestErrRate	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.2.1.9	DisplayString	read-only	This variable is to indicate error rate of testing, which is 'a.bcx10E(-d)', a, b, c: 0..9, d: 1..9.
umLiuThresholdTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3		not-accessible	The Performance threshold table.
umLiuThresholdEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1		not-accessible	An entry in Performance threshold table.
G32 umLiuThreshold15mLCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.1	Gauge32	read-write	This variable defines the threshold of LCV. This variable is valid for near end UM.
G32 umLiuThreshold15mPCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.2	Gauge32	read-write	This variable defines the threshold of PCV.
G32 umLiuThreshold15mES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.3	Gauge32	read-write	This variable defines the threshold of ES.
G32 umLiuThreshold15mSES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.4	Gauge32	read-write	This variable defines the threshold of SES.
G32 umLiuThreshold15mSEFS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.5	Gauge32	read-write	This variable defines the threshold of SEFS.
G32 umLiuThreshold15mUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.6	Gauge32	read-write	This variable defines the threshold of UAS.
G32 umLiuThreshold15mCSS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.7	Gauge32	read-write	This variable defines the threshold of CSS.
G32 umLiuThreshold15mDM	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.8	Gauge32	read-write	This variable defines the threshold of DM.
G32 umLiuThreshold24hLCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.9	Gauge32	read-write	This variable defines the threshold of LCV. This variable is valid for near end UM.
G32 umLiuThreshold24hPCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.10	Gauge32	read-write	This variable defines the threshold of PCV.
G32 umLiuThreshold24hES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.11	Gauge32	read-write	This variable defines the threshold of ES.
G32 umLiuThreshold24hSES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.12	Gauge32	read-write	This variable defines the threshold of SES.
G32 umLiuThreshold24hSEFS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.13	Gauge32	read-write	This variable defines the threshold of SEFS.
G32 umLiuThreshold24hUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.14	Gauge32	read-write	This variable defines the threshold of UAS.
G32 umLiuThreshold24hCSS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.15	Gauge32	read-write	This variable defines the threshold of CSS.
G32 umLiuThreshold24hDM	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.3.1.16	Gauge32	read-write	This variable defines the threshold of DM.
umLiuPmData	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4
umLiuPmCurrent15mTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1		not-accessible	The Liu PM Current table.
umLiuPmCurrent15mEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1		not-accessible	An entry in the Liu Pm Current 15 minutes table.
G32 umLiuPmCurrent15mLCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1.1	Gauge32	read-only	The number of Line Code Violations encountered by an LIU interface in the current quarter.
G32 umLiuPmCurrent15mPCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1.2	Gauge32	read-only	The number of Path Coding Violations encountered by an LIU interface in the current quarter.
G32 umLiuPmCurrent15mES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1.3	Gauge32	read-only	The number of Errored Seconds encountered by an LIU interface in the current quarter.
G32 umLiuPmCurrent15mSES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1.4	Gauge32	read-only	The number of Severely Errored Seconds encountered by an LIU interface in the current quarter.
G32 umLiuPmCurrent15mSEFS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1.5	Gauge32	read-only	The number of Severely Errored Framing Seconds encountered by an LIU interface in the current quarter.
G32 umLiuPmCurrent15mUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1.6	Gauge32	read-only	The number of Unavailable Seconds encountered by an LIU interface in the current quarter.
G32 umLiuPmCurrent15mCSS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1.7	Gauge32	read-only	The number of Controlled Slip Seconds encountered by an LIU interface in the current quarter.
G32 umLiuPmCurrent15mDM	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1.8	Gauge32	read-only	The number of Degraded Minutes encountered by an LIU interface in the current quarter.
G32 umLiuPmCurrent15mCS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1.9	Gauge32	read-only	The number of Controlled Slip encountered by an LIU interface in the current quarter.
G32 umLiuPmCurrent15mFBE	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.1.1.10	Gauge32	read-only	The number of Loss Of Frame encountered by an LIU interface in current quarter.
umLiuPm15mTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2		not-accessible	The Liu PM 15 minutes Interval table.
umLiuPm15mEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1		not-accessible	An entry in the Liu Pm Interval table.
INT umLiuPm15mIndex	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.1	INTEGER	not-accessible	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 umLiuPm15mLCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.2	Gauge32	read-only	The number of Line Code Violations encountered by a LIU interface in one of the previous 96, individual 15 minute, intervals.
G32 umLiuPm15mPCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.3	Gauge32	read-only	The number of Path Coding Violations encountered by a LIU interface in one of the previous 96, individual 15 minute, intervals.
G32 umLiuPm15mES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.4	Gauge32	read-only	The number of Errored Seconds encountered by a LIU interface in one of the previous 96, individual 15 minute, intervals.
G32 umLiuPm15mSES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.5	Gauge32	read-only	The number of Severely Errored Seconds encountered by a LIU interface in one of the previous 96, individual 15 minute, intervals.
G32 umLiuPm15mSEFS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.6	Gauge32	read-only	The number of Severely Errored Framing Seconds encountered by a LIU interface in one of the previous 96, individual 15 minute, intervals.
G32 umLiuPm15mUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.7	Gauge32	read-only	The number of Unavailable Seconds encountered by a LIU interface in one of the previous 96, individual 15 minute, intervals.
G32 umLiuPm15mCSS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.8	Gauge32	read-only	The number of Controlled Slip Seconds encountered by a LIU interface in one of the previous 96, individual 15 minute, intervals.
G32 umLiuPm15mDM	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.9	Gauge32	read-only	The number of Degraded Minutes encountered by a LIU interface in one of the previous 96, individual 15 minute, intervals.
G32 umLiuPm15mCS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.10	Gauge32	read-only	The number of Controlled Slip encountered by a LIU interface in one of the previous 96, individual 15 minute, intervals.
G32 umLiuPm15mFBE	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.2.1.11	Gauge32	read-only	The number of Loss Of Frame encountered by a LIU interface in one of the previous 96, individual 15 minute, intervals.
umLiuPmCurrentDayTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3		not-accessible	The Liu PM Current Day table.
umLiuPmCurrentDayEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1		not-accessible	An entry in the Liu Pm Current Day table.
G32 umLiuPmCurrentDayLCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1.1	Gauge32	read-only	The number of Line Code Violations encountered by an LIU interface in current day.
G32 umLiuPmCurrentDayPCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1.2	Gauge32	read-only	The number of Path Coding Violations encountered by an LIU interface in current day.
G32 umLiuPmCurrentDayES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1.3	Gauge32	read-only	The number of Errored Seconds encountered by an LIU interface in current day.
G32 umLiuPmCurrentDaySES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1.4	Gauge32	read-only	The number of Severely Errored Seconds encountered by an LIU interface in current day.
G32 umLiuPmCurrentDaySEFS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1.5	Gauge32	read-only	The number of Severely Errored Framing Seconds encountered by an LIU interface in current day.
G32 umLiuPmCurrentDayUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1.6	Gauge32	read-only	The number of Unavailable Seconds encountered by an LIU interface in current day.
G32 umLiuPmCurrentDayCSS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1.7	Gauge32	read-only	The number of Controlled Slip Seconds encountered by an LIU interface in current day.
G32 umLiuPmCurrentDayDM	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1.8	Gauge32	read-only	The number of Degraded Minutes encountered by an LIU interface in current day.
G32 umLiuPmCurrentDayCS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1.9	Gauge32	read-only	The number of Controlled Slip encountered by an LIU interface in current day.
G32 umLiuPmCurrentDayFBE	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.3.1.10	Gauge32	read-only	The number of Loss Of Frame encountered by an LIU interface in current day.
umLiuPmDayTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4		not-accessible	The Liu PM Day table.
umLiuPmDayEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1		not-accessible	An entry in the Liu Pm Day table.
INT umLiuPmDayIndex	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.1	INTEGER	not-accessible	A number between 1 and 7, where 1 is PM data of the most recently completed day and 7 is PM data of the least completed recently day.
G32 umLiuPmDayLCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.2	Gauge32	read-only	The number of Line Code Violations encountered by an LIU interface in one day.
G32 umLiuPmDayPCV	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.3	Gauge32	read-only	The number of Path Coding Violations encountered by an LIU interface in one day.
G32 umLiuPmDayES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.4	Gauge32	read-only	The number of Errored Seconds encountered by an LIU interface in one day.
G32 umLiuPmDaySES	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.5	Gauge32	read-only	The number of Severely Errored Seconds encountered by an LIU interface in one day.
G32 umLiuPmDaySEFS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.6	Gauge32	read-only	The number of Severely Errored Framing Seconds encountered by an LIU interface in one day.
G32 umLiuPmDayUAS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.7	Gauge32	read-only	The number of Unavailable Seconds encountered by an LIU interface in one day.
G32 umLiuPmDayCSS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.8	Gauge32	read-only	The number of Controlled Slip Seconds encountered by an LIU interface in one day.
G32 umLiuPmDayDM	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.9	Gauge32	read-only	The number of Degraded Minutes encountered by an LIU interface in one day.
G32 umLiuPmDayCS	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.10	Gauge32	read-only	The number of Controlled Slip encountered by an LIU interface in one day.
G32 umLiuPmDayFBE	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.4.4.1.11	Gauge32	read-only	The number of Loss Of Frame by an LIU interface in one day.
umSdslE1T1AlarmTable	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.5		not-accessible	The SDSL E1T1 alarm table.
umSdslE1T1AlarmEntry	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.5.1		not-accessible	An entry in the SDSL alarm table.
T/F umSdslE1T1ClearAlarmHistory	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.5.1.1	TruthValue	read-write	The variable initiate the clear alarm history action(Set 1).
U32 umSdslE1T1LocalAlarmStatus	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.5.1.2	Unsigned32	read-only	The variable initiate the local current alarm status. (bit) 0: (E1T1) E1 LOS Failure (Loss of signal) 1: (E1T1) Loss of Frame Alignment 2: (E1T1) Loss of E1T1 Multiframe Alignment 3: (E1T1) AIS received 4: (E1T1) AIS received in TS16 5: (E1T1) RAI received 6: (E1T1) RAI received in TS16 7: (E1T1) Bit errors exceed error ratio 8: (E1T1) LCV exceed day threshold 9: (E1T1) LCV exceed quarter threshold 10: (E1T1) PCV exceed day threshold 11: (E1T1) PCV exceed quarter threshold 12: (E1T1) ES exceed day threshold 13: (E1T1) ES exceed quarter threshold 14: (E1T1) SES exceed day threshold 15: (E1T1) SES exceed quarter threshold 16: (E1T1) SEFS exceed day threshold 17: (E1T1) SEFS exceed quarter threshold 18: (E1T1) UAS exceed day threshold 19: (E1T1) UAS exceed quarter threshold 20: (E1T1) CSS exceed day threshold 21: (E1T1) CSS exceed quarter threshold 22: (E1T1) DM exceed day threshold 23: (E1T1) DM exceed quarter threshold 24~31 Reserved DataType 103
U32 umSdslE1T1SdslAlarmStatus	1.3.6.1.4.1.2011.2.6.7.4.4.2.4.5.1.3	Unsigned32	read-only	The variable initiate the E1T1 SHDSL current alarm status. (bit) 0: (SDSL) LOSW Failure (Loss of SDSL synchronization word) 1: (SDSL) ES exceed day threshold 2: (SDSL) ES exceed quarter threshold 3: (SDSL) SES exceed day threshold 4: (SDSL) SES exceed quarter threshold 5: (SDSL) UAS exceed day threshold 6: (SDSL) UAS exceed quarter threshold 7: (SDSL) SNR exceed threshold 8: (SDSL) Loop Attuattion exceed threshold 9~31 Reserved DataType 103

RFC description

Manages SHDSL customer premises equipment including inventory, firmware versions, and line status.

Start monitoring Huawei Technologies SHDSL CPE device with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HWMUSA-SHDSL-CPE-MIB

What Is HWMUSA-SHDSL-CPE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description