All MIBs › HWMUSA-SIGTRAN-MIB
Organization: Huawei Technologies Co.,Ltd.
Last Updated: 2012-02-29
Category: Domain: Telco/Transport, Vendor: Huawei
Description: Huawei MUSA MIB for SIGTRAN protocol management providing configuration and status objects for SS7 over IP transport.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HWMUSA-SIGTRAN-MIB?
HWMUSA-SIGTRAN-MIB is a Huawei MUSA-platform MIB for managing SIGTRAN, the protocol suite that carries SS7 telephony signaling over IP transport. Its content is dominated by trap/notification definitions covering SIGTRAN's sub-layers, including common alarms and the L2UA (Layer 2 User Adaptation) sub-protocol used to backhaul signaling links over IP. This makes it primarily a fault-monitoring MIB, used to detect and alert on protocol-stack faults such as signaling link failures and adaptation-layer errors rather than hardware sensors like temperature or fans. It builds on the SIGTRAN protocol family (an IETF-defined signaling transport standard) and Huawei's broader IAS alarm framework. It is deployed in telecom carrier networks where Huawei signaling gateways backhaul SS7 traffic over IP and need centralized alarm monitoring, making the HWMUSA-SIGTRAN-MIB MIB an essential reference for engineers configuring SIGTRAN fault alerts.
IPNetwork Monitor allows you to monitor SNMP objects defined in HWMUSA-SIGTRAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei SIGTRAN signaling gateway / media gateway controller
Monitoring Examples
The hwIASSigtranL2uaAlarmTraps and hwIASSigtranCommonTraps notification groups would be received by an NMS trap collector to flag SIGTRAN Layer 2 User Adaptation link failures or other common signaling faults; a burst of hwIASSigtranAlarmTraps typically indicates a degraded SS7-over-IP signaling path.
What Can Be Monitored
- SIGTRAN alarm notifications
- L2UA link alarm state
- common SIGTRAN fault traps
- signaling transport fault events
This MIB depends on
Related MIBs
Imported Objects
From HUAWEI-MIB
| ias | OBJECT-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 | |
| private |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION |
How to Use in IPNetwork Monitor
Example using hwSctpGlobalStatAssocCurEstab OID:
Select a Huawei SIGTRAN signaling gateway / media gateway controller as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hwSctpGlobalStatAssocCurEstab into the Find box to locate it in the OID tree, then select it and click OK. The number of current associations. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the count changes from its expected baseline, since that would indicate the underlying set of items changed unexpectedly. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hwIASSigtran | 1.3.6.1.4.1.2011.2.6.7.6 | |||
| hwIASSigtranObjects | 1.3.6.1.4.1.2011.2.6.7.6.1 | This MIB module defines MIB objects which provides SIGTRAN management. | ||
| hwL2uaLinkSetMngtTable | 1.3.6.1.4.1.2011.2.6.7.6.1.1 | not-accessible | This table is used to config L2UA linkset. The index of this table is hwL2uaLinkSetNo. | |
| hwL2uaLinkSetMngtEntry | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1 | not-accessible | This table is used to config L2UA linkset. The index of this entry is hwL2uaLinkSetNo. | |
| I32 hwL2uaLinkSetNo | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.1 | Integer32 | not-accessible | The link set number |
| INT hwL2uaLinkSetProtocolType | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.2 | INTEGER | read-write | Protocol type. Options: 1. iua(1) -indicates that the Protocol type is IUA 2. m2ua(2) -indicates that that the Protocol type is M2UA 3. v5ua(5) -indicates that that the Protocol type is V5UA(currently, only IUA is supported.) |
| I32 hwL2uaLinkSetPendingTime | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.3 | Integer32 | read-write | The pending time of the link set (the last active link in the link set switches to another state. During the pending time length, if no link in the link set switches to the active state, the link set enters the inactive or down state.). Default: 4 Unit: second |
| INT hwL2uaLinkSetTrafficMode | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.4 | INTEGER | read-write | The working mode of the link set. Options: 1. override(1) -indicates that the working mode of the link set is override 2. loadshare(2) -indicates that the working mode of the link set is loadshare |
| INT hwL2uaLinkSetCSMode | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.5 | INTEGER | read-write | C/S mode of the link set. Options: 1. client(1) -indicates that the C/S mode of the link set is Client 2. server(2) -indicates that the C/S mode of the link set is Server Default: 2 |
| INT hwL2uaLinkSetIIDType | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.6 | INTEGER | read-only | Type of the interface ID. Options: 1. integer(1) -integer 2. text(2) -text |
| I32 hwL2uaLinkSetLinkNum | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.7 | Integer32 | read-only | The number of links in the link set |
| INT hwL2uaLinkSetOperState | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.8 | INTEGER | read-only | Status of the link set. Options: 1. down(1) -indicates that the Status of the link set is down 2. inactive(2) -indicates that the Status of the link set is inactive 3. active(3) -indicates that the Status of the link set is active 4. pending(4) -indicates that the Status of the link set is pending |
| ROW hwL2uaLinkSetRowStatus | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.9 | RowStatus | read-write | Row status |
| I32 hwL2uaLinkSetMgId | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.10 | Integer32 | read-write | MG interface ID. -1 means this parameter is not configured. |
| I32 hwL2uaLinkSetIidMap | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.11 | Integer32 | read-write | InterfaceID generation mode. 1:generated by user input,use format:interfaceID 2:generated automatically,use format:ffsspp, ff-shelf number,ss-slot number, pp-port number, decimal number 3:generated automatically,use format:rrrrfffffssssspppppppxxxxxxxxxxx ,rrrr-rack, fffff-shelf number,sssss-slot number, ppppppp-port number,xxxxxxxxxxx-reserved,binary number 4:generated automatically,FT text format:prefix+ff/ss/pp, ff-shelf number,ss-slot number, pp-port number, text 5:generated by user input,use format:braprefix+interfaceID+brasuffix or praprefix+interfaceID+prasuffix, the length of praprefix+interfaceID+prasuffix must be shorter than 31 Default:1 |
| INT hwL2uaLinkSetJointlyWork | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.12 | INTEGER | read-write | IUA link joint work with MGC. Options: 1.enable(1) -support IUA Link joint work with MGC 2.disable(2) -not support IUA Link joint work with MGC It must config together with hwL2uaLinkSetMgId. |
| OCT hwL2uaLinkSetIidPrefix | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.13 | OCTET STRING | read-write | Indicates the prefix of IID.The prefix is not allowed to contain the character:';'':'',' |
| OCT hwL2uaLinkSetIidBraPrefix | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.14 | OCTET STRING | read-write | Indicates the bra prefix of IID.The prefix is not allowed to contain the character:';'':'',' |
| OCT hwL2uaLinkSetIidBraSuffix | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.15 | OCTET STRING | read-write | Indicates the bra suffix of IID.The suffix is not allowed to contain the character:';'':'',' |
| OCT hwL2uaLinkSetIidPraPrefix | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.16 | OCTET STRING | read-write | Indicates the pra prefix of IID.The prefix is not allowed to contain the character:';'':'',' |
| OCT hwL2uaLinkSetIidPrasuffix | 1.3.6.1.4.1.2011.2.6.7.6.1.1.1.17 | OCTET STRING | read-write | Indicates the pra suffix of IID.The suffix is not allowed to contain the character:';'':'',' |
| hwL2uaLinkMngtTable | 1.3.6.1.4.1.2011.2.6.7.6.1.2 | not-accessible | This table is used to config L2UA link. The index of this table is hwL2uaLinkNo. | |
| hwL2uaLinkMngtEntry | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1 | not-accessible | This table is used to config L2UA link. The index of this entry is hwL2uaLinkNo. | |
| I32 hwL2uaLinkNo | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.1 | Integer32 | not-accessible | Link No. |
| I32 hwL2uaLinkLinkSetNo | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.2 | Integer32 | read-write | Link set No. |
| I32 hwL2uaLinkLocalPort | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.3 | Integer32 | read-write | Local port number |
| IP hwL2uaLinkLocalIpaddr | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.4 | IpAddress | read-write | Local IP address |
| I32 hwL2uaLinkRemotePort | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.5 | Integer32 | read-write | Remote port number |
| IP hwL2uaLinkRemoteIpaddr1 | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.6 | IpAddress | read-write | Remote IP address 1 |
| IP hwL2uaLinkRemoteIpaddr2 | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.7 | IpAddress | read-write | Remote IP address 2 |
| I32 hwL2uaLinkMaxInStreamNum | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.8 | Integer32 | read-write | Maximum number of inbound streams. -1 means the IUA link is configurated with DHCP but the vlan IP isn't gained by DHCP. |
| I32 hwL2uaLinkMaxOutStreamNum | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.9 | Integer32 | read-write | Maximum number of outbound streams. -1 means the IUA link is configurated with DHCP but the vlan IP isn't gained by DHCP. |
| INT hwL2uaLinkActiveStandbyFlag | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.10 | INTEGER | read-only | Active and standby flag. Options: 1. active(1)-indicates that the Active and standby flag is active 2. standby(2)-indicates that the Active and standby flag is standby 3. null(-1)-indicates that the Active and standby flag is invalid Display -1 when the vlanid can't get Local IP in dhcp mode. |
| INT hwL2uaLinkLockFlag | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.11 | INTEGER | read-write | IUA Link maintenance lock flag. Options: 1. lock(1)-indicates that the IUA Link maintenance lock flag is active 2. unlock(2)-indicates that the IUA Link maintenance lock flag is standby |
| I32 hwL2uaLinkUsedInStreamNum | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.12 | Integer32 | read-only | Number of inbound streams used currently -1 indicates that the number is invalid |
| I32 hwL2uaLinkUsedOutStreamNum | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.13 | Integer32 | read-only | Number of outbound streams used currently -1 indicates that the number is invalid |
| I32 hwL2uaLinkSctpAssocId | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.14 | Integer32 | read-only | SCTP association ID that the L2UA link corresponds to -1 means there is no SCTP association. |
| INT hwL2uaLinkOperState | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.15 | INTEGER | read-only | Link status. Options: 1. unestablish(1)-indicates that the Link status is active 2. establish(2)-indicates that the Link status is standby 3. inactive(3)-indicates that the Link status is inactive 4. active(4)-indicates that the Link status is active |
| INT hwL2uaLinkCongestState | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.16 | INTEGER | read-only | Congestion state. Options: 1. uncongest(1) -not congested 2. congest(2) -congested 3. null(-1) -null Display -1 when the vlanid can't get Local IP in dhcp mode. |
| INT hwL2uaLinkMaintainOper | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.17 | INTEGER | read-write | Link maintenance operation. Options: 1. lock(1) -indicates that the link maintenance operation is Lock 2. unlock(2) -indicates that the link maintenance operation is Unlock 3. reset(3) -indicates that the link status is Reset 4. null(-1) -indicates that the link maintenance operation is invalid |
| ROW hwL2uaLinkRowStatus | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.18 | RowStatus | read-write | Row status |
| I32 hwL2uaLinkWithMedGwyCtrlIdx | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.19 | Integer32 | read-write | Config IUA Link jiont work with witch MGC. 0: Primary MGC. 1: Secondary MGC. -1 means this parameter is not configed. |
| I32 hwL2uaLinkPriority | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.20 | Integer32 | read-write | Is available when the working mode of the link set is Load-share. In Over ride mode, this parameter can be read, but no use. Default:0 |
| INT hwL2uaLinkLockStatus | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.21 | INTEGER | read-only | IUA Link current Lock State: Options: 1. unlock(1)-indicates that the Current IUA Link not locked 2. servicelock(2)-indicates that the Current IUA Link was locked for joint work with MGC 3. maintenancelock(3)-indicates that the Current IUA Link was locked by maintenance operation Adminlock have pripority over autolock. 4. display -1 when the vlanid can't get Local IP in dhcp mode. |
| I32 hwL2uaLinkLocalIpaddrDhcpClientIndex | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.22 | Integer32 | read-write | Dhcp L2ua vlan id. The valid value is 1..4093,if the value is -1, the static signal ip will be used. |
| OCT hwL2uaLinkLocalIpDnyAddrName | 1.3.6.1.4.1.2011.2.6.7.6.1.2.1.23 | OCTET STRING | read-write | Dynamic local IP name. |
| hwSctpAssocStatTable | 1.3.6.1.4.1.2011.2.6.7.6.1.7 | not-accessible | This table is used to query statistic of a SCTP association. The index of this table is hwSctpAssocStatAssocId. | |
| hwSctpAssocStatEntry | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1 | not-accessible | This table is used to query statistic of a SCTP association. The index of this entry is hwSctpAssocStatAssocId. | |
| I32 hwSctpAssocStatAssocId | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1.1 | Integer32 | not-accessible | SCTP association ID Constructed by Protocol-Type, MGC-index/Proxy-index, IUA-Link-ID/H248-Interface-ID/SIP-Interface-ID; Format:xyzzzzzz(Hex) a) x for Protocol-Type: IUA(0),H.248(1),SIP(2); b) y for MGC-index/Proxy-index: if x is IUA(0), y fixed to 0; if x is H.248(1), y for MGC index; if x is SIP(2), y for Proxy index; c) z for IUA-Link-ID/H248-Interface-ID/SIP-Interface-ID: if x is IUA(0), zzzzzz for IUA LinkNo; if x is H.248(1), zzzzzz for H248 interface ID; if x is SIP(2), zzzzzz for SIP interface ID; |
| I32 hwSctpAssocStatT1Expired | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1.2 | Integer32 | read-only | The expired times of the T1 timer |
| I32 hwSctpAssocStatT2Expired | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1.3 | Integer32 | read-only | The expired times of the T2 timer |
| I32 hwSctpAssocStatRetransChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1.4 | Integer32 | read-only | The number of retransmitted data chunks |
| I32 hwSctpAssocStatSendDataChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1.5 | Integer32 | read-only | The number of transmitted data chunks. |
| I32 hwSctpAssocStatRevDataChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1.6 | Integer32 | read-only | The number of received data chunks |
| I32 hwSctpAssocStatRecPackets | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1.7 | Integer32 | read-only | The number of received SCTP packets |
| I32 hwSctpAssocStatRecErrPackets | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1.8 | Integer32 | read-only | The number of received error SCTP packets |
| INT hwSctpAssocStatOperStatus | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1.9 | INTEGER | read-write | Clearing the statistics of the associations. Options: 1. clear(1) -clear |
| I32 hwSctpAssocStatSentSctpPackets | 1.3.6.1.4.1.2011.2.6.7.6.1.7.1.10 | Integer32 | read-only | The number of the transmitted SCTP packets |
| hwSctpGlobalStatTable | 1.3.6.1.4.1.2011.2.6.7.6.1.8 | |||
| I32 hwSctpGlobalStatAssocCurEstabEx | 1.3.6.1.4.1.2011.2.6.7.6.1.8.1 | Integer32 | read-only | The number of current associations |
| I32 hwSctpGlobalStatAssocActEstab | 1.3.6.1.4.1.2011.2.6.7.6.1.8.2 | Integer32 | read-only | The number of associations initiated by the local end |
| I32 hwSctpGlobalStatAssocPassiveEstab | 1.3.6.1.4.1.2011.2.6.7.6.1.8.3 | Integer32 | read-only | The number of associations initiated by the remote end |
| I32 hwSctpGlobalStatAssocActFail | 1.3.6.1.4.1.2011.2.6.7.6.1.8.4 | Integer32 | read-only | The number of failure associations initiated by the local end |
| I32 hwSctpGlobalStatAssocPassiveFail | 1.3.6.1.4.1.2011.2.6.7.6.1.8.5 | Integer32 | read-only | The number of failure associations initiated by the remote end |
| I32 hwSctpGlobalStatAssocAborted | 1.3.6.1.4.1.2011.2.6.7.6.1.8.6 | Integer32 | read-only | The number of abort associations |
| I32 hwSctpGlobalStatAssocShutdown | 1.3.6.1.4.1.2011.2.6.7.6.1.8.7 | Integer32 | read-only | The number of shutdown associations |
| I32 hwSctpGlobalStatRecOotb | 1.3.6.1.4.1.2011.2.6.7.6.1.8.8 | Integer32 | read-only | The number of received abnormal data chunks at the local end |
| I32 hwSctpGlobalStatSendCtrlChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.8.9 | Integer32 | read-only | The number of transmitted control data chunks |
| I32 hwSctpGlobalStatSendOrderChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.8.10 | Integer32 | read-only | The number of transmitted ordered data chunks |
| I32 hwSctpGlobalStatSendUnorderChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.8.11 | Integer32 | read-only | The number of transmitted unordered data chunks |
| I32 hwSctpGlobalStatRecCtrlChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.8.12 | Integer32 | read-only | The number of received control data chunks |
| I32 hwSctpGlobalStatRecOrderChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.8.13 | Integer32 | read-only | The number of received ordered data chunks |
| I32 hwSctpGlobalStatRecUnorderChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.8.14 | Integer32 | read-only | The number of received unordered data chunks |
| I32 hwSctpGlobalStatRetransDataChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.8.15 | Integer32 | read-only | The number of retransmitted data chunks |
| I32 hwSctpGlobalStatFragmentedUsrMsgs | 1.3.6.1.4.1.2011.2.6.7.6.1.8.16 | Integer32 | read-only | The number of fragmented user messages |
| I32 hwSctpGlobalStatReassembledUsrMsgs | 1.3.6.1.4.1.2011.2.6.7.6.1.8.17 | Integer32 | read-only | The number of reassembled user messages |
| I32 hwSctpGlobalStatChecksumErrors | 1.3.6.1.4.1.2011.2.6.7.6.1.8.18 | Integer32 | read-only | The number of received checksum error packets |
| I32 hwSctpGlobalStatSentSctpPacks | 1.3.6.1.4.1.2011.2.6.7.6.1.8.19 | Integer32 | read-only | The number of the transmitted SCTP packets |
| I32 hwSctpGlobalStatRecvSctpPacks | 1.3.6.1.4.1.2011.2.6.7.6.1.8.20 | Integer32 | read-only | The number of the received SCTP packets |
| INT hwSctpGlobalStatAdminStatus | 1.3.6.1.4.1.2011.2.6.7.6.1.8.21 | INTEGER | read-write | Clearing the system statistics. Options: 1. clear(1) -clear |
| hwSctpParaTable | 1.3.6.1.4.1.2011.2.6.7.6.1.9 | |||
| I32 hwSctpParaRtoMin | 1.3.6.1.4.1.2011.2.6.7.6.1.9.1 | Integer32 | read-write | The minimum RTO. To the UA5000R15C05, this leaf can be read and written, the value range is (10..5000). To other products, this leaf just can be read, the default value is 1000. Unit: millisecond |
| I32 hwSctpParaRtoMax | 1.3.6.1.4.1.2011.2.6.7.6.1.9.2 | Integer32 | read-write | The maximum RTO. For Mg interface, default value 3000. For Iua-Link, default value 60000. To the UA5000R15C05, the value range is (200..120000). To other products, the value range is (3000..90000). Unit: millisecond |
| I32 hwSctpParaRtoInit | 1.3.6.1.4.1.2011.2.6.7.6.1.9.3 | Integer32 | read-write | The initial RTO. To the UA5000R15C05, the value range is (10..120000), the default value is 100. To other products, the value range is (1000..6000), the default value is 3000. Unit: millisecond |
| I32 hwSctpParaValidCookieLife | 1.3.6.1.4.1.2011.2.6.7.6.1.9.4 | Integer32 | read-write | Cookie lifecycle. To the UA5000R15C05, the value range is (5000..120000). To other products, the value range is (30000..120000). Default: 60000 Unit: millisecond |
| I32 hwSctpParaMaxInitRetrans | 1.3.6.1.4.1.2011.2.6.7.6.1.9.5 | Integer32 | read-write | The maximum retransmit attempts of INIT To the UA5000R15C05, the value range is (1..10). To other products, the value range is (3..10). Default: 6 |
| I32 hwSctpParaRtoAlpha | 1.3.6.1.4.1.2011.2.6.7.6.1.9.6 | Integer32 | read-write | Parameter of RTO Alpha To the UA5000R15C05, the default value is 13, the value range is (1..100). To other products, the default value is 12, the value range is (0..100). |
| I32 hwSctpParaRtoBeta | 1.3.6.1.4.1.2011.2.6.7.6.1.9.7 | Integer32 | read-write | Parameter of RTO Beta To the UA5000R15C05, the value range is (1..100). To other products, the value range is (0..100). Default: 25 |
| I32 hwSctpParaAssocMaxRetrans | 1.3.6.1.4.1.2011.2.6.7.6.1.9.8 | Integer32 | read-write | The maximum retransmit attempts in a association To the UA5000R15C05, the value range is (1..10), the default value is 8. To other products, the value range is (8..16), the default value is 10. |
| I32 hwSctpParaPathMaxRetrans | 1.3.6.1.4.1.2011.2.6.7.6.1.9.9 | Integer32 | read-write | The maximum Retransmit attempts in a path To the UA5000R15C05, the value range is (1..10), the default value is 8. To other products, the value range is (3..8), the default value is 5. |
| I32 hwSctpParaNoCongestionLevel | 1.3.6.1.4.1.2011.2.6.7.6.1.9.10 | Integer32 | read-write | Parameter of no-congestion level To the UA5000R15C05, the value range is (1..60). To other products, the value range is (0..60). Default: 40 |
| I32 hwSctpParaLowCongestionLevel | 1.3.6.1.4.1.2011.2.6.7.6.1.9.11 | Integer32 | read-write | Parameter of low-congestion level. Default: 60 |
| I32 hwSctpParaHighCongestionLevel | 1.3.6.1.4.1.2011.2.6.7.6.1.9.12 | Integer32 | read-write | Parameter of high-congestion level. Default: 80 |
| I32 hwSctpParaHbInterval | 1.3.6.1.4.1.2011.2.6.7.6.1.9.13 | Integer32 | read-write | Heartbeat interval. To the UA5000R15C05, the value range is (1000..300000), the default value is 3000. To other products, the value range is (2000..120000), the default value is 30000. Unit: millisecond |
| INT hwSctpParaSendChecksum | 1.3.6.1.4.1.2011.2.6.7.6.1.9.14 | INTEGER | read-write | Sending the checksum. Options: 1. no(1) -indicates that the checksum is not Sending 2. yes(2) -indicates that the checksum is Sending Default: 2 |
| INT hwSctpParaRecvChecksum | 1.3.6.1.4.1.2011.2.6.7.6.1.9.15 | INTEGER | read-write | Receiving the checksum. Options: 1. no(1) -indicates that the checksum is not Receiving 2. yes(2) -indicates that the checksum is Receiving Default: 2 |
| INT hwSctpParaChecksumArith | 1.3.6.1.4.1.2011.2.6.7.6.1.9.16 | INTEGER | read-write | Checksum algorithm. Options: 1. adler32(1) -indicates that Checksum algorithm is ADLER32 2. crc32(2) -indicates that Checksum algorithm is CRC32 Default: 2 |
| I32 hwSctpParaSACKPolicy | 1.3.6.1.4.1.2011.2.6.7.6.1.9.17 | Integer32 | read-write | SACK policy: 0-NoTimer; 1-Timer; 2-Commix. Default: 2 |
| I32 hwSctpParaSACKPeriod | 1.3.6.1.4.1.2011.2.6.7.6.1.9.18 | Integer32 | read-write | SACK period. Default: 20 Unit: millisecond |
| I32 hwSctpParaSACKFrquency | 1.3.6.1.4.1.2011.2.6.7.6.1.9.19 | Integer32 | read-write | Parameter of SACK frequency Default: 1 |
| I32 hwSctpParaMTU | 1.3.6.1.4.1.2011.2.6.7.6.1.9.20 | Integer32 | read-write | Parameter of MTU size. Default: 1500 |
| hwL2uaVersionTable | 1.3.6.1.4.1.2011.2.6.7.6.1.10 | |||
| OCT hwIuaVersionString | 1.3.6.1.4.1.2011.2.6.7.6.1.10.1 | OCTET STRING | read-only | The version of the L2UA protocol |
| hwSctpVersionTable | 1.3.6.1.4.1.2011.2.6.7.6.1.11 | |||
| OCT hwSctpVersionString | 1.3.6.1.4.1.2011.2.6.7.6.1.11.1 | OCTET STRING | read-only | SCTP version |
| hwSctpAssocInfoTable | 1.3.6.1.4.1.2011.2.6.7.6.1.12 | not-accessible | This table is used to query infomation of a SCTP association. The index of this table is hwSctpAssocId. | |
| hwSctpAssocInfoEntry | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1 | not-accessible | This table is used to query infomation of a SCTP association. The index of this entry is hwSctpAssocId. | |
| I32 hwSctpAssocId | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.1 | Integer32 | not-accessible | SCTP association ID Constructed by Protocol-Type, MGC-index/Proxy-index, IUA-Link-ID/H248-Interface-ID/SIP-Interface-ID; Format:xyzzzzzz(Hex) a) x for Protocol-Type: IUA(0),H.248(1),SIP(2); b) y for MGC-index/Proxy-index: if x is IUA(0), y fixed to 0; if x is H.248(1), y for MGC index; if x is SIP(2), y for Proxy index; c) z for IUA-Link-ID/H248-Interface-ID/SIP-Interface-ID: if x is IUA(0), zzzzzz for IUA LinkNo; if x is H.248(1), zzzzzz for H248 interface ID; if x is SIP(2), zzzzzz for SIP interface ID; |
| INT hwSctpAssocState | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.2 | INTEGER | read-only | Current status of the association Options: 1. closed(1) -indicates that the Current status of the association is closed 2. cookiewait(2) -indicates that the Current status of the association is down 3. cookieecho(3) -indicates that the Current status of the association is cookieecho 4. established(4) -indicates that the Current status of the association is established 5. shutdownpending(5) -indicates that the Current status of the association is shutdownpending 6. shutdownsent(6) -indicates that the Current status of the association is shutdownsent 7. shutdownreceived(7) -indicates that the Current status of the association is shutdownreceived 8. shutdownacksent(8) -indicates that the Current status of the association is shutdownacksent |
| INT hwSctpAssocType | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.3 | INTEGER | read-only | Association type. Options: 1. client(1) -indicates that the Association type is Client 2. server(2) -indicates that the Association type is Server |
| I32 hwSctpAssocApplId | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.4 | Integer32 | read-only | The upper-layer user ID |
| I32 hwSctpAssocLocalPort | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.5 | Integer32 | read-only | Local port number |
| I32 hwSctpAssocRemotePort | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.6 | Integer32 | read-only | Remote port number |
| IP hwSctpAssocLocalIPaddr | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.7 | IpAddress | read-only | The current local primary IP address |
| IP hwSctpAssocRemoteIPaddr | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.8 | IpAddress | read-only | The current remote primary IP address |
| INT hwSctpAssocAllowHB | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.9 | INTEGER | read-only | Whether transmitting HB message. Options: 1. no(1) -indicates not transmitting HB message 2. yes(2) -indicates transmitting HB message Default: 2 |
| U32 hwSctpAssocLocalRwnd | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.10 | Unsigned32 | read-only | The size of the local receiver window |
| U32 hwSctpAssocRemoteRwnd | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.11 | Unsigned32 | read-only | The size of the remote receiver window |
| I32 hwSctpAssocUnfirmDataChunks | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.12 | Integer32 | read-only | The size of the unacknowledged data that is transmitted |
| IP hwSctpAssocRemoteIP1addr | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.13 | IpAddress | read-only | Remote IP address 1. Default: 80 |
| INT hwSctpAssocRemoteIP1State | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.14 | INTEGER | read-only | The current status of remote IP address 1. Options: 1. active(1) -active 2. inactive(2) -inactive |
| I32 hwSctpAssocRemoteIP1WaitAck | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.15 | Integer32 | read-only | The number of the data blocks that is waiting for the acknowledgement by the remote SACK. Default: 2 |
| I32 hwSctpAssocRemoteIP1Cwnd | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.16 | Integer32 | read-only | The size of the congestion window. Default: 2 |
| I32 hwSctpAssocRemoteIP1Unfirm | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.17 | Integer32 | read-only | The size of the unacknowledged data that is transmitted on the path. Default: 2 |
| I32 hwSctpAssocRemoteIP1Rto | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.18 | Integer32 | read-only | Retransmission Time-out (ms) |
| I32 hwSctpAssocRemoteIP1Srtt | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.19 | Integer32 | read-only | Smoothed Round-trip Time (ms) |
| I32 hwSctpAssocRemoteIP1Rttvar | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.20 | Integer32 | read-only | Round-trip Time Variation (ms) |
| INT hwSctpAssocRemoteIP1AllowHB | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.21 | INTEGER | read-only | Whether HB can be transmitted from this address. Options: 1. no(1) -indicates that the HB can't be transmitted from this address 2. yes(2) -indicates that the HB can be transmitted from this address |
| IP hwSctpAssocRemoteIP2addr | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.22 | IpAddress | read-only | Remote IP address 2. Default: 80 |
| INT hwSctpAssocRemoteIP2State | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.23 | INTEGER | read-only | The current status of remote IP address 2 Options: 1. active(1) -indicates that the current status of remote IP address 2 is active 2. inactive(2) -indicates that the current status of remote IP address 2 is inactive |
| I32 hwSctpAssocRemoteIP2WaitAck | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.24 | Integer32 | read-only | The number of the data that is waiting for the acknowledgement by the remote SACK. -1 returns by GET means associate with IP2 does not exist. Default: 2 |
| I32 hwSctpAssocRemoteIP2Cwnd | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.25 | Integer32 | read-only | The size of the congestion window. -1 returns by GET means associate with IP2 does not exist. Default: 2 |
| I32 hwSctpAssocRemoteIP2Unfirm | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.26 | Integer32 | read-only | The size of the unacknowledged data that is transmitted on the path. -1 returns by GET means associate with IP2 does not exist. Default: 2 |
| I32 hwSctpAssocRemoteIP2Rto | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.27 | Integer32 | read-only | Retransmission Time-out(ms) -1 returns by GET means associate with IP2 does not exist. |
| I32 hwSctpAssocRemoteIP2Srtt | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.28 | Integer32 | read-only | Smoothed Round-trip Time (ms) -1 returns by GET means associate with IP2 does not exist. |
| I32 hwSctpAssocRemoteIP2Rttvar | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.29 | Integer32 | read-only | Round-trip Time Variation (ms) -1 returns by GET means associate with IP2 does not exist. |
| INT hwSctpAssocRemoteIP2AllowHB | 1.3.6.1.4.1.2011.2.6.7.6.1.12.1.30 | INTEGER | read-only | Whether HB can be sent from this address. Options: 1. no(1) -indicates that the HB can't be sent from this address 2. yes(2) -indicates that the HB can be sent from this address |
| hwIsdnIuaDuaErrStatsThresholdCfgTable | 1.3.6.1.4.1.2011.2.6.7.6.1.13 | not-accessible | Configuration table of L2UA IUA/DUA link error statistic threshold. The index of this table is hwIsdnIuaDuaErrLinkNoIndex. | |
| hwIsdnIuaDuaErrStatsThresholdCfgEntry | 1.3.6.1.4.1.2011.2.6.7.6.1.13.1 | not-accessible | Configuration table of L2UA IUA/DUA link error statistic threshold. The index of this entry is hwIsdnIuaDuaErrLinkNoIndex. | |
| I32 hwIsdnIuaDuaErrLinkNoIndex | 1.3.6.1.4.1.2011.2.6.7.6.1.13.1.1 | Integer32 | not-accessible | Link index. |
| I32 hwIsdnIuaProtocolErrAlarmThreshold | 1.3.6.1.4.1.2011.2.6.7.6.1.13.1.2 | Integer32 | read-write | Threshold of IUA error alarm. |
| I32 hwIsdnDuaProtocolErrAlarmThreshold | 1.3.6.1.4.1.2011.2.6.7.6.1.13.1.3 | Integer32 | read-write | Threshold of DUA error alarm. |
| hwMifSctpCfgParaTable | 1.3.6.1.4.1.2011.2.6.7.6.1.14 | not-accessible | This table is used to config SCTP protocol parameters of a SCTP association. The indexes of this table are hwMifSctpCfgParaProtoType and hwMifSctpCfgParaInterfaceId. | |
| hwMifSctpCfgParaEntry | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1 | not-accessible | This table is used to config SCTP protocol parameters of a SCTP association. The indexes of this entry are hwMifSctpCfgParaProtoType and hwMifSctpCfgParaInterfaceId. | |
| I32 hwMifSctpCfgParaProtoType | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.1 | Integer32 | not-accessible | Protocol Type: IUA(0),H.248(1),SIP(2); |
| I32 hwMifSctpCfgParaInterfaceId | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.2 | Integer32 | not-accessible | IUA-Link-ID/H248-Interface-ID/SIP-Interface-ID: if Protocol Type is IUA(0), this parameter for IUA LinkNo; if Protocol Type is H.248(1), this parameter for H248 interface ID; if Protocol Type is SIP(2), this parameter for SIP interface ID; |
| I32 hwMifSctpCfgParaMaxInStreamNum | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.3 | Integer32 | read-write | Maximum number of inbound streams. |
| I32 hwMifSctpCfgParaMaxOutStreamNum | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.4 | Integer32 | read-write | Maximum number of outbound streams |
| I32 hwMifSctpCfgParaRtoMin | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.5 | Integer32 | read-only | The minimum RTO. Default: 1000 Unit: millisecond |
| I32 hwMifSctpCfgParaRtoMax | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.6 | Integer32 | read-write | The maximum RTO. Default: 3000(Mg interface),60000(Iua-Link) Unit: millisecond |
| I32 hwMifSctpCfgParaRtoInit | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.7 | Integer32 | read-write | The initial RTO. Unit: millisecond |
| I32 hwMifSctpCfgParaValidCookieLife | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.8 | Integer32 | read-write | Cookie lifecycle. Unit: millisecond |
| I32 hwMifSctpCfgParaMaxInitRetrans | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.9 | Integer32 | read-write | The maximum retransmit attempts of INIT |
| I32 hwMifSctpCfgParaRtoAlpha | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.10 | Integer32 | read-write | Parameter of RTO Alpha |
| I32 hwMifSctpCfgParaRtoBeta | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.11 | Integer32 | read-write | Parameter of RTO Beta |
| I32 hwMifSctpCfgParaAssocMaxRetrans | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.12 | Integer32 | read-write | The maximum retransmit attempts in a association |
| I32 hwMifSctpCfgParaPathMaxRetrans | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.13 | Integer32 | read-write | The maximum Retransmit attempts in a path |
| I32 hwMifSctpCfgParaNoCongestionLevel | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.14 | Integer32 | read-write | Parameter of no-congestion level |
| I32 hwMifSctpCfgParaLowCongestionLevel | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.15 | Integer32 | read-write | Parameter of low-congestion level |
| I32 hwMifSctpCfgParaHighCongestionLevel | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.16 | Integer32 | read-write | Parameter of high-congestion level |
| I32 hwMifSctpCfgParaHbInterval | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.17 | Integer32 | read-write | Heartbeat interval. For Mg interface, 10000~120000 is valid. For Iua-Link, 2000~120000 is valid. Default: 10000(Mg interface),30000(Iua-Link) Unit: millisecond |
| INT hwMifSctpCfgParaSendChecksum | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.18 | INTEGER | read-only | Sending the checksum. Options: 1. no(1) -indicates that the checksum is not Sending 2. yes(2) -indicates that the checksum is Sending |
| INT hwMifSctpCfgParaRecvChecksum | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.19 | INTEGER | read-only | Receiving the checksum. Options: 1. no(1) -indicates that the checksum is not Receiving 2. yes(2) -indicates that the checksum is Receiving |
| INT hwMifSctpCfgParaChecksumArith | 1.3.6.1.4.1.2011.2.6.7.6.1.14.1.20 | INTEGER | read-write | Checksum algorithm. Options: 1. adler32(1) -indicates that Checksum algorithm is ADLER32 2. crc32(2) -indicates that Checksum algorithm is CRC32 |
| hwMifSctpRunningParaTable | 1.3.6.1.4.1.2011.2.6.7.6.1.15 | not-accessible | This table is used to query current running SCTP protocol parameter. The indexes of this table are hwMifSctpRunningParaProtoType and hwMifSctpRunningParaInterfaceId. | |
| hwMifSctpRunningParaEntry | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1 | not-accessible | This table is used to query current running SCTP protocol parameter. The indexes of this entry are hwMifSctpRunningParaProtoType and hwMifSctpRunningParaInterfaceId. | |
| I32 hwMifSctpRunningParaProtoType | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.1 | Integer32 | not-accessible | Protocol Type: IUA(0),H.248(1),SIP(2); |
| I32 hwMifSctpRunningParaInterfaceId | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.2 | Integer32 | not-accessible | IUA-Link-ID/H248-Interface-ID/SIP-Interface-ID: if Protocol Type is IUA(0), this parameter for IUA LinkNo; if Protocol Type is H.248(1), this parameter for H248 interface ID; if Protocol Type is SIP(2), this parameter for SIP interface ID; |
| I32 hwMifSctpRunningParaMaxInStreamNum | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.3 | Integer32 | read-only | Maximum number of inbound streams. Default: 33 |
| I32 hwMifSctpRunningParaMaxOutStreamNum | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.4 | Integer32 | read-only | Maximum number of outbound streams. Default: 33 |
| I32 hwMifSctpRunningParaRtoMin | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.5 | Integer32 | read-only | The minimum RTO. Default: 1000 Unit: millisecond |
| I32 hwMifSctpRunningParaRtoMax | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.6 | Integer32 | read-only | The maximum RTO. For Mg interface, default value 3000. For Iua-Link, default value 60000. Unit: millisecond |
| I32 hwMifSctpRunningParaRtoInit | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.7 | Integer32 | read-only | The initial RTO. Default: 1000 Unit: millisecond |
| I32 hwMifSctpRunningParaValidCookieLife | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.8 | Integer32 | read-only | Cookie lifecycle. Default: 60000 Unit: millisecond |
| I32 hwMifSctpRunningParaMaxInitRetrans | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.9 | Integer32 | read-only | The maximum retransmit attempts of INIT. Default: 8 |
| I32 hwMifSctpRunningParaRtoAlpha | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.10 | Integer32 | read-only | Parameter of RTO Alpha. Default: 12 |
| I32 hwMifSctpRunningParaRtoBeta | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.11 | Integer32 | read-only | Parameter of RTO Beta. Default: 25 |
| I32 hwMifSctpRunningParaAssocMaxRetrans | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.12 | Integer32 | read-only | The maximum retransmit attempts in a association. Default: 10 |
| I32 hwMifSctpRunningParaPathMaxRetrans | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.13 | Integer32 | read-only | The maximum Retransmit attempts in a path. Default: 5 |
| I32 hwMifSctpRunningParaNoCongestionLevel | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.14 | Integer32 | read-only | Parameter of no-congestion level Default: 40 |
| I32 hwMifSctpRunningParaLowCongestionLevel | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.15 | Integer32 | read-only | Parameter of low-congestion level Default: 60 |
| I32 hwMifSctpRunningParaHighCongestionLevel | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.16 | Integer32 | read-only | Parameter of high-congestion level. Default: 80 |
| I32 hwMifSctpRunningParaHbInterval | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.17 | Integer32 | read-only | Heartbeat interval. For Mg interface, default value 10000. Default: 30000 Unit: millisecond |
| INT hwMifSctpRunningParaSendChecksum | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.18 | INTEGER | read-only | Sending the checksum. Options: 1. no(1) -indicates that the checksum is not Sending 2. yes(2) -indicates that the checksum is Sending Default: 2 |
| INT hwMifSctpRunningParaRecvChecksum | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.19 | INTEGER | read-only | Receiving the checksum. Options: 1. no(1) -indicates that the checksum is not Receiving 2. yes(2) -indicates that the checksum is Receiving Default: 2 |
| INT hwMifSctpRunningParaChecksumArith | 1.3.6.1.4.1.2011.2.6.7.6.1.15.1.20 | INTEGER | read-only | Checksum algorithm. Options: 1. adler32(1) -indicates that Checksum algorithm is ADLER32 2. crc32(2) -indicates that Checksum algorithm is CRC32 Default: 2 |
| hwSctpGlobalParaTable | 1.3.6.1.4.1.2011.2.6.7.6.1.16 | |||
| INT hwSctpGlobalParaSendChecksum | 1.3.6.1.4.1.2011.2.6.7.6.1.16.1 | INTEGER | read-write | Sending the checksum: Options: 1. no(1) -indicates that the checksum is not Sending 2. yes(2) -indicates that the checksum is Sending Default: 2 |
| INT hwSctpGlobalParaRecvChecksum | 1.3.6.1.4.1.2011.2.6.7.6.1.16.2 | INTEGER | read-write | Receiving the checksum. Options: 1. no(1) -indicates that the checksum is not Receiving 2. yes(2) -indicates that the checksum is Receiving Default: 2 |
| hwIASSigtranTrapsVbOids | 1.3.6.1.4.1.2011.2.6.7.6.2 | |||
| hwIASSigtranTraps | 1.3.6.1.4.1.2011.2.6.7.6.3 | |||
| hwIASSigtranCommonTraps | 1.3.6.1.4.1.2011.2.6.7.6.3.1 | |||
| hwIASSigtranL2uaTraps | 1.3.6.1.4.1.2011.2.6.7.6.3.1.1 | |||
| hwIASSigtranAlarmTraps | 1.3.6.1.4.1.2011.2.6.7.6.3.2 | |||
| hwIASSigtranL2uaAlarmTraps | 1.3.6.1.4.1.2011.2.6.7.6.3.2.1 | |||
| NTF hwIASSigtranL2uaLinkUnestTrap | 1.3.6.1.4.1.2011.2.6.7.6.3.2.1.0.1 | This notification indicates that the L2UA link is not established. | ||
| NTF hwIASSigtranL2uaLinkActiveTrap | 1.3.6.1.4.1.2011.2.6.7.6.3.2.1.0.2 | This notification indicates that the L2UA link is actived. | ||
| NTF hwIASSigtranL2uaLinksetDownTrap | 1.3.6.1.4.1.2011.2.6.7.6.3.2.1.0.3 | This notification indicates that the L2UA linkset is not activated. | ||
| NTF hwIASSigtranL2uaLinksetActiveTrap | 1.3.6.1.4.1.2011.2.6.7.6.3.2.1.0.4 | This notification indicates that the L2UA linkset is activated. |
RFC description
Huawei SIGTRAN management MIB for signaling transport protocols including SCTP and L2UA configuration.
Start monitoring Huawei SIGTRAN signaling gateway / media gateway controller with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.