HUAWEI-MPLSLSR-EXT-MIB

All MIBs › HUAWEI-MPLSLSR-EXT-MIB

Organization: Huawei Technologies Co.,Ltd.

Last Updated: 2013-09-24

Category: MPLS and Traffic Engineering, Vendor: Huawei

Description: Huawei MPLS LSR extensions MIB providing Huawei-specific extensions to standard MPLS LSR management objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-MPLSLSR-EXT-MIB?

HUAWEI-MPLSLSR-EXT-MIB is a Huawei extension to the standards-track MPLS-LSR-STD-MIB, adding Huawei-specific MPLS Label Switch Router configuration and status objects for basic MPLS enablement and label advertisement policy. It covers global MPLS setup (hwMplsLsrId, hwMplsCapabilityConfig, hwMplsLabelAdvertise — explicit/implicit/non-null label policy), MPLS BFD fast-failure-detection parameters (hwMplsBfdCapabilityConfig, hwMplsBfdMinTx/MinRx, hwMplsBfdDetectMultiplier, and trigger policy via hwMplsBfdTrigger/hwMplsFecListTable), per-interface MPLS MTU and enablement (hwMplsInterfaceTable), static LDP fast-reroute backup paths (hwLdpStaticFrrInterfaceTable), LDP virtual tunnel status (hwLdpVirtualTunnelTable, with up/down/testing state and associated notifications hwMplsLdpVirtualTunnelUp/Down), and static LSP provisioning (hwMplsStaticLspTable, covering ingress/transit/egress/ingress-bind-tunnel LSP types with in/out labels and next-hop/destination). Monitoring this MIB reveals whether MPLS BFD sessions and LDP virtual tunnels are up, whether static LSPs and FRR backup paths are correctly provisioned, and whether label advertisement policy matches intent — all of which affect MPLS forwarding correctness and failover speed, and it depends on the underlying MPLS-LSR-STD-MIB framework it extends and on IF-MIB for interface indexing. It is deployed on Huawei MPLS-capable routers, and network engineers perform a HUAWEI-MPLSLSR-EXT-MIB download to load it into their MIB browser when managing these routers.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-MPLSLSR-EXT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei routers (MPLS Label Switch Router extensions)

Monitoring Examples

An operator polls hwLdpVirtualTunnelTable to check hwLdpVirtualStatus for a given tunnel index; a status of down accompanied by an hwMplsLdpVirtualTunnelDown notification would indicate the LDP virtual tunnel has failed and traffic mapped to it is at risk of being dropped.

What Can Be Monitored

MPLS LSR ID and capability enablement state
label advertisement policy configuration
MPLS BFD session parameters and trigger policy
LDP virtual tunnel up/down status
static LDP FRR backup interface entries
static LSP provisioning (labels, next hop, destination)

Imported Objects

From HUAWEI-MIB

hwDatacomm

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex

From MPLS-TC-STD-MIB

MplsLabel

From P-BRIDGE-MIB

EnabledStatus

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwMplsLsrExtMIB	1.3.6.1.4.1.2011.5.25.182			This MIB provides management of MPLS basic configurations. It is an extension of MPLS-LSR-STD-MIB.
hwMplsLsrExtObject	1.3.6.1.4.1.2011.5.25.182.1
IP hwMplsLsrId	1.3.6.1.4.1.2011.5.25.182.1.1	IpAddress	read-write	This object indicates the configuration of the MPLS LSR ID. Before the MPLS capability is enabled, the MPLS LSR ID must be configured. After the MPLS capability is enabled, the MPLS LSR ID cannot be modified or deleted. If the MPLS LSR ID is set as 0.0.0.0, it indicates that the MPLS LSR ID is deleted. The MPLS LSR ID and the MPLS capability cannot be configured together.
ENA hwMplsCapabilityConfig	1.3.6.1.4.1.2011.5.25.182.1.2	EnabledStatus	read-write	This object indicates the configuration or deletion of the MPLS capability. Before the MPLS capability is enabled, the MPLS LSR ID must be configured.
INT hwMplsLabelAdvertise	1.3.6.1.4.1.2011.5.25.182.1.3	INTEGER	read-write	This object indicates the way to configure label advertisement policy. By default, the label advertisement policy is implicitnull. Before the label advertisement policy is configured, MPLS capability must be enabled. Options: 1. explicitNull(1) -indicates that the label advertisement policy is explicitNull. 2. implicitNull(2) -indicates that the label advertisement policy is implicitNull. 3. nonNull(3) -indicates that the label advertisement policy is nonNull. Default: implicitNull(2)
I32 hwMplsStatisticsIntervalTimer	1.3.6.1.4.1.2011.5.25.182.1.4	Integer32	read-write	This object indicates the value of the MPLS statistics timer. Range: 30-65535 Default: 0 Unit: seconds
ENA hwMplsBfdCapabilityConfig	1.3.6.1.4.1.2011.5.25.182.1.5	EnabledStatus	read-write	This object indicates the configuration or deletion of the MPLS BFD capability. Before the MPLS BFD function is enabled, you must enable the MPLS capability and BFD capability.
I32 hwMplsBfdMinTx	1.3.6.1.4.1.2011.5.25.182.1.6	Integer32	read-write	This object indicates the minimum forwarding period. If the minimum forwarding period is set as 0 seconds, it indicates that the minimum forwarding period returns to the default value.
I32 hwMplsBfdMinRx	1.3.6.1.4.1.2011.5.25.182.1.7	Integer32	read-write	This object indicates the minimum receiving period. If the minimum receiving period is set as 0 seconds, it indicates that the minimum receiving period returns to the default value.
I32 hwMplsBfdDetectMultiplier	1.3.6.1.4.1.2011.5.25.182.1.8	Integer32	read-write	This object indicates the value of the detect multiplier. If the value of the detect multiplier is set as 0, it indicates that the value returns to the default value.
STR hwMplsFecListName	1.3.6.1.4.1.2011.5.25.182.1.9	DisplayString	read-write	This object indicates the name of the FEC LIST. The name of the FEC LIST is globally unique, with a valid length from 1 to 31 characters. If the character length is 0, it indicates that the FEC LIST is deleted. Furthermore, the FEC LIST cannot be modified, and you can only delete the FEC LIST and then create a new one. If the FEC LIST is used by others, you need to cancel the usage and then delete the FEC LIST. Range: 1-31
INT hwMplsBfdTrigger	1.3.6.1.4.1.2011.5.25.182.1.10	INTEGER	read-write	This object indicates the MPLS BFD triggering policy. By using this object, you can also specify the next hop and the outgoing interface. To configure the MPLS BFD triggering policy, you must enable MPLS and BFD in advance. In addition, this MPLS BFD triggering policy cannot be modified, and you can only delete the policy and then create a new one. Options: 1. triggerHost(1) -indicates that the MPLS BFD triggering policy was configured as host. 2. triggerFeclist(2) -indicates that the MPLS BFD triggering policy was configured as FEC list. 3. disabled(3) -indicates that the MPLS BFD triggering policy was not configured. Default: triggerHost(1)
IP hwMplsBfdTriggerNextHop	1.3.6.1.4.1.2011.5.25.182.1.11	IpAddress	read-write	This object indicates the next hop when the MPLS BFD trigger policy is configured as host. The next hop and the outgoing interface can be specified at the same time.
U32 hwMplsBfdTriggerInterface	1.3.6.1.4.1.2011.5.25.182.1.12	Unsigned32	read-write	This object indicates the outgoing interface when the MPLS BFD trigger policy is configured as host. The next hop and the outgoing interface can be specified at the same time. In addition, you can get the correct interface index based on the ifIndex of ifTable.
STR hwMplsBfdTriggerFecListName	1.3.6.1.4.1.2011.5.25.182.1.13	DisplayString	read-write	This object indicates the FEC list when the MPLS BFD trigger policy is configured. The valid length of the FEC list ranges from 1 to 31 characters. If the specified FEC list does not exist, or the specified FEC list contains no FEC node, no LSP can be triggered. Range: 1-31
U32 hwLdpVirtualTunnelFEC	1.3.6.1.4.1.2011.5.25.182.1.14	Unsigned32	accessible-for-notify	This object indicates the LDP virtual tunnel FEC.
ENA hwMplsBgpBfdCapabilityConfig	1.3.6.1.4.1.2011.5.25.182.1.15	EnabledStatus	read-write	This object indicates the configuration or deletion of the MPLS BGP BFD capability. Before the MPLS BGP BFD function is enabled, you must enable the MPLS capability and BFD capability.
I32 hwMplsBgpBfdMinTx	1.3.6.1.4.1.2011.5.25.182.1.16	Integer32	read-write	This object indicates the minimum forwarding period. If the minimum forwarding period is set as 0 seconds, it indicates that the minimum forwarding period returns to the default value.
I32 hwMplsBgpBfdMinRx	1.3.6.1.4.1.2011.5.25.182.1.17	Integer32	read-write	This object indicates the minimum receiving period. If the minimum receiving period is set as 0 seconds, it indicates that the minimum receiving period returns to the default value.
I32 hwMplsBgpBfdDetectMultiplier	1.3.6.1.4.1.2011.5.25.182.1.18	Integer32	read-write	This object indicates the value of the detect multiplier. If the value of the detect multiplier is set as 0, it indicates that the value returns to the default value.
INT hwMplsBgpBfdTriggerTunnel	1.3.6.1.4.1.2011.5.25.182.1.19	INTEGER	read-write	This object indicates the MPLS BGP BFD triggering policy. To configure the MPLS BGP BFD triggering policy, you must enable MPLS and BFD in advance. Options: 1. triggerHost(1) -indicates that the MPLS BGP BFD triggering policy was configured as host. 2. triggerIpPrefix(2) -indicates that the MPLS BGP BFD triggering policy was configured as Ip Prefix. 3. disabled(3) -indicates that the MPLS BGP BFD triggering policy was not configured. Default: disabled(3)
STR hwMplsBgpBfdTriggerTunnelIpprefix	1.3.6.1.4.1.2011.5.25.182.1.20	DisplayString	read-write	This object indicates the IP Prefix name when the MPLS BGP BFD trigger policy is configured. The valid length of the IP prefix name ranges from 1 to 169 characters. Range: 1-169
hwMplsFecListTable	1.3.6.1.4.1.2011.5.25.182.1.50		not-accessible	This table is used to configure or delete MPLS FEC Node. The indexes of this table are hwMplsFecNodeIpAddress, hwMplsFecNodeInterface, and hwMplsFecNodeNextHop.
hwMplsFecListEntry	1.3.6.1.4.1.2011.5.25.182.1.50.1		not-accessible	An FEC node entry of FEC list table. It can be created, or deleted. The indexes of this entry are hwMplsFecNodeIpAddress, hwMplsFecNodeInterface, and hwMplsFecNodeNextHop.
IP hwMplsFecNodeIpAddress	1.3.6.1.4.1.2011.5.25.182.1.50.1.2	IpAddress	not-accessible	This object indicates the IP address of the specified FEC node.
U32 hwMplsFecNodeInterface	1.3.6.1.4.1.2011.5.25.182.1.50.1.3	Unsigned32	not-accessible	This object indicates the outgoing interface of the FEC node. You can get the correct interface index based on the ifIndex of ifTable.
IP hwMplsFecNodeNextHop	1.3.6.1.4.1.2011.5.25.182.1.50.1.4	IpAddress	not-accessible	This object indicates the next hop of the FEC node.
ROW hwMplsFecListRowStatus	1.3.6.1.4.1.2011.5.25.182.1.50.1.51	RowStatus	read-create	This object indicates whether one entry of FEC list table is created or destroyed. The value of the object can be CreatAndGo or Destroy. If the value is set as CreatAndGo, and the entry is created in hwFecListTable, the status of the object will change into active.
hwMplsInterfaceTable	1.3.6.1.4.1.2011.5.25.182.1.51		not-accessible	This table is used to configure or delete the MPLS capability on the interface. The index of this table is hwMplsInterfaceIndex.
hwMplsInterfaceEntry	1.3.6.1.4.1.2011.5.25.182.1.51.1		not-accessible	An entry of the MPLS interface table, used to display and configure features on the MPLS-supporting interface. The index of this entry is hwMplsInterfaceIndex.
NUM hwMplsInterfaceIndex	1.3.6.1.4.1.2011.5.25.182.1.51.1.1	InterfaceIndex	not-accessible	This object indicates the interface index. You can get the correct interface index based on the ifIndex of ifTable.
I32 hwMplsMtu	1.3.6.1.4.1.2011.5.25.182.1.51.1.11	Integer32	read-create	This object indicates the MPLS MTU of an interface. If the value of the MPLS MTU is set as 0, it indicates that the MPLS MTU is deleted.
ROW hwMplsInterfaceRowStatus	1.3.6.1.4.1.2011.5.25.182.1.51.1.51	RowStatus	read-create	This object indicates whether one entry is created or deleted in hwMplsInterfaceTable. The value of the object can be CreatAndGo and Destroy. When the value is set as CreatAndGo, and the entry is created, the status of the object will change into active.
hwLdpStaticFrrInterfaceTable	1.3.6.1.4.1.2011.5.25.182.1.52		not-accessible	This table is used to configure or delete static LDP FRR entries on the interface. The indexes of this table are hwMplsInterfaceIndex and hwLdpStaticFrrPriority.
hwLdpStaticFrrInterfaceEntry	1.3.6.1.4.1.2011.5.25.182.1.52.1		not-accessible	This entry is used to display and configure the FRR-supporting interface. The indexes of this entry are hwMplsInterfaceIndex and hwLdpStaticFrrPriority.
I32 hwLdpStaticFrrPriority	1.3.6.1.4.1.2011.5.25.182.1.52.1.1	Integer32	not-accessible	This object indicates the priority of a static FRR entry.
IP hwLdpStaticFrrNextHop	1.3.6.1.4.1.2011.5.25.182.1.52.1.11	IpAddress	read-create	This object indicates the next hop of the static FRR.
STR hwLdpStaticFrrIpPrefix	1.3.6.1.4.1.2011.5.25.182.1.52.1.12	DisplayString	read-create	This object indicates the IP prefix policy. The valid prefix length ranges from 1 to 169 characters. When the length is 0, it indicates that the policy is deleted. Range: 1-169
ROW hwLdpStaticFrrInterfaceRowStatus	1.3.6.1.4.1.2011.5.25.182.1.52.1.51	RowStatus	read-create	This object indicates whether one entry is created or deleted in hwLdpStaticFrrInterfaceTable. The value of the object can be CreatAndGo or Destroy. When the value is set as CreatAndGo, and the entry is created, the status of the object will change into active.
hwLdpVirtualTunnelTable	1.3.6.1.4.1.2011.5.25.182.1.53		not-accessible	This table specifies LDP virtual tunnel information. The index of this table is hwLdpVirtualTunnelIndex.
hwLdpVirtualTunnelEntry	1.3.6.1.4.1.2011.5.25.182.1.53.1		not-accessible	An entry of the virtual tunnel table, used to display the features associated with the virtual tunnel. The index of this entry is hwLdpVirtualTunnelIndex.
U32 hwLdpVirtualTunnelIndex	1.3.6.1.4.1.2011.5.25.182.1.53.1.1	Unsigned32	not-accessible	This object indicates the LDP virtual tunnel index.
INT hwLdpVirtualStatus	1.3.6.1.4.1.2011.5.25.182.1.53.1.2	INTEGER	read-only	The status of this LDP virtual tunnel. Options: 1. up(1) -indicates that the status of this LDP virtual tunnel is Up. 2. down(2) -indicates that the status of this LDP virtual tunnel is Down. 3. testing(3) -indicates that the status of this LDP virtual tunnel is testing, this is, in some test mode. Default: up(1)
OCT hwLdpXcIndexArray	1.3.6.1.4.1.2011.5.25.182.1.53.1.3	OCTET STRING	read-only	This object indicates the xc index of the members of the LDP virtual tunnel.
OCT hwLdpOutSegmentIndexArray	1.3.6.1.4.1.2011.5.25.182.1.53.1.4	OCTET STRING	read-only	This object indicates the outsegment index of the members of the LDP virtual tunnel.
hwLdpVirtualTunnelTrap	1.3.6.1.4.1.2011.5.25.182.1.54
NTF hwMplsLdpVirtualTunnelUp	1.3.6.1.4.1.2011.5.25.182.1.54.1			A trap is sent when an LDP virtual tunnel goes Up.
NTF hwMplsLdpVirtualTunnelDown	1.3.6.1.4.1.2011.5.25.182.1.54.2			A trap is sent when an LDP virtual tunnel goes Down.
hwMplsStaticLspTable	1.3.6.1.4.1.2011.5.25.182.1.55		not-accessible	This table is used to create or delete static LSP configurations. The index of this table is hwMplsStaticLspName.
hwMplsStaticLspEntry	1.3.6.1.4.1.2011.5.25.182.1.55.1		not-accessible	The entry is used to show or configure static LSP. The index of this entry is hwMplsStaticLspName.
STR hwMplsStaticLspName	1.3.6.1.4.1.2011.5.25.182.1.55.1.1	DisplayString	not-accessible	This object indicates the name of static LSP.
INT hwMplsStaticLspType	1.3.6.1.4.1.2011.5.25.182.1.55.1.11	INTEGER	read-create	This object is used to identify the type of static LSP. Options: 1. ingress(1) -indicates that the type of the static LSP is ingress. 2. transit(2) -indicates that the type of the static LSP is transit. 3. egress(3) -indicates that the type of the static LSP is egress. 4. ingressBindTunnel(4) -indicates that the type of the static LSP is ingress-bind-tunnel.
U32 hwMplsStaticLspInIntfIndex	1.3.6.1.4.1.2011.5.25.182.1.55.1.12	Unsigned32	read-create	This object indicates the incoming-interface index.
MPL hwMplsStaticLspInLabel	1.3.6.1.4.1.2011.5.25.182.1.55.1.13	MplsLabel	read-create	This object indicates the in-label.
IP hwMplsStaticLspLsrId	1.3.6.1.4.1.2011.5.25.182.1.55.1.14	IpAddress	read-create	This object indicates the LSR ID of ingress static LSP.
U32 hwMplsStaticLspTunnelID	1.3.6.1.4.1.2011.5.25.182.1.55.1.15	Unsigned32	read-create	This object indicates the Tunnel ID of ingress static LSP.
IP hwMplsStaticLspNextHop	1.3.6.1.4.1.2011.5.25.182.1.55.1.16	IpAddress	read-create	This object indicates the nexthop of static LSP.
U32 hwMplsStaticLspOutIntfIndex	1.3.6.1.4.1.2011.5.25.182.1.55.1.17	Unsigned32	read-create	This object indicates the outgoing-interface index.
MPL hwMplsStaticLspOutLabel	1.3.6.1.4.1.2011.5.25.182.1.55.1.18	MplsLabel	read-create	This object indicates the out-label.
IP hwMplsStaticLspDestAddr	1.3.6.1.4.1.2011.5.25.182.1.55.1.19	IpAddress	read-create	This object indicates the destination.
U32 hwMplsStaticLspMaskLen	1.3.6.1.4.1.2011.5.25.182.1.55.1.20	Unsigned32	read-create	This object indicates the mask length.
ROW hwMplsStaticLspRowStatus	1.3.6.1.4.1.2011.5.25.182.1.55.1.51	RowStatus	read-create	This object indicates whether one entry is created or deleted in hwMplsStaticLspTable. The value of the object can be CreateAndGo or Destroy. When the value is set as CreateAndGo, and the entry is created, the status of the object will change into active.
hwMplsLsrExtConformance	1.3.6.1.4.1.2011.5.25.182.2
hwMplsLsrExtCompliances	1.3.6.1.4.1.2011.5.25.182.2.1
hwMplsModuleCompliance	1.3.6.1.4.1.2011.5.25.182.2.1.1			hwMplsModuleCompliance
hwMplsLsrExtGroup	1.3.6.1.4.1.2011.5.25.182.2.2
hwMplsBasicGroup	1.3.6.1.4.1.2011.5.25.182.2.2.1			Objects required for MPLS basic configuration management.
hwMplsBfdGroup	1.3.6.1.4.1.2011.5.25.182.2.2.2			Objects required for MPLS BFD configuration management.
hwLdpStaticFrrGroup	1.3.6.1.4.1.2011.5.25.182.2.2.3			Objects required for LDP static FRR configuration management.
hwMplsInterfaceGroup	1.3.6.1.4.1.2011.5.25.182.2.2.4			Objects required for MPLS configuration management on interface.
hwMplsLdpVirtualTunnelGroup	1.3.6.1.4.1.2011.5.25.182.2.2.5			Objects required for LDP virtual tunnel management.
hwMplsLdpVirtualTunnelNotificationGroup	1.3.6.1.4.1.2011.5.25.182.2.2.6			Notification information about LDP virtual tunnel.
hwMplsStaticLspGroup	1.3.6.1.4.1.2011.5.25.182.2.2.7			Objects required for static LSP configuration management.
hwMplsBgpBfdGroup	1.3.6.1.4.1.2011.5.25.182.2.2.8			Objects required for MPLS BGP BFD configuration management.

RFC description

HUAWEI MPLS Label Switching Router extension for MPLS configuration and BGP/BFD management.

Start monitoring Huawei routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-MPLSLSR-EXT-MIB

What Is HUAWEI-MPLSLSR-EXT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description