All MIBs › HUAWEI-IPFPM-MIB
Organization: Huawei Technologies Co.,Ltd.
Last Updated: 2015-10-13
Category: Technology: OAM, Vendor: Huawei
Description: Huawei IPFPM (IP Flow Performance Measurement) MIB for measuring packet loss, delay, and jitter on IP flows per Y.1731 and RFC 6374.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-IPFPM-MIB?
HUAWEI-IPFPM-MIB is a Huawei enterprise MIB implementing IP Flow Performance Measurement (IPFPM), a framework aligned with ITU-T Y.1731 and IETF RFC 6374 for measuring packet loss, delay, and jitter on specific IP flows using cooperating roles: a Measurement Control Point (MCP), Data Collecting Points (DCP), and Target Logic Points (TLP). It exposes objects to configure measurement sessions between these roles and to retrieve the resulting per-flow performance statistics collected by the TLPs and reported up through the DCPs to the MCP. Its monitoring focus is performance/SLA-oriented: per-flow packet-loss ratio, one-way/two-way delay, and jitter measurements that reveal degrading network paths affecting latency-sensitive services. It explicitly builds on the ITU-T Y.1731 and IETF RFC 6374 performance-measurement standards for its underlying measurement model. It is deployed on Huawei carrier routers/switches in networks carrying performance-sensitive traffic (e.g., mobile backhaul, MPLS/VPN services) where operators need to verify SLA compliance for specific IP flows. Engineers can download the HUAWEI-IPFPM-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-IPFPM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei carrier routers/switches supporting IPFPM
Monitoring Examples
No object names were captured for this module, so specific OIDs cannot be cited; based on the module description, an admin would typically configure a measurement session between an MCP and TLP and then poll the resulting per-flow packet-loss, delay, and jitter statistics to detect an SLA-violating IP flow experiencing congestion or a failing path.
What Can Be Monitored
- per-flow packet loss ratio
- per-flow delay/latency
- per-flow jitter
- measurement session status
This MIB depends on
Related MIBs
Imported Objects
From HUAWEI-MIB
| hwDatacomm | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hwIpfpmMib | 1.3.6.1.4.1.2011.5.25.316 | This MIB describes objects to manage IPFPM (IP Flow Performance Measurement). IPFPM provides a method for IP flow performance measurement, in which MCP (Measurement Control Point),DCP (Data Collecting Point) and TLP (Target Logic Point) are three kinds of roles working together. TLP is responsible for implementing measurement and generating the measurement data. DCP manages TLPs and get measurement data from them to report to MCP. MCP works as the control role to collect and calculate the measurement data that DCP reported. | ||
| hwIpfpmMcpObjects | 1.3.6.1.4.1.2011.5.25.316.1 | |||
| hwIpfpmMcpConfiguration | 1.3.6.1.4.1.2011.5.25.316.1.1 | |||
| hwIpfpmMcpGlobalTable | 1.3.6.1.4.1.2011.5.25.316.1.1.1 | |||
| HWE hwIpfpmMcpEnable | 1.3.6.1.4.1.2011.5.25.316.1.1.1.1 | HWEnabledStatus | read-write | This object indicates that the MCP (Measurement Control Point) function is 'enabled(1)' or 'disabled(2)'. |
| IP hwIpfpmMcpId | 1.3.6.1.4.1.2011.5.25.316.1.1.1.2 | IpAddress | read-write | The value of this object indicates the identification of MCP. The value 0.0.0.0 represents that it is not configured. |
| I32 hwIpfpmMcpUdpPort | 1.3.6.1.4.1.2011.5.25.316.1.1.1.3 | Integer32 | read-write | The value of this object indicates the port that MCP listens on as the server. |
| hwIpfpmMcpAuthTable | 1.3.6.1.4.1.2011.5.25.316.1.1.4 | not-accessible | The table contains attribute of MCP authenticaiton. | |
| hwIpfpmMcpAuthEntry | 1.3.6.1.4.1.2011.5.25.316.1.1.4.1 | not-accessible | IPFPM authenticaiton configuration information. | |
| I32 hwIpfpmMcpAuthKeyId | 1.3.6.1.4.1.2011.5.25.316.1.1.4.1.1 | Integer32 | not-accessible | Identification of the authentication key. |
| HWI hwIpfpmMcpAuthType | 1.3.6.1.4.1.2011.5.25.316.1.1.4.1.2 | HWIpfpmAuthType | read-create | Authentication type of the key. The enumeration 'hmac-sha256(1)' represents the password is sent after being encrypted through hmac-sha256. By default, authentication is not configured. |
| OCT hwIpfpmMcpAuthKey | 1.3.6.1.4.1.2011.5.25.316.1.1.4.1.3 | OCTET STRING | read-create | The password used as an IPFPM authentication key. |
| ROW hwIpfpmMcpAuthRowStatus | 1.3.6.1.4.1.2011.5.25.316.1.1.4.1.4 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| hwIpfpmMcpInstTable | 1.3.6.1.4.1.2011.5.25.316.1.1.5 | not-accessible | The table contains attribute of MCP test instances. | |
| hwIpfpmMcpInstEntry | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1 | not-accessible | IPFPM configuration information for a particular MCP test instance. | |
| I32 hwIpfpmMcpInstId | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.1 | Integer32 | not-accessible | Identification of the test instance. |
| OCT hwIpfpmMcpInstDesc | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.2 | OCTET STRING | read-create | Description of the test instance. if the string length is 0, it represents that it is not configured. |
| I32 hwIpfpmMcpLossRatioUpThres | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.3 | Integer32 | read-create | This value divided by 1000000 is the upper threshold of loss ratio(%) for alarm. The value 0 represents that it is not configured, and the alarm is not enabled. |
| I32 hwIpfpmMcpLossRatioLowThres | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.4 | Integer32 | read-create | This value divided by 1000000 is the lower threshold of loss ratio(%) for alarm recovery. The value 0 represents that it is not configured, and the alarm is not enabled. |
| I32 hwIpfpmMcpOneDelayUpThres | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.5 | Integer32 | read-create | Upper threshold of one-way delay(us) for alarm. The value 0 represents that it is not configured, and the alarm is not enabled. |
| I32 hwIpfpmMcpOneDelayLowThres | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.6 | Integer32 | read-create | Lower threshold of one-way delay(us) for alarm recovery. The value 0 represents that it is not configured, and the alarm is not enabled. |
| I32 hwIpfpmMcpTwoDelayUpThres | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.7 | Integer32 | read-create | Upper threshold of two-way delay(us) for alarm. The value 0 represents that it is not configured, and the alarm is not enabled. |
| I32 hwIpfpmMcpTwoDelayLowThres | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.8 | Integer32 | read-create | Lower threshold of two-way delay(us) for alarm recovery. The value 0 represents that it is not configured, and the alarm is not enabled. |
| HWE hwIpfpmMcpMeasureEnable | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.9 | HWEnabledStatus | read-create | This object indicates that the MCP instance measure function is 'enabled(1)' or 'disabled(2)'. |
| ROW hwIpfpmMcpInstRowStatus | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.10 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| HWI hwIpfpmMcpInstType | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.11 | HWIpfpmInstType | read-create | This object indicates that the MCP instance type. 'unicast(0)' means unicast measurement instance. 'multicastsrc(1)' means multicast measurement source instance. 'multicastrecv(2)' means multicast measurement receiver instance. |
| I32 hwIpfpmMcpSourceInstId | 1.3.6.1.4.1.2011.5.25.316.1.1.5.1.12 | Integer32 | read-create | This object indicates the source instance of multicastrecv. This object is only valid when hwIpfpmMcpInstType is 'multicastrecv(2)'. We can ingore this object value when hwIpfpmMcpInstType is not 'multicastrecv(2)'. |
| hwIpfpmMcpDcpTable | 1.3.6.1.4.1.2011.5.25.316.1.1.6 | not-accessible | The table describe the DCPs belonging to MCP test instances. | |
| hwIpfpmMcpDcpEntry | 1.3.6.1.4.1.2011.5.25.316.1.1.6.1 | not-accessible | IPFPM DCPs information for a particular MCP test instance. | |
| IP hwIpfpmMcpDcpId | 1.3.6.1.4.1.2011.5.25.316.1.1.6.1.1 | IpAddress | not-accessible | Identification of DCP which belongs to the test instance. |
| ROW hwIpfpmMcpDcpRowStatus | 1.3.6.1.4.1.2011.5.25.316.1.1.6.1.2 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| hwIpfpmMcpAchTable | 1.3.6.1.4.1.2011.5.25.316.1.1.7 | not-accessible | The table describe the ACHs(Atomic Closed Hop) belonging to MCP test instances. | |
| hwIpfpmMcpAchEntry | 1.3.6.1.4.1.2011.5.25.316.1.1.7.1 | not-accessible | IPFPM ACHs(Atomic Closed Hop) information for a particular MCP test instance. | |
| I32 hwIpfpmMcpAchId | 1.3.6.1.4.1.2011.5.25.316.1.1.7.1.1 | Integer32 | not-accessible | The object indicates the identification of the ACH. |
| HWI hwIpfpmMcpFlowType | 1.3.6.1.4.1.2011.5.25.316.1.1.7.1.2 | HWIpfpmMcpFlowType | read-create | The object indicates the flow that the ACH monitors is 'forward(1)' or 'backward(2)', 'bidirectional(3)'. The value none(0) represents that it is not configured. |
| ROW hwIpfpmMcpAchRowStatus | 1.3.6.1.4.1.2011.5.25.316.1.1.7.1.3 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| hwIpfpmMcpTlpTable | 1.3.6.1.4.1.2011.5.25.316.1.1.8 | not-accessible | The table describe the TLPs(Target Logical Port) belonging to MCP ACHs. | |
| hwIpfpmMcpTlpEntry | 1.3.6.1.4.1.2011.5.25.316.1.1.8.1 | not-accessible | IPFPM TLPs(Target Logical Port) information for a particular MCP ACH. | |
| HWI hwIpfpmMcpTlpRole | 1.3.6.1.4.1.2011.5.25.316.1.1.8.1.1 | HWIpfpmMcpTlpRole | not-accessible | The object indicates the TLP belongs to 'in-group(1)' or 'out-group(2)' of the ACH. |
| IP hwIpfpmMcpTlpDcpId | 1.3.6.1.4.1.2011.5.25.316.1.1.8.1.2 | IpAddress | not-accessible | The object indicates the dcp which the tlp belongs to. |
| I32 hwIpfpmMcpTlpId | 1.3.6.1.4.1.2011.5.25.316.1.1.8.1.3 | Integer32 | not-accessible | The object indicates the identification of the TLP. |
| ROW hwIpfpmMcpTlpRowStatus | 1.3.6.1.4.1.2011.5.25.316.1.1.8.1.4 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| hwIpfpmMcpSrcInstReferQueryTable | 1.3.6.1.4.1.2011.5.25.316.1.1.9 | not-accessible | The table describes the information of multicast source instance referred by some multicast receiver instances. | |
| hwIpfpmMcpSrcInstReferQueryEntry | 1.3.6.1.4.1.2011.5.25.316.1.1.9.1 | not-accessible | The information is that the multicast source instance referred by some multicast receiver instances. | |
| I32 hwIpfpmMcpSrcInstReferCnt | 1.3.6.1.4.1.2011.5.25.316.1.1.9.1.1 | Integer32 | read-only | The object indicates the counter that the multicast source instance referred by some multicast receiver instances. |
| hwIpfpmMcpStatistics | 1.3.6.1.4.1.2011.5.25.316.1.2 | |||
| hwIpfpmMcpStatisticsTable | 1.3.6.1.4.1.2011.5.25.316.1.2.1 | |||
| I32 hwIpfpmMcpInstSpec | 1.3.6.1.4.1.2011.5.25.316.1.2.1.1 | Integer32 | read-only | This object indicates the global instance specification of MCP. |
| I32 hwIpfpmMcpInstCurNum | 1.3.6.1.4.1.2011.5.25.316.1.2.1.2 | Integer32 | read-only | This object indicates the current instance number of MCP. |
| hwIpfpmMcpInstAchIndexTable | 1.3.6.1.4.1.2011.5.25.316.1.2.3 | not-accessible | The tables contains the index of MCP test instances and ACH. | |
| hwIpfpmMcpInstAchIndexEntry | 1.3.6.1.4.1.2011.5.25.316.1.2.3.1 | not-accessible | Index of a particular test instance and ACH. | |
| C64 hwIpfpmMcpSeqNo | 1.3.6.1.4.1.2011.5.25.316.1.2.3.1.1 | Counter64 | read-only | Sequence of a particular test instance and ACH. |
| hwIpfpmMcpLossStatsTable | 1.3.6.1.4.1.2011.5.25.316.1.2.4 | not-accessible | The tables contains loss measure statistics of MCP test instances. | |
| hwIpfpmMcpLossStatsEntry | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1 | not-accessible | Loss measure statistics of an interval for a particular test instance. | |
| U32 hwIpfpmMcpSeqNoHigh | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.1 | Unsigned32 | not-accessible | High 32-bit of the hwIpfpmMcpSeqNo. |
| U32 hwIpfpmMcpSeqNoLow | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.2 | Unsigned32 | not-accessible | Low 32-bit of the hwIpfpmMcpSeqNo. |
| HWI hwIpfpmMcpLossErrInfo | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.3 | HWIpfpmStatErrInfo | read-only | The error code to indicate the validity and the invalidation reason of an interval's loss measure statistics. |
| C64 hwIpfpmMcpForwardLossPkts | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.4 | Counter64 | read-only | The absolute value of loss packets of forward flow measurement. |
| I32 hwIpfpmMcpForwardLossPktsSign | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.5 | Integer32 | read-only | The sign of loss packets of forward flow measurement. 1 means positive number, -1 means negative number. |
| C64 hwIpfpmMcpForwardLossBytes | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.6 | Counter64 | read-only | The absolute value of loss bytes of forward flow measurement. |
| I32 hwIpfpmMcpForwardLossBytesSign | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.7 | Integer32 | read-only | The sign of loss bytes of forward flow measurement. 1 means positive number, -1 means negative number. |
| C64 hwIpfpmMcpForwardPkts | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.8 | Counter64 | read-only | The packets of forward flow measurement. |
| C64 hwIpfpmMcpForwardBytes | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.9 | Counter64 | read-only | The bytes of forward flow measurement. |
| I32 hwIpfpmMcpForwardLossRatio | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.10 | Integer32 | read-only | This value divided by 1000000 is the loss ratio(%) of forward flow measurement. |
| C64 hwIpfpmMcpBackwardLossPkts | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.11 | Counter64 | read-only | The absolute value of loss packets of backward flow measurement. |
| I32 hwIpfpmMcpBackwardLossPktsSign | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.12 | Integer32 | read-only | The sign of loss loss packets of backward flow measurement. 1 means positive number, -1 means negative number. |
| C64 hwIpfpmMcpBackwardLossBytes | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.13 | Counter64 | read-only | The absolute value of loss bytes of backward flow measurement. |
| I32 hwIpfpmMcpBackwardLossBytesSign | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.14 | Integer32 | read-only | The sign of loss bytes of backward flow measurement. 1 means positive number, -1 means negative number. |
| C64 hwIpfpmMcpBackwardPkts | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.15 | Counter64 | read-only | The packets of backward flow measurement. |
| C64 hwIpfpmMcpBackwardBytes | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.16 | Counter64 | read-only | The bytes of backward flow measurement. |
| I32 hwIpfpmMcpBackwardLossRatio | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.17 | Integer32 | read-only | This value divided by 1000000 is the loss ratio(%) of backward flow measurement. |
| HWI hwIpfpmMcpForwardLossMMSType | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.18 | HWIpfpmMMSType | read-only | This value indicate multicastsrc type is 'master(0)' or 'slave(1)'. |
| T/F hwIpfpmMcpForwardLossMMSSwitch | 1.3.6.1.4.1.2011.5.25.316.1.2.4.1.19 | TruthValue | read-only | This value indicate whether multicastsrc switched in this period. |
| hwIpfpmMcpOneDelayStatTable | 1.3.6.1.4.1.2011.5.25.316.1.2.5 | not-accessible | The tables contains one-way delay measure statistics of MCP test instances. | |
| hwIpfpmMcpOneDelayStatEntry | 1.3.6.1.4.1.2011.5.25.316.1.2.5.1 | not-accessible | One-way delay measure statistics of an interval for a particular test instance. | |
| HWI hwIpfpmMcpOneDelayErrInfo | 1.3.6.1.4.1.2011.5.25.316.1.2.5.1.1 | HWIpfpmStatErrInfo | read-only | The error code to indicate the validity and the invalidation reason of an interval's one-way delay measure statistics. |
| I32 hwIpfpmMcpForwardOneDelay | 1.3.6.1.4.1.2011.5.25.316.1.2.5.1.2 | Integer32 | read-only | The one-way delay(us) of forward flow. |
| I32 hwIpfpmMcpForwardOneDelayVariation | 1.3.6.1.4.1.2011.5.25.316.1.2.5.1.3 | Integer32 | read-only | The one-way delay variation(us) of forward flow. |
| I32 hwIpfpmMcpBackwardOneDelay | 1.3.6.1.4.1.2011.5.25.316.1.2.5.1.4 | Integer32 | read-only | The one-way delay(us) of backward flow. |
| I32 hwIpfpmMcpBackwardOneDelayVariation | 1.3.6.1.4.1.2011.5.25.316.1.2.5.1.5 | Integer32 | read-only | The one-way delay variation(us) of backward flow. |
| HWI hwIpfpmMcpForwardOneDelayMMSType | 1.3.6.1.4.1.2011.5.25.316.1.2.5.1.6 | HWIpfpmMMSType | read-only | This value indicate multicastsrc type is 'master(0)' or 'slave(1)'. |
| hwIpfpmMcpTwoDelayStatTable | 1.3.6.1.4.1.2011.5.25.316.1.2.6 | not-accessible | The tables contains two-way delay measure statistics of MCP test instances. | |
| hwIpfpmMcpTwoDelayStatEntry | 1.3.6.1.4.1.2011.5.25.316.1.2.6.1 | not-accessible | Two-way delay measure statistics of an interval for a particular test instance. | |
| HWI hwIpfpmMcpTwoDelayErrInfo | 1.3.6.1.4.1.2011.5.25.316.1.2.6.1.1 | HWIpfpmStatErrInfo | read-only | The error code to indicate the validity and the invalidation reason of an interval's two-way delay measure statistics. |
| I32 hwIpfpmMcpTwoDelay | 1.3.6.1.4.1.2011.5.25.316.1.2.6.1.2 | Integer32 | read-only | The two-way delay(us) of monitored flow. |
| I32 hwIpfpmMcpTwoDelayVariation | 1.3.6.1.4.1.2011.5.25.316.1.2.6.1.3 | Integer32 | read-only | The two-way delay variation(us) of monitored flow. |
| I32 hwIpfpmMcpForwardDelay | 1.3.6.1.4.1.2011.5.25.316.1.2.6.1.4 | Integer32 | read-only | The forward flow delay(us) in two-way delay measurement. |
| I32 hwIpfpmMcpForwardDelayVariation | 1.3.6.1.4.1.2011.5.25.316.1.2.6.1.5 | Integer32 | read-only | The forward flow variation(us) in two-way delay measurement. |
| I32 hwIpfpmMcpBackwardDelay | 1.3.6.1.4.1.2011.5.25.316.1.2.6.1.6 | Integer32 | read-only | The backward flow delay(us) in two-way delay measurement. |
| I32 hwIpfpmMcpBackwardDelayVariation | 1.3.6.1.4.1.2011.5.25.316.1.2.6.1.7 | Integer32 | read-only | The backward flow variation(us) in two-way delay measurement. |
| hwIpfpmDcpObjects | 1.3.6.1.4.1.2011.5.25.316.2 | |||
| hwIpfpmDcpConfiguration | 1.3.6.1.4.1.2011.5.25.316.2.1 | |||
| hwIpfpmDcpGlobalTable | 1.3.6.1.4.1.2011.5.25.316.2.1.1 | |||
| HWE hwIpfpmDcpEnable | 1.3.6.1.4.1.2011.5.25.316.2.1.1.1 | HWEnabledStatus | read-write | This object indicates that the DCP (Data Collecting Point) function is 'enabled(1)' or 'disabled(2)'. |
| IP hwIpfpmDcpId | 1.3.6.1.4.1.2011.5.25.316.2.1.1.2 | IpAddress | read-write | The value of this object indicates the identification of DCP. The value 0.0.0.0 represents that it is not configured. |
| OCT hwIpfpmDcpMeasureColorFlag | 1.3.6.1.4.1.2011.5.25.316.2.1.1.3 | OCTET STRING | read-write | This string object indicates the bits of an IP packet used for color measurement. the length of string is 3,first and second character range is , third character range is . the three characters can not same. The character '0' represents none flag bit. The character '1' represents the bit0 of the FLAGS byte. The character '2' represents the bit3 of the TOS byte. The character '3' represents the bit4 of the TOS byte. The character '4' represents the bit5 of the TOS byte. The character '5' represents the bit6 of the TOS byte. The character '6' represents the bit7 of the TOS byte. the first character represents loss measurement color-bit, the second character represents delay measurement color-bit, the third character represents multicast measurement color-bit. |
| IP hwIpfpmDcpMcpId | 1.3.6.1.4.1.2011.5.25.316.2.1.1.6 | IpAddress | read-write | Identification of the MCP that DCP reports measure data of the test instances not specified the object 'hwIpfpmDcpInstMcpId' to. The value 0.0.0.0 represents that it is not configured. |
| I32 hwIpfpmDcpMcpPort | 1.3.6.1.4.1.2011.5.25.316.2.1.1.7 | Integer32 | read-write | The listening port of the MCP that DCP reports measure data of the test instances not specified the object 'hwIpfpmDcpInstMcpPort' to. It need setting 'hwIpfpmDcpMcpId' first before setting this object. |
| OCT hwIpfpmDcpMcpVpnName | 1.3.6.1.4.1.2011.5.25.316.2.1.1.8 | OCTET STRING | read-write | The name of the VPN instance through which the DCP and the MCP communicates. 'hwIpfpmDcpInstMcpId' should be setted first before setting this object. |
| HWI hwIpfpmDcpMcpVpnType | 1.3.6.1.4.1.2011.5.25.316.2.1.1.9 | HWIpfpmVpnType | read-write | The type of the VPN instance. 'hwIpfpmDcpInstMcpId' should be setted first before setting this object. |
| hwIpfpmDcpAuthTable | 1.3.6.1.4.1.2011.5.25.316.2.1.7 | not-accessible | The table contains authentication of DCP. | |
| hwIpfpmDcpAuthEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.7.1 | not-accessible | IPFPM authentication information for DCP | |
| I32 hwIpfpmDcpAuthKeyId | 1.3.6.1.4.1.2011.5.25.316.2.1.7.1.1 | Integer32 | not-accessible | Identification of the DCP authentication. |
| HWI hwIpfpmDcpAuthType | 1.3.6.1.4.1.2011.5.25.316.2.1.7.1.2 | HWIpfpmAuthType | read-write | Authentication type of the DCP. The enumeration 'hmac-sha256(1)' represents the password is sent after being encrypted through hmac-sha256. By default, authentication is not configured. |
| OCT hwIpfpmDcpAuthKey | 1.3.6.1.4.1.2011.5.25.316.2.1.7.1.3 | OCTET STRING | read-write | The password used as an IPFPM authentication key. |
| ROW hwIpfpmDcpAuthRowStatus | 1.3.6.1.4.1.2011.5.25.316.2.1.7.1.4 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| hwIpfpmDcpInstTable | 1.3.6.1.4.1.2011.5.25.316.2.1.8 | not-accessible | The table contains attribute of DCP test instances. | |
| hwIpfpmDcpInstEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1 | not-accessible | IPFPM configuration information for a particular DCP test instance. | |
| I32 hwIpfpmDcpInstId | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.1 | Integer32 | accessible-for-notify | Identification of the test instance. |
| OCT hwIpfpmDcpInstDesc | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.2 | OCTET STRING | read-create | Description of the test instance. if the string length is 0, it represents that it is not configured. |
| IP hwIpfpmDcpInstMcpId | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.3 | IpAddress | read-create | Identification of the MCP that DCP reports measure data of this test instance to. The value 0.0.0.0 represents that it is not configured |
| I32 hwIpfpmDcpInstMcpPort | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.4 | Integer32 | read-create | The listening port of the MCP that DCP reports measure data of this test instance to. It need setting 'hwIpfpmDcpInstMcpId' first before setting this object. |
| NUM hwIpfpmDcpInstInterval | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.5 | HWIpfpmInstIntervalType | read-create | This object indicates that interval of an test instance is 'interval1s(1)' or 'interval10s(10)' or 'interval60s(60)' or 'interval600s(600)'. |
| ROW hwIpfpmDcpInstRowStatus | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.6 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| HWI hwIpfpmDcpInstType | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.7 | HWIpfpmInstType | read-create | type of the test instance. |
| I32 hwIpfpmDcpSourceInstId | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.8 | Integer32 | read-create | Identification of the source instance. |
| OCT hwIpfpmDcpInstMcpVpnName | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.9 | OCTET STRING | read-create | The name of the VPN instance through which the DCP and the MCP communicates. 'hwIpfpmDcpInstMcpId' should be setted first before setting this object. |
| HWI hwIpfpmDcpInstMcpVpnType | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.10 | HWIpfpmVpnType | read-create | The type of the VPN instance. 'hwIpfpmDcpInstMcpId' should be setted first before setting this object. |
| I32 hwIpfpmDcpInstGroupId | 1.3.6.1.4.1.2011.5.25.316.2.1.8.1.11 | Integer32 | read-create | The group identification of the test instance. |
| hwIpfpmDcpInstAuthTable | 1.3.6.1.4.1.2011.5.25.316.2.1.9 | not-accessible | The table contains authentication of DCP test instances. | |
| hwIpfpmDcpInstAuthEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.9.1 | not-accessible | IPFPM authentication information for a particular DCP test instance. | |
| I32 hwIpfpmDcpInstAuthKeyId | 1.3.6.1.4.1.2011.5.25.316.2.1.9.1.1 | Integer32 | not-accessible | Identification of the DCP authentication. |
| HWI hwIpfpmDcpInstAuthType | 1.3.6.1.4.1.2011.5.25.316.2.1.9.1.2 | HWIpfpmAuthType | read-write | Authentication type of DCP instance authentication. The enumeration 'hmac-sha256(1)' represents the password is sent after being encrypted through hmac-sha256. By default, authentication is not configured. If this object is not configured and object 'hwIpfpmDcpAuthType' is configured, then this instance uses 'hwIpfpmDcpInstAuthType' and 'hwIpfpmDcpInstAuthKey' as its authentication. |
| OCT hwIpfpmDcpInstAuthKey | 1.3.6.1.4.1.2011.5.25.316.2.1.9.1.3 | OCTET STRING | read-write | The password used as an DCP test instance authentication key. |
| ROW hwIpfpmDcpInstAuthRowStatus | 1.3.6.1.4.1.2011.5.25.316.2.1.9.1.4 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| hwIpfpmDcpFlowTable | 1.3.6.1.4.1.2011.5.25.316.2.1.10 | not-accessible | The table contains flow attribute of DCP test instances. | |
| hwIpfpmDcpFlowEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1 | not-accessible | IPFPM configuration information for a particular DCP test instance flow. | |
| HWI hwIpfpmDcpFlowType | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.1 | HWIpfpmFlowType | accessible-for-notify | This object indicates that the flow is 'forward(1)' or 'backward(2)' or 'bidirectional(3)'. |
| I32 hwIpfpmDcpFlowProtocol | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.2 | Integer32 | read-create | This object indicates the protocol specified as the flow feature. 'hwIpfpmDcpFlowSrcPortBgn', 'hwIpfpmDcpFlowSrcPortEnd', 'hwIpfpmDcpFlowDstPortBgn', and 'hwIpfpmDcpFlowDstPortEnd' can be configured only when the value is 6(tcp) or 17(udp). The value 0 represents that this object is not configured. |
| I32 hwIpfpmDcpFlowDscp | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.3 | Integer32 | read-create | This object indicates the DSCP specified as the flow feature. The value -1 represents that this object is not configured. |
| IP hwIpfpmDcpFlowSrcAddr | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.4 | IpAddress | read-create | This object indicates the source ip address specified as the flow feature. The value 0.0.0.0 represents that this object is not configured. |
| I32 hwIpfpmDcpFlowSrcMaskLen | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.5 | Integer32 | read-create | This object indicates the source ip mask length specified as the flow feature. |
| IP hwIpfpmDcpFlowDstAddr | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.6 | IpAddress | read-create | This object indicates the destination ip address specified as the flow feature. The value 0.0.0.0 represents that this object is not configured. |
| I32 hwIpfpmDcpFlowDstMaskLen | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.7 | Integer32 | read-create | This object indicates the destination ip mask length specified as the flow feature. |
| I32 hwIpfpmDcpFlowSrcPortBgn | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.8 | Integer32 | read-create | This object indicates the begin value of source port specified as the flow feature. It need configure 'hwIpfpmDcpFlowProtocol' first before configure this object. The value 0 represents that this object is not configured. |
| I32 hwIpfpmDcpFlowSrcPortEnd | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.9 | Integer32 | read-create | This object indicates the end value of source port specified as the flow feature. It need configure 'hwIpfpmDcpFlowProtocol' first before configure this object. The value 0 represents that this object is not configured. |
| I32 hwIpfpmDcpFlowDstPortBgn | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.10 | Integer32 | read-create | This object indicates the begin value of destination port specified as the flow feature. It need configure 'hwIpfpmDcpFlowProtocol' first before configure this object. The value 0 represents that this object is not configured. |
| I32 hwIpfpmDcpFlowDstPortEnd | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.11 | Integer32 | read-create | This object indicates the end value of destination port specified as the flow feature. It need configure 'hwIpfpmDcpFlowProtocol' first before configure this object. The value 0 represents that this object is not configured. |
| ROW hwIpfpmDcpFlowRowStatus | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.12 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| IP hwIpfpmDcpFlowOuterSrcAddr | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.13 | IpAddress | read-create | This object indicates the outer source ip address specified as the flow feature. The value 0 represents that this object is not configured. |
| IP hwIpfpmDcpFlowOuterDstAddr | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.14 | IpAddress | read-create | This object indicates the outer destination ip address specified as the flow feature. The value 0 represents that this object is not configured. |
| U32 hwIpfpmDcpFlowForwardGtpTeid | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.15 | Unsigned32 | read-create | This object indicates the value of forward gtp teid specified as the flow feature. The value 0 represents that this object is not configured. |
| U32 hwIpfpmDcpFlowBackwardGtpTeid | 1.3.6.1.4.1.2011.5.25.316.2.1.10.1.16 | Unsigned32 | read-create | This object indicates the value of backward gtp teid specified as the flow feature. The value 0 represents that this object is not configured. |
| hwIpfpmDcpInstTlpTable | 1.3.6.1.4.1.2011.5.25.316.2.1.11 | not-accessible | The table contains attribute of TLPs. | |
| hwIpfpmDcpInstTlpEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1 | not-accessible | IPFPM configuration information for a particular TLP. | |
| HWI hwIpfpmDcpInstTlpRole | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.1 | HWIpfpmTlpRole | read-create | The object indicates the TLP position 'in-point(1)' or 'out-point(2) or 'mid-point(3)'. |
| HWI hwIpfpmDcpInstTlpFlowType | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.2 | HWIpfpmFlowType | read-create | The object indicates the flow type of the instance TLP is 'forward(1)' or 'backward(2)' or 'bidirectional(3)' or 'forwardandbackward(4)'. Only 'forward(1)' and 'backward(2)' can be configured when 'hwIpfpmDcpInstTlpRole' is 'mid-point(3)'. The value 'null(0)' represents that this flow is not configured under the instance. |
| HWI hwIpfpmDcpInstTlpDirec | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.3 | HWIpfpmFlowTlpDirec | read-create | The object indicates the TLP is 'ingress(1)' or 'egress(2)' of the flow of DCP test instance. |
| I32 hwIpfpmDcpInstTlpVpnLabel | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.4 | Integer32 | read-create | The VPN label of of the flow that the TLP measured. The value -1 represents that this object is not configured. |
| T/F hwIpfpmDcpInstTlpCtrlWordFlag | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.5 | TruthValue | read-create | The control word flag of the flow that the TLP measured. The value false(2) represents that this object is not configured. |
| I32 hwIpfpmDcpInstTlpLspLabel | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.6 | Integer32 | read-create | The LSP label of the flow that the TLP measured. The value -1 represents that this object is not configured. |
| T/F hwIpfpmDcpInstTlpL2VpnFlag | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.7 | TruthValue | read-create | The L2VPN flag of the flow that the TLP measured. The value false(2) represents that this object is not configured. |
| OCT hwIpfpmDcpInstTlpTpId | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.8 | OCTET STRING | read-create | The tpid for vlan. The value range is from '600' to 'FFFF'. |
| ROW hwIpfpmDcpInstTlpRowStatus | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.9 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| HWI hwIpfpmDcpInstTlpMultiSrcType | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.10 | HWIpfpmMMSType | read-create | The object indicates the type of multicastsrc 'master(0)'or 'slave(1)'. |
| T/F hwIpfpmDcpInstTlpFlowLabelFlag | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.11 | TruthValue | read-create | This value indicate whether the flow-label is configured. |
| I32 hwIpfpmDcpInstTlpLspLabel2 | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.12 | Integer32 | read-create | The LSP label of the flow that the TLP measured. The value -1 represents that this object is not configured. |
| I32 hwIpfpmDcpInstTlpLspLabel3 | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.13 | Integer32 | read-create | The LSP label of the flow that the TLP measured. The value -1 represents that this object is not configured. |
| I32 hwIpfpmDcpInstTlpOuterVlan | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.14 | Integer32 | read-create | The outer-vlan id of the flow that the TLP measured. The value 0 represents that this object is not configured. |
| I32 hwIpfpmDcpInstTlpInnerVlan | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.15 | Integer32 | read-create | The inner-vlan id of the flow that the TLP measured. The value 0 represents that this object is not configured. |
| I32 hwIpfpmDcpInstTlpBackwardVpnLabel | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.16 | Integer32 | read-create | The VPN label of of the flow that the TLP measured. The value -1 represents that this object is not configured. |
| T/F hwIpfpmDcpInstTlpBackwardCtrlWordFlag | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.17 | TruthValue | read-create | The control word flag of the flow that the TLP measured. The value false(2) represents that this object is not configured. |
| I32 hwIpfpmDcpInstTlpBackwardLspLabel | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.18 | Integer32 | read-create | The LSP label of the flow that the TLP measured. The value -1 represents that this object is not configured. |
| I32 hwIpfpmDcpInstTlpBackwardLspLabel2 | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.19 | Integer32 | read-create | The LSP label of the flow that the TLP measured. The value -1 represents that this object is not configured. |
| I32 hwIpfpmDcpInstTlpBackwardLspLabel3 | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.20 | Integer32 | read-create | The LSP label of the flow that the TLP measured. The value -1 represents that this object is not configured. |
| T/F hwIpfpmDcpInstTlpBackwardL2VpnFlag | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.21 | TruthValue | read-create | The L2VPN flag of the flow that the TLP measured. The value false(2) represents that this object is not configured. |
| T/F hwIpfpmDcpInstTlpBackwardFlowLabelFlag | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.22 | TruthValue | read-create | This value indicate whether the flow-label is configured. |
| I32 hwIpfpmDcpInstTlpBackwardOuterVlan | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.23 | Integer32 | read-create | The outer-vlan id of the flow that the TLP measured. The value 0 represents that this object is not configured. |
| I32 hwIpfpmDcpInstTlpBackwardInnerVlan | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.24 | Integer32 | read-create | The inner-vlan id of the flow that the TLP measured. The value 0 represents that this object is not configured. |
| OCT hwIpfpmDcpInstTlpBackwardTpId | 1.3.6.1.4.1.2011.5.25.316.2.1.11.1.25 | OCTET STRING | read-create | The tpid for vlan. The value range is from '600' to 'FFFF'. |
| hwIpfpmDcpLossMeasTable | 1.3.6.1.4.1.2011.5.25.316.2.1.12 | not-accessible | The table contains loss measure information of DCP test instances. | |
| hwIpfpmDcpLossMeasEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.12.1 | not-accessible | IPFPM loss measure configuration information for a particular DCP test instance. | |
| HWE hwIpfpmDcpLossEnable | 1.3.6.1.4.1.2011.5.25.316.2.1.12.1.1 | HWEnabledStatus | read-write | This object indicates that the on-demand loss measure function is 'enabled(1)' or 'disabled(2)'. |
| HWE hwIpfpmDcpLossContEnable | 1.3.6.1.4.1.2011.5.25.316.2.1.12.1.2 | HWEnabledStatus | read-write | This object indicates that the continual loss measure function is 'enabled(1)' or 'disabled(2)'. |
| HWI hwIpfpmDcpLossTimeRange | 1.3.6.1.4.1.2011.5.25.316.2.1.12.1.3 | HWIpfpmMeasTimeRangeType | read-write | The time range in which the on-demand loss measure function is enabled. The enumeration values include 'timerange5m(5)', 'timerange10m(10)', 'timerange15m(15)', and 'timerange30m(30)'. The value 'null(0)' represents that this object is not configured. |
| HWI hwIpfpmDcpLossTlpRole | 1.3.6.1.4.1.2011.5.25.316.2.1.12.1.4 | HWIpfpmLossTlpRole | not-accessible | The type of TLP that loss measure enabled on. The enumeration values include 'e2e(1)','section(2)' . The value 'e2e(1)' represents that this object is end-end. The value 'section(2)' represents that this object is mid-point. |
| hwIpfpmDcpDelayMeasTable | 1.3.6.1.4.1.2011.5.25.316.2.1.13 | not-accessible | The table contains delay measure information of DCP test instances. | |
| hwIpfpmDcpDelayMeasEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.13.1 | not-accessible | IPFPM delay measure configuration information for a particular DCP test instance. | |
| HWE hwIpfpmDcpDelayEnable | 1.3.6.1.4.1.2011.5.25.316.2.1.13.1.1 | HWEnabledStatus | read-write | This object indicates that the on-demand delay measure function is 'enabled(1)' or 'disabled(2)'. |
| HWE hwIpfpmDcpDelayContEnable | 1.3.6.1.4.1.2011.5.25.316.2.1.13.1.2 | HWEnabledStatus | read-write | This object indicates that the continual delay measure function is 'enabled(1)' or 'disabled(2)'. |
| HWI hwIpfpmDcpDelayMeasType | 1.3.6.1.4.1.2011.5.25.316.2.1.13.1.3 | HWIpfpmDelayMeasType | read-write | The type of delay measure. The enumeration values include 'oneway(1)' and 'twoway(2)'. The value 'null(0)' represents that this object is not configured. |
| HWI hwIpfpmDcpDelayTimeRange | 1.3.6.1.4.1.2011.5.25.316.2.1.13.1.4 | HWIpfpmMeasTimeRangeType | read-write | The time range in which the on-demand delay measure function is enabled. The enumeration values include 'timerange5m(5)', 'timerange10m(10)', 'timerange15m(15)', and 'timerange30m(30)'. The value 'null(0)' represents that this object is not configured. |
| HWI hwIpfpmDcpDelayTlpRole | 1.3.6.1.4.1.2011.5.25.316.2.1.13.1.5 | HWIpfpmDelayTlpRole | not-accessible | The type of TLP that delay measure enabled on. The enumeration values include 'e2e(1)','section(2)' . The value 'e2e(1)' represents that this object is end-end. The value 'section(2)' represents that this object is mid-point. |
| I32 hwIpfpmDcpDelayForwardTlpId | 1.3.6.1.4.1.2011.5.25.316.2.1.13.1.6 | Integer32 | read-write | The ingress TLP of the flow for one-way delay measure or the ingress TLP of the forward flow for two-way delay measure. The value 0 represents that this object is not configured. |
| I32 hwIpfpmDcpDelayBackwardTlpId | 1.3.6.1.4.1.2011.5.25.316.2.1.13.1.7 | Integer32 | read-write | The ingress TLP of the backward flow for two-way delay measure. The value 0 represents that this object is not configured. |
| hwIpfpmDcpTlpTable | 1.3.6.1.4.1.2011.5.25.316.2.1.14 | not-accessible | The table contains attribute of TLPs. | |
| hwIpfpmDcpTlpEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.14.1 | not-accessible | IPFPM configuration information for a particular TLP on interface. | |
| I32 hwIpfpmDcpTlpId | 1.3.6.1.4.1.2011.5.25.316.2.1.14.1.1 | Integer32 | not-accessible | Identification of TLP. |
| NUM hwIpfpmDcpTlpIfIndex | 1.3.6.1.4.1.2011.5.25.316.2.1.14.1.2 | InterfaceIndex | read-create | The index of the port that the TLP configured on. |
| ROW hwIpfpmDcpTlpRowStatus | 1.3.6.1.4.1.2011.5.25.316.2.1.14.1.3 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| I32 hwIpfpmDcpTlpVlanId | 1.3.6.1.4.1.2011.5.25.316.2.1.14.1.4 | Integer32 | read-create | The VLAN ID of the TLP measured. The value 0 represents ce-default-vlan. The value 65535 represents that this object is not configured. |
| hwIpfpmDcpTlpQueryTable | 1.3.6.1.4.1.2011.5.25.316.2.1.15 | not-accessible | The table contains the query interface ifindex and TLP ID with the interface. | |
| hwIpfpmDcpTlpQueryEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.15.1 | not-accessible | The TLP information which is configured with the interface. | |
| NUM hwIpfpmDcpTlpQueryIfIndex | 1.3.6.1.4.1.2011.5.25.316.2.1.15.1.1 | InterfaceIndex | not-accessible | The interface index which is configured with TLP. |
| I32 hwIpfpmDcpTlpQueryTlpId | 1.3.6.1.4.1.2011.5.25.316.2.1.15.1.2 | Integer32 | read-only | The TLP ID which is configured on the interface. |
| I32 hwIpfpmDcpTlpQueryVlanId | 1.3.6.1.4.1.2011.5.25.316.2.1.15.1.3 | Integer32 | not-accessible | The VLAN ID of the TLP measured. The value 0 represents ce-default-vlan. The value 65535 represents that this object is not configured. |
| hwIpfpmDcpSrcInstReferQueryTable | 1.3.6.1.4.1.2011.5.25.316.2.1.16 | not-accessible | The table describes the information of multicast source instance referred by some multicast receiver instances. | |
| hwIpfpmDcpSrcInstReferQueryEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.16.1 | not-accessible | The information is that the multicast source instance referred by some multicast receiver instances. | |
| I32 hwIpfpmDcpSrcInstReferCnt | 1.3.6.1.4.1.2011.5.25.316.2.1.16.1.1 | Integer32 | read-only | The object indicates the counter that the multicast source instance referred by some multicast receiver instances. |
| hwIpfpmDcpTlpQueryExtTable | 1.3.6.1.4.1.2011.5.25.316.2.1.17 | not-accessible | The table contains the query interface ifindex and TLP ID with the interface. | |
| hwIpfpmDcpTlpQueryExtEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.17.1 | not-accessible | The TLP information which is configured with the interface. | |
| NUM hwIpfpmDcpTlpQueryExtIfIndex | 1.3.6.1.4.1.2011.5.25.316.2.1.17.1.1 | InterfaceIndex | not-accessible | The interface index which is configured with TLP. |
| I32 hwIpfpmDcpTlpQueryExtTlpId | 1.3.6.1.4.1.2011.5.25.316.2.1.17.1.2 | Integer32 | read-only | The TLP ID which is configured on the interface. |
| I32 hwIpfpmDcpTlpQueryExtVlanId | 1.3.6.1.4.1.2011.5.25.316.2.1.17.1.3 | Integer32 | not-accessible | The VLAN ID of the TLP measured. The value 0 represents ce-default-vlan. The value 65535 represents that this object is not configured. |
| I32 hwIpfpmDcpTlpQueryExtOntId | 1.3.6.1.4.1.2011.5.25.316.2.1.17.1.4 | Integer32 | not-accessible | This object indicates the ONT ID. |
| INT hwIpfpmDcpTlpQueryExtOntPortType | 1.3.6.1.4.1.2011.5.25.316.2.1.17.1.5 | INTEGER | not-accessible | This object indicates the ONT port's type. Options: 1. eth (47)) -indicates ONT port's type is the eth type. 2. invalid(-1) -indicates ONT port's type is not matched. |
| I32 hwIpfpmDcpTlpQueryExtOntPortId | 1.3.6.1.4.1.2011.5.25.316.2.1.17.1.6 | Integer32 | not-accessible | This object indicates the ONT port ID. |
| hwIpfpmDcpTlpExtTable | 1.3.6.1.4.1.2011.5.25.316.2.1.18 | not-accessible | The table contains attribute of TLPs. | |
| hwIpfpmDcpTlpExtEntry | 1.3.6.1.4.1.2011.5.25.316.2.1.18.1 | not-accessible | IPFPM configuration information for a particular TLP on interface. | |
| I32 hwIpfpmDcpExtTlpId | 1.3.6.1.4.1.2011.5.25.316.2.1.18.1.1 | Integer32 | not-accessible | Identification of TLP. |
| I32 hwIpfpmDcpTlpExtIfIndex | 1.3.6.1.4.1.2011.5.25.316.2.1.18.1.2 | Integer32 | read-create | The index of the port that the TLP configured on. |
| ROW hwIpfpmDcpTlpExtRowStatus | 1.3.6.1.4.1.2011.5.25.316.2.1.18.1.3 | RowStatus | read-create | Used for controlling the creation and deletion of this row. |
| I32 hwIpfpmDcpTlpExtVlanId | 1.3.6.1.4.1.2011.5.25.316.2.1.18.1.4 | Integer32 | read-create | The VLAN ID of the TLP measured. The value 0 represents ce-default-vlan. The value 65535 represents that this object is not configured. |
| I32 hwIpfpmDcpTlpExtOntId | 1.3.6.1.4.1.2011.5.25.316.2.1.18.1.5 | Integer32 | read-create | This object indicates the ONT ID. The value -1 represents that this object is not configured. |
| INT hwIpfpmDcpTlpExtOntPortType | 1.3.6.1.4.1.2011.5.25.316.2.1.18.1.6 | INTEGER | read-create | This object indicates the ONT port's type. Options: 1. eth (47)) -indicates ONT port's type is the eth type. 2. invalid(-1) -indicates ONT port's type is not matched. DEFVAL { -1 } . |
| I32 hwIpfpmDcpTlpExtOntPortId | 1.3.6.1.4.1.2011.5.25.316.2.1.18.1.7 | Integer32 | read-create | This object indicates the ONT port ID. The value -1 represents that this object is not configured. |
| hwIpfpmDcpTrapObjects | 1.3.6.1.4.1.2011.5.25.316.2.2 | |||
| I32 hwIpfpmTlpExceedBoardId | 1.3.6.1.4.1.2011.5.25.316.2.2.1 | Integer32 | accessible-for-notify | The board ID that the tlp exceed the threshold. |
| I32 hwIpfpmTlpNumber | 1.3.6.1.4.1.2011.5.25.316.2.2.2 | Integer32 | accessible-for-notify | The number of tlp. |
| I32 hwIpfpmTlpThreshold | 1.3.6.1.4.1.2011.5.25.316.2.2.3 | Integer32 | accessible-for-notify | The threshold of tlp. |
| hwIpfpmTraps | 1.3.6.1.4.1.2011.5.25.316.3 | |||
| NTF hwIpfpmLossRatioExceed | 1.3.6.1.4.1.2011.5.25.316.3.1 | A hwIpfpmLossRatioExceed trap is sent when the loss ratio of IPFPM test instance exceeds the uppper threshold in continuous five test intervals. | ||
| NTF hwIpfpmLossRatioRecovery | 1.3.6.1.4.1.2011.5.25.316.3.2 | A hwIpfpmLossRatioRecovery trap is sent when the loss ratio of IPFPM test instance is under the lower threshold in continuous five test intervals. | ||
| NTF hwIpfpmOneDelayExceed | 1.3.6.1.4.1.2011.5.25.316.3.3 | A hwIpfpmOneDelayExceed trap is sent when the one-way delay of IPFPM test instance exceeds the uppper threshold in continuous five test intervals. | ||
| NTF hwIpfpmOneDelayRecovery | 1.3.6.1.4.1.2011.5.25.316.3.4 | A hwIpfpmOneDelayRecovery trap is sent when the one-way delay of IPFPM test instance is under the lower threshold in continuous five test intervals. | ||
| NTF hwIpfpmTwoDelayExceed | 1.3.6.1.4.1.2011.5.25.316.3.5 | A hwIpfpmTwoDelayExceed trap is sent when the two-way delay of IPFPM test instance exceeds the uppper threshold in continuous five test intervals. | ||
| NTF hwIpfpmTwoDelayRecovery | 1.3.6.1.4.1.2011.5.25.316.3.6 | A hwIpfpmTwoDelayRecovery trap is sent when the two-way delay of IPFPM test instance is under the lower threshold in continuous five test intervals. | ||
| NTF hwIpfpmDcpFlowConflict | 1.3.6.1.4.1.2011.5.25.316.3.7 | A hwIpfpmDcpFlowConflict trap is sent when the flow configuration conflicts with another existing flow configuration. The first hwIpfpmDcpInstId and hwIpfpmDcpFlowType indicates the specified flow. The second hwIpfpmDcpInstId and hwIpfpmDcpFlowType indicates the existing flow. | ||
| NTF hwIpfpmTlpExceed | 1.3.6.1.4.1.2011.5.25.316.3.8 | A hwIpfpmTlpExceed trap is sent when the number of board tlp exceeds the threshold. | ||
| NTF hwIpfpmTlpRecovery | 1.3.6.1.4.1.2011.5.25.316.3.9 | A hwIpfpmTlpRecovery trap is sent when the number of board tlp is under the threshold. | ||
| hwIpfpmConformance | 1.3.6.1.4.1.2011.5.25.316.4 | |||
| hwIpfpmCompliances | 1.3.6.1.4.1.2011.5.25.316.4.1 | |||
| hwIpfpmCompliance | 1.3.6.1.4.1.2011.5.25.316.4.1.1 | The compliance statement for entities which implement the IPFPM MIB. | ||
| hwIpfpmGroups | 1.3.6.1.4.1.2011.5.25.316.4.2 | |||
| hwIpfpmMcpConfigGroup | 1.3.6.1.4.1.2011.5.25.316.4.2.1 | The collection of objects which are used to configure the IPFPM MCP behavior. | ||
| hwIpfpmMcpInstConfigGroup | 1.3.6.1.4.1.2011.5.25.316.4.2.2 | The collection of objects which are used to configure the IPFPM MCP test instance behavior. | ||
| hwIpfpmMcpStatsGroup | 1.3.6.1.4.1.2011.5.25.316.4.2.3 | The collection of objects which are used to represent the IPFPM test instance statistics. | ||
| hwIpfpmDcpConfigGroup | 1.3.6.1.4.1.2011.5.25.316.4.2.4 | The collection of objects which are used to configure the IPFPM DCP behavior. | ||
| hwIpfpmDcpInstConfigGroup | 1.3.6.1.4.1.2011.5.25.316.4.2.5 | The collection of objects which are used to configure the IPFPM DCP test instance behavior. | ||
| hwIpfpmDcpTlpConfigGroup | 1.3.6.1.4.1.2011.5.25.316.4.2.6 | The collection of objects which are used to configure the IPFPM TLP behavior. | ||
| hwIpfpmTrapsGroup | 1.3.6.1.4.1.2011.5.25.316.4.2.7 | The collection of traps used to indicate that the measured network performance is in fault or not. |
RFC description
Manages IPFPM (IP Flow Performance Measurement) with measurement control points, data collection points, and target logic points for IP flow performance monitoring.
Start monitoring Huawei carrier router/switch supporting IPFPM (IP Flow Performance Measurement) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.