HUAWEI-IF-EXT-MIB

All MIBs › HUAWEI-IF-EXT-MIB

Organization: Huawei Technologies co.,Ltd.

Last Updated: 2006-10-31

Category: Network Interfaces, Vendor: Huawei

Description: Huawei interface extension MIB providing supplementary per-interface configuration and statistics objects beyond the standard IF-MIB.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-IF-EXT-MIB?

HUAWEI-IF-EXT-MIB extends the standard IETF IF-MIB with additional per-interface configuration and statistics objects on Huawei routers and switches, covering IP assignment method, SDH-specific interface statistics, and interface health monitoring thresholds. It exposes objects for interface IP configuration mode, SDH error statistics, CRC error counts, pause-frame statistics, input/output rate percentages versus configured thresholds, propagation delay values, and VRRP member-interface administration. This module is heavily oriented toward performance and fault monitoring of interface hardware: administrators can watch CRC and SDH error counters, input/output utilization against configured thresholds, and pause-frame (flow control) statistics to detect congestion, physical-layer errors, or flow-control storms on a link. It directly depends on and complements the standard IETF IF-MIB, reusing its interface indexing while adding Huawei-specific monitoring columns. It is deployed on Huawei enterprise and carrier routers/switches, especially those carrying SDH/SONET transport or requiring granular link-health monitoring and VRRP redundancy. Engineers can download the HUAWEI-IF-EXT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-IF-EXT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei routers
Huawei switches

Monitoring Examples

An administrator would poll hwIfMonitorCrcErrorStatistics and hwIfMonitorSdhErrorStatistics per hwIfMonitorIndex to detect physical-layer degradation on an SDH-carrying interface, and compare hwIfMonitorInputRatePercentage against hwIfMonitorInputRateThreshold to see if a link is approaching saturation. Rising hwIfMonitorPauseFrameStatistics values crossing hwIfMonitorPauseFrameThreshold within hwIfMonitorPauseFrameInterval would indicate flow-control congestion likely caused by a downstream bottleneck. The hwIfSdhStatTable would be checked directly on SDH interfaces for transport-layer error events, while hwAdminVrrpMemberIf status confirms whether a VRRP member interface is correctly administered.

What Can Be Monitored

interface CRC error statistics
SDH interface error statistics
input/output rate percentage vs threshold
pause-frame (flow control) statistics
interface propagation delay
VRRP member interface administration

Imported Objects

From ATM-TC-MIB

AtmVcIdentifier
AtmVpIdentifier

From HUAWEI-MIB

hwDatacomm

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifAdminStatus	OBJECT-TYPE
ifDescr	OBJECT-TYPE
ifIndex	OBJECT-TYPE
ifName	OBJECT-TYPE
ifOperStatus	OBJECT-TYPE

From IP-MIB

ipAdEntNetMask

OBJECT-TYPE

From Q-BRIDGE-MIB

PortList
VlanIdOrNone

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-MIB

sysUpTime

OBJECT-TYPE

From SNMPv2-SMI

Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
PhysAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using hwIfEtherStatInPkts64Octets OID:

Select a Huawei router or switch (extended interface/SDH/VRRP statistics) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hwIfEtherStatInPkts64Octets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of recieved Packets whose size over 1518 bytes. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwIFExtMib	1.3.6.1.4.1.2011.5.25.41			Some attribute of interface extended content, information of interface IP, interface of trunk interface.
hwIFExtObjects	1.3.6.1.4.1.2011.5.25.41.1
hwIFExtBase	1.3.6.1.4.1.2011.5.25.41.1.1
hwIFExtTable	1.3.6.1.4.1.2011.5.25.41.1.1.1		not-accessible	Interface extended table of private mib.
hwIFExtEntry	1.3.6.1.4.1.2011.5.25.41.1.1.1.1		not-accessible	Entries of private extended interface table.
NUM hwIFExtIndex	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.1	InterfaceIndex	not-accessible	Index of extended table of interface.
INT hwIFExtLayer	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.2	INTEGER	read-write	Switch the port between Layer3 and Layer2. Corresponding to the port switch command.Layer2(1) is 1 when the port switch from layer3 to layer2.Layer3(1) is 1 when the port switch from lyaer2 to layer3.
INT hwIFExtFrameType	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.3	INTEGER	read-only	Frame type is accepted by VLAN virtual interfaces.Frame format contains ethernetII(1),ethernetII(2),ethernet8022(3),ethernet8023. The type location setting 1 when the ethernetII(1) type is accepted.Now only surpport the first(ethernetII(1))
I32 hwIFExtFlowStatInterval	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.4	Integer32	read-write	Interval of interface flow stat.The value of interval must be divided exactly by 10.The interface interval is effective,when both interface interval and global interval are config.Globle interval is only effective in interfaces,which interface interval is not configured. The real time property of interface flow stat rate will be affected by the value of interval.
ENA hwIFExtFlushReceiveEnable	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.5	EnabledStatus	read-write	Whether or not permit the port to take over FLUSHDUs. Once it is enabled, the port will take over SmartLink FlushDUs from related vlans so as to delete the MAC forwarding table in the local equipment.
VLA hwIFExtFlushVlanId	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.6	VlanIdOrNone	read-write	The ID of Vlan the port belongs to.When it is 0, it indicates the function of receiving FlushPDU is disabled.
STR hwIFExtFlushPasswd	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.7	SnmpPasswdString	read-write	A 16-octet read-write value used to define the password for negotiation.
INT hwIFExtFlowStatus	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.8	INTEGER	read-only	Current flow status of interface. 1:flow up 2:flow down
I32 hwIFExtMtu	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.9	Integer32	read-write	The Max Transmit Unit of the interface.
PHY hwIFExtMacAddr	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.10	PhysAddress	read-write	The MAC address of the interface .
I32 hwIFExtBlockPriority	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.11	Integer32	read-write	The blocked priority of the interface.
INT hwIFExtMacShift	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.12	INTEGER	read-write	The mac-shift state of the interface. 1:normal 2:monitor mac-shift
INT hwIFExtSuppressStatus	1.3.6.1.4.1.2011.5.25.41.1.1.1.1.13	INTEGER	read-only	The suppress state of the interface. 0:unsuppress 1:suppress
INT hwIFExtPhyStatus	1.3.6.1.4.1.2011.5.25.41.1.1.2	INTEGER	accessible-for-notify	The physical status of member interface.
STR hwIFExtMemberOf	1.3.6.1.4.1.2011.5.25.41.1.1.3	DisplayString	accessible-for-notify	The description of the main interface which has the membership with the member interface.
hwLinkModeChangeAutoCreateIfTable	1.3.6.1.4.1.2011.5.25.41.1.1.4		not-accessible	Interface extended table of private mib.
hwLinkModeChangeAutoCreateIfEntry	1.3.6.1.4.1.2011.5.25.41.1.1.4.1		not-accessible	Entries of private extended interface table.
NUM hwAutoIfIndex	1.3.6.1.4.1.2011.5.25.41.1.1.4.1.1	InterfaceIndex	not-accessible	Index of extended table of interface.
BIT hwNewIfTimeslot	1.3.6.1.4.1.2011.5.25.41.1.1.4.1.2	Bits	read-only	The time slot of the TDM interface: timeslot0(0):The time slot 0 on the TDM interface, timeslot1(1):The time slot 1 on the TDM interface, timeslot2(2):The time slot 2 on the TDM interface, timeslot3(3):The time slot 3 on the TDM interface, timeslot4(4):The time slot 4 on the TDM interface, timeslot5(5):The time slot 5 on the TDM interface, timeslot6(6):The time slot 6 on the TDM interface, timeslot7(7):The time slot 7 on the TDM interface, timeslot8(8):The time slot 8 on the TDM interface, timeslot9(9):The time slot 9 on the TDM interface, timeslot10(10):The time slot 10 on the TDM interface, timeslot11(11):The time slot 11 on the TDM interface, timeslot12(12):The time slot 12 on the TDM interface, timeslot13(13):The time slot 13 on the TDM interface, timeslot14(14):The time slot 14 on the TDM interface, timeslot15(15):The time slot 15 on the TDM interface, timeslot16(16):The time slot 16 on the TDM interface, timeslot17(17):The time slot 17 on the TDM interface, timeslot18(18):The time slot 18 on the TDM interface, timeslot19(19):The time slot 19 on the TDM interface, timeslot20(20):The time slot 20 on the TDM interface, timeslot21(21):The time slot 21 on the TDM interface, timeslot22(22):The time slot 22 on the TDM interface, timeslot23(23):The time slot 23 on the TDM interface, timeslot24(24):The time slot 24 on the TDM interface, timeslot25(25):The time slot 25 on the TDM interface, timeslot26(26):The time slot 26 on the TDM interface, timeslot27(27):The time slot 27 on the TDM interface, timeslot28(28):The time slot 28 on the TDM interface, timeslot29(29):The time slot 29 on the TDM interface, timeslot30(30):The time slot 30 on the TDM interface, timeslot31(31):The time slot 31 on the TDM interface.
I32 hwIFExtPhyNumber	1.3.6.1.4.1.2011.5.25.41.1.1.5	Integer32	read-only	The number of the physical interfaces.
hwInterfaceIp	1.3.6.1.4.1.2011.5.25.41.1.2
hwIfIpTable	1.3.6.1.4.1.2011.5.25.41.1.2.1		not-accessible	Interface IP address configuration table .It contains IP address, IP address mask, IP address acquiring method.
hwIfIpEntry	1.3.6.1.4.1.2011.5.25.41.1.2.1.1		not-accessible	Interface IP address configuration
IP hwIpAdEntAddr	1.3.6.1.4.1.2011.5.25.41.1.2.1.1.1	IpAddress	read-only	The IP address to which this entry's addressing information pertains.
I32 hwIpAdEntIfIndex	1.3.6.1.4.1.2011.5.25.41.1.2.1.1.2	Integer32	read-create	The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
IP hwIpAdEntNetMask	1.3.6.1.4.1.2011.5.25.41.1.2.1.1.3	IpAddress	read-create	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the host bits set to 0.
I32 hwIpAdEntBcastAddr	1.3.6.1.4.1.2011.5.25.41.1.2.1.1.4	Integer32	read-only	The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
I32 hwIpAdEntReasmMaxSize	1.3.6.1.4.1.2011.5.25.41.1.2.1.1.5	Integer32	read-only	The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagram received on this interface.
ADR hwIpAdEntAddressType	1.3.6.1.4.1.2011.5.25.41.1.2.1.1.6	HwIpAddressType	read-create	The flag indicates whether the IP address is primary IP address. One interface has only one primary IP address, but can have many sub IP address. So when add a primary IP address to an interface that has already a primary IP address, the new primary address will replace old primary address and the old primary address will be deleted.
INT hwIfIpMethod	1.3.6.1.4.1.2011.5.25.41.1.2.1.1.7	INTEGER	read-write	Interface IP address acquiring method. assignedIp(1) indicates that the address was manually configured to a specified address, for example, by user configuration. dhcpIp(2) indicates an address that was assigned to this system by a DHCP server. bootpIp(3) indicates an address that was assigned to this system by the bootp protocol. other(4) indicates an address created by another method. linklayer(5) indicates an address created by IPv6 stateless auto-configuration. random(6) indicates an address chosen by the system at random, for example, an IPv4 address within 169.254/16, or an RFC 3041 privacy address.
ROW hwIpAdEntAddrStatus	1.3.6.1.4.1.2011.5.25.41.1.2.1.1.8	RowStatus	read-create	The row status variable.
hwIfIpUnnumberedTable	1.3.6.1.4.1.2011.5.25.41.1.2.2		not-accessible	Interface IP address unnumbered table. It contains lend IP address and lend IP address mask.
hwIfIpUnnumberedEntry	1.3.6.1.4.1.2011.5.25.41.1.2.2.1		not-accessible	Interface IP address unnumbered configuration
NUM hwUnnumberedIfIndex	1.3.6.1.4.1.2011.5.25.41.1.2.2.1.1	InterfaceIndex	not-accessible	The index value of the unnumbered interface.
NUM hwLendIfIndex	1.3.6.1.4.1.2011.5.25.41.1.2.2.1.11	InterfaceIndex	read-create	The index value of the lend interface.
IP hwLendIpAddr	1.3.6.1.4.1.2011.5.25.41.1.2.2.1.12	IpAddress	read-only	The IP address of the lend interface.
IP hwLendIpAddrNetMask	1.3.6.1.4.1.2011.5.25.41.1.2.2.1.13	IpAddress	read-only	The IP address mask of the lend interface.
ROW hwUnnumberedRowStatus	1.3.6.1.4.1.2011.5.25.41.1.2.2.1.51	RowStatus	read-create	The row status variable.
hwTrunkAttr	1.3.6.1.4.1.2011.5.25.41.1.3
I32 hwTrunkIfMax	1.3.6.1.4.1.2011.5.25.41.1.3.1	Integer32	read-only	The maximum of Trunk interface
I32 hwTrunkNextIndex	1.3.6.1.4.1.2011.5.25.41.1.3.2	Integer32	read-only	The nextindex of Trunk interface,that means its position
hwTrunkIfTable	1.3.6.1.4.1.2011.5.25.41.1.3.3		not-accessible	The trunk table.
hwTrunkIfEntry	1.3.6.1.4.1.2011.5.25.41.1.3.3.1		not-accessible	Entries of the trunk table.
I32 hwTrunkIndex	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.1	Integer32	not-accessible	The number of the Trunk interface
I32 hwTrunkIfID	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.2	Integer32	read-create	The identification of the Trunk interface.It may identify Trunk and is an index of the interface.
INT hwTrunkIfType	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.3	INTEGER	read-create	The type of the Trunk interface includes eth-trunk and ip-trunk. The ip-trunk is only comprised by pos link, otherwise the eth-trunk is only comprised by ethernet link.
NUM hwTrunkIfIndex	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.4	InterfaceIndex	read-only	Index number of the Trunk interface,it is consistent with ifIndex of ifTable in IF-MIB.
INT hwTrunkIfModel	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.5	INTEGER	read-create	Participated model of interface load. sourceDesMac(1) and sourceMac(10) and desMac(11) are Layer2 hash arithmetic.
I32 hwTrunkIfBandWidthAffectLinkNum	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.6	Integer32	read-create	The max bandwidth-affected-linknumber, by default, an Eth-Trunk interface has a maximum of 16 physical interfaces. The number of physical interfaces in an Eth-Trunk interface varies according to the product type.Only in layer 2,can set this value.
I32 hwTrunkIfMinLinkNum	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.7	Integer32	read-create	The Trunk port changes to up when the number of the up port reach hwTrunkIfMinLinkNum.
ROW hwTrunkIfRowStatus	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.8	RowStatus	read-create	Current operation status of the row
INT hwTrunkIfWorkingMode	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.9	INTEGER	read-create	Current working mode of trunk. 1:master/backup access mode 2:normal mode 3:lacp static mode
INT hwTrunkIfWorkingState	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.10	INTEGER	read-only	Current working state of backup-access trunk. 1:general mode working state 2:initialization 3:master working 4:backup working
INT hwTrunkIfAutoRecover	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.11	INTEGER	read-create	If auto-recover has been set, the master port will be working instead of the other port when it changes from down state to up state. 1: don't support auto-recover 2: support auto-recover
INT hwTrunkIfPreemptEnable	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.12	INTEGER	read-create	The preemption according to the priority will be and only be enabled when the lag port is working in static mode(M:N backup mode) In default condition, the preemption is disabled.
I32 hwTrunkIfPreemptDelay	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.13	Integer32	read-create	The waiting time for priority preemption; Unit: second. It is enabled only when the priority preemption is enabled. It indicates, When it comes to priority preemption, the operation of preemption will be delayed for hwTrunkIfPreemptDelay time.
INT hwTrunkIfTimeoutReceive	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.14	INTEGER	read-create	The expired time for the port to receive LACPDUS. There are two types: 1.fast: 3 seconds 2.slow: 90 seconds
INT hwTrunkIfFlushSendEnable	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.15	INTEGER	read-create	Whether or not permit the trunk to transmit FlushDUs.It is only used when it is in the handwork 1:1 mode.Once it is enabled, the newly active interface in the trunk will send SmartLink FlushDUs so as to delete the related MAC forwarding table of the layer2 equipment in network.Otherwise, SmartLink FlushDUs will not be sent.
I32 hwTrunkIfFlushVlanId	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.16	Integer32	read-create	The ID of Vlan the partner port belongs to.When it is 0, it indicates the function of sending FlushPDU is disabled.
STR hwTrunkIfFlushPasswd	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.17	SnmpPasswdString	read-create	A 16-octet read-create value used to define the password for negotiation.
INT hwTrunkIfForceSwitchEnable	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.18	INTEGER	read-create	It is only used when it is in the handwork 1:1 mode and the current working link is the backup link. At that time, working link will move from backup link to master link. However, if the master link is down, the operation will be forbidden.
INT hwTrunkIfStatReset	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.19	INTEGER	read-create	Reset the statistic information of LACPDUsRx,MarkerPDUsRx,LACPDUsTx, MarkerResponsePDUsTx for all the ports in the current trunk.
I32 hwTrunkBandwidth	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.20	Integer32	read-create	Current bandwidth of trunk in units of 1,000,000 bits per second. This bandwidth is the peculiar property of Eth-Trunk. And to the other kinds of trunk, this bandwidth is -1.
I32 hwTrunkIfArpSendSpeed	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.21	Integer32	read-create	Indicates the rate of sending gratuitous ARP packets (in pkts/sec) on the trunk member interface.
INT hwTrunkIfLagSelectedPortStd	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.22	INTEGER	read-create	The static mode Eth-trunk selected port standard. There are two types: 1.speed : selected by port's speed 2.priority: selected by port's priority The default type is priority.
I32 hwTrunkIfLagMaxActiveLinkNum	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.23	Integer32	read-create	The static mode Eth-trunk selected ports can not more than the value.
I32 hwTrunkETrunkPriority	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.24	Integer32	read-write	The priority of the E-Trunk.
PHY hwTrunkETrunkSysID	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.25	PhysAddress	read-write	The system ID of the E-Trunk. If set ffff-ffff-ffff the system ID will be to default.
INT hwTrunkETrunkPriorityReset	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.26	INTEGER	read-write	Status of operation, there are yes(1) and no(2). It expresses whether the configure of E-Trunk priority is resetted.
INT hwTrunkETrunkSysIDReset	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.27	INTEGER	read-write	Status of operation, there are yes(1) and no(2). It expresses whether the configure of E-Trunk system ID is resetted.
INT hwTrunkLocalPrefMode	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.28	INTEGER	read-write	Local-preference transmit mode of eth-trunk, there are enable(1) and disable(2).The default value is disable(2).
I32 hwTrunkIfTrackVrrpVrid	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.29	Integer32	read-write	The VRID which the static mode Eth-trunk tracked to.
NUM hwTrunkIfTrackVrrpIfIndex	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.30	InterfaceIndex	read-write	The VRRP interface which the static mode Eth-trunk tracked to.
INT hwTrunkIfTrackVrrpReset	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.31	INTEGER	read-write	Status of operation, there are yes(1) and no(2). The value of this object identifies whether the operation of clearing the configuration is performed. And the configuration is that the Eth-Trunk interface in static LACP mode is associated with an mVRRP backup group. The value yes(1) indicates performing the operation. This object indicates one operation but not one status, so when the operation is performed, the value is no(2). By default, the value is no(2).
ENA hwTrunkIfBackupPreemptEnable	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.32	EnabledStatus	read-write	The preemption according to the master and slave port will be and only be enabled when eth-trunk is working in backup mode. In default condition, the preemption is disabled.
I32 hwTrunkIfBackupPreemptDelay	1.3.6.1.4.1.2011.5.25.41.1.3.3.1.33	Integer32	read-write	The waiting time for priority preemption; Unit: minute. It is enabled only when the priority preemption is enabled. It indicates, When it comes to priority preemption, the operation of preemption will be delayed for hwTrunkIfBackupPreemptDelay time.
I32 hwTrunkSystemPriority	1.3.6.1.4.1.2011.5.25.41.1.3.4	Integer32	read-write	The priority of the system.
INT hwTrunkUnknownUnicastIfModel	1.3.6.1.4.1.2011.5.25.41.1.3.5	INTEGER	read-write	Participated model of load for unknown unicast. sourceDesMac(2) and sourceMac(10) and desMac(11) are Layer2 hash arithmetic.
I32 hwTrunkETrunkSystemPriority	1.3.6.1.4.1.2011.5.25.41.1.3.6	Integer32	read-write	The system priority of the E-Trunk.
PHY hwTrunkETrunkSystemID	1.3.6.1.4.1.2011.5.25.41.1.3.7	PhysAddress	read-write	The system ID of the E-Trunk. If set ffff-ffff-ffff the system ID will be to default.
hwTrunkMemAttr	1.3.6.1.4.1.2011.5.25.41.1.4
hwTrunkMemTable	1.3.6.1.4.1.2011.5.25.41.1.4.1		not-accessible	Trunk member attribute information table.
hwTrunkMemEntry	1.3.6.1.4.1.2011.5.25.41.1.4.1.1		not-accessible	Trunk member attribute information
I32 hwTrunkMemifIndex	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.1	Integer32	not-accessible	Trunk port index
INT hwTrunkValidEntry	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.2	INTEGER	read-only	Valid Entries of Trunk interface
INT hwTrunkSelectStatus	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.3	INTEGER	read-create	Selected Status of Trunk Port.It is used LACP.
ENA hwTrunkLacpStatus	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.4	EnabledStatus	read-only	It is status of the LACP.
ENA hwTrunkDeleteFlag	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.5	EnabledStatus	read-create	Flag is set trunk_del_enable(1) or trunk_del_disable(2), according to operation.
INT hwTrunkOperstatus	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.6	INTEGER	read-only	Status of operation, indicates port status. There are trunk_up(1) and trunk_down(2).It expresses whether port is shutdown.
T/F hwTrunkIsDefaultLagRecv	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.7	TruthValue	read-only	We don't sustain now, default value is false.
U32 hwTrunkPortWeight	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.8	Unsigned32	read-create	Port weight, it expresses proportion of port in Trunk interface table
U32 hwTrunkPortStandby	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.9	Unsigned32	read-create	The value is backup of Trunk Port.
ROW hwTrunkRowStatus	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.10	RowStatus	read-create	Current operation status of the row.
INT hwTrunkPortMaster	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.11	INTEGER	read-create	Master port of backup-access eth-trunk or not 1: port-slave 2: port-master
I32 hwTrunkPortPriority	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.12	Integer32	read-create	The priority value assigned to this Trunk Port. This 16-bit value is read-write.
INT hwTrunkPortStatReset	1.3.6.1.4.1.2011.5.25.41.1.4.1.1.13	INTEGER	read-create	Reset the statistic information of LACPDUsRx,MarkerPDUsRx,LACPDUsTx, MarkerResponsePDUsTx for the current port.
hwIFFlowStat	1.3.6.1.4.1.2011.5.25.41.1.5
I32 hwIFFlowStatGlobalInterval	1.3.6.1.4.1.2011.5.25.41.1.5.1	Integer32	read-write	Global interval of interface flow stat.The interface interval is effective, when both interface interval and global interval are config.Globle interval is only effective in interfaces,which interface interval is not configged. Flow stat rate of interface will be affected by the value of interval. The default value is 300s.
hwIfStatistics	1.3.6.1.4.1.2011.5.25.41.1.6
hwIfEtherStatTable	1.3.6.1.4.1.2011.5.25.41.1.6.1		not-accessible	Ethernet Interface Statistic Table
hwIfEtherStatEntry	1.3.6.1.4.1.2011.5.25.41.1.6.1.1		not-accessible	Entry of Ethernet Interface Statistic Table
NUM hwIfEtherStatIfIndex	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.1	InterfaceIndex	not-accessible	The index of L2 interface
C64 hwIfEtherStatInPkts64OctetsEx	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.5	Counter64	read-only	The number of recieved Packets whose size over 1518 bytes
C64 hwIfEtherStatInPkts65to127Octets	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.6	Counter64	read-only	The number of recieved Packets whose size over 1518 bytes
C64 hwIfEtherStatInPkts128to255Octets	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.7	Counter64	read-only	The number of recieved Packets whose size over 1518 bytes
C64 hwIfEtherStatInPkts256to511Octets	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.8	Counter64	read-only	The number of recieved Packets whose size over 1518 bytes
C64 hwIfEtherStatInPkts512to1023Octets	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.9	Counter64	read-only	The number of recieved Packets whose size over 1518 bytes
C64 hwIfEtherStatInPkts1024to1518Octets	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.10	Counter64	read-only	The number of recieved Packets whose size over 1518 bytes
C64 hwIfEtherStatInJumboPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.11	Counter64	read-only	The number of recieved Packets whose size over 1518 bytes
C64 hwIfEtherStatInCRCPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.12	Counter64	read-only	The number of recieved Packets which have CRC checking errors
C64 hwIfEtherStatInLongPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.13	Counter64	read-only	The number of recieved Packets whose length is over maximum length
C64 hwIfEtherStatInJabberPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.14	Counter64	read-only	The number of recieved Packets whose length is over maximum length and wrong CRC checking
C64 hwIfEtherStatInFragmentPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.15	Counter64	read-only	The number of recieved Packets which have short size and wrong CRC checking
C64 hwIfEtherStatInUnderSizePkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.16	Counter64	read-only	The number of recieved Packets which have short size but right CRC checking
C64 hwIfEtherStatInOverRunPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.17	Counter64	read-only	The number of recieved Packets whose queue overflow
C64 hwIfEtherStatInPausePkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.18	Counter64	read-only	The number of recieved control Frames
C64 hwIfEtherStatOutJumboPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.19	Counter64	read-only	The number of sended Packets whose size over 1518 bytes
C64 hwIfEtherStatOutOverflowPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.20	Counter64	read-only	The number of Packets whitch happen FIFO overflow error
C64 hwIfEtherStatOutUnderRunPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.21	Counter64	read-only	The number of Packets whitch happen FIFO empty
C64 hwIfEtherStatOutPausePkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.22	Counter64	read-only	The number of sended control Frames
INT hwIfEthIfStatReset	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.23	INTEGER	read-write	Reset the Statistic information Counter
C64 hwIfEtherStatInDropEventPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.24	Counter64	read-only	The number of recieved Packets discarded for GBP full or back pressure discard
C64 hwIfEtherStatInAlignmentPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.25	Counter64	read-only	The number of recieved Packets which have frame alignment error
C64 hwIfEtherStatInSymbolPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.26	Counter64	read-only	The number of recieved Packets which have unknown symbols
C64 hwIfEtherStatInIgnoredPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.27	Counter64	read-only	The number of recieved MAC control frames which have unknown opecode
C64 hwIfEtherStatInFramePkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.28	Counter64	read-only	The number of recieved frames whose actual length differs with 802.3
C64 hwIfEtherStatOutCollisionPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.29	Counter64	read-only	The number of sended collision Frames(only happen in the 10/100M port with half duplex mode)
C64 hwIfEtherStatOutDeferredPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.30	Counter64	read-only	The number of sended deferred but not collision Frames(only happen in the 10/100M port)
C64 hwIfEtherStatOutLateCollisionPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.31	Counter64	read-only	The number of sended deferred and collision Frames(only happen in the 10/100M port)
C64 hwIfEtherStatOutExcessiveCollisionPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.32	Counter64	read-only	The number of sended failure Frames whose collision more than 16(only happen in the 10/100M port)
C64 hwIfEtherStatOutBufferPurgationPkts	1.3.6.1.4.1.2011.5.25.41.1.6.1.1.33	Counter64	read-only	The number of sended Frames which is purged from the buffer because of long time
hwIfSdhStatTable	1.3.6.1.4.1.2011.5.25.41.1.6.2		not-accessible	Sdh/sonet Interface Statistic Table
hwIfSdhStatEntry	1.3.6.1.4.1.2011.5.25.41.1.6.2.1		not-accessible	Entry of Sdh/Sonet Interface Statistic Table
NUM hwIfSdhStatIfIndex	1.3.6.1.4.1.2011.5.25.41.1.6.2.1.1	InterfaceIndex	not-accessible	The index of sdh/sonet interface
C64 hwIfSdhStatInCRCPkts	1.3.6.1.4.1.2011.5.25.41.1.6.2.1.2	Counter64	read-only	The number of recieved Packets which have CRC checking errors
C64 hwIfSdhStatInShortPkts	1.3.6.1.4.1.2011.5.25.41.1.6.2.1.3	Counter64	read-only	The number of recieved Packets whose length is under minimal length
C64 hwIfSdhStatInLongPkts	1.3.6.1.4.1.2011.5.25.41.1.6.2.1.4	Counter64	read-only	The number of recieved Packets whose length is over maximum length
C64 hwIfSdhStatOutOverRunPkts	1.3.6.1.4.1.2011.5.25.41.1.6.2.1.5	Counter64	read-only	The number of sent Packets whose queue overflow
C64 hwIfSdhStatOutUnderRunPkts	1.3.6.1.4.1.2011.5.25.41.1.6.2.1.6	Counter64	read-only	The number of sent Packets whose queue underflow
INT hwIfSdhIfStatReset	1.3.6.1.4.1.2011.5.25.41.1.6.2.1.7	INTEGER	read-write	Reset the Statistic information Counter
hwIfAtmStatTable	1.3.6.1.4.1.2011.5.25.41.1.6.3		not-accessible	Atm Interface Statistic Table
hwIfAtmStatEntry	1.3.6.1.4.1.2011.5.25.41.1.6.3.1		not-accessible	Entry of Atm Interface Statistic Table
NUM hwIfAtmStatIfIndex	1.3.6.1.4.1.2011.5.25.41.1.6.3.1.1	InterfaceIndex	not-accessible	The index of atm interface
C64 hwIfAtmStatInGoodCells	1.3.6.1.4.1.2011.5.25.41.1.6.3.1.2	Counter64	read-only	The number of good cells recieved
C64 hwIfAtmStatInIdleCells	1.3.6.1.4.1.2011.5.25.41.1.6.3.1.3	Counter64	read-only	The number of idle cells recieved
C64 hwIfAtmStatInCorrectedCells	1.3.6.1.4.1.2011.5.25.41.1.6.3.1.4	Counter64	read-only	The number of recieved cells whitch have been corrected.
C64 hwIfAtmStatInUncorrectedCells	1.3.6.1.4.1.2011.5.25.41.1.6.3.1.5	Counter64	read-only	The number of recieved cells whitch can not be corrected.
C64 hwIfAtmStatOutGoodCells	1.3.6.1.4.1.2011.5.25.41.1.6.3.1.6	Counter64	read-only	The number of good cells sent
C64 hwIfAtmStatOutIdleCells	1.3.6.1.4.1.2011.5.25.41.1.6.3.1.7	Counter64	read-only	The number of idle cells sent
INT hwIfAtmIfStatReset	1.3.6.1.4.1.2011.5.25.41.1.6.3.1.8	INTEGER	read-write	Reset the Statistic information Counter
hwIfMonitorObject	1.3.6.1.4.1.2011.5.25.41.1.7
hwIfMonitorThresholdTable	1.3.6.1.4.1.2011.5.25.41.1.7.1		not-accessible	Alarm monitor table
hwIfMonitorThresholdEntry	1.3.6.1.4.1.2011.5.25.41.1.7.1.1		not-accessible	Entry of alarm monitor table
NUM hwIfMonitorIndex	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.1	InterfaceIndex	not-accessible	Index of alarm monitor table
C64 hwIfMonitorCrcErrorStatistics	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.2	Counter64	read-only	Crc error statistics value
I32 hwIfMonitorCrcErrorThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.3	Integer32	read-write	Crc error alarm threshold,default value is 3 and 0 is an invalid value
I32 hwIfMonitorCrcErrorInterval	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.4	Integer32	read-write	Crc error alarm interval time(unit is second),default value is 10s and 0 is an invalid value
C64 hwIfMonitorSdhErrorStatistics	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.5	Counter64	read-only	Sdh error statistics value only for B3
I32 hwIfMonitorSdhErrorThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.6	Integer32	read-write	Sdh error alarm threshold,only for B3,default value is 3 and 0 is an invalid value
I32 hwIfMonitorSdhErrorInterval	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.7	Integer32	read-write	Sdh error alarm interval time(unit is second),only for B3,default value is 10s and 0 is an invalid value
I32 hwIfMonitorInputRatePercentage	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.8	Integer32	read-only	Input rate percentage value
I32 hwIfMonitorInputRateThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.9	Integer32	read-write	Input rate alarm threshold,default value is 100
I32 hwIfMonitorOutputRatePercentage	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.10	Integer32	read-only	Output rate percentage value
I32 hwIfMonitorOutputRateThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.11	Integer32	read-write	Output rate alarm threshold,default value is 100
C64 hwIfMonitorPauseFrameStatistics	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.12	Counter64	read-only	Pause frame statistics value
I32 hwIfMonitorPauseFrameThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.13	Integer32	read-write	Pause frame alarm threshold,and 0 is an invalid value
I32 hwIfMonitorPauseFrameInterval	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.14	Integer32	read-write	Pause frame alarm interval time(unit is second),and 0 is an invalid value
I32 hwIfMonitorDelayValue	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.15	Integer32	read-write	Delay value
I32 hwIfMonitorDelayThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.16	Integer32	read-write	Delay alarm threshold
I32 hwIfMonitorJitterValue	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.17	Integer32	read-write	Jitter value
I32 hwIfMonitorJitterThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.18	Integer32	read-write	Jitter alarm threshold
STR hwIfMonitorName	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.19	DisplayString	read-only	Interface's name of alarm monitor table
C64 hwIfMonitorSdhB1ErrorStatistics	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.20	Counter64	read-only	Sdh B1 error statistics value
I32 hwIfMonitorSdhB1ErrorThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.21	Integer32	read-write	Sdh B1 error alarm threshold,default value is 3
I32 hwIfMonitorSdhB1ErrorInterval	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.22	Integer32	read-write	Sdh B1 error alarm interval time(unit is second),default value is 10s
C64 hwIfMonitorSdhB2ErrorStatistics	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.23	Counter64	read-only	Sdh B2 error statistics value
I32 hwIfMonitorSdhB2ErrorThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.24	Integer32	read-write	Sdh error B2 alarm threshold,default value is 3
I32 hwIfMonitorSdhB2ErrorInterval	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.25	Integer32	read-write	Sdh B2 error alarm interval time(unit is second),default value is 10s
C64 hwIfMonitorSymbolErrorStatistics	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.26	Counter64	read-only	Symbol error statistics value
I32 hwIfMonitorSymbolErrorThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.27	Integer32	read-write	Symbol error alarm threshold,default value is 3
I32 hwIfMonitorSymbolErrorInterval	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.28	Integer32	read-write	Symbol error alarm interval time(unit is second),default value is 10s
C64 hwIfMonitorBadBytesErrorStatistics	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.40	Counter64	read-only	Description.
I32 hwIfMonitorBadBytesErrorThreshold	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.41	Integer32	read-write	Description.
I32 hwIfMonitorBadBytesErrorInterval	1.3.6.1.4.1.2011.5.25.41.1.7.1.1.42	Integer32	read-write	Description.
hwIfMonitorGeneral	1.3.6.1.4.1.2011.5.25.41.1.8
ENA hwIfMonitorCrcEnabledStatus	1.3.6.1.4.1.2011.5.25.41.1.8.1	EnabledStatus	read-write	Enalbe or disable the crc error monitor, and the default value is disable.
ENA hwIfMonitorSdhEnabledStatus	1.3.6.1.4.1.2011.5.25.41.1.8.2	EnabledStatus	read-write	Enalbe or disable the sdh error monitor, and the default value is disable.
ENA hwIfMonitorInputRateEnabledStatus	1.3.6.1.4.1.2011.5.25.41.1.8.3	EnabledStatus	read-write	Enalbe or disable the input rate monitor, and the default value is disable.
ENA hwIfMonitorOutputRateEnabledStatus	1.3.6.1.4.1.2011.5.25.41.1.8.4	EnabledStatus	read-write	Enalbe or disable the output rate monitor, and the default value is disable.
ENA hwIfMonitorHalfDuplexEnabledStatus	1.3.6.1.4.1.2011.5.25.41.1.8.5	EnabledStatus	read-write	Enalbe or disable the half duplex monitor, and the default value is disable.
ENA hwIfMonitorPauseRisingEnabledStatus	1.3.6.1.4.1.2011.5.25.41.1.8.6	EnabledStatus	read-write	Enalbe or disable the pause frame rising monitor, and the default value is disable.
ENA hwIfMonitorPauseContinuingEnabledStatus	1.3.6.1.4.1.2011.5.25.41.1.8.7	EnabledStatus	read-write	Enalbe or disable the pause frame continuing monitor, and the default value is disable.
ENA hwifMonitorBadBytesEnabledStatus	1.3.6.1.4.1.2011.5.25.41.1.8.8	EnabledStatus	read-write	Description.
hwAdminVrrpMemberIf	1.3.6.1.4.1.2011.5.25.41.1.9
I32 hwIfFlowChangeTime	1.3.6.1.4.1.2011.5.25.41.1.9.1	Integer32	accessible-for-notify	The time indicates when the interface's flow status changes.
hwAdminVrrpMemberIfTable	1.3.6.1.4.1.2011.5.25.41.1.9.2		not-accessible	The interface bound to VRRP table.
hwAdminVrrpMemberIfEntry	1.3.6.1.4.1.2011.5.25.41.1.9.2.1		not-accessible	Entries of the interface bound to VRRP table.
NUM hwAdminVrrpMemberIfIndex	1.3.6.1.4.1.2011.5.25.41.1.9.2.1.1	InterfaceIndex	not-accessible	The number of the interface.
I32 hwAdminVrrpVrid	1.3.6.1.4.1.2011.5.25.41.1.9.2.1.2	Integer32	read-create	The administrator VRRP vrid.
NUM hwAdminVrrpIfIndex	1.3.6.1.4.1.2011.5.25.41.1.9.2.1.3	InterfaceIndex	read-create	The administrator VRRP's configure interface index.
INT hwAdminVrrpMemberIfFlowStatus	1.3.6.1.4.1.2011.5.25.41.1.9.2.1.4	INTEGER	read-only	Current flow status of interface. 1:up 2:down
ROW hwAdminVrrpMemberIfRowStatus	1.3.6.1.4.1.2011.5.25.41.1.9.2.1.5	RowStatus	read-create	Current operation status of the row.
hwIfFluxLimit	1.3.6.1.4.1.2011.5.25.41.1.10
hwIfFluxLimitTable	1.3.6.1.4.1.2011.5.25.41.1.10.1		not-accessible	Flux limit table
hwIfFluxLimitEntry	1.3.6.1.4.1.2011.5.25.41.1.10.1.1		not-accessible	Entry of flux limit table
NUM hwIfFluxIfIndex	1.3.6.1.4.1.2011.5.25.41.1.10.1.1.1	InterfaceIndex	not-accessible	Interface Index, same as ifIndex.
VLA hwIfFluxVlanId	1.3.6.1.4.1.2011.5.25.41.1.10.1.1.2	VlanIdOrNone	not-accessible	Vlan ID. 0 is the default value
HWD hwIfFluxDirection	1.3.6.1.4.1.2011.5.25.41.1.10.1.1.3	HWDirectionType	read-create	Limit direction: inbound (1) outbound (2)
INT hwIfFluxLimitType	1.3.6.1.4.1.2011.5.25.41.1.10.1.1.4	INTEGER	read-create	Flux limit type: broadcastSuppression(1),multicastSuppression(2),unknownUnicastSuppression(3).
I32 hwIfFluxCir	1.3.6.1.4.1.2011.5.25.41.1.10.1.1.5	Integer32	read-create	Committed Information Rate. Unit: kbps. software QoS: 8..155000 hardware QoS: 100..10000000
I32 hwIfFluxCbs	1.3.6.1.4.1.2011.5.25.41.1.10.1.1.6	Integer32	read-create	Committed Burst Size. Unit: byte software QoS: 1875..19375000 hardware QoS: 64..33554432
ROW hwIfFluxRowStatus	1.3.6.1.4.1.2011.5.25.41.1.10.1.1.7	RowStatus	read-create	RowStatus. Three actions are used: active, createAndGo, destroy
hwIfDiffServ	1.3.6.1.4.1.2011.5.25.41.1.11
hwIfDiffServTable	1.3.6.1.4.1.2011.5.25.41.1.11.1		not-accessible	The table describes the different service mode of interfaces.
hwIfDiffServEntry	1.3.6.1.4.1.2011.5.25.41.1.11.1.1		not-accessible	Interface different service mode attribute configuration.
NUM hwIfDiffServIndex	1.3.6.1.4.1.2011.5.25.41.1.11.1.1.1	InterfaceIndex	not-accessible	The index of L2 interface.
INT hwIfDiffServMode	1.3.6.1.4.1.2011.5.25.41.1.11.1.1.2	INTEGER	read-only	Different service mode of the interface binding to a VLL, default is uniform.
INT hwIfDiffServServiceClass	1.3.6.1.4.1.2011.5.25.41.1.11.1.1.3	INTEGER	read-only	PHB in the ingress PE, the value must be be,af1,af2,af3,af4,ef,cs6,cs7.
INT hwIfDiffServColor	1.3.6.1.4.1.2011.5.25.41.1.11.1.1.4	INTEGER	read-only	Remarked color of packet in the ingress PE, the value must be green,yellow,red.
hwIfQuery	1.3.6.1.4.1.2011.5.25.41.1.12
hwIfQueryTable	1.3.6.1.4.1.2011.5.25.41.1.12.1		not-accessible	Interface name table of private MIB.
hwIfQueryEntry	1.3.6.1.4.1.2011.5.25.41.1.12.1.1		not-accessible	Entries of private interface name table.
OCT hwIfName	1.3.6.1.4.1.2011.5.25.41.1.12.1.1.1	OCTET STRING	not-accessible	The name of the interface.The value of this object must be the interface name assigned by the local device.
NUM hwIfIndex	1.3.6.1.4.1.2011.5.25.41.1.12.1.1.2	InterfaceIndex	read-only	The index of the interface. An index uniquely identifies an interface.
hwLogicIfAttrib	1.3.6.1.4.1.2011.5.25.41.1.13
hwLogicIfTable	1.3.6.1.4.1.2011.5.25.41.1.13.1		not-accessible	Logic interface table.
hwLogicIfEntry	1.3.6.1.4.1.2011.5.25.41.1.13.1.1		not-accessible	Logic interface table.
NUM hwLogicIfIndex	1.3.6.1.4.1.2011.5.25.41.1.13.1.1.1	InterfaceIndexOrZero	not-accessible	Indicates the interface index. The interface index to be created must be 0. Then the system automatically allocates an interface index.
NUM hwLogicIfMainIndex	1.3.6.1.4.1.2011.5.25.41.1.13.1.1.11	InterfaceIndexOrZero	read-only	Indicates the interface index of the main interface to which the sub-interface belongs. For other interfaces, the interface index is 0.
INT hwLogicIfType	1.3.6.1.4.1.2011.5.25.41.1.13.1.1.12	INTEGER	read-create	Indicates the interface type.
STR hwLogicIfName	1.3.6.1.4.1.2011.5.25.41.1.13.1.1.13	DisplayString	read-create	Indicates the interface name. The interface name must be a name without blank spaces and Tab characters.
INT hwLogicIfParaOne	1.3.6.1.4.1.2011.5.25.41.1.13.1.1.14	INTEGER	read-create	Indicates the extended attribute of the logical interface. The extended attribute takes effect only on the ATM sub-interface. The default extended attribute is P2MP. For sub-interfaces of other types, none is returned after the Get operation.
ROW hwLogicIfRowStatus	1.3.6.1.4.1.2011.5.25.41.1.13.1.1.51	RowStatus	read-create	Indicates the status of the row.
hwLogicIfHelpTable	1.3.6.1.4.1.2011.5.25.41.1.13.2		not-accessible	Logic interface help table.
hwLogicIfHelpEntry	1.3.6.1.4.1.2011.5.25.41.1.13.2.1		not-accessible	Logic interface help table.
INT hwLogicIfhelpType	1.3.6.1.4.1.2011.5.25.41.1.13.2.1.1	INTEGER	read-only	Indicates the types of logical interfaces that can be queried.
OCT hwLogicIfChassisNumber	1.3.6.1.4.1.2011.5.25.41.1.13.2.1.2	OCTET STRING	read-only	Indicates the ID of the chassis that supports the creation of the specified logical interface.
OCT hwLogicIfSlotNumber	1.3.6.1.4.1.2011.5.25.41.1.13.2.1.3	OCTET STRING	read-only	Indicates the ID of the slot that supports the creation of the specified logical interface.
OCT hwLogicIfCardNumber	1.3.6.1.4.1.2011.5.25.41.1.13.2.1.4	OCTET STRING	read-only	Indicates the number of the card that supports the creation of the specified logical interface.
I32 hwLogicIfMin	1.3.6.1.4.1.2011.5.25.41.1.13.2.1.5	Integer32	read-only	Indicates the minimum port number of the specified logical interface.
I32 hwLogicIfMax	1.3.6.1.4.1.2011.5.25.41.1.13.2.1.6	Integer32	read-only	Indicates the maximum port number of the specified logical interface.
I32 hwLogicIfTotal	1.3.6.1.4.1.2011.5.25.41.1.13.2.1.7	Integer32	read-only	Indicates the maximum number of the specified logical interface.
hwLogicIfDynamicHelpTable	1.3.6.1.4.1.2011.5.25.41.1.13.3		not-accessible	Logic interface dynamic help table.
hwLogicIfDynamicHelpEntry	1.3.6.1.4.1.2011.5.25.41.1.13.3.1		not-accessible	Logic interface dynamic help table.
INT hwLogicDynamicIfhelpType	1.3.6.1.4.1.2011.5.25.41.1.13.3.1.1	INTEGER	read-only	Indicates the types of logical interfaces that can be queried.
I32 hwLogicDynamicIfChassisNumber	1.3.6.1.4.1.2011.5.25.41.1.13.3.1.2	Integer32	read-only	Indicates the ID of the chassis that that can be queried.
I32 hwLogicDynamicIfSlotNumber	1.3.6.1.4.1.2011.5.25.41.1.13.3.1.3	Integer32	read-only	Indicates the ID of the slot that can be queried.
I32 hwLogicDynamicIfCardNumber	1.3.6.1.4.1.2011.5.25.41.1.13.3.1.4	Integer32	read-only	Indicates the ID of the card that can be queried.
I32 hwLogicDynamicIfMin	1.3.6.1.4.1.2011.5.25.41.1.13.3.1.5	Integer32	read-only	Indicates the minimum port number of the specified logical interface.
I32 hwLogicDynamicIfMax	1.3.6.1.4.1.2011.5.25.41.1.13.3.1.6	Integer32	read-only	Indicates the maximum port number of the specified logical interface.
I32 hwLogicDynamicIfTotal	1.3.6.1.4.1.2011.5.25.41.1.13.3.1.7	Integer32	read-only	Indicates the maximum number of the specified logical interface.
hwCppsObjects	1.3.6.1.4.1.2011.5.25.41.1.14
ENA hwCppsGlobalEnable	1.3.6.1.4.1.2011.5.25.41.1.14.1	EnabledStatus	read-write	Whether statistic function is enabled globally, and the default value is disable.
hwCppsInterfaceTable	1.3.6.1.4.1.2011.5.25.41.1.14.2		not-accessible	CPU packet and byte statistic interface configuration table.
hwCppsInterfaceEntry	1.3.6.1.4.1.2011.5.25.41.1.14.2.1		not-accessible	The entry of hwCppsInterfaceTable.
NUM hwCppsInterfaceIndex	1.3.6.1.4.1.2011.5.25.41.1.14.2.1.1	InterfaceIndex	not-accessible	Index number of the interface.
ENA hwCppsPortPvcEnable	1.3.6.1.4.1.2011.5.25.41.1.14.2.1.2	EnabledStatus	read-write	Whether statistic function is enabled on PVC.
ENA hwCppsPortVlanEnable	1.3.6.1.4.1.2011.5.25.41.1.14.2.1.3	EnabledStatus	read-write	Whether statistic function is enabled on VLAN.
hwCppsIfStatisticsTable	1.3.6.1.4.1.2011.5.25.41.1.14.3		not-accessible	CPU packet and byte statistic interface table.
hwCppsIfStatisticsEntry	1.3.6.1.4.1.2011.5.25.41.1.14.3.1		not-accessible	The entry of hwCppsIfStatisticsTable.
NUM hwCppsIfStatisticsIndex	1.3.6.1.4.1.2011.5.25.41.1.14.3.1.1	InterfaceIndex	not-accessible	Index number of the interface.
C64 hwCppsInterfacePktStatisic	1.3.6.1.4.1.2011.5.25.41.1.14.3.1.2	Counter64	read-only	Packet statistic information of the interface sent to CPU.
C64 hwCppsInterfaceByteStatisic	1.3.6.1.4.1.2011.5.25.41.1.14.3.1.3	Counter64	read-only	Byte statistic information of the interface sent to CPU.
INT hwCppsResetInterfaceStatisic	1.3.6.1.4.1.2011.5.25.41.1.14.3.1.4	INTEGER	read-write	Whether to reset statistics.
hwCppsAtmPvcTable	1.3.6.1.4.1.2011.5.25.41.1.14.4		not-accessible	CPU packet and byte statistic ATM PVC table.
hwCppsAtmPvcEntry	1.3.6.1.4.1.2011.5.25.41.1.14.4.1		not-accessible	The entry of hwCppsAtmPvcTable.
NUM hwCppsAtmIfIndex	1.3.6.1.4.1.2011.5.25.41.1.14.4.1.1	InterfaceIndex	not-accessible	Index number of the interface.
OID hwCppsAtmVpi	1.3.6.1.4.1.2011.5.25.41.1.14.4.1.2	AtmVpIdentifier	not-accessible	VPI.
OID hwCppsAtmVci	1.3.6.1.4.1.2011.5.25.41.1.14.4.1.3	AtmVcIdentifier	not-accessible	VCI.
C64 hwCppsAtmPvcPktStatisic	1.3.6.1.4.1.2011.5.25.41.1.14.4.1.4	Counter64	read-only	Packet statistic information of the PVC sent to CPU.
C64 hwCppsAtmPvcByteStatisic	1.3.6.1.4.1.2011.5.25.41.1.14.4.1.5	Counter64	read-only	Byte statistic information of the PVC sent to CPU.
INT hwCppsResetAtmPvcStatisic	1.3.6.1.4.1.2011.5.25.41.1.14.4.1.6	INTEGER	read-write	Whether to reset statistics.
hwCppsPortVlanTable	1.3.6.1.4.1.2011.5.25.41.1.14.5		not-accessible	CPU packet and byte statistic port VLAN table.
hwCppsPortVlanEntry	1.3.6.1.4.1.2011.5.25.41.1.14.5.1		not-accessible	The entry of hwCppsPortVlanTable.
NUM hwCppsPortIndex	1.3.6.1.4.1.2011.5.25.41.1.14.5.1.1	InterfaceIndex	not-accessible	Index number of the interface.
VLA hwCppsVlanId	1.3.6.1.4.1.2011.5.25.41.1.14.5.1.2	VlanIdOrNone	not-accessible	VLAN ID.
C64 hwCppsPortVlanPktStatisic	1.3.6.1.4.1.2011.5.25.41.1.14.5.1.3	Counter64	read-only	Packet statistic information of the port sent to CPU.
C64 hwCppsPortVlanByteStatisic	1.3.6.1.4.1.2011.5.25.41.1.14.5.1.4	Counter64	read-only	Byte statistic information of the port sent to CPU.
INT hwCppsResetPortVlanStatisic	1.3.6.1.4.1.2011.5.25.41.1.14.5.1.5	INTEGER	read-write	Whether to reset statistics.
hwPortIsolationGroupAttrib	1.3.6.1.4.1.2011.5.25.41.1.15
hwPortIsolationGroupTable	1.3.6.1.4.1.2011.5.25.41.1.15.1		not-accessible	Logic interface table.
hwPortIsolationGroupEntry	1.3.6.1.4.1.2011.5.25.41.1.15.1.1		not-accessible	Logic interface table.
I32 hwPortIsolationGroupIndex	1.3.6.1.4.1.2011.5.25.41.1.15.1.1.1	Integer32	not-accessible	ID of Port-Isolation-Group.
POR hwPortIsolationGroupPortList	1.3.6.1.4.1.2011.5.25.41.1.15.1.1.2	PortList	read-create	PortList of Port-Isolation-Group.
ROW hwPortIsolationGroupRowStatus	1.3.6.1.4.1.2011.5.25.41.1.15.1.1.3	RowStatus	read-create	Indicates the status of the row.
hwVTrunkAttr	1.3.6.1.4.1.2011.5.25.41.1.16
hwVTrunkIfTable	1.3.6.1.4.1.2011.5.25.41.1.16.1		not-accessible	The vtrunk table.
hwVTrunkIfEntry	1.3.6.1.4.1.2011.5.25.41.1.16.1.1		not-accessible	Entries of the vtrunk table.
NUM hwVTrunkIfIndex	1.3.6.1.4.1.2011.5.25.41.1.16.1.1.1	InterfaceIndex	not-accessible	The IfIndex of the VTrunk interface.
I32 hwVTrunkIfID	1.3.6.1.4.1.2011.5.25.41.1.16.1.1.2	Integer32	read-create	The identification of the VTrunk interface.It may identify VTrunk and is an index of the interface.
INT hwVTrunkIfType	1.3.6.1.4.1.2011.5.25.41.1.16.1.1.3	INTEGER	read-create	The type of the VTrunk interface includes pos-Trunk, cpos-Trunk, atm-trunk and atm-bundle.
ROW hwVTrunkIfRowStatus	1.3.6.1.4.1.2011.5.25.41.1.16.1.1.50	RowStatus	read-create	Current operation status of the row.
hwVTrunkMemAttr	1.3.6.1.4.1.2011.5.25.41.1.17
hwVTrunkMemTable	1.3.6.1.4.1.2011.5.25.41.1.17.1		not-accessible	VTrunk member attribute information table.
hwVTrunkMemEntry	1.3.6.1.4.1.2011.5.25.41.1.17.1.1		not-accessible	VTrunk member attribute information.
I32 hwVTrunkMemIfIndex	1.3.6.1.4.1.2011.5.25.41.1.17.1.1.1	Integer32	not-accessible	VTrunk port index.
I32 hwVTrunkIfnetIndex	1.3.6.1.4.1.2011.5.25.41.1.17.1.1.2	Integer32	read-create	The IfnetIndex of the VTrunk interface.
INT hwVTrunkValidEntry	1.3.6.1.4.1.2011.5.25.41.1.17.1.1.3	INTEGER	read-only	Valid Entries of VTrunk interface.
INT hwVTrunkOperstatus	1.3.6.1.4.1.2011.5.25.41.1.17.1.1.4	INTEGER	read-only	Status of operation, indicates port status. There are vtrunk_up(1) and vtrunk_down(2).It expresses whether port is shutdown.
INT hwVTrunkPortActive	1.3.6.1.4.1.2011.5.25.41.1.17.1.1.5	INTEGER	read-only	Active port of backup-access vtrunk or not 1: portInactive 2: portActive.
ROW hwVTrunkRowStatus	1.3.6.1.4.1.2011.5.25.41.1.17.1.1.50	RowStatus	read-create	Current operation status of the row.
hwMasterBackupTrunkSubinterfaceAttr	1.3.6.1.4.1.2011.5.25.41.1.18
hwMasterBackupTrunkSubinterfaceTable	1.3.6.1.4.1.2011.5.25.41.1.18.1		not-accessible	Master-Backup Trunk Subinterface attribute information table.
hwMasterBackupTrunkSubinterfaceEntry	1.3.6.1.4.1.2011.5.25.41.1.18.1.1		not-accessible	Master-Backup Trunk Subinterface attribute information.
NUM hwBackupTrunkIfIndex	1.3.6.1.4.1.2011.5.25.41.1.18.1.1.1	InterfaceIndex	not-accessible	This object indicates index of master/backup trunk sub-interface.
INT hwBackupStatus	1.3.6.1.4.1.2011.5.25.41.1.18.1.1.2	INTEGER	read-only	The value of this object identifies backupStatus of master/backup trunk sub-interface.
INT hwRevertiveMode	1.3.6.1.4.1.2011.5.25.41.1.18.1.1.3	INTEGER	read-write	The value of this object identifies revertive-mode of master/backup trunk sub-interface.
I32 hwWtrTime	1.3.6.1.4.1.2011.5.25.41.1.18.1.1.4	Integer32	read-write	The value of this object identifies the wait-to-restore time of master/backup trunk sub-interface.
VLA hwFlushVlanId	1.3.6.1.4.1.2011.5.25.41.1.18.1.1.5	VlanIdOrNone	read-write	This object indicates VLAN ID carried in a FlushPDU.
hwVaspPort	1.3.6.1.4.1.2011.5.25.41.1.19
hwVaspPortPeerMacTable	1.3.6.1.4.1.2011.5.25.41.1.19.1		not-accessible	Vasp port peer MAC table.
hwVaspPortPeerMacEntry	1.3.6.1.4.1.2011.5.25.41.1.19.1.1		not-accessible	Vasp port peer MAC table entry.
NUM hwVaspPortIfIndex	1.3.6.1.4.1.2011.5.25.41.1.19.1.1.1	InterfaceIndex	not-accessible	The index of interface.
STR hwVaspPortName	1.3.6.1.4.1.2011.5.25.41.1.19.1.1.2	DisplayString	read-only	The name of vasp port.
PHY hwVaspPortPeerMac	1.3.6.1.4.1.2011.5.25.41.1.19.1.1.3	PhysAddress	read-only	The peer MAC of port.
hwIFExtTrapObjects	1.3.6.1.4.1.2011.5.25.41.1.20
INT hwLinkDownReason	1.3.6.1.4.1.2011.5.25.41.1.20.1	INTEGER	accessible-for-notify	The reason code of link changes.
STR hwMainIfName	1.3.6.1.4.1.2011.5.25.41.1.20.2	DisplayString	accessible-for-notify	The main interface name.
STR hwCfmOverPhysicalName	1.3.6.1.4.1.2011.5.25.41.1.20.3	DisplayString	accessible-for-notify	The configuration of the interface board or interface card is restored.
hwIFExtConformance	1.3.6.1.4.1.2011.5.25.41.2
hwIFExtGroups	1.3.6.1.4.1.2011.5.25.41.2.1
hwTrunkIfGroup	1.3.6.1.4.1.2011.5.25.41.2.1.1			A collection of objects indicating information of IP address of interface, contain IP address, IP address mask and IP address acquiring method.
hwIfIpAddressGroup	1.3.6.1.4.1.2011.5.25.41.2.1.2			A collection of objects indicating attribute of the Trunk interface.
hwIFExtGroup	1.3.6.1.4.1.2011.5.25.41.2.1.3			A collection of objects indicating attribute of interface extended.
hwTrunkMemGroup	1.3.6.1.4.1.2011.5.25.41.2.1.4			Trunk member attribute Group, now only can set hwTrunkPortWeight and hwTrunkPortStandby. hwTrunkSelectStatus and hwTrunkDeleteFlag can't be set. These attributes are for extend.
hwIFFlowStatGroup	1.3.6.1.4.1.2011.5.25.41.2.1.5			A collection of objects indicating interval time of interface flow stat.
hwAdminVrrpMemberIfGroup	1.3.6.1.4.1.2011.5.25.41.2.1.6			A collection of objects indicating attribute of the interface track administrator VRRP.
hwIfEtherStatGroup	1.3.6.1.4.1.2011.5.25.41.2.1.7			Interface statistic Group.
hwIfMonitorThresholdGroup	1.3.6.1.4.1.2011.5.25.41.2.1.8			Alarm Monitor Group.
hwIfMonitorGeneralGroup	1.3.6.1.4.1.2011.5.25.41.2.1.9			Alarm Monitor Enable Group.
hwIfFluxLimitGroup	1.3.6.1.4.1.2011.5.25.41.2.1.10			Flux limit Group.
hwIfDiffServGroup	1.3.6.1.4.1.2011.5.25.41.2.1.11			Interface statistic Group.
hwIfQueryGroup	1.3.6.1.4.1.2011.5.25.41.2.1.12			Interface name Group.
hwLogicIfAttrGroup	1.3.6.1.4.1.2011.5.25.41.2.1.13			Logic interface table Group.
hwIfIpUnnumberedGroup	1.3.6.1.4.1.2011.5.25.41.2.1.14			Logic interface table Group.
hwLinkModeChangeAutoCreateIfGroup	1.3.6.1.4.1.2011.5.25.41.2.1.15			Interface time slot Group.
hwCppsGlobalEnableGroup	1.3.6.1.4.1.2011.5.25.41.2.1.16			A collection of objects indicating global CPU packet statistic function.
hwCppsInterfaceGroup	1.3.6.1.4.1.2011.5.25.41.2.1.17			A collection of objects providing interface configuration function.
hwCppsIfStatisticsGroup	1.3.6.1.4.1.2011.5.25.41.2.1.18			A collection of objects providing packet and byte statistic of the interface sent to CPU.
hwCppsAtmPvcGroup	1.3.6.1.4.1.2011.5.25.41.2.1.19			A collection of objects providing packet and byte statistic for the pvc sent to CPU.
hwCppsPortVlanGroup	1.3.6.1.4.1.2011.5.25.41.2.1.20			A collection of objects providing packet and byte statistic for the port sent to CPU.
hwPortIsolationGroup	1.3.6.1.4.1.2011.5.25.41.2.1.21			Port Isolation Group.
hwVTrunkIfGroup	1.3.6.1.4.1.2011.5.25.41.2.1.22			VTrunk attribute Group.
hwVTrunkMemGroup	1.3.6.1.4.1.2011.5.25.41.2.1.23			VTrunk member attribute Group.
hwLogicIfHelpTableGroup	1.3.6.1.4.1.2011.5.25.41.2.1.24			Logic interface help table Group.
hwSubInterfaceBackupTrunkGroup	1.3.6.1.4.1.2011.5.25.41.2.1.25			SubInterfaceBackupTrunk attribute Group.
hwVaspPortGroup	1.3.6.1.4.1.2011.5.25.41.2.1.26			The vasp port group.
hwLogicIfDynamicHelpTableGroup	1.3.6.1.4.1.2011.5.25.41.2.1.27			Logic interface Dynamic help table Group.
hwIFExtCompliances	1.3.6.1.4.1.2011.5.25.41.2.2
hwIFExtCompliance	1.3.6.1.4.1.2011.5.25.41.2.2.1			The compliance statement for entities implementing Huawei extended interface management MIB.
hwIFExtTraps	1.3.6.1.4.1.2011.5.25.41.3
NTF hwTrunkWorkingSwitch	1.3.6.1.4.1.2011.5.25.41.3.1			hwTrunkWorkingSwitch. 1.hwTrunkIfID: The identification of the Trunk interface; 2.hwTrunkIfWorkingState: Current working state of backup-access trunk. Index: hwTrunkIndex.
NTF hwLacpNegotiateFailed	1.3.6.1.4.1.2011.5.25.41.3.2			The member of LAG neither can take over PDU nor transmit PDUs. Send this trap when LACP protocol negotiation fails. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is the name of the trunk in the ifXTable of IF-MIB. 3.ifName: It is the name of the port in the ifXTable of IF-MIB. Indexes: 1.hwTrunkIndex; 2.ifIndex.
NTF hwLacpTotalLinkLoss	1.3.6.1.4.1.2011.5.25.41.3.3			Total loss of link bandwidth: it means that there is no member in the LAG group and the trap of MNCD(Member not Collecting/Distributing) occurs. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is in the ifXTable of IF-MIB. Index: hwTrunkIndex.
NTF hwLacpPartialLinkLoss	1.3.6.1.4.1.2011.5.25.41.3.4			Part loss of link bandwidth: it means that some members in the LAG group aren't in the working-state, making the number of ports in working-state smaller than the hwTrunkIfMinLinkNum. The trap of PLL(Partial Link Loss) will be restrained by the trap of TLL(Total Link Loss). 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is in the ifXTable of IF-MIB. Index: hwTrunkIndex.
NTF hwIfFlowDown	1.3.6.1.4.1.2011.5.25.41.3.5			This notification indicates the time when the interface's flow status changes to flow down,and the reason.
NTF hwIfFlowUp	1.3.6.1.4.1.2011.5.25.41.3.6			This notification indicates the time when the interface's flow status changes to flow up,and the reason.
NTF hwIfNameChange	1.3.6.1.4.1.2011.5.25.41.3.7			When a single-chassis device is upgraded to a multi-chassis device, the interface information is changed and then the system sends a trap.
NTF hwIfNameChangeResume	1.3.6.1.4.1.2011.5.25.41.3.8			When a multi-chassis restore a single-chassis device, the interface information is changed and then the system sends a trap.
NTF hwExtLinkDown	1.3.6.1.4.1.2011.5.25.41.3.9			This notification indicates the time when the member interface link status changes to down.The ifDescr indicates the name of the member interface,the hwIFExtMemberOf indicates the name of main interface.
NTF hwExtLinkUp	1.3.6.1.4.1.2011.5.25.41.3.10			This notification indicates the time when the member interface link status changes to up.The ifDescr indicates the name of the member interface,the hwIFExtMemberOf indicates the name of main interface.
NTF hwLoopbackBlock	1.3.6.1.4.1.2011.5.25.41.3.11			This notification indicates block state of the interface.
NTF hwLoopbackResume	1.3.6.1.4.1.2011.5.25.41.3.12			This notification indicates normal state of the interface.
NTF hwLacpNegotiateResume	1.3.6.1.4.1.2011.5.25.41.3.13			Negotiation failure alarm is resumed. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is the name of the trunk in the ifXTable of IF-MIB. 3.ifName: It is the name of the port in the ifXTable of IF-MIB. Indexes: 1.hwTrunkIndex; 2.ifIndex.
NTF hwLacpTotalLinkLossResume	1.3.6.1.4.1.2011.5.25.41.3.14			Link bandwidth lost totally is resumed. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is in the ifXTable of IF-MIB. Index: hwTrunkIndex.
NTF hwLacpPartialLinkLossResume	1.3.6.1.4.1.2011.5.25.41.3.15			Link bandwidth lost partly is resumed. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is in the ifXTable of IF-MIB. Index: hwTrunkIndex.
NTF hwTrunkSubIfStateToMaster	1.3.6.1.4.1.2011.5.25.41.3.24			This notification indicates BackupState of the Trunk subinterface. 1.hwIfName: The identification of the Trunk subinterface; 2.hwBackupStatus: Current working state of Trunk subinterface.
NTF hwTrunkSubIfStateToSlave	1.3.6.1.4.1.2011.5.25.41.3.25			This notification indicates BackupState of the Trunk subinterface. 1.hwIfName: The identification of the Trunk subinterface; 2.hwBackupStatus: Current working state of Trunk subinterface.
NTF hwEntityExtCfmOverSlot	1.3.6.1.4.1.2011.5.25.41.3.26			The hwEntityExtCfmOverSlot notification will be displayed when the configuration of an interface board is restored. The object hwCfmOverPhysicalName idicates the name of the interface board.
NTF hwEntityExtCfmOverCard	1.3.6.1.4.1.2011.5.25.41.3.27			The hwEntityExtCfmOverCard notification will be displayed when the configuration of an interface card is restored. The object hwCfmOverPhysicalName idicates the name of the interface card.
NTF hwExtAllMemberDownNotify	1.3.6.1.4.1.2011.5.25.41.3.28			This notification indicates the time when the last member interface link status changes to down. The ifName indicates the name of the Trunk interface.
NTF hwExtAllMemberDownResume	1.3.6.1.4.1.2011.5.25.41.3.29			This notification indicates the time when the first member interface link status changes to up. The ifName indicates the name of the Trunk interface.
NTF hwIfControlFlapSuppress	1.3.6.1.4.1.2011.5.25.41.3.31			This notification indicates the time when the interface's status changes from unsuppress to suppress.
NTF hwIfControlFlapResume	1.3.6.1.4.1.2011.5.25.41.3.32			This notification indicates the time when the interface's status changes from suppress to unsuppress.
NTF hwExtInterfaceDelete	1.3.6.1.4.1.2011.5.25.41.3.33			This notification indicates the time when the interface was deleted.
hwMonitorNotifications	1.3.6.1.4.1.2011.5.25.41.4
NTF hwIfMonitorCrcErrorRising	1.3.6.1.4.1.2011.5.25.41.4.1			Crc error alarm notification
NTF hwIfMonitorCrcErrorResume	1.3.6.1.4.1.2011.5.25.41.4.2			Crc error alarm resume
NTF hwIfMonitorSdhErrorRising	1.3.6.1.4.1.2011.5.25.41.4.3			Sdh error alarm notification only for B3
NTF hwIfMonitorSdhErrorResume	1.3.6.1.4.1.2011.5.25.41.4.4			Sdh error alarm resume only for B3
NTF hwIfMonitorInputRateRising	1.3.6.1.4.1.2011.5.25.41.4.5			Input rate alarm notification
NTF hwIfMonitorInputRateResume	1.3.6.1.4.1.2011.5.25.41.4.6			Input rate alarm resume
NTF hwIfMonitorOutputRateRising	1.3.6.1.4.1.2011.5.25.41.4.7			Output rate alarm notification
NTF hwIfMonitorOutputRateResume	1.3.6.1.4.1.2011.5.25.41.4.8			Output rate alarm resume
NTF hwIfMonitorHalfDuplexRising	1.3.6.1.4.1.2011.5.25.41.4.9			Interface half duplex alarm norification
NTF hwIfMonitorPauseFrameRising	1.3.6.1.4.1.2011.5.25.41.4.10			Pause frame alarm notification
NTF hwIfMonitorPauseFrameRisingResume	1.3.6.1.4.1.2011.5.25.41.4.11			Pause frame alarm resume
NTF hwIfPortControlUp	1.3.6.1.4.1.2011.5.25.41.4.12			Control Up alarm notification
NTF hwIfPortControlDown	1.3.6.1.4.1.2011.5.25.41.4.13			Control Down alarm notification
NTF hwIfMonitorSdhB1ErrorRising	1.3.6.1.4.1.2011.5.25.41.4.14			Sdh B1 error alarm notification
NTF hwIfMonitorSdhB1ErrorResume	1.3.6.1.4.1.2011.5.25.41.4.15			Sdh B1 error alarm resume
NTF hwIfMonitorSdhB2ErrorRising	1.3.6.1.4.1.2011.5.25.41.4.16			Sdh B2 error alarm notification
NTF hwIfMonitorSdhB2ErrorResume	1.3.6.1.4.1.2011.5.25.41.4.17			Sdh B2 error alarm resume
NTF hwIfMonitorSymbolErrorRising	1.3.6.1.4.1.2011.5.25.41.4.18			Symbol error alarm notification
NTF hwIfMonitorSymbolErrorResume	1.3.6.1.4.1.2011.5.25.41.4.19			Crc error alarm resume
NTF hwIfMonitorBadBytesErrorRising	1.3.6.1.4.1.2011.5.25.41.4.40			Description.
NTF hwIfMonitorBadBytesErrorResume	1.3.6.1.4.1.2011.5.25.41.4.41			Description.
hwIFExtTrapConformance	1.3.6.1.4.1.2011.5.25.41.5
hwIFExtTrapGroups	1.3.6.1.4.1.2011.5.25.41.5.1
hwIFExtTrapGroup	1.3.6.1.4.1.2011.5.25.41.5.1.1			IF Trap Group.
hwMonitorTrapGroup	1.3.6.1.4.1.2011.5.25.41.5.1.2			Monitor Trap Group.
hwIFIpNotifications	1.3.6.1.4.1.2011.5.25.41.6
NTF hwIfIpAddressChange	1.3.6.1.4.1.2011.5.25.41.6.1			IP Trap Group. The trap will be generated when the primary IP address of an interface changes.

RFC description

Extends interface management with configuration of IP attributes, interface trunking, and extended interface properties for Huawei devices.

Start monitoring Huawei router or switch (extended interface/SDH/VRRP statistics) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-IF-EXT-MIB