All MIBs › HUAWEI-SYS-MAN-MIB
Organization: Huawei Technologies Co.,Ltd.
Last Updated: 2015-03-10
Category: Device Management, Domain: System Management, Vendor: Huawei
Description: Huawei system management MIB for managing system configuration, file system operations, and device lifecycle management.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-SYS-MAN-MIB?
HUAWEI-SYS-MAN-MIB is a Huawei vendor-private MIB (registered at hwDatacomm.19) covering system-level management on VRP-based Huawei datacom devices: system clock, the active configuration file and system image file, scheduled or manual reload actions, in-service software patching (ISSU), and a broad set of change/failure notifications. It defines objects such as hwSysCurCFGFileIndex, hwSysCurImageIndex, and hwSysCurPatchFileIndex in the hwSysCurTable to track which configuration, image, and patch are currently active, hwSysReloadSchedule/hwSysReloadAction for reboot control, and detailed patch-lifecycle status through the HWPatchErrorType textual convention (covering fetch, activate, run, deactivate, and remove failure codes). Because it spans both configuration state and event notifications (hwSysPafChangeNotification, hwSysLicenseChangeNotification, hwSystemBoardExclude), monitoring it lets an NMS confirm which firmware/config/patch set is running and detect unplanned reloads, patch failures, or license/board changes. It depends on HUAWEI-MIB for its hwDatacomm registration point and is deployed across the broader family of Huawei VRP-based devices; administrators managing such devices typically consult the HUAWEI-SYS-MAN-MIB MIB to correlate configuration, patch, and reload events.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-SYS-MAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei Datacom switches/routers (VRP-based platforms)
Monitoring Examples
An operator polls hwSysCurTable to confirm hwSysCurCFGFileIndex and hwSysCurPatchFileIndex point to the expected configuration and patch versions after a maintenance window, watching for hwSysPafChangeNotification or an unexpected hwSysReloadAction trigger; a patch entry surfacing an HWPatchErrorType such as activeStateInvalid or runBadState would indicate the patch failed to apply cleanly and the device may be running unpatched code.
What Can Be Monitored
- current configuration/image/patch file indices
- system reload schedule and action state
- patch activation error codes/status
- ISSU (in-service software upgrade) state
- system reboot reason
- license/PAF change notifications
This MIB depends on
Related MIBs
Imported Objects
From ENTITY-MIB
| PhysicalIndex | |
| entPhysicalIndex | OBJECT-TYPE |
| entPhysicalName | OBJECT-TYPE |
From HUAWEI-MIB
| hwDatacomm | OBJECT-IDENTITY |
From P-BRIDGE-MIB
| EnabledStatus |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| RowPointer | |
| RowStatus | |
| TEXTUAL-CONVENTION |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| huaweiSystemManMIB | 1.3.6.1.4.1.2011.5.25.19 | The HUAWEI-SYS-MAN-MIB contains objects to manage the system. The module defines the information about system, such as system time, the current configuration file and system image file, system reload actions, and notifications. By querying the system time, configuration files and system image files, NMS can reboot the device in the specified time and the specified configuration and system image. | ||
| huaweiSystemManMIBObjects | 1.3.6.1.4.1.2011.5.25.19.1 | |||
| hwSysClock | 1.3.6.1.4.1.2011.5.25.19.1.1 | |||
| DAT hwSysLocalClock | 1.3.6.1.4.1.2011.5.25.19.1.1.1 | DateAndTime | read-only | This object indicates the local time of the device. |
| hwSysCurrent | 1.3.6.1.4.1.2011.5.25.19.1.2 | |||
| hwSysCurTable | 1.3.6.1.4.1.2011.5.25.19.1.2.1 | not-accessible | The current status of system. A configuration file and an image file are used to describe the current status. | |
| hwSysCurEntry | 1.3.6.1.4.1.2011.5.25.19.1.2.1.1 | not-accessible | An entry of hwSysCurTable. It is indexed by hwSysCurEntPhysicalIndex. | |
| I32 hwSysCurEntPhysicalIndex | 1.3.6.1.4.1.2011.5.25.19.1.2.1.1.1 | Integer32 | not-accessible | The value of this object identifies the system index. |
| I32 hwSysCurCFGFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.2.1.1.2 | Integer32 | read-only | The value of this object identifies the index of the configuration file in the configuration file list. The value is referenced from hwSysCFGFileTable. The value ranges from 1 to 2147483647. |
| I32 hwSysCurImageIndex | 1.3.6.1.4.1.2011.5.25.19.1.2.1.1.3 | Integer32 | read-only | The value of this object identifies the index of the image file in the image file list. The value is referenced from hwSysImageTable. The value ranges from 1 to 2147483647. |
| I32 hwSysCurPafFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.2.1.1.4 | Integer32 | read-only | The value of this object identifies the index of the PAF file in the PAF file list. |
| I32 hwSysCurLicenseIndex | 1.3.6.1.4.1.2011.5.25.19.1.2.1.1.5 | Integer32 | read-only | The value of this object identifies the index of the license file in the license file list. |
| I32 hwSysCurPatchFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.2.1.1.6 | Integer32 | read-only | The value of this object identifies the index of the patch file in the patch file list. |
| I32 hwSysCurVoiceFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.2.1.1.7 | Integer32 | read-only | The value of this object identifies the index of the configuration file in the configuration file list. The value is referenced from hwSysCFGFileTable. The value ranges from 1 to 2147483647. |
| hwSysReload | 1.3.6.1.4.1.2011.5.25.19.1.3 | |||
| I32 hwSysReloadSchedule | 1.3.6.1.4.1.2011.5.25.19.1.3.1 | Integer32 | read-write | The value of this object identifies the record number used when the device restarts. The value ranges from 0 to 2147483647. After the system restarts, the value returns to 0. 0: initial value. 65536: main board schedule method. |
| INT hwSysReloadAction | 1.3.6.1.4.1.2011.5.25.19.1.3.2 | INTEGER | read-write | The value of this object identifies restart types. 1: reloadUnavailable 2: reloadOnSchedule, indicating periodical restart 3: reloadAtOnce, indicating immediate restart without considering hwSysReloadScheduleTime 4: reloadCancel, indicating that all the planned restart activities are cancelled. If hwSysReloadSchedule is invalid or the rows that hwSysReloadScheduleEntry and hwSysReloadSchedule point to are not activated, all the restart activities are ignored and an inconsistent value is returned. When the restart of the system is complete or no restart activities exist, the value of this object is reloadUnavailable(1). |
| hwSysReloadScheduleTable | 1.3.6.1.4.1.2011.5.25.19.1.3.3 | not-accessible | A reload parameters table. | |
| hwSysReloadScheduleEntry | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1 | not-accessible | Entry of hwSysReloadScheduleTable. | |
| I32 hwSysReloadScheduleIndex | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.1 | Integer32 | not-accessible | The value of this object identifies the index of the instance. The value ranges from 0 to 2147483647. |
| PHY hwSysReloadEntity | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.2 | PhysicalIndex | read-create | This object indicates the index of the restarting entity. The value is referred to from entPhysicalTable. 1. When get/get-next, 1 means active main board, 2 means slave main board, 65535 means other board. 2. When set, 2 means slave main board, other values mean active main board. |
| I32 hwSysReloadCfgFile | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.3 | Integer32 | read-create | The value of this object identifies the configuration file used after the restart. The value is limited by hwSysCFGFileTable. The value ranges from 0 to 2147483647. The default value is 0, which means the configuration file remains unchanged. |
| I32 hwSysReloadImage | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.4 | Integer32 | read-create | The value of this object identifies the image file used after the restart. The value is limited by hwSysImageTable. The value ranges from 1 to 2147483647. |
| STR hwSysReloadReason | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.5 | DisplayString | read-create | This object indicates the cause of the restart. The value is a string of 0 to 255 characters. After the system restarts, the character string is deleted. |
| DAT hwSysReloadScheduleTime | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.6 | DateAndTime | read-create | This object indicates the time of the restart. The only valid value of this object is an 8-byte string which indicates the local time of the switch. The maximum scheduled time is 30 days from the current system clock time. If the value set is earlier than the value of hwSysLocalClock or beyond the maximum scheduled time limit, a bad value error occurred. The value of all-zero octet strings indicates system restart at once if the reload action is reloadOnSchedule(1). |
| ROW hwSysReloadRowStatus | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.7 | RowStatus | read-create | If one of values of hwSysReloadEntity, hwSysReloadCfgFile and hwSysReloadImage is invalid, the value of hwSysReloadRowStatus cannot be set to 'active'. A valid entry means the specified element is available in the current system. Reload an entity indexed by hwSysReloadEntity with the startup configuration file and the image may be not allowed. Herein the entry is invalid. |
| I32 hwSysReloadPafFile | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.8 | Integer32 | read-create | The value of this object identifies the PAF file used after the restart. |
| I32 hwSysReloadLicenseFile | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.9 | Integer32 | read-create | The value of this object identifies the license file used after the restart. |
| I32 hwSysReloadPatchFile | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.10 | Integer32 | read-create | The value of this object identifies the patch file used after the restart. |
| INT hwSysReloadPatchState | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.11 | INTEGER | read-create | The value of this object identifies the running status of the patch at the next startup. That is, whether the loaded patch is in the Run state at the next startup. run(1): indicates that the loaded patch is in the Run state at the next startup. unused(255): indicates that the loaded patch is in the original state at the next startup. |
| INT hwSysReloadOperateDestType | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.12 | INTEGER | read-create | This object indicates the object to be restarted. |
| STR hwSysReloadOperateDestIndex | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.13 | DisplayString | read-create | This object indicates the index of the board needs to be restarted. The get/get-next result is 'unused'. but, you can't use 'unused' to set. |
| I32 hwSysReloadVoiceFile | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.14 | Integer32 | read-create | The value of this object identifies the license file used after the restart. |
| I32 hwSysReloadAndroidFile | 1.3.6.1.4.1.2011.5.25.19.1.3.3.1.15 | Integer32 | read-create | The value of this object identifies the android file used after the restart. The value is limited by hwSysAndroidFileTable. The value ranges from 0 to 2147483647. The default value is 0, which means the android file remains unchanged. |
| INT hwSysReboot | 1.3.6.1.4.1.2011.5.25.19.1.3.4 | INTEGER | read-write | The value of this object identifies the restart of the master and slave boards. Values are as follows unused(1): indicates that this value is not used. Generally, this value is read. rebootAllRoute(2): indicates that the integrated device is restarted. rebootSlave(3): indicates that the slave board is restarted. slaveSwitch(4): indicates that the switchover between the main and slave boards is performed. |
| ENA hwSysSlaveSwitchEnable | 1.3.6.1.4.1.2011.5.25.19.1.3.5 | EnabledStatus | read-write | The value of this object identifies whether the switchover between the main and the slave boards is enabled. enable(1): indicates that the switchover between the main and slave boards is enabled. disable(2): indicates that the switchover between the main and slave boards is not enabled. |
| STR hwSysLatestRebootErrorInfo | 1.3.6.1.4.1.2011.5.25.19.1.3.6 | DisplayString | read-only | This object indicates the cause of the last restart. |
| hwSysSlaveSwitchTable | 1.3.6.1.4.1.2011.5.25.19.1.3.7 | not-accessible | A slave switchover enable parameters table. | |
| hwSysSlaveSwitchEntry | 1.3.6.1.4.1.2011.5.25.19.1.3.7.1 | not-accessible | Entry of hwSysSlaveSwitchTable. | |
| I32 hwSysSlaveSwitchIndex | 1.3.6.1.4.1.2011.5.25.19.1.3.7.1.1 | Integer32 | not-accessible | The value of the object identifies the index of the table. |
| STR hwSysSlaveSwitchChassisNum | 1.3.6.1.4.1.2011.5.25.19.1.3.7.1.2 | DisplayString | read-write | The value of the object identifies the chassis number. |
| INT hwSysSlaveSwitchOperType | 1.3.6.1.4.1.2011.5.25.19.1.3.7.1.3 | INTEGER | read-write | Operation type. The object has the following values: unused(1): means the default value. slaveswitch(2): perform force switchover. slaveswitchlock(3): enable the force switchover, this value should be used with the object of hwSysSlaveSwitchEnableStatus. |
| ENA hwSysSlaveSwitchEnableStatus | 1.3.6.1.4.1.2011.5.25.19.1.3.7.1.4 | EnabledStatus | read-write | The enable status of switchover for AMB (Active Main Board) and SMB (Standby Main Board). enable(1): enable the force switchover. disable(2): disable the force switchover. |
| STR hwSysSlaveSwitchSrc | 1.3.6.1.4.1.2011.5.25.19.1.3.7.1.5 | DisplayString | read-write | The source slot for slave switchover. |
| STR hwSysSlaveSwitchDst | 1.3.6.1.4.1.2011.5.25.19.1.3.7.1.6 | DisplayString | read-write | The destination slot for slave switchover. |
| I32 hwSysDelayReboot | 1.3.6.1.4.1.2011.5.25.19.1.3.8 | Integer32 | read-write | Restart the device at a delayed time. The delayed time can be set up to 43200 minutes. The node is used to set the delayed time, cancel the setting, or check the status of the delayed restart. If a value within the range of 0 to 43200 is entered, the delayed time is set. If the value 65535 is entered, the setting is cancelled. During system reboot, a return value 65534 is displayed if the Get or Walk operation is performed. Other values are invalid. |
| hwSysImage | 1.3.6.1.4.1.2011.5.25.19.1.4 | |||
| I32 hwSysImageNum | 1.3.6.1.4.1.2011.5.25.19.1.4.1 | Integer32 | read-only | The value of this object identifies the number of image files. The object calculates the number of image files given by hwSysImageTable. The value ranges from 0 to 2147483647. |
| hwSysImageTable | 1.3.6.1.4.1.2011.5.25.19.1.4.2 | not-accessible | The system image management table. | |
| hwSysImageEntry | 1.3.6.1.4.1.2011.5.25.19.1.4.2.1 | not-accessible | A system image entry. Each entry consists of information of a system image. hwSysImageIndex exclusively decides an image file. | |
| I32 hwSysImageIndex | 1.3.6.1.4.1.2011.5.25.19.1.4.2.1.1 | Integer32 | not-accessible | The value of this object identifies the index of the image file. |
| STR hwSysImageName | 1.3.6.1.4.1.2011.5.25.19.1.4.2.1.2 | DisplayString | read-only | This object indicates the name of the image file. A file name containing path and suffix is a string of 4 to 64 characters. |
| I32 hwSysImageSize | 1.3.6.1.4.1.2011.5.25.19.1.4.2.1.3 | Integer32 | read-only | The value of this object identifies the size of the image file. The value ranges from 0 to 2147483647, in bytes. The size depends on the actual file and is limited by the physical storage device. |
| STR hwSysImageLocation | 1.3.6.1.4.1.2011.5.25.19.1.4.2.1.4 | DisplayString | read-only | This object indicates the location of the image file, namely the path. |
| STR hwSysImageVersion | 1.3.6.1.4.1.2011.5.25.19.1.4.2.1.5 | DisplayString | read-only | The value of this object identifies the version of the image file. |
| STR hwSysImageReason | 1.3.6.1.4.1.2011.5.25.19.1.4.2.1.6 | DisplayString | read-only | The value of this object identifies the error cause of the image file. |
| hwSysCFGFile | 1.3.6.1.4.1.2011.5.25.19.1.5 | |||
| I32 hwSysCFGFileNum | 1.3.6.1.4.1.2011.5.25.19.1.5.1 | Integer32 | read-only | The value of this object identifies the number of configuration files. The object calculates the number of configuration files given by hwSysCFGFileTable. The value ranges from 0 to 2147483647. |
| hwSysCFGFileTable | 1.3.6.1.4.1.2011.5.25.19.1.5.2 | not-accessible | A table of configuration files in this system. | |
| hwSysCFGFileEntry | 1.3.6.1.4.1.2011.5.25.19.1.5.2.1 | not-accessible | A configuration file entry. Each entry consists of information of a configuration file. hwSysCFGFileIndex exclusively decides a configuration file. | |
| I32 hwSysCFGFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.5.2.1.1 | Integer32 | not-accessible | The value of this object identifies the index of the configuration file. |
| STR hwSysCFGFileName | 1.3.6.1.4.1.2011.5.25.19.1.5.2.1.2 | DisplayString | read-only | This object indicates the name of the configuration file. Currently, Huawei products support two formats of configuration files, namely, .CFG and .ZIP. A file name containing path and suffix is a string of 5 to 64 characters. |
| I32 hwSysCFGFileSize | 1.3.6.1.4.1.2011.5.25.19.1.5.2.1.3 | Integer32 | read-only | The value of this object identifies the size of the configuration file. The value ranges from 0 to 2147483647. |
| STR hwSysCFGFileLocation | 1.3.6.1.4.1.2011.5.25.19.1.5.2.1.4 | DisplayString | read-only | This object indicates the location of the configuration file, namely, the path. |
| STR hwSysCFGFileReason | 1.3.6.1.4.1.2011.5.25.19.1.5.2.1.5 | DisplayString | read-only | This object indicates the error cause of the configuration file. |
| hwSysPafFile | 1.3.6.1.4.1.2011.5.25.19.1.6 | |||
| I32 hwSysPafFileNum | 1.3.6.1.4.1.2011.5.25.19.1.6.1 | Integer32 | read-only | The value of this object identifies the number of PAF files in the system. |
| hwSysPafFileTable | 1.3.6.1.4.1.2011.5.25.19.1.6.2 | not-accessible | A table of paf files in this system. | |
| hwSysPafFileEntry | 1.3.6.1.4.1.2011.5.25.19.1.6.2.1 | not-accessible | A paf file entry. Each entry consists of information of a paf file. hwSysPafFileIndex exclusively decides a configuration file. | |
| I32 hwSysPafFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.6.2.1.1 | Integer32 | not-accessible | The value of this object identifies the index of this table. |
| STR hwSysPafFileName | 1.3.6.1.4.1.2011.5.25.19.1.6.2.1.2 | DisplayString | read-only | This object indicates the name of the PAF file. |
| I32 hwSysPafFileSize | 1.3.6.1.4.1.2011.5.25.19.1.6.2.1.3 | Integer32 | read-only | The value of this object identifies the size of the PAF file. |
| STR hwSysPafFileLocation | 1.3.6.1.4.1.2011.5.25.19.1.6.2.1.4 | DisplayString | read-only | This object indicates the position of the PAF file. |
| STR hwSysPafFileVersion | 1.3.6.1.4.1.2011.5.25.19.1.6.2.1.5 | DisplayString | read-only | This object indicates the version of the PAF file. |
| hwSysLicenseFile | 1.3.6.1.4.1.2011.5.25.19.1.7 | |||
| I32 hwSysLicenseFileNum | 1.3.6.1.4.1.2011.5.25.19.1.7.1 | Integer32 | read-only | The value of this object identifies the number of license files in the system. |
| hwSysLicenseFileTable | 1.3.6.1.4.1.2011.5.25.19.1.7.2 | not-accessible | A table of license files in this system. | |
| hwSysLicenseFileEntry | 1.3.6.1.4.1.2011.5.25.19.1.7.2.1 | not-accessible | A license file entry. Each entry consists of information of a license file. hwSysLicenseFileIndex exclusively decides a configuration file. | |
| I32 hwSysLicenseFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.7.2.1.1 | Integer32 | not-accessible | The value of this object identifies the index of this table. |
| STR hwSysLicenseFileName | 1.3.6.1.4.1.2011.5.25.19.1.7.2.1.2 | DisplayString | read-only | This object indicates the name of the license file. |
| I32 hwSysLicenseFileSize | 1.3.6.1.4.1.2011.5.25.19.1.7.2.1.3 | Integer32 | read-only | This object indicates the size of the license file. |
| STR hwSysLicenseFileLocation | 1.3.6.1.4.1.2011.5.25.19.1.7.2.1.4 | DisplayString | read-only | This object indicates the position of the license file. |
| hwPatch | 1.3.6.1.4.1.2011.5.25.19.1.8 | |||
| hwPatchBase | 1.3.6.1.4.1.2011.5.25.19.1.8.1 | |||
| I32 hwPatchFileNum | 1.3.6.1.4.1.2011.5.25.19.1.8.1.1 | Integer32 | read-only | The value of this object identifies the number of patches in the system. |
| INT hwPatchRecordReset | 1.3.6.1.4.1.2011.5.25.19.1.8.1.2 | INTEGER | read-write | Clear the patch records. unused(1): unused. resetPatchHistory(2): clears the hwPatchHistoryTable record. resetPatchError(3): clears the hwPatchErrorTable record. |
| I32 hwPatchHistoryTableMax | 1.3.6.1.4.1.2011.5.25.19.1.8.1.3 | Integer32 | read-write | Set the size of hwPatchHistoryTable. |
| ENA hwPatchTrapEnble | 1.3.6.1.4.1.2011.5.25.19.1.8.1.4 | EnabledStatus | read-write | The value of this object determines whether to generate the trap of HUAWEI-SYS-MAN-MIB. enable(1): Trap is enabled. disable(2): Trap is not enabled. |
| I32 hwPatchErrorTableMax | 1.3.6.1.4.1.2011.5.25.19.1.8.1.5 | Integer32 | read-write | The value of this object identifies the maximum number of recorded errors supported by hwPatchErrorTable. |
| STR hwPatchId | 1.3.6.1.4.1.2011.5.25.19.1.8.1.6 | DisplayString | read-only | This object indicates the patch ID on the device. |
| STR hwPatchLatestId | 1.3.6.1.4.1.2011.5.25.19.1.8.1.7 | DisplayString | read-only | This object indicates the latest patch ID on the device. |
| INT hwPatchFailReason | 1.3.6.1.4.1.2011.5.25.19.1.8.1.8 | INTEGER | read-only | This object is an index that specifies patch fail reason. |
| hwPatchFileTable | 1.3.6.1.4.1.2011.5.25.19.1.8.2 | not-accessible | Patch file query table. | |
| hwPatchFileEntry | 1.3.6.1.4.1.2011.5.25.19.1.8.2.1 | not-accessible | Defines an entry in the hwPatchFileTable. | |
| U32 hwPatchFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.8.2.1.1 | Unsigned32 | not-accessible | The value of this object identifies the index of this table. |
| STR hwPatchFileName | 1.3.6.1.4.1.2011.5.25.19.1.8.2.1.2 | DisplayString | read-only | This object indicates the name of a patch file. |
| I32 hwPatchFileSize | 1.3.6.1.4.1.2011.5.25.19.1.8.2.1.3 | Integer32 | read-only | This object indicates the size of a patch file. |
| STR hwPatchFileLocation | 1.3.6.1.4.1.2011.5.25.19.1.8.2.1.4 | DisplayString | read-only | This object indicates the position of a patch file. |
| STR hwPatchFileVersion | 1.3.6.1.4.1.2011.5.25.19.1.8.2.1.5 | DisplayString | read-only | This object indicates the version of the patch file. |
| hwLoadPatchTable | 1.3.6.1.4.1.2011.5.25.19.1.8.4 | not-accessible | The load table of the patch file. Load the patch file to the memory: hwSlotIndex:The slot ID of the destination device to be loaded by the patch file, hwPatchFileIndex:The index of the patch file, If hwSlotIndex is 128, it indicates all slots of the device. | |
| hwLoadPatchEntry | 1.3.6.1.4.1.2011.5.25.19.1.8.4.1 | not-accessible | Defines an entry in the hwLoadPatchTable. | |
| INT hwPatchLoadDestType | 1.3.6.1.4.1.2011.5.25.19.1.8.4.1.1 | INTEGER | read-create | This object indicates the type of the board to be loaded with the patch. |
| STR hwPatchLoadDestIndex | 1.3.6.1.4.1.2011.5.25.19.1.8.4.1.2 | DisplayString | read-create | This object indicates the index of the board to be loaded with the patch. |
| INT hwPatchLoadState | 1.3.6.1.4.1.2011.5.25.19.1.8.4.1.3 | INTEGER | read-only | Patch loading state: loading(1):Patch is loading. success(2):Patch loading succeeded. failure(3):Patch loading failed. none(4):Patch and board do not match. |
| ROW hwLoadPatchRowState | 1.3.6.1.4.1.2011.5.25.19.1.8.4.1.51 | RowStatus | read-create | This object identifies the status of a row. |
| hwPatchInfo | 1.3.6.1.4.1.2011.5.25.19.1.8.5 | |||
| hwPatchTable | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1 | not-accessible | Running status transfer and query of the patch. If hwSlotIndex is 128, it indicates all slots of the device. If hwPatchNum is 65535, it indicates all patches of the specified slot. If hwPatchNum is 0, it indicates the NP patch of the specified slot. If hwPatchNum is in range from 1 to 200, it indicates the C patch of the specified slot. | |
| hwPatchEntry | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1 | not-accessible | Defines an entry in the hwPatchTable. | |
| I32 hwPatchSlotIndex | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.1 | Integer32 | not-accessible | The value of this object identifies the index of the slot. |
| U32 hwPatchIndex | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.2 | Unsigned32 | not-accessible | This object indicates the index of the patch. |
| STR hwPatchUsedFileName | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.3 | DisplayString | read-only | This object indicates the name of the patch file. |
| STR hwPatchVersion | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.4 | DisplayString | read-only | This object indicates the version of the patch file. |
| STR hwPatchDescription | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.5 | DisplayString | read-only | This object indicates the description of the patch. |
| STR hwPatchProgramVersion | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.6 | DisplayString | read-only | The value of the object identifies the version number of the host software. |
| I32 hwPatchFuncNum | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.7 | Integer32 | read-only | The value of this object identifies the number functions contained in the patch. |
| I32 hwPatchTextLen | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.8 | Integer32 | read-only | The value of this object identifies the length of the patch code. |
| I32 hwPatchDataLen | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.9 | Integer32 | read-only | The value of this object identifies the length of the patch data. |
| INT hwPatchType | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.10 | INTEGER | read-only | The value of this object identifies the patch type. hotCommon(1): indicates the common hot patch. hotTemporary(2): indicates the temporary hot patch. coolCommon(3): indicates the common cool patch. coolTemporary(4): indicates the temporary cool patch. |
| DAT hwPatchBuildTime | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.11 | DateAndTime | read-only | This object indicates the time when a patch file is built. |
| DAT hwPatchActiveTime | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.12 | DateAndTime | read-only | This object indicates the time when a patch file is activated. |
| INT hwPatchAdminStatus | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.13 | INTEGER | read-write | The value of this object identifies the operation status of a patch. Run (1): indicates that the patch status is Run. Active(2): indicates the patch status is Active. Deactive(3): indicates the patch status is Deactive. Delete(4): indicates that the patch is deleted. |
| INT hwPatchOperateState | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.14 | INTEGER | read-only | status of the patch. patchRunning(1): indicates that current status of the patch is Run. patchActive(2): indicates that current status of the patch is Active. patchDeactive(3): indicates that current status of the patch is Deactive. |
| INT hwPatchOperateDestType | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.15 | INTEGER | read-create | Patch operate object type,it combine with the hwPatchOperateDestIndex to note the operate object. |
| STR hwPatchOperateDestIndex | 1.3.6.1.4.1.2011.5.25.19.1.8.5.1.1.16 | DisplayString | read-create | Patch operate object index,it combine with chassis,the value of the hwPatchOperateDestType to note the operate object.hwPatchOperateDestIndex is value such as ccc1,clc2 etc. |
| hwPatchStateTable | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2 | not-accessible | The statistics information of the C patch area on each slot. | |
| hwPatchStateEntry | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1 | not-accessible | Defines an entry in the hwPatchStateTable. | |
| U32 hwPatchNumMax | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.1 | Unsigned32 | read-only | The value of this object identifies the maximum number of patches. |
| I32 hwPatchIdleNum | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.2 | Integer32 | read-only | The value of this object identifies the number of idle patches. |
| I32 hwPatchTextMax | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.3 | Integer32 | read-only | The value of this object identifies the size of the code in the patch area. |
| I32 hwPatchDataMax | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.4 | Integer32 | read-only | The value of this object identifies the size of the data in the patch area. |
| I32 hwPatchStateTextUsed | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.5 | Integer32 | read-only | The value of this object identifies the size of the used code in the patch area. |
| I32 hwPatchStateDataUsed | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.6 | Integer32 | read-only | The value of this object identifies the size of the used data in the patch area. |
| I32 hwPatchStateTotalPatchNum | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.7 | Integer32 | read-only | The value of this object identifies the total number of used patches. |
| I32 hwPatchStateTempPatchNum | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.8 | Integer32 | read-only | The value of this object identifies the total number of used temporary patches. |
| I32 hwPatchStateCommonPatchNum | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.9 | Integer32 | read-only | The value of this object identifies the total number of used common patches. |
| I32 hwPatchStateRuningPatchNum | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.10 | Integer32 | read-only | The value of this object identifies the number of patches in the Run state in the patch area. |
| I32 hwPatchStateActivePatchNum | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.11 | Integer32 | read-only | The value of this object identifies the number of patches in the Active state in the patch area. |
| I32 hwPatchStateDeactivePatchNum | 1.3.6.1.4.1.2011.5.25.19.1.8.5.2.1.12 | Integer32 | read-only | The value of this object identifies the number of patches in the Deactive state in the patch area. |
| hwPatchHistoryTable | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3 | not-accessible | Patch history table. | |
| hwPatchHistoryEntry | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3.1 | not-accessible | Defines an entry in the hwPatchHistoryTable. | |
| U32 hwPatchHistoryIndex | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3.1.1 | Unsigned32 | not-accessible | This object indicates the index of the table. |
| STR hwPatchHistoryProgrameVersion | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3.1.2 | DisplayString | read-only | The value of the object identifies the version number of the image file. |
| STR hwPatchHistoryVersion | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3.1.3 | DisplayString | read-only | The value of this object identifies the version of the patch. |
| I32 hwSlotId | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3.1.4 | Integer32 | read-only | The value of the object identifies the slot number of the patch. |
| I32 hwPatchBeginIndex | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3.1.5 | Integer32 | read-only | The value of this object identifies the start ID of the loaded patch. |
| I32 hwPatchEndIndex | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3.1.6 | Integer32 | read-only | The value of this object identifies the end ID of the loaded patch. |
| INT hwPatchHistoryAction | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3.1.7 | INTEGER | read-only | The value of this object identifies the patch status. |
| DAT hwPatchHistoryBeginTime | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3.1.8 | DateAndTime | read-only | This object indicates the start time of running the patch. |
| DAT hwPatchHistoryEndTime | 1.3.6.1.4.1.2011.5.25.19.1.8.5.3.1.9 | DateAndTime | read-only | This object indicates the end time of running the patch. |
| hwPatchErrorTable | 1.3.6.1.4.1.2011.5.25.19.1.8.5.4 | not-accessible | The error record table of patch operation. | |
| hwPatchErrorEntry | 1.3.6.1.4.1.2011.5.25.19.1.8.5.4.1 | not-accessible | Defines an entry in the hwPatchErrorTable. | |
| U32 hwPatchErrorIndex | 1.3.6.1.4.1.2011.5.25.19.1.8.5.4.1.1 | Unsigned32 | not-accessible | This object indicates the index of the patch error. |
| U32 hwPatchErrorSlot | 1.3.6.1.4.1.2011.5.25.19.1.8.5.4.1.2 | Unsigned32 | read-only | This object indicates the number of the slot related to a patch error. |
| STR hwPatchErrorPatchFileName | 1.3.6.1.4.1.2011.5.25.19.1.8.5.4.1.3 | DisplayString | read-only | This object indicates the index of the patch file when the patch has an error. |
| U32 hwPatchErrorPatchIndex | 1.3.6.1.4.1.2011.5.25.19.1.8.5.4.1.4 | Unsigned32 | read-only | This object indicates the index of the patch when the patch has an error. |
| HWP hwPatchErrorCode | 1.3.6.1.4.1.2011.5.25.19.1.8.5.4.1.5 | HWPatchErrorType | read-only | This object indicates the flag of the patch error. |
| hwBootRom | 1.3.6.1.4.1.2011.5.25.19.1.11 | |||
| hwBootRomTable | 1.3.6.1.4.1.2011.5.25.19.1.11.1 | not-accessible | Boot ROM startup parameter query table. | |
| hwBootRomEntry | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1 | not-accessible | Defines an entry in the hwBootRomTable. | |
| INT hwBootRomIndex | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.1 | INTEGER | not-accessible | The value of this object identifies the index of the BootROM table. |
| STR hwBootRomBootDevice | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.2 | DisplayString | read-only | This object indicates the name of the BootROM startup device. |
| I32 hwBootRomProcessorNo | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.3 | Integer32 | read-only | The value of this object identifies the number of the BootROM processor. |
| STR hwBootRomHostName | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.4 | DisplayString | read-only | The object indicates the name of the BootROM host. |
| STR hwBootRomFileName | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.5 | DisplayString | read-only | The object indicates the name of the BootROM file. |
| IP hwBootRomIpOnEthernet | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.6 | IpAddress | read-only | The object indicates the IP address of the BootROM Ethernet interface. |
| IP hwBootRomIpOnBackPlane | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.7 | IpAddress | read-only | The object indicates the IP address of the BootROM backplane. |
| IP hwBootRomHostIp | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.8 | IpAddress | read-only | The object indicates the IP address of the BootROM host. |
| IP hwBootRomGatewayIp | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.9 | IpAddress | read-only | The object indicates the IP address of the BootROM gateway. |
| STR hwBootRomUserName | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.10 | DisplayString | read-only | The object indicates the name of the BootROM user. |
| STR hwBootRomPassword | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.11 | DisplayString | read-only | The object indicates the BootROM password. |
| STR hwBootRomTargetName | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.12 | DisplayString | read-only | The object indicates the name of the BootROM target. |
| STR hwBootRomStartupScript | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.13 | DisplayString | read-only | The object indicates the BootROM startup script. |
| I32 hwBootRomXModemBaudRate | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.14 | Integer32 | read-only | The value of the object identifies the baud rate for transmitting the XModem data. |
| I32 hwBootRomVersion | 1.3.6.1.4.1.2011.5.25.19.1.11.1.1.15 | Integer32 | read-only | Boot ROM version. |
| hwSysUpgrade | 1.3.6.1.4.1.2011.5.25.19.1.12 | |||
| hwSysUpgradeTable | 1.3.6.1.4.1.2011.5.25.19.1.12.1 | not-accessible | ISSU upgrade table. | |
| hwSysUpgradeEntry | 1.3.6.1.4.1.2011.5.25.19.1.12.1.1 | not-accessible | Defines an entry in the hwSysUpgradeTable. | |
| I32 hwIssuIndex | 1.3.6.1.4.1.2011.5.25.19.1.12.1.1.1 | Integer32 | not-accessible | Set system issu table index. |
| INT hwIssuMode | 1.3.6.1.4.1.2011.5.25.19.1.12.1.1.2 | INTEGER | read-write | Set system issu upgrade mode. |
| STR hwIssuImageFile | 1.3.6.1.4.1.2011.5.25.19.1.12.1.1.3 | DisplayString | read-write | The name of the image file. |
| STR hwIssuPafFile | 1.3.6.1.4.1.2011.5.25.19.1.12.1.1.4 | DisplayString | read-write | The name of the paf file. |
| STR hwIssuLicenseFile | 1.3.6.1.4.1.2011.5.25.19.1.12.1.1.5 | DisplayString | read-write | The name of the license file. |
| STR hwIssuPatchFile | 1.3.6.1.4.1.2011.5.25.19.1.12.1.1.6 | DisplayString | read-write | The name of the patch file. |
| INT hwIssuState | 1.3.6.1.4.1.2011.5.25.19.1.12.2 | INTEGER | read-only | System issu upgrade state. |
| INT hwIssuConditionCheck | 1.3.6.1.4.1.2011.5.25.19.1.12.3 | INTEGER | read-only | System issu upgrade condition check. The default check result is normal. |
| hwSysSourceIndex | 1.3.6.1.4.1.2011.5.25.19.1.13 | |||
| hwSysSourceIndexTable | 1.3.6.1.4.1.2011.5.25.19.1.13.1 | not-accessible | System file Index query table. | |
| hwSysSourceIndexEntry | 1.3.6.1.4.1.2011.5.25.19.1.13.1.1 | not-accessible | Defines an entry in the hwBootRomTable. | |
| INT hwSysFileType | 1.3.6.1.4.1.2011.5.25.19.1.13.1.1.1 | INTEGER | not-accessible | The value of this object is an index that indicates the type of a file. |
| OCT hwSysFileName | 1.3.6.1.4.1.2011.5.25.19.1.13.1.1.2 | OCTET STRING | not-accessible | This object is an index that indicates the name of a file on the main control board. |
| I32 hwSysFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.13.1.1.3 | Integer32 | read-only | The value of this object identifies the index of a file in the specified table. If the value is 0, it indicates that this file does not exist in the specified table. |
| hwSysRebootInfo | 1.3.6.1.4.1.2011.5.25.19.1.14 | |||
| I32 hwSysRebootTimes | 1.3.6.1.4.1.2011.5.25.19.1.14.1 | Integer32 | read-only | The value of the device reboot times. |
| hwSysRebootRecordTable | 1.3.6.1.4.1.2011.5.25.19.1.14.2 | not-accessible | A reboot information record table. | |
| hwSysRebootRecordEntry | 1.3.6.1.4.1.2011.5.25.19.1.14.2.1 | not-accessible | Entry of hwSysReloadScheduleTable. | |
| I32 hwSysRebootRecordIndex | 1.3.6.1.4.1.2011.5.25.19.1.14.2.1.1 | Integer32 | not-accessible | The index of hwSysRebootRecordTable. |
| INT hwSysRebootReason | 1.3.6.1.4.1.2011.5.25.19.1.14.2.1.2 | INTEGER | read-only | The reason of system's reboot. |
| DAT hwSysRebootTime | 1.3.6.1.4.1.2011.5.25.19.1.14.2.1.3 | DateAndTime | read-only | The time at which the reboot action occurred. we will only take octet strings with length 8 for this object which indicates the local time of the switch. The maximum scheduled time is 30 days from the current system clock time. field octets contents range 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 |
| hwSysDeviceCheck | 1.3.6.1.4.1.2011.5.25.19.1.15 | |||
| INT hwSysDeviceCheckStart | 1.3.6.1.4.1.2011.5.25.19.1.15.1 | INTEGER | read-write | Set system check start. |
| INT hwSysDeviceCheckState | 1.3.6.1.4.1.2011.5.25.19.1.15.2 | INTEGER | read-only | Get system check state. |
| hwSysSwitchoverState | 1.3.6.1.4.1.2011.5.25.19.1.19 | |||
| hwSysSwitchoverStateTable | 1.3.6.1.4.1.2011.5.25.19.1.19.1 | not-accessible | Get switchover state of single-chassis | |
| hwSysSwitchoverStateEntry | 1.3.6.1.4.1.2011.5.25.19.1.19.1.1 | not-accessible | Entry of hwSysSwitchoverStateTable. | |
| I32 hwSysSwitchoverStateIndex | 1.3.6.1.4.1.2011.5.25.19.1.19.1.1.1 | Integer32 | not-accessible | This object indicates the index of the table. |
| I32 hwSysSwitchoverSlotId | 1.3.6.1.4.1.2011.5.25.19.1.19.1.1.2 | Integer32 | read-only | The value of this object identifies the slot number of the board. |
| INT hwSysSwitchoverBoardType | 1.3.6.1.4.1.2011.5.25.19.1.19.1.1.3 | INTEGER | read-only | The value of this object identifies the type of the board. |
| OCT hwSysSwitchoverInfo | 1.3.6.1.4.1.2011.5.25.19.1.19.1.1.4 | OCTET STRING | read-only | The value of this object descries the real-time information of HA status. |
| hwSysSwitchoverStateMultiTable | 1.3.6.1.4.1.2011.5.25.19.1.19.2 | not-accessible | Get switchover state of multi-chassis | |
| hwSysSwitchoverStateMultiEntry | 1.3.6.1.4.1.2011.5.25.19.1.19.2.1 | not-accessible | Entry of hwSysSwitchoverStateMultiTable. | |
| I32 hwSysMultiSwtStateIndex | 1.3.6.1.4.1.2011.5.25.19.1.19.2.1.1 | Integer32 | not-accessible | This object indicates the index of the table. |
| OCT hwSysMultiSwtChassisId | 1.3.6.1.4.1.2011.5.25.19.1.19.2.1.2 | OCTET STRING | read-only | The value of this object identifies the chassis id. |
| I32 hwSysMultiSwtSlotId | 1.3.6.1.4.1.2011.5.25.19.1.19.2.1.3 | Integer32 | read-only | The value of this object identifies the slot number of the board. |
| INT hwSysMultiSwtBoardType | 1.3.6.1.4.1.2011.5.25.19.1.19.2.1.4 | INTEGER | read-only | The value of this object identifies the type of the board. |
| OCT hwSysMultiSwtInfo | 1.3.6.1.4.1.2011.5.25.19.1.19.2.1.5 | OCTET STRING | read-only | The value of this object descries the real-time information of HA status. |
| hwSysVoiceFile | 1.3.6.1.4.1.2011.5.25.19.1.20 | |||
| I32 hwSysVoiceFileNum | 1.3.6.1.4.1.2011.5.25.19.1.20.1 | Integer32 | read-only | The value of this object identifies the number of configuration files. The object calculates the number of configuration files given by hwSysCFGFileTable. The value ranges from 0 to 2147483647. |
| hwSysVoiceFileTable | 1.3.6.1.4.1.2011.5.25.19.1.20.2 | not-accessible | A table of configuration files in this system. | |
| hwSysVoiceFileEntry | 1.3.6.1.4.1.2011.5.25.19.1.20.2.1 | not-accessible | A configuration file entry. Each entry consists of information of a configuration file. hwSysCFGFileIndex exclusively decides a configuration file. | |
| I32 hwSysVoiceFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.20.2.1.1 | Integer32 | not-accessible | The value of this object identifies the index of the configuration file. |
| STR hwSysVoiceFileName | 1.3.6.1.4.1.2011.5.25.19.1.20.2.1.2 | DisplayString | read-only | This object indicates the name of the configuration file. Currently, Huawei products support two formats of configuration files, namely, .CFG and .ZIP. A file name containing path and suffix is a string of 4 to 64 characters. |
| I32 hwSysVoiceFileSize | 1.3.6.1.4.1.2011.5.25.19.1.20.2.1.3 | Integer32 | read-only | The value of this object identifies the size of the configuration file. The value ranges from 0 to 2147483647. |
| STR hwSysVoiceFileLocation | 1.3.6.1.4.1.2011.5.25.19.1.20.2.1.4 | DisplayString | read-only | This object indicates the location of the configuration file, namely, the path. |
| hwSysWlanApUpgrade | 1.3.6.1.4.1.2011.5.25.19.1.24 | |||
| hwSysWlanApUpgradeCmd | 1.3.6.1.4.1.2011.5.25.19.1.24.1 | |||
| INT hwSysWlanApUpgradeMode | 1.3.6.1.4.1.2011.5.25.19.1.24.1.1 | INTEGER | read-write | The value of this object identifies the ap upgrade mode. The value ranges from 1 to 3. |
| STR hwSysWlanApUpgradeFileName | 1.3.6.1.4.1.2011.5.25.19.1.24.1.2 | DisplayString | read-write | The value of this object identifies the filename of the ap upgrade file. The value ranges from 1 to 127. |
| IP hwSysWlanApUpgradeServerIp | 1.3.6.1.4.1.2011.5.25.19.1.24.1.3 | IpAddress | read-write | The value of this object identifies server ip address in ipv4 format. |
| STR hwSysWlanApUpgradeServerUserName | 1.3.6.1.4.1.2011.5.25.19.1.24.1.4 | DisplayString | read-write | The value of this object identifies the username of server. The value ranges from 0 to 31. |
| STR hwSysWlanApUpgradeServerPassword | 1.3.6.1.4.1.2011.5.25.19.1.24.1.5 | DisplayString | read-write | The value of this object identifies the password of server. The value ranges from 0 to 63. |
| hwSysWlanApUpgradeStatus | 1.3.6.1.4.1.2011.5.25.19.1.24.2 | |||
| INT hwSysWlanApUpgradeProgressStatus | 1.3.6.1.4.1.2011.5.25.19.1.24.2.1 | INTEGER | read-write | The value of this object identifies the status of the upgrade or the last result of the upgrade. The value ranges from 0 to 10. |
| I32 hwSysWlanApUpgradeLoadProgress | 1.3.6.1.4.1.2011.5.25.19.1.24.2.2 | Integer32 | read-write | The value of this object identifies the progress of file downloading. The value ranges from 0 to 100. |
| I32 hwSysWlanApUpgradeStorageProgress | 1.3.6.1.4.1.2011.5.25.19.1.24.2.3 | Integer32 | read-write | The value of this object identifies the progress of file storaging. The value ranges from 0 to 100. |
| hwSysWlanApUpgradeNotifications | 1.3.6.1.4.1.2011.5.25.19.1.24.3 | |||
| NTF hwSysWlanApUpgradeBeginNotify | 1.3.6.1.4.1.2011.5.25.19.1.24.3.1 | This notification occurs when ap begin to update. | ||
| NTF hwSysWlanApUpgradeResultNotify | 1.3.6.1.4.1.2011.5.25.19.1.24.3.2 | This notification occurs when ap has updated successfully or failed. | ||
| NTF hwSysWlanApUpgradeUbootNotMatchNotify | 1.3.6.1.4.1.2011.5.25.19.1.24.3.3 | This notification occurs when ap uboot not match version. | ||
| NTF hwSysWlanApUpgradeAssistantPackageNotMatchNotify | 1.3.6.1.4.1.2011.5.25.19.1.24.3.4 | This notification occurs when ap upgrade-assistant-package not match version. | ||
| hwSysAndroidFile | 1.3.6.1.4.1.2011.5.25.19.1.25 | |||
| I32 hwSysAndroidFileNum | 1.3.6.1.4.1.2011.5.25.19.1.25.1 | Integer32 | read-only | The value of this object identifies the number of Android files. The object calculates the number of android files given by hwSysAndroidFileTable. The value ranges from 0 to 2147483647. |
| hwSysAndroidFileTable | 1.3.6.1.4.1.2011.5.25.19.1.25.2 | not-accessible | A table of android files in this system. | |
| hwSysAndroidFileEntry | 1.3.6.1.4.1.2011.5.25.19.1.25.2.1 | not-accessible | A android file entry. Each entry consists of information of a android file. hwSysAndroidFileIndex exclusively decides a android file. | |
| I32 hwSysAndroidFileIndex | 1.3.6.1.4.1.2011.5.25.19.1.25.2.1.1 | Integer32 | not-accessible | The value of this object identifies the index of the android file. |
| STR hwSysAndroidFileName | 1.3.6.1.4.1.2011.5.25.19.1.25.2.1.2 | DisplayString | read-only | This object indicates the name of the android file. Currently, Huawei products support one format of android files, namely, .BIN. A file name containing path and suffix is a string of 4 to 64 characters. |
| I32 hwSysAndroidFileSize | 1.3.6.1.4.1.2011.5.25.19.1.25.2.1.3 | Integer32 | read-only | The value of this object identifies the size of the android file. The value ranges from 0 to 2147483647. |
| STR hwSysAndroidFileLocation | 1.3.6.1.4.1.2011.5.25.19.1.25.2.1.4 | DisplayString | read-only | This object indicates the location of the android file, namely, the path. |
| STR hwSysAndroidFileReason | 1.3.6.1.4.1.2011.5.25.19.1.25.2.1.5 | DisplayString | read-only | This object indicates the error cause of the android file. |
| huaweiSystemManMIBNotifications | 1.3.6.1.4.1.2011.5.25.19.2 | |||
| NTF hwSysClockChangedNotification | 1.3.6.1.4.1.2011.5.25.19.2.1 | This object indicates the notification sent when the system clock changes. When the system clock changes, this trap is triggered. For example, the system clock is changed through command lines. | ||
| NTF hwSysReloadNotification | 1.3.6.1.4.1.2011.5.25.19.2.2 | This object indicates the restart notification. | ||
| NTF hwSysMasterHDError | 1.3.6.1.4.1.2011.5.25.19.2.3 | When the hard disk on master board cannot be read and written because of a certain error, the hard disk on master board is unregistered and the notification is sent. | ||
| NTF hwSysSlaveHDError | 1.3.6.1.4.1.2011.5.25.19.2.4 | When the hard disk on slave board cannot be read and written because of a certain error, the hard disk on slave board is unregistered and the notification is sent. | ||
| hwPatchTrap | 1.3.6.1.4.1.2011.5.25.19.2.5 | |||
| NTF hwPatchErrorTrap | 1.3.6.1.4.1.2011.5.25.19.2.5.1 | The trap is generated when the patch operation error occurs. | ||
| NTF hwPatchActiveOverTimeTrap | 1.3.6.1.4.1.2011.5.25.19.2.5.2 | The patch is not run within 24 hours after it is activated. | ||
| NTF hwPatchMalfunctionComebackTrap | 1.3.6.1.4.1.2011.5.25.19.2.5.3 | The patch operation is restored. | ||
| NTF hwPatchUpdateTrap | 1.3.6.1.4.1.2011.5.25.19.2.5.4 | The patch state change notification. | ||
| NTF hwSysMasterCfcardError | 1.3.6.1.4.1.2011.5.25.19.2.6 | When the cfcard on master board can't be read and written because of some error, the Cfcard on master board will be unregistered and the notification is sent. | ||
| NTF hwSysSlaveCfcardError | 1.3.6.1.4.1.2011.5.25.19.2.7 | When the cfcard on slave board can't be read and written because of some error, the Cfcard on slave board will be unregistered and the notification is sent. | ||
| NTF hwSysSlaveSwitchSuccessNotification | 1.3.6.1.4.1.2011.5.25.19.2.8 | This object indicates that the hwSysSlaveSwitchChassisNum chassis is successfully switched. | ||
| NTF hwSysSlaveSwitchFailNotification | 1.3.6.1.4.1.2011.5.25.19.2.9 | This object indicates that the hwSysSlaveSwitchChassisNum chassis fails to be switched. | ||
| NTF hwSysIssuNotification | 1.3.6.1.4.1.2011.5.25.19.2.10 | When the ISSU upgrade over, it will send success or failed message. | ||
| NTF hwPatchInstallFail | 1.3.6.1.4.1.2011.5.25.19.2.11 | The patch package install fail notification. | ||
| NTF hwPatchInstallFailClear | 1.3.6.1.4.1.2011.5.25.19.2.12 | The patch package install fail clear notification. | ||
| NTF hwSumUpgradeSuccess | 1.3.6.1.4.1.2011.5.25.19.2.13 | The patch package upgrade success notification | ||
| NTF hwSysCfgFileErrorNotification | 1.3.6.1.4.1.2011.5.25.19.2.14 | This object notifies that some error occurs when the configuration file is specified as the next startup configuration file. | ||
| NTF hwSysImageErrorNotification | 1.3.6.1.4.1.2011.5.25.19.2.15 | The image file upgrade fail notification. The first hwSysImageName indicates the current image file, and the second hwSysImageName indicates the next startup image file. | ||
| NTF hwSysPafChangeNotification | 1.3.6.1.4.1.2011.5.25.19.2.16 | This object indicates the notification sent when the system PAF file changes.The hwSysPafFileName indicates system PAF file, and the hwSysReloadEntity indicates the board type(1 means main board,2 means slave main board). | ||
| NTF hwSysLicenseChangeNotification | 1.3.6.1.4.1.2011.5.25.19.2.17 | This object indicates the notification sent when the system license file changes.The hwSysLicenseFileName indicates the system license file, and the hwSysReloadEntity indicates the board type(1 means main board,2 means slave main board). | ||
| NTF hwSystemBoardExclude | 1.3.6.1.4.1.2011.5.25.19.2.18 | The board(s) excluded during software upgrading | ||
| NTF hwSystemBoardExcludeClear | 1.3.6.1.4.1.2011.5.25.19.2.19 | The board(s) excluded retrieved during software upgrading | ||
| hwSysEvmTraps | 1.3.6.1.4.1.2011.5.25.19.2.20 | |||
| hwSysEvmTrapsObject | 1.3.6.1.4.1.2011.5.25.19.2.20.1 | |||
| OCT hwSysEvmRoleName | 1.3.6.1.4.1.2011.5.25.19.2.20.1.1 | OCTET STRING | accessible-for-notify | The value of this object identifies the number of Android files. The object calculates the number of android files given by hwSysAndroidFileTable. The value ranges from 0 to 2147483647. |
| OCT hwSysEvmDownloadFileName | 1.3.6.1.4.1.2011.5.25.19.2.20.1.2 | OCTET STRING | accessible-for-notify | The value of this object identifies the number of Android files. The object calculates the number of android files given by hwSysAndroidFileTable. The value ranges from 0 to 2147483647. |
| OCT hwSysEvmInstallFileName | 1.3.6.1.4.1.2011.5.25.19.2.20.1.3 | OCTET STRING | accessible-for-notify | The value of this object identifies the number of Android files. The object calculates the number of android files given by hwSysAndroidFileTable. The value ranges from 0 to 2147483647. |
| hwSysEvmNotifications | 1.3.6.1.4.1.2011.5.25.19.2.20.2 | |||
| NTF hwEvmVmAbnormalRunNotification | 1.3.6.1.4.1.2011.5.25.19.2.20.2.1 | The board(s) excluded retrieved during software upgrading | ||
| NTF hwEvmVmNotRunningNotification | 1.3.6.1.4.1.2011.5.25.19.2.20.2.2 | The board(s) excluded retrieved during software upgrading | ||
| NTF hwEvmVmAbnormalRestartNotification | 1.3.6.1.4.1.2011.5.25.19.2.20.2.3 | The board(s) excluded retrieved during software upgrading | ||
| NTF hwEvmDownloadFailedNotification | 1.3.6.1.4.1.2011.5.25.19.2.20.2.4 | The board(s) excluded retrieved during software upgrading | ||
| NTF hwEvmInstallFailedNotification | 1.3.6.1.4.1.2011.5.25.19.2.20.2.5 | The board(s) excluded retrieved during software upgrading | ||
| huaweiSystemManMIBConformance | 1.3.6.1.4.1.2011.5.25.19.3 | |||
| huaweiSystemManMIBCompliances | 1.3.6.1.4.1.2011.5.25.19.3.1 | |||
| huaweiSystemManMIBCompliance | 1.3.6.1.4.1.2011.5.25.19.3.1.1 | The compliance statement for entities which implement the Huawei system management MIB. | ||
| huaweiSystemManMIBGroups | 1.3.6.1.4.1.2011.5.25.19.3.2 | |||
| huaweiSysClockGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.1 | A collection of objects providing mandatory system reload. | ||
| huaweiSysReloadGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.2 | A collection of objects providing mandatory system clock information. | ||
| huaweiSysImageGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.3 | A collection of objects providing mandatory system image information. | ||
| huaweiSysCFGFileGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.4 | A collection of objects providing mandatory system configureation file information. | ||
| hwSysCurGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.5 | A collection of system current status. | ||
| huaweiSystemManNotificationGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.6 | A collection of notification. | ||
| huaweiSystemHDNotificationGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.7 | A collection of notification about system hard disk. | ||
| hwPatchLoadGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.8 | Description. | ||
| hwPatchTrapsGrop | 1.3.6.1.4.1.2011.5.25.19.3.2.9 | Patch operation error. | ||
| hwPatchInfoGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.10 | Description. | ||
| hwPatchFileGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.11 | Description. | ||
| hwSysPafFileGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.13 | Description. | ||
| hwSysPafLicenseGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.14 | Description. | ||
| hwSysRebootAndSwitchGrop | 1.3.6.1.4.1.2011.5.25.19.3.2.15 | Description. | ||
| hwBootRomGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.16 | Description. | ||
| hwSystemCfcardNotificationGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.17 | A collection of notification about system cfcard. | ||
| hwSysUpgradeGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.18 | A collection of system upgrade. | ||
| hwSysRebootInfoGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.19 | A collection of system upgrade. | ||
| hwSysDeviceCheckGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.20 | A collection of system device checks. | ||
| huaweiSysVoiceFileGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.21 | A collection of objects providing mandatory system configureation file information. | ||
| hwSysWlanApUpgradeCmdGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.22 | A collection of system wlan ap upgrade. | ||
| hwSysWlanApUpgradeStatusGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.23 | A collection of system wlan ap upgrade status. | ||
| hwSysWlanApUpgradeNotificationsGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.24 | A collection of system wlan ap upgrade notifications. | ||
| huaweiSysAndroidFileGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.25 | A collection of objects providing mandatory system android file information. | ||
| huaweihwSysEvmTrapsObjectGroup | 1.3.6.1.4.1.2011.5.25.19.3.2.26 | A collection of objects providing EVM system trap objects. |
RFC description
Huawei system management MIB controlling device configuration, image files, reload actions, and notifications.
Start monitoring Huawei Datacom switch/router, VRP-based platform (system/config/patch management) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.