All MIBs › HUAWEI-ETHOAM-MIB
Organization: Huawei Technologies Co.,Ltd.
Last Updated: 2015-04-24
Category: Technology: OAM, Vendor: Huawei
Description: Huawei Ethernet OAM MIB for managing IEEE 802.3ah and IEEE 802.1ag OAM functions including link monitoring, remote loopback, and fault notification.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-ETHOAM-MIB?
HUAWEI-ETHOAM-MIB is a Huawei Technologies proprietary MIB implementing IEEE 802.1ag Connectivity Fault Management (CFM) Ethernet OAM. Its objects cover a global CFM enable flag and version, a Maintenance Domain (MD) table (format, name, level, MHF creation/ID-permission behavior, format name, row status) and a Maintenance Association (MA) table (name, VLAN/VSI/L2VC mapping type and value, packet priority, and CCM interval). As a configuration/protocol-status MIB it lets an administrator confirm CFM maintenance domains and associations are correctly scoped to the intended VLAN or pseudowire before relying on it for carrier Ethernet fault detection. It is deployed on Huawei carrier Ethernet switches/routers. Engineers can download the HUAWEI-ETHOAM-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-ETHOAM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei carrier Ethernet switches/routers
Monitoring Examples
An administrator checks hwDot1agCfmMaMapVlanValue and hwDot1agCfmMaCcmInterval to confirm a CFM maintenance association is monitoring the correct VLAN at the expected heartbeat interval on a Huawei switch.
What Can Be Monitored
- CFM maintenance domain/association configuration
This MIB depends on
Related MIBs
Imported Objects
From HCNUM-TC
| CounterBasedGauge64 |
From HUAWEI-MIB
| hwDatacomm | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero | |
| ifDescr | OBJECT-TYPE |
| ifIndex | OBJECT-TYPE |
From P-BRIDGE-MIB
| EnabledStatus |
From Q-BRIDGE-MIB
| VlanIdOrNone |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| BITS | |
| Counter32 | |
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| MacAddress | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeInterval | |
| TimeStamp | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hwEthOam | 1.3.6.1.4.1.2011.5.25.136 | |||
| hwEthOamMib | 1.3.6.1.4.1.2011.5.25.136.1 | Ethernet OAM MIB | ||
| hwEthOam1ag | 1.3.6.1.4.1.2011.5.25.136.1.1 | |||
| ENA hwDot1agCfmEnabled | 1.3.6.1.4.1.2011.5.25.136.1.1.1 | EnabledStatus | read-write | This object indicates whether CFM is enabled globally. The value of this object can be: Enabled: indicates that CFM is enabled globally. Disabled: indicates that global CFM is disabled |
| INT hwDot1agCfmVersion | 1.3.6.1.4.1.2011.5.25.136.1.1.2 | INTEGER | read-write | This object indicates the supported CFM version. The value of this object can be: draft: indicates IEEE 802.1ag Draft 7. standard: indicates IEEE Standard 802.1ag-2007. |
| hwDot1agCfmMdObject | 1.3.6.1.4.1.2011.5.25.136.1.1.3 | |||
| U32 hwDot1agCfmMdTableNextIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.3.1 | Unsigned32 | read-only | The index to the Maintenance Domain table. hwDot1agCfmMdTableNextIndex needs to be inspected to find an available index for row-creation. |
| hwDot1agCfmMdTable | 1.3.6.1.4.1.2011.5.25.136.1.1.3.2 | not-accessible | This table is used to create a Maintenance Domain (MD). A Maintenance Domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance. | |
| hwDot1agCfmMdEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.3.2.1 | not-accessible | The Maintenance Domain table entry. This entry is not lost upon reboot. It is backed up by stable storage. | |
| U32 hwDot1agCfmMdIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.3.2.1.1 | Unsigned32 | not-accessible | This object indicates the index of the MD Table. hwDot1agCfmMdTableNextIndex needs to be inspected to find an available index for row-creation. |
| INT hwDot1agCfmMdFormat | 1.3.6.1.4.1.2011.5.25.136.1.1.3.2.1.2 | INTEGER | read-create | This object indicates the format of the MD name. By default, the value is string. |
| OCT hwDot1agCfmMdName | 1.3.6.1.4.1.2011.5.25.136.1.1.3.2.1.3 | OCTET STRING | read-create | This object indicates the name of the MD. The type/format of this object is determined by the value of the hwDot1agCfmMdFormat object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain. |
| HWD hwDot1agCfmMdMdLevel | 1.3.6.1.4.1.2011.5.25.136.1.1.3.2.1.4 | HWDot1agCfmMDLevel | read-create | This object indicates the level of the MD. The value ranges from 0 to 7. The greater the value, the higher the preference. By default, the value is 0. |
| INT hwDot1agCfmMdMhfCreation | 1.3.6.1.4.1.2011.5.25.136.1.1.3.2.1.5 | INTEGER | read-create | This object indicates whether the management entity can create MIPs for the MD. The value of this object can be: defMHFnone: indicates that the MIPs are not automatically created. defMHFdefault: indicates that the management entity automatically creates MIPs based on certain rules. defMHFexplicit: indicates that the management entity automatically creates MIPs based on certain rules. By default, the value is defMHFnone. |
| INT hwDot1agCfmMdMhfIdPermission | 1.3.6.1.4.1.2011.5.25.136.1.1.3.2.1.6 | INTEGER | read-create | This object indicates what is to be included in the Sender ID TLV transmitted by MPs configured in the MD. The value of this object can be: sendIdNone: indicates that the Sender ID TLV is not to be sent. sendIdChassis: indicates that the Sender ID TLV to be sent contains the chassis ID information. sendIdManage: indicates that the Sender ID TLV to be sent contains management address information. sendIdChassisManage: indicates that the Sender ID TLV to be sent contains both chassis ID information and management address information. sendIdDefer: indicates that the contents of the Sender ID TLV to be sent are determined by the MD management entity. By default, the value is sendIdDefer. |
| OCT hwDot1agCfmMdFormatName | 1.3.6.1.4.1.2011.5.25.136.1.1.3.2.1.7 | OCTET STRING | read-create | This object indicates the MD format name. The type/format of this object is determined by the value of the hwDot1agCfmMdFormatName object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain. |
| ROW hwDot1agCfmMdRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.1.3.2.1.99 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwDot1agCfmMaObject | 1.3.6.1.4.1.2011.5.25.136.1.1.4 | |||
| U32 hwDot1agCfmMaNextIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.4.1 | Unsigned32 | read-only | Value to be used as the index of the MA table entries. |
| hwDot1agCfmMaTable | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2 | not-accessible | This table is used to create a Maintenance Association (MA). Each row in the table represents an MA. An MA is a set of MEPs, each configured with a single service instance. | |
| hwDot1agCfmMaEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1 | not-accessible | The MA table entry. | |
| U32 hwDot1agCfmMaIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.1 | Unsigned32 | not-accessible | This object indicates the index of the MA table. |
| OCT hwDot1agCfmMaName | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.2 | OCTET STRING | read-create | This object indicates the name of the MA. This name MUST be unique within a maintenance domain. |
| INT hwDot1agCfmMaMapType | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.3 | INTEGER | read-create | This object indicates what is associated with the MA. The value of this object can be: mapVlan: indicates that a VLAN is associated with the current MA. mapVsi: indicates that a VSI is associated with the current MA. mapL2vc: indicates that an L2VC is associated with the current MA. unbind: indicates that the MA is not associated with any service instance. mapCcc: indicates that a CCC is associated with the current MA. By default, the value is unbind. |
| VLA hwDot1agCfmMaMapVlanValue | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.4 | VlanIdOrNone | read-create | This object indicates the ID of the VLAN associated with the MA. |
| OCT hwDot1agCfmMaMapVsiName | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.5 | OCTET STRING | read-create | This object indicates the name of the VSI associated with the MA. |
| U32 hwDot1agCfmMaMapL2vcValue | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.6 | Unsigned32 | read-create | This object indicates the ID of the L2VC associated with the MA. |
| INT hwDot1agCfmMaMapL2vcType | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.7 | INTEGER | read-create | This object indicates the encapsulation type of the L2VC associated with the MA. The value of this object can be: invalid: indicates that no display shows that the L2VC is associated with the current MA. l2vcRaw: indicates that the VLAN tag is not encapsulated into the packet. l2vcTagged: indicates that the VLAN tag is encapsulated into the packet. By default, the value is invalid. |
| I32 hwDot1agCfmMaPktPriority | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.8 | Integer32 | read-create | This object indicates the priority of the 802.1ag packet sent in the MA. The value ranges from 0 to 7. The greater the value is, the higher the priority is. By default, the value is 7. |
| INT hwDot1agCfmMaCcmInterval | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.9 | INTEGER | read-create | This object indicates the interval for an MEP in the MA to send or probe CCMs. The value of this object can be: 3.3 milliseconds 10 milliseconds 20 milliseconds 30 milliseconds 50 milliseconds 100 milliseconds 1 second 10 seconds 1 minute 10 minutes By default, the value is 1 second. |
| I32 hwDot1agCfmMaRmepActiveTime | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.10 | Integer32 | read-create | This object indicates the time period after which RMEP configurations are to be activated. The value ranges from 0 to 600 in seconds. By default, the value is 0. |
| I32 hwDot1agCfmMaMepFngAlarmTime | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.11 | Integer32 | read-create | This object indicates the delay for the RMEP to send trap messages. The value must be an integer multiple of 500, for example, 500, 1000, or 1500. The value ranges from 0 to 30000 in milliseconds. By default, the value is 2500. |
| I32 hwDot1agCfmMaMepFngResetTime | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.12 | Integer32 | read-create | This object indicates the delay for the RMEP to send alarm clearance messages after the fault is rectified. The value must be an integer multiple of 500, for example, 500, 1000, or 1500. The value ranges from 0 to 30000 in milliseconds. By default, the value is 10000. |
| INT hwDot1agCfmMaFormat | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.13 | INTEGER | read-create | This object indicates the format of the MA name. string: indicates that the format of the MA name is string. icc-based: indicates that the format of the MA name is ICC-based. By default, the value is string. |
| OCT hwDot1agCfmMaFormatName | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.14 | OCTET STRING | read-create | This object indicates the MA format name. The type/format of this object is determined by the value of the hwDot1agCfmMaFormatName object. |
| OCT hwDot1agCfmMaMapCccName | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.15 | OCTET STRING | read-create | This object indicates the name of the CCC associated with the MA. |
| ROW hwDot1agCfmMaRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.1.4.2.1.99 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwDot1agCfmMepObject | 1.3.6.1.4.1.2011.5.25.136.1.1.5 | |||
| hwDot1agCfmMepTable | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1 | not-accessible | This table is used to create a Maintenance Association End Point (MEP). | |
| hwDot1agCfmMepEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1 | not-accessible | The MEP table entry. | |
| I32 hwDot1agCfmMepIdentifier | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1.1 | Integer32 | accessible-for-notify | This object indicates the ID of the MEP. Integer that is unique among all the MEPs in the same MA. MEP Identifier is also known as the MEPID. The value ranges from 1 to 8191. |
| T/F hwDot1agCfmMepIsVlanType | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1.2 | TruthValue | read-create | This object indicates whether the MEP in the MA is a VLAN-based MEP. If the MEP is a VLAN-based MEP, the MA must have been associated with a VLAN and the interface and VLAN information need not be configured. If the MEP is not a VLAN-based MEP, entry creation fails. |
| NUM hwDot1agCfmMepIfIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1.3 | InterfaceIndexOrZero | read-create | This object indicates the interface to which the MEP is bound. The interface is either a bridge port, or an aggregated IEEE 802.1 link within a bridge port, to which the MEP is attached. By default, the value of IfIndex is 0. |
| VLA hwDot1agCfmMepDot1qVlan | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1.4 | VlanIdOrNone | read-create | This object indicates the VLAN to which the interface that the MEP is bound to belong. |
| VLA hwDot1agCfmMepPeVlan | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1.5 | VlanIdOrNone | read-create | This object indicates the QinQ PE VLAN bound to the MEP. |
| VLA hwDot1agCfmMepCeVlan | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1.6 | VlanIdOrNone | read-create | This object indicates the QinQ CE VLAN bound to the MEP. |
| INT hwDot1agCfmMepDirection | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1.7 | INTEGER | read-create | This object indicates the direction in which the MEP sends the 802.1ag protocol packets. The value of this object can be: invalid: indicates the invalid value. dirInward: indicates that the 802.1ag protocol packets sent by an inward-facing MEP are transmitted through all the interfaces in the VLAN associated with the current MA (except the interface where the MEP resides). That is, an inward-facing MEP broadcasts the 802.1ag protocol packets in the VLAN associated with the current MA. dirOutward: indicates that the 802.1ag protocol packets sent by an outward-facing MEP are transmitted directly through the interface on which the MEP resides. By default, the value is invalid. |
| ENA hwDot1agCfmMepCcmSendEnabled | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1.8 | EnabledStatus | read-create | This object indicates whether CCM sending is enabled on the MEP in an MA. The value of this object can be: enabled disabled By default, the value is disabled. |
| MAC hwDot1agCfmMepMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1.9 | MacAddress | read-only | This object indicates the MAC address of an MEP. |
| ROW hwDot1agCfmMepRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.1.5.1.1.99 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwDot1agCfmRMepObject | 1.3.6.1.4.1.2011.5.25.136.1.1.6 | |||
| hwDot1agCfmRMepTable | 1.3.6.1.4.1.2011.5.25.136.1.1.6.1 | not-accessible | This table is used to create a Remote Maintenance Association End Point (RMEP). | |
| hwDot1agCfmRMepEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.6.1.1 | not-accessible | The remote MEP table entity. | |
| I32 hwDot1agCfmRMepIdentifier | 1.3.6.1.4.1.2011.5.25.136.1.1.6.1.1.1 | Integer32 | accessible-for-notify | This object indicates the ID of the RMEP. The value ranges from 1 to 8191. |
| MAC hwDot1agCfmRMepMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.1.6.1.1.2 | MacAddress | read-create | This object indicates the MAC address of the interface the RMEP resides. |
| ENA hwDot1agCfmRMepCcmRecvEnabled | 1.3.6.1.4.1.2011.5.25.136.1.1.6.1.1.3 | EnabledStatus | read-create | This object indicates whether CCM receiving is enabled on the current device. The value can be: enabled disabled By default, the value is disabled. |
| INT hwDot1agCfmRMepStateIsUp | 1.3.6.1.4.1.2011.5.25.136.1.1.6.1.1.4 | INTEGER | read-only | This object indicates the CFM status. The value can be: up: indicates that the CFM status is Up. down: indicates that the CFM status is Down. invalid: indicates that the CFM status is not enabled. |
| HWD hwDot1agCfmRMepHighestPrDefect | 1.3.6.1.4.1.2011.5.25.136.1.1.6.1.1.5 | HWDot1agCfmHighestDefectPri | read-only | This object indicates the severity level of the fault on an RMEP. If the CFM status is Up, this object is displayed as none. |
| ROW hwDot1agCfmRMepRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.1.6.1.1.99 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwDot1agCfmMipObject | 1.3.6.1.4.1.2011.5.25.136.1.1.7 | |||
| hwDot1agCfmMipTable | 1.3.6.1.4.1.2011.5.25.136.1.1.7.1 | not-accessible | This table is used to display information about a Maintenance Association Intermediate Point (MIP). | |
| hwDot1agCfmMipEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.7.1.1 | not-accessible | The MIP table entry. | |
| NUM hwDot1agCfmMipIfIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.7.1.1.1 | InterfaceIndex | not-accessible | This object indicates the interface on which the MIP resides. |
| HWD hwDot1agCfmMipLevel | 1.3.6.1.4.1.2011.5.25.136.1.1.7.1.1.2 | HWDot1agCfmMDLevel | read-only | This object indicates the level of the MIP. The value ranges from 0 to 7. |
| MAC hwDot1agCfmMipIfMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.1.7.1.1.3 | MacAddress | read-only | This object indicates the MAC address of the interface on which the MIP resides. |
| hwDot1agCfmMacPingObject | 1.3.6.1.4.1.2011.5.25.136.1.1.8 | |||
| hwDot1agCfmMacPingTable | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1 | not-accessible | The entries related to the Mac Ping include the parameters input by users and the returned results. | |
| hwDot1agCfmMacPingEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1 | not-accessible | This table is used to configure the MAC ping function. | |
| U32 hwDot1agCfmMacPingIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.1 | Unsigned32 | not-accessible | This object indicates the index of this table. |
| ENA hwDot1agCfmMacPingState | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.2 | EnabledStatus | read-create | This object indicates whether the MAC ping function is enabled. The value can be: enabled disabled By default, the value is disabled. |
| OCT hwDot1agCfmMacPingMdName | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.3 | OCTET STRING | read-create | This object indicates the name of the MD where MAC ping is performed. |
| OCT hwDot1agCfmMacPingMaName | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.4 | OCTET STRING | read-create | This object indicates the name of the MA where MAC ping is performed. |
| I32 hwDot1agCfmMacPingMepId | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.5 | Integer32 | read-create | This object indicates the ID of the local MEP of the 802.1ag MAC ping operation. The value ranges from 1 to 8191. By default, the value is 0. |
| T/F hwDot1agCfmMacPingDestIsMepId | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.6 | TruthValue | read-create | This object indicates whether the destination MAC address of the LBM is the MAC address of the interface on which the RMEP resides. |
| I32 hwDot1agCfmMacPingDestMepId | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.7 | Integer32 | read-create | This object indicates the ID of the destination RMEP of the 802.1ag MAC ping operation. The value ranges from 1 to 8191. By default, the value is 0. |
| MAC hwDot1agCfmMacPingMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.8 | MacAddress | read-create | This object indicates the destination MAC address of the LBM. |
| NUM hwDot1agCfmMacPingOutIfIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.9 | InterfaceIndexOrZero | read-create | This object indicates the outbound interface that sends the LBM. |
| U32 hwDot1agCfmMacPingTimeOut | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.10 | Unsigned32 | read-create | This object indicates the timeout period for waiting for the LBR. The value ranges from 1 to 65535 in milliseconds. By default, the value is 2000. |
| U32 hwDot1agCfmMacPingCount | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.11 | Unsigned32 | read-create | This object indicates the number of ping operation times. The value ranges from 1 to 4294967295. By default, the value is 5. |
| I32 hwDot1agCfmMacPingPacketSize | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.12 | Integer32 | read-create | This object indicates the length of the LBM. The value ranges from 64 to 9500. By default, the value is 95. |
| I32 hwDot1agCfmMacPingPriority | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.13 | Integer32 | read-create | This object indicates the priority of the sent LBM packet. The value ranges from 0 to 7 or can be 255. The value 255 is an invalid value. If the value is set to 255, this value should be identical with the priority value of the MA which the MEP belongs to. The greater the value is, the higher the priority is. |
| C32 hwDot1agCfmMacPingSendPacketNum | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.14 | Counter32 | read-only | This object indicates the number of sent LBMs. |
| C32 hwDot1agCfmMacPingRecvPacketNum | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.15 | Counter32 | read-only | This object indicates the number of received LBRs. |
| U32 hwDot1agCfmMacPingPacketLossRatio | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.16 | Unsigned32 | read-only | This object indicates the frame loss ratio on the physical link. The value ranges from 0 to 100. |
| U32 hwDot1agCfmMacPingRecvTimeDelayMin | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.17 | Unsigned32 | read-only | This object indicates the minimum delay in receiving the LBM. |
| U32 hwDot1agCfmMacPingRecvTimeDelayMax | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.18 | Unsigned32 | read-only | This object indicates the maximum delay in receiving the LBM. |
| U32 hwDot1agCfmMacPingRecvTimeDelayAvg | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.19 | Unsigned32 | read-only | This object indicates the average delay in receiving the LBM. |
| ROW hwDot1agCfmMacPingRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.1.8.1.1.99 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwDot1agCfmMacTraceObjects | 1.3.6.1.4.1.2011.5.25.136.1.1.9 | |||
| hwDot1agCfmMacTraceTable | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1 | not-accessible | This table is used to configure the MAC trace function. | |
| hwDot1agCfmMacTraceEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1 | not-accessible | Indicates the MAC Trace table entry. | |
| U32 hwDot1agCfmMacTraceIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.1 | Unsigned32 | not-accessible | This object indicates the index of this table. |
| ENA hwDot1agCfmMacTraceState | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.2 | EnabledStatus | read-create | This object indicates whether the MAC trace function is enabled. The value can be: enabled disabled By default, the value is disabled. |
| OCT hwDot1agCfmMacTraceMdName | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.3 | OCTET STRING | read-create | This object indicates the name of the MD where MAC trace is performed. |
| OCT hwDot1agCfmMacTraceMaName | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.4 | OCTET STRING | read-create | This object indicates the name of the MA where MAC trace is performed. |
| I32 hwDot1agCfmMacTraceMepId | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.5 | Integer32 | read-create | This object indicates the ID of the local MEP of the 802.1ag MAC trace operation. The value ranges from 1 to 8191. By default, the value is 0. |
| T/F hwDot1agCfmMacTraceDestIsMepId | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.6 | TruthValue | read-create | This object indicates whether the destination MAC address of the LTM is the MAC address of the interface on which the RMEP resides. |
| I32 hwDot1agCfmMacTraceDestMepId | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.7 | Integer32 | read-create | This object indicates the ID of the destination RMEP of the 802.1ag MAC trace operation. The value ranges from 1 to 8191. By default, the value is 0. |
| MAC hwDot1agCfmMacTraceMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.8 | MacAddress | read-create | This object indicates the destination MAC address of the LTM. |
| NUM hwDot1agCfmMacTraceOutIfIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.9 | InterfaceIndexOrZero | read-create | This object indicates the outbound interface that sends the LTM. |
| U32 hwDot1agCfmMacTraceTimeOut | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.10 | Unsigned32 | read-create | This object indicates the timeout period for waiting for the LTR. The value ranges from 1 to 65535, in milliseconds. By default, the value is 2000. |
| U32 hwDot1agCfmMacTraceTTL | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.11 | Unsigned32 | read-create | This object indicates the TTL value of the 802.1ag MAC trace operation. The value ranges from 1 to 255. By default, the value is 64. |
| U32 hwDot1agCfmMacTraceSendSeqNumber | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.12 | Unsigned32 | read-only | This object indicates the sequence number of the sent LTR. |
| INT hwDot1agCfmMacTraceResult | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.13 | INTEGER | read-only | This object indicates the result of the MAC trace operation. |
| ROW hwDot1agCfmMacTraceRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.1.9.1.1.99 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwDot1agCfmMacTraceReplyTable | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2 | not-accessible | This table is used to display information about the LTR for responding to the MAC trace operation. | |
| hwDot1agCfmMacTraceReplyEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1 | not-accessible | The Mac Trace result table entry. | |
| U32 hwDot1agCfmMacTraceReplySeqNumber | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.1 | Unsigned32 | not-accessible | This object indicates the index of this table. The value is the sequence number of the LTR. |
| U32 hwDot1agCfmMacTraceReplyRecvOrder | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.2 | Unsigned32 | not-accessible | This object indicates the index of this table. The value is the sequence in which the MAC trace results are displayed. |
| U32 hwDot1agCfmMacTraceReplyTTL | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.3 | Unsigned32 | read-only | This object indicates the TTL of the LTR. The value ranges from 0 to 255. |
| T/F hwDot1agCfmMacTraceReplyForwarded | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.4 | TruthValue | read-only | This object indicates whether the device that sends the LTR keeps on forwarding LTMs. |
| T/F hwDot1agCfmMacTraceReplyTerminalMep | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.5 | TruthValue | read-only | This object indicates whether the LTR is sent by an MEP. |
| HWD hwDot1agCfmMacTraceReplyRelayAction | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.6 | HWDot1agCfmRelayActionFieldValue | read-only | This object indicates the value of the Relay Action field in the LTR. |
| HWD hwDot1agCfmMacTraceReplyIngressAction | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.7 | HWDot1agCfmIngressActionFieldValue | read-only | This object indicates the value of the Ingress Action field in the LTR. |
| MAC hwDot1agCfmMacTraceReplyIngressMac | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.8 | MacAddress | read-only | This object indicates the physical MAC address carried in the ingress MAC address field in the LTR. |
| OCT hwDot1agCfmMacTraceReplyIngressIfName | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.9 | OCTET STRING | read-only | This object indicates the name of the inbound interface of the LTR. |
| HWD hwDot1agCfmMacTraceReplyEgressAction | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.10 | HWDot1agCfmEgressActionFieldValue | read-only | This object indicates the value of the Egress Action field in the LTR. |
| MAC hwDot1agCfmMacTraceReplyEgressMac | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.11 | MacAddress | read-only | This object indicates the physical MAC address carried in the egress MAC address field in the LTR. |
| OCT hwDot1agCfmMacTraceReplyEgressIfName | 1.3.6.1.4.1.2011.5.25.136.1.1.9.2.1.12 | OCTET STRING | read-only | This object indicates the name of the interface that forwards the LTR. |
| hwDot1agCfmQueryObject | 1.3.6.1.4.1.2011.5.25.136.1.1.10 | |||
| hwDot1agCfmQueryMdIndexTable | 1.3.6.1.4.1.2011.5.25.136.1.1.10.1 | not-accessible | This table is used to get the index of the Maintenance Domain table. | |
| hwDot1agCfmQueryMdIndexEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.10.1.1 | not-accessible | The Md Index table entry. | |
| OCT hwDot1agCfmQueryMdName | 1.3.6.1.4.1.2011.5.25.136.1.1.10.1.1.1 | OCTET STRING | not-accessible | This object indicates the name of the Maintenance Domain. |
| U32 hwDot1agCfmQueryMdIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.10.1.1.2 | Unsigned32 | read-only | This object indicates the index to the Maintenance Domain table. |
| hwDot1agCfmQueryMaIndexTable | 1.3.6.1.4.1.2011.5.25.136.1.1.10.2 | not-accessible | This table is used to get the index of the Maintenance Association table. | |
| hwDot1agCfmQueryMaIndexEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.10.2.1 | not-accessible | The Ma Index table entry. | |
| OCT hwDot1agCfmQueryMaName | 1.3.6.1.4.1.2011.5.25.136.1.1.10.2.1.1 | OCTET STRING | not-accessible | This object indicates the name of Maintenance Association. |
| U32 hwDot1agCfmQueryMaIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.10.2.1.2 | Unsigned32 | read-only | This object indicates the index to the Maintenance Association table. |
| hwDot1agCfmGmacTraceObjects | 1.3.6.1.4.1.2011.5.25.136.1.1.11 | |||
| ENA hwDot1agCfmGmacTraceEnabled | 1.3.6.1.4.1.2011.5.25.136.1.1.11.1 | EnabledStatus | read-write | This object indicates whether GMAC trace function is enabled globally. The value of this object can be: Enabled: indicates that GMAC trace function is enabled globally. Disabled: indicates that GMAC trace function is disabled globally. |
| hwDot1agCfmGmacTraceTable | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2 | not-accessible | This table is used to configure the GMAC trace function. | |
| hwDot1agCfmGmacTraceEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1 | not-accessible | Indicates the GMAC Trace table entry. | |
| U32 hwDot1agCfmGmacTraceIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.1 | Unsigned32 | not-accessible | This object indicates the index of this table. |
| ENA hwDot1agCfmGmacTraceState | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.2 | EnabledStatus | read-create | This object indicates whether the GMAC trace function is enabled. The value can be: enabled disabled By default, the value is disabled. |
| MAC hwDot1agCfmGmacTraceMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.3 | MacAddress | read-create | This object indicates the destination MAC address of the LTM. |
| INT hwDot1agCfmGmacTraceServiceType | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.4 | INTEGER | read-create | This object indicates the service type associated with the gmac trace. The value of this object can be: vlan: indicates that a VLAN is associated with the gmac trace. invalid: indicates that no service type is specified for the gmac trace. By default, the value is invalid. |
| VLA hwDot1agCfmGmacTraceVlanValue | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.5 | VlanIdOrNone | read-create | This object indicates the VLAN to the destination MAC address. |
| OCT hwDot1agCfmGmacTraceVsiName | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.6 | OCTET STRING | read-create | This object indicates the name of the VSI associated with the GMAC trace. |
| U32 hwDot1agCfmGmacTraceL2vcValue | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.7 | Unsigned32 | read-create | This object indicates the ID of the L2VC associated with the GMAC trace. |
| INT hwDot1agCfmGmacTraceL2vcType | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.8 | INTEGER | read-create | This object indicates the encapsulation type of the L2VC associated with the gmac trace. The value of this object can be: invalid: indicates that no display shows that the L2VC is associated with the current gmac trace. l2vcRaw: indicates that the VLAN tag is not encapsulated into the packet. l2vcTagged: indicates that the VLAN tag is encapsulated into the packet. By default, the value is invalid. |
| VLA hwDot1agCfmGmacTraceDot1qVlan | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.9 | VlanIdOrNone | read-create | This object indicates the DOT1Q VLAN ID to the destination MAC address. |
| VLA hwDot1agCfmGmacTracePeVlan | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.10 | VlanIdOrNone | read-create | This object indicates the QinQ PE VLAN bound to the GMAC trace. |
| VLA hwDot1agCfmGmacTraceCeVlan | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.11 | VlanIdOrNone | read-create | This object indicates the QinQ CE VLAN bound to the GMAC trace. |
| NUM hwDot1agCfmGmacTraceOutIfIndex | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.12 | InterfaceIndexOrZero | read-create | This object indicates the outbound interface that sends the LTM. |
| U32 hwDot1agCfmGmacTraceTimeOut | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.13 | Unsigned32 | read-create | This object indicates the timeout period for waiting for the LTR. The value ranges from 1 to 65535, in milliseconds. By default, the value is 2000. |
| T/F hwDot1agCfmGmacTraceDisplayHostInfo | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.14 | TruthValue | read-create | This object indicates whether the LTR include host information. |
| U32 hwDot1agCfmGmacTraceSendSeqNumber | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.15 | Unsigned32 | read-only | This object indicates the sequence number of the sent LTR. |
| INT hwDot1agCfmGmacTraceResult | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.16 | INTEGER | read-only | This object indicates the result of the GMAC trace operation. |
| ROW hwDot1agCfmGmacTraceRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.1.11.2.1.99 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwDot1agCfmGmacTraceReplyTable | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3 | not-accessible | This table is used to display information about the LTR for responding to the GMAC trace operation. | |
| hwDot1agCfmGmacTraceReplyEntry | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1 | not-accessible | The GMAC Trace result table entry. | |
| U32 hwDot1agCfmGmacTraceReplySeqNumber | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.1 | Unsigned32 | not-accessible | This object indicates the index of this table. The value is the sequence number of the LTR. |
| U32 hwDot1agCfmGmacTraceReplyRecvOrder | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.2 | Unsigned32 | not-accessible | This object indicates the index of this table. The value is the sequence in which the GMAC trace results are displayed. |
| U32 hwDot1agCfmGmacTraceReplyTTL | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.3 | Unsigned32 | read-only | This object indicates the TTL of the LTR. The value ranges from 0 to 255. |
| T/F hwDot1agCfmGmacTraceReplyForwarded | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.4 | TruthValue | read-only | This object indicates whether the device that sends the LTR keeps on forwarding LTMs. |
| OCT hwDot1agCfmGmacTraceReplyHostInfo | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.5 | OCTET STRING | read-only | This object indicates the host name and IP address of each hop. |
| HWD hwDot1agCfmGmacTraceReplyRelayAction | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.6 | HWDot1agCfmRelayActionFieldValue | read-only | This object indicates the value of the Relay Action field in the LTR. |
| HWD hwDot1agCfmGmacTraceReplyIngressAction | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.7 | HWDot1agCfmIngressActionFieldValue | read-only | This object indicates the value of the Ingress Action field in the LTR. |
| MAC hwDot1agCfmGmacTraceReplyIngressMac | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.8 | MacAddress | read-only | This object indicates the physical MAC address carried in the ingress MAC address field in the LTR. |
| OCT hwDot1agCfmGmacTraceReplyIngressIfName | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.9 | OCTET STRING | read-only | This object indicates the name of the inbound interface of the LTR. |
| HWD hwDot1agCfmGmacTraceReplyEgressAction | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.10 | HWDot1agCfmEgressActionFieldValue | read-only | This object indicates the value of the Egress Action field in the LTR. |
| MAC hwDot1agCfmGmacTraceReplyEgressMac | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.11 | MacAddress | read-only | This object indicates the physical MAC address carried in the egress MAC address field in the LTR. |
| OCT hwDot1agCfmGmacTraceReplyEgressIfName | 1.3.6.1.4.1.2011.5.25.136.1.1.11.3.1.12 | OCTET STRING | read-only | This object indicates the name of the interface that forwards the LTR. |
| INT hwDot1agCfmMPAddressModel | 1.3.6.1.4.1.2011.5.25.136.1.1.101 | INTEGER | read-write | This object indicates the MP address model of the CFM. The value of this object can be: bridge: indicates bridge MAC MP address model. individual: indicates individual MP address model. |
| hwEthOam3ah | 1.3.6.1.4.1.2011.5.25.136.1.2 | |||
| ENA hwDot3ahEfmEnabled | 1.3.6.1.4.1.2011.5.25.136.1.2.1 | EnabledStatus | read-write | Enable the EFM globally. |
| hwDot3ahEfmObject | 1.3.6.1.4.1.2011.5.25.136.1.2.2 | |||
| hwDot3ahEfmDetectModeTable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.1 | not-accessible | Set the detection mode table in the last one kilometer on the interface. | |
| hwDot3ahEfmDetectModeEntry | 1.3.6.1.4.1.2011.5.25.136.1.2.2.1.1 | not-accessible | Set the detection mode entity in the last one kilometer on the interface. | |
| HWD hwDot3ahEfmDetectMode | 1.3.6.1.4.1.2011.5.25.136.1.2.2.1.1.11 | HWDetectType | read-write | Detection mode ( fast detection and standard detection) |
| NUM hwDot3ahEfmDetectInterval | 1.3.6.1.4.1.2011.5.25.136.1.2.2.1.1.12 | TimeInterval | read-write | Time interval of detection |
| I32 hwDot3ahEfmDetectMalfunction | 1.3.6.1.4.1.2011.5.25.136.1.2.2.1.1.13 | Integer32 | read-only | Failure description from 802.3ah and from associated modules. |
| hwDot3ahEfmTable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.2 | not-accessible | This table contains the primary controls and status for the OAM capabilities of an Ethernet like interface. There will be one row in this table for each Ethernet like interface in the system that supports the OAM functions defined in [802.3ah]. | |
| hwDot3ahEfmEntry | 1.3.6.1.4.1.2011.5.25.136.1.2.2.2.1 | not-accessible | An entry in the table, containing information on the Ethernet OAM function for a single Ethernet like interface. Entries in the table are created automatically for each interface supporting Ethernet OAM. The status of the row entry can be determined from hwDot3ahEfmOperStatus. A hwDot3ahEfmEntry is indexed in the hwDot3ahEfmTable by the ifIndex object of the Interfaces MIB. | |
| ENA hwDot3ahEfmAdminState | 1.3.6.1.4.1.2011.5.25.136.1.2.2.2.1.1 | EnabledStatus | read-write | This object is used to provision the default administrative OAM mode for this interface. This object represents the desired state of OAM for this interface. The hwDot3ahEfmAdminState always starts in the disabled(2) state until an explicit management action or configuration information retained by the system causes a transition to the enabled(1) state. When enabled(1), Ethernet OAM will attempt to operate over this interface. |
| INT hwDot3ahEfmOperStatus | 1.3.6.1.4.1.2011.5.25.136.1.2.2.2.1.2 | INTEGER | read-only | At initialization and failure conditions, two OAM entities on the same full-duplex Ethernet link begin a discovery phase to determine what OAM capabilities may be used on that link. |
| INT hwDot3ahEfmMode | 1.3.6.1.4.1.2011.5.25.136.1.2.2.2.1.3 | INTEGER | read-write | This object configures the mode of OAM operation for this Ethernet like interface. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode. |
| U32 hwDot3ahEfmMaxOamPduSize | 1.3.6.1.4.1.2011.5.25.136.1.2.2.2.1.4 | Unsigned32 | read-only | The largest OAMPDU that the OAM entity supports. OAM entities exchange maximum OAMPDU sizes and negotiate to use the smaller of the two maximum OAMPDU sizes between the peers. This value is determined by the local implementation. |
| U32 hwDot3ahEfmConfigRevision | 1.3.6.1.4.1.2011.5.25.136.1.2.2.2.1.5 | Unsigned32 | read-only | The configuration revision of the OAM entity as reflected in the latest OAMPDU sent by the OAM entity. The config revision is used by OAM entities to indicate configuration changes have occurred which might require the peer OAM entity to re-evaluate whether OAM peering is allowed. |
| BIT hwDot3ahEfmFunctionsSupported | 1.3.6.1.4.1.2011.5.25.136.1.2.2.2.1.6 | Bits | read-only | The OAM functions supported on this Ethernet like interface. OAM consists of separate functional sets beyond the basic discovery process which is always required. These functional groups can be supported independently by any implementation. These values are communicated to the peer via the local configuration field of Information OAMPDUs. Setting 'unidirectionalSupport(0)' indicates that the OAM entity supports the transmission of OAMPDUs on links that are operating in unidirectional mode (traffic flowing in one direction only). Setting 'loopbackSupport(1)' indicates the OAM entity can initiate and respond to loopback commands. Setting 'eventSupport(2)' indicates the OAM entity can send and receive Event Notification OAMPDUs. Setting 'variableSupport(3)' indicates the OAM entity can send and receive Variable Request and Response OAMPDUs. |
| U32 hwDot3ahEfmTimeout | 1.3.6.1.4.1.2011.5.25.136.1.2.2.2.1.7 | Unsigned32 | read-write | The EFM Timeout object defines the max time that the EFM session stays in detect mode since the last OAMPDU received. if there's no OAMPDU received within the time the timeout value defines, the EFM session will turn into discovery state. The value of EFM Timeout should be three or more times the value of the sending interval of the peer interface. The timeout value must be an exact integral multiple of 100. Range: 300-30000 Default: 5000 Unit: milliseconds |
| U32 hwDot3ahEfmInterval | 1.3.6.1.4.1.2011.5.25.136.1.2.2.2.1.8 | Unsigned32 | read-write | The EFM interval object defines the interval of sending OAM PDUs. The value of EFM interval should be the same as the value of the peer interface. The interval value must be an exact integral multiple of 100. Range: 100-1000 Default: 1000 Unit: milliseconds |
| hwDot3ahEfmPeerTable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.3 | not-accessible | This table contains information about the OAM peer for a particular Ethernet like interface. OAM entities communicate with a single OAM peer entity on Ethernet links on which OAM is enabled and operating properly. There is one entry in this table for each entry in the hwDot3ahEfmTable for which information on the peer OAM entity is available. | |
| hwDot3ahEfmPeerEntry | 1.3.6.1.4.1.2011.5.25.136.1.2.2.3.1 | not-accessible | An entry in the table, containing information on the peer OAM entity for a single Ethernet like interface. Note that there is at most one OAM peer for each Ethernet like interface. Entries are automatically created when information about the OAM peer entity becomes available, and automatically deleted when the OAM peer entity is no longer in communication. Peer information is not available when hwDot3ahEfmOperStatus is disabled(1), linkFault(2), passiveWait(3), activeSendLocal(4). or nonOperHalfDuplex(10)). | |
| OCT hwDot3ahEfmPeerMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.2.2.3.1.1 | OCTET STRING | read-only | The MAC address of the peer OAM entity. The MAC address is derived from the most recently received OAMPDU. |
| HWD hwDot3ahEfmPeerVendorOui | 1.3.6.1.4.1.2011.5.25.136.1.2.2.3.1.2 | HWDot3Oui | read-only | The OUI of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The OUI can be used to identify the vendor of the remote OAM entity. This value is initialized to zero before any Local Information TLV is received. |
| U32 hwDot3ahEfmPeerVendorInfo | 1.3.6.1.4.1.2011.5.25.136.1.2.2.3.1.3 | Unsigned32 | read-only | The Vendor Info of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The vendor information field is within the Local Information TLV, and can be used to determine additional information about the peer entity. The format of the vendor information is unspecified within the 32-bit field. This value is initialized to zero before any Local Information TLV is received. |
| INT hwDot3ahEfmPeerMode | 1.3.6.1.4.1.2011.5.25.136.1.2.2.3.1.4 | INTEGER | read-only | The mode of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The mode of the peer can be determined from the Configuration field in the Local Information TLV of the last Information OAMPDU received from the peer. The value is unknown(3) whenever no Local Information TLV has been received. The values of active(1) and passive(2) are returned when a Local Information TLV has been received indicating the peer is in active or passive mode, respectively. |
| U32 hwDot3ahEfmPeerMaxOamPduSize | 1.3.6.1.4.1.2011.5.25.136.1.2.2.3.1.5 | Unsigned32 | read-only | The maximum size of OAMPDU supported by the peer as reflected in the latest Information OAMPDU received with a Local Information TLV. Ethernet OAM on this interface must not use OAMPDUs that exceed this size. The maximum OAMPDU size can be determined from the PDU Configuration field of the Local Information TLV of the last Information OAMPDU received from the peer. A value of zero is returned if no Local Information TLV has been received. Otherwise, the value of the OAM peer's maximum OAMPDU size is returned in this value. Note that the values 1..65534 are invalid sizes for Ethernet frames and should never appear. |
| U32 hwDot3ahEfmPeerConfigRevision | 1.3.6.1.4.1.2011.5.25.136.1.2.2.3.1.6 | Unsigned32 | read-only | The configuration revision of the OAM peer as reflected in the latest OAMPDU. This attribute is changed by the peer whenever it has a local configuration change for Ethernet OAM this interface. The configuration revision can be determined from the Revision field of the Local Information TLV of the most recently received Information OAMPDU with a Local Information TLV. A value of zero is returned if no Local Information TLV has been received. |
| BIT hwDot3ahEfmPeerFunctionsSupported | 1.3.6.1.4.1.2011.5.25.136.1.2.2.3.1.7 | Bits | read-only | The OAM functions supported on this Ethernet like interface. OAM consists of separate functionality sets above the basic discovery process. This value indicates the capabilities of the peer OAM entity with respect to these functions. This value is initialized so all bits are clear. If unidirectionalSupport(0) is set, then the peer OAM entity supports sending OAM frames on Ethernet interfaces when the receive path is known to be inoperable. If loopbackSupport(1) is set, then the peer OAM entity can send and receive OAM loopback commands. If eventSupport(2) is set, then the peer OAM entity can send and receive event OAMPDUs to signal various error conditions. If variableSupport(3) is set, then the peer OAM entity can send and receive variable requests to monitor attribute value as described in Clause 57 of [802.3ah]. The capabilities of the OAM peer can be determined from the configuration field of the Local Information TLV of the most recently received Information OAMPDU with a Local Information TLV. All zeros are returned if no Local Information TLV has yet been received. |
| hwDot3ahEfmLoopbackTable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.4 | not-accessible | This table contains controls for the loopback state of the local link as well as indicating the status of the loopback function. There is one entry in this table for each entry in hwDot3ahEfmTable that supports loopback functionality (where hwDot3ahEfmFunctionsSupported includes the loopbackSupport bit set). Loopback can be used to place the remote OAM entity in a state where every received frame (except OAMPDUs) is echoed back over the same interface on which they were received. In this state, at the remote entity, 'normal' traffic is disabled as only the looped back frames are transmitted on the interface. Loopback is thus an intrusive operation that prohibits normal data flow and should be used accordingly. | |
| hwDot3ahEfmLoopbackEntry | 1.3.6.1.4.1.2011.5.25.136.1.2.2.4.1 | not-accessible | An entry in the table, containing information on the loopback status for a single Ethernet like interface. Entries in the table are automatically created whenever the local OAM entity supports loopback capabilities. The loopback status on the interface can be determined from the hwDot3ahEfmLoopbackStatus object. | |
| INT hwDot3ahEfmLoopbackStatus | 1.3.6.1.4.1.2011.5.25.136.1.2.2.4.1.1 | INTEGER | read-write | The loopback status of the OAM entity. When operating in normal mode with no loopback in progress, the status reads noLoopback(1). The values initiatingLooopback(2) and terminatingLoopback(4) can be read or written. The other values can only be read - they can never be written. |
| INT hwDot3ahEfmLoopbackIgnoreRx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.4.1.2 | INTEGER | read-write | Since OAM loopback is a disruptive operation (user traffic does not pass), this attribute provides a mechanism to provide controls over whether received OAM loopback commands are processed or ignored. When the value is ignore(1), received loopback commands are ignored. When the value is process(2), OAM loopback commands are processed. The default value is to process loopback commands (process(2)). |
| U32 hwDot3ahEfmLoopbackTimeout | 1.3.6.1.4.1.2011.5.25.136.1.2.2.4.1.3 | Unsigned32 | read-write | This object specifies the timeout period for a remote loopback. The value ranges from 0 to 1000 in minutes. The default value is 20 minutes. 0 indicates that no timeout period is set. |
| hwDot3ahEfmStatsTable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5 | not-accessible | This table contains statistics for the OAM function on a particular Ethernet like interface. There is an entry in the table for every entry in the hwDot3ahEfmTable. The counters in this table are defined as 32-bit entries to match the counter size as defined in [802.3ah]. Given the OAM protocol is a slow protocol, the counters increment at a slow rate. | |
| hwDot3ahEfmStatsEntry | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1 | not-accessible | An entry in the table, containing statistics information on the Ethernet OAM function for a single Ethernet like interface. Entries are automatically created for every entry in the hwDot3ahEfmTable. Counters are maintained across transitions in hwDot3ahEfmOperStatus. | |
| C32 hwDot3ahEfmInformationTx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.1 | Counter32 | read-only | A count of the number of Information OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmInformationRx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.2 | Counter32 | read-only | A count of the number of Information OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmUniqueEventNotificationTx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.3 | Counter32 | read-only | A count of the number of unique Event OAMPDUs transmitted on this interface. Event notifications may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. Duplicate Event Notification transmissions are counted by hwDot3ahEfmDuplicateEventNotificationTx. A unique Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is distinct from the previously transmitted Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmUniqueEventNotificationRx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.4 | Counter32 | read-only | A count of the number of unique Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. Duplicate Event Notification receptions are counted by hwDot3ahEfmDuplicateEventNotificationRx. A unique Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is distinct from the previously received Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmDuplicateEventNotificationTx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.5 | Counter32 | read-only | A count of the number of duplicate Event OAMPDUs transmitted on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously transmitted Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmDuplicateEventNotificationRx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.6 | Counter32 | read-only | A count of the number of duplicate Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously received Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmLoopbackControlTx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.7 | Counter32 | read-only | A count of the number of Loopback Control OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmLoopbackControlRx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.8 | Counter32 | read-only | A count of the number of Loopback Control OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmVariableRequestTx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.9 | Counter32 | read-only | A count of the number of Variable Request OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmVariableRequestRx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.10 | Counter32 | read-only | A count of the number of Variable Request OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmVariableResponseTx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.11 | Counter32 | read-only | A count of the number of Variable Response OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmVariableResponseRx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.12 | Counter32 | read-only | A count of the number of Variable Response OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmOrgSpecificTx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.13 | Counter32 | read-only | A count of the number of Organization Specific OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmOrgSpecificRx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.14 | Counter32 | read-only | A count of the number of Organization Specific OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmUnsupportedCodesTx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.15 | Counter32 | read-only | A count of the number of OAMPDUs transmitted on this interface with an unsupported op-code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmUnsupportedCodesRx | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.16 | Counter32 | read-only | A count of the number of OAMPDUs received on this interface with an unsupported op-code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| C32 hwDot3ahEfmFramesLostDueToOam | 1.3.6.1.4.1.2011.5.25.136.1.2.2.5.1.17 | Counter32 | read-only | A count of the number of frames that were dropped by the OAM multiplexer. Since the OAM multiplexer has multiple inputs and a single output, there may be cases where frames are dropped due to transmit resource contention. This counter is incremented whenever a frame is dropped by the OAM layer. Note that any Ethernet frame, not just OAMPDUs, may be dropped by the OAM layer. This can occur when an OAMPDU takes precedence over a 'normal' frame resulting in the 'normal' frame being dropped. When this counter is incremented, no other counters in this MIB are incremented. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. |
| hwDot3ahEfmEventConfigTable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6 | not-accessible | Ethernet OAM includes the ability to generate and receive Event Notification OAMPDUs to indicate various link problems. This table contains the mechanisms to enable Event Notifications and configure the thresholds to generate the standard Ethernet OAM events. There is one entry in the table for every entry in hwDot3ahEfmTable that supports OAM events (where hwDot3ahEfmFunctionsSupported includes the eventSupport bit set). The values in the table are maintained across changes to hwDot3ahEfmOperStatus. The standard threshold crossing events are: - Errored Symbol Period Event. Generated when the number of symbol errors exceeds a threshold within a given window defined by a number of symbols (for example, 1,000 symbols out of 1,000,000 had errors). - Errored Frame Period Event. Generated when the number of frame errors exceeds a threshold within a given window defined by a number of frames (for example, 10 frames out of 1000 had errors). - Errored Frame Event. Generated when the number of frame errors exceeds a threshold within a given window defined by a period of time (for example, 10 frames in 1 second had errors). - Errored Frame Seconds Summary Event. Generated when the number of errored frame seconds exceeds a threshold within a given time period (for example, 10 errored frame seconds within the last 100 seconds). An errored frame second is defined as a 1 second interval which had >0 frame errors. There are other events (dying gasp, critical events) that are not threshold crossing events but which can be enabled/disabled via this table. | |
| hwDot3ahEfmEventConfigEntry | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1 | not-accessible | Entries are automatically created and deleted from this table, and exist whenever the OAM entity supports Ethernet OAM events (as indicated by the eventSupport bit in hwDot3ahEfmFunctionsSuppported). Values in the table are maintained across changes to the value of hwDot3ahEfmOperStatus. Event configuration controls when the local management entity sends Event Notification OAMPDUs to its OAM peer, and when certain event flags are set or cleared in OAMPDUs. | |
| U32 hwDot3ahEfmErrSymPeriodWindowHi | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.1 | Unsigned32 | read-write | The two objects hwDot3ahEfmErrSymPeriodWindowHi and hwDot3ahEfmErrSymPeriodWindowLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as hwDot3ahEfmErrSymPeriodWindow = ((2^32)*hwDot3ahEfmErrSymPeriodWindowHi) + hwDot3ahEfmErrSymPeriodWindowLo If hwDot3ahEfmErrSymPeriodThreshold symbol errors occur within a window of hwDot3ahEfmErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for hwDot3ahEfmErrSymPeriodWindow is the number of symbols in one second for the underlying physical layer. |
| U32 hwDot3ahEfmErrSymPeriodWindowLo | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.2 | Unsigned32 | read-write | The two objects hwDot3ahEfmErrSymPeriodWindowHi and hwDot3ahEfmErrSymPeriodWindowLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as hwDot3ahEfmErrSymPeriodWindow = ((2^32)*hwDot3ahEfmErrSymPeriodWindowHi) + hwDot3ahEfmErrSymPeriodWindowLo If hwDot3ahEfmErrSymPeriodThreshold symbol errors occur within a window of hwDot3ahEfmErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for hwDot3ahEfmErrSymPeriodWindow is the number of symbols in one second for the underlying physical layer. |
| U32 hwDot3ahEfmErrSymPeriodThresholdHi | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.3 | Unsigned32 | read-write | The two objects hwDot3ahEfmErrSymPeriodThresholdHi and hwDot3ahEfmErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this event. This is defined as hwDot3ahEfmErrSymPeriodThreshold = ((2^32) * hwDot3ahEfmErrSymPeriodThresholdHi) + hwDot3ahEfmErrSymPeriodThresholdLo If hwDot3ahEfmErrSymPeriodThreshold symbol errors occur within a window of hwDot3ahEfmErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for hwDot3ahEfmErrSymPeriodThreshold is one symbol errors. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. |
| U32 hwDot3ahEfmErrSymPeriodThresholdLo | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.4 | Unsigned32 | read-write | The two objects hwDot3ahEfmErrSymPeriodThresholdHi and hwDot3ahEfmErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this event. This is defined as hwDot3ahEfmErrSymPeriodThreshold = ((2^32) * hwDot3ahEfmErrSymPeriodThresholdHi) + hwDot3ahEfmErrSymPeriodThresholdLo If hwDot3ahEfmErrSymPeriodThreshold symbol errors occur within a window of hwDot3ahEfmErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for hwDot3ahEfmErrSymPeriodThreshold is one symbol error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. |
| T/F hwDot3ahEfmErrSymPeriodEvNotifEnable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.5 | TruthValue | read-write | If true, the OAM entity should send an Event Notification OAMPDU when an Errored Symbol Period Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored. |
| U32 hwDot3ahEfmErrFramePeriodWindow | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.6 | Unsigned32 | read-write | The number of frames over which the threshold is defined. The default value of the window is the number of minimum size Ethernet frames that can be received over the physical layer in one second. If hwDot3ahEfmErrFramePeriodThreshold frame errors occur within a window of hwDot3ahEfmErrFramePeriodWindow frames, an Event Notification OAMPDU should be generated with an Errored Frame Period Event TLV indicating the threshold has been crossed in this window. |
| U32 hwDot3ahEfmErrFramePeriodThreshold | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.7 | Unsigned32 | read-write | The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. If hwDot3ahEfmErrFramePeriodThreshold frame errors occur within a window of hwDot3ahEfmErrFramePeriodWindow frames, an Event Notification OAMPDU should be generated with an Errored Frame Period Event TLV indicating the threshold has been crossed in this window. |
| T/F hwDot3ahEfmErrFramePeriodEvNotifEnable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.8 | TruthValue | read-write | If true, the OAM entity should send an Event Notification OAMPDU when an Errored Frame Period Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored. |
| U32 hwDot3ahEfmErrFrameWindow | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.9 | Unsigned32 | read-write | The amount of time (in 100ms increments) over which the threshold is defined. The default value is 10 (1 second). If hwDot3ahEfmErrFrameThreshold frame errors occur within a window of hwDot3ahEfmErrFrameWindow seconds (measured in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Event TLV indicating the threshold has been crossed in this window. |
| U32 hwDot3ahEfmErrFrameThreshold | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.10 | Unsigned32 | read-write | The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. If hwDot3ahEfmErrFrameThreshold frame errors occur within a window of hwDot3ahEfmErrFrameWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Event TLV indicating the threshold has been crossed in this window. |
| T/F hwDot3ahEfmErrFrameEvNotifEnable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.11 | TruthValue | read-write | If true, the OAM entity should send an Event Notification OAMPDU when an Errored Frame Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored. |
| I32 hwDot3ahEfmErrFrameSecsSummaryWindow | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.12 | Integer32 | read-write | The amount of time (in 100ms intervals) over which the threshold is defined. The default value is 600 (60 seconds). If hwDot3ahEfmErrFrameSecsSummaryThreshold frame errors occur within a window of hwDot3ahEfmErrFrameSecsSummaryWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Seconds Summary Event TLV indicating the threshold has been crossed in this window. |
| I32 hwDot3ahEfmErrFrameSecsSummaryThreshold | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.13 | Integer32 | read-write | The number of errored frame seconds that must occur for this event to be triggered. The default value is one errored frame second. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. If hwDot3ahEfmErrFrameSecsSummaryThreshold frame errors occur within a window of hwDot3ahEfmErrFrameSecsSummaryWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Seconds Summary Event TLV indicating the threshold has been crossed in this window. |
| T/F hwDot3ahEfmErrFrameSecsEvNotifEnable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.14 | TruthValue | read-write | If true, the local OAM entity should send an Event Notification OAMPDU when an Errored Frame Seconds Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored. |
| T/F hwDot3ahEfmDyingGaspEnable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.15 | TruthValue | read-write | If true, the local OAM entity should attempt to indicate a dying gasp via the OAMPDU flags field to its peer OAM entity when a dying gasp event occurs. The exact definition of a dying gasp event is implementation dependent. If the system does not support dying gasp capability, setting this object has no effect, and reading the object should always result in 'false'. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored. |
| T/F hwDot3ahEfmCriticalEventEnable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.16 | TruthValue | read-write | If true, the local OAM entity should attempt to indicate a critical event via the OAMPDU flags to its peer OAM entity when a critical event occurs. The exact definition of a critical event is implementation dependent. If the system does not support critical event capability, setting this object has no effect, and reading the object should always result in 'false'. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored. |
| ENA hwDot3ahEfmThresholdTriggerErrDown | 1.3.6.1.4.1.2011.5.25.136.1.2.2.6.1.17 | EnabledStatus | read-write | This object indicates whether threshold event will trigger error-shutdown. If it is enabled(1), after EFM checks that the threshold event happens, the current interface will be set to administrative down. The default value is disabled(2). |
| hwDot3ahEfmEventLogTable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7 | not-accessible | This table records a history of the events that have occurred at the Ethernet OAM level. These events can include locally detected events, which may result in locally generated OAMPDUs, and remotely detected events, which are detected by the OAM peer entity and signaled to the local entity via Ethernet OAM. Ethernet OAM events can be signaled by Event Notification OAMPDUs or by the flags field in any OAMPDU. This table contains both threshold crossing events and non-threshold crossing events. The parameters for the threshold window, threshold value, and actual value (hwDot3ahEfmEventLogWindowXX, hwDot3ahEfmEventLogThresholdXX, hwDot3ahEfmEventLogValue) are only applicable to threshold crossing events, and are returned as all F's (2^32 - 1) for non-threshold crossing events. Entries in the table are automatically created when such events are detected. The size of the table is implementation dependent. When the table reaches its maximum size, older entries are automatically deleted to make room for newer entries. | |
| hwDot3ahEfmEventLogEntry | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1 | not-accessible | An entry in the hwDot3ahEfmEventLogTable. Entries are automatically created whenever Ethernet OAM events occur at the local OAM entity, and when Event Notification OAMPDUs are received at the local OAM entity (indicating events have occurred at the peer OAM entity). The size of the table is implementation dependent, but when the table becomes full, older events are automatically deleted to make room for newer events. The table index hwDot3ahEfmEventLogIndex increments for each new entry, and when the maximum value is reached the value restarts at zero. | |
| U32 hwDot3ahEfmEventLogIndex | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.1 | Unsigned32 | not-accessible | An arbitrary integer for identifying individual events within the event log. |
| TIM hwDot3ahEfmEventLogTimestamp | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.2 | TimeStamp | read-only | The value of sysUpTime at the time of the logged event. For locally generated events, the time of the event can be accurately retrieved from sysUpTime. For remotely generated events, the time of the event is indicated by the reception of the Event Notification OAMPDU indicating the event occurred on the peer. A system may attempt to adjust the timestamp value to more accurately reflect the time of the event at the peer OAM entity by using other information, such as that found in the timestamp found of the Event Notification TLVs, which provides an indication of the relative time between events at the peer entity. |
| HWD hwDot3ahEfmEventLogOui | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.3 | HWDot3Oui | read-only | The OUI of the entity defining the object type. All IEEE 802.3 defined events (as appearing in [802.3ah] except for the Organizationally Unique Event TLVs) use the IEEE 802.3 OUI of 0x0180C2. Organizations defining their own Event Notification TLVs include their OUI in the Event Notification TLV which gets reflected here. |
| U32 hwDot3ahEfmEventLogType | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.4 | Unsigned32 | read-only | The type of event that generated this entry in the event log. When the OUI is the IEEE 802.3 OUI of 0x0180C2, the following event types are defined: erroredSymbolEvent(1), erroredFrameEvent(2), erroredFramePeriodEvent(3), erroredFrameSecondsEvent(4), lostlink(254), linkFault(256), dyingGaspEvent(257), criticalLinkEvent(258) The first four are considered threshold crossing events as they are generated when a metric exceeds a given value within a specified window. The other three are not threshold crossing events. When the OUI is not 71874 (0x0180C2 in hex), then some other organization has defined the event space. If event subtyping is known to the implementation, it may be reflected here. Otherwise, this value should return all Fs (2^32 - 1). |
| INT hwDot3ahEfmEventLogLocation | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.5 | INTEGER | read-only | Whether this event occurred locally (local(1)), or was received from the OAM peer via Ethernet OAM (remote(2)). |
| U32 hwDot3ahEfmEventLogWindowHi | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.6 | Unsigned32 | read-only | If the event represents a threshold crossing event, the two objects hwDot3ahEfmEventWindowHi and hwDot3ahEfmEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (for example, 5, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: hwDot3ahEfmEventLogWindow = ((2^32) * hwDot3ahEfmEventLogWindowHi) + hwDot3ahEfmEventLogWindowLo Otherwise, this value is returned as all F's (2^32 - 1) and adds no useful information. |
| U32 hwDot3ahEfmEventLogWindowLo | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.7 | Unsigned32 | read-only | If the event represents a threshold crossing event, the two objects hwDot3ahEfmEventWindowHi and hwDot3ahEfmEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (for example, 5, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: hwDot3ahEfmEventLogWindow = ((2^32) * hwDot3ahEfmEventLogWindowHi) + hwDot3ahEfmEventLogWindowLo Otherwise, this value is returned as all F's (2^32 - 1) and adds no useful information. |
| U32 hwDot3ahEfmEventLogThresholdHi | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.8 | Unsigned32 | read-only | If the event represents a threshold crossing event, the two objects hwDot3ahEfmEventThresholdHi and hwDot3ahEfmEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (for example, 10, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: hwDot3ahEfmEventLogThreshold = ((2^32) * hwDot3ahEfmEventLogThresholdHi) + hwDot3ahEfmEventLogThresholdLo Otherwise, this value is returned as all F's (2^32 -1) and adds no useful information. |
| U32 hwDot3ahEfmEventLogThresholdLo | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.9 | Unsigned32 | read-only | If the event represents a threshold crossing event, the two objects hwDot3ahEfmEventThresholdHi and hwDot3ahEfmEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (for example, 10, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: hwDot3ahEfmEventLogThreshold = ((2^32) * hwDot3ahEfmEventLogThresholdHi) + hwDot3ahEfmEventLogThresholdLo Otherwise, this value is returned as all F's (2^32 - 1) and adds no useful information. |
| NUM hwDot3ahEfmEventLogValue | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.10 | CounterBasedGauge64 | read-only | If the event represents a threshold crossing event, this value indicates the value of the parameter within the given window that generated this event (for example, 11, when 11 occurrences happened in 5 seconds while the threshold was 10). Otherwise, this value is returned as all F's (2^64 - 1) and adds no useful information. |
| NUM hwDot3ahEfmEventLogRunningTotal | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.11 | CounterBasedGauge64 | read-only | Each Event Notification TLV contains a running total of the number of times an event has occurred, as well as the number of times an Event Notification for the event has been transmitted. For non-threshold crossing events, the number of events (hwDot3ahEfmLogRunningTotal) and the number of resultant Event Notifications (hwDot3ahEfmLogEventTotal) should be identical. For threshold crossing events, since multiple occurrences may be required to cross the threshold, these values are likely different. This value represents the total number of times this event has happened since the last reset (for example, 3253, when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold crossing events since the last reset). |
| U32 hwDot3ahEfmEventLogEventTotal | 1.3.6.1.4.1.2011.5.25.136.1.2.2.7.1.12 | Unsigned32 | read-only | Each Event Notification TLV contains a running total of the number of times an event has occurred, as well as the number of times an Event Notification for the event has been transmitted. For non-threshold crossing events, the number of events (hwDot3ahEfmLogRunningTotal) and the number of resultant Event Notifications (hwDot3ahEfmLogEventTotal) should be identical. For threshold crossing events, since multiple occurrences may be required to cross the threshold, these values are likely different. This value represents the total number of times one or more of these occurrences have resulted in an Event Notification (for example, 51 when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold crossing events since the last reset). |
| hwDot3ahEfmManagerTable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.8 | not-accessible | This table contains configurations of binding relationships between EFM and other modules. | |
| hwDot3ahEfmManagerEntry | 1.3.6.1.4.1.2011.5.25.136.1.2.2.8.1 | not-accessible | This entry contains configurations of binding relationships between EFM and other modules. | |
| ENA hwDot3ahEfmTriggerIfDown | 1.3.6.1.4.1.2011.5.25.136.1.2.2.8.1.1 | EnabledStatus | read-write | This object indicates whether EFM is bound to the interface. If it is enabled(1), after EFM checks that the link times out, the current Ethernet interface link state will be set to block (EFM down),and all the data except the OAMPDU is blocked. The default value is disabled(2). |
| I32 hwDot3ahEfmHoldUpTime | 1.3.6.1.4.1.2011.5.25.136.1.2.2.8.1.2 | Integer32 | read-write | This object specifies the time elapsed an EFM interface is in the faulty state. The value ranges from 0 to 50 in seconds. The default value is 0. |
| hwDot3ahEvrrpTable | 1.3.6.1.4.1.2011.5.25.136.1.2.2.9 | not-accessible | This table contains information about the OAM Evrrp project for a particular Ethernet like interface. | |
| hwDot3ahEvrrpEntry | 1.3.6.1.4.1.2011.5.25.136.1.2.2.9.1 | not-accessible | An entry in the table of hwDot3ahEvrrpTable, containing information on the OAM Evrrp entity for a single Ethernet like interface. Note that there is at most one OAM Evrrp for each Ethernet like interface. | |
| INT hwDot3ahEvrrpCpuState | 1.3.6.1.4.1.2011.5.25.136.1.2.2.9.1.1 | INTEGER | read-only | This object indicates the state in the OAMPDU which sended by the peer interface. If it is master(1), EFM will make the link work as the master state. And if it is slave(2), EFM will make the link works as the slave chain link. The default state is unknown(3). That means the peer interface didn't send any OAMPDU which contains the state of link status. |
| ENA hwDot3ahEvrrpTriggerIfDown | 1.3.6.1.4.1.2011.5.25.136.1.2.2.9.1.2 | EnabledStatus | read-write | This object indicates whether EFM is bound to the interface. If it is enabled(1), after EFM checks that the link times out, the current Ethernet interface link state will be set to EFM down. And all of the PDU operation will be stop. The default value is disabled(2). |
| I32 hwDot3ahEvrrpHoldUpTime | 1.3.6.1.4.1.2011.5.25.136.1.2.2.9.1.3 | Integer32 | read-write | This object specifies the time elapsed an EFM interface is in the faulty state. The value ranges from 0 to 50 in seconds. The default value is 0. |
| hwOamManager | 1.3.6.1.4.1.2011.5.25.136.1.3 | |||
| hwTestMessage | 1.3.6.1.4.1.2011.5.25.136.1.4 | |||
| hwTestMessageObject | 1.3.6.1.4.1.2011.5.25.136.1.4.1 | |||
| U32 hwTestMessageTableNextIndex | 1.3.6.1.4.1.2011.5.25.136.1.4.1.1 | Unsigned32 | read-only | Search the next hwTestMessageTable instance. |
| hwTestMessageTable | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2 | not-accessible | The definition of the tested packets format and the transmission of the tested packets | |
| hwTestMessageEntry | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1 | not-accessible | Entry for Test Message Table. | |
| U32 hwTestMessageIndex | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.1 | Unsigned32 | not-accessible | Set the index for the tested packets table |
| MAC hwTestMessageMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.11 | MacAddress | read-create | The destination MAC address |
| U32 hwTestMessageVlanID | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.12 | Unsigned32 | read-create | VLAN index |
| OCT hwTestMessageInterface | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.13 | OCTET STRING | read-create | If the interface is specified, specify the interface name. |
| OCT hwTestMessageServiceInstance | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.14 | OCTET STRING | read-create | Name of the service instance |
| U32 hwTestMessagePacketSize | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.15 | Unsigned32 | read-create | The length of the sent tested packets ranges from 64 to 1518 in byte, and the default value is 64. |
| U32 hwTestMessageSendPackets | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.16 | Unsigned32 | read-create | The number of the sent tested packets ranges from 1 to 65535 in integer, and the default value is 5. |
| HWT hwTestMessageSendSpeed | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.17 | HWTestMessageSendSpeed | read-create | Enumerated type indicates the rate of sending the packets: oneMbps and fiveMbps. The default is oneMbps. |
| T/F hwTestMessageSendEnabled | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.18 | TruthValue | read-create | The sending and termination of the tested packets |
| HWT hwTestMessageSendFinished | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.19 | HWTestMessageFinishedValue | read-only | View whether the tested packets are stopped to be sent: 1, 2, 3, 4, and 5 indicate that has not run/is running/the previous test terminates normally/the previous test terminates abnormally/the previous test is interrupted (through ctrl+c or mib) |
| ROW hwTestMessageRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.4.1.2.1.51 | RowStatus | read-create | The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated. |
| hwTestMessageResultTable | 1.3.6.1.4.1.2011.5.25.136.1.4.1.3 | not-accessible | View the returned results after tests | |
| hwTestMessageResultEntry | 1.3.6.1.4.1.2011.5.25.136.1.4.1.3.1 | not-accessible | Entry for Test Message Table. | |
| U32 hwTestMessageResultSendPackets | 1.3.6.1.4.1.2011.5.25.136.1.4.1.3.1.11 | Unsigned32 | read-only | The number of the sent packets |
| U32 hwTestMessageResultReceivedPackets | 1.3.6.1.4.1.2011.5.25.136.1.4.1.3.1.12 | Unsigned32 | read-only | The number of the received packets |
| U32 hwTestMessageResultPacketsLost | 1.3.6.1.4.1.2011.5.25.136.1.4.1.3.1.13 | Unsigned32 | read-only | Packets loss ratio |
| U32 hwTestMessageResultSendBytes | 1.3.6.1.4.1.2011.5.25.136.1.4.1.3.1.14 | Unsigned32 | read-only | The number of the sent bytes |
| U32 hwTestMessageResultReceivedBytes | 1.3.6.1.4.1.2011.5.25.136.1.4.1.3.1.15 | Unsigned32 | read-only | The number of the received bytes |
| U32 hwTestMessageResultBytesLost | 1.3.6.1.4.1.2011.5.25.136.1.4.1.3.1.16 | Unsigned32 | read-only | The number of the lost bytes |
| TIM hwTestMessageBeginTimeStamp | 1.3.6.1.4.1.2011.5.25.136.1.4.1.3.1.17 | TimeStamp | read-only | The time of starting the Test operation |
| TIM hwTestMessageEndTimeStamp | 1.3.6.1.4.1.2011.5.25.136.1.4.1.3.1.18 | TimeStamp | read-only | The time of ending the Test operation |
| hwEthOamTraps | 1.3.6.1.4.1.2011.5.25.136.1.6 | |||
| NTF hwDot1agCfmFaultAlarm | 1.3.6.1.4.1.2011.5.25.136.1.6.1 | A MEP has lost contact with one or more MEPs. A notification (fault alarm) is sent to the management entity with the OID of the MEP that has detected the fault. Whenever a MEP loses contact with one or more other MEPs, it may or may not generate a Fault Alarm to warn the system administrator of the problem, as controlled by the MEP Fault Notification Generator State Machine and associated Managed Objects. Only the highest-priority defect, as shown in Table 20-1, is reported in the Fault Alarm. hwDot1agCfmRMepMacAddress The MAC address of the remote faulty MEP hwDot1agCfmRMepHighestPrDefect The fault in the highest level hwDot1agCfmMdName The name of the faulty MD hwDot1agCfmMdLevel The level of the faulty MD hwDot1agCfmMaName The name of the faulty MA | ||
| NTF hwTestMessageFailed | 1.3.6.1.4.1.2011.5.25.136.1.6.2 | The events after tests are reported. 1,2,3,4, and 5 indicate has not run/is running/the previous test terminates normally/the previous test terminate abnormally/the previous test is interrupted. (through ctrl+c or mib) | ||
| NTF hwTestMessageCompleted | 1.3.6.1.4.1.2011.5.25.136.1.6.3 | After the test is complete, report the results to the network management. | ||
| NTF hwDot3ahEfmThresholdEvent | 1.3.6.1.4.1.2011.5.25.136.1.6.4 | A hwDot3ahEfmThresholdEvent notification is sent when a local or remote threshold crossing event is detected. A local threshold crossing event is detected by the local entity, while a remote threshold crossing event is detected by the reception of an Ethernet OAM Event Notification OAMPDU indicating a threshold event. This notification should not be sent more than once per second. The OAM entity can be derived from extracting the ifIndex from the variable bindings. The objects in the notification correspond to the values in a row instance of in the hwDot3ahEfmEventLogTable. The management entity should periodically check hwDot3ahEfmEventLogTable to detect any missed events. | ||
| NTF hwDot3ahEfmNonThresholdEvent | 1.3.6.1.4.1.2011.5.25.136.1.6.5 | A hwDot3ahEfmNonThresholdEvent notification is sent when a local or remote non-threshold crossing event is detected. A local event is detected by the local entity, while a remote event is detected by the reception of an Ethernet OAM Event Notification OAMPDU indicating a non-threshold crossing event. This notification should not be sent more than once per second. The OAM entity can be derived from extracting the ifIndex from the variable bindings. The objects in the notification correspond to the values in a row instance of the hwDot3ahEfmEventLogTable. The management entity should periodically check hwDot3ahEfmEventLogTable to detect any missed events. | ||
| NTF hwDot3ahEfmRemoteDyingGaspEvent | 1.3.6.1.4.1.2011.5.25.136.1.6.8 | A hwDot3ahEfmRemoteDyingGaspEvent notification is sent when a remote Dying-Gasp event is detected. A remote event is detected by the reception of an Ethernet OAM Event Notification OAMPDU indicating a Dying-Gasp event. | ||
| NTF hwDot3ahEfmNonThresholdRecovery | 1.3.6.1.4.1.2011.5.25.136.1.6.17 | A hwDot3ahEfmNonThresholdRecovery notification is sent when a hwDot3ahEfmNonThresholdEvent is recovered. | ||
| NTF hwCfmVlanOnewayDelay | 1.3.6.1.4.1.2011.5.25.136.1.6.23 | In the VLAN networking, the oneway delay exceeded the trap threshold. | ||
| NTF hwCfmVlanOnewayDelayRecovery | 1.3.6.1.4.1.2011.5.25.136.1.6.24 | In the VLAN networking, the oneway delay fell below the trap threshold. | ||
| NTF hwCfmVlanTwowayDelay | 1.3.6.1.4.1.2011.5.25.136.1.6.25 | In the VLAN networking, the twoway delay exceeded the trap threshold. | ||
| NTF hwCfmVlanTwowayDelayRecovery | 1.3.6.1.4.1.2011.5.25.136.1.6.26 | In the VLAN networking, the twoway delay fell below the trap threshold. | ||
| NTF hwDot3ahEfmLoopbackFailed | 1.3.6.1.4.1.2011.5.25.136.1.6.29 | A hwDot3ahEfmLoopbackFailed notification is sent when failed to start loopback on a interface. This notification should not be sent more than once per second. | ||
| NTF hwY1731AisDefectAlarm | 1.3.6.1.4.1.2011.5.25.136.1.6.30 | AIS status has been entered. | ||
| NTF hwY1731AisDefectAlarmRecovery | 1.3.6.1.4.1.2011.5.25.136.1.6.31 | AIS status has been existed. | ||
| NTF hwDot1agCfmUnexpectedMEGLevel | 1.3.6.1.4.1.2011.5.25.136.1.6.32 | Indicates a CCM frame with unexpected MEG level. | ||
| NTF hwDot1agCfmUnexpectedMEGLevelCleared | 1.3.6.1.4.1.2011.5.25.136.1.6.33 | Indicates resuming from receiving a CCM frame with unexpected MEG level. | ||
| NTF hwDot1agCfmMismerge | 1.3.6.1.4.1.2011.5.25.136.1.6.34 | Indicates a CCM frame with unexpected MEG ID | ||
| NTF hwDot1agCfmMismergeCleared | 1.3.6.1.4.1.2011.5.25.136.1.6.35 | Indicates resuming from receiving a CCM frame with unexpected MEG ID. | ||
| NTF hwDot1agCfmUnexpectedMEP | 1.3.6.1.4.1.2011.5.25.136.1.6.36 | Indicates a CCM frame with unexpected MEP ID. | ||
| NTF hwDot1agCfmUnexpectedMEPCleared | 1.3.6.1.4.1.2011.5.25.136.1.6.37 | Indicates resuming from receiving a CCM frame with unexpected MEP ID. | ||
| NTF hwDot1agCfmUnexpectedPeriod | 1.3.6.1.4.1.2011.5.25.136.1.6.38 | Indicates a CCM frame with unexpected period. | ||
| NTF hwDot1agCfmUnexpectedPeriodCleared | 1.3.6.1.4.1.2011.5.25.136.1.6.39 | Indicates resuming from receiving a CCM frame with unexpected period. | ||
| NTF hwDot1agCfmUnexpectedMAC | 1.3.6.1.4.1.2011.5.25.136.1.6.40 | Indicates a CCM frame with unexpected MAC. | ||
| NTF hwDot1agCfmUnexpectedMACCleared | 1.3.6.1.4.1.2011.5.25.136.1.6.41 | Indicates a CCM frame with unexpected MAC. | ||
| NTF hwDot1agCfmLOC | 1.3.6.1.4.1.2011.5.25.136.1.6.42 | Indicates that the session losses of continuity. | ||
| NTF hwDot1agCfmLOCCleared | 1.3.6.1.4.1.2011.5.25.136.1.6.43 | Indicates that the session resumes from lossing of continuity. | ||
| NTF hwDot1agCfmExceptionalMACStatus | 1.3.6.1.4.1.2011.5.25.136.1.6.44 | Indicates the remote MEP is reporting an error status in its Port Status TLV or Interface Status TLV. | ||
| NTF hwDot1agCfmExceptionalMACStatusCleared | 1.3.6.1.4.1.2011.5.25.136.1.6.45 | Indicates the remote MEP resumes from an error status indicated in its Port Status TLV or Interface Status TLV. | ||
| NTF hwDot1agCfmRDI | 1.3.6.1.4.1.2011.5.25.136.1.6.46 | Indicates that MEP receives a CCM frame with the RDI field set. | ||
| NTF hwDot1agCfmRDICleared | 1.3.6.1.4.1.2011.5.25.136.1.6.47 | Indicates that MEP receives a CCM frame with the RDI field cleared. | ||
| NTF hwY1731AisExceedMaxPktNum | 1.3.6.1.4.1.2011.5.25.136.1.6.48 | Indicates that the number of AIS packets transmitted in one second exceeds the upper limit. | ||
| NTF hwY1731AisExceedMaxPktNumCleared | 1.3.6.1.4.1.2011.5.25.136.1.6.49 | Indicates that the number of AIS packets transmitted in one second under the upper limit. | ||
| NTF hwY1731LckDefect | 1.3.6.1.4.1.2011.5.25.136.1.6.50 | LCK status has been entered. | ||
| NTF hwY1731LckDefectCleared | 1.3.6.1.4.1.2011.5.25.136.1.6.51 | LCK status has been exited. | ||
| NTF hwY1731Statistic | 1.3.6.1.4.1.2011.5.25.136.1.6.52 | The Y.1731 statistic value exceeded the upper limit value of the threshold. | ||
| NTF hwY1731StatisticClear | 1.3.6.1.4.1.2011.5.25.136.1.6.53 | The Y.1731 statistic value fell below lower limit value of the threshold. | ||
| NTF hwY1731LckExceedThreshold | 1.3.6.1.4.1.2011.5.25.136.1.6.54 | Indicates that the number of LCK packets transmitted in 1 second exceeds the upper limit. | ||
| NTF hwY1731LckExceedThresholdRecovery | 1.3.6.1.4.1.2011.5.25.136.1.6.55 | Indicates that the number of LCK packets transmitted in 1 second falls below the lower limit. | ||
| hwEthOamConformance | 1.3.6.1.4.1.2011.5.25.136.1.7 | |||
| hwEthOamCompliances | 1.3.6.1.4.1.2011.5.25.136.1.7.1 | |||
| hwEthOamCompliance | 1.3.6.1.4.1.2011.5.25.136.1.7.1.1 | The compliance statement for the HUAWEI-ETHOAM-MIB | ||
| hwEthOamGroups | 1.3.6.1.4.1.2011.5.25.136.1.7.2 | |||
| hwDot1agCfmMdGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.1 | Objects for the hwDot1agCfmMd group. | ||
| hwDot1agCfmMaGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.2 | Objects for the hwDot1agCfmMa group. | ||
| hwDot1agCfmMepGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.3 | Objects for the hwDot1agCfmMep group. | ||
| hwDot1agCfmRMepGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.4 | RMEP configuration group | ||
| hwDot1agCfmMipGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.5 | MIP configuration group | ||
| hwDot1agCfmMacPingGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.6 | Gmac Ping starting and statistics group | ||
| hwDot1agCfmMacTraceGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.7 | Mac Trace starting and statistics group | ||
| hwDot1agCfmMacTraceReplyGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.8 | Gmac Trace starting and statistics group | ||
| hwDot1agCfmQueryMdIndexGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.9 | Querying MD index group | ||
| hwDot1agCfmQueryMaIndexGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.10 | Querying MA index group | ||
| hwDot3ahEfmDetectModeGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.11 | Test mode group | ||
| hwTestMessageGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.12 | Test packets setting group | ||
| hwTestMessageResultGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.13 | The group for the tested packets results to be returned. | ||
| hwEthOamTrapsGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.14 | Objects for the Notifications group. A collection of notifications used by Ethernet OAM to signal to a management entity that local or remote events have occurred on a specified Ethernet link. This group is optional for all IEEE 802.3 OAM implementations. Since the information in the notifications is dependent on the hwDot3ahEfmEventLogTable, that table must be implemented for notifications. | ||
| hwDot1agCfmGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.15 | Cfm enabling and statistics group | ||
| hwDot3ahEfmControlGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.16 | A collection of objects providing the abilities, configuration, and status of an Ethernet OAM entity. | ||
| hwDot3ahEfmPeerGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.17 | A collection of objects providing the abilities, configuration, and status of a peer Ethernet OAM entity. | ||
| hwDot3ahEfmStatsBaseGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.18 | A collection of objects providing the statistics for the number of various transmit and receive events for OAM on an Ethernet like interface. Note that all of these counters must be supported even if the related function (as described in hwDot3ahEfmFunctionsSupported) is not supported. | ||
| hwDot3ahEfmLoopbackGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.19 | A collection of objects for controlling the OAM remote loopback function. | ||
| hwDot3ahEfmErrSymbolPeriodEventGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.20 | A collection of objects for configuring the thresholds for an Errored Symbol Period Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other. | ||
| hwDot3ahEfmErrFramePeriodEventGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.21 | A collection of objects for configuring the thresholds for an Errored Frame Period Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other. | ||
| hwDot3ahEfmErrFrameEventGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.22 | A collection of objects for configuring the thresholds for an Errored Frame Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other. | ||
| hwDot3ahEfmErrFrameSecsSummaryEventGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.23 | A collection of objects for configuring the thresholds for an Errored Frame Seconds Summary Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other. | ||
| hwDot3ahEfmFlagEventGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.24 | A collection of objects for configuring the sending OAMPDUs with the critical event flag or dying gasp flag enabled. | ||
| hwDot3ahEfmEventLogGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.25 | A collection of objects for configuring the thresholds for an Errored Frame Seconds Summary Event and maintaining the event information. | ||
| hwDot3ahEfmManagerGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.26 | hwDot3ahEfmManagerGroup | ||
| hwDot3ahEvrrpGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.27 | A collection of objects for displaying and maintaining the infomation for Evrrp state. | ||
| hwY1731BaseConfigGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.28 | A collection of objects for configuring OAM functions for base. | ||
| hwY1731ConfigGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.29 | A collection of objects for configuring OAM functions for performance monitoring. | ||
| hwY1731AisGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.30 | A collection of objects for configuring the Alarm Indication Signal (AIS) function to suppress alarms. | ||
| hwY1731AisVlanGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.31 | A collection of objects for configuring the information about the VLAN that receives AIS frames. | ||
| hwY1731AisLinkStatusGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.32 | A collection of objects for configuring sending AIS packets when the status of the interface which is monitored goes down. | ||
| hwY1731MulPingGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.33 | A collection of objects for configuring the multicast MAC ping function. | ||
| hwY1731MulPingReplyGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.34 | A collection of objects for displaying information about the multicast LBRs for responding to the multicast MAC ping operation. | ||
| hwY1731ResetStatisticGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.35 | A collection of objects for reset Y1731 statistic information. | ||
| hwY1731ManagerGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.36 | Y.1731 detecting group | ||
| hwY1731AisVlanConfigGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.37 | A collection of objects for configuring the information about the VLAN that receives AIS frames. | ||
| hwDot1agCfmMPGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.38 | Querying MP group | ||
| hwY1731TestIdGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.39 | A collection of objects for configuring the information about TestId. | ||
| hwY1731TestIdSingleEndedLMSendGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.40 | A collection of objects for configuring the information about the single-ended ETH-LM sending function. | ||
| hwY1731TestIdSingleEndedLMReceiveGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.41 | A collection of objects for configuring the information about the single-ended ETH-LM receiving function. | ||
| hwY1731TestIdOneWayDMSendGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.42 | A collection of objects for configuring the information about the one-way ETH-DM sending function. | ||
| hwY1731TestIdOneWayDMReceiveGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.43 | A collection of objects for configuring the information about the one-way ETH-DM receiving function. | ||
| hwY1731TestIdTwoWayDMSendGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.44 | A collection of objects for configuring the information about the two-way ETH-DM sending function. | ||
| hwY1731TestIdTwoWayDMReceiveGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.45 | A collection of objects for configuring the information about the two-way ETH-DM receiving function. | ||
| hwY1731TestIdSingleLossStatTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.46 | A collection of objects for storing the result of single-ended ETH-LM. | ||
| hwY1731TestIdOneDelayStatTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.47 | A collection of objects for storing the result of one-way ETH-DM. | ||
| hwY1731TestIdTwoDelayStatTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.48 | A collection of objects for storing the result of two-way ETH-DM. | ||
| hwY1731TestIdStatisticResetTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.49 | A collection of objects for reseting Y1731 statistic information. | ||
| hwY1731TestIdTwoDelaySummaryStatTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.50 | A collection of objects for storing the statistics of two-way ETH-DM collected during the last period. | ||
| hwY1731TestIdSingleSynLossSummaryStatTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.51 | A collection of objects for storing the statistics of single-ended ETH-SLM collected during the last period. | ||
| hwY1731SingleLossSummaryStatTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.52 | A collection of objects for storing the statistics of single-ended ETH-LM collected during the last period. | ||
| hwY1731TestIdSingleSynEndedLMSendTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.53 | A collection of objects for configuring the information about the single-ended ETH-SLM sending function. | ||
| hwY1731TestIdSingleSynEndedLMReceiveTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.54 | A collection of objects for configuring the information about the single-ended ETH-SLM receive function. | ||
| hwY1731TestIdSingleLossSummaryStatTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.55 | A collection of objects for configuring the information about the single-ended ETH-LM collected during the last period. | ||
| hwY1731TestIdSingleSynLossStatTableGroup | 1.3.6.1.4.1.2011.5.25.136.1.7.2.56 | A collection of objects for storing the result of single-ended ETH-SLM. | ||
| hwEthOamY1731 | 1.3.6.1.4.1.2011.5.25.136.1.8 | |||
| hwY1731ConfigObject | 1.3.6.1.4.1.2011.5.25.136.1.8.1 | |||
| hwY1731BaseConfigTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.1 | not-accessible | This table is used to configure OAM functions for base. | |
| hwY1731BaseConfigEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.1.1 | not-accessible | The configuration entry of base config. | |
| INT hwY1731PwMeasureMode | 1.3.6.1.4.1.2011.5.25.136.1.8.1.1.1.1 | INTEGER | read-write | This object indicates the PW measure mode. The value can be: invalid symmetry asymmetry If MA associates with a VLAN, the value is invalid. If MA associates with VSI or VLL, the default value is asymmetry. |
| U32 hwY1731OneDelayThreshold | 1.3.6.1.4.1.2011.5.25.136.1.8.1.1.1.2 | Unsigned32 | read-write | This object indicates the alarm threshold for the one-way ETH-DM. This object can be set only in VLAN. The value ranges from 1 to 4294967295. If hwY1731OneDelayThreshold is set to 0, the default alarm threshold of the one-way frame delay is used. By default, no alarm threshold of the one-way frame delay is set. |
| U32 hwY1731TwoDelayThreshold | 1.3.6.1.4.1.2011.5.25.136.1.8.1.1.1.3 | Unsigned32 | read-write | This object indicates the alarm threshold for the two-way ETH-DM. This object can be set only in VLAN. The value ranges from 1 to 4294967295. If hwY1731TwoDelayThreshold is set to 0, the default alarm threshold of the two-way frame delay is used. By default, no alarm threshold of the two-way frame delay is set. |
| hwY1731ConfigTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2 | not-accessible | This table is used to configure OAM functions for performance monitoring. | |
| hwY1731ConfigEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1 | not-accessible | The configuration entry of performance monitoring functions. | |
| IP hwY1731RemoteIp | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.1 | IpAddress | not-accessible | This object indicates the IP address of the remote end. |
| U32 hwY1731VcId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.2 | Unsigned32 | not-accessible | This object indicates the VC ID. |
| MAC hwY1731MacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.3 | MacAddress | not-accessible | This object indicates the MAC address of the remote end. |
| I32 hwY1731ResvIndex | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.4 | Integer32 | not-accessible | This object indicates the index for reserve. |
| INT hwY1731ServiceType | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.5 | INTEGER | read-only | This object indicates the type of service. The service can be: vlan vsi vll unbind |
| ENA hwY1731SingleLossRecvEnable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.6 | EnabledStatus | read-create | This object indicates whether the single-ended ETH-LM receiving is enabled on the MEP in the MA to implement the single-ended ETH-LM. The value can be: enabled disabled By default, the value is disabled. |
| ENA hwY1731OneDelayRecvEnable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.7 | EnabledStatus | read-create | This object indicates whether the one-way ETH-DM receiving is enabled on the MEP in the MA to implement the one-way ETH-DM. The value can be: enabled disabled By default, the value is disabled. |
| T/F hwY1731OneDelayRecvEnableIsContinue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.8 | TruthValue | read-create | This object indicates whether the one-way ETH-DM receiving is continual. |
| ENA hwY1731TwoDelayRecvEnable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.9 | EnabledStatus | read-create | This object indicates whether the two-way ETH-DM receiving is enabled on the MEP in the MA to implement the two-way ETH-DM. The value can be: enabled disabled By default, the value is disabled. |
| ENA hwY1731SingleLossEnable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.10 | EnabledStatus | read-create | This object indicates whether the single-ended ETH-LM sending is enabled. The value can be: enabled disabled By default, the value is disabled. |
| T/F hwY1731SingleLossIsContinue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.11 | TruthValue | read-create | This object indicates whether the single-ended ETH-LM sending is continual. If the value is 'false', it indicates that the single-ended ETH-LM is on-demand. |
| I32 hwY1731SingleLossMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.12 | Integer32 | read-create | This object indicates the ID of the local MEP that is specified in the single-ended ETH-LM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value. |
| T/F hwY1731SingleLossDestIsMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.13 | TruthValue | read-create | This object indicates whether the destination MAC address of the single-ended ETH-LM is the specified RMEP's MAC address. |
| I32 hwY1731SingleLossDestMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.14 | Integer32 | read-create | This object indicates the ID of the remote MEP that is specified in the single-ended ETH-LM operation. The value 0 is an invalid value. |
| MAC hwY1731SingleLossMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.15 | MacAddress | read-create | This object indicates the MAC address of the remote end. |
| INT hwY1731SingleLossInterval | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.16 | INTEGER | read-create | This object indicates the interval of the sent LMM frames. When on-demand OAM, the value can be: 1 second 10 seconds When proactive OAM, the value can be: 1 second 10 seconds 30 seconds |
| I32 hwY1731SingleLossCount | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.17 | Integer32 | read-create | This object indicates the number of LMM frames to be sent. The value can be 0 or ranges from 1 to 60. When proactive OAM, the value is 0. |
| I32 hwY1731SingleLoss8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.18 | Integer32 | read-create | This object indicates the 802.1p priority of the sent LMM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set. |
| ENA hwY1731DualLossEnable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.19 | EnabledStatus | read-create | This object indicates whether the dual-ended ETH-LM is enabled. The value can be: enabled disabled By default, the value is disabled. |
| I32 hwY1731DualLossMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.20 | Integer32 | read-create | This object indicates the ID of the local MEP that is specified in the dual-ended ETH-LM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value. |
| I32 hwY1731DualLossDestMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.21 | Integer32 | read-create | This object indicates the ID of the remote MEP that is specified in the dual-ended ETH-LM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value. |
| ENA hwY1731OneDelayEnable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.22 | EnabledStatus | read-create | This object indicates whether the one-way ETH-DM sending is enabled. The value can be: enabled disabled By default, the value is disabled. |
| T/F hwY1731OneDelayIsContinue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.23 | TruthValue | read-create | This object indicates whether the one-way ETH-DM sending is continual. If the value is 'false', it indicates that the one-way ETH-DM is on-demand. |
| I32 hwY1731OneDelayMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.24 | Integer32 | read-create | This object indicates the ID of the local MEP that is specified in the one-way ETH-DM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value. |
| T/F hwY1731OneDelayDestIsMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.25 | TruthValue | read-create | This object indicates whether the destination MAC address of the one-way ETH-DM is the specified RMEP's MAC address. |
| I32 hwY1731OneDelayDestMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.26 | Integer32 | read-create | This object indicates the ID of the remote MEP that is specified in the one-way ETH-DM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value. |
| MAC hwY1731OneDelayMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.27 | MacAddress | read-create | This object indicates the MAC address of the RMEP. |
| INT hwY1731OneDelayInterval | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.28 | INTEGER | read-create | This object indicates the interval of the sent 1DM frames. When on-demand OAM, the value can be: 1 second 10 seconds When proactive OAM, the value can be: 1 second 10 seconds 30 seconds |
| I32 hwY1731OneDelayCount | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.29 | Integer32 | read-create | This object indicates the number of the sent 1DM frames. The value can be 0 or ranges from 1 to 60. When proactive OAM, the value is 0. |
| I32 hwY1731OneDelay8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.30 | Integer32 | read-create | This object indicates the 802.1p priority of the sent 1DM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0, 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set. |
| ENA hwY1731TwoDelayEnable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.31 | EnabledStatus | read-create | This object indicates whether the two-way ETH-DM sending is enabled. |
| T/F hwY1731TwoDelayIsContinue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.32 | TruthValue | read-create | This object indicates whether the two-way ETH-DM sending is continual. If the value is 'false', it indicates that the two-way ETH-DM is on-demand. |
| I32 hwY1731TwoDelayMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.33 | Integer32 | read-create | This object indicates the ID of the local MEP that is specified in the two-way ETH-DM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value. |
| T/F hwY1731TwoDelayDestIsMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.34 | TruthValue | read-create | This object indicates whether the destination MAC address of the two-way ETH-DM is the specified RMEP's MAC address. |
| I32 hwY1731TwoDelayDestMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.35 | Integer32 | read-create | This object indicates the ID of the remote MEP that is specified in the two-way ETH-DM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value. |
| MAC hwY1731TwoDelayMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.36 | MacAddress | read-create | This object indicates the destination MAC address. |
| INT hwY1731TwoDelayInterval | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.37 | INTEGER | read-create | This object indicates the interval of the sent DMM frames. When on-demand OAM, the value can be: 1 second 10 seconds When proactive OAM, the value can be: 1 second 10 seconds 30 seconds |
| I32 hwY1731TwoDelayCount | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.38 | Integer32 | read-create | This object indicates the number of the sent DMM frames. The value can be 0 or ranges from 1 to 60. When proactive OAM, the value is 0. |
| I32 hwY1731TwoDelay8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.39 | Integer32 | read-create | This object indicates the 802.1p priority of the sent DMM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set. |
| I32 hwY1731SingleLossRecv8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.40 | Integer32 | read-create | This object indicates the 802.1p priority of the received LMM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set. |
| I32 hwY1731OneDelayRecv8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.41 | Integer32 | read-create | This object indicates the 802.1p priority of the received 1DM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set. |
| I32 hwY1731TwoDelayRecv8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.42 | Integer32 | read-create | This object indicates the 802.1p priority of the received DMM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set. |
| I32 hwY1731SingleLossRecvMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.43 | Integer32 | read-create | This object indicates the ID of the local MEP. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value. |
| I32 hwY1731OneDelayRecvMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.44 | Integer32 | read-create | This object indicates the ID of the local MEP. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value. |
| I32 hwY1731TwoDelayRecvMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.45 | Integer32 | read-create | This object indicates the ID of the local MEP. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value. |
| I32 hwY1731OneDelayPacketSize | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.46 | Integer32 | read-create | This object indicates the size of one-way ETH-DM packet. The value can be 0 or ranges from 64 to 1518. The value 0 means that the packet size is not specified. By default, the value is 0. |
| I32 hwY1731TwoDelayPacketSize | 1.3.6.1.4.1.2011.5.25.136.1.8.1.2.1.47 | Integer32 | read-create | This object indicates the size of a two-way ETH-DM packet. The value can be 0 or ranges from 64 to 1518. The value 0 means that the packet size is not specified. By default, the value is 0. |
| hwY1731AisTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.3 | not-accessible | This table is used to configure the Alarm Indication Signal (AIS) function to suppress alarms. | |
| hwY1731AisEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.3.1 | not-accessible | The entry of alarm indication signal. | |
| ENA hwY1731AisEnable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.3.1.1 | EnabledStatus | read-create | This object indicates whether the AIS function is enabled in the current MA. The value of this object can be: enabled disabled By default, the value is disabled. |
| I32 hwY1731AisSendLevel | 1.3.6.1.4.1.2011.5.25.136.1.8.1.3.1.2 | Integer32 | read-create | This object indicates the level of the sent AIS frames. The value can be -1 or ranges from 0 to 7. The value -1 is an invalid value. |
| INT hwY1731AisSendInterval | 1.3.6.1.4.1.2011.5.25.136.1.8.1.3.1.3 | INTEGER | read-create | This object indicates the interval of the sent AIS frames. The value can be: 1 second 60 seconds The default value is 1 second. |
| ENA hwY1731AisSendPktStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.3.1.4 | EnabledStatus | read-only | This object indicates whether the current MA is sending AIS frames. The value can be: enabled disabled By default, the value is disabled. |
| ENA hwY1731AisSuppressEnable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.3.1.5 | EnabledStatus | read-create | This object indicates whether the alarm suppression function is enabled. The value can be: enabled disabled By default, the value is disabled. |
| ENA hwY1731AisSuppressStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.3.1.6 | EnabledStatus | read-only | This object indicates whether the alarm function on the current device is in the suppression state. The value can be: enabled disabled |
| hwY1731AisVlanTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.4 | not-accessible | This table is used to configure the information about the VLAN that receives AIS frames. | |
| hwY1731AisVlanEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.4.1 | not-accessible | The entry of alarm indication signal about vlan infomation. | |
| VLA hwY1731AisPeVlan | 1.3.6.1.4.1.2011.5.25.136.1.8.1.4.1.1 | VlanIdOrNone | read-create | This object indicates the ID of the PE VLAN corresponding to the AIS function. |
| VLA hwY1731AisLowCeVlan | 1.3.6.1.4.1.2011.5.25.136.1.8.1.4.1.2 | VlanIdOrNone | read-create | This object indicates the lower limit of the ID of the CE VLAN corresponding to the AIS function. |
| VLA hwY1731AisHighCeVlan | 1.3.6.1.4.1.2011.5.25.136.1.8.1.4.1.3 | VlanIdOrNone | read-create | This object indicates the upper limit of the ID of the CE VLAN corresponding to the AIS function. |
| VLA hwY1731AisLowDot1qVlan | 1.3.6.1.4.1.2011.5.25.136.1.8.1.4.1.4 | VlanIdOrNone | read-create | This object indicates the lower limit of the ID of the dot1q VLAN corresponding to the AIS function. |
| VLA hwY1731AisHighDot1qVlan | 1.3.6.1.4.1.2011.5.25.136.1.8.1.4.1.5 | VlanIdOrNone | read-create | This object indicates the upper limit of the ID of the dot1q VLAN corresponding to the AIS function. |
| ROW hwY1731AisRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.4.1.99 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwY1731AisLinkStatusTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.5 | not-accessible | This table is used to enable Y.1731 to send AIS packets when the status of the interface which is monitored goes down. | |
| hwY1731AisLinkStatusEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.5.1 | not-accessible | The entry of AIS monitoring the link status of the interface. | |
| NUM hwY1731AisLinkStatusIfIndex | 1.3.6.1.4.1.2011.5.25.136.1.8.1.5.1.1 | InterfaceIndex | not-accessible | This object indicates the index of the interface which is monitored by AIS. |
| ROW hwY1731AisLinkRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.5.1.20 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwY1731MulPingTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6 | not-accessible | This table is used to configure the multicast MAC ping function. | |
| hwY1731MulPingEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1 | not-accessible | The entry of multicast ping. | |
| U32 hwY1731MulPingIndex | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.1 | Unsigned32 | not-accessible | This object indicates the index of this table. |
| ENA hwY1731MulPingState | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.2 | EnabledStatus | read-create | This object indicates whether the multicast MAC ping function is enabled. The value can be: enabled disabled By default, the value is disabled. |
| OCT hwY1731MulPingMdName | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.3 | OCTET STRING | read-create | This object indicates the name of the MD that initiates the multicast MAC ping. |
| OCT hwY1731MulPingMaName | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.4 | OCTET STRING | read-create | This object indicates the name of the MA that initiates the multicast MAC ping. |
| I32 hwY1731MulPingMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.5 | Integer32 | read-create | This object indicates the ID of the local MEP of the 802.1ag MAC multicast ping operation. The value ranges from 1 to 8191. By default, the value is 0. |
| U32 hwY1731MulPingTimeout | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.6 | Unsigned32 | read-create | This object indicates the timeout period of the multicast MAC ping. The value ranges from 1 to 65535, in milliseconds. By default, the value is 5000. |
| U32 hwY1731MulPingCount | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.7 | Unsigned32 | read-create | This object indicates the number of the sent multicast LBM packets. By default, the value is 3. |
| I32 hwY1731MulPingPriority | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.8 | Integer32 | read-create | This object indicates the priority of the sent LBM packets. The value ranges from 0 to 7 or can be 255. The value 255 is an invalid value. The greater the value is, the higher the priority is. |
| C32 hwY1731MulPingSendPacketNum | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.9 | Counter32 | read-only | This object indicates the number of multicast LBM packets that have been sent. |
| C32 hwY1731MulPingRecvPacketNum | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.10 | Counter32 | read-only | This object indicates the number of multicast LBM packets that have been received. |
| U32 hwY1731MulPingRecvTimeDelayMin | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.11 | Unsigned32 | read-only | This object indicates the minimum delay after which LBR packets are received. |
| U32 hwY1731MulPingRecvTimeDelayMax | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.12 | Unsigned32 | read-only | This object indicates the maximum delay after which LBR packets are received. |
| U32 hwY1731MulPingRecvTimeDelayAvg | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.13 | Unsigned32 | read-only | This object indicates the average delay after which LBR packets are received. |
| ROW hwY1731MulPingRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.6.1.99 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwY1731MulPingReplyTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.7 | not-accessible | This table is used to display information about the multicast LBRs for responding to the multicast MAC ping operation. | |
| hwY1731MulPingReplyEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.7.1 | not-accessible | The entry of multicast ping reply. | |
| U32 hwY1731MulPingReplySeqNumber | 1.3.6.1.4.1.2011.5.25.136.1.8.1.7.1.1 | Unsigned32 | not-accessible | This object indicates the sequence number of the multicast LBR. |
| U32 hwY1731MulPingReplyOrder | 1.3.6.1.4.1.2011.5.25.136.1.8.1.7.1.2 | Unsigned32 | not-accessible | This object indicates the order in which multicast LBRs are received. |
| I32 hwY1731MulPingReplyMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.7.1.3 | Integer32 | read-only | This object indicates the MEP ID carried in the multicast LBRs. The value ranges from 0 to 8191. The value 0 is an invalid value. |
| MAC hwY1731MulPingReplyMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.1.7.1.4 | MacAddress | read-only | This object indicates the MAC address carried in the multicast LBRs. |
| U32 hwY1731MulPingReplyTransTime | 1.3.6.1.4.1.2011.5.25.136.1.8.1.7.1.5 | Unsigned32 | read-only | This object indicates the period from the time when the multicast LBM is sent to the time when the multicast LBR is received. |
| hwY1731AisVlanConfigTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.8 | not-accessible | This table is used to configure the information about the VLAN that receives AIS frames. | |
| hwY1731AisVlanConfigEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.8.1 | not-accessible | The entry of alarm indication signal about vlan infomation. | |
| VLA hwY1731AisConfigPeVlan | 1.3.6.1.4.1.2011.5.25.136.1.8.1.8.1.1 | VlanIdOrNone | not-accessible | This object indicates the ID of the PE VLAN corresponding to the AIS function. The value 0 indicates that the PE VLAN is not set. |
| OCT hwY1731AisConfigVlanListLow | 1.3.6.1.4.1.2011.5.25.136.1.8.1.8.1.2 | OCTET STRING | read-create | If hwY1731AisConfigPeVlan is set to 0, the object indicates a VLAN list corresponding to the AIS function. If its value is not 0, this object indicates a CE VLAN list. The VLAN ID ranges 1 to 2047. The hwY1731AisConfigVlanListHigh value ranges 2048 to 4094. |
| OCT hwY1731AisConfigVlanListHigh | 1.3.6.1.4.1.2011.5.25.136.1.8.1.8.1.3 | OCTET STRING | read-create | If hwY1731AisConfigPeVlan is set to 0, the object indicates a VLAN list corresponding to the AIS function. If its value is not 0, this object indicates a CE VLAN list. The VLAN ID ranges 2048 to 4094. The hwY1731AisConfigVlanListLow value ranges value 1 to 2047. |
| ROW hwY1731AisVlanConfigRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.8.1.4 | RowStatus | read-create | This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated. |
| hwY1731TestIdTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9 | not-accessible | This table defines the information about TestId. | |
| hwY1731TestIdEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1 | not-accessible | The configuration entry of TestId. | |
| U32 hwY1731TestIdentifier | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.1 | Unsigned32 | read-only | This object indicates the ID of the test. |
| OCT hwY1731TestIdMdName | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.2 | OCTET STRING | read-create | This object indicates the name of the MD in which TestId is configured. |
| OCT hwY1731TestIdMaName | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.3 | OCTET STRING | read-create | This object indicates the name of the MA in which TestId is configured. |
| I32 hwY1731TestIdLocalMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.4 | Integer32 | read-create | This object indicates the ID of the local MEP that is specified in the TestId configuration. |
| T/F hwY1731TestIdDestIsMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.5 | TruthValue | read-create | This object indicates whether the destination MAC address is the specified RMEP's MAC address. The default value is false. |
| I32 hwY1731TestIdDestMepId | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.6 | Integer32 | read-create | This object indicates the ID of the remote MEP that is specified in the TestId configuration. |
| MAC hwY1731TestIdDestMepMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.7 | MacAddress | read-create | This object indicates the MAC address of the remote end. |
| MAC hwY1731TestIdOnwardMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.8 | MacAddress | read-create | This object indicates the onward MAC address. |
| MAC hwY1731TestIdBackwardMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.9 | MacAddress | read-create | This object indicates the backward MAC address. |
| T/F hwY1731TestIdIsUpdateOnwardMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.10 | TruthValue | read-create | This object indicates whether the onward MAC address is updated automatically. The default value is false. |
| T/F hwY1731TestIdIsUpdateBackwardMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.11 | TruthValue | read-create | This object indicates whether the backward MAC address is updated automatically. The default value is false. |
| I32 hwY1731TestId8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.12 | Integer32 | read-create | This object indicates the 802.1p priority. The value 255 is an invalid value. |
| I32 hwY1731TestIdUplink8021p | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.13 | Integer32 | read-create | This object indicates the 802.1p priority of uplink packets. The value 255 is an invalid value. |
| I32 hwY1731TestIdDownlink8021p | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.14 | Integer32 | read-create | This object indicates the 802.1p priority of downlink packets. The value 255 is an invalid value. |
| OCT hwY1731TestIdDescription | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.15 | OCTET STRING | read-create | This object indicates the description of TestId. |
| T/F hwY1731TestIdIsRecordFile | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.16 | TruthValue | read-create | This object indicates whether the statistics of the testid will be recorded in testid file. The default value is false. |
| INT hwY1731TestIdQueuePriority | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.17 | INTEGER | read-create | This object indicates the queue priority. The queue priority can be (1..9). |
| ROW hwY1731TestIdRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.9.1.99 | RowStatus | read-create | This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated. |
| hwY1731TestIdSingleEndedLMSendTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.10 | not-accessible | This table configures the single-ended ETH-LM sending function. | |
| hwY1731TestIdSingleEndedLMSendEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.10.1 | not-accessible | The configuration entry of the single-ended ETH-LM sending function. | |
| T/F hwY1731TestIdSingleEndedLMSendIsContinue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.10.1.1 | TruthValue | read-create | This object indicates whether single-ended ETH-LM sending is continual. If the value is 'false', it indicates that the single-ended ETH-LM is on-demand. |
| INT hwY1731TestIdSingleEndedLMSendInterval | 1.3.6.1.4.1.2011.5.25.136.1.8.1.10.1.2 | INTEGER | read-create | This object indicates the interval at which LMM frames are sent. the value can be: 1 second 10 seconds 30 seconds 60 seconds |
| I32 hwY1731TestIdSingleEndedLMSendCount | 1.3.6.1.4.1.2011.5.25.136.1.8.1.10.1.3 | Integer32 | read-create | This object indicates the number of the sent LMM frames. The value can be 0 or ranges from 1 to 60. In a proactive OAM scenario, the value is 0. |
| ROW hwY1731TestIdSingleEndedLMSendRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.10.1.99 | RowStatus | read-create | This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated. |
| hwY1731TestIdSingleEndedLMReceiveTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.11 | not-accessible | This table configures the single-ended ETH-LM receiving function. | |
| hwY1731TestIdSingleEndedLMReceiveEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.11.1 | not-accessible | The configuration entry of the single-ended ETH-LM receiving function. | |
| ROW hwY1731TestIdSingleEndedLMReceiveRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.11.1.99 | RowStatus | read-create | This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated. |
| hwY1731TestIdOneWayDMSendTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.12 | not-accessible | This table configures the one-way ETH-DM sending function. | |
| hwY1731TestIdOneWayDMSendEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.12.1 | not-accessible | The configuration entry of the one-way ETH-DM sending function. | |
| T/F hwY1731TestIdOneWayDMSendIsContinue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.12.1.1 | TruthValue | read-create | This object indicates whether one-way ETH-DM sending is continual. If the value is 'false', it indicates that one-way ETH-DM is on-demand. |
| INT hwY1731TestIdOneWayDMSendInterval | 1.3.6.1.4.1.2011.5.25.136.1.8.1.12.1.2 | INTEGER | read-create | This object indicates the interval at which 1DM frames are sent. the value can be: 1 second 10 seconds 30 seconds 60 seconds |
| I32 hwY1731TestIdOneWayDMSendCount | 1.3.6.1.4.1.2011.5.25.136.1.8.1.12.1.3 | Integer32 | read-create | This object indicates the number of 1DM frames to be sent. In a proactive OAM scenario, the value is 0. |
| I32 hwY1731TestIdOneWayDMSendPacketSize | 1.3.6.1.4.1.2011.5.25.136.1.8.1.12.1.4 | Integer32 | read-create | This object indicates the size of a one-way ETH-DM packet. The value 0 means that the packet size is not specified. By default, the value is 0. |
| ROW hwY1731TestIdOneWayDMSendRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.12.1.99 | RowStatus | read-create | This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated. |
| hwY1731TestIdOneWayDMReceiveTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.13 | not-accessible | This table configures the one-way ETH-DM receiving function. | |
| hwY1731TestIdOneWayDMReceiveEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.13.1 | not-accessible | The configuration entry of one-way ETH-DM receiving function. | |
| T/F hwY1731TestIdOneWayDMReceiveIsContinue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.13.1.1 | TruthValue | read-create | This object indicates whether one-way ETH-DM receiving is continual. If the value is 'false', it indicates that one-way ETH-DM is on-demand. |
| ROW hwY1731TestIdOneWayDMReceiveRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.13.1.99 | RowStatus | read-create | This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated. |
| hwY1731TestIdTwoWayDMSendTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.14 | not-accessible | This table is used to configure the two-way ETH-DM sending function. | |
| hwY1731TestIdTwoWayDMSendEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.14.1 | not-accessible | The configuration entry of the two-way ETH-DM sending function. | |
| T/F hwY1731TestIdTwoWayDMSendIsContinue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.14.1.1 | TruthValue | read-create | This object indicates whether two-way ETH-DM sending is continual. If the value is 'false', it indicates that two-way ETH-DM is on-demand. |
| INT hwY1731TestIdTwoWayDMSendInterval | 1.3.6.1.4.1.2011.5.25.136.1.8.1.14.1.2 | INTEGER | read-create | This object indicates the interval at which DMM frames are sent. When on-demand OAM, the value can be: 1 second 10 seconds 30 seconds 60 seconds |
| I32 hwY1731TestIdTwoWayDMSendCount | 1.3.6.1.4.1.2011.5.25.136.1.8.1.14.1.3 | Integer32 | read-create | This object indicates the number of DMM frames to be sent. In a proactive OAM scenario, the value is 0. |
| I32 hwY1731TestIdTwoWayDMSendPacketSize | 1.3.6.1.4.1.2011.5.25.136.1.8.1.14.1.4 | Integer32 | read-create | This object indicates the size of two-way ETH-DM packet. The value 0 means that the packet size is not specified. By default, the value is 0. |
| ROW hwY1731TestIdTwoWayDMSendRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.14.1.99 | RowStatus | read-create | This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated. |
| hwY1731TestIdTwoWayDMReceiveTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.15 | not-accessible | This table configures the two-way ETH-DM receiving function. | |
| hwY1731TestIdTwoWayDMReceiveEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.15.1 | not-accessible | The configuration entry of the two-way ETH-DM receiving function. | |
| ROW hwY1731TestIdTwoWayDMReceiveRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.15.1.99 | RowStatus | read-create | This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated. |
| hwY1731TestIdSingleSynEndedLMSendTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.16 | not-accessible | This table configures the single-ended ETH-SLM sending function. | |
| hwY1731TestIdSingleSynEndedLMSendEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.16.1 | not-accessible | The configuration entry of the single-ended ETH-SLM sending function. | |
| T/F hwY1731TestIdSingleSynEndedLMSendIsContinue | 1.3.6.1.4.1.2011.5.25.136.1.8.1.16.1.1 | TruthValue | read-create | This object indicates whether single-ended ETH-SLM sending is continual. If the value is 'false', it indicates that the single-ended ETH-SLM is on-demand. |
| INT hwY1731TestIdSingleSynEndedLMSendInterval | 1.3.6.1.4.1.2011.5.25.136.1.8.1.16.1.2 | INTEGER | read-create | This object indicates the interval at which single-ended ETH-SLM frames are sent. the value can be: 1 second 10 seconds 3.3 milliseconds 10 milliseconds 100 milliseconds |
| I32 hwY1731TestIdSingleSynEndedLMSendCount | 1.3.6.1.4.1.2011.5.25.136.1.8.1.16.1.3 | Integer32 | read-create | This object indicates the number of the sent single-ended ETH-SLM frames. The value can be 0 or ranges from 1 to 1000. In a proactive OAM scenario, the value is 0. |
| I32 hwY1731TestIdSingleSynEndedLMSendTimeOut | 1.3.6.1.4.1.2011.5.25.136.1.8.1.16.1.4 | Integer32 | read-create | This object indicates The timeout of single-ended synthetic loss measurement frames (SLM) waiting for ACK frames (SLR). The value can be 0 or ranges from 1 to 10. In a proactive OAM scenario, the value is 0. |
| ROW hwY1731TestIdSingleSynEndedLMSendRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.16.1.5 | RowStatus | read-create | This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated. |
| hwY1731TestIdSingleSynEndedLMReceiveTable | 1.3.6.1.4.1.2011.5.25.136.1.8.1.17 | not-accessible | This table configures the single-ended ETH-SLM receive function. | |
| hwY1731TestIdSingleSynEndedLMReceiveEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.1.17.1 | not-accessible | The configuration entry of the single-ended ETH-SLM receive function. | |
| I32 hwY1731TestIdSingleSynEndedLMReceiveTimeOut | 1.3.6.1.4.1.2011.5.25.136.1.8.1.17.1.1 | Integer32 | read-create | This object indicates the timeout value of receive ETH-SLM frames. The value can be 0 or ranges from 10 to 300. In a proactive OAM scenario, the value is 0. |
| ROW hwY1731TestIdSingleSynEndedLMReceiveRowStatus | 1.3.6.1.4.1.2011.5.25.136.1.8.1.17.1.2 | RowStatus | read-create | This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated. |
| hwY1731StatisticObject | 1.3.6.1.4.1.2011.5.25.136.1.8.2 | |||
| hwY1731ResetStatisticTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.1 | not-accessible | This table is used to reset statistic information. | |
| hwY1731ResetStatisticEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.1.1 | not-accessible | The entry of reset statistic information. | |
| INT hwY1731ResetStatisticType | 1.3.6.1.4.1.2011.5.25.136.1.8.2.1.1.1 | INTEGER | read-write | This object indicates the type of reset. The value can be: invalid singleloss dualloss onewaydelay twowaydelay The default value is invalid. |
| I32 hwY1731ResetStatistic8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.2.1.1.2 | Integer32 | read-write | This object indicates the priority of 802.1p which in the ResetStatistic. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set. |
| hwY1731StatisticTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2 | not-accessible | This table is used to store the result about Y1731 statistic information. | |
| hwY1731StatisticEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1 | not-accessible | An entry in the table, containing information on the Y1731 statistic entity. | |
| INT hwY1731SingleLossStatisticGatherInterval | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.1 | INTEGER | read-only | This object identifies an interval for collecting packet loss statistics. |
| OCT hwY1731SingleLossLocalStatistic | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.2 | OCTET STRING | read-only | This object identifies the packet loss statistics that are collected on a local end. |
| OCT hwY1731SingleLossLocalRatio | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.3 | OCTET STRING | read-only | This object identifies the packet loss ratio that are collected on a local end. |
| I32 hwY1731SingleLossLocalRatioMax | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.4 | Integer32 | read-only | This object identifies the maximum value of packet loss ratio that are collected on a local end. |
| I32 hwY1731SingleLossLocalRatioMin | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.5 | Integer32 | read-only | This object identifies the minimum value of packet loss ratio that are collected on a local end. |
| I32 hwY1731SingleLossLocalRatioAvg | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.6 | Integer32 | read-only | This object identifies the average value of packet loss ratio that are collected on a local end. |
| OCT hwY1731SingleLossRemoteStatistic | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.7 | OCTET STRING | read-only | This object identifies the packet loss statistics that are collected on a remote end. |
| OCT hwY1731SingleLossRemoteRatio | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.8 | OCTET STRING | read-only | This object identifies the packet loss ratio that are collected on a remote end. |
| I32 hwY1731SingleLossRemoteRatioMax | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.9 | Integer32 | read-only | This object identifies the maximum value of packet loss ratio that are collected on a remote end. |
| I32 hwY1731SingleLossRemoteRatioMin | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.10 | Integer32 | read-only | This object identifies the minimum value of packet loss ratio that are collected on a remote end. |
| I32 hwY1731SingleLossRemoteRatioAvg | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.11 | Integer32 | read-only | This object identifies the average value of packet loss ratio that are collected on a remote end. |
| OCT hwY1731OneDelayStatistic | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.12 | OCTET STRING | read-only | This object indicates the statistics about the one-way delay. |
| OCT hwY1731OneDelayVariation | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.13 | OCTET STRING | read-only | This object indicates the variation about the one-way delay. After the device is enabled to receive packets, statistics collected for the first time are invalid, and the value of hwY1731OneDelayVariation is setted to 0. |
| U32 hwY1731OneDelayMax | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.14 | Unsigned32 | read-only | This object identifies the maximum variation of the one-way delay. |
| U32 hwY1731OneDelayMin | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.15 | Unsigned32 | read-only | This object identifies the minimum variation of the one-way delay. |
| U32 hwY1731OneDelayAvg | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.16 | Unsigned32 | read-only | This object identifies the average variation of the one-way delay. |
| OCT hwY1731TwoDelayStatistic | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.17 | OCTET STRING | read-only | This object indicates the statistics about the two-way delay. |
| OCT hwY1731TwoDelayVariation | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.18 | OCTET STRING | read-only | This object indicates the variation about the two-way delay. |
| U32 hwY1731TwoDelayMax | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.19 | Unsigned32 | read-only | This object identifies the maximum variation of the two-way delay. |
| U32 hwY1731TwoDelayMin | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.20 | Unsigned32 | read-only | This object identifies the minimum variation of the two-way delay. |
| U32 hwY1731TwoDelayAvg | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.21 | Unsigned32 | read-only | This object identifies the average variation of the two-way delay. |
| U32 hwY1731SingleLossLocalMax | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.22 | Unsigned32 | read-only | This object identifies the maximum value of packet loss that are collected on a local end. |
| U32 hwY1731SingleLossLocalMin | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.23 | Unsigned32 | read-only | This object identifies the minimum value of packet loss that are collected on a local end. |
| U32 hwY1731SingleLossLocalAvg | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.24 | Unsigned32 | read-only | This object identifies the average value of packet loss that are collected on a local end. |
| U32 hwY1731SingleLossRemoteMax | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.25 | Unsigned32 | read-only | This object identifies the maximum value of packet loss that are collected on a remote end. |
| U32 hwY1731SingleLossRemoteMin | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.26 | Unsigned32 | read-only | This object identifies the minimum value of packet loss that are collected on a remote end. |
| U32 hwY1731SingleLossRemoteAvg | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.27 | Unsigned32 | read-only | This object identifies the average value of packet loss that are collected on a remote end. |
| I32 hwY1731OneDelayStatisticMax | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.28 | Integer32 | read-only | This object identifies the maximum value of the one-way delay. |
| I32 hwY1731OneDelayStatisticMin | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.29 | Integer32 | read-only | This object identifies the minimum value of the one-way delay. |
| I32 hwY1731OneDelayStatisticAvg | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.30 | Integer32 | read-only | This object identifies the average value of the one-way delay. |
| U32 hwY1731TwoDelayStatisticMax | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.31 | Unsigned32 | read-only | This object identifies the maximum value of the two-way delay. |
| U32 hwY1731TwoDelayStatisticMin | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.32 | Unsigned32 | read-only | This object identifies the minimum value of the two-way delay. |
| U32 hwY1731TwoDelayStatisticAvg | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.33 | Unsigned32 | read-only | This object identifies the average value of the two-way delay. |
| U32 hwY1731TwoDelayUnresponsivePacketCount | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.34 | Unsigned32 | read-only | This object identifies the number of unresponsive Delay Measurement Reply frames. |
| I32 hwY1731SingleLossStatistic8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.35 | Integer32 | read-only | This object indicates the 802.1p priority. The value 255 is an invalid value. |
| I32 hwY1731OneDelayStatistic8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.36 | Integer32 | read-only | This object indicates the 802.1p priority. The value 255 is an invalid value. |
| I32 hwY1731TwoDelayStatistic8021pValue | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.37 | Integer32 | read-only | This object indicates the 802.1p priority. The value 255 is an invalid value. |
| DAT hwY1731OneDelayOnDemandStartTime | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.38 | DateAndTime | read-only | The date and time of the one-way delay on-demand data. |
| DAT hwY1731TwoDelayOnDemandStartTime | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.39 | DateAndTime | read-only | The date and time of the two-way delay on-demand data. |
| DAT hwY1731SingleLossOnDemandStartTime | 1.3.6.1.4.1.2011.5.25.136.1.8.2.2.1.40 | DateAndTime | read-only | The date and time of the single-loss on-demand data. |
| hwCfmVlanOneDelayTrapLogTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.3 | not-accessible | This table is used to query whether the one-way delay exceeds the trap threshold in the VLAN scenario. | |
| hwCfmVlanOneDelayTrapLogEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.3.1 | not-accessible | An entry in the table, containing information on the trap entity. | |
| MAC hwCfmOneDelayTrapLogMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.2.3.1.1 | MacAddress | accessible-for-notify | This object indicates the remote MAC address. |
| TIM hwCfmVlanOneDelayTrapLogTimestamp | 1.3.6.1.4.1.2011.5.25.136.1.8.2.3.1.2 | TimeStamp | accessible-for-notify | This object indicates the timestamp when the delay of the one-way ETH-DM in the VLAN is higher than the configured trap threshold. |
| U32 hwCfmVlanOneDelayTrapLogDelayValue | 1.3.6.1.4.1.2011.5.25.136.1.8.2.3.1.3 | Unsigned32 | accessible-for-notify | This object indicates the delay value when the delay of the one-way ETH-DM in the VLAN is higher than the configured trap threshold. |
| U32 hwCfmVlanOneDelayTrapLogThreshold | 1.3.6.1.4.1.2011.5.25.136.1.8.2.3.1.4 | Unsigned32 | accessible-for-notify | This object indicates the delay trap threshold of the one-way ETH-DM. |
| U32 hwCfmVlanOneDelayTrapLogDelayValueHigh | 1.3.6.1.4.1.2011.5.25.136.1.8.2.3.1.5 | Unsigned32 | accessible-for-notify | This object indicates the high 32 bits delay value when the delay of the one-way ETH-DM in the VLAN is higher than the configured trap threshold. |
| U32 hwCfmVlanOneDelayTrapLogDelayValueLow | 1.3.6.1.4.1.2011.5.25.136.1.8.2.3.1.6 | Unsigned32 | accessible-for-notify | This object indicates the low 32 bits delay value when the delay of the one-way ETH-DM in the VLAN is higher than the configured trap threshold. |
| hwCfmVlanOneDelayRcoverTrapLogTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.4 | not-accessible | This table is used to query whether the one-way delay falls below the trap threshold. | |
| hwCfmVlanOneDelayRcoverTrapLogEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.4.1 | not-accessible | An entry in the table, containing information on the recovery trap entity. | |
| MAC hwCfmOneDelayRecoveryTrapMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.2.4.1.1 | MacAddress | accessible-for-notify | This object indicates the remote MAC address. |
| TIM hwCfmVlanOneDelayRecoveryTrapLogTimestamp | 1.3.6.1.4.1.2011.5.25.136.1.8.2.4.1.2 | TimeStamp | accessible-for-notify | This object indicates the timestamp when the delay of the one-way ETH-DM in the VLAN is lower than the configured trap threshold. |
| U32 hwCfmVlanOneDelayRecoveryTrapLogDelayValue | 1.3.6.1.4.1.2011.5.25.136.1.8.2.4.1.3 | Unsigned32 | accessible-for-notify | This object indicates the delay value when the delay of the one-way ETH-DM in the VLAN is lower than the configured trap threshold. |
| U32 hwCfmVlanOneDelayRecoveryTrapLogThreshold | 1.3.6.1.4.1.2011.5.25.136.1.8.2.4.1.4 | Unsigned32 | accessible-for-notify | This object indicates the delay trap threshold of the one-way ETH-DM. |
| U32 hwCfmVlanOneDelayRecoveryTrapLogDelayValueHigh | 1.3.6.1.4.1.2011.5.25.136.1.8.2.4.1.5 | Unsigned32 | accessible-for-notify | This object indicates the high 32 bits delay value when the delay of the one-way ETH-DM in the VLAN is lower than the configured trap threshold. |
| U32 hwCfmVlanOneDelayRecoveryTrapLogDelayValueLow | 1.3.6.1.4.1.2011.5.25.136.1.8.2.4.1.6 | Unsigned32 | accessible-for-notify | This object indicates the low 32 bits delay value when the delay of the one-way ETH-DM in the VLAN is lower than the configured trap threshold. |
| hwCfmVlanTwoDelayTrapLogTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.5 | not-accessible | This table is used to query whether the two-way delay exceeds the trap threshold in the VLAN scenario. | |
| hwCfmVlanTwoDelayTrapLogEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.5.1 | not-accessible | An entry in the table, containing information on the trap entity. | |
| MAC hwCfmTwoDelayTrapMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.2.5.1.1 | MacAddress | accessible-for-notify | This object indicates the remote MAC address. |
| TIM hwCfmVlanTwoDelayTrapLogTimestamp | 1.3.6.1.4.1.2011.5.25.136.1.8.2.5.1.2 | TimeStamp | accessible-for-notify | This object indicates the timestamp when the delay of the two-way ETH-DM in the VLAN is higher than the configured trap threshold. |
| U32 hwCfmVlanTwoDelayTrapLogDelayValue | 1.3.6.1.4.1.2011.5.25.136.1.8.2.5.1.3 | Unsigned32 | accessible-for-notify | This object indicates the delay value when the delay of the two-way ETH-DM in the VLAN is higher than the configured trap threshold. |
| U32 hwCfmVlanTwoDelayTrapLogThreshold | 1.3.6.1.4.1.2011.5.25.136.1.8.2.5.1.4 | Unsigned32 | accessible-for-notify | This object indicates the delay trap threshold of the two-way ETH-DM. |
| U32 hwCfmVlanTwoDelayTrapLogDelayValueHigh | 1.3.6.1.4.1.2011.5.25.136.1.8.2.5.1.5 | Unsigned32 | accessible-for-notify | This object indicates the high 32 bits delay value when the delay of the two-way ETH-DM in the VLAN is higher than the configured trap threshold. |
| U32 hwCfmVlanTwoDelayTrapLogDelayValueLow | 1.3.6.1.4.1.2011.5.25.136.1.8.2.5.1.6 | Unsigned32 | accessible-for-notify | This object indicates the low 32 bits delay value when the delay of the two-way ETH-DM in the VLAN is higher than the configured trap threshold. |
| hwCfmVlanTwoDelayRcoverTrapLogTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.6 | not-accessible | This table is used to query whether the two-way delay falls below the trap threshold. | |
| hwCfmVlanTwoDelayRcoverTrapLogEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.6.1 | not-accessible | An entry in the table, containing information on the recovery trap entity. | |
| MAC hwCfmTwoDelayRecoveryTrapMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.2.6.1.1 | MacAddress | accessible-for-notify | This object indicates the remote MAC address. |
| TIM hwCfmVlanTwoDelayRecoveryTrapLogTimestamp | 1.3.6.1.4.1.2011.5.25.136.1.8.2.6.1.2 | TimeStamp | accessible-for-notify | This object indicates the timestamp when the delay of the two-way ETH-DM in the VLAN is lower than the configured trap threshold. |
| U32 hwCfmVlanTwoDelayRecoveryTrapLogDelayValue | 1.3.6.1.4.1.2011.5.25.136.1.8.2.6.1.3 | Unsigned32 | accessible-for-notify | This object indicates the delay value when the delay of the two-way ETH-DM in the VLAN is lower than the configured trap threshold. |
| U32 hwCfmVlanTwoDelayRecoveryTrapLogThreshold | 1.3.6.1.4.1.2011.5.25.136.1.8.2.6.1.4 | Unsigned32 | accessible-for-notify | This object indicates the delay trap threshold for the two-way ETH-DM. |
| U32 hwCfmVlanTwoDelayRecoveryTrapLogDelayValueHigh | 1.3.6.1.4.1.2011.5.25.136.1.8.2.6.1.5 | Unsigned32 | accessible-for-notify | This object indicates the high 32 bits delay value when the delay of the two-way ETH-DM in the VLAN is lower than the configured trap threshold. |
| U32 hwCfmVlanTwoDelayRecoveryTrapLogDelayValueLow | 1.3.6.1.4.1.2011.5.25.136.1.8.2.6.1.6 | Unsigned32 | accessible-for-notify | This object indicates the low 32 bits delay value when the delay of the two-way ETH-DM in the VLAN is lower than the configured trap threshold. |
| hwY1731StatisticTrapLogTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.7 | not-accessible | This table is used to query whether the Y.1731 statistic value triggers alarm. | |
| hwY1731StatisticTrapLogEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.7.1 | not-accessible | An entry in the table, containing information on the statistic trap entity. | |
| INT hwY1731StatisticTrapLogType | 1.3.6.1.4.1.2011.5.25.136.1.8.2.7.1.1 | INTEGER | accessible-for-notify | Specific trap type. Options: 1. OneDelay(1) -indicates the trap type is delay of one-way ETH-DM. 2. TwoDelay(2) -indicates the trap type is delay of two-way ETH-DM. 3. OneDelayVariation(3) -indicates the trap type is delay variation of one-way ETH-DM. 4. TweDelayVariation(4) -indicates the trap type is delay variation of two-way ETH-DM. 5. SingleLossLocalRatio(5) -indicates the trap type is local loss ratio of single-ended ETH-LM. 6. SingleLossRemoteRatio(6) -indicates the trap type is remote loss ratio of single-ended ETH-LM. 7. DualLossLocalRatio(7) -indicates the trap type is local loss ratio of dual-ended ETH-LM. 8. DualLossRemoteRatio(8) -indicates the trap type is remote loss ratio of dual-ended ETH-LM. |
| MAC hwY1731StatisticTrapLogMacAddress | 1.3.6.1.4.1.2011.5.25.136.1.8.2.7.1.2 | MacAddress | accessible-for-notify | This object indicates the remote MAC address. |
| I32 hwY1731StatisticTrapLog8021pPriority | 1.3.6.1.4.1.2011.5.25.136.1.8.2.7.1.3 | Integer32 | accessible-for-notify | This object indicates the priority. The value can be 255 or ranges from 0 to 7. The value 255 is an invalid value. |
| U32 hwY1731StatisticTrapLogValue | 1.3.6.1.4.1.2011.5.25.136.1.8.2.7.1.4 | Unsigned32 | accessible-for-notify | The value that cause the trap. |
| U32 hwY1731StatisticTrapLogUpperLimitThreshold | 1.3.6.1.4.1.2011.5.25.136.1.8.2.7.1.5 | Unsigned32 | accessible-for-notify | The upper limit value of the threshold. |
| U32 hwY1731StatisticTrapLogLowerLimitThreshold | 1.3.6.1.4.1.2011.5.25.136.1.8.2.7.1.6 | Unsigned32 | accessible-for-notify | The lower limit value of the threshold. |
| U32 hwY1731StatisticTrapLogValueHigh | 1.3.6.1.4.1.2011.5.25.136.1.8.2.7.1.7 | Unsigned32 | accessible-for-notify | The value that cause the trap. |
| U32 hwY1731StatisticTrapLogValueLow | 1.3.6.1.4.1.2011.5.25.136.1.8.2.7.1.8 | Unsigned32 | accessible-for-notify | The value that cause the trap. |
| hwY1731TestIdSingleLossStatTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.8 | not-accessible | This table stores the result of single-ended ETH-LM. | |
| hwY1731TestIdSingleLossStatEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.8.1 | not-accessible | An entry in the table, containing information about the result of single-ended ETH-LM. | |
| U32 hwY1731TestIdSingleLossSequence | 1.3.6.1.4.1.2011.5.25.136.1.8.2.8.1.1 | Unsigned32 | read-only | This object indicates the sequence number of the single-ended ETH-LM result. |
| U32 hwY1731TestIdSingleLossErrInfo | 1.3.6.1.4.1.2011.5.25.136.1.8.2.8.1.2 | Unsigned32 | read-only | This object indicates the error information of the single-ended ETH-LM result. |
| C64 hwY1731TestIdSingleLossLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.8.1.3 | Counter64 | read-only | This object identifies the packet loss statistics that are collected on a local end. |
| U32 hwY1731TestIdSingleLossLocalRatio | 1.3.6.1.4.1.2011.5.25.136.1.8.2.8.1.4 | Unsigned32 | read-only | This object identifies the packet loss ratio that is collected on a local end. |
| C64 hwY1731TestIdSingleLossRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.8.1.5 | Counter64 | read-only | This object identifies the packet loss statistics that are collected on a remote end. |
| U32 hwY1731TestIdSingleLossRemoteRatio | 1.3.6.1.4.1.2011.5.25.136.1.8.2.8.1.6 | Unsigned32 | read-only | This object identifies the packet loss ratio that is collected on a remote end. |
| DAT hwY1731TestIdSingleLossOnDemandStartTime | 1.3.6.1.4.1.2011.5.25.136.1.8.2.8.1.7 | DateAndTime | read-only | The date and time of the single-loss on-demand data. |
| hwY1731TestIdOneDelayStatTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.9 | not-accessible | This table stores the result of one-way ETH-DM. | |
| hwY1731TestIdOneDelayStatEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.9.1 | not-accessible | An entry in the table, containing information about the result of one-way ETH-DM. | |
| U32 hwY1731TestIdOneDelaySequence | 1.3.6.1.4.1.2011.5.25.136.1.8.2.9.1.1 | Unsigned32 | read-only | This object indicates the sequence number of the one-way ETH-DM result. |
| U32 hwY1731TestIdOneDelayErrInfo | 1.3.6.1.4.1.2011.5.25.136.1.8.2.9.1.2 | Unsigned32 | read-only | This object indicates the error information about the one-way delay. |
| I32 hwY1731TestIdOneDelay | 1.3.6.1.4.1.2011.5.25.136.1.8.2.9.1.3 | Integer32 | read-only | This object indicates the statistics about the one-way delay. |
| U32 hwY1731TestIdOneDelayVariation | 1.3.6.1.4.1.2011.5.25.136.1.8.2.9.1.4 | Unsigned32 | read-only | This object indicates the variation about the one-way delay. After the device is enabled to receive packets, statistics collected for the first time are invalid, and the value is set to 0. |
| DAT hwY1731TestIdOneDelayOnDemandStartTime | 1.3.6.1.4.1.2011.5.25.136.1.8.2.9.1.5 | DateAndTime | read-only | The date and time of the one-way delay on-demand data. |
| hwY1731TestIdTwoDelayStatTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.10 | not-accessible | This table stores the result of two-way ETH-DM. | |
| hwY1731TestIdTwoDelayStatEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.10.1 | not-accessible | An entry in the table, containing information about the result of two-way ETH-DM. | |
| U32 hwY1731TestIdTwoDelaySequence | 1.3.6.1.4.1.2011.5.25.136.1.8.2.10.1.1 | Unsigned32 | read-only | This object indicates the sequence number of the two-way ETH-DM result. |
| U32 hwY1731TestIdTwoDelayErrInfo | 1.3.6.1.4.1.2011.5.25.136.1.8.2.10.1.2 | Unsigned32 | read-only | This object indicates the error information of the two-way ETH-DM result. |
| U32 hwY1731TestIdTwoDelay | 1.3.6.1.4.1.2011.5.25.136.1.8.2.10.1.3 | Unsigned32 | read-only | This object indicates the statistics about the two-way delay. |
| U32 hwY1731TestIdTwoDelayVariation | 1.3.6.1.4.1.2011.5.25.136.1.8.2.10.1.4 | Unsigned32 | read-only | This object indicates the variation about the two-way delay. After the device is enabled to receive packets, statistics collected for the first time are invalid, and the value is set to 0. |
| DAT hwY1731TestIdTwoDelayOnDemandStartTime | 1.3.6.1.4.1.2011.5.25.136.1.8.2.10.1.5 | DateAndTime | read-only | The date and time of the two-way delay on-demand data. |
| hwY1731TestIdStatisticResetTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.11 | not-accessible | This table stores the result of two-way ETH-DM. | |
| hwY1731TestIdStatisticResetEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.11.1 | not-accessible | An entry in the table, containing information about the result of two-way ETH-DM. | |
| INT hwY1731TestIdResetStatisticType | 1.3.6.1.4.1.2011.5.25.136.1.8.2.11.1.1 | INTEGER | read-write | This object indicates the type of reset. The value can be: invalid singleloss dualloss onewaydelay twowaydelay singlesynloss The default value is invalid. |
| hwY1731TestIdTwoDelaySummaryStatTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12 | not-accessible | This table stores the statistics of two-way ETH-DM collected during the last period. | |
| hwY1731TestIdTwoDelaySummaryStatEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1 | not-accessible | An entry in the table, containing information about the statistics of two-way ETH-DM collected during the last period. | |
| U32 hwY1731TestIdTwoDelayIndex | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.1 | Unsigned32 | not-accessible | This object indicates the sequence of the last period. |
| U32 hwY1731TestIdTwoDelayNbrSamples | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.2 | Unsigned32 | read-only | This object indicates the sample number of the two-way delay during the last period. |
| U32 hwY1731TestIdTwoDelayMax | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.3 | Unsigned32 | read-only | This object indicates the maximum value of the two-way delay collected during the last period. |
| U32 hwY1731TestIdTwoDelayMin | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.4 | Unsigned32 | read-only | This object indicates the minimum value of the two-way delay collected during the last period. |
| U32 hwY1731TestIdTwoDelayAve | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.5 | Unsigned32 | read-only | This object indicates the average value of the two-way delay collected during the last period. |
| U32 hwY1731TestIdTwoDelayExceedUpLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.6 | Unsigned32 | read-only | This object indicates the num of two-way delay samples exceeded the upper limit value of the threshold during the last period. |
| U32 hwY1731TestIdTwoDelayBelowLowLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.7 | Unsigned32 | read-only | This object indicates the num of two-way delay samples fell below lower limit value of the threshold during the last period. |
| U32 hwY1731TestIdTwoDelayVariationNbrSamples | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.8 | Unsigned32 | read-only | This object indicates the sample number of the two-way delay variation during the last period. |
| U32 hwY1731TestIdTwoDelayVariationMax | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.9 | Unsigned32 | read-only | This object indicates the maximum variation of the two-way delay variation collected during the last period. |
| U32 hwY1731TestIdTwoDelayVariationMin | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.10 | Unsigned32 | read-only | This object indicates the minimum variation of the two-way delay variation collected during the last period. |
| U32 hwY1731TestIdTwoDelayVariationAve | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.11 | Unsigned32 | read-only | This object indicates the average variation of the two-way delay variation collected during the last period. |
| U32 hwY1731TestIdTwoDelayVarExceedUpLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.12 | Unsigned32 | read-only | This object indicates the num of two-way delay variation samples exceeded the upper limit value of the threshold during the last period. |
| U32 hwY1731TestIdTwoDelayVarBelowLowLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.12.1.13 | Unsigned32 | read-only | This object indicates the num of two-way delay variation samples fell below lower limit value of the threshold during the last period. |
| hwY1731TestIdSingleSynLossSummaryStatTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13 | not-accessible | This table stores the statistics of single-ended ETH-SLM collected during the last period. | |
| hwY1731TestIdSingleSynLossSummaryStatEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1 | not-accessible | An entry in the table, containing information about the statistics of single-ended ETH-SLM collected during the last period. | |
| U32 hwY1731TestIdSingleSynLossIndex | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.1 | Unsigned32 | not-accessible | This object indicates the sequence of the last period. |
| U32 hwY1731TestIdSingleSynLossNbrSamples | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.2 | Unsigned32 | read-only | This object indicates the sample number of the single-ended ETH-SLM result during the last period. |
| U32 hwY1731TestIdSingleSynSendRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.3 | Unsigned32 | read-only | This object indicates the packet send statistics that are collected on a remote end during the last period. |
| U32 hwY1731TestIdSingleSynRecvLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.4 | Unsigned32 | read-only | This object indicates the packet receive statistics that are collected on a local end during the last period. |
| I32 hwY1731TestIdSingleSynLossLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.5 | Integer32 | read-only | This object indicates the packet loss statistics that are collected on a local end during the last period. |
| U32 hwY1731TestIdSingleSynExceedLocalUpLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.6 | Unsigned32 | read-only | This object indicates the number of local loss ratio samples exceeded the upper limit value of the threshold during the last period. |
| U32 hwY1731TestIdSingleSynBelowLocalLowLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.7 | Unsigned32 | read-only | This object indicates the number of local loss ratio samples fell below lower limit value of the threshold during the last period. |
| U32 hwY1731TestIdSingleSynSendLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.8 | Unsigned32 | read-only | This object indicates the packet send statistics that are collected on a local end during the last period. |
| U32 hwY1731TestIdSingleSynRecvRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.9 | Unsigned32 | read-only | This object indicates the packet receive statistics that are collected on a remote end during the last period. |
| I32 hwY1731TestIdSingleSynLossRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.10 | Integer32 | read-only | This object indicates the packet loss statistics that are collected on a remote end during the last period. |
| U32 hwY1731TestIdSingleSynExceedRemoteUpLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.11 | Unsigned32 | read-only | This object indicates the number of remote loss ratio samples exceeded the upper limit value of the threshold during the last period. |
| U32 hwY1731TestIdSingleSynBelowRemoteLowLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.13.1.12 | Unsigned32 | read-only | This object indicates the number of remote loss ratio samples fell below lower limit value of the threshold during the last period. |
| hwY1731SingleLossSummaryStatTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14 | not-accessible | This table stores the statistics of single-ended ETH-LM collected during the last period. | |
| hwY1731SingleLossSummaryStatEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1 | not-accessible | An entry in the table, containing information about the statistics of single-ended ETH-LM collected during the last period. | |
| U32 hwY1731SingleLossIndex | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.1 | Unsigned32 | not-accessible | This object indicates the sequence of the last period. |
| U32 hwY1731SingleLossNbrSamples | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.2 | Unsigned32 | read-only | This object indicates the sample number of the single-ended ETH-SLM result during the last period. |
| C64 hwY1731SingleLossSendRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.3 | Counter64 | read-only | This object indicates the packet send statistics that are collected on a remote end during the last period. |
| C64 hwY1731SingleLossRecvLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.4 | Counter64 | read-only | This object indicates the packet receive statistics that are collected on a local end during the last period. |
| C64 hwY1731SingleLossLossLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.5 | Counter64 | read-only | This object indicates the packet loss statistics that are collected on a local end during the last period. |
| U32 hwY1731SingleLossExceedLocalUpLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.6 | Unsigned32 | read-only | This object indicates the number of local loss ratio samples exceeded the upper limit value of the threshold during the last period. |
| U32 hwY1731SingleLossBelowLocallowLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.7 | Unsigned32 | read-only | This object indicates the number of local loss ratio samples fell below lower limit value of the threshold during the last period. |
| C64 hwY1731SingleLossSendLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.8 | Counter64 | read-only | This object indicates the packet send statistics that are collected on a local end during the last period. |
| C64 hwY1731SingleLossRecvRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.9 | Counter64 | read-only | This object indicates the packet receive statistics that are collected on a remote end during the last period. |
| C64 hwY1731SingleLossLossRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.10 | Counter64 | read-only | This object indicates the packet loss statistics that are collected on a remote end during the last period. |
| U32 hwY1731SingleLossExceedRemoteUpLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.11 | Unsigned32 | read-only | This object indicates the number of remote loss ratio samples exceeded the upper limit value of the threshold during the last period. |
| U32 hwY1731SingleLossBelowRemotelowLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.14.1.12 | Unsigned32 | read-only | This object indicates the number of remote loss ratio samples fell below lower limit value of the threshold during the last period. |
| hwY1731TestIdSingleLossSummaryStatTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15 | not-accessible | This table stores the statistics of single-ended ETH-LM collected during the last period with testid. | |
| hwY1731TestIdSingleLossSummaryStatEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1 | not-accessible | An entry in the table, containing information about the statistics of single-ended ETH-LM collected during the last period with testid. | |
| U32 hwY1731TestIdSingleLossIndex | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.1 | Unsigned32 | not-accessible | This object indicates the sequence of the last period. |
| U32 hwY1731TestIdSingleLossNbrSamples | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.2 | Unsigned32 | read-only | This object indicates the sample number of the single-ended ETH-SLM result during the last period. |
| C64 hwY1731TestIdSingleLossSendRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.3 | Counter64 | read-only | This object indicates the packet send statistics that are collected on a remote end during the last period. |
| C64 hwY1731TestIdSingleLossRecvLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.4 | Counter64 | read-only | This object indicates the packet receive statistics that are collected on a local end during the last period. |
| C64 hwY1731TestIdSingleLossLossLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.5 | Counter64 | read-only | This object indicates the packet loss statistics that are collected on a local end during the last period. |
| U32 hwY1731TestIdSingleLossExceedLocalUpLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.6 | Unsigned32 | read-only | This object indicates the number of local loss ratio samples exceeded the upper limit value of the threshold during the last period. |
| U32 hwY1731TestIdSingleLossBelowLocallowLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.7 | Unsigned32 | read-only | This object indicates the number of local loss ratio samples fell below lower limit value of the threshold during the last period. |
| C64 hwY1731TestIdSingleLossSendLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.8 | Counter64 | read-only | This object indicates the packet send statistics that are collected on a local end during the last period. |
| C64 hwY1731TestIdSingleLossRecvRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.9 | Counter64 | read-only | This object indicates the packet receive statistics that are collected on a remote end during the last period. |
| C64 hwY1731TestIdSingleLossLossRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.10 | Counter64 | read-only | This object indicates the packet loss statistics that are collected on a remote end during the last period. |
| U32 hwY1731TestIdSingleLossExceedRemoteUpLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.11 | Unsigned32 | read-only | This object indicates the number of remote loss ratio samples exceeded the upper limit value of the threshold during the last period. |
| U32 hwY1731TestIdSingleLossBelowRemotelowLimitNum | 1.3.6.1.4.1.2011.5.25.136.1.8.2.15.1.12 | Unsigned32 | read-only | This object indicates the number of remote loss ratio samples fell below lower limit value of the threshold during the last period. |
| hwY1731TestIdSingleSynLossStatTable | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16 | not-accessible | This table stores the result of single-ended ETH-SLM. | |
| hwY1731TestIdSingleSynLossStatEntry | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1 | not-accessible | An entry in the table, containing information about the result of single-ended ETH-SLM. | |
| U32 hwY1731TestIdSingleSynLossSequence | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.1 | Unsigned32 | not-accessible | This object indicates the sequence number of the single-ended ETH-SLM result. |
| U32 hwY1731TestIdSingleSynLossErrInfo | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.2 | Unsigned32 | read-only | This object indicates the error information of the single-ended ETH-SLM result. |
| U32 hwY1731TestIdSingleSynLossLocalSend | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.3 | Unsigned32 | read-only | This object indicates the number of local send packets about single-synthetic frame loss. |
| U32 hwY1731TestIdSingleSynLossRemoteSend | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.4 | Unsigned32 | read-only | This object indicates the number of remote send packets about single-synthetic frame loss. |
| U32 hwY1731TestIdSingleSynLossLocalReceive | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.5 | Unsigned32 | read-only | This object indicates the number of local receive packets about single-synthetic frame loss |
| U32 hwY1731TestIdSingleSynLossUnack | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.6 | Unsigned32 | read-only | This object indicates the number of local unanswered packets about single-synthetic frame loss. |
| I32 hwY1731TestIdSingleSynLossLossLocal | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.7 | Integer32 | read-only | This object identifies the packet loss statistics that are collected on a local end. |
| U32 hwY1731TestIdSingleSynLossLocalRatio | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.8 | Unsigned32 | read-only | This object identifies the packet loss ratio that is collected on a local end. |
| I32 hwY1731TestIdSingleSynLossLossRemote | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.9 | Integer32 | read-only | This object identifies the packet loss statistics that are collected on a remote end. |
| U32 hwY1731TestIdSingleSynLossRemoteRatio | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.10 | Unsigned32 | read-only | This object identifies the packet loss ratio that is collected on a remote end. |
| DAT hwY1731TestIdSingleSynLossOnDemandStartTime | 1.3.6.1.4.1.2011.5.25.136.1.8.2.16.1.11 | DateAndTime | read-only | The date and time of the single-synthetic loss on-demand data. |
| U32 hwY1731AisMaxPktNum | 1.3.6.1.4.1.2011.5.25.136.1.8.3 | Unsigned32 | accessible-for-notify | The MAXIMUM of AIS packets transmitted in one second. |
| ENA hwY1731PMModeEnable | 1.3.6.1.4.1.2011.5.25.136.1.8.4 | EnabledStatus | read-write | This object indicates whether the y1731 summary statistic data is managed by Performace(PM) module, If it is enabled(1), the y1731 summary statistic data is managed, saved ane sent to NMS by Performace(PM) module. The default value is disabled(2). |
| hwY1731GlobalObject | 1.3.6.1.4.1.2011.5.25.136.1.8.5 | |||
| U32 hwY1731MaxTestId | 1.3.6.1.4.1.2011.5.25.136.1.8.5.1 | Unsigned32 | read-only | This object indicates the maximum value of TestId in current configuration. The value can be 0 or rangs from 1 to 4294967295. The value 0 is an invalid value. |
| U32 hwY1731LckMaxPktNum | 1.3.6.1.4.1.2011.5.25.136.1.8.5.2 | Unsigned32 | accessible-for-notify | The max LCK packets transmitted or received in 1 second. |
| U32 hwY1731LckCurrentPktNum | 1.3.6.1.4.1.2011.5.25.136.1.8.5.3 | Unsigned32 | accessible-for-notify | The current LCK packets transmitting or receiving. |
| U32 hwY1731LckUpperThreshold | 1.3.6.1.4.1.2011.5.25.136.1.8.5.4 | Unsigned32 | accessible-for-notify | The object is used to set the upper threshold value of LCK packets. The value range is from 1 to 100. The default means 80. |
| U32 hwY1731LckLowerThreshold | 1.3.6.1.4.1.2011.5.25.136.1.8.5.5 | Unsigned32 | accessible-for-notify | The object is used to set the lower threshold value of LCK packets. The value range is from 1 to 100. The default means 70. |
RFC description
Monitors Ethernet OAM, CFM, and Y.1731 performance testing including delay, loss, and alarm functions.
Start monitoring Huawei carrier Ethernet switch/router (802.1ag CFM Ethernet OAM) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.