HM2-PLATFORM-ROUTING-MIB

All MIBs › HM2-PLATFORM-ROUTING-MIB

Organization: Hirschmann Automation and Control GmbH

Last Updated: 2011-09-08

Category: Routing Protocols, Technology: Routing, Technology: Routing/L3, Vendor: Belden

Description: Hirschmann HiOS (HM2) platform routing MIB for static and dynamic routing protocol configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HM2-PLATFORM-ROUTING-MIB?

HM2-PLATFORM-ROUTING-MIB is a Hirschmann HiOS (Platform2/HM2) enterprise MIB for Layer 3 switching, covering static and dynamic routing protocol configuration on Hirschmann industrial switches. It exposes configuration objects that control the device's routing behavior, such as static route definitions and enablement/parameters of dynamic routing protocols. Its monitoring relevance is primarily software/configuration status for the Layer 3 forwarding plane: an operator would use it to confirm which routing protocols are enabled, verify static routes are correctly provisioned, and detect misconfiguration that could cause a loss of Layer 3 connectivity in an industrial network segment. It likely depends on standard IETF routing MIB concepts (such as those in IP-FORWARD-MIB or protocol-specific MIBs) for the underlying routing table semantics it configures. It is typically deployed on Hirschmann HiOS-based industrial Ethernet switches in factory automation, energy, or transportation networks requiring Layer 3 routing at the edge, where HM2-PLATFORM-ROUTING-MIB SNMP monitoring helps confirm routing configuration hasn't drifted from intent.

IPNetwork Monitor allows you to monitor SNMP objects defined in HM2-PLATFORM-ROUTING-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Hirschmann HiOS-based industrial Ethernet switches

Monitoring Examples

No object/table names were supplied for this module, so a concrete polling example cannot be grounded in real identifiers; in general terms, an operator would check static route configuration objects and dynamic routing protocol enablement/status objects to confirm routing is functioning as designed and to detect a missing or incorrect route causing a segment of an industrial network to lose connectivity.

What Can Be Monitored

static route configuration
dynamic routing protocol enablement
Layer 3 routing status

Imported Objects

From HM2-TC-MIB

HmEnabledStatus
hm2PlatformMibs	OBJECT-IDENTITY

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressIPv4
InetAddressType

From OSPF-MIB

RouterID
ospfAreaEntry	OBJECT-TYPE
ospfIfEntry
ospfIfMetricEntry
ospfNbrEntry
ospfVirtIfEntry

From Q-BRIDGE-MIB

VlanId

From RFC1213-MIB

PhysAddress

From RIPv2-MIB

rip2IfConfEntry

OBJECT-TYPE

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

From VRRP-MIB

vrrpOperVrId

OBJECT-TYPE

How to Use in IPNetwork Monitor

Example using hm2AgentDhcpClientMsgsReceived OID:

Select a Hirschmann HiOS Platform2 industrial switch (Layer 3 routing) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hm2AgentDhcpClientMsgsReceived into the Find box to locate it in the OID tree, then select it and click OK. The Number of DHCP Requests Received. Total number of DHCP requests received from all clients. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hm2PlatformRouting	1.3.6.1.4.1.248.12.2			The Hirschmann Platform2 MIB for Layer3 Switching. Copyright (C) 2011. All Rights Reserved.
hm2AgentSwitchArpGroup	1.3.6.1.4.1.248.12.2.1
I32 hm2AgentSwitchArpAgeoutTime	1.3.6.1.4.1.248.12.2.1.1	Integer32	read-write	HiOS: Configures the exact ARP entry age-out time in seconds. HiSecOS: Configures the average ARP entry age-out time in seconds, with each entry aging out after a random time between 0.5hm2AgentSwitchArpAgeoutTime and 1.5hm2AgentSwitchArpAgeoutTime.
I32 hm2AgentSwitchArpResponseTime	1.3.6.1.4.1.248.12.2.1.2	Integer32	read-write	Configures the ARP request response timeout in seconds. Allowable range: 1-10
I32 hm2AgentSwitchArpMaxRetries	1.3.6.1.4.1.248.12.2.1.3	Integer32	read-write	Configures the ARP count of maximum request for retries. Allowable range: 0-10
I32 hm2AgentSwitchArpCacheSize	1.3.6.1.4.1.248.12.2.1.4	Integer32	read-write	Configures the ARP maximum number of entries in the cache. Allowable range is platform specific.
HME hm2AgentSwitchArpDynamicRenew	1.3.6.1.4.1.248.12.2.1.5	HmEnabledStatus	read-write	This indicates the current setting of ARP dynamic renew mode.
G32 hm2AgentSwitchArpTotalEntryCountCurrent	1.3.6.1.4.1.248.12.2.1.6	Gauge32	read-only	Current number of entries in the ARP cache.
G32 hm2AgentSwitchArpTotalEntryCountPeak	1.3.6.1.4.1.248.12.2.1.7	Gauge32	read-only	Peak number of entries recorded in the ARP cache over time. This value is restarted whenever the ARP cache size is changed.
G32 hm2AgentSwitchArpStaticEntryCountCurrent	1.3.6.1.4.1.248.12.2.1.8	Gauge32	read-only	Current number of configured static ARP entries.
I32 hm2AgentSwitchArpStaticEntryCountMax	1.3.6.1.4.1.248.12.2.1.9	Integer32	read-only	Maximum number of configurable static ARP entries.
hm2AgentSwitchLocalProxyArpTable	1.3.6.1.4.1.248.12.2.1.11		not-accessible	This table contains the per-interface configuration parameters for local proxy ARP.
hm2AgentSwitchLocalProxyArpEntry	1.3.6.1.4.1.248.12.2.1.11.1		not-accessible	Represents a logical row in the hm2AgentSwitchLocalProxyArpTable.
HME hm2AgentSwitchLocalProxyArpMode	1.3.6.1.4.1.248.12.2.1.11.1.1	HmEnabledStatus	read-write	The local proxy ARP mode for the interface.
hm2AgentSwitchIntfArpTable	1.3.6.1.4.1.248.12.2.1.12		not-accessible	This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information.
hm2AgentSwitchIntfArpEntry	1.3.6.1.4.1.248.12.2.1.12.1		not-accessible	This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information.
IP hm2AgentSwitchIntfArpIpAddress	1.3.6.1.4.1.248.12.2.1.12.1.1	IpAddress	not-accessible	The Type of Address assigned to this interface.
NUM hm2AgentSwitchIntfArpIfIndex	1.3.6.1.4.1.248.12.2.1.12.1.2	InterfaceIndex	not-accessible	The Associated IfIndex which identified the ARP Entry. This value must be specified for static ARP entries on an unnumbered interface
TIK hm2AgentSwitchIntfArpAge	1.3.6.1.4.1.248.12.2.1.12.1.3	TimeTicks	read-only	This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.
PHY hm2AgentSwitchIntfArpMacAddress	1.3.6.1.4.1.248.12.2.1.12.1.4	PhysAddress	read-create	The hardware MAX Address that each interface maps to.
INT hm2AgentSwitchIntfArpType	1.3.6.1.4.1.248.12.2.1.12.1.5	INTEGER	read-only	The type of ARP entry.
ROW hm2AgentSwitchIntfArpStatus	1.3.6.1.4.1.248.12.2.1.12.1.6	RowStatus	read-create	The status of this ARP entry. Setting this object destroy will remove the entry.
HME hm2AgentSwitchArpSparseLearn	1.3.6.1.4.1.248.12.2.1.100	HmEnabledStatus	read-write	This indicates the current setting of ARP sparse learn mode.
INT hm2AgentSwitchArpCacheClear	1.3.6.1.4.1.248.12.2.1.101	INTEGER	read-write	Setting the object to 'flushARP' will flush the ARP cache. Setting the object to 'flushARPWithGateway' will also flush the ARP cache but includes the ARP entries that are used by gateways of routes. Reading the object always returns 'other'.
I32 hm2AgentSwitchProxyArpMaxResponseDelay	1.3.6.1.4.1.248.12.2.1.248	Integer32	read-write	Configures the maximum time in ms to wait before a proxy response is sent. Setting this to 0 determines a response to be sent immediately.
hm2AgentSwitchIpGroup	1.3.6.1.4.1.248.12.2.2
HME hm2AgentSwitchIpRoutingMode	1.3.6.1.4.1.248.12.2.2.1	HmEnabledStatus	read-write	Administratively enables/disables routing on the switch.
IP hm2AgentSwitchIpDefaultGateway	1.3.6.1.4.1.248.12.2.2.2	IpAddress	read-write	Specifies the default gateway manually configured.
hm2AgentSwitchIpInterfaceTable	1.3.6.1.4.1.248.12.2.2.3		not-accessible	IP interface table.
hm2AgentSwitchIpInterfaceEntry	1.3.6.1.4.1.248.12.2.2.3.1		not-accessible	IP interface entry.
NUM hm2AgentSwitchIpInterfaceIfIndex	1.3.6.1.4.1.248.12.2.2.3.1.1	InterfaceIndex	read-only	The IfIndex associated with this instance.
INT hm2AgentSwitchIPAddressConfigMethod	1.3.6.1.4.1.248.12.2.2.3.1.2	INTEGER	read-write	The source of the IP address. User can set the object to none(0) or dhcp(2). Option dhcp(2) enables DHCP client on the interface. Option none(0) disables DHCP client on the interface. Get on this object returns manual(1) only when the interface has a manually configured address.
IP hm2AgentSwitchIpInterfaceIpAddress	1.3.6.1.4.1.248.12.2.2.3.1.3	IpAddress	read-write	The IP address assigned to this interface. When setting this value, the value of hm2AgentSwitchIpInterfaceNetMask must be set at the same time.
IP hm2AgentSwitchIpInterfaceNetMask	1.3.6.1.4.1.248.12.2.2.3.1.4	IpAddress	read-write	The netmask assigned to this interface. When setting this value, the value of hm2AgentSwitchIpInterfaceIpAddress must be set at the same time.
HME hm2AgentSwitchIpInterfaceClearIp	1.3.6.1.4.1.248.12.2.2.3.1.5	HmEnabledStatus	read-write	When setting this object to 'enable(1)' the interfaces IP address and netmask will be set back to 0.0.0.0. Reading this object always returns 'disable(2).
HME hm2AgentSwitchIpInterfaceRoutingMode	1.3.6.1.4.1.248.12.2.2.3.1.6	HmEnabledStatus	read-write	Enables or disables routing for this interface.
HME hm2AgentSwitchIpInterfaceProxyARPMode	1.3.6.1.4.1.248.12.2.2.3.1.7	HmEnabledStatus	read-write	Enables or disables proxy ARP for this interface.
U32 hm2AgentSwitchIpInterfaceMtuValue	1.3.6.1.4.1.248.12.2.2.3.1.8	Unsigned32	read-write	Configures the MTU value for this interface. The applicable range is 68 to the , in bytes. Get of this object returns the effective MTU value on the interface. Set of this object with a value of 0 resets the MTU to the default IP MTU value on the interface. If a packet is received where the size exceeds the mtu value, an icmp destination unreachable message is sent back to the sender with the current mtu.
U32 hm2AgentSwitchIpInterfaceBandwidth	1.3.6.1.4.1.248.12.2.2.3.1.9	Unsigned32	read-write	Configures the bandwidth value for this interface. If the returned value is 0, bandwidth for this interface is not configured.
NUM hm2AgentSwitchIpInterfaceUnnumberedIfIndex	1.3.6.1.4.1.248.12.2.2.3.1.10	InterfaceIndexOrZero	read-only	If this object is non-zero, it indicates that the interface is unnumbered and specifies which interface the address is borrowed from.
HME hm2AgentSwitchIpInterfaceIcmpUnreachables	1.3.6.1.4.1.248.12.2.2.3.1.11	HmEnabledStatus	read-write	If this object is enabled, it indicates that ICMP unreachables can be sent on this interface.
HME hm2AgentSwitchIpInterfaceIcmpRedirects	1.3.6.1.4.1.248.12.2.2.3.1.12	HmEnabledStatus	read-write	If this object is enabled and hm2AgentSwitchIpIcmpRedirectsMode is also enabled, ICMP redirects can be sent on this interface.
INT hm2AgentSwitchDhcpOperation	1.3.6.1.4.1.248.12.2.2.3.1.13	INTEGER	read-write	Renew or release the IP address learned through DHCP. Get on this object always gives none. None means no operation is performed on DHCP.
INT hm2AgentSwitchIpInterfaceSuppressed	1.3.6.1.4.1.248.12.2.2.3.1.14	INTEGER	read-only	This mib variable contains the following values, which has the meaning as: 'unsuppressed' - The interface is not suppressed 'suppressed' - The interface is suppressed
U32 hm2AgentSwitchIpInterfaceNumberOfFlaps	1.3.6.1.4.1.248.12.2.2.3.1.15	Unsigned32	read-only	This mib variable displays the number of flaps occurred on the interface
U32 hm2AgentSwitchIpInterfaceCurrentPenalty	1.3.6.1.4.1.248.12.2.2.3.1.16	Unsigned32	read-only	This mib variable displays the current penalty of an interface
U32 hm2AgentSwitchIpInterfaceReUseTime	1.3.6.1.4.1.248.12.2.2.3.1.17	Unsigned32	read-only	This mib variable displays the number of seconds until the interface is allowed to come up
HME hm2AgentSwitchIpInterfaceNetdirectedBCMode	1.3.6.1.4.1.248.12.2.2.3.1.248	HmEnabledStatus	read-write	Enables or disables netdirected broadcasts for this interface.
hm2AgentSwitchIpRouterDiscoveryTable	1.3.6.1.4.1.248.12.2.2.4		not-accessible	There is no global administrative flag for router discovery. The global routing flag (hm2AgentSwitchIpRoutingMode) will be used for this purpose. If routing is disabled, router discovery is disabled as well.
hm2AgentSwitchIpRouterDiscoveryEntry	1.3.6.1.4.1.248.12.2.2.4.1		not-accessible	.
I32 hm2AgentSwitchIpRouterDiscoveryIfIndex	1.3.6.1.4.1.248.12.2.2.4.1.1	Integer32	read-only	Interface Number to configure Router Discovery on.
HME hm2AgentSwitchIpRouterDiscoveryAdvertiseMode	1.3.6.1.4.1.248.12.2.2.4.1.2	HmEnabledStatus	read-write	Enable or disable router discovery on the interface.
I32 hm2AgentSwitchIpRouterDiscoveryMaxAdvertisementInterval	1.3.6.1.4.1.248.12.2.2.4.1.3	Integer32	read-write	Maximum time allowed between sending router advertisements from the interface.
I32 hm2AgentSwitchIpRouterDiscoveryMinAdvertisementInterval	1.3.6.1.4.1.248.12.2.2.4.1.4	Integer32	read-write	Minimum time allowed between sending router advertisements from the interface. This value must be less than or equal to hm2AgentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
I32 hm2AgentSwitchIpRouterDiscoveryAdvertisementLifetime	1.3.6.1.4.1.248.12.2.2.4.1.5	Integer32	read-write	Value of lifetime field of router advertsisement sent from the interface. This value must be greater than or equal to hm2AgentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
I32 hm2AgentSwitchIpRouterDiscoveryPreferenceLevel	1.3.6.1.4.1.248.12.2.2.4.1.6	Integer32	read-write	Preferability of the address as a default router address, related to other addresses on the same subnet. This is defined as the larger the number, the higher the preference.
IP hm2AgentSwitchIpRouterDiscoveryAdvertisementAddress	1.3.6.1.4.1.248.12.2.2.4.1.7	IpAddress	read-write	Address used when sending router advertisements from the interface.
hm2AgentSwitchIpVlanTable	1.3.6.1.4.1.248.12.2.2.5		not-accessible	A static VLAN for which routing can be enabled/disabled.
hm2AgentSwitchIpVlanEntry	1.3.6.1.4.1.248.12.2.2.5.1		not-accessible	A static VLAN for which routing can be enabled/disabled.
VLA hm2AgentSwitchIpVlanId	1.3.6.1.4.1.248.12.2.2.5.1.1	VlanId	read-only	The VLAN's ID.
NUM hm2AgentSwitchIpVlanIfIndex	1.3.6.1.4.1.248.12.2.2.5.1.2	InterfaceIndex	read-write	The IfIndex associated with this VLAN.
ROW hm2AgentSwitchIpVlanRoutingStatus	1.3.6.1.4.1.248.12.2.2.5.1.3	RowStatus	read-create	Status of Routing mode per VLAN. active(1) - VLAN is enabled for routing createAndGo(4) - Adds VLAN entry for routing createAndWait(5) - Adds VLAN entry for routing destroy(6) - Removes VLAN from routing
hm2AgentSwitchSecondaryAddressTable	1.3.6.1.4.1.248.12.2.2.6		not-accessible	Contains a list of secondary IP addresses associated with an interface.
hm2AgentSwitchSecondaryAddressEntry	1.3.6.1.4.1.248.12.2.2.6.1		not-accessible	A secondary IP address for a given interface. This IP address must not conflict with the IP address configured in the hm2AgentSwitchIpInterfaceTable.
IP hm2AgentSwitchSecondaryIpAddress	1.3.6.1.4.1.248.12.2.2.6.1.1	IpAddress	not-accessible	The secondary IP address assigned to this interface.
IP hm2AgentSwitchSecondaryNetMask	1.3.6.1.4.1.248.12.2.2.6.1.2	IpAddress	read-create	The secondary netmask assigned to this interface. This value must be set during creation and can not be changed.
ROW hm2AgentSwitchSecondaryStatus	1.3.6.1.4.1.248.12.2.2.6.1.3	RowStatus	read-create	Creates a new entry in the secondary address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The hm2AgentSwitchSecondaryNetMask object must be set during creation. destroy(6) - Removes the associated address from the interface.
hm2AgentSwitchIpIcmpControlGroup	1.3.6.1.4.1.248.12.2.2.8
HME hm2AgentSwitchIpIcmpEchoReplyMode	1.3.6.1.4.1.248.12.2.2.8.1	HmEnabledStatus	read-write	Sets the administrative Echo Reply Mode.
HME hm2AgentSwitchIpIcmpRedirectsMode	1.3.6.1.4.1.248.12.2.2.8.2	HmEnabledStatus	read-write	Sets the administrative Mode for sending Redirects.
I32 hm2AgentSwitchIpIcmpRateLimitInterval	1.3.6.1.4.1.248.12.2.2.8.3	Integer32	read-write	HiOS: Specifies the time interval between tokens being placed in the bucket for ICMP Ratelimit. HiSecOS: Specifies the average minimum time between subsequent ICMP packets for each destination, using a token bucket algorithm. In times without ICMP packets, the tokens accumulate to allow for bursts of up to hm2AgentSwitchIpIcmpRateLimitBurstSize packets.
I32 hm2AgentSwitchIpIcmpRateLimitBurstSize	1.3.6.1.4.1.248.12.2.2.8.4	Integer32	read-write	HiOS: Specifies the number of tokens to be placed after timeout. HiSecOS: The size of the token bucket, fixed at 6 tokens.
hm2AgentSwitchIntfIpHelperAddressTable	1.3.6.1.4.1.248.12.2.2.10		not-accessible	Contains a list of IP helper addresses associated with an interface.
hm2AgentSwitchIntfIpHelperAddressEntry	1.3.6.1.4.1.248.12.2.2.10.1		not-accessible	An IP helper address for a given interface.
U32 hm2AgentSwitchIntfIpHelperUdpPort	1.3.6.1.4.1.248.12.2.2.10.1.1	Unsigned32	not-accessible	UDP port number. Received packets with this destination UDP port number are forwarded to the helper address in this entry. A relay entry with port 0 allows dhcp, time, winnameserver, tacacs, dns, tftp, netbios-ns and netbios-dgm relay.
IP hm2AgentSwitchIntfIpHelperIpAddress	1.3.6.1.4.1.248.12.2.2.10.1.2	IpAddress	not-accessible	An IP helper address for packets received on this interface. An address of 0.0.0.0 identifies the entry as a discard entry. Packets that match a discard entry are dropped.
U32 hm2AgentSwitchIntfIpHelperHitCount	1.3.6.1.4.1.248.12.2.2.10.1.4	Unsigned32	read-only	The number of times a packet has been forwarded or discarded according to this entry.
ROW hm2AgentSwitchIntfIpHelperStatus	1.3.6.1.4.1.248.12.2.2.10.1.5	RowStatus	read-create	Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.
INT hm2AgentSwitchClearIpDefaultGateway	1.3.6.1.4.1.248.12.2.2.11	INTEGER	read-write	Resets the Global Default Gateway address.
IPt hm2AgentSwitchIpFirstActiveAddressType	1.3.6.1.4.1.248.12.2.2.248	InetAddressType	read-only	The type of hm2AgentSwitchIpFirstActiveAddress.
IP hm2AgentSwitchIpFirstActiveAddress	1.3.6.1.4.1.248.12.2.2.249	InetAddress	read-only	The lowest ip address of any active routing interface.
I32 hm2AgentSwitchIpStaticDefaultPref	1.3.6.1.4.1.248.12.2.2.250	Integer32	read-write	The default preference for static routes.
hm2AgentRouterRipConfigGroup	1.3.6.1.4.1.248.12.2.3
HME hm2AgentRouterRipAdminState	1.3.6.1.4.1.248.12.2.3.1	HmEnabledStatus	read-write	Sets the administrative mode of RIP in the router.
INT hm2AgentRouterRipSplitHorizonMode	1.3.6.1.4.1.248.12.2.3.2	INTEGER	read-write	Sets the RIP split horizon operating mode in the router. A value of none(1) means split horizon processing is disabled. When set to simple(2), the simple split horizon technique is used. When set to poisonReverse(3), the split horizon with poison reverse technique is used. The default split horizon mode is simple(2).
HME hm2AgentRouterRipAutoSummaryMode	1.3.6.1.4.1.248.12.2.3.3	HmEnabledStatus	read-write	Sets the RIP auto summarization mode in the router. A value of enable(1) means that routes advertized by this RIP router are combined, or summarized, whenever possible into aggregates. When set to disable(2), routes are not aggregated in RIP updates generated by this router. The default auto summary mode is enable(1).
HME hm2AgentRouterRipHostRoutesAcceptMode	1.3.6.1.4.1.248.12.2.3.4	HmEnabledStatus	read-write	Sets the RIP host route acceptance mode in the router. A value of enable(1) means that host routes advertized to this RIP router will be accepted (learned) into its routing table. When set to disable(2), host routes advertized in RIP updates from neighboring routers are ignored. The default host routes accept mode is enable(1).
I32 hm2AgentRouterRipDefaultMetric	1.3.6.1.4.1.248.12.2.3.5	Integer32	read-write	Default metric of redistributed routes, when RIP redistributes from other protocols. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..15).
T/F hm2AgentRouterRipDefaultMetricConfigured	1.3.6.1.4.1.248.12.2.3.6	TruthValue	read-write	Flag to determine whether RIP default-metric is configured or not. Set to 'false' to unconfigure the default route metric. Set to 'true' is not allowed.
T/F hm2AgentRouterRipDefaultInfoOriginate	1.3.6.1.4.1.248.12.2.3.7	TruthValue	read-write	Flag to determine, whether RIP can advertise a default-route learned from another protocol.
hm2AgentRipRouteRedistTable	1.3.6.1.4.1.248.12.2.3.8		not-accessible	This table contains the MIB objects required to configure route-redistribution for RIP. Here, RIP is the Destination protocol and the source protocols can be any of : BGP, OSPF, Static, Connected.
hm2AgentRipRouteRedistEntry	1.3.6.1.4.1.248.12.2.3.8.1		not-accessible	The entries of the table.
INT hm2AgentRipRouteRedistSource	1.3.6.1.4.1.248.12.2.3.8.1.1	INTEGER	read-only	Source route, from which RIP can redistribute routes. This object also acts as the identifier for the RIP redistribution Table entry.
HME hm2AgentRipRouteRedistMode	1.3.6.1.4.1.248.12.2.3.8.1.2	HmEnabledStatus	read-write	User enabels/disables route-redistribution for a particular source protocol.
I32 hm2AgentRipRouteRedistMetric	1.3.6.1.4.1.248.12.2.3.8.1.3	Integer32	read-write	Metric used for redistributing a particular source protocol route into RIP. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..15).
T/F hm2AgentRipRouteRedistMetricConfigured	1.3.6.1.4.1.248.12.2.3.8.1.4	TruthValue	read-write	Flag to determine whether RIP redistribute-metric is configured or not. Set to 'false' to unconfigure redistribute metric. Set to 'true' is not allowed.
INT hm2AgentRipRouteRedistMatchInternal	1.3.6.1.4.1.248.12.2.3.8.1.5	INTEGER	read-write	If this flag is true, RIP redistributes OSPF internal routes. It will be non-applicable, when source protocol is other than ospf.
INT hm2AgentRipRouteRedistMatchExternal1	1.3.6.1.4.1.248.12.2.3.8.1.6	INTEGER	read-write	If this flag is true, RIP redistributes OSPF External1 routes. It will be non-applicable, when source protocol is other than ospf.
INT hm2AgentRipRouteRedistMatchExternal2	1.3.6.1.4.1.248.12.2.3.8.1.7	INTEGER	read-write	If this flag is true, RIP redistributes OSPF External2 routes. It will be non-applicable, when source protocol is other than ospf.
INT hm2AgentRipRouteRedistMatchNSSAExternal1	1.3.6.1.4.1.248.12.2.3.8.1.8	INTEGER	read-write	If this flag is true, RIP redistributes OSPF NSSA-External1 routes. It will be non-applicable, when source protocol is other than ospf.
INT hm2AgentRipRouteRedistMatchNSSAExternal2	1.3.6.1.4.1.248.12.2.3.8.1.9	INTEGER	read-write	If this flag is true, RIP redistributes OSPF NSSA-External2 routes. It will be non-applicable, when source protocol is other than ospf.
U32 hm2AgentRipRouteRedistDistList	1.3.6.1.4.1.248.12.2.3.8.1.10	Unsigned32	read-write	Access-list number of the access-list, which filters routes received from a source-protocol.
T/F hm2AgentRipRouteRedistDistListConfigured	1.3.6.1.4.1.248.12.2.3.8.1.11	TruthValue	read-write	Flag to determine whether Access-list is configured or not.
hm2AgentRip2IfConfTable	1.3.6.1.4.1.248.12.2.3.9		not-accessible	A list of subnets which require separate configuration in RIP. Augments rip2IfConfTable in the RIPv2-MIB.
hm2AgentRip2IfConfEntry	1.3.6.1.4.1.248.12.2.3.9.1		not-accessible	A Single Routing Domain in a single Subnet. Augments rip2IfConfEntry in RIPv2-MIB.
I32 hm2AgentRip2IfConfAuthKeyId	1.3.6.1.4.1.248.12.2.3.9.1.1	Integer32	read-create	The identifier for the authentication key used on this interface. This field is only meaningful when the RIPv2-MIB rip2IfConfAuthType is md5(3); otherwise, the value is not used.
I32 hm2AgentRouterRipRoutePref	1.3.6.1.4.1.248.12.2.3.10	Integer32	read-write	The route preference, sometimes called administrative distance, for RIP routes. A route with a preference of 255 is considered unreachable.
I32 hm2AgentRouterRipUpdateTimerInterval	1.3.6.1.4.1.248.12.2.3.248	Integer32	read-write	Sets the RIP update timer interval in the router. This is the time in seconds between two full routing table update packets.
hm2AgentRouterOspfConfigGroup	1.3.6.1.4.1.248.12.2.4
I32 hm2AgentOspfDefaultMetric	1.3.6.1.4.1.248.12.2.4.1	Integer32	read-write	Default metric of redistributed routes, when OSPF redistributes from other protocols. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..16777214).
T/F hm2AgentOspfDefaultMetricConfigured	1.3.6.1.4.1.248.12.2.4.2	TruthValue	read-write	Flag to determine whether OSPF default-metric is configured or not. Set to 'false' to unconfigure the OSPF default-metric. Set to 'true' is not allowed.
T/F hm2AgentOspfDefaultInfoOriginate	1.3.6.1.4.1.248.12.2.4.3	TruthValue	read-write	Flag to determine, whether OSPF can advertise a default-route learned from another protocol.
T/F hm2AgentOspfDefaultInfoOriginateAlways	1.3.6.1.4.1.248.12.2.4.4	TruthValue	read-write	When this flag is true, the router advertises 0.0.0.0/0.0.0.0 always. Without this option, OSPF will only advertise 0.0.0.0/0.0.0.0 if the router's forwarding table contains a default route.
I32 hm2AgentOspfDefaultInfoOriginateMetric	1.3.6.1.4.1.248.12.2.4.5	Integer32	read-write	Metric of the default route, which OSPF advertises when learned from other protocol. (0) indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..16777214).
T/F hm2AgentOspfDefaultInfoOriginateMetricConfigured	1.3.6.1.4.1.248.12.2.4.6	TruthValue	read-write	Flag to determine whether OSPF default-info originate metric is configured or not. Setting to false unconfigures the default route metric. Setting to true is not allowed.
INT hm2AgentOspfDefaultInfoOriginateMetricType	1.3.6.1.4.1.248.12.2.4.7	INTEGER	read-write	Metric Type of the default route,which OSPF advertises when learned from other protocol. It can be 1(external type 1) or 2(external type 2).
hm2AgentOspfRouteRedistTable	1.3.6.1.4.1.248.12.2.4.8		not-accessible	This table contains the MIB objects required to configure route-redistribution for OSPF. Here, OSPF is the Destination protocol and the source protocols can be any of : BGP, RIP, Static, Connected.
hm2AgentOspfRouteRedistEntry	1.3.6.1.4.1.248.12.2.4.8.1		not-accessible	The entries of the table.
INT hm2AgentOspfRouteRedistSource	1.3.6.1.4.1.248.12.2.4.8.1.1	INTEGER	read-only	Source protocol, from which OSPF can redistribute routes. This object also acts as the identifier for the OSPF redistribution Table entry.
HME hm2AgentOspfRouteRedistMode	1.3.6.1.4.1.248.12.2.4.8.1.2	HmEnabledStatus	read-write	User enables/disables route-redistribution for a particular source protocol.
I32 hm2AgentOspfRouteRedistMetric	1.3.6.1.4.1.248.12.2.4.8.1.3	Integer32	read-write	Metric used for redistributing a particular source protocol route into OSPF.
T/F hm2AgentOspfRouteRedistMetricConfigured	1.3.6.1.4.1.248.12.2.4.8.1.4	TruthValue	read-write	Flag to determine whether OSPF redistribute-metric is configured or not.
INT hm2AgentOspfRouteRedistMetricType	1.3.6.1.4.1.248.12.2.4.8.1.5	INTEGER	read-write	Metric Type of routes,which OSPF redistributes from other source protocols. It can be 1(external type 1) or 2(external type 2).
U32 hm2AgentOspfRouteRedistTag	1.3.6.1.4.1.248.12.2.4.8.1.6	Unsigned32	read-write	It specifies the tag field in routes redistributed by OSPF.
T/F hm2AgentOspfRouteRedistSubnets	1.3.6.1.4.1.248.12.2.4.8.1.7	TruthValue	read-write	If this value is false, then OSPF will not redistribute subnetted routes.
U32 hm2AgentOspfRouteRedistDistList	1.3.6.1.4.1.248.12.2.4.8.1.8	Unsigned32	read-write	Access-list number of the access-list, which filters routes received from a source-protocol. HiOS: Valid access list numbers are between 1000 and 1099. HiSecOS: Valid access list numbers are between 1 and 10000.
T/F hm2AgentOspfRouteRedistDistListConfigured	1.3.6.1.4.1.248.12.2.4.8.1.9	TruthValue	read-write	Flag to determine whether Access-list is configured or not.
hm2AgentOspfIfTable	1.3.6.1.4.1.248.12.2.4.9		not-accessible	The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF. Augments ospfIfTable from the OSPF-MIB.
hm2AgentOspfIfEntry	1.3.6.1.4.1.248.12.2.4.9.1		not-accessible	The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF. Augments ospfIfEntry in OSPF-MIB.
I32 hm2AgentOspfIfAuthKeyId	1.3.6.1.4.1.248.12.2.4.9.1.1	Integer32	read-create	The identifier for the authentication key used on this interface. This field is only meaningful when the OSPF-MIB ospfIfAuthType is md5(2); otherwise, the value is not used.
HME hm2AgentOspfIfIpMtuIgnoreFlag	1.3.6.1.4.1.248.12.2.4.9.1.2	HmEnabledStatus	read-write	Configures the IP MTU Ignore Flag value for this OSPF interface.
T/F hm2AgentOspfIfPassiveMode	1.3.6.1.4.1.248.12.2.4.9.1.3	TruthValue	read-write	Flag to determine whether the interface is passive. A passive interface will not participate in the OSPF adjacency formation.
HME hm2AgentOspfIfAdvertiseSecondaries	1.3.6.1.4.1.248.12.2.4.9.1.4	HmEnabledStatus	read-write	Configures the advertisability of the secondary addresses configured on this interface.
HME hm2AgentOspfIfFastHelloMode	1.3.6.1.4.1.248.12.2.4.9.1.248	HmEnabledStatus	read-write	Configures the fast hello mode on this interface. If enabled, hello packets are sent every 250ms, ospfIfHelloInterval is ignored. The dead interval and spf delay need to be re-configured accordingly for faster convergence.
hm2AgentOspfVirtIfTable	1.3.6.1.4.1.248.12.2.4.10		not-accessible	Information about this router's virtual inter- faces. Augments ospfVirtIfTable from the OSPF-MIB.
hm2AgentOspfVirtIfEntry	1.3.6.1.4.1.248.12.2.4.10.1		not-accessible	Information about a single Virtual Interface. Augments ospfVirtIfEntry in OSPF-MIB.
I32 hm2AgentOspfVirtIfAuthKeyId	1.3.6.1.4.1.248.12.2.4.10.1.1	Integer32	read-create	The identifier for the authentication key used on this virtual interface. This field is only meaningful when the OSPF-MIB ospfVirtIfAuthType is md5(2); otherwise, the value is not used.
HME hm2AgentRouterOspfRFC1583CompatibilityMode	1.3.6.1.4.1.248.12.2.4.11	HmEnabledStatus	read-write	From RFC2328: Controls the preference rules used in Section 16.4 when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583 ([Ref9]). When set to 'disabled', the preference rules are those stated in Section 16.4.1, which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas. Set to 'enabled' by default. In order to minimize the chance of routing loops, all OSPF routers in an OSPF routing domain should have RFC1583Compatibility set identically. When there are routers present that have not been updated with the functionality specified in Section 16.4.1 of this memo, all routers should have RFC1583Compatibility set to 'enabled'. Otherwise, all routers should have RFC1583Compatibility set to 'disabled', preventing all routing loops.
I32 hm2AgentOspfSpfDelayTime	1.3.6.1.4.1.248.12.2.4.12	Integer32	read-write	Delay time (in seconds) between when OSPF receives a topology change and when it starts an SPF calculation. It can be an integer from 0 to 65535. The default time is 5 seconds. A value of 0 means that there is no delay; that is, the SPF calculation is started immediately.
I32 hm2AgentOspfSpfHoldTime	1.3.6.1.4.1.248.12.2.4.13	Integer32	read-write	Minimum time (in seconds) between two consecutive SPF calculations. It can be an integer from 0 to 65535. The default time is 10 seconds. A value of 0 means that there is no delay; that is, two SPF calculations can be done, one immediately after the other.
U32 hm2AgentOspfAutoCostRefBw	1.3.6.1.4.1.248.12.2.4.14	Unsigned32	read-write	Auto cost reference bandwidth of the router interfaces for ospf metric calculations. It can be an integer from 1 to 4294967. The default reference bandwidth is 100 Mbps.
T/F hm2AgentOspfOpaqueLsaSupport	1.3.6.1.4.1.248.12.2.4.15	TruthValue	read-write	The router's support for Opaque LSA types. This object is persistent and when written the entity SHOULD save the change to non-volatile storage.
hm2AgentOspfAreaOpaqueLsdbTable	1.3.6.1.4.1.248.12.2.4.16		not-accessible	The OSPF Process's Area Link State Database (LSDB). The LSDB contains type-10 Link State Advertisements from throughout the areas that the device is attached to.
hm2AgentOspfAreaOpaqueLsdbEntry	1.3.6.1.4.1.248.12.2.4.16.1		not-accessible	A single AreaOpaque Link State Advertisement.
IP hm2AgentOspfAreaOpaqueLsdbAreaId	1.3.6.1.4.1.248.12.2.4.16.1.1	IpAddress	read-only	The 32 bit identifier of the Area from which the LSA was received.
INT hm2AgentOspfAreaOpaqueLsdbType	1.3.6.1.4.1.248.12.2.4.16.1.2	INTEGER	read-only	The type of the link state advertisement. Each link state type has a separate advertisement format.
IP hm2AgentOspfAreaOpaqueLsdbLsid	1.3.6.1.4.1.248.12.2.4.16.1.3	IpAddress	read-only	The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
ROU hm2AgentOspfAreaOpaqueLsdbRouterId	1.3.6.1.4.1.248.12.2.4.16.1.4	RouterID	read-only	The 32 bit number that uniquely identifies the originating router in the Autonomous System.
I32 hm2AgentOspfAreaOpaqueLsdbSequence	1.3.6.1.4.1.248.12.2.4.16.1.5	Integer32	read-only	The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
I32 hm2AgentOspfAreaOpaqueLsdbAge	1.3.6.1.4.1.248.12.2.4.16.1.6	Integer32	read-only	This field is the age of the link state advertisement in seconds.
I32 hm2AgentOspfAreaOpaqueLsdbChecksum	1.3.6.1.4.1.248.12.2.4.16.1.7	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT hm2AgentOspfAreaOpaqueLsdbAdvertisement	1.3.6.1.4.1.248.12.2.4.16.1.8	OCTET STRING	read-only	The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size
hm2AgentOspfLocalLsdbTable	1.3.6.1.4.1.248.12.2.4.17		not-accessible	The OSPF Process's Link-Local Link State Database for non-virtual links. This table is identical to the OSPF LSDB Table in format, but contains only Link-Local Link State Advertisements for non-virtual links. The purpose is to allow Link-Local LSAs to be displayed for each non-virtual interface. This table is implemented to support type-9 LSAs which are defined in 'The OSPF Opaque LSA Option'.
hm2AgentOspfLocalLsdbEntry	1.3.6.1.4.1.248.12.2.4.17.1		not-accessible	A single Link State Advertisement.
IP hm2AgentOspfLocalLsdbIpAddress	1.3.6.1.4.1.248.12.2.4.17.1.1	IpAddress	read-only	The IP Address of the interface from which the LSA was received if the interface is numbered.
NUM hm2AgentOspfLocalLsdbAddressLessIf	1.3.6.1.4.1.248.12.2.4.17.1.2	InterfaceIndexOrZero	read-only	The Interface Index of the interface from which the LSA was received if the interface is unnumbered.
INT hm2AgentOspfLocalLsdbType	1.3.6.1.4.1.248.12.2.4.17.1.3	INTEGER	read-only	The type of the link state advertisement. Each link state type has a separate advertise- ment format.
IP hm2AgentOspfLocalLsdbLsid	1.3.6.1.4.1.248.12.2.4.17.1.4	IpAddress	read-only	The Link State ID is an LS Type Specific field containing a 32 bit identifier in IP address format; it identifies the piece of the routing domain that is being described by the advertisement.
ROU hm2AgentOspfLocalLsdbRouterId	1.3.6.1.4.1.248.12.2.4.17.1.5	RouterID	read-only	The 32 bit number that uniquely identifies the originating router in the Autonomous System.
I32 hm2AgentOspfLocalLsdbSequence	1.3.6.1.4.1.248.12.2.4.17.1.6	Integer32	read-only	The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
I32 hm2AgentOspfLocalLsdbAge	1.3.6.1.4.1.248.12.2.4.17.1.7	Integer32	read-only	This field is the age of the link state adver- tisement in seconds.
I32 hm2AgentOspfLocalLsdbChecksum	1.3.6.1.4.1.248.12.2.4.17.1.8	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT hm2AgentOspfLocalLsdbAdvertisement	1.3.6.1.4.1.248.12.2.4.17.1.9	OCTET STRING	read-only	The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size.
hm2AgentOspfAsLsdbTable	1.3.6.1.4.1.248.12.2.4.18		not-accessible	The OSPF Process's AS-scope LSA Link State Database. The Database contains the AS-scope Link State Advertisements from throughout the areas that the device is attached to. This table is identical to the OSPF LSDB Table in format, but contains only AS-scope Link State Advertisements. The purpose is to allow AS-scope LSAs to be displayed once for the router rather than once in each non-stub area.
hm2AgentOspfAsLsdbEntry	1.3.6.1.4.1.248.12.2.4.18.1		not-accessible	A single Link State Advertisement.
INT hm2AgentOspfAsLsdbType	1.3.6.1.4.1.248.12.2.4.18.1.1	INTEGER	read-only	The type of the link state advertisement. Each link state type has a separate advertise- ment format.
IP hm2AgentOspfAsLsdbLsid	1.3.6.1.4.1.248.12.2.4.18.1.2	IpAddress	read-only	The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
ROU hm2AgentOspfAsLsdbRouterId	1.3.6.1.4.1.248.12.2.4.18.1.3	RouterID	read-only	The 32 bit number that uniquely identifies the originating router in the Autonomous System.
I32 hm2AgentOspfAsLsdbSequence	1.3.6.1.4.1.248.12.2.4.18.1.4	Integer32	read-only	The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
I32 hm2AgentOspfAsLsdbAge	1.3.6.1.4.1.248.12.2.4.18.1.5	Integer32	read-only	This field is the age of the link state adver- tisement in seconds.
I32 hm2AgentOspfAsLsdbChecksum	1.3.6.1.4.1.248.12.2.4.18.1.6	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT hm2AgentOspfAsLsdbAdvertisement	1.3.6.1.4.1.248.12.2.4.18.1.7	OCTET STRING	read-only	The entire Link State Advertisement, including its header.
T/F hm2AgentOspfDefaultPassiveMode	1.3.6.1.4.1.248.12.2.4.19	TruthValue	read-write	Flag to determine, whether all the interfaces are passive interfaces by default. A passive interface will not participate in the OSPF adjacency formation.
I32 hm2AgentOspfRoutePrefIntraArea	1.3.6.1.4.1.248.12.2.4.20	Integer32	read-write	The route preference, sometimes called administrative distance, for intra-area OSPFv2 routes. A route with a preference of 255 is considered unreachable.
I32 hm2AgentOspfRoutePrefInterArea	1.3.6.1.4.1.248.12.2.4.21	Integer32	read-write	The route preference, sometimes called administrative distance, for inter-area OSPFv2 routes. A route with a preference of 255 is considered unreachable.
I32 hm2AgentOspfRoutePrefExternal	1.3.6.1.4.1.248.12.2.4.22	Integer32	read-write	The route preference, sometimes called administrative distance, for external OSPFv2 routes. A route with a preference of 255 is considered unreachable.
hm2AgentOspfAreaNSSATable	1.3.6.1.4.1.248.12.2.4.248		not-accessible	Information about all the configured Not-So-Stubby-Area(NSSAs) in OSPF. Augments ospfAreaTable from the OSPF-MIB.
hm2AgentOspfAreaNSSAEntry	1.3.6.1.4.1.248.12.2.4.248.1		not-accessible	Information about a single Not-So-Stubby-Area(NSSA). Augments ospfAreaEntry in OSPF-MIB.
HME hm2AgentOspfAreaNSSAImportSummaries	1.3.6.1.4.1.248.12.2.4.248.1.1	HmEnabledStatus	read-write	When set to enabled, OSPF's summary routes are imported into the NSSA as Type-3 summary-LSAs. When set to disabled, summary routes are not imported into the NSSA. The default setting is enabled.
HME hm2AgentOspfAreaNSSARedistribute	1.3.6.1.4.1.248.12.2.4.248.1.2	HmEnabledStatus	read-write	When set to enabled NSSA ASBRs will not redistribute external routes into the NSSA and they will cease to originate Type-7 external LSAs for external routes.
T/F hm2AgentOspfAreaNSSADefaultInfoOriginate	1.3.6.1.4.1.248.12.2.4.248.1.3	TruthValue	read-write	Determines if the router will originate a Type-7 default LSA into the NSSA. This command will cause a default LSA to be originated only if the router is an NSSA ABR or ASBR.
I32 hm2AgentOspfAreaNSSADefaultMetric	1.3.6.1.4.1.248.12.2.4.248.1.4	Integer32	read-write	Defines the metric value advertised in the Type-7 default LSA originated by this router
INT hm2AgentOspfAreaNSSADefaultMetricType	1.3.6.1.4.1.248.12.2.4.248.1.5	INTEGER	read-write	Defines the metric type advertised in the Type-7 default LSA originated by this router
hm2AgentOspfIfMetricTable	1.3.6.1.4.1.248.12.2.4.249		not-accessible	Information about interface metrics.
hm2AgentOspfIfMetricEntry	1.3.6.1.4.1.248.12.2.4.249.1		not-accessible	Information about interface metrics.
I32 hm2AgentOspfIfMetricCalculatedCost	1.3.6.1.4.1.248.12.2.4.249.1.1	Integer32	read-only	Returns the actual cost value used by OSPF for this interface.
hm2AgentSnmpTrapFlagsConfigGroupLayer3	1.3.6.1.4.1.248.12.2.5
HME hm2AgentSnmpVRRPNewMasterTrapFlag	1.3.6.1.4.1.248.12.2.5.1	HmEnabledStatus	read-write	This flag enables the sending of VRRP new master notification traps.
HME hm2AgentSnmpVRRPAuthFailureTrapFlag	1.3.6.1.4.1.248.12.2.5.2	HmEnabledStatus	read-write	This flag enables the sending of VRRP authentication failure notification traps.
hm2AgentBootpDhcpRelayGroup	1.3.6.1.4.1.248.12.2.6
I32 hm2AgentBootpDhcpRelayMaxHopCount	1.3.6.1.4.1.248.12.2.6.1	Integer32	read-write	The BOOTP/DHCP Max Hop Count. The relay agent silently discards BOOTREQUEST messages whose hops field exceeds the value 16 assuming that the request is looped through the intermediate agents. The default value is 4.
I32 hm2AgentBootpDhcpRelayMinWaitTime	1.3.6.1.4.1.248.12.2.6.4	Integer32	read-write	The BOOTP/DHCP Minimum Wait Time. When the BOOTP relay agent receives a BOOTREQUEST message, it MAY use the value of the 'secs' (seconds since client began booting) field of the request as a factor in deciding whether to relay the request or not.
HME hm2AgentBootpDhcpRelayCircuitIdOptionMode	1.3.6.1.4.1.248.12.2.6.5	HmEnabledStatus	read-write	The BOOTP/DHCP Circuit ID Option Mode. This flag is set to enable/disable the network element to add/remove the DHCP Relay agent Circuit ID sub-options.
hm2AgentECMPGroup	1.3.6.1.4.1.248.12.2.7
I32 hm2AgentECMPOspfMaxPaths	1.3.6.1.4.1.248.12.2.7.1	Integer32	read-write	It sets the number of paths that OSPF can report for a given destination where maxpaths is platform-dependent.
hm2AgentRouterVrrpConfigGroup	1.3.6.1.4.1.248.12.2.8
HME hm2AgentRouterVrrpAdminState	1.3.6.1.4.1.248.12.2.8.1	HmEnabledStatus	read-write	Sets the administrative mode of VRRP in the router.
hm2AgentVrrpOperations	1.3.6.1.4.1.248.12.2.9
hm2AgentRouterVrrpOperTable	1.3.6.1.4.1.248.12.2.9.1		not-accessible	Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of `hm2AgentRouterVrrpOperEntry' items.
hm2AgentRouterVrrpOperEntry	1.3.6.1.4.1.248.12.2.9.1.1		not-accessible	An entry in the table contains operational priority that is associated with a virtual router.
I32 hm2AgentRouterVrrpOperPriority	1.3.6.1.4.1.248.12.2.9.1.1.1	Integer32	read-only	This object specifies the operational priority of the VRRP router. This value will be afftected by both the tracking process and the configured priority set by the vrrpOperPriority object.
I32 hm2AgentRouterVrrpNumberOfFastInst	1.3.6.1.4.1.248.12.2.9.248	Integer32	read-only	Number of VRRP instances with advertisement interval less than one second.
hm2AgentIpHelperGroup	1.3.6.1.4.1.248.12.2.11
HME hm2AgentIpHelperAdminMode	1.3.6.1.4.1.248.12.2.11.1	HmEnabledStatus	read-write	Administratively enable or disable IP helper.
C32 hm2AgentDhcpClientMsgsReceivedEx	1.3.6.1.4.1.248.12.2.11.2	Counter32	read-only	The Number of DHCP Requests Received. Total number of DHCP requests received from all clients.
C32 hm2AgentDhcpClientMsgsRelayed	1.3.6.1.4.1.248.12.2.11.3	Counter32	read-only	The Number of DHCP Requests Forwarded. Total number of DHCP requests relayed to a server.
C32 hm2AgentDhcpServerMsgsReceived	1.3.6.1.4.1.248.12.2.11.4	Counter32	read-only	The number of DHCP messages received from a server.
C32 hm2AgentDhcpServerMsgsRelayed	1.3.6.1.4.1.248.12.2.11.5	Counter32	read-only	The number of DHCP messages relayed to a server.
C32 hm2AgentUdpClientMsgsReceived	1.3.6.1.4.1.248.12.2.11.6	Counter32	read-only	The number of UDP messages received from all clients.
C32 hm2AgentUdpClientMsgsRelayed	1.3.6.1.4.1.248.12.2.11.7	Counter32	read-only	The number of UDP messages relayed to a server.
hm2AgentSwitchIpHelperAddressTable	1.3.6.1.4.1.248.12.2.11.8		not-accessible	Contains a list of IP helper addresses configured globally.
hm2AgentSwitchIpHelperAddressEntry	1.3.6.1.4.1.248.12.2.11.8.1		not-accessible	An IP Helper address that applies to packets received on any interface.
U32 hm2AgentSwitchIpHelperUdpPort	1.3.6.1.4.1.248.12.2.11.8.1.1	Unsigned32	read-write	UDP port number. A relay entry with port 0 allows dhcp, time, winnameserver, tacacs, dns, tftp, netbios-ns and netbios-dgm relay.
IP hm2AgentSwitchIpHelperAddress	1.3.6.1.4.1.248.12.2.11.8.1.2	IpAddress	read-write	The IP Helper address assigned to this interface.
U32 hm2AgentSwitchIpHelperHitCount	1.3.6.1.4.1.248.12.2.11.8.1.3	Unsigned32	read-only	The number of times a packet has been forwarded or discarded according to this entry.
ROW hm2AgentSwitchIpHelperStatus	1.3.6.1.4.1.248.12.2.11.8.1.4	RowStatus	read-create	Creates a new entry in the global IP Helper address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.
C32 hm2AgentUdpClientMsgsTtlExpired	1.3.6.1.4.1.248.12.2.11.9	Counter32	read-only	The number of UDP messages received with an expired TTL.
C32 hm2AgentUdpClientMsgsDiscarded	1.3.6.1.4.1.248.12.2.11.10	Counter32	read-only	The number of UDP messages that matched a discard entry.
hm2AgentInternalVlanGroup	1.3.6.1.4.1.248.12.2.12
VLA hm2AgentInternalVlanBase	1.3.6.1.4.1.248.12.2.12.1	VlanId	read-write	The VLAN ID internally assigned to the first port-based routing interface.
INT hm2AgentInternalVlanPolicy	1.3.6.1.4.1.248.12.2.12.2	INTEGER	read-write	Whether to search up or down from the base VLAN ID for a free VLAN ID to assign to a port-based routing interface.
hm2AgentSwitchInternalVlanTable	1.3.6.1.4.1.248.12.2.12.3		not-accessible	Contains a list of VLAN IDs used internally for port-based routing interfaces.
hm2AgentSwitchInternalVlanEntry	1.3.6.1.4.1.248.12.2.12.3.1		not-accessible	A VLAN ID internally assigned to a port-based routing interface.
VLA hm2AgentSwitchInternalVlanId	1.3.6.1.4.1.248.12.2.12.3.1.1	VlanId	not-accessible	A VLAN ID internally assigned to a port-based routing interface.
NUM hm2AgentSwitchInternalVlanIfIndex	1.3.6.1.4.1.248.12.2.12.3.1.2	InterfaceIndex	read-only	Interface index of port-based routing interface using this VLAN ID.
hm2AgentOspfQueueGroup	1.3.6.1.4.1.248.12.2.13
hm2AgentOspfQueueTable	1.3.6.1.4.1.248.12.2.13.1		not-accessible	Table lists information about OSPFv2 message queue utilization.
hm2AgentOspfQueueEntry	1.3.6.1.4.1.248.12.2.13.1.1		not-accessible	Information on a specific OSPFv2 message queue.
U32 hm2AgentOspfQueueIndex	1.3.6.1.4.1.248.12.2.13.1.1.1	Unsigned32	not-accessible	Index value for this message queue.
STR hm2AgentOspfQueueName	1.3.6.1.4.1.248.12.2.13.1.1.2	DisplayString	read-only	Name of an OSPFv2 message queue.
G32 hm2AgentOspfQueueLength	1.3.6.1.4.1.248.12.2.13.1.1.3	Gauge32	read-only	The number of messages currently in the message queue.
G32 hm2AgentOspfQueueHigh	1.3.6.1.4.1.248.12.2.13.1.1.4	Gauge32	read-only	The high water mark of the number of messages in the message queue.
C32 hm2AgentOspfQueueDrops	1.3.6.1.4.1.248.12.2.13.1.1.5	Counter32	read-only	The number of items dropped because the message queue was full.
U32 hm2AgentOspfQueueLimit	1.3.6.1.4.1.248.12.2.13.1.1.6	Unsigned32	read-only	The maximum number of messages this queue can hold.
hm2AgentOspfPacketStatsGroup	1.3.6.1.4.1.248.12.2.14
U32 hm2AgentOspfCountersCleared	1.3.6.1.4.1.248.12.2.14.1	Unsigned32	read-only	The time since OSPFv2 counters were last cleared, in seconds.
C32 hm2AgentOspfLsaRetxCount	1.3.6.1.4.1.248.12.2.14.2	Counter32	read-only	The total number of LSAs retransmitted since OSPF counters were last cleared. If the same LSA is retransmitted to multiple neighbors, the count is incremented for each neighbor.
C32 hm2AgentOspfHellosRx	1.3.6.1.4.1.248.12.2.14.3	Counter32	read-only	The total number of OSPFv2 Hello packets received since OSPF counters were last cleared.
C32 hm2AgentOspfHellosTx	1.3.6.1.4.1.248.12.2.14.4	Counter32	read-only	The total number of OSPFv2 Hello packets transmitted since OSPF counters were last cleared.
C32 hm2AgentOspfDdRx	1.3.6.1.4.1.248.12.2.14.5	Counter32	read-only	The total number of OSPFv2 Database Description packets received since OSPF counters were last cleared.
C32 hm2AgentOspfDdTx	1.3.6.1.4.1.248.12.2.14.6	Counter32	read-only	The total number of OSPFv2 Database Description packets transmitted since OSPF counters were last cleared.
C32 hm2AgentOspfLsReqRx	1.3.6.1.4.1.248.12.2.14.7	Counter32	read-only	The total number of OSPFv2 LS Request packets received since OSPF counters were last cleared.
C32 hm2AgentOspfLsReqTx	1.3.6.1.4.1.248.12.2.14.8	Counter32	read-only	The total number of OSPFv2 LS Request packets transmitted since OSPF counters were last cleared.
C32 hm2AgentOspfLsUpdatesRx	1.3.6.1.4.1.248.12.2.14.9	Counter32	read-only	The total number of OSPFv2 LS Update packets received since OSPF counters were last cleared.
C32 hm2AgentOspfLsUpdatesTx	1.3.6.1.4.1.248.12.2.14.10	Counter32	read-only	The total number of OSPFv2 LS Update packets transmitted since OSPF counters were last cleared.
C32 hm2AgentOspfLsAckRx	1.3.6.1.4.1.248.12.2.14.11	Counter32	read-only	The total number of OSPFv2 LS Acknowledgement packets received since OSPF counters were last cleared.
C32 hm2AgentOspfLsAckTx	1.3.6.1.4.1.248.12.2.14.12	Counter32	read-only	The total number of OSPFv2 LS Acknowledgement packets transmitted since OSPF counters were last cleared.
G32 hm2AgentOspfLsUpdatesRxMax	1.3.6.1.4.1.248.12.2.14.13	Gauge32	read-only	The maximum rate of OSPFv2 LS Update packets received over any 5-second interval since OSPF counters were last cleared. The rate is given in packets per second (that is, the number of packets received during the 5-second interval, divided by 5).
G32 hm2AgentOspfLsUpdatesTxMax	1.3.6.1.4.1.248.12.2.14.14	Gauge32	read-only	The maximum rate of OSPFv2 LS Update packets transmitted over any 5-second interval since OSPF counters were last cleared. The rate is given in packets per second (that is, the number of packets transmitted during the 5-second interval, divided by 5).
C32 hm2AgentOspfType1LsasRx	1.3.6.1.4.1.248.12.2.14.15	Counter32	read-only	The number of type 1 (router) LSAs received since OSPF counters were last cleared.
C32 hm2AgentOspfType2LsasRx	1.3.6.1.4.1.248.12.2.14.16	Counter32	read-only	The number of type 2 (network) LSAs received since OSPF counters were last cleared.
C32 hm2AgentOspfType3LsasRx	1.3.6.1.4.1.248.12.2.14.17	Counter32	read-only	The number of type 3 (network summary) LSAs received since OSPF counters were last cleared.
C32 hm2AgentOspfType4LsasRx	1.3.6.1.4.1.248.12.2.14.18	Counter32	read-only	The number of type 4 (ASBR summary) LSAs received since OSPF counters were last cleared.
C32 hm2AgentOspfType5LsasRx	1.3.6.1.4.1.248.12.2.14.19	Counter32	read-only	The number of type 5 (external) LSAs received since OSPF counters were last cleared.
C32 hm2AgentOspfType7LsasRx	1.3.6.1.4.1.248.12.2.14.20	Counter32	read-only	The number of type 7 (NSSA external) LSAs received since OSPF counters were last cleared.
C32 hm2AgentOspfType9LsasRx	1.3.6.1.4.1.248.12.2.14.21	Counter32	read-only	The number of type 9 (Link Opaque) LSAs received since OSPF counters were last cleared.
C32 hm2AgentOspfType10LsasRx	1.3.6.1.4.1.248.12.2.14.22	Counter32	read-only	The number of type 10 (Area Opaque) LSAs received since OSPF counters were last cleared.
C32 hm2AgentOspfType11LsasRx	1.3.6.1.4.1.248.12.2.14.23	Counter32	read-only	The number of type 11 (AS Opaque) LSAs received since OSPF counters were last cleared.
hm2AgentOspfSpfStatsTable	1.3.6.1.4.1.248.12.2.15		not-accessible	Contains statistics for the twenty most recent SPF runs. Statistics are reported from the oldest SPF first to the most recent.
hm2AgentOspfSpfStatsEntry	1.3.6.1.4.1.248.12.2.15.1		not-accessible	Statistics for a single SPF run.
U32 hm2AgentOspfSpfIndex	1.3.6.1.4.1.248.12.2.15.1.1	Unsigned32	not-accessible	Integer that uniquely identifies an SPF run. This value is incremented each time OSPF runs a full routing table calculation.
U32 hm2AgentOspfSpfStatsDeltaT	1.3.6.1.4.1.248.12.2.15.1.2	Unsigned32	read-only	How long since this routing table calculation ran. The time is given in seconds.
U32 hm2AgentOspfSpfStatsIntra	1.3.6.1.4.1.248.12.2.15.1.3	Unsigned32	read-only	Number of milliseconds to compute intra-area routes.
U32 hm2AgentOspfSpfStatsSumm	1.3.6.1.4.1.248.12.2.15.1.4	Unsigned32	read-only	Number of milliseconds to compute inter-area routes.
U32 hm2AgentOspfSpfStatsExt	1.3.6.1.4.1.248.12.2.15.1.5	Unsigned32	read-only	Number of milliseconds to compute external routes.
U32 hm2AgentOspfSpfStatsSpfTotal	1.3.6.1.4.1.248.12.2.15.1.6	Unsigned32	read-only	Number of milliseconds for entire routing table calculation.
U32 hm2AgentOspfSpfStatsRibUpdate	1.3.6.1.4.1.248.12.2.15.1.7	Unsigned32	read-only	Number of milliseconds to update the common routing table.
STR hm2AgentOspfSpfStatsReason	1.3.6.1.4.1.248.12.2.15.1.8	DisplayString	read-only	Reasons why a routing table calculation was required. R - new router LSA, N - new Network LSA, SN - new network summary LSA, SA - new ASBR summary LSA, X - new external LSA.
hm2AgentRoutingHeapGroup	1.3.6.1.4.1.248.12.2.16
U32 hm2AgentRoutingHeapSize	1.3.6.1.4.1.248.12.2.16.1	Unsigned32	read-only	The size of the routing heap, in bytes. Unicast routing protocols and ARP allocate memory from the routing heap.
G32 hm2AgentRoutingHeapInUse	1.3.6.1.4.1.248.12.2.16.2	Gauge32	read-only	The number of bytes currently allocated from the routing heap.
G32 hm2AgentRoutingHeapHigh	1.3.6.1.4.1.248.12.2.16.3	Gauge32	read-only	High water mark for the number of bytes allocated from the routing heap.
hm2AgentRoutingTableSummaryGroup	1.3.6.1.4.1.248.12.2.17
G32 hm2AgentConnectedRoutes	1.3.6.1.4.1.248.12.2.17.1	Gauge32	read-only	The number of connected routes in the IPv4 routing table.
G32 hm2AgentStaticRoutes	1.3.6.1.4.1.248.12.2.17.2	Gauge32	read-only	The number of static routes in the IPv4 routing table.
G32 hm2AgentRipRoutes	1.3.6.1.4.1.248.12.2.17.3	Gauge32	read-only	The number of RIP routes in the IPv4 routing table.
G32 hm2AgentOspfRoutes	1.3.6.1.4.1.248.12.2.17.4	Gauge32	read-only	The number of OSPFv2 routes in the IPv4 routing table.
G32 hm2AgentOspfIntraRoutes	1.3.6.1.4.1.248.12.2.17.5	Gauge32	read-only	The number of OSPFv2 intra-area routes in the IPv4 routing table.
G32 hm2AgentOspfInterRoutes	1.3.6.1.4.1.248.12.2.17.6	Gauge32	read-only	The number of OSPFv2 inter-area routes in the IPv4 routing table.
G32 hm2AgentOspfExt1Routes	1.3.6.1.4.1.248.12.2.17.7	Gauge32	read-only	The number of OSPFv2 external type 1 routes in the IPv4 routing table.
G32 hm2AgentOspfExt2Routes	1.3.6.1.4.1.248.12.2.17.8	Gauge32	read-only	The number of OSPFv2 external type 2 routes in the IPv4 routing table.
G32 hm2AgentBgpRoutes	1.3.6.1.4.1.248.12.2.17.9	Gauge32	read-only	The number of BGP routes in the IPv4 routing table.
G32 hm2AgentEbgpRoutes	1.3.6.1.4.1.248.12.2.17.10	Gauge32	read-only	The number of external BGP routes in the IPv4 routing table.
G32 hm2AgentIbgpRoutes	1.3.6.1.4.1.248.12.2.17.11	Gauge32	read-only	The number of internal BGP routes in the IPv4 routing table.
G32 hm2AgentLocalBgpRoutes	1.3.6.1.4.1.248.12.2.17.12	Gauge32	read-only	The number of local BGP routes in the IPv4 routing table.
G32 hm2AgentRejectRoutes	1.3.6.1.4.1.248.12.2.17.13	Gauge32	read-only	The number of reject routes in the IPv4 routing table.
G32 hm2AgentTotalRoutes	1.3.6.1.4.1.248.12.2.17.14	Gauge32	read-only	The number of routes in the IPv4 routing table.
G32 hm2AgentBestRoutes	1.3.6.1.4.1.248.12.2.17.15	Gauge32	read-only	The number of IPv4 routes in the forwarding table.
G32 hm2AgentBestRoutesHigh	1.3.6.1.4.1.248.12.2.17.16	Gauge32	read-only	The highest number of IPv4 routes in the forwarding table.
G32 hm2AgentAlternateRoutes	1.3.6.1.4.1.248.12.2.17.17	Gauge32	read-only	The number of alternate routes in the IPv4 routing table. An alternate route is less preferred than the best route and is not used for forwarding.
C32 hm2AgentRouteAdds	1.3.6.1.4.1.248.12.2.17.18	Counter32	read-only	The number of routes added to the IPv4 routing table.
C32 hm2AgentRouteModifies	1.3.6.1.4.1.248.12.2.17.19	Counter32	read-only	The number of routes changed in the IPv4 routing table.
C32 hm2AgentRouteDeletes	1.3.6.1.4.1.248.12.2.17.20	Counter32	read-only	The number of routes removed from the IPv4 routing table.
C32 hm2AgentUnresolvedRouteAdds	1.3.6.1.4.1.248.12.2.17.21	Counter32	read-only	The number of IPv4 route adds that failed because none of the route's next hops were on a local subnet.
C32 hm2AgentInvalidRouteAdds	1.3.6.1.4.1.248.12.2.17.22	Counter32	read-only	The number of IPv4 routes adds that failed because the route was invalid.
C32 hm2AgentFailedRouteAdds	1.3.6.1.4.1.248.12.2.17.23	Counter32	read-only	The number of IPv4 routes adds that failed because of a resource limitation in the routing table
G32 hm2AgentReservedLocals	1.3.6.1.4.1.248.12.2.17.24	Gauge32	read-only	The number of IPv4 routing table entries reserved for a local subnet on a routing interface that is down.
G32 hm2AgentUniqueNextHops	1.3.6.1.4.1.248.12.2.17.25	Gauge32	read-only	The number of distinct next hops used among all IPv4 routes currently in the routing table. These include local interfaces for local routes and neighbors for indirect routes.
G32 hm2AgentUniqueNextHopsHigh	1.3.6.1.4.1.248.12.2.17.26	Gauge32	read-only	The highest count of unique next hops since counters were last cleared.
G32 hm2AgentNextHopGroups	1.3.6.1.4.1.248.12.2.17.27	Gauge32	read-only	The current number of next hop groups in use by one or more routes. Each next hop group includes one or more next hops.
G32 hm2AgentNextHopGroupsHigh	1.3.6.1.4.1.248.12.2.17.28	Gauge32	read-only	The highest count of next hop groups since counters were last cleared.
G32 hm2AgentEcmpGroups	1.3.6.1.4.1.248.12.2.17.29	Gauge32	read-only	The number of next hop groups with multiple next hops.
G32 hm2AgentEcmpGroupsHigh	1.3.6.1.4.1.248.12.2.17.30	Gauge32	read-only	The high water mark of the number of ECMP groups.
G32 hm2AgentEcmpRoutes	1.3.6.1.4.1.248.12.2.17.31	Gauge32	read-only	The current number of IPv4 routes with multiple next hops.
G32 hm2AgentTruncEcmpRoutes	1.3.6.1.4.1.248.12.2.17.32	Gauge32	read-only	The number of ECMP routes that are currently installed in the forwarding table with just one next hop. The forwarding table may limit the number of ECMP routes or the number of ECMP groups. When an ECMP route cannot be installed because such a limit is reached, the route is installed with a single next hop.
C32 hm2AgentEcmpRetries	1.3.6.1.4.1.248.12.2.17.33	Counter32	read-only	The number of ECMP routes that have been installed in the forwarding table after initially being installed with a single next hop.
hm2AgentEcmpCountTable	1.3.6.1.4.1.248.12.2.18		not-accessible	A count of the number of routes with each number of ECMP next hops.
hm2AgentEcmpCountEntry	1.3.6.1.4.1.248.12.2.18.1		not-accessible	Number of IPv4 routes with a given number of next hops.
U32 hm2AgentEcmpNextHopCount	1.3.6.1.4.1.248.12.2.18.1.1	Unsigned32	not-accessible	The number of next hops in a route. From 0 to the maximum number of next hops in an ECMP route. The maximum varies by platform.
G32 hm2AgentEcmpRouteCount	1.3.6.1.4.1.248.12.2.18.1.2	Gauge32	read-only	The number of IPv4 routes with agentEcmpNextHopCount next hops.
hm2AgentOspfStubRouterGroup	1.3.6.1.4.1.248.12.2.19
INT hm2AgentOspfStubRouterAdvertisement	1.3.6.1.4.1.248.12.2.19.1	INTEGER	read-only	Specifies how the router LSAs are advertised by the router. The value doNotAdvertise indicates the advertisement of a standard router LSA and is the default value. The value advertise indicates the advertisement of a stub router LSA.
INT hm2AgentOspfStubRouterReason	1.3.6.1.4.1.248.12.2.19.2	INTEGER	read-only	This indicates the reason because of which the router is in Stub mode. This is valid only if the agentOspfStubRouterMode is 'active'.
U32 hm2AgentOspfStubRouterStartupTimeRemaining	1.3.6.1.4.1.248.12.2.19.3	Unsigned32	read-only	The time remaining (in seconds) for the router to come out of the stub mode. This is valid only if the agentOspfStubRouterReason is 'startup'.
U32 hm2AgentOspfStubRouterDuration	1.3.6.1.4.1.248.12.2.19.4	Unsigned32	read-only	Time elapsed (in seconds) since the router last entered the stub router mode. This is valid only if the agentOspfStubRouterMode is 'active' and agentOspfStubRouterReason is 'resource-limitation'.
hm2AgentOspfNbrTable	1.3.6.1.4.1.248.12.2.249		not-accessible	Information about this router's neighbors. Augments ospfNbrTable from the OSPF-MIB.
hm2AgentOspfNbrEntry	1.3.6.1.4.1.248.12.2.249.1		not-accessible	Information about a single neighbor. Augments ospfNbrEntry in OSPF-MIB.
TIK hm2AgentOspfNbrDeadTime	1.3.6.1.4.1.248.12.2.249.1.1	TimeTicks	read-only	The neighbor's Dead Time is the amount of remaining time since the last OSPF hello packet received, before declaring the neighbor status as down.
hm2AgentOspfRouteTable	1.3.6.1.4.1.248.12.2.250		not-accessible	Information about this router's OSPF routes.
hm2AgentOspfRouteEntry	1.3.6.1.4.1.248.12.2.250.1		not-accessible	Information about a single route.
ADR hm2AgentOspfRouteNet	1.3.6.1.4.1.248.12.2.250.1.1	InetAddressIPv4	not-accessible	The IP Address of the Net or Subnet indicated by the route.
ADR hm2AgentOspfRouteMask	1.3.6.1.4.1.248.12.2.250.1.2	InetAddressIPv4	not-accessible	The Subnet Mask that pertains to the Net or Subnet.
I32 hm2AgentOspfRouteCost	1.3.6.1.4.1.248.12.2.250.1.3	Integer32	read-only	The route cost calculated in the SPF algorithm to reach the network.
INT hm2AgentOspfRouteProtoType	1.3.6.1.4.1.248.12.2.250.1.4	INTEGER	read-only	The type of route that was learned from OSPF.
hm2AgentVrrpExtGroup	1.3.6.1.4.1.248.12.2.260
hm2AgentVrrpTrackingTable	1.3.6.1.4.1.248.12.2.260.1		not-accessible	This table contains variables to define an entry in the VRRP Tracking database.
hm2AgentVrrpTrackingEntry	1.3.6.1.4.1.248.12.2.260.1.1		not-accessible	The entries of the table.
I32 hm2AgentVrrpTrackIfIndex	1.3.6.1.4.1.248.12.2.260.1.1.1	Integer32	not-accessible	DURABLE: { 1:all } The interface number of the virtual router
I32 hm2AgentVrrpTrackVrid	1.3.6.1.4.1.248.12.2.260.1.1.2	Integer32	not-accessible	DURABLE: { 1:all } The virtual router id for this virtual router
STR hm2AgentVrrpTrackId	1.3.6.1.4.1.248.12.2.260.1.1.3	SnmpAdminString	not-accessible	DURABLE: { 1:all } The id of the object being tracked
I32 hm2AgentVrrpTrackDecrement	1.3.6.1.4.1.248.12.2.260.1.1.4	Integer32	read-write	DURABLE: { 1:all } The value by wich the current priority of the virtual router is decremented when the tracked object goes DOWN.
INT hm2AgentVrrpTrackOperStatus	1.3.6.1.4.1.248.12.2.260.1.1.5	INTEGER	read-only	Shows if the tracked object is currently UP or DOWN or NOT-READY
ROW hm2AgentVrrpTrackRowStatus	1.3.6.1.4.1.248.12.2.260.1.1.6	RowStatus	read-create	DURABLE: { 1:all } Defines the status of a vrrp tracking database entry. Set to createAndGo(4) to create a new row. Set to destroy(6) to delete an entry. Reads as active(1) if the tracked object exists and is trackable, notReady(3) otherwise.
hm2AgentVrrpExtTable	1.3.6.1.4.1.248.12.2.260.2		not-accessible	This table contains variables to define an entry in the VRRP enhancements database.
hm2AgentVrrpExtEntry	1.3.6.1.4.1.248.12.2.260.2.1		not-accessible	The entry of the hm2AgentVrrpExtTable.
I32 hm2AgentVrrpExtIfIndex	1.3.6.1.4.1.248.12.2.260.2.1.1	Integer32	not-accessible	The interface number of the virtual router
I32 hm2AgentVrrpExtVrid	1.3.6.1.4.1.248.12.2.260.2.1.2	Integer32	not-accessible	The virtual router id for this virtual router
I32 hm2AgentVrrpExtDomainId	1.3.6.1.4.1.248.12.2.260.2.1.3	Integer32	read-write	The domain this virtual router is a member of. If set to 0, the virtual router is not a member of any domain.
INT hm2AgentVrrpExtDomainRole	1.3.6.1.4.1.248.12.2.260.2.1.4	INTEGER	read-write	The role of this virtual router in its domain. This is none(1) if the virtual router is not member of a domain, supervisor(3) if it is the supervisor of its domain, member(2) otherwise.
INT hm2AgentVrrpExtDomainStatus	1.3.6.1.4.1.248.12.2.260.2.1.5	INTEGER	read-only	Shows if the domain configuration is correct for this virtual router
IP hm2AgentVrrpExtAdvertAddress	1.3.6.1.4.1.248.12.2.260.2.1.6	IpAddress	read-write	The IP address advertisements of the virtual router are sent to
I32 hm2AgentVrrpExtAdvertTimer	1.3.6.1.4.1.248.12.2.260.2.1.7	Integer32	read-write	This is used to set the interval between advertisements in milliseconds. This accesses the same value as vrrpOperAdvertisementInterval.
I32 hm2AgentVrrpExtCfgPriority	1.3.6.1.4.1.248.12.2.260.2.1.8	Integer32	read-write	The configured priority of the virtual router. This can be different from the operating priority if tracked objects are down or the virtual router is the ip address owner
IP hm2AgentVrrpExtNotifyAddress	1.3.6.1.4.1.248.12.2.260.2.1.9	IpAddress	read-write	The IP address notifications of the virtual router are sent to
HME hm2AgentVrrpExtNotifyLinkdown	1.3.6.1.4.1.248.12.2.260.2.1.10	HmEnabledStatus	read-write	Enables or disables sending of notification messages if the virtual router's interface goes down.
I32 hm2AgentVrrpExtPreemptionDelay	1.3.6.1.4.1.248.12.2.260.2.1.11	Integer32	read-write	Time (in seconds) after startup of the virtual router by which the preemption of a Master with a lower priority is delayed.
IP hm2AgentVrrpPrimaryVirtualAddress	1.3.6.1.4.1.248.12.2.260.2.1.12	IpAddress	read-only	The virtual IP address in the subnet of the primary ip address on the interface. If no match is found, an unspecified virtual address is returned. If no virtual address is configured, 0.0.0.0 is returned.
INT hm2AgentVrrpExtMethod	1.3.6.1.4.1.248.12.2.260.2.1.13	INTEGER	read-write	The source of the VRRP instance. User can set the object to none(1), config(2), ttdp(3).
hm2AgentVrrpDomainTable	1.3.6.1.4.1.248.12.2.260.3		not-accessible	This table contains variables to define an entry in the VRRP domain database.
hm2AgentVrrpDomainEntry	1.3.6.1.4.1.248.12.2.260.3.1		not-accessible	The entries of the table.
I32 hm2AgentVrrpDomainId	1.3.6.1.4.1.248.12.2.260.3.1.1	Integer32	not-accessible	The domain ID.
HME hm2AgentVrrpDomainMemberSendAdv	1.3.6.1.4.1.248.12.2.260.3.1.2	HmEnabledStatus	read-write	DURABLE: { 1:all } Determines if the members of this domain send advertisement packets. If set to disabled(2), only the supervisor of the domain sends packets.
INT hm2AgentVrrpDomainStatus	1.3.6.1.4.1.248.12.2.260.3.1.3	INTEGER	read-only	Shows if the configuration of the domain is complete.
I32 hm2AgentVrrpDomainSupervisorIfIndex	1.3.6.1.4.1.248.12.2.260.3.1.4	Integer32	read-only	The interface number of the supervisor of the domain
I32 hm2AgentVrrpDomainSupervisorVrid	1.3.6.1.4.1.248.12.2.260.3.1.5	Integer32	read-only	The virtual router id of the supervisor of the domain. 0 if unconfigured
I32 hm2AgentVrrpDomainOperPriority	1.3.6.1.4.1.248.12.2.260.3.1.6	Integer32	read-only	The current operating priority of the domain. This can be different from the configured priority if tracked objects are down. For domain members this is the priority of the supervisor of that Domain if the supervisor is configured and up.
INT hm2AgentVrrpDomainSupervisorOperState	1.3.6.1.4.1.248.12.2.260.3.1.7	INTEGER	read-only	Shows the current operational state of the domain supervisor.
hm2AgentNeighbourGroup	1.3.6.1.4.1.248.12.2.270
hm2AgentStaticNeighbourTable	1.3.6.1.4.1.248.12.2.270.10		not-accessible	.
hm2AgentStaticNeighbourEntry	1.3.6.1.4.1.248.12.2.270.10.1		not-accessible	.
IPt hm2AgentStaticNeighbourAddressType	1.3.6.1.4.1.248.12.2.270.10.1.1	InetAddressType	not-accessible	.
IP hm2AgentStaticNeighbourAddress	1.3.6.1.4.1.248.12.2.270.10.1.2	InetAddress	not-accessible	.
PHY hm2AgentStaticNeighbourPhysAddress	1.3.6.1.4.1.248.12.2.270.10.1.3	PhysAddress	read-create	.
NUM hm2AgentStaticNeighbourIfIndex	1.3.6.1.4.1.248.12.2.270.10.1.4	InterfaceIndexOrZero	read-only	.
ROW hm2AgentStaticNeighbourRowStatus	1.3.6.1.4.1.248.12.2.270.10.1.5	RowStatus	read-create	The status of this entry. Setting this object destroy will remove the entry.
hm2AgentDynamicNeighbourTable	1.3.6.1.4.1.248.12.2.270.11		not-accessible	.
hm2AgentDynamicNeighbourEntry	1.3.6.1.4.1.248.12.2.270.11.1		not-accessible	.
IPt hm2AgentDynamicNeighbourAddressType	1.3.6.1.4.1.248.12.2.270.11.1.1	InetAddressType	not-accessible	.
IP hm2AgentDynamicNeighbourAddress	1.3.6.1.4.1.248.12.2.270.11.1.2	InetAddress	not-accessible	.
PHY hm2AgentDynamicNeighbourPhysAddress	1.3.6.1.4.1.248.12.2.270.11.1.3	PhysAddress	read-only	.
NUM hm2AgentDynamicNeighbourIfIndex	1.3.6.1.4.1.248.12.2.270.11.1.4	InterfaceIndexOrZero	read-only	.
INT hm2AgentDynamicNeighbourAction	1.3.6.1.4.1.248.12.2.270.11.1.5	INTEGER	read-write	.
hm2AgentRoutingSNMPExtensionGroup	1.3.6.1.4.1.248.12.2.280
hm2AgentIpHelperTableFullErrorReturn	1.3.6.1.4.1.248.12.2.280.1			The maximum number of IP helper entries has been reached
hm2AgentIpHelperInvalidServerAddrErrorReturn	1.3.6.1.4.1.248.12.2.280.2			Invalid IP server address.
hm2AgentRouterOspfDependenciesNotMet	1.3.6.1.4.1.248.12.2.280.3			Cannot modify OSPF admin state on this interface. Set primary IP address.
hm2AgentRouterOspfRangeTableFullErrorReturn	1.3.6.1.4.1.248.12.2.280.4			The maximum number of area-range entries has been reached.
hm2AgentRouterOspfVirtNbrTableFullErrorReturn	1.3.6.1.4.1.248.12.2.280.5			The maximum number of virtual neighbor entries has been reached.
hm2AgentRouterRIPDependenciesNotMet	1.3.6.1.4.1.248.12.2.280.8			Cannot modify RIP admin state on this interface. Set primary IP address.
hm2AgentIpHelperInvalidUdpPortErrorReturn	1.3.6.1.4.1.248.12.2.280.9			Invalid UDP port.
hm2AgentStaticNeighbourTableFullErrorReturn	1.3.6.1.4.1.248.12.2.280.10			Static Neighbour Table is full.
hm2AgentSecondaryAddrNoPrimaryErrorReturn	1.3.6.1.4.1.248.12.2.280.11			Cannot add the secondary IP address because the interface has no primary IP address.
hm2AgentSecondaryAddrDifferentPrimaryErrorReturn	1.3.6.1.4.1.248.12.2.280.12			The secondary IP address must be different from the primary IP address.
hm2AgentSecondaryAddrWrongIpClassErrorReturn	1.3.6.1.4.1.248.12.2.280.13			The network number of the secondary IP address is not valid to be used on a routing interface.
hm2AgentSecondaryAddrWrongSubnetErrorReturn	1.3.6.1.4.1.248.12.2.280.14			All IP addresses on the interface must be from different subnets.
hm2AgentSecondaryAddrMaxIntfEntriesErrorReturn	1.3.6.1.4.1.248.12.2.280.15			The maximum number of secondary IP addresses on the interface has been reached.
hm2AgentSecondaryAddrMaxSystemEntriesErrorReturn	1.3.6.1.4.1.248.12.2.280.16			The maximum number of IP addresses on the system has been reached.
hm2AgentSecondaryAddrStaticRouteErrorReturn	1.3.6.1.4.1.248.12.2.280.17			The secondary IP address is same as the next hop address of a static route.
hm2AgentSecondaryAddrStaticARPErrorReturn	1.3.6.1.4.1.248.12.2.280.18			The secondary IP address is same as a static ARP entry.
hm2AgentSecondaryAddrAbsentEntryErrorReturn	1.3.6.1.4.1.248.12.2.280.19			The secondary IP address is not configured on the interface.
hm2AgentPrimaryAddrWrongIpClassErrorReturn	1.3.6.1.4.1.248.12.2.280.20			The primary IP address is out of the allowed IP class.
hm2AgentPrimaryAddrConflictErrorReturn	1.3.6.1.4.1.248.12.2.280.21			The primary IP address conflicts with another IP address on a routing interface.
hm2AgentPrimaryAddrStaticRouteErrorReturn	1.3.6.1.4.1.248.12.2.280.22			The primary IP address is same as the next hop address of a static route.
hm2AgentPrimaryAddrStaticARPErrorReturn	1.3.6.1.4.1.248.12.2.280.23			The primary IP address is same as a static ARP entry.
hm2AgentPrimaryAddrExistingSecondaryErrorReturn	1.3.6.1.4.1.248.12.2.280.24			The primary IP address cannot be changed because the interface has secondary IP addresses configured.
hm2AgentPrimaryAddrNetworkConflictErrorReturn	1.3.6.1.4.1.248.12.2.280.25			The primary IP address conflicts with the management IP address.
hm2AgentPrimaryAddrRoutingTableFullErrorReturn	1.3.6.1.4.1.248.12.2.280.26			The primary IP address cannot be added because there are no free entries in the routing table.
hm2AgentDstAddrHostBitSetErrorReturn	1.3.6.1.4.1.248.12.2.280.27			The route cannot be added. Host bits must not be set in the destination. Network address is {0}.
hm2AgentSamePrefRouteErrorReturn	1.3.6.1.4.1.248.12.2.280.28			Route cannot be added because reject route and next hop route cannot share the same preference.
hm2AgentVrrpAssoIpAddrRowStatusInconsistentAddress	1.3.6.1.4.1.248.12.2.280.29			The virtual address does not matching the current interface address configuration.
hm2AgentVrrpAssoIpAddrRowStatusInvalidAddress	1.3.6.1.4.1.248.12.2.280.30			The virtual address is not valid with the current interface address configuration.
hm2AgentVrrpAssoIpAddrRowStatusUnknownVRID	1.3.6.1.4.1.248.12.2.280.31			Unknown virtual router id.
hm2AgentSwitchIpRouterDiscMinMaxAdvtIntErrorRtrn	1.3.6.1.4.1.248.12.2.280.32			Min advertisement interval is bigger then max advertisement interval.
hm2AgentSwitchIpRouterDiscLifeTimeMaxAdvIntErrorRtrn	1.3.6.1.4.1.248.12.2.280.33			Max advertisement interval is bigger then advertisement life time.
hm2AgentSwitchIpIcmpRateLimitExceedingRatioErrorReturn	1.3.6.1.4.1.248.12.2.280.34			Rate limit ratio exceeds 100 packets per second.
hm2AgentRouterOspfMaxAreaErrorReturn	1.3.6.1.4.1.248.12.2.280.35			The maximum number of OSPF areas has been reached.
hm2AgentospfRouterIdChange	1.3.6.1.4.1.248.12.2.280.36			OSPF must be disabled to change the router ID.
hm2AgentOspfRedistDistList	1.3.6.1.4.1.248.12.2.280.37			Please add a redistribute list.
hm2AgentOspfDefaultAreaDeleteErrorReturn	1.3.6.1.4.1.248.12.2.280.38			The default area cannot be deleted.
hm2AgentLocalArpDeleteErrorReturn	1.3.6.1.4.1.248.12.2.280.39			Local ARP entries cannot be deleted.
hm2AgentDynamicVlanRoutingErrorReturn	1.3.6.1.4.1.248.12.2.280.40			Dynamic VLANs cannot be used for routing interfaces.

RFC description

Huawei platform MIB for managing and monitoring routing-related metrics on network devices. Tracks routing table statistics including number of unique next hops and route management information.

Start monitoring Hirschmann HiOS Platform2 industrial switch (Layer 3 routing) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HM2-PLATFORM-ROUTING-MIB