H3C-VODIALCONTROL-MIB

All MIBs › H3C-VODIALCONTROL-MIB

Organization: Huawei-3COM Technologies Co., Ltd.

Last Updated: 2005-03-15

Category: Domain: VoIP/Telephony, Vendor: H3C/HH3C

Description: Covers voice dial control on H3C equipment, including dial peers, call routing rules, and voice traffic engineering.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is H3C-VODIALCONTROL-MIB?

H3C-VODIALCONTROL-MIB is an H3C-proprietary MIB covering voice dial control configuration, managing dial peers, call routing rules, and voice traffic engineering on H3C voice-enabled routers and gateways. It exposes configuration objects that define how calls are matched to dial peers and routed across voice trunks, which is primarily a software/configuration-status domain rather than physical hardware telemetry. Monitoring value centers on the operational state of dial-peer routing rules and call-handling configuration, useful for diagnosing call-setup failures or misrouted calls. It likely depends on or parallels concepts from standard voice/telephony MIBs (e.g., dial control MIB conventions) even though it is vendor-specific. It is deployed in H3C VoIP gateway and unified-communications environments where voice trunking needs to be centrally managed via SNMP. Engineers can download the H3C-VODIALCONTROL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in H3C-VODIALCONTROL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C VoIP gateways and routers

Monitoring Examples

Without sample_objects provided for this module, no specific table or object names can be cited from the source; a plausible scenario, consistent with the module description, would be polling dial-peer configuration entries to confirm a peer's routing rule and destination pattern match expected call flows. An admin troubleshooting failed call setups would check whether the dial-peer table reflects the intended routing configuration.

What Can Be Monitored

dial peer configuration
call routing rules
voice trunk configuration

Imported Objects

From H3C-VO-TYPE-MIB

CodecType

From HUAWEI-3COM-OID-MIB

h3cVoice

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
h3cVoiceDialControl	1.3.6.1.4.1.2011.10.2.39.5			This MIB file is to provide the definition of voice dial control configuration.
h3cVoPeerObjects	1.3.6.1.4.1.2011.10.2.39.5.1
h3cVoPeerCommonConfigTable	1.3.6.1.4.1.2011.10.2.39.5.1.1		not-accessible	This table contains the general voice peer information.
h3cVoPeerCommonConfigEntry	1.3.6.1.4.1.2011.10.2.39.5.1.1.1		not-accessible	The entry of h3cVoPeerCommonConfigTable.
I32 h3cVoPeerCfgIndex	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.1	Integer32	not-accessible	The index of a dial entity common table.
ROW h3cVoPeerCfgRowStatus	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.2	RowStatus	read-create	This object is used to create, delete or modify a row in this table.
INT h3cVoPeerCfgType	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.3	INTEGER	read-create	The type of voice entity.
OCT h3cVoPeerCfgDesPattern	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.4	OCTET STRING	read-create	This object indicates the caller number of this dial peer.
COD h3cVoPeerCfgCodec1st	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.5	CodecType	read-create	This object indicates the first desirable CODEC of speech of this dial peer.
COD h3cVoPeerCfgCodec2nd	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.6	CodecType	read-create	This object indicates the second desirable CODEC of speech of this dial peer.
COD h3cVoPeerCfgCodec3rd	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.7	CodecType	read-create	This object indicates the third desirable CODEC of speech of this dial peer.
COD h3cVoPeerCfgCodec4th	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.8	CodecType	read-create	This object indicates the forth desirable CODEC of speech of this dial peer.
I32 h3cVoPeerCfgDSCP	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.9	Integer32	read-create	This object indicates the DSCP(Different Service Code Point) value of voice packets.
INT h3cVoPeerCfgShutDown	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.10	INTEGER	read-create	This object indicates the current status of this dial peer.
INT h3cVoPeerCfgVADEnable	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.11	INTEGER	read-create	This object indicates whether the VAD(Voice Activity Detection) is enabled.
INT h3cVoPeerCfgOutbandMode	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.12	INTEGER	read-create	This object indicates the DTMF(Dual Tone Multi-Frequency) outband type of this dial peer.
I32 h3cVoPeerCfgFaxLevel	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.13	Integer32	read-create	This object indicates the fax level of this dial peer.
FAX h3cVoPeerCfgFaxBaudrate	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.14	FaxBaudrateType	read-create	This object indicates the fax baudrate of this dial peer.
I32 h3cVoPeerCfgFaxLocalTrainPara	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.15	Integer32	read-create	This object indicates the fax local train threshold of this dial peer.
FAX h3cVoPeerCfgFaxProtocol	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.16	FaxProtocolType	read-create	This object indicates the fax protocol of this dial peer.
I32 h3cVoPeerCfgT38FaxHRPackNum	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.17	Integer32	read-create	This object indicates the high speed redundancy packet numbers.
I32 h3cVoPeerCfgT38FaxLRPackNum	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.18	Integer32	read-create	This object indicates the low speed redundancy packet numbers.
INT h3cVoPeerCfgFaxSendNSFEnable	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.19	INTEGER	read-create	This object indicates whether sends NSF(non-standard faculty) to fax of this dial peer.
FAX h3cVoPeerCfgFaxSupportMode	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.20	FaxSupportModeType	read-create	This object indicates the fax support mode of this dial peer.
FAX h3cVoPeerCfgFaxTrainMode	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.21	FaxTrainMode	read-create	This object indicates the fax train mode of this dial peer.
INT h3cVoPeerCfgFaxEcm	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.22	INTEGER	read-create	This object indicates whether the ECM(error correct mode) is enabled.
I32 h3cVoPeerCfgPriority	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.23	Integer32	read-create	This object indicates the priority of this dial peer.
OCT h3cVoPeerCfgDescription	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.24	OCTET STRING	read-create	This object indicates the textual description of this dial peer.
PHO h3cVoPeerCfgCallingNumberType	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.25	PhoneNumberType	read-create	This object indicates the type of calling number of this dial peer.
PHO h3cVoPeerCfgCalledNumberType	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.26	PhoneNumberType	read-create	This object indicates the type of called number of this dial peer.
PHO h3cVoPeerCfgCallingNumberPlan	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.27	PhoneNumberPlan	read-create	This object indicates the numbering plan of calling number of this dial peer.
PHO h3cVoPeerCfgCalledNumberPlan	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.28	PhoneNumberPlan	read-create	This object indicates the numbering plan of called number of this dial peer.
INT h3cVoPeerCfgSelectStop	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.29	INTEGER	read-create	This object indicates whether permitting the system to allocate alternative entities to establish a phone call.
I32 h3cVoPeerCfgCallingNumSubstRule	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.30	Integer32	read-create	This object indicates number-substitute rule of calling number.
I32 h3cVoPeerCfgCalledNumSubstRule	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.31	Integer32	read-create	This object indicates number-substitute rule of called number.
I32 h3cVoPeerCfgMaxCall	1.3.6.1.4.1.2011.10.2.39.5.1.1.1.32	Integer32	read-create	The object indicates that this dial peer is bound with a tag that indicates a maximum call value.
h3cVoPOTSPeerConfigTable	1.3.6.1.4.1.2011.10.2.39.5.1.2		not-accessible	This table contains the POTS(Public Switched Telephone Network) peer information.
h3cVoPOTSPeerConfigEntry	1.3.6.1.4.1.2011.10.2.39.5.1.2.1		not-accessible	The entry of h3cVoPOTSPeerConfigTable.
I32 h3cVoPOTSPeerConfigIndex	1.3.6.1.4.1.2011.10.2.39.5.1.2.1.1	Integer32	not-accessible	The index of voice pots peer table.
OCT h3cVoPOTSPeerConfigPrefix	1.3.6.1.4.1.2011.10.2.39.5.1.2.1.2	OCTET STRING	read-write	This object indicates the prefix which is added to the called number.
OCT h3cVoPOTSPeerConfigSubLine	1.3.6.1.4.1.2011.10.2.39.5.1.2.1.3	OCTET STRING	read-write	This object indicates the voice subscriber line of this dial peer.
I32 h3cVoPOTSPeerConfigSendNum	1.3.6.1.4.1.2011.10.2.39.5.1.2.1.4	Integer32	read-write	This object indicates the digit of phone number to be sent to the destination.
h3cVoVoIPPeerConfigTable	1.3.6.1.4.1.2011.10.2.39.5.1.3		not-accessible	This table contains the voip peer information.
h3cVoVoIPPeerConfigEntry	1.3.6.1.4.1.2011.10.2.39.5.1.3.1		not-accessible	The entry of h3cVoVoIPPeerConfigTable.
I32 h3cVoVoIPPeerCfgIndex	1.3.6.1.4.1.2011.10.2.39.5.1.3.1.1	Integer32	not-accessible	The index of voice voip peer table.
INT h3cVoVoIPPeerCfgTargetType	1.3.6.1.4.1.2011.10.2.39.5.1.3.1.2	INTEGER	read-write	This object indicates the type of the session target of this peer.
IPt h3cVoVoIPPeerCfgTargetAddrType	1.3.6.1.4.1.2011.10.2.39.5.1.3.1.3	InetAddressType	read-write	The IP address type of object h3cVoVoIPPeerCfgTargetAddr.
IP h3cVoVoIPPeerCfgTargetAddr	1.3.6.1.4.1.2011.10.2.39.5.1.3.1.4	InetAddress	read-write	This object indicates the target ip address. This object is valid when h3cVoVoIPPeerCfgTargetType is h323Ipv4 or sipIpv4.
INT h3cVoVoIPPeerCfgFastStart	1.3.6.1.4.1.2011.10.2.39.5.1.3.1.5	INTEGER	read-write	This object indicates whether the fast connection function is enabled.
INT h3cVoVoIPPeerCfgTunnel	1.3.6.1.4.1.2011.10.2.39.5.1.3.1.6	INTEGER	read-write	This object indicates whether the tunnel function is enabled.
OCT h3cVoVoIPPeerCfgAreaID	1.3.6.1.4.1.2011.10.2.39.5.1.3.1.7	OCTET STRING	read-write	This object specifies service area-id.
INT h3cVoVoIPPeerCfgSendRing	1.3.6.1.4.1.2011.10.2.39.5.1.3.1.8	INTEGER	read-write	This object indicates whether sending ring is enabled.
h3cVoPeerDefaultConfigObjects	1.3.6.1.4.1.2011.10.2.39.5.1.4
COD h3cVoPeerDefault1stCodecLevel	1.3.6.1.4.1.2011.10.2.39.5.1.4.2	CodecType	read-write	The default priority of the first level CODEC(coding and decoding).
COD h3cVoPeerDefault2ndCodecLevel	1.3.6.1.4.1.2011.10.2.39.5.1.4.3	CodecType	read-write	The default priority of the second level CODEC(coding and decoding).
COD h3cVoPeerDefault3rdCodecLevel	1.3.6.1.4.1.2011.10.2.39.5.1.4.4	CodecType	read-write	The default priority of the third level CODEC(coding and decoding).
COD h3cVoPeerDefault4thCodecLevel	1.3.6.1.4.1.2011.10.2.39.5.1.4.5	CodecType	read-write	The default priority of the fourth level CODEC(coding and decoding).
INT h3cVoPeerDefaultVADOn	1.3.6.1.4.1.2011.10.2.39.5.1.4.6	INTEGER	read-write	The default value of dial peer's VAD(Voice Activity Detection).
I32 h3cVoPeerDefaultFaxTransLevel	1.3.6.1.4.1.2011.10.2.39.5.1.4.7	Integer32	read-write	The default value of dial peer's fax transmit level. The unit is db.
I32 h3cVoPeerDefaultFaxLocalTrain	1.3.6.1.4.1.2011.10.2.39.5.1.4.8	Integer32	read-write	The default value of dial peer's fax local train threshold.
FAX h3cVoPeerDefaultFaxProtocol	1.3.6.1.4.1.2011.10.2.39.5.1.4.9	FaxProtocolType	read-write	The default value of dial peer's fax protocol.
I32 h3cVoPeerDefaultFaxHSRedunNum	1.3.6.1.4.1.2011.10.2.39.5.1.4.10	Integer32	read-write	The default value of dial peer's T38 fax protocol high redundancy packet number.
I32 h3cVoPeerDefaultFaxLSRedunNum	1.3.6.1.4.1.2011.10.2.39.5.1.4.11	Integer32	read-write	The default value of dial peer's T38 fax protocol low redundancy packet number.
FAX h3cVoPeerDefaultFaxBaudrate	1.3.6.1.4.1.2011.10.2.39.5.1.4.12	FaxBaudrateType	read-write	The default value of dial peer's fax baudrate.
INT h3cVoPeerDefaultFaxNSF	1.3.6.1.4.1.2011.10.2.39.5.1.4.13	INTEGER	read-write	The default value of fax NSF(non-standard faculty).
FAX h3cVoPeerDefaultFaxSupportMode	1.3.6.1.4.1.2011.10.2.39.5.1.4.14	FaxSupportModeType	read-write	The default mode of fax supported.
FAX h3cVoPeerDefaultFaxTrainMode	1.3.6.1.4.1.2011.10.2.39.5.1.4.15	FaxTrainMode	read-write	The default value of fax training mode.
INT h3cVoPeerDefaultFaxECM	1.3.6.1.4.1.2011.10.2.39.5.1.4.16	INTEGER	read-write	The default value of fax ECM(Error Correct Mode) Mode.
h3cVoPeerCfgCallerPermitTable	1.3.6.1.4.1.2011.10.2.39.5.1.5		not-accessible	The table contains permitted caller number in the specific voice entity for incoming call.
h3cVoPeerCfgCallerPermitEntry	1.3.6.1.4.1.2011.10.2.39.5.1.5.1		not-accessible	The entry of h3cVoPeerCfgCallerPermitTable.
OCT h3cVoPeerCfgCallerPermitNum	1.3.6.1.4.1.2011.10.2.39.5.1.5.1.1	OCTET STRING	not-accessible	This object specifies permitted caller number.
ROW h3cVoPeerCallerPermitRowStatus	1.3.6.1.4.1.2011.10.2.39.5.1.5.1.2	RowStatus	read-create	This object is used to create, delete or modify a row in this table.

RFC description

H3C MIB for voice dial control managing dial peers, call routing rules, and voice traffic engineering.

Start monitoring H3C VoIP gateway/router (voice dial control/dial-peer routing) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download H3C-VODIALCONTROL-MIB

What Is H3C-VODIALCONTROL-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description