G700-MG-MIB

All MIBs › G700-MG-MIB

Organization: Avaya, Inc.

Last Updated: 2014-05-08

Category: Domain: Telephony/VoIP, Vendor: Avaya

Description: Avaya G700 Media Gateway MIB for managing VoIP media gateway modules, DSP resources, and call routing.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is G700-MG-MIB?

G700-MG-MIB (registered as cmgmib under Avaya's enterprise OID) is a vendor-specific MIB modeling Avaya's H.248-based media gateways, including the G700, G350, G450, and related Communication Manager Branch Edition platforms, spanning chassis hardware, installed media modules, and VoIP subsystem health. It exposes chassis inventory and environmental data (cmgHWType, cmgModuleTable with per-slot cmgModuleType/cmgModuleFaultMask/cmgModuleStatusMask), hardware sensor readings (cmgCpuTemp, cmgDspTemp, and multiple power-supply voltage objects with associated warning/shutdown thresholds), and a detailed cmgHardwareFaultMask bitmask covering fan, temperature, power-supply, and clock-synchronization faults. This lets an operator monitor the physical health of a media gateway chassis -- fan speed, internal temperatures, power rails, and installed module status -- which is critical because a gateway failure interrupts voice/VoIP service for an entire branch or PBX trunk group. It imports from LOAD-MIB for firmware version tracking on each module and from INET-ADDRESS-MIB for IPv6-capable configuration objects added in later revisions. It is deployed on Avaya G700/G450/G350 media gateways in enterprise telephony deployments, and engineers evaluating this module in a G700-MG-MIB MIB Browser can inspect every fault bit and sensor threshold before deploying to production.

IPNetwork Monitor allows you to monitor SNMP objects defined in G700-MG-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Avaya G700/G450/G350 H.248 Media Gateways

Monitoring Examples

An operator polls cmgHardwareFaultMask and cmgModuleFaultMask for each slot in cmgModuleTable, alongside cmgCpuTemp and cmgCpuTempWarningThresh; a fault mask bit indicating a power-supply or fan failure combined with a CPU temperature approaching its warning threshold would flag an at-risk media gateway chassis in need of preventive maintenance.

What Can Be Monitored

chassis hardware type and installed module inventory
per-module fault and status bitmasks
CPU and DSP temperature sensors
power-supply voltage readings against warning/shutdown thresholds
hardware fault mask (fan, temperature, power, clock sync)
VoIP DSP core/engine fault indicators

Imported Objects

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From LOAD-MIB

genAppFileId	OBJECT-TYPE
genAppFileName	OBJECT-TYPE
genAppFileVersionNumber	OBJECT-TYPE
genOpLastFailureIndex	OBJECT-TYPE
genOpLastWarningDisplay	OBJECT-TYPE

From RFC1155-SMI

TimeTicks

From RFC1213-MIB

DisplayString

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
enterprises

From SNMPv2-TC

RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
avaya	1.3.6.1.4.1.6889
products	1.3.6.1.4.1.6889.1
g700MediaGateway	1.3.6.1.4.1.6889.1.9
mibs	1.3.6.1.4.1.6889.2
g700MediaGatewayMIB	1.3.6.1.4.1.6889.2.9
cmgmib	1.3.6.1.4.1.6889.2.9.1			A MIB to support the Avaya H248 Media Gateways.
cmgChassis	1.3.6.1.4.1.6889.2.9.1.1
INT cmgHWType	1.3.6.1.4.1.6889.2.9.1.1.1	INTEGER	read-only	Indicates the type of component. Where 'media-gateway' refers to G700
STR cmgModelNumber	1.3.6.1.4.1.6889.2.9.1.1.2	DisplayString	read-only	Model number of this component.
STR cmgDescription	1.3.6.1.4.1.6889.2.9.1.1.3	DisplayString	read-only	Description of this component: G700 Media Gateway.
STR cmgSerialNumber	1.3.6.1.4.1.6889.2.9.1.1.4	DisplayString	read-only	Serial number of this gateway.
STR cmgHWVintage	1.3.6.1.4.1.6889.2.9.1.1.5	DisplayString	read-only	Hardware version of this gateway.
STR cmgHWSuffix	1.3.6.1.4.1.6889.2.9.1.1.6	DisplayString	read-only	Hardware vintage suffix of this gateway.
INT cmgStackPosition	1.3.6.1.4.1.6889.2.9.1.1.7	INTEGER	read-only	Position of this media gateway in the Cajun stack, counting from the bottom of the stack.
OCT cmgModuleList	1.3.6.1.4.1.6889.2.9.1.1.8	OCTET STRING	read-only	List of the physical media modules installed in this gateway. Meaning of each octet is as follows. 1 Number of slots; in the G700 Media Gateway this is always 4. 2 Type of slot identifier; in the G700 Media Gateway this is always integer(2). 3-4 Length of each field in the following sequence; in the G700 Media Gateway this is always 1. 5-14 Module type ids in slot order, 1 - 10. Values are defined below for cmgModuleType, or none(0) if no module is installed. none(0), -- no module installed t1e1-voip(1), -- T1/E1 with integrated CSU/DSU & VoIP DSP bri(2), -- BRI trunk module dcp(3), -- DCP station module analog(4), -- combination analog line and trunk t1e1(5), -- T1/E1 with integrated CSU/DSU voip(6), -- dedicated VoIP media module icc(7), -- internal call controller fxo4fxs4(9), -- MM714 4 FXS + 4FXO analog ports module bri2(10), -- MM722 2 BRI trunk ports module ds1wan(11), -- MM340 1 DS1 (E1/T1) WAN data port module uspwan(12), -- MM342 1 USP WAN data port module dcp24hd(13), -- HDMM312 24 DCP station ports G350 high-density form-factor module poe24(14), -- HDMM314 24 power over Ethernet plus 1 GBIC port g350intana(16), -- G350 Integrated analog module dcp24(17), -- MM717 24 DCP station ports module fxs24(18), -- MM716 24 FXS analog ports module g250-int-analog-2L4T(19), -- G250 Integrated analog 2 Lines + 4 Trunks module g250-int-analog-2L1T(20), -- G250 Integrated analog 2 Lines + 1 Trunk module g250-int-BRI(21), -- G250 Integrated BRI Trunk module g250-int-DS1(24), -- G250 Integrated DS1 Trunk module g250-int-12pDCP(23), -- G250 Integrated 12 Port DCP lines module poe40(22), -- HDMM316 40 power over Ethernet plus 1 Giga bit copper poe24cr(25), -- HDMM314 24 power over Ethernet plus 1 GBIC port (Cost Reduction) poe8(26), -- MM118 - 8 10/100 power over Ethernet ports module tgm550-int-analog-2L2T(30), -- TGM550 Integrated analog 2 Lines + 2 Trunks module tim514(31), -- TIM514 4 FXS + 4 FXO analog ports module tim510(32), -- TIM510 1 DS1 (E1/T1) module tim521(33), -- TIM521 4 BRI trunk ports module avayaAM110ApplicationModule(34), -- Avaya Communication Manager Branch Edition Application Module for i40 and i120. g450Mainboard(40), -- G450 mainboard tim508(41), -- TIM508 8 FXS analog ports module tim516(42), -- TIM516 16 FXS analog ports module tim518(43), -- TIM518 8 FXS + 8 FXO analog ports module i120-intana(44), -- i120 Integrated analog module i40-int-analog-2L4T(45), -- avayaCommunicationManagerBranchEditioni40 Integrated analog 2 Lines + 4 Trunks module i40-int-analog-2L1T(46), -- avayaCommunicationManagerBranchEditioni40 Integrated analog 2 Lines + 1 Trunk module i40-int-BRI(47), -- avayaCommunicationManagerBranchEditioni40 Integrated BRI Trunk module i40-int-DS1(48), -- avayaCommunicationManagerBranchEditioni40 Integrated DS1 Trunk module i40-A14-int-analog-6L8T(49), -- avayaCommunicationManagerBranchEditioni40 Integrated analog 6 Lines + 8 Trunks module avayaCommunicationManagerBranchEditionG450Mainboard(50), -- Mainboard g430Mainboard(51), bri8(52), -- MM721 8 BRI trunk ports module unknown(255) -- type cannot be determined
INT cmgReset	1.3.6.1.4.1.6889.2.9.1.1.9	INTEGER	read-write	Setting the value of this attribute to ON is interpreted as a reset command for the whole chassis. It initiates a complete reinitialisation of the chassis and of all the devices incorporated inside the chassis.
cmgHardware	1.3.6.1.4.1.6889.2.9.1.1.10
I32 cmgCpuTemp	1.3.6.1.4.1.6889.2.9.1.1.10.1	Integer32	read-only	Reading of the internal temperature sensor at the CPU, expressed in degrees Celsius.
I32 cmgCpuTempWarningThresh	1.3.6.1.4.1.6889.2.9.1.1.10.2	Integer32	read-only	Internal enclosure temperature warning threshold, expressed in degrees Celsius. When the temperature at the CPU sensor exceeds the threshold, a trap is sent to the management console. If both CPU and DSP sensors exceed their thresholds, only one trap is sent.
I32 cmgCpuTempShutdownThresh	1.3.6.1.4.1.6889.2.9.1.1.10.3	Integer32	read-only	Internal enclosure temperature shutdown threshold, expressed in degrees Celsius. When the temperature at the CPU sensor exceeds the threshold, a trap is sent to the management console and the media gateway begins a controlled shutdown.
I32 cmgDspTemp	1.3.6.1.4.1.6889.2.9.1.1.10.4	Integer32	read-only	Reading of the internal temperature sensor at the DSPs, expressed in degrees Celsius.
I32 cmgDspTempWarningThresh	1.3.6.1.4.1.6889.2.9.1.1.10.5	Integer32	read-only	Internal enclosure temperature warning threshold, expressed in degrees Celsius. When the temperature at the DSP sensor exceeds the threshold, a trap is sent to the management console. If both CPU and DSP sensors exceed their thresholds, only one trap is sent.
I32 cmgDspTempShutdownThresh	1.3.6.1.4.1.6889.2.9.1.1.10.6	Integer32	read-only	Internal enclosure temperature shutdown threshold, expressed in degrees Celsius. When the temperature at the DSP sensor exceeds the threshold, a trap is sent to the management console and the media gateway begins a controlled shutdown.
I32 cmgPowerMgProcessor	1.3.6.1.4.1.6889.2.9.1.1.10.7	Integer32	read-only	Voltage reading in millivolts at the power supply serving the Media Gateway main processor. Nominal value is +5100 mV. If the reading falls outside the range 4950 to 5250 mV, a trap is sent to the management console and the corresponding bit in the fault mask is turned on.
I32 cmgPowerMediaModules	1.3.6.1.4.1.6889.2.9.1.1.10.8	Integer32	read-only	Voltage reading in millivolts at the power supply serving the Media Modules. Nominal value is -48000 mV. If the reading falls outside the range -43000 to -53000 mV, a trap is sent to the management console and the corresponding bit in the fault mask is turned on.
I32 cmgPowerVoipComplex	1.3.6.1.4.1.6889.2.9.1.1.10.9	Integer32	read-only	Voltage reading in millivolts at the power supply serving the VoIP complexes. Nominal value is +3400 mV. If the reading falls outside the range 3200 to 3600 mV, a trap is sent to the management console and the corresponding bit in the fault mask is turned on.
I32 cmgPowerDsp	1.3.6.1.4.1.6889.2.9.1.1.10.10	Integer32	read-only	Voltage reading in millivolts at the power supply serving the DSP units, derived from VoIP complex power. Nominal value is +1580 mV. If the reading falls outside the range 1530 to 1620 mV, a trap is sent to the management console and the corresponding bit in the fault mask is turned on.
I32 cmgPower8260	1.3.6.1.4.1.6889.2.9.1.1.10.11	Integer32	read-only	Voltage reading in millivolts at the power supply serving the 8260 processor, derived from VoIP complex power. Nominal value is +2500 mV. If the reading falls outside the range 2430 to 2580 mV, a trap is sent to the management console and the corresponding bit in the fault mask is turned on.
OCT cmgHardwareFaultMask	1.3.6.1.4.1.6889.2.9.1.1.10.12	OCTET STRING	read-only	Each bit of this value set to '1' indicates a specific fault in the module. Octets are numbered in the order in which they appear in the PDU. Bits are numbered from the most-significant leftmost bit in the octet (bit 0) to the least-significant rightmost bit (bit 7). Cajun numbering continues across octets, so that octet 1 bit 0 is called bit 8 in the Cajun scheme. That number is also shown below, with the octet value for each single bit set. Octet 0 high-order 4 bits show fan status. Octet 0 low-order 4 bits show temperature status. Octet 1 shows power supply status. Octet 2 shows other alarms. Cajun Octet Octet bit# /bit# value Meaning ----- ----- ----- ------- 0 0/0 0x80 Multiple fan warning: at least two fans have been operating at less than 90% of their nominal speed for 5 minutes or more. This may be an early warning of overheating. 1 0/1 0x40 PSU fan brief failure warning: the power supply fan has been operating at less than 90% of its nominal speed for 10 minutes or more, but less than 15 minutes. This may be an early warning of overheating. 2 0/2 0x20 PSU fan prolonged failure warning: the power supply fan has been operating at less than 90% of its nominal speed for 15 minutes or more. This may be an early warning of overheating. 3 0/3 Unused. 4 0/4 0x08 Temperature warning: cmgCpuTemp has exceeded its warning threshold. 5 0/5 0x04 Temperature warning: cmgDspTemp has exceeded its warning threshold. 6 0/6 Unused. 7 0/7 Power On Status Test failure -NCE, QUICC test failures on power up 8 1/0 0x80 The +5.1 v power supply to the MG processor is out of range. 9 1/1 0x40 The -48 v power supply to the media modules is out of range. 10 1/2 0x20 The +3.3 v power supply to the VoIP complexes is out of range. 11 1/3 0x10 The +1.58 v power supply to the DSP units is out of range. 12 1/4 0x08 The +2.5 v power supply to the 8260 processor is out of range. 13 1/5 0x04 The -48 v auxiliary power supply to the endpoints is out of range. 14 1/6 0x02 The +12 v power supply to the fans is out of range. 15 1/7 Unused. 16 2/0 0x80 Clock synchronization signal is lost. 17 2/1 0x40 Clock synchronization signal warning. Only one clock syncronization signal source remains. 18 2/2 0x20 Clock synchronization signal excessive switching. 19 2/3 0x10 TDM Test Expansion Box 1 Failure 20 2/4 0x08 TDM Test Expansion Box 2 Failure 21 2/5 0x04 PoE Power Supply Base Box Failure 22 2/6 0x02 PoE Power Supply Expansion Box 1 Failure 23 2/7 0x01 PoE Power Supply Expansion Box 2 Failure
OCT cmgHardwareStatusMask	1.3.6.1.4.1.6889.2.9.1.1.10.13	OCTET STRING	read-only	Each bit of this value set to '1' indicates a specific status condition in the module. Octets are numbered in the order in which they appear in the PDU. Bits are numbered from the most-significant leftmost bit in the octet (bit 0) to the least-significant rightmost bit (bit 7). Cajun numbering continues across octets, so that octet 1 bit 0 is called bit 8 in the Cajun scheme. That number is also shown below, with the octet value for each single bit set. Octet 0 high-order 4 bits show LED status. Octet 0 low-order 4 bits show ICC status. Octets 1 - 5 show power-on self test (POST) results. Cajun Octet Octet bit# bit# value Meaning ----- ----- ----- ------- 0 0/0 0x80 Media gateway red LED is on. 1 0/1 0x40 The red LED is on in one or more of the media modules. 2-3 0/2-3 Unused. 4 0/4 0x08 Integrated Communications Controller hardware watchdog alert is on. 5-7 0/5-7 Unused. 8 1/0 0x80 POST HDLC local loopback failed. 9 1/1 0x40 POST Ethernet local loopback failed. 10 1/2 0x20 POST Ethernet physical local loopback failed. 11 1/3 0x10 POST Port I/O read-write test failed. 12-15 1/4-7 Unused. 16 2/0 0x80 POST NCE0 reset failed. 17 2/1 0x40 POST NCE0 internal RAM test failed. 18 2/2 0x20 POST NCE0 FIFO loop-around failed. 19 2/3 0x10 POST NCE0 internal channel loopback failed. 20 2/4 0x08 POST NCE0 internal TDM loopback failed. 21 2/5 0x04 POST NCE0 external channel loopback failed. 22-23 2/6-7 Unused. 24 3/0 0x80 POST NCE1 reset failed. 25 3/1 0x40 POST NCE1 internal RAM test failed. 26 3/2 0x20 POST NCE1 FIFO loop-around failed. 27 3/3 0x10 POST NCE1 internal channel loopback failed. 28 3/4 0x08 POST NCE1 internal TDM loopback failed. 29 3/5 0x04 POST NCE1 external channel loopback failed. 30-31 3/6-7 Unused. 32 4/0 0x80 POST DSP reset failed. 33 4/1 0x40 POST POST SPI internal loopback failed. 34 4/2 0x20 POST Spitfire FIFO test failed. 35 4/3 0x10 POST ADC test failed. 36 4/4 0x08 POST CPLD access test failed. 37-39 4/5-7 Unused. 40-47 5/0-7 Unused.
INT cmgHardwareFanLowSpeedLevel	1.3.6.1.4.1.6889.2.9.1.1.10.14	INTEGER	read-write	The fan speed level mode. Disable(2) is used for normal operation of two fan speeds. Enable(1) is used to activate additional lower speed level. Default is disable(2).
cmgModules	1.3.6.1.4.1.6889.2.9.1.1.11
cmgModuleTable	1.3.6.1.4.1.6889.2.9.1.1.11.1		not-accessible	Table of physical media modules in this media gateway.
cmgModuleEntry	1.3.6.1.4.1.6889.2.9.1.1.11.1.1		not-accessible	An entry in the table, representing a single media module.
INT cmgModuleSlot	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.1	INTEGER	read-only	Slot number of this module.
INT cmgModuleType	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.2	INTEGER	read-only	Type of this module.
STR cmgModuleDescription	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.3	DisplayString	read-only	Description of this media module, e.g. 'Avaya E1/T1 media module with integrated CSU/DSU'
STR cmgModuleName	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.4	DisplayString	read-only	User-assigned name of this media module.
STR cmgModuleSerialNumber	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.5	DisplayString	read-only	Serial number of this module. The first 12 characters are meaningful. Form is yyLLmmnnnnnn, where yy = last 2 digits of the year of manufacture LL = manufacturing facility, e.g. DR for Denver, Colorado mm = month of manufacture, 01 - 12 nnnnnn = a six-digit sequence number
STR cmgModuleHWVintage	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.6	DisplayString	read-only	Hardware vintage of this module.
STR cmgModuleHWSuffix	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.7	DisplayString	read-only	Hardware vintage suffix of this module.
STR cmgModuleFWVersion	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.8	DisplayString	read-only	Firmware version of this module. This duplicates information available in the Load MIB. It shows the media module run image version, plus the VoIP engine version if applicable.
INT cmgModuleNumberOfPorts	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.9	INTEGER	read-only	Number of physical connectors on this module.
OCT cmgModuleFaultMask	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.10	OCTET STRING	read-only	Each bit of this value set to '1' indicates a specific fault in the module. Octets are numbered in the order in which they appear in the PDU. Bits are numbered from the most-significant leftmost bit in the octet (bit 0) to the least-significant rightmost bit (bit 7). Cajun numbering continues across octets, so that octet 1 bit 0 is called bit 8 in the Cajun scheme. That number is also shown below, with the octet value for each single bit set. Cajun Octet Octet bit# bit# value Meaning ----- ----- ----- ------- 0 0/0 0x80 Media module is in administrative busy-out. 1 0/1 0x40 One or more ports on this media module is in administrative busy-out. 2 0/2 0x20 Insertion sequence failed. 3 0/3 AWOH data module conflict. 4 0/4 0x08 Media module automatic reset occurred. 5 0/5 0x04 One or more power-on startup tests failed. 6 0/6 0x02 Media module parameter exchange failed. 7 0/7 Unsupported module enrolment. 8-15 1/0-7 Unused.
OCT cmgModuleStatusMask	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.11	OCTET STRING	read-only	Each bit of this value set to '1' indicates a specific status condition in the module. Octets are numbered in the order in which they appear in the PDU. Bits are numbered from the most-significant leftmost bit in the octet (bit 0) to the least-significant rightmost bit (bit 7). Cajun numbering continues across octets, so that octet 1 bit 0 is called bit 8 in the Cajun scheme. That number is also shown below, with the octet value for each single bit set. Cajun Octet Octet bit# bit# value Meaning ----- ----- ----- ------- 0 0/0 0x80 Red LED is on. 1 0/1 0x40 Module controlled by ACP on communications controller. 2-7 0/2-7 Unused. 8-15 1/0-7 Unused.
INT cmgModuleReset	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.12	INTEGER	read-write	Setting the value of this attribute to ON is interpreted as a reset command for the module. It initiates a complete reinitialization of the module and of all the devices incorporated inside the module.
INT cmgModuleNumberOfChannels	1.3.6.1.4.1.6889.2.9.1.1.11.1.1.13	INTEGER	read-only	Number of communications channels or spans on this module. Earlier Avaya products have referred to T1E1 channels as ports. This media gateway calls them channels.
cmgDsu	1.3.6.1.4.1.6889.2.9.1.1.11.2
cmgDsuConfigTable	1.3.6.1.4.1.6889.2.9.1.1.11.2.1		not-accessible	Configuration of E1/T1 DSUs in this media gateway.
cmgDsuConfigEntry	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1		not-accessible	An entry in the table, representing the configuration of one DSU on a T1/E1 media module.
INT cmgDsuSlot	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.1	INTEGER	read-only	Slot number of this DSU.
INT cmgDsuPort	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.2	INTEGER	read-only	Port number of this DSU.
INT cmgDsuPortEnable	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.3	INTEGER	read-write	This object allows a user to take the E1/T1 port out of service for administration. During administration, it may be in an inconsistent state. When administration is complete, the port may be enabled again. If the port is not yet correctly administered, the change to the enabled state will fail with an INCONSISTENT_VALUE error.
INT cmgDsuDataFormat	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.4	INTEGER	read-write	Data format (channel rate) of this DSU.
INT cmgDsuFlowControl	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.5	INTEGER	read-write	Specifies the conditions under which this DSU will send all ones to indicate data port not ready. dtr-rts(1) Monitor both DTR and RTS as described below. If either is interrupted, send all ones. dtr(2) Monitor the DTE Ready interchange circuit CD (CCITT 108/1/2). If DTR is interrupted, send all ones. rts(3) Monitor the Request-to-Send interchange circuit CD (CCITT 105). If RTS is interrupted, send all ones. disable(4) Do not monitor interchange circuits from the DTE.
INT cmgDsuYellowAlarmAction	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.6	INTEGER	read-write	Specifies the action to take when a yellow alarm is received on the network interface. noAction(1) Ignore yellow alarms. halt(2) Stop transmission and disable the data port. Send all ones on the Received Data interchange circuit BB (CCITT 104) and interrupt the Clear-to-Send interchange circuit (CCITT 106).
INT cmgDsuReceiveClock	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.7	INTEGER	read-write	Specifies whether data received from the data port is clocked using the DSU internal clock or by an external clock provided by the DTE connected to the port. When an external clock is used, it must be synchronized to the same clock source as the DSU. The DSU Receive Clock is equivalent to the Data Port Transmit Clock. internal(1) The clock is provided internally by the DSU/CSU on the TXC interchange circuit DB (CCITT 114). external(2) The clock is provided externally by the DTE on the XTXC interchange circuit DA (CCITT 113).
INT cmgDsuInvertTxC	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.8	INTEGER	read-write	Specifies whether the clock supplied by the DSU/CSU on the TXC interchange circuit DB (CCITT 114) is phase inverted with respect to the Transmitted Data interchange ciucuit BA (CCITT 103). This option is useful when long cable lengths between the DSU/CSU and the DTE are causing data errors.
INT cmgDsuInvertRxC	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.9	INTEGER	read-write	Specifies whether the receive clock supplied by the DSU/CSU or DTE is phase inverted.
INT cmgDsuInvertTxD	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.10	INTEGER	read-write	Specifies whether the transmitted data stream is logically inverted before being transmitted. This option is useful for applications where HDLC data is being transported. Inverting the data ensures that the density requirements for the network interface are met.
INT cmgDsuInvertRxD	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.11	INTEGER	read-write	Specifies whether the received data stream is logically inverted. This option is useful for applications where HDLC data is being transported. Inverting the data ensures that the density requirements for the network interface are met.
INT cmgDsuPortInitiatedLoopback	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.12	INTEGER	read-write	Specifies whether the DSU should accept loopback requests from the DTE port. The local DTE can send an LL or RL signal to the T1/E1 media module in the EIA-530A interface. The LL signal causes the module to activate a local DTE loopback. An RL signal causes the module to send an in-band code to signal the far end to go into loopback.
INT cmgDsuNetworkInitiatedLoopback	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.13	INTEGER	read-write	Specifies whether the DSU should accept in-band loopback requests from the far end, that is, a DSU across the network.
OCT cmgDsuChannelAssignments	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.14	OCTET STRING	read-write	Specifies which channels are assigned to Voice and which to the DSU. Each bit represents one channel. If the bit is set to 1, the channel is assigned to the DSU; otherwise it is assigned to Voice. The channel number of a bit is determined by the formula (8n + b + 1), where n is the octet number and b is the bit number. So the 3rd bit in octet 2 represents channel (82 + 3 + 1) = 20.
INT cmgDsuDataRate	1.3.6.1.4.1.6889.2.9.1.1.11.2.1.1.15	INTEGER	read-only	Data format (channel rate) of this DSU times the number of channels of type ds0-dsu-channel(5). See cmgChType in cmgChannelTable.
cmgDsuPortStatusTable	1.3.6.1.4.1.6889.2.9.1.1.11.2.2		not-accessible	Status of E1/T1 DSUs in this media gateway.
cmgDsuPortStatusEntry	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1		not-accessible	An entry in the table, representing the configuration of one DSU on a T1/E1 media module.
INT cmgDsuRTS	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.1	INTEGER	read-only	State of request-to-send signal from the DTE to the DSU.
INT cmgDsuDTR	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.2	INTEGER	read-only	State of data-terminal-ready signal from the DTE to the DSU.
INT cmgDsuLL	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.3	INTEGER	read-only	Is there a DTE local loopback active between the DTE and the DSU?
INT cmgDsuRL	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.4	INTEGER	read-only	Is there a remote loopback active in the FPGA?
INT cmgDsuRLSD	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.5	INTEGER	read-only	State of the Receive Line Signal Detect from the DSU to the DTE.
INT cmgDsuCTS	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.6	INTEGER	read-only	State of clear-to-send signal from the DSU to the DTE.
INT cmgDsuDSR	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.7	INTEGER	read-only	State of data-set-ready signal from the DCE to the DTE.
INT cmgDsuRing	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.8	INTEGER	read-only	State of the DCE ring indicator signal to the DTE.
INT cmgDsuTestMode	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.9	INTEGER	read-only	Indicates whether tests are currently in progress.
INT cmgDsuTxD	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.10	INTEGER	read-only	State of data transmission from the synchronous DTE to the data port on the DSU.
INT cmgDsuRxD	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.11	INTEGER	read-only	State of data reception at the synchronous DTE from the data port on the DSU/CSU.
OCT cmgDsuFaultMask	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.12	OCTET STRING	read-only	Each bit of this value set to '1' indicates a specific fault in this DSU. Octets are numbered in the order in which they appear in the PDU. Bits are numbered from the most-significant leftmost bit in the octet (bit 0) to the least-significant rightmost bit (bit 7). Cajun numbering continues across octets, so that octet 1 bit 0 is called bit 8 in the Cajun scheme. That number is also shown below, with the octet value for each single bit set. Cajun Octet Octet bit# bit# value Meaning ----- ----- ----- ------- 0 0/0 0x80 DSU FPGA configuration failure. 1 0/1 0x40 DSU automatic reset. 2-3 0/2-3 Unused. 4 0/4 0x08 DSU DTE DTR off - DTE is disconnected or not functioning. 5 0/5 0x04 DSU DTE RTS off - DTE is not sending data. 6 0/6 0x02 DSU TxD failure - data received from DTE is all zeroes or all ones. 7 0/7 0x01 DSU RxD failure - data received from far end is all zeroes or all ones. 8-15 1/0-7 Unused.
OCT cmgDsuStatusMask	1.3.6.1.4.1.6889.2.9.1.1.11.2.2.1.13	OCTET STRING	read-only	Each bit of this value set to '1' indicates a specific status condition in this DSU, or a fault or status condition in its associated CSU. Octets are numbered in the order in which they appear in the PDU. Bits are numbered from the most-significant leftmost bit in the octet (bit 0) to the least-significant rightmost bit (bit 7). Cajun numbering continues across octets, so that octet 1 bit 0 is called bit 8 in the Cajun scheme. That number is also shown below, with the octet value for each single bit set. If the CSU is reporting a Blue Alarm (AIS), multiple other alarms may be hidden by the Blue Alarm. -- The four octets of the T1E1 status mask are taken from three different -- maintenance APIs and assembled by the SNMP agent. Octets 0-1 show CSU fault status. -- From t1e1csu_status.mask, built by the macro T1E1CSU_STATUS_MKMASK. -- This is defined in CAPIStructures.h:851 and used in T1E1Csu.C:194. Octet 2 shows CSU loopbacks active. -- From t1e1csu_lpbkstatus.mask, built by the macro T1E1CSU_LPBKSTATUS_MKMASK. -- This is defined in CAPIStructures.h:803 and used in T1E1Csu.C:173. Octet 3 shows DSU loopbacks active. -- From t1e1dsu_tstmgmt.mask, built by the macro T1E1DSU_TSTMGMT_MKMASK -- This is defined in CAPIStructures.h:1115 and used in T1E1Dsu.C:1574. -- Note this just copies t1e1dsu_tstmgmt.status_lpbk into the mask field. -- Don't confuse t1e1dsu_tstmgmt.lpbk and t1e1dsu_tstmgmt.status_lpbk. The -- first is what a CLI user requested; the second is what the board reports. -- -- The bit assignments are chosen to facilitate retrieval from the board. Cajun Octet Octet bit# bit# value Meaning ----- ----- ----- ------- 0-5 0/0-5 Unused. 6 0/6 0x02 CSU CRC multiframe lost (LCM) - E1 only 7 0/7 0x01 CSU remote multiframe alignment lost (RMA) - E1 only 8 1/0 0x80 CSU local multiframe alignment lost (LMA) - E1 only 9 1/1 0x40 CSU polar density violations (PDV) - in the T1 configuration using AMI line coding, this is equivalent to bipolar violations (BPV). 10 1/2 0x20 CSU alarm indication signal (AIS, Blue Alarm). 11 1/3 0x10 CSU remote alarm indication signal (RAI, Yellow Alarm). 12 1/4 0x08 CSU loss of frame (LOF, Red Alarm) - unable to synchronize 13 1/5 0x04 CSU excessive error rate (EER) - applies to ESF framing only. on DS1 signal. 14 1/6 0x02 CSU out of frame (OOF) - 2 of 4 frame synchronization bits in error. 15 1/7 0x01 CSU loss of signal (LOS) - 175 consecutive zeroes received. 16-20 2/0-4 Unused. 21 2/5 0x04 CSU Digital diagnostic loopback active (towards DTE). This is the equivalent of either equipment (DTE) or repeater loopback in the Paradyne 3160. 22 2/6 0x02 CSU Line loopback active (towards network). 23 2/7 0x01 CSU Payload loopback active (towards network). 24-26 3/0-2 Unused. 27 3/3 0x10 DSU Far-end Data Channel loopback active. 28 3/4 0x08 DSU Data Terminal loopback active. 29 3/5 0x04 DSU Remote loopback active. 30 3/6 0x02 DSU Near-end Data Channel loopback active. 31 3/7 0x01 DSU Local DTE loopback active.
cmgDsuTestTable	1.3.6.1.4.1.6889.2.9.1.1.11.2.3		not-accessible	Loopback tests in effect on DSUs in this media gateway.
cmgDsuTestEntry	1.3.6.1.4.1.6889.2.9.1.1.11.2.3.1		not-accessible	An entry in the table, representing the configuration of one DSU on a T1/E1 media module.
INT cmgDsuLoopbackPattern	1.3.6.1.4.1.6889.2.9.1.1.11.2.3.1.1	INTEGER	read-only	Specifies the pattern to be sent during a loopback test. allZeroes(1) is most often used to verify B8ZS line encoding. allOnes(2) is most often used to measure signal power. oneZeroOne(3) alternates ones and zeroes. It is most often used to test bridge taps. oneIn5(4) is the pattern '00001', to send a remote loopback request. oneIn8(5) is the pattern '00000001', used to test repeater timing recovery. threeIn24(6) is 21 zeroes followed by 3 ones, used to test the ones density tolerance in AMI coded lines. qrs(7) is a quasi-random signal approximating live data. It is also available in repeating patterns of 511 or 2047 bits. none means no pattern; used for response.
INT cmgDsuLocalDteLoopback	1.3.6.1.4.1.6889.2.9.1.1.11.2.3.1.2	INTEGER	read-only	Indicates whether a Local DTE loopback is active, in which a signal received from the DTE is looped back after passing through the transceivers, but before passing through the FIFOs. This loopback can be activated by this DSU or by the local DTE.
INT cmgDsuNearEndDataChannelLoopback	1.3.6.1.4.1.6889.2.9.1.1.11.2.3.1.3	INTEGER	read-only	Indicates whether a Near-end Data Channel loopback is active, in which a signal received from the CSU is looped back after passing through the FIFOs but before entering the transceivers. This loopback was activated by the near end, that is, this DSU.
INT cmgDsuFarEndDataChannelLoopback	1.3.6.1.4.1.6889.2.9.1.1.11.2.3.1.4	INTEGER	read-only	Indicates whether a Far-end Data Channel loopback is active. This is functionally equivalent to the Near-end Data Channel loopback, except that this loopback was activated by the far end, that is, a DSU across the network.
INT cmgDsuRemoteLoopback	1.3.6.1.4.1.6889.2.9.1.1.11.2.3.1.5	INTEGER	read-only	Indicates whether a Remote loopback is active, in which a signal received from the CSU is looped back before entering the FIFOs. This loopback may have been activated by either the near end (this DSU) or the far end (a DSU across the network).
INT cmgDsuDataTerminalLoopback	1.3.6.1.4.1.6889.2.9.1.1.11.2.3.1.6	INTEGER	read-only	Indicates whether a Data Terminal loopback is active, in which a signal received from the DTE is looped back after passing through the FIFOs. This loopback can only be activated by the near end, that is, this DSU.
INT cmgDsuReset	1.3.6.1.4.1.6889.2.9.1.1.11.2.3.1.7	INTEGER	read-write	Set to on(1) to request reinitialization of the DSU.
cmgAnalogPorts	1.3.6.1.4.1.6889.2.9.1.1.12
cmgAnalogPortTable	1.3.6.1.4.1.6889.2.9.1.1.12.1		not-accessible	Table of analog ports in this media gateway.
cmgAnalogPortEntry	1.3.6.1.4.1.6889.2.9.1.1.12.1.1		not-accessible	An entry in the table, representing a single analog port.
INT cmgAnalogSlot	1.3.6.1.4.1.6889.2.9.1.1.12.1.1.1	INTEGER	read-only	Slot number of this analog port.
INT cmgAnalogPort	1.3.6.1.4.1.6889.2.9.1.1.12.1.1.2	INTEGER	read-only	Port number of this analog port.
INT cmgAnalogEchoCancellerControl	1.3.6.1.4.1.6889.2.9.1.1.12.1.1.3	INTEGER	read-write	The echo canceller control setting for this analog port. auto means that the system will enable or disable the echo canceller as appropriate for each call. fixedOn indicates that the analog firmware always enables the echo canceller (this value cannot be changed). Similarly, notSupported indicates that the analog HW does not contain echo cancellers (this value cannot be changed).
INT cmgAnalogEchoCancellerConfig1	1.3.6.1.4.1.6889.2.9.1.1.12.1.1.4	INTEGER	read-write	Echo canceller configuration setting for this analog port (byte 1 of 2). This value is not writeable if cmgAnalogEchoCancellerControl is fixedOn(3) or notSupported(4).
INT cmgAnalogEchoCancellerConfig2	1.3.6.1.4.1.6889.2.9.1.1.12.1.1.5	INTEGER	read-write	Echo canceller configuration setting for this analog port (byte 2 of 2). This value is not writeable if cmgAnalogEchoCancellerControl is fixedOn(3) or notSupported(4).
INT cmgAnalogBalance	1.3.6.1.4.1.6889.2.9.1.1.12.1.1.6	INTEGER	read-write	Balance index.
INT cmgAnalogReceiveGain	1.3.6.1.4.1.6889.2.9.1.1.12.1.1.7	INTEGER	read-write	The receive gain multiplied by 100, for instance -123 indicates -1.23dB.
INT cmgAnalogTransmitGain	1.3.6.1.4.1.6889.2.9.1.1.12.1.1.8	INTEGER	read-write	The transmit gain multiplied by 100, for instance +287 indicates 2.87dB.
cmgExpansionUnits	1.3.6.1.4.1.6889.2.9.1.1.13
cmgExpansionUnitsTable	1.3.6.1.4.1.6889.2.9.1.1.13.1		not-accessible	Table of Expansion Units connected to this media gateway.
cmgExpansions	1.3.6.1.4.1.6889.2.9.1.1.13.1.1		not-accessible	An entry in the table, representing a single Expansion Unit.
INT cmgExpansionSlot	1.3.6.1.4.1.6889.2.9.1.1.13.1.1.1	INTEGER	read-only	Expansion Unit Slot.
STR cmgExpansionModelNumber	1.3.6.1.4.1.6889.2.9.1.1.13.1.1.2	DisplayString	read-only	Expansion Unit model.
STR cmgExpansionDescription	1.3.6.1.4.1.6889.2.9.1.1.13.1.1.3	DisplayString	read-only	Expansion Unit description.
STR cmgExpansionSerialNumber	1.3.6.1.4.1.6889.2.9.1.1.13.1.1.4	DisplayString	read-only	Expansion Unit serial number.
STR cmgExpansionHWVintage	1.3.6.1.4.1.6889.2.9.1.1.13.1.1.5	DisplayString	read-only	Expansion Unit HW vintage.
STR cmgExpansionHWSuffix	1.3.6.1.4.1.6889.2.9.1.1.13.1.1.6	DisplayString	read-only	Expansion Unit HW suffix.
INT cmgExpansionDemandTest	1.3.6.1.4.1.6889.2.9.1.1.13.1.1.7	INTEGER	read-write	When set to on(1), activates on demand test for the Expansion Unit.
INT cmgExpansionDemandTestResult	1.3.6.1.4.1.6889.2.9.1.1.13.1.1.8	INTEGER	read-only	Result of the on demand test for the Expansion Unit. Failure(1) may be the result of a disconnected or bad cable.
INT cmgTimeslotMonitoring	1.3.6.1.4.1.6889.2.9.1.1.14	INTEGER	read-write	Timeslot Monitoring flag. When on, timeslot usage is monitored and traps are sent when thresholds are crossed. Those traps are cmgTimeslotOccupancyFault, cmgTimeslotOccupancyClear, cmgTimeslotAvailabilityFault and cmgTimeslotAvailabilityClear.
INT cmgTimeslotUpperThreshold	1.3.6.1.4.1.6889.2.9.1.1.15	INTEGER	read-write	Timeslot Upper threshold. The gateway will send trap cmgTimeslotOccupancyFault as soon as the timeslot usage goes above this threshold. This threshold must be set greater than the lower threshold; for example, cmgTimeslotLowerThreshold=85, cmgTimeslotUpperThreshold=90. Default is 90. cmgTimeslotMonitoring must be set to on(1) for traps to be sent.
INT cmgTimeslotLowerThreshold	1.3.6.1.4.1.6889.2.9.1.1.16	INTEGER	read-write	Timeslot Lower threshold. After the gateway has sent a cmgTimeslotOccupancyFault trap, it will send a cmgTimeslotOccupancyClear as soon as the timeslot usage goes below this threshold. Also after the gateway has sent a cmgTimeslotAvailabilityFault trap, it will send cmgTimeslotAvailabilityClear as soon as the timeslot usage goes below this threshold. This lower threshold must be less than the upper threshold; for example cmgTimeslotLowerThreshold=85, cmgTimeslotUpperThreshold=90. Default is 85. cmgTimeslotMonitoring must be set to on(1) for traps to be sent.
cmgProcessor	1.3.6.1.4.1.6889.2.9.1.2
cmgProcessorConfig	1.3.6.1.4.1.6889.2.9.1.2.1
STR cmgGatewayNumber	1.3.6.1.4.1.6889.2.9.1.2.1.1	DisplayString	read-only	Media gateway number by which the Call Controller knows this media module.
OCT cmgMACAddress	1.3.6.1.4.1.6889.2.9.1.2.1.2	OCTET STRING	read-only	MAC address of this processor.
OCT cmgFWVersion	1.3.6.1.4.1.6889.2.9.1.2.1.3	OCTET STRING	read-only	Firmware version of this gateway.
IP cmgCurrentIpAddress	1.3.6.1.4.1.6889.2.9.1.2.1.4	IpAddress	read-only	Current IP address of this processor. If cmgUseDhcpForIpAddress was on(1) at the time of last startup, this was received from the DHCP server. Otherwise it is the value of cmgStaticIpAddress at the last startup. If cmgUseDhcpForIpAddress was on(1) and the DHCP request failed, this value will be '0.0.0.0'.
INT cmgUseDhcpForIpAddress	1.3.6.1.4.1.6889.2.9.1.2.1.7	INTEGER	read-write	Specifies whether the gateway should get its IP address, default gateway, and subnet mask from the DHCP server, or use the locally administered static IP address, default gateway, and subnet mask.
INT cmgUseDhcpForVlan	1.3.6.1.4.1.6889.2.9.1.2.1.8	INTEGER	read-write	Specifies whether the gateway should get its VLAN ID from the DHCP server, or use the locally administered static VLAN ID cmgStatic802Vlan.
INT cmgDhcpSson	1.3.6.1.4.1.6889.2.9.1.2.1.9	INTEGER	read-write	Specifies the DHCP Site-Specific Option Number to use with a DHCP request. This gives the DHCP server information about the client's capabilities and properties.
IP cmgStaticIpAddress	1.3.6.1.4.1.6889.2.9.1.2.1.10	IpAddress	read-write	Locally administered static IP address of this processor. If cmgUseDhcpForIpAddress is on(1), this object is ignored.
STR cmgDnsServerList	1.3.6.1.4.1.6889.2.9.1.2.1.13	DisplayString	read-write	Comma-separated list of DNS server IP addresses this processor may use.
STR cmgDnsHostname	1.3.6.1.4.1.6889.2.9.1.2.1.14	DisplayString	read-only	DNS Hostname of this processor.
OCT cmgMgpFaultMask	1.3.6.1.4.1.6889.2.9.1.2.1.15	OCTET STRING	read-only	Each bit of this value set to '1' indicates a specific fault in the Media Gateway processor. Octets are numbered in the order in which they appear in the PDU. Bits are numbered from the most-significant leftmost bit in the octet (bit 0) to the least-significant rightmost bit (bit 7). Cajun numbering continues across octets, so that octet 1 bit 0 is called bit 8 in the Cajun scheme. That number is also shown below, with the octet value for each single bit set. Cajun Octet Octet bit# bit# value Meaning ----- ----- ----- ------- 0 0/0 0x80 Memory failure. 1 0/1 0x40 DHCP request failure. 2 0/2 0x20 Firmware download failure. 3 0/3 0x10 Software watchdog alert - MG processes restarting. 4 0/4 0x08 Internal Communications Controller expected but not present. 5 0/5 0x04 Internal Communications Controller automatic reset. 6 0/6 0x02 Media Gateway busy-out. 7 0/7 0x01 Configuration upload failure. 8 1/0 0x80 Primary controller not found. 9 1/1 0x40 No controller found. 10 1/2 0x20 Registration failure. 11 1/3 0x10 H.248 control link down. 12-13 1/4-5 Unused. 14 1/6 0x02 Maintenance test failure. 15 1/7 0x01 Maintenance test failure over threshold. 16 2/0 0x80 Configuration download failure. 17-23 2/0-7 Unused.
IPt cmgCurrentInetAddressType	1.3.6.1.4.1.6889.2.9.1.2.1.16	InetAddressType	read-only	Current IPv6 address type of this processor. The processor can have two IP address one IPv4 and the second IPv6. cmgCurrentIpAddress presents the IPv4 address and this MIB item presents the IPv6 address.
IP cmgCurrentInetAddress	1.3.6.1.4.1.6889.2.9.1.2.1.17	InetAddress	read-only	The Inet Address of the processor. 1. The address type of this object is specified in cmgCurrentInetAddressType. 2. Default of cmgCurrentInetAddressType is unknown(0) and cmgCurrentInetAddress is zero length.
cmgProcessorQos	1.3.6.1.4.1.6889.2.9.1.2.2
INT cmgQosControl	1.3.6.1.4.1.6889.2.9.1.2.2.1	INTEGER	read-only	Specifies whether this processor should use the locally administered Quality of Service parameters, or whether it should use the parameters downloaded from the controller. This affects both signaling and voice traffic.
INT cmgRemoteSigDscp	1.3.6.1.4.1.6889.2.9.1.2.2.2	INTEGER	read-only	DiffServ Code Point for signaling traffic on the H.248 link, received from the controller. If cmgQosControl is local(1), this value is ignored.
INT cmgRemoteSig802Priority	1.3.6.1.4.1.6889.2.9.1.2.2.3	INTEGER	read-only	802.1 Priority for signaling traffic on the H.248 link, received from the controller. If cmgQosControl is local(1), this value is ignored.
INT cmgLocalSigDscp	1.3.6.1.4.1.6889.2.9.1.2.2.4	INTEGER	read-write	DiffServ Code Point for signaling traffic on the H.248 link, locally administered. If cmgQosControl is remote(2), this value is ignored.
INT cmgLocalSig802Priority	1.3.6.1.4.1.6889.2.9.1.2.2.5	INTEGER	read-write	802.1 Priority for signaling traffic on the H.248 link, locally administered. If cmgQosControl is remote(2), this value is ignored.
INT cmgStatic802Vlan	1.3.6.1.4.1.6889.2.9.1.2.2.6	INTEGER	read-write	802.1 VLAN ID for this processor, locally administered. If cmgUseDhcpForVlan is on(1), this value is ignored.
INT cmgCurrent802Vlan	1.3.6.1.4.1.6889.2.9.1.2.2.7	INTEGER	read-only	802.1 VLAN ID currently in use for this processor. If cmgUseDhcpForVlan was on(1) at the last startup, this came from the DHCP server. Otherwise it is equal to cmgStatic802Vlan at the time of the last startup.
cmgProcessorClock	1.3.6.1.4.1.6889.2.9.1.2.3
STR cmgPrimaryClockSource	1.3.6.1.4.1.6889.2.9.1.2.3.1	DisplayString	read-write	Primary clock source configured for this processor. If a T1 or BRI module is providing the clock, it reads 'Vs' or 'Vs(pp,pp,...)', where s is slot number and pp are the port numbers. If the VoIP module is providing the clock, it reads 'voip'. It reads 'None' if no primary clock source is configured. If cmgClockSourceControl is remote(2), access is read-only. If cmgClockSourceControl is local(1), access is read-write.
STR cmgSecondaryClockSource	1.3.6.1.4.1.6889.2.9.1.2.3.2	DisplayString	read-write	Secondary clock source configured for this processor. If a T1 or BRI module is providing the clock, it reads 'Vs' or 'Vs(pp,pp,...)', where s is slot number and pp are the port numbers. If the VoIP module is providing the clock, it reads 'voip'. It reads 'None' if no secondary clock source is configured. If cmgClockSourceControl is remote(2), access is read-only. If cmgClockSourceControl is local(1), access is read-write.
INT cmgActiveClockSource	1.3.6.1.4.1.6889.2.9.1.2.3.3	INTEGER	read-write	Identifies the clock source in use at this processor. If cmgClockSourceControl is remote(2), access is read-only. If cmgClockSourceControl is local(1), access is read-write.
INT cmgClockSwitching	1.3.6.1.4.1.6889.2.9.1.2.3.4	INTEGER	read-write	A flag to enable/disable sync switching. If cmgClockSourceControl is remote(2), access is read-only. If cmgClockSourceControl is local(1), access is read-write.
INT cmgClockSourceControl	1.3.6.1.4.1.6889.2.9.1.2.3.5	INTEGER	read-only	Specifies whether this processor sync administration parameters are controlled locally or remotely.
cmgControllers	1.3.6.1.4.1.6889.2.9.1.3
INT cmgRegistrationState	1.3.6.1.4.1.6889.2.9.1.3.1	INTEGER	read-only	Shows whether this media gateway is currently registered with any call controller.
IP cmgActiveControllerAddress	1.3.6.1.4.1.6889.2.9.1.3.2	IpAddress	read-only	IPv4 Address of the call controller now serving this media gateway. If cmgRegistrationState is notRegistered(2), this will be '0.0.0.0'. If cmgRegistrationState is registered(1) and the controller IP address is IPv6 address, this will be '0.0.0.0'. Otherwise it will be taken from one of the two address lists at registration time.
INT cmgH248LinkStatus	1.3.6.1.4.1.6889.2.9.1.3.3	INTEGER	read-only	Status of the H.248 link connecting this media gateway to its active call controller.
I32 cmgH248LinkErrorCode	1.3.6.1.4.1.6889.2.9.1.3.4	Integer32	read-only	Most recently received H.248 error code affecting the link between this media gateway and its active call controller. If cmgH248LinkStatus is up(1), this value will be zero. 0 No error 400 Syntax error in message 403 Syntax error in TransactionRequest 406 Version not supported 410 Incorrect identifier 411 The transaction refers to an unknown ContextId 412 No ContextIDs available 421 Unknown action or illegal combination of actions 422 Syntax error in action 430 Unknown TerminationID 431 No TerminationID matched a wildcard 432 Out of TerminationIDs or No TerminationID available 433 TerminationID is already in a Context 434 Max number of Terminations in a Context exceeded 440 Unsupported or unknown package 441 Missing remote or local descriptor 442 Syntax error in command 443 Unknown command 444 Unsupported or unknown descriptor 445 Unsupported property 446 Unsupported or unknown parameter 447 Descriptor not legal in this command 448 Descriptor appears twice in a command 450 No such property in this package 451 No such event in this package 452 No such signal in this package 453 No such statistic in this package 454 No such parameter value in this package 455 Parameter illegal in this descriptor 456 Parameter or property appears twice in this descriptor 457 Missing parameter in signal or event 471 Implied add for multiplex failure 500 Internal software failure in the media gateway 501 Not implemented 502 Not ready 503 Service unavailable 504 Command received from unauthorized entity 505 Transaction Request received before ServiceChange Reply received 510 Insufficient resources 512 Gateway unequipped to detect requested event 513 Gateway unequipped to generate requested signal 514 Gateway cannot send the specified announcement 515 Unsupported media type 517 Unsupported or invalid mode 518 Event buffer full 519 Out of space to store digit map 520 Digit map undefined in MG 521 Termination is 'Service Changing' 526 Insufficient bandwidth 529 Internal hardware failure in MG 530 Temporary network failure 531 Permanent network failure 581 Does not exist
INT cmgUseDhcpForMgcList	1.3.6.1.4.1.6889.2.9.1.3.5	INTEGER	read-write	Should this gateway get its controller IP address from the DHCP server, or should it use the locally administered controller list? If this value is on(1), the gateway will try the DHCP-provided addresses first, and if they fail it will try the static addresses. If the value is off(2), the gateway will try only static addresses. Changes to this object take effect when the gateway is restarted.
STR cmgStaticControllerHosts	1.3.6.1.4.1.6889.2.9.1.3.6	DisplayString	read-write	Comma-separated list of up to four administered static IPv4 and IPv6 addresses for primary and backup call controllers. IPv4 addresses should be in the form '123.124.125.126', with no port numbers. (The Media Gateway always uses the default H.248 port number 2945). IPv6 address should be in the form of '2002:8740:64e2::8740:64e2'. Use '+' if there is both IPv4 and IPv6 address on the same index/location. An IP address may appear more than once in the list. If cmgUseDhcpForMgcList is equal to off(2), these are the only addresses the gateway will try. In that case this list must contain at least one active entry. Changes to the list take effect when the gateway is restarted. Example for IPv4 and IPv6 address configuration: '135.6.8.98+2001:db8::370:7334, 135.6.8.99, 2001:db8::1428:57ab'
STR cmgDhcpControllerHosts	1.3.6.1.4.1.6889.2.9.1.3.7	DisplayString	read-only	List of IP addresses for up to four primary and backup call controllers, received from the DHCP server. An IP address may appear more than once in the list. If cmgUseDhcpForMgcList is equal to on(2), the gateway will try these addresses first, and if none succeed, it will try the addresses in cmgStaticControllerHosts.
INT cmgPrimarySearchTime	1.3.6.1.4.1.6889.2.9.1.3.8	INTEGER	read-write	Number of minutes for the Primary Search Timer.
INT cmgTotalSearchTime	1.3.6.1.4.1.6889.2.9.1.3.9	INTEGER	read-write	Number of minutes for the Total Search Timer.
INT cmgTransitionPoint	1.3.6.1.4.1.6889.2.9.1.3.10	INTEGER	read-write	Value of the Transition Point.
STR cmgActiveControllerSoftwareVersion	1.3.6.1.4.1.6889.2.9.1.3.11	DisplayString	read-only	Release string of the call controller now serving this media gateway. Release string should be in format 'R015x.02.0.947.0' without patch information. If cmgRegistrationState is notRegistered(2) or this information is unknown to the agent, then this object will contain a zero-length string. Changes to the value take effect when the gateway is registered or re-registered.
IPt cmgActiveControllerInetAddressType	1.3.6.1.4.1.6889.2.9.1.3.12	InetAddressType	read-only	IPv4/IPv6 Address of the call controller now serving this media gateway. If cmgRegistrationState is notRegistered(2), this will be unknown(0). cmgActiveControllerAddress will present IPv4 address controller only.
IP cmgActiveControllerInetAddress	1.3.6.1.4.1.6889.2.9.1.3.13	InetAddress	read-only	The Inet Address of the controller that the gateway is registered to. 1. The address type of this object is specified in cmgActiveControllerInetAddressType. 2. Default of cmgActiveControllerInetAddressType is unknown(0) and cmgActiveControllerInetAddress is zero length.
cmgVoip	1.3.6.1.4.1.6889.2.9.1.4
INT cmgVoipEngineUseDhcp	1.3.6.1.4.1.6889.2.9.1.4.1	INTEGER	read-write	Determines whether VoIP engines use their statically administered IP addresses or whether they get their addresses from the DHCP server.
INT cmgVoipQosControl	1.3.6.1.4.1.6889.2.9.1.4.2	INTEGER	read-only	This is the same as cmgQosControl in the MG Processor group. That parameter determines whether the gateway uses voice and signaling QoS parameters administered locally or whether it gets the parameters from its call controller. It is reproduced here for convenience.
cmgVoipRemoteParameters	1.3.6.1.4.1.6889.2.9.1.4.3
cmgVoipRemoteQosParameters	1.3.6.1.4.1.6889.2.9.1.4.3.1
INT cmgVoipRemoteBbeDscp	1.3.6.1.4.1.6889.2.9.1.4.3.1.1	INTEGER	read-only	The Better-than-Best-Effort DiffServ code point received from the controller. This is a value to be assigned to the code point part of the Differentiated Services field in the IP header of each voice packet. See RFC2475 for a full description of Differentiated Services.
INT cmgVoipRemoteEfDscp	1.3.6.1.4.1.6889.2.9.1.4.3.1.2	INTEGER	read-only	The Expedited-Forwarding DiffServ code point received from the controller. This is a value to be assigned to the code point part of the Differentiated Services field in the IP header of each voice packet. See RFC2475 for a full description of Differentiated Services.
INT cmgVoipRemote802Priority	1.3.6.1.4.1.6889.2.9.1.4.3.1.3	INTEGER	read-only	The 802.1 priority received from the call controller. This is a priority value to be assigned to the tag header for priority-tagged voice frames. See IEEE standard 802.1Q-1998 for a full description.
INT cmgVoipRemoteMinRtpPort	1.3.6.1.4.1.6889.2.9.1.4.3.1.4	INTEGER	read-only	The lower end of the range of UDP ports assigned to voice traffic, received from the call controller. Must be less than or equal to cmgVoipRemoteMaxRtpPort.
INT cmgVoipRemoteMaxRtpPort	1.3.6.1.4.1.6889.2.9.1.4.3.1.5	INTEGER	read-only	The upper end of the range of UDP ports assigned to voice traffic, received from the call controller. Must be greater than or equal to cmgVoipRemoteMinRtpPort.
cmgVoipRemoteRtcpParameters	1.3.6.1.4.1.6889.2.9.1.4.3.2
INT cmgVoipRemoteRtcpEnabled	1.3.6.1.4.1.6889.2.9.1.4.3.2.1	INTEGER	read-only	A flag that determines whether the Media Gateway will collect and report RTCP statistics. See RFC 1889 for a full description of RTCP. If this value is disabled(2), the rest of this group will be ignored.
IP cmgVoipRemoteRtcpMonitorIpAddress	1.3.6.1.4.1.6889.2.9.1.4.3.2.2	IpAddress	read-only	The IPv4 address of an RTCP monitor to which the Media Gateway should report its RTCP statistics. cmgVoipRemoteRtcpMonitorIpAddress will present 0.0.0.0 if no IP address was configured or IPv6 address configured.
INT cmgVoipRemoteRtcpMonitorPort	1.3.6.1.4.1.6889.2.9.1.4.3.2.3	INTEGER	read-only	The port on the RTCP monitor to which the Media Gateway should report its RTCP statistics.
INT cmgVoipRemoteRtcpReportPeriod	1.3.6.1.4.1.6889.2.9.1.4.3.2.4	INTEGER	read-only	The RTCP reporting interval in seconds.
IPt cmgVoipRemoteRtcpMonitorInetAddressType	1.3.6.1.4.1.6889.2.9.1.4.3.2.5	InetAddressType	read-only	The IPv6 address type of an RTCP monitor to which the Media Gateway should report its RTCP statistics. User can define sending RTCP monitor packets to IPv4 host and IPv6 host. This mib item is used for IPv6 host, while cmgVoipRemoteRtcpMonitorIpAddress is used for the IPv4 host. cmgVoipRemoteRtcpMonitorIpAddress will present IPv4 address controller only.
IP cmgVoipRemoteRtcpMonitorInetAddress	1.3.6.1.4.1.6889.2.9.1.4.3.2.6	InetAddress	read-only	The IPv6 address of an RTCP monitor to which the Media Gateway should report its RTCP statistics. 1. The address type of this object is specified in cmgVoipRemoteRtcpMonitorInetAddressType. 2. Default of cmgVoipRemoteRtcpMonitorInetAddressType is unknown(0) and cmgVoipRemoteRtcpMonitorInetAddress is zero length.
INT cmgVoipRemoteRtcpMonitorPortInetAddress	1.3.6.1.4.1.6889.2.9.1.4.3.2.7	INTEGER	read-only	The port on the IPv6 RTCP monitor to which the Media Gateway should report its RTCP statistics.
cmgVoipRemoteRsvpParameters	1.3.6.1.4.1.6889.2.9.1.4.3.3
INT cmgVoipRemoteRsvpEnabled	1.3.6.1.4.1.6889.2.9.1.4.3.3.1	INTEGER	read-only	A flag that determines whether the VoIP engines should use RSVP to control call admission. See RFC 2205 for a full description of RSVP. If this value is disabled(2), the rest of this group will be ignored.
INT cmgVoipRemoteRetryOnFailure	1.3.6.1.4.1.6889.2.9.1.4.3.3.2	INTEGER	read-only	A flag that determines whether the VoIP engines should retry a reservation request after the first one fails. If this value is disabled(2), the next object will be ignored.
INT cmgVoipRemoteRetryDelay	1.3.6.1.4.1.6889.2.9.1.4.3.3.3	INTEGER	read-only	The interval in seconds between a reservation request failure and the subsequent retry. If cmgVoipRemoteRetryOnFailure is disabled(2), this object will be ignored.
INT cmgVoipRemoteRsvpProfile	1.3.6.1.4.1.6889.2.9.1.4.3.3.4	INTEGER	read-only	The RSVP service model to request.
cmgVoipLocalParameters	1.3.6.1.4.1.6889.2.9.1.4.4
cmgVoipLocalQosParameters	1.3.6.1.4.1.6889.2.9.1.4.4.1
INT cmgVoipLocalBbeDscp	1.3.6.1.4.1.6889.2.9.1.4.4.1.1	INTEGER	read-write	The Better-than-Best-Effort DiffServ code point received from the controller. This is a value to be assigned to the code point part of the Differentiated Services field in the IP header of each voice packet. See RFC2475 for a full description of Differentiated Services.
INT cmgVoipLocalEfDscp	1.3.6.1.4.1.6889.2.9.1.4.4.1.2	INTEGER	read-write	The Expedited-Forwarding DiffServ code point received from the controller. This is a value to be assigned to the code point part of the Differentiated Services field in the IP header of each voice packet. See RFC2475 for a full description of Differentiated Services.
INT cmgVoipLocal802Priority	1.3.6.1.4.1.6889.2.9.1.4.4.1.3	INTEGER	read-write	The 802.1 priority received from the call controller. This is a priority value to be assigned to the tag header for priority-tagged voice frames. See IEEE standard 802.1Q-1998 for a full description.
INT cmgVoipLocalMinRtpPort	1.3.6.1.4.1.6889.2.9.1.4.4.1.4	INTEGER	read-write	The lower end of the range of UDP ports assigned to voice traffic, received from the call controller. Must be less than or equal to cmgVoipLocalMaxRtpPort.
INT cmgVoipLocalMaxRtpPort	1.3.6.1.4.1.6889.2.9.1.4.4.1.5	INTEGER	read-write	The upper end of the range of UDP ports assigned to voice traffic, received from the call controller. Must be greater than or equal to cmgVoipLocalMinRtpPort.
cmgVoipLocalRtcpParameters	1.3.6.1.4.1.6889.2.9.1.4.4.2
INT cmgVoipLocalRtcpEnabled	1.3.6.1.4.1.6889.2.9.1.4.4.2.1	INTEGER	read-write	A flag that determines whether the Media Gateway will collect and report RTCP statistics. See RFC 1889 for a full description of RTCP. If this value is disabled(2), the rest of this group will be ignored.
IP cmgVoipLocalRtcpMonitorIpAddress	1.3.6.1.4.1.6889.2.9.1.4.4.2.2	IpAddress	read-write	The IPv4 address of an RTCP monitor to which the Media Gateway should report its RTCP statistics. cmgVoipLocalRtcpMonitorIpAddress will present 0.0.0.0 if no IP address was configured or IPv6 address configured.
INT cmgVoipLocalRtcpMonitorPort	1.3.6.1.4.1.6889.2.9.1.4.4.2.3	INTEGER	read-write	The port on the RTCP monitor to which the Media Gateway should report its RTCP statistics.
INT cmgVoipLocalRtcpReportPeriod	1.3.6.1.4.1.6889.2.9.1.4.4.2.4	INTEGER	read-write	The RTCP reporting interval in seconds.
IPt cmgVoipLocalRtcpMonitorInetAddressType	1.3.6.1.4.1.6889.2.9.1.4.4.2.5	InetAddressType	read-only	The IPv6 address type of an RTCP monitor to which the Media Gateway should report its RTCP statistics. User can define sending RTCP monitor packets to IPv4 host and IPv6 host. This mib item is used for IPv6 host, while cmgVoipLocalRtcpMonitorIpAddress is used for the IPv4 host. cmgVoipLocalRtcpMonitorIpAddress will present IPv4 address controller only.
IP cmgVoipLocalRtcpMonitorInetAddress	1.3.6.1.4.1.6889.2.9.1.4.4.2.6	InetAddress	read-only	The IPv6 address of an RTCP monitor to which the Media Gateway should report its RTCP statistics. 1. The address type of this object is specified in cmgVoipLocalRtcpMonitorInetAddressType. 2. Default of cmgVoipLocalRtcpMonitorInetAddressType is unknown(0) and cmgVoipLocalRtcpMonitorInetAddress is zero length.
INT cmgVoipLocalRtcpMonitorPortInetAddress	1.3.6.1.4.1.6889.2.9.1.4.4.2.7	INTEGER	read-write	The port on the IPv6 RTCP monitor to which the Media Gateway should report its RTCP statistics.
cmgVoipLocalRsvpParameters	1.3.6.1.4.1.6889.2.9.1.4.4.3
INT cmgVoipLocalRsvpEnabled	1.3.6.1.4.1.6889.2.9.1.4.4.3.1	INTEGER	read-write	A flag that determines whether the VoIP engines should use RSVP to control call admission. See RFC 2205 for a full description of RSVP. If this value is disabled(2), the rest of this group will be ignored.
INT cmgVoipLocalRetryOnFailure	1.3.6.1.4.1.6889.2.9.1.4.4.3.2	INTEGER	read-write	A flag that determines whether the VoIP engines should retry a reservation request after the first one fails. If this value is disabled(2), the next object will be ignored.
INT cmgVoipLocalRetryDelay	1.3.6.1.4.1.6889.2.9.1.4.4.3.3	INTEGER	read-write	The interval in seconds between a reservation request failure and the subsequent retry. If cmgVoipLocalRetryOnFailure is disabled(2), this object will be ignored.
INT cmgVoipLocalRsvpProfile	1.3.6.1.4.1.6889.2.9.1.4.4.3.4	INTEGER	read-write	The RSVP service model to request.
cmgVoipEngineTable	1.3.6.1.4.1.6889.2.9.1.4.5		not-accessible	Table of VoIP engines in the media gateway.
cmgVoipEngineEntry	1.3.6.1.4.1.6889.2.9.1.4.5.1		not-accessible	An entry in the table representing one VoIP engine.
INT cmgVoipSlot	1.3.6.1.4.1.6889.2.9.1.4.5.1.1	INTEGER	read-only	Location of this VoIP engine, either a media module slot (1-4 for G700) or the motherboard (100 for G700, 10 for G350, G250). For G450/G430 the index arrangement is as follows: * For V1 - V10 the rule is cmgVoIPSlot = Slot# * 10 + SoDIMM#. Note that MM760 is not supported in G430/G450, nor other MM which support VoIP engine. Thus, only V10 is relevant. * For G450 motherboard is 101-104. * For G430 motherboard is 101-102 (101 is the on board DSP and 102 is the replaceable VoIP SoDIMM module.
OCT cmgVoipMACAddress	1.3.6.1.4.1.6889.2.9.1.4.5.1.2	OCTET STRING	read-only	MAC address of the component hosting this VoIP engine.
IP cmgVoipStaticIpAddress	1.3.6.1.4.1.6889.2.9.1.4.5.1.3	IpAddress	read-write	Administered static IPv4 Address of this VoIP engine. If cmgVoipEngineUseDhcp was off(2) at startup time, this value determined the current IPv4 address of the engine.
IP cmgVoipCurrentIpAddress	1.3.6.1.4.1.6889.2.9.1.4.5.1.4	IpAddress	read-only	IPv4 Address currently in use at this VoIP engine. If cmgVoipEngineUseDhcp was on(2) at startup time, this value was received from the DHCP server. Otherwise it is equal to cmgVoipStaticIpAddress at startup time.
I32 cmgVoipJitterBufferSize	1.3.6.1.4.1.6889.2.9.1.4.5.1.5	Integer32	read-only	Size in bytes of the dynamic jitter buffer at this VoIP engine.
I32 cmgVoipTotalChannels	1.3.6.1.4.1.6889.2.9.1.4.5.1.6	Integer32	read-only	Total channels available to this VoIP engine.
I32 cmgVoipChannelsInUse	1.3.6.1.4.1.6889.2.9.1.4.5.1.7	Integer32	read-only	Number of channels in use at this VoIP engine.
INT cmgVoipAverageOccupancy	1.3.6.1.4.1.6889.2.9.1.4.5.1.8	INTEGER	read-only	5-minute average occupancy of this VoIP engine.
INT cmgVoipHyperactivity	1.3.6.1.4.1.6889.2.9.1.4.5.1.9	INTEGER	read-only	Indicates whether hyperactivity has been detected by this VoIP engine.
INT cmgVoipAdminState	1.3.6.1.4.1.6889.2.9.1.4.5.1.10	INTEGER	read-only	Maintenance busy-out state of this VoIP engine.
STR cmgVoipDspFWVersion	1.3.6.1.4.1.6889.2.9.1.4.5.1.11	DisplayString	read-only	Firmware version of the DSP complex on this VoIP engine. This is also available in the Load MIB.
INT cmgVoipDspStatus	1.3.6.1.4.1.6889.2.9.1.4.5.1.12	INTEGER	read-only	Status of the DSP complex on this VoIP engine.
INT cmgVoipEngineReset	1.3.6.1.4.1.6889.2.9.1.4.5.1.13	INTEGER	read-write	Setting the value of this attribute to ON is interpreted as a reset command for the VoIP engine. It initiates a complete reinitialisation of the VoIP engine.
OCT cmgVoipFaultMask	1.3.6.1.4.1.6889.2.9.1.4.5.1.14	OCTET STRING	read-only	Each bit of this value set to '1' indicates a specific fault in the VoIP engine. Octets are numbered in the order in which they appear in the PDU. Bits are numbered from the most-significant leftmost bit in the octet (bit 0) to the least-significant rightmost bit (bit 7). Cajun numbering continues across octets, so that octet 1 bit 0 is called bit 8 in the Cajun scheme. That number is also shown below, with the octet value for each single bit set. Cajun Octet Octet bit# bit# value Meaning ----- ----- ----- ------- 0 0/0 0x80 Occupancy above threshold, based on a snapshot of cmgVoipChannelsInUse divided by cmgVoipTotalChannels. 1 0/1 0x40 Occupancy above threshold, based on cmgVoipAverageOccupancy. 2 0/2 0x20 VoIP engine automatic reset. 3 0/3 0x10 VoIP hardware fault. 4 0/4 0x08 VoIP IP configuration fault. 5 0/5 0x04 VoIP DSP Failure 6 0/6 0x02 VoIP DSP CORE Failure 7 0/7 0x01 VoIP DSP FPGA Failure 8 1/0 0x80 Unsupported DSP module. 9--15 1/1-7 Unused
IPt cmgVoipStaticInetAddressType	1.3.6.1.4.1.6889.2.9.1.4.5.1.15	InetAddressType	read-only	Administered static IPv6 Address Type of the VoIP engine. The VoIP Engine Processor can have two IP addresses: one IPv4 and the second IPv6. cmgVoipStaticIpAddress presents the IPv4 address and this MIB item presents the IPv6 address.
IP cmgVoipStaticInetAddress	1.3.6.1.4.1.6889.2.9.1.4.5.1.16	InetAddress	read-only	Administered static IPv6 Address of the VoIP engine. 1. The address type of this object is specified in cmgVoipStaticInetAddressType. 2. Default of cmgVoipStaticInetAddressType is unknown(0) and cmgVoipStaticInetAddress is zero length.
IPt cmgVoipCurrentInetAddressType	1.3.6.1.4.1.6889.2.9.1.4.5.1.17	InetAddressType	read-only	IPv6 Address Type currently in use at this VoIP engine. The VoIP Engine Processor can have two IP address one IPv4 and the second IPv6. cmgVoipCurrentIpAddress presents the IPv4 address and this MIB item presents the IPv6 address.
IP cmgVoipCurrentInetAddress	1.3.6.1.4.1.6889.2.9.1.4.5.1.18	InetAddress	read-only	IPv6 Address currently in use at this VoIP engine. 1. The address type of this object is specified in cmgVoipCurrentInetAddressType. 2. Default of cmgVoipCurrentInetAddressType is unknown(0) and cmgVoipCurrentInetAddress is zero length.
cmgVoipDSPCoreTable	1.3.6.1.4.1.6889.2.9.1.4.6		not-accessible	Table representing the DSP cores in VoIP engine of the media gateway.
cmgVoipDSPCoreEntry	1.3.6.1.4.1.6889.2.9.1.4.6.1		not-accessible	An entry in the table representing one DSP Core of a VoIP engine. This table uses an external index from cmgVoIPEngineTable which selects a DSP SoDIMM/engine module and secondary index cmgDSPVoIPCoreID that selects a core on SoDIMM module
INT cmgDSPCoreCoreId	1.3.6.1.4.1.6889.2.9.1.4.6.1.1	INTEGER	read-only	The DSP core ID within the specific DSP VoIP engine.
INT cmgDSPCoreTotalChannels	1.3.6.1.4.1.6889.2.9.1.4.6.1.2	INTEGER	read-only	Total channels available to this DSP core.
INT cmgDSPCoreChannelsInUse	1.3.6.1.4.1.6889.2.9.1.4.6.1.3	INTEGER	read-only	Number of channels in use at this DSP core.
INT cmgDSPCoreAdminState	1.3.6.1.4.1.6889.2.9.1.4.6.1.4	INTEGER	read-write	Maintenance busy-out state of this DSP core.
INT cmgDSPCoreStatus	1.3.6.1.4.1.6889.2.9.1.4.6.1.5	INTEGER	read-only	Status of the DSP Core.
INT cmgDSPCoreDemandTest	1.3.6.1.4.1.6889.2.9.1.4.6.1.6	INTEGER	read-write	Activates on demand test for the DSP Core.
INT cmgDSPCoreDemandTestResult	1.3.6.1.4.1.6889.2.9.1.4.6.1.7	INTEGER	read-only	Result of the on demand test for the DSP Core.
INT cmgVoipEchoCancellerControl	1.3.6.1.4.1.6889.2.9.1.4.7	INTEGER	read-write	The echo canceller control setting for all VoIP engines. auto means that the system will enable or disable the echo cancellers as appropriate for each call. fixedOn indicates that the VoIP firmware always enables the echo cancellers (this value cannot be changed).
INT cmgVoipEchoCancellerConfig1	1.3.6.1.4.1.6889.2.9.1.4.8	INTEGER	read-write	Echo canceller configuration setting for all VoIP engines (byte 1 of 2). This value may not be writable if the VoIP firmware is old.
INT cmgVoipEchoCancellerConfig2	1.3.6.1.4.1.6889.2.9.1.4.9	INTEGER	read-write	Echo canceller configuration setting for all VoIP engines (byte 2 of 2). This value may not be writable if the VoIP firmware is old.
I32 cmgVoipTotalChannelsEnforcedByCM	1.3.6.1.4.1.6889.2.9.1.4.10	Integer32	read-only	Total channels enforced by Communications Manager.
cmgTraps	1.3.6.1.4.1.6889.2.9.1.5
cmgTrapManagerTable	1.3.6.1.4.1.6889.2.9.1.5.1		not-accessible	Table of trap receivers in this media gateway.
cmgTrapManagerEntry	1.3.6.1.4.1.6889.2.9.1.5.1.1		not-accessible	An entry in the table, representing a single trap receiver.
IP cmgTrapManagerAddress	1.3.6.1.4.1.6889.2.9.1.5.1.1.1	IpAddress	read-create	IP address of this trap receiver.
INT cmgTrapManagerControl	1.3.6.1.4.1.6889.2.9.1.5.1.1.3	INTEGER	read-create	Specifies whether this trap receiver is currently receiving traps.
I32 cmgTrapManagerMask	1.3.6.1.4.1.6889.2.9.1.5.1.1.4	Integer32	read-create	A bit mask indicating the trap categories of interest to this trap receiver. Bit Category 0 Power warnings 1 Fan and temperature warnings 2 Application faults 3 Module insert or remove 4 Configuration traps: port enable or disable, administrative busy-out and release for ports and media modules 5-7 Not supported 8 Voice faults: Quality of service problems, voice hardware faults 9 Normal operations: successful registration with the gateway controller, successful firmware download. 10-31 Not supported
ROW cmgTrapManagerRowStatus	1.3.6.1.4.1.6889.2.9.1.5.1.1.5	RowStatus	read-create	The status of this entry in the table. Available states: active(1), -- Trap receiver is administered, though not -- necessarily active. createAndGo(4), -- Used to add a new receiver to the table. destroy(6) -- Used to delete a receiver from the table. The cmgTrapManagerAddress of a new entry must be different from all other entries, or the create request will return INCONSISTENT-VALUE-ERROR.
cmgTrapDefinitions	1.3.6.1.4.1.6889.2.9.1.5.2
cmgTrapVariables	1.3.6.1.4.1.6889.2.9.1.5.2.1
STR cmgTrapLocation	1.3.6.1.4.1.6889.2.9.1.5.2.1.1	DisplayString	accessible-for-notify	Location of the problem in the form gggVspp, where ggg Media gateway number, or zero if the gateway is not currently registered with any controller. V The letter V; a field separator. s Slot number, if applicable. If the fault occurred on the media gateway processor, this will be omitted. pp Port number, if applicable. If the fault occurred on the media gateway processor or on a media module as a whole, this will be omitted.
STR cmgTrapOnBoard	1.3.6.1.4.1.6889.2.9.1.5.2.1.2	DisplayString	accessible-for-notify	Expected values are 'no' and 'yes'. If a problem is on-board, replacing the media module is likely to resolve the problem.
STR cmgTrapSubsystem	1.3.6.1.4.1.6889.2.9.1.5.2.1.3	DisplayString	accessible-for-notify	The high-level subsystem that generated the trap. Expected values are 'HW', 'SW', and 'Net'.
INT cmgTrapOnIccMissing	1.3.6.1.4.1.6889.2.9.1.5.2.1.4	INTEGER	read-write	Should the media gateway send a trap on startup if there is no integrated communications controller in slot 1?
STR cmgTrapModule	1.3.6.1.4.1.6889.2.9.1.5.2.1.5	DisplayString	accessible-for-notify	A display string to identify the module type in module insert and remove traps.
CMG cmgTrapSeverity	1.3.6.1.4.1.6889.2.9.1.5.2.1.6	CmgItuPerceivedSeverity	accessible-for-notify	The severity of the notification.
STR cmgProductId	1.3.6.1.4.1.6889.2.9.1.5.2.1.7	DisplayString	accessible-for-notify	The Product Id of Avaya Device - 10 characters.
I32 cmgTrapAvailableTimeslots	1.3.6.1.4.1.6889.2.9.1.5.2.1.8	Integer32	accessible-for-notify	Number of Timeslots available on this gateway.
I32 cmgTrapInUseTimeslots	1.3.6.1.4.1.6889.2.9.1.5.2.1.9	Integer32	accessible-for-notify	Number of Timeslots in use on this gateway.
INT cmgFipsErrorType	1.3.6.1.4.1.6889.2.9.1.5.2.1.10	INTEGER	accessible-for-notify	The type of FIPS error.
cmgTrapTypes	1.3.6.1.4.1.6889.2.9.1.5.2.2
cmgTrapV3separator	1.3.6.1.4.1.6889.2.9.1.5.2.2.0
NTF cmgMultipleFanFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.2			At least two fans have been operating at less than 90% of their nominal speed for five minutes or more. This may be an early warning of overheating.
NTF cmgMultipleFanClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.3			At least three fans are operating normally. The system should be operable indefinitely without overheating.
NTF cmgPsuFanBriefFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.4			The power supply fan has been operating at less than 90% of its optimal speed for 10 minutes or more, but less than 15 minutes. This may be an early warning of overheating.
NTF cmgPsuFanBriefClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.5			The power supply fan is operating normally.
NTF cmgPsuFanProlongedFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.6			The power supply fan has been operating at less than 90% of its optimal speed for 15 minutes or more. This may be an early warning of overheating.
NTF cmgPsuFanProlongedClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.7			The power supply fan is operating normally.
NTF cmgCpuTempWarningFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.10			The temperature sensor at the CPU has exceeded its warning threshold.
NTF cmgCpuTempWarningClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.11			The temperature sensor at the CPU has dropped below its warning threshold.
NTF cmgDspTempWarningFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.12			The temperature sensor at the DSP complex has exceeded its warning threshold.
NTF cmgDspTempWarningClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.13			The temperature sensor at the DSP complex has dropped below its warning threshold.
NTF cmgTempShutdownFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.14			The CPU temperature sensor has exceeded its shutdown threshold. The system is about to begin controlled shutdown.
NTF cmgMgpPowerFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.16			The voltage reading at the +5.1v power source serving the MG Processor is out of tolerance.
NTF cmgMgpPowerClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.17			The voltage reading at the +5.1v power source serving the MG Processor is back within its tolerance range.
NTF cmgMediaModulePowerFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.18			The voltage reading at the -48v power source serving the media modules is out of tolerance.
NTF cmgMediaModulePowerClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.19			The voltage reading at the -48v power source serving the media modules is back within its tolerance range.
NTF cmgVoipPowerFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.20			The voltage reading at the +3.4v power source serving the VoIP complexes is out of tolerance.
NTF cmgVoipPowerClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.21			The voltage reading at the +3.4v power source serving the VoIP complexes is back within its tolerance range.
NTF cmgDspPowerFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.22			The voltage reading at the +1.58v power source serving the DSP units is out of tolerance.
NTF cmgDspPowerClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.23			The voltage reading at the +1.58v power source serving the DSP units is back within its tolerance range.
NTF cmg8260PowerFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.24			The voltage reading at the +2.5v power source serving the 8260 processor is out of tolerance.
NTF cmg8260PowerClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.25			The voltage reading at the +2.5v power source serving the 8260 processor is back within its tolerance range.
NTF cmgAuxPowerFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.26			The voltage reading at the -48v auxiliary power source serving the end points is out of tolerance.
NTF cmgAuxPowerClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.27			The voltage reading at the -48v auxiliary power source serving the end points is back within its tolerance range.
NTF cmgFanPowerFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.28			The voltage at the +12 auxiliary power source serving the fans is out of tolerance.
NTF cmgFanPowerClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.29			The voltage at the +12 auxiliary power source serving the fans is back within its tolerance range.
NTF cmgSyncSignalFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.30			Synchronization signal lost.
NTF cmgSyncSignalClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.31			Synchronization signal normal.
NTF cmgVoipHardwareFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.32			One or more of the DSP complexes serving VoIP engines has failed.
NTF cmgVoipHardwareClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.33			All the DSP complexes serving VoIP engines are back in service.
NTF cmgSyncSignalWarn	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.34			Synchronization signal lost.
NTF cmgSyncWarnClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.35			Synchronization signal normal.
NTF cmgSyncSignalExcess	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.36			The synchronization signal source (primary or secondary) is experiencing excessive failures in a short period of time causing excessive switching to an alternate source.
NTF cmgSyncExcessClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.37			Synchronization signal source which was causing excessive switching due to excessive failures is now normal.
NTF cmgVoipCoreFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.38			One or more of the DSP Cores serving VoIP engines has failed.
NTF cmgVoipCoreClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.39			All the DSP Cores serving VoIP engines are back in service.
NTF cmgModuleRemove	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.50			A media module has been removed.
NTF cmgModuleInsertFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.52			Media module insertion sequence has failed.
NTF cmgModuleInsertSuccess	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.53			A media module has been inserted.
NTF cmgMgBusyout	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.54			An administrator has moved a media module or port to the busy-out state.
NTF cmgMgRelease	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.55			An administrator has moved a media module or port from the busy-out state back into service.
NTF cmgUnsupportedMmEnrolement	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.56			The event is sent when a module is inserted to a slot where it can be identified but not supported due to hardware limitations.
NTF cmgDataModuleAwohConflict	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.57			This event is generated when a data module is found in a slot that was Administered without hardware as a voice module in the call controller.
NTF cmgFirmwareDownloadBegun	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.70			The media gateway has begun download of a software module.
NTF cmgFirmwareDownloadSuccess	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.71			The media gateway has completed successful download of a software module.
NTF cmgRegistrationSuccess	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.73			The media gateway has successfully registered with a controller.
NTF cmgMgManualReset	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.74			The media gateway is beginning a user-requested reset operation.
NTF cmgModuleManualReset	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.75			A media module is beginning a user-requested reset operation.
NTF cmgVoipManualReset	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.76			A VoIP engine is beginning a user-requested reset operation.
NTF cmgDsuManualReset	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.77			An E1/T1 DSU is beginning a user-requested reset operation.
NTF cmgConfigUploadBegun	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.78			The media gateway has begun upload of a configuration file.
NTF cmgConfigUploadSuccess	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.79			The media gateway has completed successful upload of a configuration file.
NTF cmgMemoryFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.90			Main processor memory has issued a failure warning.
NTF cmgMemoryClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.91			Main processor memory is back in normal service.
NTF cmgDhcpRequestFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.92			The media gateway cannot contact its DHCP server, or the server failed to respond to a request.
NTF cmgDhcpRequestClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.93			The media gateway has received a successful response to a DHCP request.
NTF cmgFirmwareDownloadFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.94			An attempt to download a software module has failed.
NTF cmgProcessRestart	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.96			One or more media gateway software processes have terminated and been restarted by the software task manager.
NTF cmgProcessRestartClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.97			Media gateway software processes are running normally.
NTF cmgIccMissingFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.98			An Internal Communications Controller expected in slot 1 is missing.
NTF cmgIccMissingClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.99			The Internal Communications Controller expected in slot 1 is present.
NTF cmgIccAutoReset	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.100			The Media gateway has automatically reset the Internal Communications Controller.
NTF cmgIccAutoResetClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.101			The Internal Communications Controller is running normally.
NTF cmgPrimaryControllerFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.102			The media gateway cannot contact the first controller in its controller list.
NTF cmgPrimaryControllerClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.103			The media gateway has successfully contacted the first controller in its controller list.
NTF cmgNoControllerFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.104			The media gateway cannot contact any controller in its controller lists.
NTF cmgNoControllerClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.105			The media gateway has successfully contacted one of the controllers in its controller lists.
NTF cmgRegistrationFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.106			The media gateway cannot register with any controller in its controller list.
NTF cmgH248LinkDown	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.108			The H.248 link between the media gateway and its controller is down.
NTF cmgH248LinkUp	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.109			The H.248 link between the media gateway and its controller is back in service.
NTF cmgTestFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.110			A maintenance test has failed.
NTF cmgTestClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.111			Failed maintenance tests have succeeded.
NTF cmgTestThresholdFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.112			Maintenance test failure count has exceeded its reporting threshold.
NTF cmgTestThresholdClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.113			Maintenance test failure count has dropped below its reporting threshold.
NTF cmgMgAutoReset	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.114			The media gateway is beginning automatic reinitialization.
NTF cmgModuleAutoReset	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.116			One of the media modules is beginning automatic reinitialization.
NTF cmgModuleAutoResetClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.117			The reset media module is running normally.
NTF cmgModulePostFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.118			A media module has failed its power-on startup test.
NTF cmgModulePostClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.119			Media module power-on startup test successful.
NTF cmgModuleParameterFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.120			A media module has failed its parameter exchange.
NTF cmgModuleParameterClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.121			Media module parameter exchange successful.
NTF cmgConfigUploadFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.122			An attempt to upload a configuration file has failed.
NTF cmgVoipOccFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.124			One or more of the VoIP engines in the media gateway is over its occupancy threshold, as measured by a snapshot: (Channels In Use)/(Total Channels).
NTF cmgVoipOccClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.125			All the VoIP engines in the media gateway are operating below occupancy threshold, as measured by a snapshot: (Channels In Use)/(Total Channels).
NTF cmgVoipAvgOccFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.126			One or more of the VoIP engines in the media gateway is over its average occupancy threshold.
NTF cmgVoipAvgOccClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.127			All the VoIP engines in the media gateway are operating below occupancy threshold, as measured by a snapshot: (Channels In Use)/(Total Channels).
NTF cmgVoipAutoReset	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.128			A VoIP engine has begun automatic reset.
NTF cmgVoipAutoResetClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.129			A VoIP engine has completed automatic reset, and is running normally.
NTF cmgDsuFpgaConfigureFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.130			The DSU in one of the E1/T1 media modules failed to configure its Field Programmable Gateway Array.
NTF cmgDsuFpgaConfigureClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.131			The DSU in one of the E1/T1 media modules has successfully configured its Field Programmable Gateway Array.
NTF cmgDsuAutoReset	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.132			A DSU in one of the E1/T1 media modules has begun automatic reset.
NTF cmgDsuAutoResetClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.133			A DSU in one of the E1/T1 media modules has completed automatic reset, and is running normally.
NTF cmgDsuDteDtrFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.134			One of the E1/T1 media modules has detected that the DTR signal from its DTE is off. This indicates that the DTE is not connected or not functioning.
NTF cmgDsuDteDtrClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.135			One of the E1/T1 media modules has detected that the DTR signal from its DTE is back to normal.
NTF cmgDsuDteRtsFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.136			An E1/T1 media module has detected that the RTS signal from its DTE is not on whenever the DTE requests to send data and during data transfer. This indicates that the DTE is not functioning.
NTF cmgDsuDteRtsClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.137			An E1/T1 media module has detected that the RTS signal from its DTE is back to normal.
NTF cmgDsuTxDFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.138			An E1/T1 media module has detected that the data received from the local DTE to be sent to the far end is either all ones or all zeroes.
NTF cmgDsuTxDClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.139			The E1/T1 media module is receiving normal data from the local DTE to be sent to the far end.
NTF cmgDsuRxDFailure	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.140			An E1/T1 media module has detected that the data received from the far end to be sent to the local DTE is either all ones or all zeroes.
NTF cmgDsuRxDClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.141			The E1/T1 media module is receiving normal data from the far end to be sent to the local DTE.
NTF cmgVoipIpConfigFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.142			There is an IP configuration failure in the VoIP Engine. No static IP address has been supplied or the firmware is getting indications that this is a duplicate IP address.
NTF cmgVoipIpConfigClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.143			The IP configuration of the VoIP Engine is successful.
NTF cmgConfigDownloadFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.144			An attempt to download a configuration file has failed.
NTF cmgConfigDownloadBegun	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.145			The media gateway has begun download of a configuration file.
NTF cmgConfigDownloadSuccess	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.146			The media gateway has completed successful download of a configuration file.
NTF cmgTimeslotOccupancyFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.147			Timeslot usage is over the occupancy threshold, as measured by a snapshot: (Timeslots In Use)/(Total Timeslots).
NTF cmgTimeslotOccupancyClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.148			Timeslot usage is below the occupancy threshold, as measured by a snapshot: (Timeslots In Use)/(Total Timeslots).
NTF cmgTimeslotAvailabilityFault	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.149			No more Timeslot are available on this gateway.
NTF cmgTimeslotAvailabilityClear	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.150			Timeslots are again available on this gateway, usage is below the occupancy threshold, as measured by a snapshot: (Timeslots In Use)/(Total Timeslots).
NTF cmgRegistrationSuccessInetAddress	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.151			The media gateway has successfully registered with a controller. This trap is identical to cmgRegistrationSuccess but with INET Address varbind instead of IPv4 varbind.
NTF cmgRegistrationFaultInetAddress	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.152			The media gateway cannot register with any controller in its controller list. This trap is identical to cmgRegistrationFault but with INET Address varbind instead of IPv4 varbind.
NTF cmgDs1Layer2Down	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.153			ISDN Layer-2 is down on a Ds1.
NTF cmgDs1Layer2Up	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.154			ISDN Layer-2 is established on a Ds1.
NTF cmgFipsErrorMode	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.155			The Gateway is in FIPS error mode.
NTF cmgCertErrorCertRevoked	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.156			A Gateway TLS Certificate was revoked.
NTF cmgCrlAccessDenied	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.157			The Gateway could not access a Certificate Revocation List.
NTF cmgCrlFileSize	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.158			The Gateway could not download a Certificate Revocation List due to filesystem limitations.
NTF cmgCertErrorCertExpired	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.159			A Gateway TLS Certificate has expired.
NTF cmgCertErrorNearExpiry	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.160			A Gateway TLS Certificate is near expiry and should be updated.
NTF cmgCertErrorIdAuthentication	1.3.6.1.4.1.6889.2.9.1.5.2.2.0.161			A Gateway TLS Certificate could not be authenticated
NTF cmgFirmwareDownloadWarning	1.3.6.1.4.1.6889.2.9.1.5.2.2.95			Non critical event occur during attempt to download a software module.
cmgContactClosures	1.3.6.1.4.1.6889.2.9.1.6
cmgContactClosuresTable	1.3.6.1.4.1.6889.2.9.1.6.1		not-accessible	This table is used for managing contact closure adjunct port. The adjunct box contains two relays.
cmgContactClosuresEntry	1.3.6.1.4.1.6889.2.9.1.6.1.1		not-accessible
INT cmgCcModule	1.3.6.1.4.1.6889.2.9.1.6.1.1.1	INTEGER	read-only
INT cmgCcPort	1.3.6.1.4.1.6889.2.9.1.6.1.1.2	INTEGER	read-only
INT cmgCcRelay	1.3.6.1.4.1.6889.2.9.1.6.1.1.3	INTEGER	read-only	Each contact closure port can control two relays on the adjunct
INT cmgCcAdminState	1.3.6.1.4.1.6889.2.9.1.6.1.1.4	INTEGER	read-write	The admin state of the contact-closure where: Auto(1): The Contact Closure is controlled by the call Controller. Trigger(2): The contact closure relay is triggered. Off(3): The contact closure relay is off (not triggered).
INT cmgCcPulseDuration	1.3.6.1.4.1.6889.2.9.1.6.1.1.5	INTEGER	read-write	The number of second the relay is triggred after each pulse activation signal is received from the call-controller.
INT cmgCcStatus	1.3.6.1.4.1.6889.2.9.1.6.1.1.6	INTEGER	read-only	The actual contact closure relay state
cmgETR	1.3.6.1.4.1.6889.2.9.1.7
cmgETRTable	1.3.6.1.4.1.6889.2.9.1.7.1		not-accessible	Emergency Transfer Function Table (short circuit Line and Trunk ports in case of call-controller connectivity problems)
cmgETREntry	1.3.6.1.4.1.6889.2.9.1.7.1.1		not-accessible
INT cmgEtrModule	1.3.6.1.4.1.6889.2.9.1.7.1.1.1	INTEGER	read-only	Module number - 10 on G450
INT cmgEtrAdminState	1.3.6.1.4.1.6889.2.9.1.7.1.1.2	INTEGER	read-write	Module's ETR administration state where: off(1): ETR is turned off without checking if there is an active call among trunk-line port pairs auto(2): ETR is turned off as soon as the module is operational (controlled by a call controller) on(3): ETR is never turned off
INT cmgEtrNumberOfPairs	1.3.6.1.4.1.6889.2.9.1.7.1.1.3	INTEGER	read-only	The number of ETR TRUNK-LINE pairs
INT cmgEtrStatus	1.3.6.1.4.1.6889.2.9.1.7.1.1.4	INTEGER	read-only	The current status of the ETR function
OCT cmgEtrCurrentLoopDetect	1.3.6.1.4.1.6889.2.9.1.7.1.1.5	OCTET STRING	read-write	Each bit in the bit-mask represents a current-loop-detector of one trunk-line ETR pairs. The bit is set when current is detected
cmgDynamicCAC	1.3.6.1.4.1.6889.2.9.1.8
INT cmgDynCacStatus	1.3.6.1.4.1.6889.2.9.1.8.1	INTEGER	read-only	Dynamic CAC status
I32 cmgDynCacRBBL	1.3.6.1.4.1.6889.2.9.1.8.2	Integer32	read-only	The last Reported BBL value sent to the MGC
TIK cmgDynCacLastUpdate	1.3.6.1.4.1.6889.2.9.1.8.3	TimeTicks	read-only	The last time (sysUpTime) a 'dynamic CAC' event was sent to the MGC
cmgSLAMonitor	1.3.6.1.4.1.6889.2.9.1.9
INT cmgSLAMonitorState	1.3.6.1.4.1.6889.2.9.1.9.1	INTEGER	read-write	The current state of the SLA Monitor.
IPt cmgSLAMonitorServerInetAddressType	1.3.6.1.4.1.6889.2.9.1.9.2	InetAddressType	read-only	The IP address type (IPv4 or IPv6) of this SLA Monitor server.
IP cmgSLAMonitorServerInetAddress	1.3.6.1.4.1.6889.2.9.1.9.3	InetAddress	read-only	The IPv4 or IPv6 address of the SLA Monitor server.
INT cmgSLAMonitorServerPort	1.3.6.1.4.1.6889.2.9.1.9.4	INTEGER	read-only	The SLA Monitor server port.
INT cmgSLAMonitorPacketCaptureMode	1.3.6.1.4.1.6889.2.9.1.9.10	INTEGER	read-write	The SLA Monitor packet capture mode.
STR cmgSLAMonitorVersion	1.3.6.1.4.1.6889.2.9.1.9.99	DisplayString	read-only	The SLA Monitor firmware version.

RFC description

Vendor-private MIB for Polycom G700 media gateway; manages media gateway call control, signaling, and RTP stream configuration.

Start monitoring Avaya G700/G450/G350 H.248 Media Gateway with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download G700-MG-MIB

What Is G700-MG-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description