All MIBs › Fore-TCM-MIB
Organization: FORE
Last Updated: 1999-11-05
Category: ATM, Vendor: Fore Systems (ATM)
Description: Fore Systems TCM (Tandem Connection Monitoring) MIB providing ATM OAM tandem connection monitoring configuration and performance objects.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Fore-TCM-MIB?
Fore-TCM-MIB, despite its name referencing Tandem Connection Monitoring, actually documents Fore Systems' ECP (Embedded Control Processor) Timing Control Module hardware, covering board identification and serial interface configuration. It exposes hardware inventory data (board version, serial number, presence of a redundant ECP or ESI companion board) plus serial port configuration (port type and speed) and software version group objects. This makes it a hardware/software inventory and presence-monitoring MIB, useful for confirming board revision, serial number for asset tracking, whether expected companion hardware (a secondary ECP or ESI module) is actually installed, and the running firmware version. It has no apparent dependency on external standard MIBs, being a self-contained vendor hardware descriptor. It is deployed on ForeRunner ATM switches to give operators visibility into the timing/control board's identity and health during hardware audits or troubleshooting. Network engineers evaluating or troubleshooting this functionality can download the Fore-TCM-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in Fore-TCM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Fore Systems ForeRunner ATM switch (ECP/Timing Control Module)
Monitoring Examples
An administrator would read ecpBoardVersion and ecpBoardSerialNumber from ecpBoardTable during an asset inventory, and check ecpBoardOtherEcpPresent/ecpBoardEsiPresent to confirm a redundant control board is actually detected by the chassis. ecpSerialIfPortType and ecpSerialIfPortSpeed in ecpSerialIfTable would be checked when a serial management or timing link is misbehaving to confirm it is configured at the expected speed. ecpSoftware would be polled to verify the running firmware version matches the expected release after an upgrade.
What Can Be Monitored
- board version and serial number
- redundant ECP/ESI presence
- serial interface port type and speed
- running software version
This MIB depends on
Related MIBs
Imported Objects
From Fore-Common-MIB
| EntryStatus | |
| atmSwitch | OBJECT-IDENTITY |
| hardware | OBJECT-IDENTITY |
From Fore-TrapLog-MIB
| trapLogIndex | OBJECT-TYPE |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| PhysAddress | |
| TimeInterval |
How to Use in IPNetwork Monitor
Example using ecpNetIfInOctets OID:
Select a Fore Systems (later Marconi) ForeRunner ATM switch (ECP Timing Control Module hardware) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type ecpNetIfInOctets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of octets received on the interface, including framing characters. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| NTF ecpOperatingModeChange | 1.3.6.1.4.1.326.2.2.0.1050 | This trap indicates that the Extended Control Processor (ECP) has change operating state. | ||
| NTF esiTimingSourceChange | 1.3.6.1.4.1.326.2.2.0.1051 | This trap is generated whenever the External Synchronization Interface (ESI) timing source (esiCurrentTimingRef) is changed either manually or by the system due to failure detection. | ||
| NTF esiTimingSourceFailed | 1.3.6.1.4.1.326.2.2.0.1052 | This trap is generated whenever the External Synchronization Interface (ESI) timing source (esiCurrentTimingRef) fails. | ||
| NTF ecpStandbyFailed | 1.3.6.1.4.1.326.2.2.0.1076 | This trap is generated whenever the Standby Timing Control Module (TCM) appears to haved failed. This is determined by lack of response from it. | ||
| ecpStationModule | 1.3.6.1.4.1.326.2.2.1.7 | The Timing Control Module (TCM). | ||
| ecpHardware | 1.3.6.1.4.1.326.2.2.1.7.1 | |||
| ecpBoardTable | 1.3.6.1.4.1.326.2.2.1.7.1.1 | not-accessible | This table contains Extended Control Processor (ECP) board information. | |
| ecpBoardEntry | 1.3.6.1.4.1.326.2.2.1.7.1.1.1 | not-accessible | This entry contains Extended Control Processor (ECP) board information | |
| INT ecpBoardIndex | 1.3.6.1.4.1.326.2.2.1.7.1.1.1.1 | INTEGER | read-only | This is the Extended Control Processor board index within the management station. |
| I32 ecpBoardVersion | 1.3.6.1.4.1.326.2.2.1.7.1.1.1.2 | Integer32 | read-only | This is the version number of this Extended Control Processor (ECP) board. |
| I32 ecpBoardSerialNumber | 1.3.6.1.4.1.326.2.2.1.7.1.1.1.3 | Integer32 | read-only | This is the serial number of this Extended Control Processor (ECP) board. |
| INT ecpBoardOtherEcpPresent | 1.3.6.1.4.1.326.2.2.1.7.1.1.1.4 | INTEGER | read-only | This is the other ECP board present indicator for this Extended Control Processor (ECP) board. |
| INT ecpBoardEsiPresent | 1.3.6.1.4.1.326.2.2.1.7.1.1.1.5 | INTEGER | read-only | This is the External Synchronization Interface (ESI) present indicator for this Extended Control Processor (ECP) board. |
| ecpSerialIfTable | 1.3.6.1.4.1.326.2.2.1.7.1.2 | not-accessible | This table contains the serial port interface information for the Extended Control Processor (ECP) board. | |
| ecpSerialIfEntry | 1.3.6.1.4.1.326.2.2.1.7.1.2.1 | not-accessible | This entry contains the serial port interface information for the Extended Control Processor (ECP) board. | |
| I32 ecpSerialIfPortIndex | 1.3.6.1.4.1.326.2.2.1.7.1.2.1.1 | Integer32 | read-only | This is the serial port interface index for this port on the Extended Control Processor (ECP) board. |
| INT ecpSerialIfPortType | 1.3.6.1.4.1.326.2.2.1.7.1.2.1.2 | INTEGER | read-only | This is the serial port interface type for this port on the Extended Control Processor (ECP) board. |
| I32 ecpSerialIfPortSpeed | 1.3.6.1.4.1.326.2.2.1.7.1.2.1.3 | Integer32 | read-only | This is the serial port interface speed for this port on the Extended Control Processor (ECP) board. |
| INT ecpSerialIfFlowType | 1.3.6.1.4.1.326.2.2.1.7.1.2.1.4 | INTEGER | read-only | This is the serial port interface flow control for this port on the Extended Control Processor (ECP) board. |
| I32 ecpSerialIfPortBits | 1.3.6.1.4.1.326.2.2.1.7.1.2.1.5 | Integer32 | read-only | This is the serial port interface character size for this port on the Extended Control Processor (ECP) board. |
| INT ecpSerialIfPortStopBits | 1.3.6.1.4.1.326.2.2.1.7.1.2.1.6 | INTEGER | read-only | This is the serial port interface stop bit count for this port on the Extended Control Processor (ECP) board. |
| INT ecpSerialIfPortParity | 1.3.6.1.4.1.326.2.2.1.7.1.2.1.7 | INTEGER | read-only | This is the serial port interface character parity for this port on the Extended Control Processor (ECP) board. |
| ecpEnvironment | 1.3.6.1.4.1.326.2.2.1.7.1.3 | |||
| ecpAlarmGroup | 1.3.6.1.4.1.326.2.2.1.7.1.3.1 | |||
| ecpAlarmTable | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1 | not-accessible | A table of switch alarm definitions and configuration. | |
| ecpAlarmEntry | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1 | not-accessible | A table entry containing switch alarm definitions. | |
| INT ecpAlarmType | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1.1 | INTEGER | read-only | The type of the alarm. |
| INT ecpAlarmStatus | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1.2 | INTEGER | read-only | The status of this alarm entry. An alarm becomes active if the underlying condition is detected. For power supplies, the input failed alarm condition is asserted if the input voltage is not within the nominal range for the supply. This does not necessarily mean that an ouput failure will result. A power supply output failure condition is asserted if any power supply is failing or if it is physically removed. Power supply output alarms are only applicable to switches with multiple power supplies. Fan bank and temperature sensor failures are applicable only to switches with the appropriate sensing capabilities. Link and spans failures are applicable to all switches. |
| INT ecpAlarmMinorCategory | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1.3 | INTEGER | read-write | This object indicates whether a minor alarm is triggered when this event occurs. |
| INT ecpAlarmMajorCategory | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1.4 | INTEGER | read-write | This object indicates whether a major alarm is triggered when this event occurs. |
| I32 ecpAlarmReset | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1.5 | Integer32 | read-write | The manager may set this to the value zero to cancel a current alarm. This is useful for silencing alarms triggered via edge detection. If this variable is readable, then the alarm is resettable. |
| INT ecpAlarmMajorRelayState | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.2 | INTEGER | read-only | This object indicates the current state of the major alarm relay. If one or more of the alarms (ecpAlarmType) that are defined major (ecpAlarmMajorCategory) are currently active (ecpAlarmStatus), this object will be on(1). |
| INT ecpAlarmMinorRelayState | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.3 | INTEGER | read-only | This object indicates the current state of the minor alarm relay. Ifone or mote of the alarms (ecpAlarmType) that are defined minor (ecpAlarmMinorCategory) are currently active (ecpAlarmStatus), this object will be on(1). |
| ecpAlarmRelayTable | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.4 | not-accessible | This table contains the alarm relay definitions for the Extended Control Processor (ECP) board. | |
| ecpAlarmRelayEntry | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.4.1 | not-accessible | This entry contains the alarm relay definitions for the Extended Control Processor (ECP) board. | |
| I32 ecpAlarmRelayIndex | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.4.1.1 | Integer32 | read-only | This is the index of the alarm relay on the Extended Control Processor (ECP). The Raven ECP has 5 addressable alarm relays (1-5). |
| INT ecpAlarmRelayFunction | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.4.1.2 | INTEGER | read-write | This is the alarm function associated with an alarm relay on the Extended Control Processor (ECP). An alarm relay may either be unused, assigned to the major alarm, or assigned to the minor alarm. |
| INT ecpAlarmRelayState | 1.3.6.1.4.1.326.2.2.1.7.1.3.1.4.1.3 | INTEGER | read-only | This is the current state of the alarm relay on the Extended Control Processor (ECP). The state 'on' means that the alarm relay is activated; the state 'off' means that it is deactivated. |
| ecpSoftware | 1.3.6.1.4.1.326.2.2.1.7.2 | |||
| ecpSwMainGroup | 1.3.6.1.4.1.326.2.2.1.7.2.1 | |||
| ecpSwMainTable | 1.3.6.1.4.1.326.2.2.1.7.2.1.1 | not-accessible | The table contains the Extended Control Processor (ECP) information maintained by the control software. | |
| ecpSwMainEntry | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1 | not-accessible | This entry contains the Extended Control Processor (ECP) information maintained by the control software. | |
| STR ecpName | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.1 | DisplayString | read-write | This is the system name of this Extended Control Processor (ECP) platform. |
| I32 ecpHardwareVersion | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.2 | Integer32 | read-only | This is the hardware version of the Extended Control Processor (ECP) platform. |
| I32 ecpSoftwareVersion | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.3 | Integer32 | read-only | This is the software version of the Extended Control Processor (ECP) control software. The version is encoded into 6 hex characters. Version 1.2.3 would be 0x010203. |
| STR ecpSoftwareVersionText | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.4 | DisplayString | read-only | This is the software version text of the Extended Control Processor (ECP) control software. This object contains information regarding the software configuration that was used to build this software. |
| INT ecpType | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.5 | INTEGER | read-only | This is the type of the Extended Control Processor (ECP) board. |
| INT ecpOperatingStatus | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.6 | INTEGER | read-only | This is the software status of this Extended Control Processor (ECP). |
| INT ecpProtocolType | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.7 | INTEGER | read-write | The transfer protocol that is used when upgrading the software, saving/restoring the CDB, etc. on this Extended Control Processor (ECP) board. |
| STR ecpTimeZone | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.8 | DisplayString | read-write | The TimeZone configured for this Extended Control Processor (ECP). This variable follows the POSIX standard 1003.1-1988 for the format of the TZ environment variable. In particular, it is general enough to specify the rules for converting from Standard to Daylight Savings time for most timezones of the world. By default, the ECP has the rules built in for the following timezones: EST5EDT CST6CDT MST7MDT PST8PDT AKST9AKDT. Locales outside of these timezones will need to supply the appropriate rule for switching between Daylight and Standard time. |
| DAT ecpGMTime | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.9 | DateAndTime | read-write | The Extended Control Processor's (ECP's) notion of Greenwich Mean Time. Linked to hrSystemDate. Offset part of time spec, if supplied, is considered an error. |
| TIK ecpUptime | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.10 | TimeTicks | read-only | This is the amount of time that the Extended Control Processor (ECP) control software has been running, in hundredths of a second. |
| DAT ecpModeChangeTime | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.11 | DateAndTime | read-only | This is the time that the Extended Control Processor (ECP) control software has switched to the current operating mode. |
| INT ecpOtherEcpStatus | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.12 | INTEGER | read-only | This is the software status of the other Extended Control Processor (ECP) from the viewpoint of this ECP. |
| INT ecpExternalInput1 | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.13 | INTEGER | read-only | This is the state of External Input #1 from the viewpoint of the Extended Control Processor (ECP). |
| INT ecpExternalInput2 | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.14 | INTEGER | read-only | This is the state of External Input #2 from the viewpoint of the Extended Control Processor (ECP). |
| INT ecpExternalInput3 | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.15 | INTEGER | read-only | This is the state of External Input #3 from the viewpoint of the Extended Control Processor (ECP). |
| INT ecpExternalInput4 | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.16 | INTEGER | read-only | This is the state of External Input #4 from the viewpoint of the Extended Control Processor (ECP). |
| INT ecpExternalInput5 | 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.17 | INTEGER | read-only | This is the state of External Input #5 from the viewpoint of the Extended Control Processor (ECP). |
| ecpIpGroup | 1.3.6.1.4.1.326.2.2.1.7.2.2 | |||
| ecpNetIfTable | 1.3.6.1.4.1.326.2.2.1.7.2.2.1 | not-accessible | This table contains the network interface information for the Extended Control Processor (ECP) board. | |
| ecpNetIfEntry | 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1 | not-accessible | This entry contains the network interface information for the Extended Control Processor (ECP) board. | |
| I32 ecpNetIfIndex | 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.1 | Integer32 | read-only | A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization. |
| STR ecpNetIfDescr | 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.2 | DisplayString | read-only | A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface. |
| PHY ecpNetIfPhysAddress | 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.3 | PhysAddress | read-only | The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length. |
| INT ecpNetIfAdminStatus | 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.4 | INTEGER | read-write | The desired state of the interface. |
| INT ecpNetIfOperStatus | 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.5 | INTEGER | read-only | The current operational state of the interface. |
| TIK ecpNetIfLastChange | 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.6 | TimeTicks | read-only | The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value. |
| IP ecpNetIfIpAddr | 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.7 | IpAddress | read-write | The IP address associated with this network interface. |
| IP ecpNetIfIpMask | 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.8 | IpAddress | read-write | The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0. |
| I32 ecpNetIfIpBcastAddr | 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.9 | Integer32 | read-write | The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface. |
| ecpNetIfStatsTable | 1.3.6.1.4.1.326.2.2.1.7.2.2.2 | not-accessible | This table contains the network interface statistics for the Extended Control Processor (ECP) board. | |
| ecpNetIfStatsEntry | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1 | not-accessible | This entry contains the network interface statistics for the Extended Control Processor (ECP) board. | |
| C32 ecpNetIfInOctetsEx | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.1 | Counter32 | read-only | The total number of octets received on the interface, including framing characters. |
| C32 ecpNetIfInUcastPkts | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.2 | Counter32 | read-only | The number of subnetwork-unicast packets delivered to a higher-layer protocol. |
| C32 ecpNetIfInNUcastPkts | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.3 | Counter32 | read-only | The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol. |
| C32 ecpNetIfInDiscards | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.4 | Counter32 | read-only | The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. |
| C32 ecpNetIfInErrors | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.5 | Counter32 | read-only | The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. |
| C32 ecpNetIfInUnknownProtos | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.6 | Counter32 | read-only | The number of packets received via the interface which were discarded because of an unknown or unsupported protocol. |
| C32 ecpNetIfOutOctets | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.7 | Counter32 | read-only | The total number of octets transmitted out of the interface, including framing characters. |
| C32 ecpNetIfOutUcastPkts | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.8 | Counter32 | read-only | The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent. |
| C32 ecpNetIfOutNUcastPkts | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.9 | Counter32 | read-only | The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent. |
| C32 ecpNetIfOutDiscards | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.10 | Counter32 | read-only | The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. |
| C32 ecpNetIfOutErrors | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.11 | Counter32 | read-only | The number of outbound packets that could not be transmitted because of errors. |
| G32 ecpNetIfOutQLen | 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.12 | Gauge32 | read-only | The length of the output packet queue (in packets). |
| ecpIpStatsTable | 1.3.6.1.4.1.326.2.2.1.7.2.2.3 | not-accessible | This table contains the Internet protocol statistics for the Extended Control Processor (ECP) board. | |
| ecpIpStatsEntry | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1 | not-accessible | This entry contains the Internet protocol statistics for the Extended Control Processor (ECP) board. | |
| C32 ecpIpInReceives | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.1 | Counter32 | read-only | The total number of input datagrams received from interfaces, including those received in error. |
| C32 ecpIpInHdrErrors | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.2 | Counter32 | read-only | The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc. |
| C32 ecpIpInAddrErrors | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.3 | Counter32 | read-only | The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address. |
| C32 ecpIpForwDatagrams | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.4 | Counter32 | read-only | The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful. |
| C32 ecpIpInUnknownProtos | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.5 | Counter32 | read-only | The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol. |
| C32 ecpIpInDiscards | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.6 | Counter32 | read-only | The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly. |
| C32 ecpIpInDelivers | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.7 | Counter32 | read-only | The total number of input datagrams successfully delivered to IP user-protocols (including ICMP). |
| C32 ecpIpOutRequests | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.8 | Counter32 | read-only | The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams. |
| C32 ecpIpOutDiscards | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.9 | Counter32 | read-only | The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion. |
| C32 ecpIpOutNoRoutes | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.10 | Counter32 | read-only | The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down. |
| C32 ecpIpReasmReqds | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.11 | Counter32 | read-only | The number of IP fragments received which needed to be reassembled at this entity. |
| C32 ecpIpReasmOKs | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.12 | Counter32 | read-only | The number of IP datagrams successfully re- assembled. |
| C32 ecpIpReasmFails | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.13 | Counter32 | read-only | The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received. |
| C32 ecpIpFragOKs | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.14 | Counter32 | read-only | The number of IP datagrams that have been successfully fragmented at this entity. |
| C32 ecpIpFragFails | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.15 | Counter32 | read-only | The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set. |
| C32 ecpIpFragCreates | 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.16 | Counter32 | read-only | The number of IP datagram fragments that have been generated as a result of fragmentation at this entity. |
| ecpIpRouteTable | 1.3.6.1.4.1.326.2.2.1.7.2.2.4 | not-accessible | This table contains the Internet Protocol routing entries for the Extended Control Processor (ECP) board. | |
| ecpIpRouteEntry | 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1 | not-accessible | This entry contains the Internet Protocol routing data for the Extended Control Processor (ECP) board. | |
| IP ecpIpRouteDest | 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.1 | IpAddress | read-only | The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use. |
| I32 ecpIpRouteIfIndex | 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.2 | Integer32 | read-write | The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| IP ecpIpRouteNextHop | 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.3 | IpAddress | read-write | The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.) |
| I32 ecpIpRouteMetric1 | 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.4 | Integer32 | read-write | The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1. |
| INT ecpIpRouteType | 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.5 | INTEGER | read-write | The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object. |
| IP ecpIpRouteMask | 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.6 | IpAddress | read-write | Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism. |
| ecpIcmpStatsTable | 1.3.6.1.4.1.326.2.2.1.7.2.2.5 | not-accessible | This table contains the Internet Control Message Protocol statistics for the Extended Control Processor (ECP) board. | |
| ecpIcmpStatsEntry | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1 | not-accessible | This entry contains the Internet Control Message Protocol statistics for the Extended Control Processor (ECP) board. | |
| C32 ecpIcmpInMsgs | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.1 | Counter32 | read-only | The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors. |
| C32 ecpIcmpInErrors | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.2 | Counter32 | read-only | The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.). |
| C32 ecpIcmpInDestUnreach | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.3 | Counter32 | read-only | The number of ICMP Destination Unreachable messages received. |
| C32 ecpIcmpInTimeExcds | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.4 | Counter32 | read-only | The number of ICMP Time Exceeded messages received. |
| C32 ecpIcmpInParmProbs | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.5 | Counter32 | read-only | The number of ICMP Parameter Problem messages received. |
| C32 ecpIcmpInSrcQuenchs | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.6 | Counter32 | read-only | The number of ICMP Source Quench messages received. |
| C32 ecpIcmpInRedirects | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.7 | Counter32 | read-only | The number of ICMP Redirect messages received. |
| C32 ecpIcmpInEchos | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.8 | Counter32 | read-only | The number of ICMP Echo (request) messages received. |
| C32 ecpIcmpInEchoReps | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.9 | Counter32 | read-only | The number of ICMP Echo Reply messages received. |
| C32 ecpIcmpInTimestamps | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.10 | Counter32 | read-only | The number of ICMP Timestamp (request) messages received. |
| C32 ecpIcmpInTimestampReps | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.11 | Counter32 | read-only | The number of ICMP Timestamp Reply messages received. |
| C32 ecpIcmpInaddrMasks | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.12 | Counter32 | read-only | The number of ICMP Address Mask Request messages received. |
| C32 ecpIcmpInAddrMaskReps | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.13 | Counter32 | read-only | The number of ICMP Address Mask Reply messages received. |
| C32 ecpIcmpOutMsgs | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.14 | Counter32 | read-only | The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors. |
| C32 ecpIcmpOutErrors | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.15 | Counter32 | read-only | The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value. |
| C32 ecpIcmpOutDestUnreachs | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.16 | Counter32 | read-only | The number of ICMP Destination Unreachable messages sent. |
| C32 ecpIcmpOutTimeExcds | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.17 | Counter32 | read-only | The number of ICMP Time Exceeded messages sent. |
| C32 ecpIcmpOutParmProbs | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.18 | Counter32 | read-only | The number of ICMP Parameter Problem messages sent. |
| C32 ecpIcmpOutSrcQuenchs | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.19 | Counter32 | read-only | The number of ICMP Source Quench messages sent. |
| C32 ecpIcmpOutRedirects | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.20 | Counter32 | read-only | The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects. |
| C32 ecpIcmpOutEchos | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.21 | Counter32 | read-only | The number of ICMP Echo (request) messages sent. |
| C32 ecpIcmpOutEchoReps | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.22 | Counter32 | read-only | The number of ICMP Echo Reply messages sent. |
| C32 ecpIcmpOutTimestamps | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.23 | Counter32 | read-only | The number of ICMP Timestamp (request) messages sent. |
| C32 ecpIcmpOutTimestampReps | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.24 | Counter32 | read-only | The number of ICMP Timestamp Reply messages sent. |
| C32 ecpIcmpOutAddrMasks | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.25 | Counter32 | read-only | The number of ICMP Address Mask Request messages sent. |
| C32 ecpIcmpOutAddrMaskReps | 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.26 | Counter32 | read-only | The number of ICMP Address Mask Reply messages sent. |
| ecpTcpStatsTable | 1.3.6.1.4.1.326.2.2.1.7.2.2.6 | not-accessible | This table contains the Transmission Control Protocol statistics for the Extended Control Processor (ECP) board. | |
| ecpTcpStatsEntry | 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1 | not-accessible | This entry contains the Transmission Control Protocol statistics for the Extended Control Processor (ECP) board. | |
| C32 ecpTcpActiveOpens | 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.1 | Counter32 | read-only | The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state. |
| C32 ecpTcpPassiveOpens | 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.2 | Counter32 | read-only | The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state. |
| C32 ecpTcpAttemptFails | 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.3 | Counter32 | read-only | The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state. |
| C32 ecpTcpEstabResets | 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.4 | Counter32 | read-only | The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state. |
| C32 ecpTcpCurrEstab | 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.5 | Counter32 | read-only | The number of TCP connections for which the current state is either ESTABLISHED or CLOSE- WAIT. |
| C32 ecpTcpInSegs | 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.6 | Counter32 | read-only | The total number of segments received, including those received in error. This count includes segments received on currently established connections. |
| C32 ecpTcpOutSegs | 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.7 | Counter32 | read-only | The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets. |
| C32 ecpTcpRetransSegs | 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.8 | Counter32 | read-only | The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted octets. |
| ecpUdpStatsTable | 1.3.6.1.4.1.326.2.2.1.7.2.2.7 | not-accessible | This table contains the User Datagram Protocol statistics for the Extended Control Processor (ECP) board. | |
| ecpUdpStatsEntry | 1.3.6.1.4.1.326.2.2.1.7.2.2.7.1 | not-accessible | This entry contains the User Datagram Protocol statistics for the Extended Control Processor (ECP) board. | |
| C32 ecpUdpInDatagrams | 1.3.6.1.4.1.326.2.2.1.7.2.2.7.1.1 | Counter32 | read-only | The total number of UDP datagrams delivered to UDP users. |
| C32 ecpUdpNoPorts | 1.3.6.1.4.1.326.2.2.1.7.2.2.7.1.2 | Counter32 | read-only | The total number of received UDP datagrams for which there was no application at the destination port. |
| C32 ecpUdpInErrors | 1.3.6.1.4.1.326.2.2.1.7.2.2.7.1.3 | Counter32 | read-only | The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port. |
| C32 ecpUdpOutDatagrams | 1.3.6.1.4.1.326.2.2.1.7.2.2.7.1.4 | Counter32 | read-only | The total number of UDP datagrams sent from this entity. |
| ecpIpConfigTable | 1.3.6.1.4.1.326.2.2.1.7.2.2.8 | not-accessible | IP Configuration table for the TCMs | |
| ecpIpConfigEntry | 1.3.6.1.4.1.326.2.2.1.7.2.2.8.1 | not-accessible | IP Configuration table entry for the TCMs | |
| INT ecpIpForwarding | 1.3.6.1.4.1.326.2.2.1.7.2.2.8.1.1 | INTEGER | read-write | The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value. |
| ecpSnmp | 1.3.6.1.4.1.326.2.2.1.7.2.3 | |||
| ecpTrapConfGroup | 1.3.6.1.4.1.326.2.2.1.7.2.3.1 | |||
| I32 ecpTrapNumberOfDest | 1.3.6.1.4.1.326.2.2.1.7.2.3.1.1 | Integer32 | read-only | The current number of configured trap destinations. All traps are sent to all destinations. |
| ecpTrapDestTable | 1.3.6.1.4.1.326.2.2.1.7.2.3.1.2 | not-accessible | A table of destinations to which the agent sends traps. | |
| ecpTrapDestEntry | 1.3.6.1.4.1.326.2.2.1.7.2.3.1.2.1 | not-accessible | A table entry containing address of a management station, to which the agent sends traps. | |
| IP ecpTrapDest | 1.3.6.1.4.1.326.2.2.1.7.2.3.1.2.1.1 | IpAddress | read-only | Address to which the agent sends traps. Usually a network management station sets this address to itself. |
| ENT ecpTrapDestStatus | 1.3.6.1.4.1.326.2.2.1.7.2.3.1.2.1.2 | EntryStatus | read-write | The status of this trap destination entry. |
| esiCard | 1.3.6.1.4.1.326.2.2.1.8 | |||
| esiHardware | 1.3.6.1.4.1.326.2.2.1.8.1 | |||
| esiCardHwTable | 1.3.6.1.4.1.326.2.2.1.8.1.1 | not-accessible | This table contains the hardware information for the External Synchronization Interface (ESI) cards. | |
| esiCardHwEntry | 1.3.6.1.4.1.326.2.2.1.8.1.1.1 | not-accessible | This table entry contains the hardware information for a single External Synchronization Interface (ESI) card. | |
| INT esiCardIndex | 1.3.6.1.4.1.326.2.2.1.8.1.1.1.1 | INTEGER | read-only | This is the index for this External Synchronization Interface (ESI) card. |
| INT esiHwCardType | 1.3.6.1.4.1.326.2.2.1.8.1.1.1.2 | INTEGER | read-only | This is the card type for this External Synchronization Interface (ESI) card. |
| I32 esiHwCardVersion | 1.3.6.1.4.1.326.2.2.1.8.1.1.1.3 | Integer32 | read-only | This is the card version for this External Synchronization Interface (ESI) card. |
| INT esiHwPllStatus | 1.3.6.1.4.1.326.2.2.1.8.1.1.1.4 | INTEGER | read-only | This is the card phase-locked loop (PLL) status for this External Synchronization Interface (ESI) card. |
| esiSoftware | 1.3.6.1.4.1.326.2.2.1.8.2 | |||
| esiCardSwTable | 1.3.6.1.4.1.326.2.2.1.8.2.1 | not-accessible | This table contains the software information for the External Synchronization Interface (ESI) cards. | |
| esiCardSwEntry | 1.3.6.1.4.1.326.2.2.1.8.2.1.1 | not-accessible | This table entry contains the software information for a single External Synchronization Interface (ESI) card. | |
| INT esiOperationStatus | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.1 | INTEGER | read-only | This is the operation status of the clock output for this External Synchronization Interface (ESI) card. |
| INT esiCurrentTimingRef | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.2 | INTEGER | read-only | This is the current timing reference in use for this External Synchronization Interface (ESI) card. |
| INT esiRequestedTimingRef | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.3 | INTEGER | read-write | This is the timing reference requested to be used for this External Synchronization Interface (ESI) card. |
| ESI esiPrimaryRefSource | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.4 | EsiReferenceSource | read-write | This is the primary timing reference source for this External Synchronization Interface (ESI) card. |
| ESI esiSecondaryRefSource | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.5 | EsiReferenceSource | read-write | This is the secondary timing reference source for this External Synchronization Interface (ESI) card. |
| I32 esiCurrentFaultBits | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.6 | Integer32 | read-only | This is the current state of the fault bits presented by this External Synchronization Interface (ESI) card. |
| INT esiBitsFramingFormat | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.7 | INTEGER | read-write | This is the framing format of the BITS interface for this External Synchronization Interface (ESI) card. |
| INT esiBitsCodingFormat | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.8 | INTEGER | read-write | This is the coding format of the BITS interface for this External Synchronization Interface (ESI) card. |
| INT esiBitsOutputLevel | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.9 | INTEGER | read-write | This is the output level (dB) of the DS1 BITS interface for this External Synchronization Interface (ESI) card. |
| INT esiRevertiveSwitching | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.10 | INTEGER | read-write | This is the status of the revertive switching for timing sources on this External Synchronization Interface (ESI) card. |
| NUM esiRevertiveDelay | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.11 | TimeInterval | read-write | This is the amount of time after the restoration of the primary timing reference before the External Synchronization Interface (ESI) card will be instructed to return to the primary timing reference. This value is truncated to whole seconds. |
| NUM esiSwitchingDelay | 1.3.6.1.4.1.326.2.2.1.8.2.1.1.12 | TimeInterval | read-write | This is the amount of time after the failure of a timing reference before the External Synchronization Interface (ESI) card will be instructed to switch to the next available timing reference. This value is truncated to whole seconds. |
| esiReferenceTable | 1.3.6.1.4.1.326.2.2.1.8.2.2 | not-accessible | This table contains the timing reference source information for the External Synchronization Interface (ESI) card. | |
| esiReferenceEntry | 1.3.6.1.4.1.326.2.2.1.8.2.2.1 | not-accessible | This table entry contains the timing reference source information for a single External Synchronization Interface (ESI) card. | |
| ESI esiRefSource | 1.3.6.1.4.1.326.2.2.1.8.2.2.1.1 | EsiReferenceSource | read-only | This is the timing reference source index for the External Synchronization Interface (ESI) card. |
| STR esiRefSourceText | 1.3.6.1.4.1.326.2.2.1.8.2.2.1.2 | DisplayString | read-only | This is a textual description of the timing reference source that is provided to the External Synchronization Interface (ESI) card. |
| INT esiRefSourceStatus | 1.3.6.1.4.1.326.2.2.1.8.2.2.1.3 | INTEGER | read-only | This is the status of the timing reference source that is provided to the External Synchornization Interface (ESI) card. |
| INT esiRefSourceAdminStatus | 1.3.6.1.4.1.326.2.2.1.8.2.2.1.4 | INTEGER | read-write | This is the admin status of the timing reference source that is provided to the External Synchornization Interface (ESI) card. |
| INT esiRefSourceQualStatus | 1.3.6.1.4.1.326.2.2.1.8.2.2.1.5 | INTEGER | read-write | This is the RefQual status of the timing reference source that is provided to the External Synchornization Interface (ESI) card. |
RFC description
Manages Timing Control Module for Fore Systems ATM switches including ESI and ECP subsystems.
Start monitoring Fore Systems (later Marconi) ForeRunner ATM switch (ECP Timing Control Module hardware) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.