AcAtm

All MIBs › AcAtm

Organization: AudioCodes Ltd

Last Updated: 2006-03-21

Category: ATM, Vendor: AudioCodes

Description: Provides ATM interface management objects used as shared definitions across AudioCodes ATM-capable gateway and media conversion products.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AcAtm?

AcAtm is an AudioCodes proprietary MIB configuring ATM ports on AudioCodes media gateway hardware that includes ATM interfaces. It exposes a global default application-type and transmission-mode setting alongside a per-port table reporting administrative and operational state, port addressing, and alarm status. As a hardware/configuration-status MIB it lets an administrator confirm an ATM port is administratively and operationally up and check its alarm status when diagnosing a voice-over-ATM transport issue. It is deployed on AudioCodes gateways using ATM as a voice/data transport layer. Engineers can download the AcAtm file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in AcAtm. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

AudioCodes media gateways with ATM transport interfaces

Monitoring Examples

An administrator compares atmPortAdministrativeState against atmPortOperationalState and atmPortAlarmStatus for a port to distinguish an intentionally-disabled port from one that's enabled but alarming.

What Can Be Monitored

ATM port admin/operational state
port alarm status

Imported Objects

From ATM-TC-MIB

AtmAddr

From RFC1155-SMI

IpAddress

From SNMPv2-SMI

MODULE-IDENTITY
OBJECT-TYPE
enterprises

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TAddress
TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
aal2PVC	1.3.6.1.4.1.5003.9.10.6.1.4
INT aal2PVCAction	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.2	INTEGER	read-only	Development Pending - for future use
INT aal2PVCActionResult	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.3	INTEGER	read-only	Development Pending - for future use
aal2PVCEntry	1.3.6.1.4.1.5003.9.10.6.1.4.1.1		not-accessible
INT aal2PVCMaxNumOfCid	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.9	INTEGER	read-write	This is the maximum number of CIDs for the AAL2 PVC.
INT aal2PVCMBS	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.14	INTEGER	read-write	This is the Maximum Burst Size (MBS) for the provisioned virtual channel (PVC).
INT aal2PVCNumOfCidInUse	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.10	INTEGER	read-only	This is the number of CIDs for AAL2 PVC currently in use.
INT aal2PVCPCR	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.12	INTEGER	read-write	This is the peak cell rate (PCR) associated with the provisioned virtual channel (PVC). Includes bandwidth for all CIDs within the PVC
INT aal2PVCPortNumber	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.6	INTEGER	read-write	This is the port number associated with the PVC
INT aal2PVCRemoteGatewayIndex	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.4	INTEGER	read-write	This is the gw index that associated with the remote Gateway table to which this PVC connects (20 octets in length - 40 hexadecimal characters)
ROW aal2PVCRowStatus	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.1	RowStatus	read-create	The RowStatus textual convention is used to manage the creation and deletion and active of conceptual rows.
INT aal2PVCSCR	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.13	INTEGER	read-write	This is the sustained cell rate (SCR) associated with the provisioned virtual channel (PVC). Includes bandwidth for all CIDs within the PVC.
INT aal2PVCServiceCategory	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.11	INTEGER	read-write	This is the Service Category which is either CBR (Constant Bit Rate) or rtVBR (realtime Variable Bit Rate)
aal2PVCTable	1.3.6.1.4.1.5003.9.10.6.1.4.1		not-accessible	This table contains information referring to Permanent Virtual Channels connecting the AMS to the ATM Edge Switch.
INT aal2PVCVCCIPATHID	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.5	INTEGER	read-write	This is the range of Virtual Connection Channel Identifiers which is an end to end identifier for an AAL2 VC.
INT aal2PVCVci	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.8	INTEGER	read-write	This is the VCI assigned to the PVC
INT aal2PVCVpi	1.3.6.1.4.1.5003.9.10.6.1.4.1.1.7	INTEGER	read-write	This is the VPI assigned to the PVC
acAtm	1.3.6.1.4.1.5003.9.10.6			The Audiocodes ATMMIB.
acAtmConfiguration	1.3.6.1.4.1.5003.9.10.6.1
acAtmStatus	1.3.6.1.4.1.5003.9.10.6.2
acBoardMibs	1.3.6.1.4.1.5003.9.10
acGeneric	1.3.6.1.4.1.5003.8
acProducts	1.3.6.1.4.1.5003.9
acRegistrations	1.3.6.1.4.1.5003.7
atmGeneralParams	1.3.6.1.4.1.5003.9.10.6.1.1
INT atmGeneralParamsAtmDefaultApplicationType	1.3.6.1.4.1.5003.9.10.6.1.1.1	INTEGER	read-write	This is the default application type used when the board cannot determine from the H248 add message which AAL type to use.
INT atmGeneralParamsAtmTransmissionMode	1.3.6.1.4.1.5003.9.10.6.1.1.2	INTEGER	read-write	This is the ATM Port Optical Carrier type which indicates whether the European standard (SDH) is to be employed or the North American Standard (SONET)
atmPort	1.3.6.1.4.1.5003.9.10.6.1.2
INT atmPortAddressMode	1.3.6.1.4.1.5003.9.10.6.1.2.1.1.7	INTEGER	read-only	The mode reflects the type of address in operation. addrModeNone(0) : No administrative address has been configured and no ILMI address has been registered. Thus no address is available to assign to the port. addrModeManual(1): An Administrative address has been configured and no ILMI address has been registered. Thus the port is assigned the manually configured address.addrModeILMI (2): An ILMI address has been registered. The port is assigned this address. The administrative address is ignored if it has been configured.
ATM atmPortAdminAddress	1.3.6.1.4.1.5003.9.10.6.1.2.1.1.4	AtmAddr	read-write	This is the Administrative�ATM Port Address (20 octets in length - 40 hexadecimal characters). This address is manually configured.�This address is used when ILMI is not available.
INT atmPortAdministrativeState	1.3.6.1.4.1.5003.9.10.6.1.2.1.1.1	INTEGER	read-write	This is the ATM Port Administrative State
INT atmPortAlarmStatus	1.3.6.1.4.1.5003.9.10.6.1.2.1.1.6	INTEGER	read-only	This is the ATM Port Alarm Status. The possible values are: cleared(0) - LOS, AIS and RDI conditions are not present los(1) - the LOS condition is present ais(2) - AIS condition is present (LOS condition is not present) rdi(4) - RDI condition is present (LOS and AIS conditions are not present) Note: Alarm conditions (from the SONET/SDH standard documents) are: LOS - Loss Of Signal AIS - Alarm Indication Signal RDI - Remote Defect Indication
atmPortEntry	1.3.6.1.4.1.5003.9.10.6.1.2.1.1		not-accessible
atmPortLoopbackConfig	1.3.6.1.4.1.5003.9.10.6.1.5
INT atmPortLoopbackConfigAction	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.2	INTEGER	read-only	Development Pending - for future use
INT atmPortLoopbackConfigActionResult	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.3	INTEGER	read-only	Development Pending - for future use
atmPortLoopbackConfigEntry	1.3.6.1.4.1.5003.9.10.6.1.5.1.1		not-accessible
INT atmPortLoopbackConfigInBoundVirtualPath	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.7	INTEGER	read-write	If the atmLoopback mode is VP, this specifies the VP identity for the cells coming from the ATM edge switch
INT atmPortLoopbackConfigIsUsed	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.1	INTEGER	read-write	This tells whether or not the port loopback is used. If the port is available on the board, this is yes.
INT atmPortLoopbackConfigMBS	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.13	INTEGER	read-write	This is the Maximum Burst Size (MBS) associated with the switched virtual channel (SVC). This is used in realtime Variable Bit Rate (rtVBR) traffice. The unit for this parameter is ATM cells.
INT atmPortLoopbackConfigMode	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.5	INTEGER	read-write	This is the mode in which the loopback will work: no loopback, UNI loopback, or Virtual Path loopback
INT atmPortLoopbackConfigOutBoundVirtualPath	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.6	INTEGER	read-write	If the atmLoopback mode is VP, this specifies the VP identity for the cells going toward the ATM edge switch
INT atmPortLoopbackConfigPCR	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.11	INTEGER	read-write	This is the peak cell rate (PCR) associated with the switched virtual channel (SVC). This is used for Constant Bit Rate (CBR) traffic. For AAL2, this includes bandwidth for all CIDs within the SVC. For AAL1, there is only one channel per SVC (and no concept of a CID).
INT atmPortLoopbackConfigPortNumber	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.4	INTEGER	read-write	The port number associated with the optical port which is being described.
INT atmPortLoopbackConfigSCR	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.12	INTEGER	read-write	This is the sustained cell rate (SCR) associated with the switched virtual channel (SVC). This is used for realtime Variable Bit Rate (rtVBR) traffice. For AAL2, this includes bandwidth for all CIDs within the SVC. For AAL1, there is only one channel per SVC (and no concept of a CID).
INT atmPortLoopbackConfigServiceCategory	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.10	INTEGER	read-write	This category is limited to Constant Bit Rate (CBR) traffic or realtime Variable Bit Rate (rtVBR) for this release.
atmPortLoopbackConfigTable	1.3.6.1.4.1.5003.9.10.6.1.5.1		not-accessible	This table gives the Loopback Configuration associated with a given Optical Fiber Port number.
INT atmPortLoopbackConfigVciRangeFirst	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.8	INTEGER	read-write	If the atmLoopback mode is VP, this specifies the minimum VCI within the inbound and outbound VP which may be used.
INT atmPortLoopbackConfigVciRangeLast	1.3.6.1.4.1.5003.9.10.6.1.5.1.1.9	INTEGER	read-write	If the atmLoopback mode is VP, this specifies the maximum VCI within the inbound and outbound VP which may be used.
INT atmPortNumber	1.3.6.1.4.1.5003.9.10.6.1.2.1.1.3	INTEGER	read-only	This is the ATM Port Number
ATM atmPortOperationalAddress	1.3.6.1.4.1.5003.9.10.6.1.2.1.1.5	AtmAddr	read-only	This is the port ATM address currently in operation (i.e.:assigned to this port). This address�is set to atmPortAdminAddress if no ILMI address is registered. If an ILMI address is successfully registered, then atmPortOperationalAddress will be set to the ILMI one, though an administrative address may have already been configured. Thus ILMI address always takes precedence over the administrative one. If both the administrative and ILMI addresses are unavailable then the operational address is left empty. Refer to atmPortAddressMode for which address is operational.
INT atmPortOperationalState	1.3.6.1.4.1.5003.9.10.6.1.2.1.1.2	INTEGER	read-only	This is the Port Operational State
atmPortTable	1.3.6.1.4.1.5003.9.10.6.1.2.1		not-accessible	This table indicates general information about and alarm status of the ATM optical fiber ports. It is also used to configure the ATM address associated with the optical port and read that address.
atmRemoteGateway	1.3.6.1.4.1.5003.9.10.6.1.3
INT atmRemoteGatewayAction	1.3.6.1.4.1.5003.9.10.6.1.3.1.1.2	INTEGER	read-only	Development Pending -for future use
INT atmRemoteGatewayActionResult	1.3.6.1.4.1.5003.9.10.6.1.3.1.1.3	INTEGER	read-only	Development Pending -future use
INT atmRemoteGatewayALCAPInstanceNum	1.3.6.1.4.1.5003.9.10.6.1.3.1.1.7	INTEGER	read-write	ALCAP Instance number associated with the remote Gateway ( 3G only)
atmRemoteGatewayEntry	1.3.6.1.4.1.5003.9.10.6.1.3.1.1		not-accessible
INT atmRemoteGatewayIndex	1.3.6.1.4.1.5003.9.10.6.1.3.1.1.4	INTEGER	read-write	.
OCT atmRemoteGatewayName	1.3.6.1.4.1.5003.9.10.6.1.3.1.1.5	OCTET STRING	read-write	Remote Gateway name
ATM atmRemoteGatewayNSAPAddress	1.3.6.1.4.1.5003.9.10.6.1.3.1.1.6	AtmAddr	read-write	This is the ATM Address associated with the remote Gateway to which this PVC connects (20 octets in length - 40 hexadecimal characters)
ROW atmRemoteGatewayRowStatus	1.3.6.1.4.1.5003.9.10.6.1.3.1.1.1	RowStatus	read-create	The RowStatus textual convention is used to manage the creation and deletion and active of conceptual rows.
atmRemoteGatewayTable	1.3.6.1.4.1.5003.9.10.6.1.3.1		not-accessible	This includes the destination remote Gateways (and RNC) that the Media Gateway would have signaling contact with.
atmSvcConnection	1.3.6.1.4.1.5003.9.10.6.2.1
INT atmSvcConnectionAALType	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.6	INTEGER	read-only	This is the Adaptation Layer type. It is either AAL1 or AAL2.
INT atmSvcConnectionDirection	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.7	INTEGER	read-only	This is the direction in which the SVC was setup. Incoming means the this end received the SETUP. Outgoing means this end sent the SETUP.
U32 atmSvcConnectionEecid	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.8	Unsigned32	read-only	This is the unique end to end identifier associated with the setup of AAL1 SVCs
atmSvcConnectionEntry	1.3.6.1.4.1.5003.9.10.6.2.1.1.1		not-accessible
INT atmSvcConnectionIndex	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.1	INTEGER	read-only	A unique index, that identifies the SVC on the system.
INT atmSvcConnectionMaxNumOfCid	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.10	INTEGER	read-only	This is the maximum number of CIDs for an AAL2 SVC.
INT atmSvcConnectionNumOfCidInUse	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.11	INTEGER	read-only	This is the number of channel Ids currently in use in a given SVC.
INT atmSvcConnectionPort	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.3	INTEGER	read-only	This is the port on which the SVC is connected
ATM atmSvcConnectionRemoteGatewayAddress	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.2	AtmAddr	read-only	This is the ATM Address associated with the remote Gateway to which this SVC connects (20 octets in length - 40 hexadecimal characters)
atmSvcConnectionTable	1.3.6.1.4.1.5003.9.10.6.2.1.1		not-accessible	This is the table which describes the read only characteristics of a given AAL1 or AAL2 SVC.
INT atmSvcConnectionVcci	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.9	INTEGER	read-only	This is the unique identity of an SVC associated with an AAL2 connection
INT atmSvcConnectionVci	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.5	INTEGER	read-only	This is the VCI associated with the SVC
INT atmSvcConnectionVpi	1.3.6.1.4.1.5003.9.10.6.2.1.1.1.4	INTEGER	read-only	This is the VPI associated with the SVC
atmSvcProfile	1.3.6.1.4.1.5003.9.10.6.1.6
atmSvcProfileEntry	1.3.6.1.4.1.5003.9.10.6.1.6.1.1		not-accessible
INT atmSvcProfileIndex	1.3.6.1.4.1.5003.9.10.6.1.6.1.1.2	INTEGER	read-write	Initially only one SVC Profile is supported. This parameter may be updated later as the table supports more profiles
INT atmSvcProfileIsUsed	1.3.6.1.4.1.5003.9.10.6.1.6.1.1.1	INTEGER	read-write	This tells whether or not this SVC profile is used. If it is used, the value is yes.
INT atmSvcProfileMaxNumOfCids	1.3.6.1.4.1.5003.9.10.6.1.6.1.1.3	INTEGER	read-write	The CIDs fall in the range of 8 to 255, so there are a maximum of 248 CIDs possible. The assignment of CID #8 may be received but not initiated. Assignments from the low end of the CID range should start with 9 as there are some vendors who use 8 for a special OAM purpose.
INT atmSvcProfileMBS	1.3.6.1.4.1.5003.9.10.6.1.6.1.1.6	INTEGER	read-write	This is the Maximum Burst Size (MBS) associated with the switched virtual channel (SVC). This is used in realtime Variable Bit Rate (rtVBR) traffice. The unit for this parameter is ATM cells.
INT atmSvcProfilePCR	1.3.6.1.4.1.5003.9.10.6.1.6.1.1.4	INTEGER	read-write	This is the peak cell rate (PCR) associated with the switched virtual channel (SVC). This is used for Constant Bit Rate (CBR) traffic. For AAL2, this includes bandwidth for all CIDs within the SVC. For AAL1, there is only one channel per SVC (and no concept of a CID).
INT atmSvcProfilePersistence	1.3.6.1.4.1.5003.9.10.6.1.6.1.1.7	INTEGER	read-write	This is the parameter which descirbes how long an AAL2 SVC will persist even when no CIDs are in use. Generally, this is on the order of 180 to 600 seconds. Non-persistent SVCs should have a value of 0.
INT atmSvcProfileSCR	1.3.6.1.4.1.5003.9.10.6.1.6.1.1.5	INTEGER	read-write	This is the sustained cell rate (SCR) associated with the switched virtual channel (SVC). This is used for realtime Variable Bit Rate (rtVBR) traffice. For AAL2, this includes bandwidth for all CIDs within the SVC. For AAL1, there is only one channel per SVC (and no concept of a CID).
INT atmSvcProfileServiceCategory	1.3.6.1.4.1.5003.9.10.6.1.6.1.1.8	INTEGER	read-write	This category is limited to Constant Bit Rate (CBR) traffic or realtime Variable Bit Rate (rtVBR) for this release.
atmSvcProfileTable	1.3.6.1.4.1.5003.9.10.6.1.6.1		not-accessible	This table indicates information about profiles associated with the creation of each new AAL2 SVC.
audioCodes	1.3.6.1.4.1.5003

RFC description

AudioCodes ATM board MIB for managing ATM transmission configuration and remote gateway settings.

Start monitoring AudioCodes media/VoIP gateways with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AcAtm

What Is AcAtm?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description