FSM7326-ROUTING-MIB

All MIBs › FSM7326-ROUTING-MIB

Organization: Netgear

Last Updated: 2003-11-10

Description: FSM7326-ROUTING-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is FSM7326-ROUTING-MIB?

FSM7326-ROUTING-MIB is a vendor MIB associated with the FSM7326 switch platform (an Enterasys/Cabletron-lineage stackable Layer 2/3 switch model), intended to cover routing-related management objects for that specific hardware. No module description or sample objects were captured for this entry, so its precise object set cannot be verified from the available source data. Based on the product name and typical conventions for such platform-specific routing MIBs, it likely exposes IP routing table, interface, and protocol status objects relevant to Layer 3 switching on the FSM7326. Any dependency on companion FSM7326 MIBs or standard routing MIBs (e.g. the IETF IP-MIB) is plausible but not confirmed by the available data. It would be deployed on FSM7326 switch hardware in environments requiring Layer 3 routing alongside Layer 2 switching. Engineers can download the FSM7326-ROUTING-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in FSM7326-ROUTING-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Netgear FSM7326 managed switch (Layer 3 routing: OSPF/RIP) — Identified via the ORGANIZATION field ('Netgear') and cross-reference against sibling FSM7326-REF-MIB (enterprise OID 4526, Netgear) and other FSM7326-* modules, not 'Enterasys/Cabletron-lineage' as previously described.

Monitoring Examples

No sample objects or module description were available for this entry, so no specific monitoring scenario can be honestly constructed; a general routing-MIB use case would involve polling IP routing table and interface status objects, but no concrete table names can be cited without inventing them.

Imported Objects

From FSM7326-REF-MIB

fsm7326

MODULE-IDENTITY

From OSPF-MIB

ospfAreaEntry	OBJECT-TYPE
ospfIfEntry
ospfVirtIfEntry

From RFC1155-SMI

TimeTicks

From RFC1213-MIB

DisplayString
PhysAddress

From RIPv2-MIB

rip2IfConfEntry

OBJECT-TYPE

From SNMPv2-SMI

Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using agentSwitchArpTotalEntryCountCurrent OID:

Select a Netgear FSM7326 managed switch (Layer 3 routing: OSPF/RIP) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type agentSwitchArpTotalEntryCountCurrent into the Find box to locate it in the OID tree, then select it and click OK. It reports the current number of entries in the ARP cache. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Gauge32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
fsm7326Routing	1.3.6.1.4.1.4526.1.9.2
agentSwitchArpGroup	1.3.6.1.4.1.4526.1.9.2.1
I32 agentSwitchArpAgeoutTime	1.3.6.1.4.1.4526.1.9.2.1.1	Integer32	read-write	Configures the ARP entry ageout time in seconds. Allowable range: 15-21600
I32 agentSwitchArpResponseTime	1.3.6.1.4.1.4526.1.9.2.1.2	Integer32	read-write	Configures the ARP request response timeout in seconds. Allowable range: 1-10
I32 agentSwitchArpMaxRetries	1.3.6.1.4.1.4526.1.9.2.1.3	Integer32	read-write	Configures the ARP count of maximum request for retries. Allowable range: 0-10
I32 agentSwitchArpCacheSize	1.3.6.1.4.1.4526.1.9.2.1.4	Integer32	read-write	Configures the ARP maximum number of entries in the cache. Allowable range is platform-specific.
INT agentSwitchArpDynamicRenew	1.3.6.1.4.1.4526.1.9.2.1.5	INTEGER	read-write	This indicates the current setting of ARP dynamic renew mode.
G32 agentSwitchArpTotalEntryCountCurrentEx	1.3.6.1.4.1.4526.1.9.2.1.6	Gauge32	read-only	Current number of entries in the ARP cache.
G32 agentSwitchArpTotalEntryCountPeak	1.3.6.1.4.1.4526.1.9.2.1.7	Gauge32	read-only	Peak number of entries recorded in the ARP cache over time. This value is restarted whenever the ARP cache size is changed.
G32 agentSwitchArpStaticEntryCountCurrent	1.3.6.1.4.1.4526.1.9.2.1.8	Gauge32	read-only	Current number of configured static ARP entries.
I32 agentSwitchArpStaticEntryCountMax	1.3.6.1.4.1.4526.1.9.2.1.9	Integer32	read-only	Maximum number of configurable static ARP entries.
agentSwitchArpTable	1.3.6.1.4.1.4526.1.9.2.1.10		not-accessible	This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information.
agentSwitchArpEntry	1.3.6.1.4.1.4526.1.9.2.1.10.1		not-accessible
TIK agentSwitchArpAge	1.3.6.1.4.1.4526.1.9.2.1.10.1.1	TimeTicks	read-only	This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.
IP agentSwitchArpIpAddress	1.3.6.1.4.1.4526.1.9.2.1.10.1.2	IpAddress	read-only	The IP Address assigned to each interface.
PHY agentSwitchArpMacAddress	1.3.6.1.4.1.4526.1.9.2.1.10.1.3	PhysAddress	read-create	The hardware MAX Address that each interface maps to.
I32 agentSwitchArpInterface	1.3.6.1.4.1.4526.1.9.2.1.10.1.4	Integer32	read-only	The Associated IfIndex which identified the ARP Entry.
INT agentSwitchArpType	1.3.6.1.4.1.4526.1.9.2.1.10.1.5	INTEGER	read-only	The type of ARP entry.
ROW agentSwitchArpStatus	1.3.6.1.4.1.4526.1.9.2.1.10.1.6	RowStatus	read-write	The status of this ARP entry. Setting this object destroy will remove the entry.
agentSwitchIpGroup	1.3.6.1.4.1.4526.1.9.2.2
INT agentSwitchIpRoutingMode	1.3.6.1.4.1.4526.1.9.2.2.1	INTEGER	read-write	Administratively enables/disables routing on the switch.
agentSwitchIpInterfaceTable	1.3.6.1.4.1.4526.1.9.2.2.3		not-accessible
agentSwitchIpInterfaceEntry	1.3.6.1.4.1.4526.1.9.2.2.3.1		not-accessible
I32 agentSwitchIpInterfaceIfIndex	1.3.6.1.4.1.4526.1.9.2.2.3.1.1	Integer32	read-only	The IfIndex associated with this instance.
IP agentSwitchIpInterfaceIpAddress	1.3.6.1.4.1.4526.1.9.2.2.3.1.2	IpAddress	read-write	The IpAddress assigned to this interface. When setting this value, the value of agentSwitchIpInterfaceNetMask must be set at the same time.
IP agentSwitchIpInterfaceNetMask	1.3.6.1.4.1.4526.1.9.2.2.3.1.3	IpAddress	read-write	The NetMask assigned to this interface. When setting this value, the value of agentSwitchIpInterfaceIpAddress must be set at the same time.
INT agentSwitchIpInterfaceClearIp	1.3.6.1.4.1.4526.1.9.2.2.3.1.4	INTEGER	read-write	Sets the interfaces IpAddress and NetMask back to 0.0.0.0
INT agentSwitchIpInterfaceRoutingMode	1.3.6.1.4.1.4526.1.9.2.2.3.1.5	INTEGER	read-write	Enables or disables routing for this interface.
agentSwitchIpRouterDiscoveryTable	1.3.6.1.4.1.4526.1.9.2.2.4		not-accessible	There is no global administrative flag for router discovery. The global routing flag (agentSwitchIpRoutingMode) will be used for this purpose. If routing is disabled, router discovery is disabled as well.
agentSwitchIpRouterDiscoveryEntry	1.3.6.1.4.1.4526.1.9.2.2.4.1		not-accessible
I32 agentSwitchIpRouterDiscoveryIfIndex	1.3.6.1.4.1.4526.1.9.2.2.4.1.1	Integer32	read-only	Interface Number to configure Router Discovery on.
INT agentSwitchIpRouterDiscoveryAdvertiseMode	1.3.6.1.4.1.4526.1.9.2.2.4.1.2	INTEGER	read-write	Enable or disable router discovery on the interface.
I32 agentSwitchIpRouterDiscoveryMaxAdvertisementInterval	1.3.6.1.4.1.4526.1.9.2.2.4.1.3	Integer32	read-write	Maximum time allowed between sending router advertisements from the interface.
I32 agentSwitchIpRouterDiscoveryMinAdvertisementInterval	1.3.6.1.4.1.4526.1.9.2.2.4.1.4	Integer32	read-write	Minimum time allowed between sending router advertisements from the interface. This value must be less than or equal to agentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
I32 agentSwitchIpRouterDiscoveryAdvertisementLifetime	1.3.6.1.4.1.4526.1.9.2.2.4.1.5	Integer32	read-write	Value of lifetime field of router advertsisement sent from the interface. This value must be greater than or equal to agentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
I32 agentSwitchIpRouterDiscoveryPreferenceLevel	1.3.6.1.4.1.4526.1.9.2.2.4.1.6	Integer32	read-write	Preferability of the address as a default router address, related to other addresses on the same subnet. This is defined as the larger the number, the higher the preference.
IP agentSwitchIpRouterDiscoveryAdvertisementAddress	1.3.6.1.4.1.4526.1.9.2.2.4.1.7	IpAddress	read-write	Address used when sending router advertisements from the interface.
agentSwitchIpVlanTable	1.3.6.1.4.1.4526.1.9.2.2.5		not-accessible
agentSwitchIpVlanEntry	1.3.6.1.4.1.4526.1.9.2.2.5.1		not-accessible	A Static VLAN for which routing can be enabled/disabled
I32 agentSwitchIpVlanId	1.3.6.1.4.1.4526.1.9.2.2.5.1.1	Integer32	read-only	The Vlan's Id.
I32 agentSwitchIpVlanIfIndex	1.3.6.1.4.1.4526.1.9.2.2.5.1.2	Integer32	read-only	The IfIndex associated with this VLAN.
ROW agentSwitchIpVlanRoutingStatus	1.3.6.1.4.1.4526.1.9.2.2.5.1.3	RowStatus	read-create	Status of Routing mode per Vlan. active(1) - Vlan is enabled for routing createAndGo(4) - Adds Vlan entry for routing destroy(6) - Removes Vlan from routing
agentRouterRipConfigGroup	1.3.6.1.4.1.4526.1.9.2.3
INT agentRouterRipAdminState	1.3.6.1.4.1.4526.1.9.2.3.1	INTEGER	read-write	Sets the administrative mode of RIP in the router.
INT agentRouterRipSplitHorizonMode	1.3.6.1.4.1.4526.1.9.2.3.2	INTEGER	read-write	Sets the RIP split horizon operating mode in the router. A value of none(1) means split horizon processing is disabled. When set to simple(2), the simple split horizon technique is used. When set to poisonReverse(3), the split horizon with poison reverse technique is used. The default split horizon mode is simple(2).
INT agentRouterRipAutoSummaryMode	1.3.6.1.4.1.4526.1.9.2.3.3	INTEGER	read-write	Sets the RIP auto summarization mode in the router. A value of enable(1) means that routes advertized by this RIP router are combined, or summarized, whenever possible into aggregates. When set to disable(2), routes are not aggregated in RIP updates generated by this router. The default auto summary mode is enable(1).
INT agentRouterRipHostRoutesAcceptMode	1.3.6.1.4.1.4526.1.9.2.3.4	INTEGER	read-write	Sets the RIP host route acceptance mode in the router. A value of enable(1) means that host routes advertized to this RIP router will be accepted (learned) into its routing table. When set to disable(2), host routes advertized in RIP updates from neighboring routers are ignored. The default host routes accept mode is enable(1).
I32 agentRouterRipDefaultMetric	1.3.6.1.4.1.4526.1.9.2.3.5	Integer32	read-write	Default metric of redistributed routes, when RIP redistributes from other protocols.
T/F agentRouterRipDefaultMetricConfigured	1.3.6.1.4.1.4526.1.9.2.3.6	TruthValue	read-write	Flag to determine whether RIP default-metric is configured or not.
T/F agentRouterRipDefaultInfoOriginate	1.3.6.1.4.1.4526.1.9.2.3.7	TruthValue	read-write	Flag to determine, whether RIP can advertise a default-route learned from another protocol.
agentRipRouteRedistTable	1.3.6.1.4.1.4526.1.9.2.3.8		not-accessible	This table contains the MIB objects required to configure route-redistribution for RIP. Here, RIP is the Destination protocol and the source protocols can be any of : BGP, OSPF, Static, Connected.
agentRipRouteRedistEntry	1.3.6.1.4.1.4526.1.9.2.3.8.1		not-accessible
INT agentRipRouteRedistSource	1.3.6.1.4.1.4526.1.9.2.3.8.1.1	INTEGER	read-only	Source route, from which RIP can redistribute routes. This object also acts as the identifier for the RIP redistribution Table entry.
INT agentRipRouteRedistMode	1.3.6.1.4.1.4526.1.9.2.3.8.1.2	INTEGER	read-write	User enabels/disables route-redistribution for a particular source protocol.
I32 agentRipRouteRedistMetric	1.3.6.1.4.1.4526.1.9.2.3.8.1.3	Integer32	read-write	Metric used for redistributing a particular source protocol route into RIP.
T/F agentRipRouteRedistMetricConfigured	1.3.6.1.4.1.4526.1.9.2.3.8.1.4	TruthValue	read-write	Flag to determine whether RIP redistribute-metric is configured or not.
INT agentRipRouteRedistMatchInternal	1.3.6.1.4.1.4526.1.9.2.3.8.1.5	INTEGER	read-write	If this flag is true, RIP redistributes OSPF internal routes. It will be non-applicable, when source protocol is other than ospf.
INT agentRipRouteRedistMatchExternal1	1.3.6.1.4.1.4526.1.9.2.3.8.1.6	INTEGER	read-write	If this flag is true, RIP redistributes OSPF External1 routes. It will be non-applicable, when source protocol is other than ospf.
INT agentRipRouteRedistMatchExternal2	1.3.6.1.4.1.4526.1.9.2.3.8.1.7	INTEGER	read-write	If this flag is true, RIP redistributes OSPF External2 routes. It will be non-applicable, when source protocol is other than ospf.
INT agentRipRouteRedistMatchNSSAExternal1	1.3.6.1.4.1.4526.1.9.2.3.8.1.8	INTEGER	read-write	If this flag is true, RIP redistributes OSPF NSSA-External1 routes. It will be non-applicable, when source protocol is other than ospf.
INT agentRipRouteRedistMatchNSSAExternal2	1.3.6.1.4.1.4526.1.9.2.3.8.1.9	INTEGER	read-write	If this flag is true, RIP redistributes OSPF NSSA-External2 routes. It will be non-applicable, when source protocol is other than ospf.
U32 agentRipRouteRedistDistList	1.3.6.1.4.1.4526.1.9.2.3.8.1.10	Unsigned32	read-write	Access-list number of the access-list, which filters routes received from a source-protocol.
T/F agentRipRouteRedistDistListConfigured	1.3.6.1.4.1.4526.1.9.2.3.8.1.11	TruthValue	read-write	Flag to determine whether Access-list is configured or not.
agentRip2IfConfTable	1.3.6.1.4.1.4526.1.9.2.3.9		not-accessible	A list of subnets which require separate configuration in RIP. Augments rip2IfConfTable in the RIPv2-MIB.
agentRip2IfConfEntry	1.3.6.1.4.1.4526.1.9.2.3.9.1		not-accessible	A Single Routing Domain in a single Subnet. Augments rip2IfConfEntry in RIPv2-MIB.
INT agentRip2IfConfAuthKeyId	1.3.6.1.4.1.4526.1.9.2.3.9.1.1	INTEGER	read-create	The identifier for the authentication key used on this interface. This field is only meaningful when the RIPv2-MIB rip2IfConfAuthType is md5(3); otherwise, the value is not used.
agentRouterOspfConfigGroup	1.3.6.1.4.1.4526.1.9.2.4
I32 agentOspfDefaultMetric	1.3.6.1.4.1.4526.1.9.2.4.1	Integer32	read-write	Default metric of redistributed routes, when OSPF redistributes from other protocols.
T/F agentOspfDefaultMetricConfigured	1.3.6.1.4.1.4526.1.9.2.4.2	TruthValue	read-write	Flag to determine whether OSPF default-metric is configured or not.
T/F agentOspfDefaultInfoOriginate	1.3.6.1.4.1.4526.1.9.2.4.3	TruthValue	read-write	Flag to determine, whether OSPF can advertise a default-route learned from another protocol.
T/F agentOspfDefaultInfoOriginateAlways	1.3.6.1.4.1.4526.1.9.2.4.4	TruthValue	read-write	When this flag is true, the router advertises 0.0.0.0/0.0.0.0 always. Without this option, OSPF will only advertise 0.0.0.0/0.0.0.0 if the router's forwarding table contains a default route.
I32 agentOspfDefaultInfoOriginateMetric	1.3.6.1.4.1.4526.1.9.2.4.5	Integer32	read-write	Metric of the default route,which OSPF advertises when learned from other protocol.
T/F agentOspfDefaultInfoOriginateMetricConfigured	1.3.6.1.4.1.4526.1.9.2.4.6	TruthValue	read-write	Flag to determine whether OSPF default-info originate metric is configured or not.
INT agentOspfDefaultInfoOriginateMetricType	1.3.6.1.4.1.4526.1.9.2.4.7	INTEGER	read-write	Metric Type of the default route,which OSPF advertises when learned from other protocol. It can be 1(external type 1) or 2(external type 2).
agentOspfRouteRedistTable	1.3.6.1.4.1.4526.1.9.2.4.8		not-accessible	This table contains the MIB objects required to configure route-redistribution for OSPF. Here, OSPF is the Destination protocol and the source protocols can be any of : BGP, RIP, Static, Connected.
agentOspfRouteRedistEntry	1.3.6.1.4.1.4526.1.9.2.4.8.1		not-accessible
INT agentOspfRouteRedistSource	1.3.6.1.4.1.4526.1.9.2.4.8.1.1	INTEGER	read-only	Source protocol, from which OSPF can redistribute routes. This object also acts as the identifier for the OSPF redistribution Table entry.
INT agentOspfRouteRedistMode	1.3.6.1.4.1.4526.1.9.2.4.8.1.2	INTEGER	read-write	User enabels/disables route-redistribution for a particular source protocol.
I32 agentOspfRouteRedistMetric	1.3.6.1.4.1.4526.1.9.2.4.8.1.3	Integer32	read-write	Metric used for redistributing a particular source protocol route into OSPF.
T/F agentOspfRouteRedistMetricConfigured	1.3.6.1.4.1.4526.1.9.2.4.8.1.4	TruthValue	read-write	Flag to determine whether OSPF redistribute-metric is configured or not.
INT agentOspfRouteRedistMetricType	1.3.6.1.4.1.4526.1.9.2.4.8.1.5	INTEGER	read-write	Metric Type of routes,which OSPF redistributes from other source protocols. It can be 1(external type 1) or 2(external type 2).
U32 agentOspfRouteRedistTag	1.3.6.1.4.1.4526.1.9.2.4.8.1.6	Unsigned32	read-write	It specifies the tag field in routes redistributed by OSPF.
T/F agentOspfRouteRedistSubnets	1.3.6.1.4.1.4526.1.9.2.4.8.1.7	TruthValue	read-write	If this value is false, then OSPF will not redistribute subnetted routes.
U32 agentOspfRouteRedistDistList	1.3.6.1.4.1.4526.1.9.2.4.8.1.8	Unsigned32	read-write	Access-list number of the access-list, which filters routes received from a source-protocol.
T/F agentOspfRouteRedistDistListConfigured	1.3.6.1.4.1.4526.1.9.2.4.8.1.9	TruthValue	read-write	Flag to determine whether Access-list is configured or not.
agentOspfIfTable	1.3.6.1.4.1.4526.1.9.2.4.9		not-accessible	The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF. Augments ospfIfTable from the OSPF-MIB.
agentOspfIfEntry	1.3.6.1.4.1.4526.1.9.2.4.9.1		not-accessible	The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF. Augments ospfIfEntry in OSPF-MIB.
INT agentOspfIfAuthKeyId	1.3.6.1.4.1.4526.1.9.2.4.9.1.1	INTEGER	read-create	The identifier for the authentication key used on this interface. This field is only meaningful when the OSPF-MIB ospfIfAuthType is md5(2); otherwise, the value is not used.
agentOspfVirtIfTable	1.3.6.1.4.1.4526.1.9.2.4.10		not-accessible	Information about this router's virtual inter- faces. Augments ospfVirtIfTable from the OSPF-MIB.
agentOspfVirtIfEntry	1.3.6.1.4.1.4526.1.9.2.4.10.1		not-accessible	Information about a single Virtual Interface. Augments ospfVirtIfEntry in OSPF-MIB.
INT agentOspfVirtIfAuthKeyId	1.3.6.1.4.1.4526.1.9.2.4.10.1.1	INTEGER	read-create	The identifier for the authentication key used on this virtual interface. This field is only meaningful when the OSPF-MIB ospfVirtIfAuthType is md5(2); otherwise, the value is not used.
INT agentRouterOspfRFC1583CompatibilityMode	1.3.6.1.4.1.4526.1.9.2.4.11	INTEGER	read-write	From RFC2328: Controls the preference rules used in Section 16.4 when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583 ([Ref9]). When set to 'disabled', the preference rules are those stated in Section 16.4.1, which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas. Set to 'enabled' by default. In order to minimize the chance of routing loops, all OSPF routers in an OSPF routing domain should have RFC1583Compatibility set identically. When there are routers present that have not been updated with the functionality specified in Section 16.4.1 of this memo, all routers should have RFC1583Compatibility set to 'enabled'. Otherwise, all routers should have RFC1583Compatibility set to 'disabled', preventing all routing loops.
agentOspfAreaTable	1.3.6.1.4.1.4526.1.9.2.4.12		not-accessible	Information describing the additional configured parameters and cumulative statistics of the router's attached areas.
agentOspfAreaEntry	1.3.6.1.4.1.4526.1.9.2.4.12.1		not-accessible	Information describing the additional configured parameters and cumulative statistics of the router's attached areas.
I32 agentOspfAuthType	1.3.6.1.4.1.4526.1.9.2.4.12.1.2	Integer32	read-write	The authentication type specified for an area. Additional authentication types may be assigned locally on a per Area basis.
agentSnmpTrapFlagsConfigGroupLayer3	1.3.6.1.4.1.4526.1.9.2.5
INT agentSnmpVRRPNewMasterTrapFlag	1.3.6.1.4.1.4526.1.9.2.5.1	INTEGER	read-write	This flag enables the sending of VRRP new master notification traps.
INT agentSnmpVRRPAuthFailureTrapFlag	1.3.6.1.4.1.4526.1.9.2.5.2	INTEGER	read-write	This flag enables the sending of VRRP authentication failure notification traps.
agentBootpDhcpRelayGroup	1.3.6.1.4.1.4526.1.9.2.6
I32 agentBootpDhcpRelayMaxHopCount	1.3.6.1.4.1.4526.1.9.2.6.1	Integer32	read-write	The BOOTP/DHCP Max Hop Count. The relay agent silently discards BOOTREQUEST messages whose hops field exceeds the value 16 assuming that the request is looped through the intermediate agents. The default value is 4.
IP agentBootpDhcpRelayForwardingIp	1.3.6.1.4.1.4526.1.9.2.6.2	IpAddress	read-write	The BOOTP/DHCP Server IP Address. All the requests will be forwarded and the replies expected from this address.
INT agentBootpDhcpRelayForwardMode	1.3.6.1.4.1.4526.1.9.2.6.3	INTEGER	read-write	The BOOTP/DHCP Admin Mode. The relaying functionality can be administratively enabled or disabled by this object
I32 agentBootpDhcpRelayMinWaitTime	1.3.6.1.4.1.4526.1.9.2.6.4	Integer32	read-write	The BOOTP/DHCP Minimum Wait Time. When the BOOTP relay agent receives a BOOTREQUEST message, it MAY use the value of the 'secs' (seconds since client began booting) field of the request as a factor in deciding whether to relay the request or not.
INT agentBootpDhcpRelayCircuitIdOptionMode	1.3.6.1.4.1.4526.1.9.2.6.5	INTEGER	read-write	The BOOTP/DHCP Circuit ID Option Mode. This flag is set to enable/disable the network element to add/remove the DHCP Relay agent Circuit ID sub-options.
I32 agentBootpDhcpRelayNumOfRequestsReceived	1.3.6.1.4.1.4526.1.9.2.6.6	Integer32	read-only	The Number of BOOTP/DHCP Requests Received. Total number of BOOTREQUESTs received from all clients.
I32 agentBootpDhcpRelayNumOfRequestsForwarded	1.3.6.1.4.1.4526.1.9.2.6.7	Integer32	read-only	The Number of BOOTP/DHCP Requests Forwarded. Total number of BOOTREQUESTs forwarded to the next agents/servers.
I32 agentBootpDhcpRelayNumOfDiscards	1.3.6.1.4.1.4526.1.9.2.6.8	Integer32	read-only	The Number of BOOTP/DHCP Discards. Total number of packets discarded by the network element because of error in the packet.

RFC description

Routing configuration MIB for Netgear FSM7326 switch, managing ARP, OSPF, and RIPv2 routing parameters.

Start monitoring Netgear FSM7326 managed switch (Layer 3 routing: OSPF/RIP) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download FSM7326-ROUTING-MIB

What Is FSM7326-ROUTING-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

How to Use in IPNetwork Monitor

RFC description