All MIBs › FASTPATH-ROUTING-MIB
Organization: Broadcom Corporation
Last Updated: 2007-05-23
Category: Technology: Routing, Vendor: Broadcom
Description: Broadcom FastPath private MIB for IPv4 routing configuration including ARP, OSPF, RIP, and VRRP parameters on FastPath switches.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is FASTPATH-ROUTING-MIB?
FASTPATH-ROUTING-MIB is Broadcom's private MIB for IPv4 routing configuration on switches running the FastPath switching software, covering protocols such as ARP, OSPF, RIP, and VRRP. It is intended to expose configuration and status parameters for these routing features, including neighbor/adjacency information and protocol-specific tuning parameters. As a monitoring tool it would primarily support verifying routing protocol operational status and configuration correctness, which reflects the software/control-plane health of the device's routing stack rather than physical hardware; however, no sample object names were available for this module in the provided source. It builds on and interoperates with standard IETF routing MIBs (OSPF-MIB, RIP, VRRP-MIB) as its scope description directly names those protocols. It is deployed on Layer 3 managed switches built on Broadcom's FastPath switching stack wherever IPv4 routing, VRRP redundancy, or dynamic routing protocols are enabled. Network engineers evaluating or troubleshooting this functionality can download the FASTPATH-ROUTING-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in FASTPATH-ROUTING-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Broadcom FastPath-based Layer 3 managed switch
Monitoring Examples
No object/table names were provided for this module, so a concrete polling scenario cannot be grounded in specific OIDs here; based on its stated scope, it would typically expose per-protocol status tables for ARP entries, OSPF neighbor/interface state, RIP routes, and VRRP virtual router status, which an operator would poll to confirm routing adjacencies are up and VRRP failover is functioning as configured.
This MIB depends on
Related MIBs
Imported Objects
From BROADCOM-REF-MIB
| fastPath | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero | |
| ifIndex | OBJECT-TYPE |
From OSPF-MIB
| RouterID | |
| ospfAreaEntry | OBJECT-TYPE |
| ospfIfEntry | |
| ospfVirtIfEntry |
From RFC1213-MIB
| DisplayString | |
| PhysAddress |
From RIPv2-MIB
| rip2IfConfEntry | OBJECT-TYPE |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
From VRRP-MIB
| vrrpOperVrId | OBJECT-TYPE |
How to Use in IPNetwork Monitor
Example using agentDhcpClientMsgsReceived OID:
Select a Broadcom FastPath-based Ethernet switch (multi-vendor OEM) (IPv4 routing: OSPF/RIP/VRRP) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type agentDhcpClientMsgsReceived into the Find box to locate it in the OID tree, then select it and click OK. The Number of DHCP Requests Received. Total number of DHCP requests received from all clients. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| fastPathRouting | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2 | The Broadcom Private MIB for FastPath Routing | ||
| agentSwitchArpGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1 | |||
| I32 agentSwitchArpAgeoutTime | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.1 | Integer32 | read-write | Configures the ARP entry ageout time in seconds. Allowable range: 15-21600 |
| I32 agentSwitchArpResponseTime | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.2 | Integer32 | read-write | Configures the ARP request response timeout in seconds. Allowable range: 1-10 |
| I32 agentSwitchArpMaxRetries | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.3 | Integer32 | read-write | Configures the ARP count of maximum request for retries. Allowable range: 0-10 |
| I32 agentSwitchArpCacheSize | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.4 | Integer32 | read-write | Configures the ARP maximum number of entries in the cache. Allowable range is platform-specific. |
| INT agentSwitchArpDynamicRenew | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.5 | INTEGER | read-write | This indicates the current setting of ARP dynamic renew mode. |
| G32 agentSwitchArpTotalEntryCountCurrent | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.6 | Gauge32 | read-only | Current number of entries in the ARP cache. |
| G32 agentSwitchArpTotalEntryCountPeak | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.7 | Gauge32 | read-only | Peak number of entries recorded in the ARP cache over time. This value is restarted whenever the ARP cache size is changed. |
| G32 agentSwitchArpStaticEntryCountCurrent | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.8 | Gauge32 | read-only | Current number of configured static ARP entries. |
| I32 agentSwitchArpStaticEntryCountMax | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.9 | Integer32 | read-only | Maximum number of configurable static ARP entries. |
| agentSwitchArpTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.10 | not-accessible | This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information. | |
| agentSwitchArpEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.10.1 | not-accessible | ||
| TIK agentSwitchArpAge | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.10.1.1 | TimeTicks | read-only | This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging. |
| IP agentSwitchArpIpAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.10.1.2 | IpAddress | read-only | The IP Address assigned to each interface. |
| PHY agentSwitchArpMacAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.10.1.3 | PhysAddress | read-create | The hardware MAX Address that each interface maps to. |
| I32 agentSwitchArpInterface | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.10.1.4 | Integer32 | read-create | The Associated IfIndex which identified the ARP Entry. |
| INT agentSwitchArpType | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.10.1.5 | INTEGER | read-only | The type of ARP entry. |
| ROW agentSwitchArpStatus | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.10.1.6 | RowStatus | read-write | The status of this ARP entry. Setting this object destroy will remove the entry. |
| agentSwitchLocalProxyArpTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.11 | not-accessible | This table contains the per-interface configuration parameters for Local Proxy Arp. | |
| agentSwitchLocalProxyArpEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.11.1 | not-accessible | Represents a logical row in the agentSwitchLocalProxyArpTable | |
| INT agentSwitchLocalProxyArpMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.11.1.1 | INTEGER | read-write | The Local Proxy Arp Mode for the interface. |
| agentSwitchIntfArpTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.12 | not-accessible | This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information. | |
| agentSwitchIntfArpEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.12.1 | not-accessible | ||
| IP agentSwitchIntfArpIpAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.12.1.1 | IpAddress | not-accessible | The Type of Address assigned to this interface. |
| NUM agentSwitchIntfArpIfIndex | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.12.1.2 | InterfaceIndex | not-accessible | The Associated IfIndex which identified the ARP Entry. This value must be specified for static ARP entries on an unnumbered interface |
| TIK agentSwitchIntfArpAge | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.12.1.3 | TimeTicks | read-only | This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging. |
| PHY agentSwitchIntfArpMacAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.12.1.4 | PhysAddress | read-create | The hardware MAX Address that each interface maps to. |
| INT agentSwitchIntfArpType | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.12.1.5 | INTEGER | read-only | The type of ARP entry. |
| ROW agentSwitchIntfArpStatus | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.1.12.1.6 | RowStatus | read-create | The status of this ARP entry. Setting this object destroy will remove the entry. |
| agentSwitchIpGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2 | |||
| INT agentSwitchIpRoutingMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.1 | INTEGER | read-write | Administratively enables/disables routing on the switch. |
| agentSwitchIpInterfaceTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3 | not-accessible | ||
| agentSwitchIpInterfaceEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1 | not-accessible | ||
| I32 agentSwitchIpInterfaceIfIndex | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.1 | Integer32 | read-only | The IfIndex associated with this instance. |
| IP agentSwitchIpInterfaceIpAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.2 | IpAddress | read-write | The IpAddress assigned to this interface. When setting this value, the value of agentSwitchIpInterfaceNetMask must be set at the same time. |
| IP agentSwitchIpInterfaceNetMask | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.3 | IpAddress | read-write | The NetMask assigned to this interface. When setting this value, the value of agentSwitchIpInterfaceIpAddress must be set at the same time. |
| INT agentSwitchIpInterfaceClearIp | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.4 | INTEGER | read-write | Sets the interfaces IpAddress and NetMask back to 0.0.0.0 |
| INT agentSwitchIpInterfaceRoutingMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.5 | INTEGER | read-write | Enables or disables routing for this interface. |
| INT agentSwitchIpInterfaceProxyARPMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.6 | INTEGER | read-write | Enables or disables Proxy ARP for this interface. |
| U32 agentSwitchIpInterfaceMtuValue | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.7 | Unsigned32 | read-write | Configures the MTU value for this interface. If the value returned is 0 this interface is not enabled for routing. It is not valid to set this value to 0 if routing is enabled. |
| U32 agentSwitchIpInterfaceBandwidth | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.8 | Unsigned32 | read-write | Configures the Bandwidth value for this interface. If the value returned is 0 bandwidth for this interface is not Configured. |
| NUM agentSwitchIpInterfaceUnnumberedIfIndex | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.9 | InterfaceIndexOrZero | read-only | If this object is non-zero, it indicates that the interface is unnumbered, and specifies which interface the address is borrowed from. |
| INT agentSwitchIpInterfaceIcmpUnreachables | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.10 | INTEGER | read-write | If this object is enable, it indicates that ICMP unreachables can be sent on this interface. |
| INT agentSwitchIpInterfaceIcmpRedirects | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.3.1.11 | INTEGER | read-write | If this object is enable and agentSwitchIpIcmpRedirectsMode is also enable ICMP Redirects can be sent on this interface. |
| agentSwitchIpRouterDiscoveryTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.4 | not-accessible | There is no global administrative flag for router discovery. The global routing flag (agentSwitchIpRoutingMode) will be used for this purpose. If routing is disabled, router discovery is disabled as well. | |
| agentSwitchIpRouterDiscoveryEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.4.1 | not-accessible | ||
| I32 agentSwitchIpRouterDiscoveryIfIndex | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.4.1.1 | Integer32 | read-only | Interface Number to configure Router Discovery on. |
| INT agentSwitchIpRouterDiscoveryAdvertiseMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.4.1.2 | INTEGER | read-write | Enable or disable router discovery on the interface. |
| I32 agentSwitchIpRouterDiscoveryMaxAdvertisementInterval | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.4.1.3 | Integer32 | read-write | Maximum time allowed between sending router advertisements from the interface. |
| I32 agentSwitchIpRouterDiscoveryMinAdvertisementInterval | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.4.1.4 | Integer32 | read-write | Minimum time allowed between sending router advertisements from the interface. This value must be less than or equal to agentSwitchIpRouterDiscoveryMaxAdvertisementInterval. |
| I32 agentSwitchIpRouterDiscoveryAdvertisementLifetime | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.4.1.5 | Integer32 | read-write | Value of lifetime field of router advertsisement sent from the interface. This value must be greater than or equal to agentSwitchIpRouterDiscoveryMaxAdvertisementInterval. |
| I32 agentSwitchIpRouterDiscoveryPreferenceLevel | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.4.1.6 | Integer32 | read-write | Preferability of the address as a default router address, related to other addresses on the same subnet. This is defined as the larger the number, the higher the preference. |
| IP agentSwitchIpRouterDiscoveryAdvertisementAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.4.1.7 | IpAddress | read-write | Address used when sending router advertisements from the interface. |
| agentSwitchIpVlanTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.5 | not-accessible | ||
| agentSwitchIpVlanEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.5.1 | not-accessible | A Static VLAN for which routing can be enabled/disabled | |
| I32 agentSwitchIpVlanId | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.5.1.1 | Integer32 | read-only | The Vlan's Id. |
| I32 agentSwitchIpVlanIfIndex | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.5.1.2 | Integer32 | read-only | The IfIndex associated with this VLAN. |
| ROW agentSwitchIpVlanRoutingStatus | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.5.1.3 | RowStatus | read-create | Status of Routing mode per Vlan. active(1) - Vlan is enabled for routing createAndGo(4) - Adds Vlan entry for routing destroy(6) - Removes Vlan from routing |
| agentSwitchSecondaryAddressTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.6 | not-accessible | Contains a list of secondary IP Addresses associated with an interface. | |
| agentSwitchSecondaryAddressEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.6.1 | not-accessible | A secondary IP Address for a given interface. This IP Address must not conflict with the IP Address configured in the agentSwitchIpInterfaceTable. | |
| IP agentSwitchSecondaryIpAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.6.1.1 | IpAddress | not-accessible | The Secondary IP Address assigned to this interface. |
| IP agentSwitchSecondaryNetMask | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.6.1.2 | IpAddress | read-create | The Secondary Net Mask assigned to this interface. This value must be set during creation, and can not be changed. |
| ROW agentSwitchSecondaryStatus | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.6.1.3 | RowStatus | read-create | Creates a new entry in the Secondary Address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The agentSwitchSecondaryNetMask object must be set during creation. destroy(6) - Removes the associated address from the interface. |
| agentSwitchHelperAddressTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.7 | not-accessible | Replaced by agentSwitchIntfIpHelperAddressTable. | |
| agentSwitchHelperAddressEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.7.1 | not-accessible | A Helper IP Address for a given interface. | |
| IP agentSwitchHelperIpAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.7.1.1 | IpAddress | not-accessible | The Helper IP Address assigned to this interface. |
| ROW agentSwitchHelperStatus | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.7.1.2 | RowStatus | read-create | Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The agentSwitchHelperNetMask object must be set during creation. destroy(6) - Removes the associated address from the interface. |
| agentSwitchIpIcmpControlGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.8 | |||
| INT agentSwitchIpIcmpEchoReplyMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.8.1 | INTEGER | read-write | Sets the administrative Echo Reply Mode. |
| INT agentSwitchIpIcmpRedirectsMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.8.2 | INTEGER | read-write | Sets the administrative Mode for sending Redirects. |
| I32 agentSwitchIpIcmpRateLimitInterval | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.8.3 | Integer32 | read-write | Specifies the time interval between tokens being placed in the bucket for ICMP Ratelimit. |
| I32 agentSwitchIpIcmpRateLimitBurstSize | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.8.4 | Integer32 | read-write | Specifies the number of tokens to be placed after timeout. |
| agentSwitchIntfIpHelperAddressTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.10 | not-accessible | Contains a list of IP helper addresses associated with an interface. | |
| agentSwitchIntfIpHelperAddressEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.10.1 | not-accessible | An IP helper address for a given interface. | |
| IP agentSwitchIntfIpHelperIpAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.10.1.1 | IpAddress | not-accessible | An IP helper address for packets received on this interface. An address of 0.0.0.0 identifies the entry as a discard entry. Packets that match a discard entry are dropped. |
| U32 agentSwitchIntfIpHelperUdpPort | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.10.1.2 | Unsigned32 | not-accessible | UDP port number. Received packets with this destination UDP port number are forwarded to the helper address in this entry. |
| T/F agentSwitchIntfIpHelperDiscard | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.10.1.3 | TruthValue | read-write | Variable obsoleted. To create a discard entry, set the helper address to 0.0.0.0. |
| U32 agentSwitchIntfIpHelperHitCount | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.10.1.4 | Unsigned32 | read-only | The number of times a packet has been forwarded or discarded according to this entry. |
| ROW agentSwitchIntfIpHelperStatus | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.2.10.1.5 | RowStatus | read-create | Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry. |
| agentRouterRipConfigGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3 | |||
| INT agentRouterRipAdminState | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.1 | INTEGER | read-write | Sets the administrative mode of RIP in the router. |
| INT agentRouterRipSplitHorizonMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.2 | INTEGER | read-write | Sets the RIP split horizon operating mode in the router. A value of none(1) means split horizon processing is disabled. When set to simple(2), the simple split horizon technique is used. When set to poisonReverse(3), the split horizon with poison reverse technique is used. The default split horizon mode is simple(2). |
| INT agentRouterRipAutoSummaryMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.3 | INTEGER | read-write | Sets the RIP auto summarization mode in the router. A value of enable(1) means that routes advertized by this RIP router are combined, or summarized, whenever possible into aggregates. When set to disable(2), routes are not aggregated in RIP updates generated by this router. The default auto summary mode is enable(1). |
| INT agentRouterRipHostRoutesAcceptMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.4 | INTEGER | read-write | Sets the RIP host route acceptance mode in the router. A value of enable(1) means that host routes advertized to this RIP router will be accepted (learned) into its routing table. When set to disable(2), host routes advertized in RIP updates from neighboring routers are ignored. The default host routes accept mode is enable(1). |
| I32 agentRouterRipDefaultMetric | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.5 | Integer32 | read-write | Default metric of redistributed routes, when RIP redistributes from other protocols. |
| T/F agentRouterRipDefaultMetricConfigured | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.6 | TruthValue | read-write | Flag to determine whether RIP default-metric is configured or not. |
| T/F agentRouterRipDefaultInfoOriginate | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.7 | TruthValue | read-write | Flag to determine, whether RIP can advertise a default-route learned from another protocol. |
| agentRipRouteRedistTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8 | not-accessible | This table contains the MIB objects required to configure route-redistribution for RIP. Here, RIP is the Destination protocol and the source protocols can be any of : BGP, OSPF, Static, Connected. | |
| agentRipRouteRedistEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1 | not-accessible | ||
| INT agentRipRouteRedistSource | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.1 | INTEGER | read-only | Source route, from which RIP can redistribute routes. This object also acts as the identifier for the RIP redistribution Table entry. |
| INT agentRipRouteRedistMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.2 | INTEGER | read-write | User enabels/disables route-redistribution for a particular source protocol. |
| I32 agentRipRouteRedistMetric | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.3 | Integer32 | read-write | Metric used for redistributing a particular source protocol route into RIP. |
| T/F agentRipRouteRedistMetricConfigured | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.4 | TruthValue | read-write | Flag to determine whether RIP redistribute-metric is configured or not. |
| INT agentRipRouteRedistMatchInternal | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.5 | INTEGER | read-write | If this flag is true, RIP redistributes OSPF internal routes. It will be non-applicable, when source protocol is other than ospf. |
| INT agentRipRouteRedistMatchExternal1 | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.6 | INTEGER | read-write | If this flag is true, RIP redistributes OSPF External1 routes. It will be non-applicable, when source protocol is other than ospf. |
| INT agentRipRouteRedistMatchExternal2 | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.7 | INTEGER | read-write | If this flag is true, RIP redistributes OSPF External2 routes. It will be non-applicable, when source protocol is other than ospf. |
| INT agentRipRouteRedistMatchNSSAExternal1 | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.8 | INTEGER | read-write | If this flag is true, RIP redistributes OSPF NSSA-External1 routes. It will be non-applicable, when source protocol is other than ospf. |
| INT agentRipRouteRedistMatchNSSAExternal2 | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.9 | INTEGER | read-write | If this flag is true, RIP redistributes OSPF NSSA-External2 routes. It will be non-applicable, when source protocol is other than ospf. |
| U32 agentRipRouteRedistDistList | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.10 | Unsigned32 | read-write | Access-list number of the access-list, which filters routes received from a source-protocol. |
| T/F agentRipRouteRedistDistListConfigured | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.8.1.11 | TruthValue | read-write | Flag to determine whether Access-list is configured or not. |
| agentRip2IfConfTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.9 | not-accessible | A list of subnets which require separate configuration in RIP. Augments rip2IfConfTable in the RIPv2-MIB. | |
| agentRip2IfConfEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.9.1 | not-accessible | A Single Routing Domain in a single Subnet. Augments rip2IfConfEntry in RIPv2-MIB. | |
| INT agentRip2IfConfAuthKeyId | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.9.1.1 | INTEGER | read-create | The identifier for the authentication key used on this interface. This field is only meaningful when the RIPv2-MIB rip2IfConfAuthType is md5(3); otherwise, the value is not used. |
| INT agentRouterRipRoutePref | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.3.10 | INTEGER | read-create | The route preference, sometimes called administrative distance, for RIP routes. A route with a preference of 255 is considered unreachable. |
| agentRouterOspfConfigGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4 | |||
| I32 agentOspfDefaultMetric | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.1 | Integer32 | read-write | Default metric of redistributed routes, when OSPF redistributes from other protocols. |
| T/F agentOspfDefaultMetricConfigured | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.2 | TruthValue | read-write | Flag to determine whether OSPF default-metric is configured or not. |
| T/F agentOspfDefaultInfoOriginate | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.3 | TruthValue | read-write | Flag to determine, whether OSPF can advertise a default-route learned from another protocol. |
| T/F agentOspfDefaultInfoOriginateAlways | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.4 | TruthValue | read-write | When this flag is true, the router advertises 0.0.0.0/0.0.0.0 always. Without this option, OSPF will only advertise 0.0.0.0/0.0.0.0 if the router's forwarding table contains a default route. |
| I32 agentOspfDefaultInfoOriginateMetric | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.5 | Integer32 | read-write | Metric of the default route, which OSPF advertises when learned from other protocol. (0) indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..16777214). |
| T/F agentOspfDefaultInfoOriginateMetricConfigured | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.6 | TruthValue | read-write | Flag to determine whether OSPF default-info originate metric is configured or not. |
| INT agentOspfDefaultInfoOriginateMetricType | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.7 | INTEGER | read-write | Metric Type of the default route,which OSPF advertises when learned from other protocol. It can be 1(external type 1) or 2(external type 2). |
| agentOspfRouteRedistTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8 | not-accessible | This table contains the MIB objects required to configure route-redistribution for OSPF. Here, OSPF is the Destination protocol and the source protocols can be any of : BGP, RIP, Static, Connected. | |
| agentOspfRouteRedistEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8.1 | not-accessible | ||
| INT agentOspfRouteRedistSource | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8.1.1 | INTEGER | read-only | Source protocol, from which OSPF can redistribute routes. This object also acts as the identifier for the OSPF redistribution Table entry. |
| INT agentOspfRouteRedistMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8.1.2 | INTEGER | read-write | User enabels/disables route-redistribution for a particular source protocol. |
| I32 agentOspfRouteRedistMetric | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8.1.3 | Integer32 | read-write | Metric used for redistributing a particular source protocol route into OSPF. |
| T/F agentOspfRouteRedistMetricConfigured | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8.1.4 | TruthValue | read-write | Flag to determine whether OSPF redistribute-metric is configured or not. |
| INT agentOspfRouteRedistMetricType | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8.1.5 | INTEGER | read-write | Metric Type of routes,which OSPF redistributes from other source protocols. It can be 1(external type 1) or 2(external type 2). |
| U32 agentOspfRouteRedistTag | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8.1.6 | Unsigned32 | read-write | It specifies the tag field in routes redistributed by OSPF. |
| T/F agentOspfRouteRedistSubnets | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8.1.7 | TruthValue | read-write | If this value is false, then OSPF will not redistribute subnetted routes. |
| U32 agentOspfRouteRedistDistList | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8.1.8 | Unsigned32 | read-write | Access-list number of the access-list, which filters routes received from a source-protocol. |
| T/F agentOspfRouteRedistDistListConfigured | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.8.1.9 | TruthValue | read-write | Flag to determine whether Access-list is configured or not. |
| agentOspfIfTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.9 | not-accessible | The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF. Augments ospfIfTable from the OSPF-MIB. | |
| agentOspfIfEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.9.1 | not-accessible | The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF. Augments ospfIfEntry in OSPF-MIB. | |
| INT agentOspfIfAuthKeyId | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.9.1.1 | INTEGER | read-create | The identifier for the authentication key used on this interface. This field is only meaningful when the OSPF-MIB ospfIfAuthType is md5(2); otherwise, the value is not used. |
| INT agentOspfIfIpMtuIgnoreFlag | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.9.1.2 | INTEGER | read-write | Configures the IP MTU Ignore Flag value for this OSPF interface. |
| T/F agentOspfIfPassiveMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.9.1.3 | TruthValue | read-write | Flag to determine whether the interface is passive. A passive interface will not participate in the OSPF adjacency formation. |
| INT agentOspfIfAdvertiseSecondaries | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.9.1.4 | INTEGER | read-write | Configures the advertisability of the secondary addresses configured on this interface. |
| agentOspfVirtIfTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.10 | not-accessible | Information about this router's virtual inter- faces. Augments ospfVirtIfTable from the OSPF-MIB. | |
| agentOspfVirtIfEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.10.1 | not-accessible | Information about a single Virtual Interface. Augments ospfVirtIfEntry in OSPF-MIB. | |
| INT agentOspfVirtIfAuthKeyId | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.10.1.1 | INTEGER | read-create | The identifier for the authentication key used on this virtual interface. This field is only meaningful when the OSPF-MIB ospfVirtIfAuthType is md5(2); otherwise, the value is not used. |
| INT agentRouterOspfRFC1583CompatibilityMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.11 | INTEGER | read-write | From RFC2328: Controls the preference rules used in Section 16.4 when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583 ([Ref9]). When set to 'disabled', the preference rules are those stated in Section 16.4.1, which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas. Set to 'enabled' by default. In order to minimize the chance of routing loops, all OSPF routers in an OSPF routing domain should have RFC1583Compatibility set identically. When there are routers present that have not been updated with the functionality specified in Section 16.4.1 of this memo, all routers should have RFC1583Compatibility set to 'enabled'. Otherwise, all routers should have RFC1583Compatibility set to 'disabled', preventing all routing loops. |
| SPF agentOspfSpfDelayTime | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.12 | SpfTimerRange | read-write | Delay time (in seconds) between when OSPF receives a topology change and when it starts an SPF calculation. It can be an integer from 0 to 65535. The default time is 5 seconds. A value of 0 means that there is no delay; that is, the SPF calculation is started immediately. |
| SPF agentOspfSpfHoldTime | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.13 | SpfTimerRange | read-write | Minimum time (in seconds) between two consecutive SPF calculations. It can be an integer from 0 to 65535. The default time is 10 seconds. A value of 0 means that there is no delay; that is, two SPF calculations can be done, one immediately after the other. |
| AUT agentOspfAutoCostRefBw | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.14 | AutoCostRefBw | read-write | Auto cost refernece bandwidth of the router interafaces for ospf metric calculations. It can be an integer from 1 to 4294967. The default reference bandwidth is 100 Mbps. |
| T/F agentOspfOpaqueLsaSupport | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.15 | TruthValue | read-write | The router's support for Opaque LSA types. This object is persistent and when written the entity SHOULD save the change to non-volatile storage. |
| agentOspfAreaOpaqueLsdbTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.16 | not-accessible | The OSPF Process's Area Link State Database (LSDB). The LSDB contains type-10 Link State Advertisements from throughout the areas that the device is attached to. | |
| agentOspfAreaOpaqueLsdbEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.16.1 | not-accessible | A single AreaOpaque Link State Advertisement. | |
| IP agentOspfAreaOpaqueLsdbAreaId | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.16.1.1 | IpAddress | read-only | The 32 bit identifier of the Area from which the LSA was received. |
| INT agentOspfAreaOpaqueLsdbType | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.16.1.2 | INTEGER | read-only | The type of the link state advertisement. Each link state type has a separate advertisement format. |
| IP agentOspfAreaOpaqueLsdbLsid | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.16.1.3 | IpAddress | read-only | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. |
| IP agentOspfAreaOpaqueLsdbRouterId | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.16.1.4 | IpAddress | read-only | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| I32 agentOspfAreaOpaqueLsdbSequence | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.16.1.5 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 agentOspfAreaOpaqueLsdbAge | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.16.1.6 | Integer32 | read-only | This field is the age of the link state advertisement in seconds. |
| I32 agentOspfAreaOpaqueLsdbChecksum | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.16.1.7 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. |
| OCT agentOspfAreaOpaqueLsdbAdvertisement | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.16.1.8 | OCTET STRING | read-only | The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size |
| agentOspfLocalLsdbTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17 | not-accessible | The OSPF Process's Link-Local Link State Database for non-virtual links. This table is identical to the OSPF LSDB Table in format, but contains only Link-Local Link State Advertisements for non-virtual links. The purpose is to allow Link-Local LSAs to be displayed for each non-virtual interface. This table is implemented to support type-9 LSAs which are defined in 'The OSPF Opaque LSA Option'. | |
| agentOspfLocalLsdbEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17.1 | not-accessible | A single Link State Advertisement. | |
| IP agentOspfLocalLsdbIpAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17.1.1 | IpAddress | read-only | The IP Address of the interface from which the LSA was received if the interface is numbered. |
| NUM agentOspfLocalLsdbAddressLessIf | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17.1.2 | InterfaceIndexOrZero | read-only | The Interface Index of the interface from which the LSA was received if the interface is unnumbered. |
| INT agentOspfLocalLsdbType | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17.1.3 | INTEGER | read-only | The type of the link state advertisement. Each link state type has a separate advertise- ment format. |
| IP agentOspfLocalLsdbLsid | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17.1.4 | IpAddress | read-only | The Link State ID is an LS Type Specific field containing a 32 bit identifier in IP address format; it identifies the piece of the routing domain that is being described by the advertisement. |
| ROU agentOspfLocalLsdbRouterId | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17.1.5 | RouterID | read-only | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| I32 agentOspfLocalLsdbSequence | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17.1.6 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 agentOspfLocalLsdbAge | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17.1.7 | Integer32 | read-only | This field is the age of the link state adver- tisement in seconds. |
| I32 agentOspfLocalLsdbChecksum | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17.1.8 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum. |
| OCT agentOspfLocalLsdbAdvertisement | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.17.1.9 | OCTET STRING | read-only | The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size. |
| agentOspfAsLsdbTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.18 | not-accessible | The OSPF Process's AS-scope LSA Link State Database. The Database contains the AS-scope Link State Advertisements from throughout the areas that the device is attached to. This table is identical to the OSPF LSDB Table in format, but contains only AS-scope Link State Advertisements. The purpose is to allow AS-scope LSAs to be displayed once for the router rather than once in each non-stub area. | |
| agentOspfAsLsdbEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.18.1 | not-accessible | A single Link State Advertisement. | |
| INT agentOspfAsLsdbType | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.18.1.1 | INTEGER | read-only | The type of the link state advertisement. Each link state type has a separate advertise- ment format. |
| IP agentOspfAsLsdbLsid | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.18.1.2 | IpAddress | read-only | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. |
| ROU agentOspfAsLsdbRouterId | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.18.1.3 | RouterID | read-only | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| I32 agentOspfAsLsdbSequence | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.18.1.4 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 agentOspfAsLsdbAge | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.18.1.5 | Integer32 | read-only | This field is the age of the link state adver- tisement in seconds. |
| I32 agentOspfAsLsdbChecksum | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.18.1.6 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum. |
| OCT agentOspfAsLsdbAdvertisement | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.18.1.7 | OCTET STRING | read-only | The entire Link State Advertisement, including its header. |
| T/F agentOspfDefaultPassiveMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.19 | TruthValue | read-write | Flag to determine, whether all the interfaces are passive interfaces by default. A passive interface will not participate in the OSPF adjacency formation. |
| INT agentOspfRoutePrefIntraArea | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.20 | INTEGER | read-write | The route preference, sometimes called administrative distance, for intra-area OSPFv2 routes. A route with a preference of 255 is considered unreachable. |
| INT agentOspfRoutePrefInterArea | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.21 | INTEGER | read-write | The route preference, sometimes called administrative distance, for inter-area OSPFv2 routes. A route with a preference of 255 is considered unreachable. |
| INT agentOspfRoutePrefExternal | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.4.22 | INTEGER | read-write | The route preference, sometimes called administrative distance, for external OSPFv2 routes. A route with a preference of 255 is considered unreachable. |
| agentSnmpTrapFlagsConfigGroupLayer3 | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.5 | |||
| INT agentSnmpVRRPNewMasterTrapFlag | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.5.1 | INTEGER | read-write | This flag enables the sending of VRRP new master notification traps. |
| INT agentSnmpVRRPAuthFailureTrapFlag | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.5.2 | INTEGER | read-write | This flag enables the sending of VRRP authentication failure notification traps. |
| agentBootpDhcpRelayGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.6 | |||
| I32 agentBootpDhcpRelayMaxHopCount | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.6.1 | Integer32 | read-write | The BOOTP/DHCP Max Hop Count. The relay agent silently discards BOOTREQUEST messages whose hops field exceeds the value 16 assuming that the request is looped through the intermediate agents. The default value is 4. |
| IP agentBootpDhcpRelayForwardingIp | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.6.2 | IpAddress | read-write | DHCP server addresses are now configured through IP helper. |
| INT agentBootpDhcpRelayForwardMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.6.3 | INTEGER | read-write | The DHCP relay admin mode is replaced by the IP helper admin mode. |
| I32 agentBootpDhcpRelayMinWaitTime | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.6.4 | Integer32 | read-write | The BOOTP/DHCP Minimum Wait Time. When the BOOTP relay agent receives a BOOTREQUEST message, it MAY use the value of the 'secs' (seconds since client began booting) field of the request as a factor in deciding whether to relay the request or not. |
| INT agentBootpDhcpRelayCircuitIdOptionMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.6.5 | INTEGER | read-write | The BOOTP/DHCP Circuit ID Option Mode. This flag is set to enable/disable the network element to add/remove the DHCP Relay agent Circuit ID sub-options. |
| I32 agentBootpDhcpRelayNumOfRequestsReceived | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.6.6 | Integer32 | read-only | Replaced by IP helper statistics. |
| I32 agentBootpDhcpRelayNumOfRequestsForwarded | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.6.7 | Integer32 | read-only | Replaced by IP helper statistics. |
| I32 agentBootpDhcpRelayNumOfDiscards | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.6.8 | Integer32 | read-only | Replaced by IP helper statistics. |
| agentECMPGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.7 | |||
| I32 agentECMPOspfMaxPaths | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.7.1 | Integer32 | read-write | It sets the number of paths that OSPF can report for a given destination where maxpaths is platform-dependent. |
| agentRouterVrrpConfigGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.8 | |||
| INT agentRouterVrrpAdminState | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.8.1 | INTEGER | read-write | Sets the administrative mode of VRRP in the router. |
| agentRouterVrrpConfiguredTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.8.2 | not-accessible | Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of `agentRouterVrrpConfiguredEntry' items. | |
| agentRouterVrrpConfiguredEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.8.2.1 | not-accessible | An entry in the table contains operational priority that is associated with a virtual router. | |
| I32 agentRouterVrrpConfiguredPriority | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.8.2.1.1 | Integer32 | read-only | This object specifies the value set by the vrrpOperPriority object. The GET operation on 'vrrpOperPriority' will be affected by both the tracking process and the configured priority set by the vrrpOperPriority object. |
| agentVrrpOperations | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.9 | |||
| agentRouterVrrpOperTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.9.1 | not-accessible | Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of `agentRouterVrrpOperEntry' items. | |
| agentRouterVrrpOperEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.9.1.1 | not-accessible | An entry in the table contains operational priority that is associated with a virtual router. | |
| I32 agentRouterVrrpOperPriority | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.9.1.1.1 | Integer32 | read-only | This object specifies the operational priority of the VRRP router. This value will be afftected by both the tracking process and the configured priority set by the vrrpOperPriority object. |
| agentRouterVrrpTrackGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10 | |||
| agentRouterVrrpTrackIntfTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.1 | not-accessible | Tracking table for a VRRP router which consists of agentRouterVrrpTrackIntfEntry items. | |
| agentRouterVrrpTrackIntfEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.1.1 | not-accessible | An entry in the table contains tracked IP interfaces associated with a virtual router. | |
| NUM agentRouterVrrpTrackIntf | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.1.1.1 | InterfaceIndex | read-create | This object specifies the interface to be tracked. |
| I32 agentRouterVrrpTrackIfPrioDec | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.1.1.2 | Integer32 | read-create | This object specifies the decrement priority of the VRRP router. |
| T/F agentRouterVrrpTrackIfState | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.1.1.3 | TruthValue | read-only | This object specifies the IP state of the tracked interface for the virtual router. |
| ROW agentRouterVrrpTrackIfStatus | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.1.1.4 | RowStatus | read-create | The row status variable, used in accordance to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). The newly created row will be in active state later. To destroy the row set this object to destroy. |
| agentRouterVrrpTrackRouteTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.2 | not-accessible | Tracking table for a VRRP router which consists of a 'agentRouterVrrpTrackRouteEntry' items. | |
| agentRouterVrrpTrackRouteEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.2.1 | not-accessible | An entry in the table contains tracked Routes associated with a virtual router. | |
| IP agentRouterVrrpTrackRtPfx | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.2.1.1 | IpAddress | read-create | This object specifies the prefix of the route to be tracked. |
| I32 agentRouterVrrpTrackRtPfxLen | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.2.1.2 | Integer32 | read-create | This object specifies prefix length of the route to be tracked. |
| I32 agentRouterVrrpTrackRtPrioDec | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.2.1.3 | Integer32 | read-create | This object specifies the decrement priority of the VRRP router. |
| T/F agentRouterVrrpTrackRtReachable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.2.1.4 | TruthValue | read-only | This object specifies the reachability of the tracked route. |
| ROW agentRouterVrrpTrackRtStatus | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.10.2.1.5 | RowStatus | read-create | The row status variable, used in accordance to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). The newly created row will be in active state later. To delete the tracked route set this object to destroy. |
| agentIpHelperGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11 | |||
| INT agentIpHelperAdminMode | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.1 | INTEGER | read-write | Administratively enable or disable IP helper. |
| C32 agentDhcpClientMsgsReceivedEx | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.2 | Counter32 | read-only | The Number of DHCP Requests Received. Total number of DHCP requests received from all clients. |
| C32 agentDhcpClientMsgsRelayed | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.3 | Counter32 | read-only | The Number of DHCP Requests Forwarded. Total number of DHCP requests relayed to a server. |
| C32 agentDhcpServerMsgsReceived | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.4 | Counter32 | read-only | The number of DHCP messages received from a server. |
| C32 agentDhcpServerMsgsRelayed | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.5 | Counter32 | read-only | The number of DHCP messages relayed to a server. |
| C32 agentUdpClientMsgsReceived | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.6 | Counter32 | read-only | The number of UDP messages received from all clients. |
| C32 agentUdpClientMsgsRelayed | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.7 | Counter32 | read-only | The number of UDP messages relayed to a server. |
| agentSwitchIpHelperAddressTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.8 | not-accessible | Contains a list of IP helper addresses configured globally. | |
| agentSwitchIpHelperAddressEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.8.1 | not-accessible | An IP Helper address that applies to packets received on any interface. | |
| IP agentSwitchIpHelperAddress | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.8.1.1 | IpAddress | read-write | The IP Helper address assigned to this interface. |
| U32 agentSwitchIpHelperUdpPort | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.8.1.2 | Unsigned32 | read-write | UDP port number. |
| U32 agentSwitchIpHelperHitCount | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.8.1.3 | Unsigned32 | read-only | The number of times a packet has been forwarded or discarded according to this entry. |
| ROW agentSwitchIpHelperStatus | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.8.1.4 | RowStatus | read-create | Creates a new entry in the global IP Helper address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry. |
| C32 agentUdpClientMsgsTtlExpired | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.9 | Counter32 | read-only | The number of UDP messages received with an expired TTL. |
| C32 agentUdpClientMsgsDiscarded | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.11.10 | Counter32 | read-only | The number of UDP messages that matched a discard entry. |
| agentInternalVlanGroup | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.12 | |||
| I32 agentInternalVlanBase | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.12.1 | Integer32 | read-write | The VLAN ID internally assigned to the first port-based routing interface. |
| INT agentInternalVlanPolicy | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.12.2 | INTEGER | read-write | Whether to search up or down from the base VLAN ID for a free VLAN ID to assign to a port-based routing interface. |
| agentSwitchInternalVlanTable | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.12.3 | not-accessible | Contains a list of VLAN IDs used internally for port-based routing interfaces. | |
| agentSwitchInternalVlanEntry | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.12.3.1 | not-accessible | A VLAN ID internally assigned to a port-based routing interface. | |
| I32 agentSwitchInternalVlanId | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.12.3.1.1 | Integer32 | not-accessible | A VLAN ID internally assigned to a port-based routing interface. |
| I32 agentSwitchInternalVlanIfIndex | 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.12.3.1.2 | Integer32 | read-only | Interface index of port-based routing interface using this VLAN ID. |
RFC description
Manages OSPF and RIP routing protocols, ARP, and network switching on Broadcom FastPath platforms.
Start monitoring Broadcom FastPath-based Ethernet switch (multi-vendor OEM) (IPv4 routing: OSPF/RIP/VRRP) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.