All MIBs › EMD-MIB
Organization: Raritan
Last Updated: 2015-10-26
Category: Device Management, Domain: Environmental Monitoring, Domain: Power/UPS
Description: Enterprise monitoring device MIB for managing environmental and infrastructure monitoring sensors and their thresholds.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is EMD-MIB?
EMD-MIB is a vendor-specific Raritan MIB for the EMX Environmental Monitoring Device, used to manage environmental sensor infrastructure in data centers. It exposes device identity and network configuration (name, MAC address, IP/netmask/gateway), hardware and firmware version, and counts of physically attached versus actively managed external sensors. It strongly supports monitoring both hardware status (device hardware/firmware version, network reachability) and environmental sensor health, since a mismatch between total and managed external sensor counts can reveal a disconnected or failed probe, with trap definitions available for sensor-related alerts. Being a Raritan-specific environmental device MIB, it likely complements Raritan's PDU/rack PDU MIBs used in the same data center racks. It is typically deployed in data center or telecom equipment racks to monitor temperature, humidity, or other environmental conditions. Engineers can download the EMD-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in EMD-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Raritan EMX Environmental Monitoring Device
- data center rack environmental sensor hub
Monitoring Examples
deviceName, hardwareVersion, and firmwareVersion identify the EMX unit and confirm it is running current firmware; externalSensorCount and managedExternalSensorCount tell an admin how many environmental probes are physically attached versus actively managed, and a mismatch could indicate a disconnected or failed sensor. deviceInetAddressType/deviceInetIPAddress/deviceInetNetmask/deviceInetGateway confirm the unit's network configuration, and traps under the trapInformation branch would notify an operator of an environmental fault such as a temperature excursion in the monitored rack.
What Can Be Monitored
- device hardware/firmware version
- external sensor count (physical vs managed)
- device network configuration (IP/netmask/gateway)
- device MAC address
- environmental sensor trap conditions
This MIB depends on
Related MIBs
Imported Objects
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType | |
| InetPortNumber |
From RFC1213-MIB
| sysContact | |
| sysLocation | |
| sysName |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 | |
| enterprises |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| raritan | 1.3.6.1.4.1.13742 | This MIB describes the SNMP functions of the EMX Environmental Monitoring Device by Raritan Computer. | ||
| emd | 1.3.6.1.4.1.13742.8 | |||
| traps | 1.3.6.1.4.1.13742.8.0 | |||
| trapInformation | 1.3.6.1.4.1.13742.8.0.0 | |||
| STR userName | 1.3.6.1.4.1.13742.8.0.0.1 | DisplayString | read-only | The user currently logged in. |
| STR targetUser | 1.3.6.1.4.1.13742.8.0.0.2 | DisplayString | read-only | The user added, deleted, or modified. |
| STR imageVersion | 1.3.6.1.4.1.13742.8.0.0.3 | DisplayString | read-only | The version of the upgrade image. |
| STR roleName | 1.3.6.1.4.1.13742.8.0.0.4 | DisplayString | read-only | The role added, deleted, or modified. |
| STR smtpMessageRecipients | 1.3.6.1.4.1.13742.8.0.0.5 | DisplayString | read-only | Comma separated list of SMTP Message recipients |
| STR smtpServer | 1.3.6.1.4.1.13742.8.0.0.6 | DisplayString | read-only | The IP address/host name of the SMTP server |
| SEN oldSensorState | 1.3.6.1.4.1.13742.8.0.0.7 | SensorStateEnumeration | accessible-for-notify | The old sensor state used in Sensor State Transition traps. |
| I32 externalSensorNumber | 1.3.6.1.4.1.13742.8.0.0.8 | Integer32 | accessible-for-notify | A unique value for each sensor. Its value ranges between 1 and the value of externalSensorCount. |
| SEN typeOfSensor | 1.3.6.1.4.1.13742.8.0.0.9 | SensorTypeEnumeration | accessible-for-notify | The type of sensor. |
| STR errorDescription | 1.3.6.1.4.1.13742.8.0.0.10 | DisplayString | accessible-for-notify | Description of the Error |
| DEV deviceChangedParameter | 1.3.6.1.4.1.13742.8.0.0.11 | DeviceIdentificationParameterEnumeration | accessible-for-notify | Description of the parameter(s) that changed. |
| STR changedParameterNewValue | 1.3.6.1.4.1.13742.8.0.0.12 | DisplayString | accessible-for-notify | The new value of the changed parameter |
| T/F lhxSupportEnabled | 1.3.6.1.4.1.13742.8.0.0.13 | TruthValue | accessible-for-notify | The new enabled state for Schroff LHX Support. |
| STR webcamModel | 1.3.6.1.4.1.13742.8.0.0.14 | DisplayString | accessible-for-notify | The model of the Webcam |
| STR webcamConnectionPort | 1.3.6.1.4.1.13742.8.0.0.15 | DisplayString | accessible-for-notify | The port to which the Webcam is connected |
| STR peripheralDeviceRomcode | 1.3.6.1.4.1.13742.8.0.0.16 | DisplayString | accessible-for-notify | The Romcode of an peripheral device |
| PER peripheralDeviceFirmwareUpdateState | 1.3.6.1.4.1.13742.8.0.0.17 | PeripheralDeviceFirmwareUpdateStateEnumeration | accessible-for-notify | The firmware update state of an peripheral device |
| INE agentInetPortNumber | 1.3.6.1.4.1.13742.8.0.0.18 | InetPortNumber | accessible-for-notify | The UDP port number used for accessing the SNMP agent on the device. Examples: If deviceCascadeType is portForwarding, then master: 50500 slave 1:50501 slave 2: 50502 ...... If cascading mode is not portForwarding and default (Standard) ports are being used, then port: 161 |
| STR phoneNumber | 1.3.6.1.4.1.13742.8.0.0.19 | DisplayString | accessible-for-notify | The phone number of e.g. an SMS receiver. |
| NTF systemStarted | 1.3.6.1.4.1.13742.8.0.1 | The system has started. | ||
| NTF systemReset | 1.3.6.1.4.1.13742.8.0.2 | The system was reset. The conditions under which this trap is sent include, but are not limited to, the following. using the GUI - Maintenance->Reset Unit using the CLI - reset emd unit | ||
| NTF userLogin | 1.3.6.1.4.1.13742.8.0.3 | A user logged in. | ||
| NTF userLogout | 1.3.6.1.4.1.13742.8.0.4 | A user logged out. | ||
| NTF userAuthenticationFailure | 1.3.6.1.4.1.13742.8.0.5 | A user authentication attempt failed. | ||
| NTF userSessionTimeout | 1.3.6.1.4.1.13742.8.0.6 | A user timed out from the device. | ||
| NTF userAdded | 1.3.6.1.4.1.13742.8.0.7 | A user was added to the system. | ||
| NTF userModified | 1.3.6.1.4.1.13742.8.0.8 | A user account was modified. | ||
| NTF userDeleted | 1.3.6.1.4.1.13742.8.0.9 | A user was deleted from the system. | ||
| NTF roleAdded | 1.3.6.1.4.1.13742.8.0.10 | A role was added to the system. | ||
| NTF roleModified | 1.3.6.1.4.1.13742.8.0.11 | A role was modified. | ||
| NTF roleDeleted | 1.3.6.1.4.1.13742.8.0.12 | A role was deleted from the system. | ||
| NTF deviceUpdateStarted | 1.3.6.1.4.1.13742.8.0.13 | The device update has started. | ||
| NTF deviceUpdateCompleted | 1.3.6.1.4.1.13742.8.0.14 | The device update has completed. | ||
| NTF userBlocked | 1.3.6.1.4.1.13742.8.0.15 | A blocked user tried to log in. | ||
| NTF userPasswordChanged | 1.3.6.1.4.1.13742.8.0.16 | User password was changed. | ||
| NTF passwordSettingsChanged | 1.3.6.1.4.1.13742.8.0.17 | Strong password settings changed. | ||
| NTF firmwareValidationFailed | 1.3.6.1.4.1.13742.8.0.18 | Firmware validation failed. | ||
| NTF logFileCleared | 1.3.6.1.4.1.13742.8.0.19 | The log file has been cleared. | ||
| NTF bulkConfigurationSaved | 1.3.6.1.4.1.13742.8.0.20 | Bulk Configuration saved. | ||
| NTF bulkConfigurationCopied | 1.3.6.1.4.1.13742.8.0.21 | Bulk Configuration saved. | ||
| NTF externalSensorStateChange | 1.3.6.1.4.1.13742.8.0.22 | External Sensor State Change. | ||
| NTF smtpMessageTransmissionFailure | 1.3.6.1.4.1.13742.8.0.23 | SMTP message transmission failure | ||
| NTF ldapError | 1.3.6.1.4.1.13742.8.0.24 | LDAP Error occurred; errorDescription describes the error | ||
| NTF deviceUpdateFailed | 1.3.6.1.4.1.13742.8.0.25 | The device update has failed. | ||
| NTF pingServerEnabled | 1.3.6.1.4.1.13742.8.0.26 | The ping feature has been enabled | ||
| NTF pingServerDisabled | 1.3.6.1.4.1.13742.8.0.27 | The ping feature has been disabled | ||
| NTF serverNotReachable | 1.3.6.1.4.1.13742.8.0.28 | The server is not reachable | ||
| NTF serverReachable | 1.3.6.1.4.1.13742.8.0.29 | The server is reachable | ||
| NTF deviceIdentificationChanged | 1.3.6.1.4.1.13742.8.0.30 | Device identification has changed | ||
| NTF usbSlaveConnected | 1.3.6.1.4.1.13742.8.0.31 | USB Connectivity to slave has been established | ||
| NTF usbSlaveDisconnected | 1.3.6.1.4.1.13742.8.0.32 | USB Connectivity to slave has been lost | ||
| NTF lhxSupportChanged | 1.3.6.1.4.1.13742.8.0.33 | The Schroff LHX Support changed to state 'lhxSupportEnabled'. | ||
| NTF userAcceptedRestrictedServiceAgreement | 1.3.6.1.4.1.13742.8.0.34 | The user accepted the Restricted Service Agreement. | ||
| NTF userDeclinedRestrictedServiceAgreement | 1.3.6.1.4.1.13742.8.0.35 | The user declined the Restricted Service Agreement. | ||
| NTF deviceSettingsSaved | 1.3.6.1.4.1.13742.8.0.36 | Device Settings have been saved. | ||
| NTF deviceSettingsRestored | 1.3.6.1.4.1.13742.8.0.37 | Device Settings have been restored. | ||
| NTF webcamInserted | 1.3.6.1.4.1.13742.8.0.38 | A webcam has been inserted | ||
| NTF webcamRemoved | 1.3.6.1.4.1.13742.8.0.39 | A webcam has been removed | ||
| NTF serverConnectivityUnrecoverable | 1.3.6.1.4.1.13742.8.0.40 | The connection to the server could not be recovered | ||
| NTF radiusError | 1.3.6.1.4.1.13742.8.0.41 | LDAP Error occurred; errorDescription describes the error | ||
| NTF serverReachabilityError | 1.3.6.1.4.1.13742.8.0.42 | Server Reachability Error occurred; errorDescription describes the error. This trap is sent when the Error state is entered. Reasons for transitioning to the Error state include the following: Unable to resolve the server hostname. | ||
| NTF unknownPeripheralDeviceAttached | 1.3.6.1.4.1.13742.8.0.43 | An unknown peripheral device was attached. | ||
| NTF peripheralDeviceFirmwareUpdate | 1.3.6.1.4.1.13742.8.0.44 | The firmware update state of a peripheral device changed while performing update to peripheralDevicePackageFirmwareVersion. | ||
| NTF smsMessageTransmissionFailure | 1.3.6.1.4.1.13742.8.0.45 | Sending an SMS message failed. | ||
| configuration | 1.3.6.1.4.1.13742.8.1 | |||
| unit | 1.3.6.1.4.1.13742.8.1.1 | |||
| unitConfiguration | 1.3.6.1.4.1.13742.8.1.1.1 | |||
| STR deviceName | 1.3.6.1.4.1.13742.8.1.1.1.1 | DisplayString | read-write | The user-defined name for the EMD. |
| STR hardwareVersion | 1.3.6.1.4.1.13742.8.1.1.1.2 | DisplayString | read-only | The main boards hardware version. |
| STR firmwareVersion | 1.3.6.1.4.1.13742.8.1.1.1.3 | DisplayString | read-only | The firmware version. |
| STR utcOffset | 1.3.6.1.4.1.13742.8.1.1.1.4 | DisplayString | read-only | The current UTC offset. |
| I32 externalSensorCount | 1.3.6.1.4.1.13742.8.1.1.1.5 | Integer32 | read-only | The number of external sensors. |
| I32 managedExternalSensorCount | 1.3.6.1.4.1.13742.8.1.1.1.6 | Integer32 | read-only | The number of managed external sensors |
| EXT externalSensorsZCoordinateUnits | 1.3.6.1.4.1.13742.8.1.1.1.7 | ExternalSensorsZCoordinateUnitsEnumeration | read-write | External Sensor Z Coordinate units: Freeform Text or Rack Units (U). Default is U. |
| MAC deviceMACAddress | 1.3.6.1.4.1.13742.8.1.1.1.8 | MacAddress | read-only | The current MAC address. |
| IPt deviceInetAddressType | 1.3.6.1.4.1.13742.8.1.1.1.9 | InetAddressType | read-only | The type of address format |
| IP deviceInetIPAddress | 1.3.6.1.4.1.13742.8.1.1.1.10 | InetAddress | read-only | The current IP address. A value of 0.0.0.0 indicates an error or an unset option. |
| IP deviceInetNetmask | 1.3.6.1.4.1.13742.8.1.1.1.11 | InetAddress | read-only | The current netmask. A value of 0.0.0.0 indicates an error or an unset option. |
| IP deviceInetGateway | 1.3.6.1.4.1.13742.8.1.1.1.12 | InetAddress | read-only | The current gateway. A value of 0.0.0.0 indicates an error or an unset option. |
| I32 serverCount | 1.3.6.1.4.1.13742.8.1.1.1.13 | Integer32 | read-only | The number of entries in serverReachabilityTable |
| STR model | 1.3.6.1.4.1.13742.8.1.1.1.14 | DisplayString | read-only | The EMD device model. |
| T/F cascadedDeviceConnected | 1.3.6.1.4.1.13742.8.1.1.1.15 | TruthValue | read-only | Indicates whether a device is connected using an USB cable to the USB-A port of this EMX in a cascaded configuration. true: Connected false: Not Connected |
| T/F peripheralDevicesAutoManagement | 1.3.6.1.4.1.13742.8.1.1.1.16 | TruthValue | read-write | Set enabled state of auto management for new peripheral devices. |
| T/F synchronizeWithNTPServer | 1.3.6.1.4.1.13742.8.1.1.1.17 | TruthValue | read-write | Set enabled state of the device's NTP client. |
| T/F useDHCPProvidedNTPServer | 1.3.6.1.4.1.13742.8.1.1.1.18 | TruthValue | read-write | Enable usage of the DHCP/BOOTP provided NTP server addresses; the value is used only if synchronizeWithNTPServer is enabled. |
| IPt firstNTPServerAddressType | 1.3.6.1.4.1.13742.8.1.1.1.19 | InetAddressType | read-write | Represents the type of firstNTPServerAddress. |
| IP firstNTPServerAddress | 1.3.6.1.4.1.13742.8.1.1.1.20 | InetAddress | read-write | The address of the primary NTP server. |
| IPt secondNTPServerAddressType | 1.3.6.1.4.1.13742.8.1.1.1.21 | InetAddressType | read-write | Represents the type of secondNTPServerAddress. |
| IP secondNTPServerAddress | 1.3.6.1.4.1.13742.8.1.1.1.22 | InetAddress | read-write | The address of the secondary NTP server. |
| logConfiguration | 1.3.6.1.4.1.13742.8.1.1.2 | |||
| T/F dataLogging | 1.3.6.1.4.1.13742.8.1.1.2.1 | TruthValue | read-write | Data Retrieval: enabled/disabled. |
| I32 measurementPeriod | 1.3.6.1.4.1.13742.8.1.1.2.2 | Integer32 | read-only | Data Collection periodicity. This is the periodicity of the data collected by the PX. This value is fixed at 1 second. |
| I32 measurementsPerLogEntry | 1.3.6.1.4.1.13742.8.1.1.2.3 | Integer32 | read-write | The number of measurements used for each entry in the log. |
| I32 logSize | 1.3.6.1.4.1.13742.8.1.1.2.4 | Integer32 | read-only | The number of entries in the log. |
| T/F dataLoggingEnableForAllSensors | 1.3.6.1.4.1.13742.8.1.1.2.5 | TruthValue | read-write | Operation to control data logging for all sensors. If this OID is set to true, then all xxxSensorLogAvailable are set to true If this OID is set to false, then all xxxSensorLogAvailable are set to false |
| externalSensors | 1.3.6.1.4.1.13742.8.1.2 | |||
| externalSensorConfigurationTable | 1.3.6.1.4.1.13742.8.1.2.1 | not-accessible | A list of externalSensor configuration entries. The number of entries is given by the value of externalSensorCount for the EMD. | |
| externalSensorConfigurationEntry | 1.3.6.1.4.1.13742.8.1.2.1.1 | not-accessible | An entry containing parameters for an external sensor. | |
| I32 sensorID | 1.3.6.1.4.1.13742.8.1.2.1.1.1 | Integer32 | not-accessible | A unique value for each sensor. Its value ranges between 1 and the value of externalSensorCount. |
| SEN externalSensorType | 1.3.6.1.4.1.13742.8.1.2.1.1.2 | SensorTypeEnumeration | read-only | The type of sensor. |
| STR externalSensorSerialNumber | 1.3.6.1.4.1.13742.8.1.2.1.1.3 | DisplayString | read-only | The sensor serial number. |
| STR externalSensorName | 1.3.6.1.4.1.13742.8.1.2.1.1.4 | DisplayString | read-write | The user-defined name. |
| STR externalSensorDescription | 1.3.6.1.4.1.13742.8.1.2.1.1.5 | DisplayString | read-write | The user-defined description. |
| STR externalSensorXCoordinate | 1.3.6.1.4.1.13742.8.1.2.1.1.6 | DisplayString | read-write | The X coordinate. |
| STR externalSensorYCoordinate | 1.3.6.1.4.1.13742.8.1.2.1.1.7 | DisplayString | read-write | The Y coordinate. |
| STR externalSensorZCoordinate | 1.3.6.1.4.1.13742.8.1.2.1.1.8 | DisplayString | read-write | The Z coordinate. |
| I32 externalSensorChannelNumber | 1.3.6.1.4.1.13742.8.1.2.1.1.9 | Integer32 | read-only | The channel number, applies only to contact sensors; -1 for other sensors |
| SEN externalOnOffSensorSubtype | 1.3.6.1.4.1.13742.8.1.2.1.1.10 | SensorTypeEnumeration | read-write | Type of measurement in case sensor type is discrete OnOff |
| SEN externalSensorUnits | 1.3.6.1.4.1.13742.8.1.2.1.1.11 | SensorUnitsEnumeration | read-only | The base units. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| U32 externalSensorDecimalDigits | 1.3.6.1.4.1.13742.8.1.2.1.1.12 | Unsigned32 | read-only | The number of digits displayed to the right of the decimal point This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| HUN externalSensorAccuracy | 1.3.6.1.4.1.13742.8.1.2.1.1.13 | HundredthsOfAPercentage | read-only | The accuracy: how close (in percent) the measurement is to the actual value. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| U32 externalSensorResolution | 1.3.6.1.4.1.13742.8.1.2.1.1.14 | Unsigned32 | read-only | The resolution: the minimum difference between any two measured values. The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| U32 externalSensorTolerance | 1.3.6.1.4.1.13742.8.1.2.1.1.15 | Unsigned32 | read-only | The resolution: the difference between a sensor value and the actual value. The value of this OID variable should be scaled by (externalSensorDecimalDigits + 1). For example, if the value is 50 and externalSensorDecimalDigits is 2, then actual value is 0.05. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| I32 externalSensorMaximum | 1.3.6.1.4.1.13742.8.1.2.1.1.16 | Integer32 | read-only | The largest possible value The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| I32 externalSensorMinimum | 1.3.6.1.4.1.13742.8.1.2.1.1.17 | Integer32 | read-only | The smallest possible value The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| U32 externalSensorHysteresis | 1.3.6.1.4.1.13742.8.1.2.1.1.18 | Unsigned32 | read-write | The hysteresis used for deassertions The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| U32 externalSensorStateChangeDelay | 1.3.6.1.4.1.13742.8.1.2.1.1.19 | Unsigned32 | read-write | The delay measured in samples before a state is asserted. If the value is zero, then the state is asserted as soon as it is detected; if it is non-zero, say n, then the assertion condition must exist for n+1 consecutive samples before the corresponding assertion event is reported. At present, this value cannot be written (set) |
| I32 externalSensorLowerCriticalThreshold | 1.3.6.1.4.1.13742.8.1.2.1.1.20 | Integer32 | read-write | The lower critical threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| I32 externalSensorLowerWarningThreshold | 1.3.6.1.4.1.13742.8.1.2.1.1.21 | Integer32 | read-write | The lower non-critical (warning) threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| I32 externalSensorUpperCriticalThreshold | 1.3.6.1.4.1.13742.8.1.2.1.1.22 | Integer32 | read-write | The upper critical threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| I32 externalSensorUpperWarningThreshold | 1.3.6.1.4.1.13742.8.1.2.1.1.23 | Integer32 | read-write | The upper non-critical (warning) threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| BIT externalSensorEnabledThresholds | 1.3.6.1.4.1.13742.8.1.2.1.1.24 | Bits | read-write | A bit string which indicates which thresholds are enabled. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors |
| STR externalSensorPort | 1.3.6.1.4.1.13742.8.1.2.1.1.25 | DisplayString | read-only | The position of the sensor. The format is a semicolon separated list of Keyword:value pairs - Keyword1:Value1;Keyword2:value2;... Keyword can be one of the following: ONBOARD, DEVICE-1WIREPORT, HUBPORT, CHAIN-POSITION Examples 1) Onboard Sensor ONBOARD:CC1 2) Old sensor connected to device 1-wire port DEVICE-1WIREPORT:2 3) New style sensor connected to device 1-wire port DEVICE-1WIREPORT:2;CHAIN-POSITION:3 4) New style sensor connected to hub port 3 DEVICE-1WIREPORT:2;CHAIN-POSITION:1;HUBPORT:3;CHAIN-POSITION:1 5) Old style sensor connected to end of new style sensor chain DEVICE-1WIREPORT:2; |
| T/F externalSensorIsActuator | 1.3.6.1.4.1.13742.8.1.2.1.1.26 | TruthValue | read-only | Is this an actuator? True: It is an actuator False: It is not an actuator |
| I32 externalSensorAlarmedToNormalDelay | 1.3.6.1.4.1.13742.8.1.2.1.1.27 | Integer32 | read-write | The delay in seconds for transitions from the alarmed state to the normal state. If the sensor type is motionDetection, then it can set to a value greater >= 0 For all other sensor types, the value is 0 and cannot be set to any other value. |
| T/F externalSensorUseDefaultThresholds | 1.3.6.1.4.1.13742.8.1.2.1.1.28 | TruthValue | read-write | Use default thresholds for this sensor? True: Use default thresholds for this sensor False: Do not use default thresholds for this sensor |
| externalSensorTypeDefaultThresholdsTable | 1.3.6.1.4.1.13742.8.1.2.4 | not-accessible | A list of entries listing the default thresholds for each sensor type. | |
| externalSensorTypeDefaultThresholdsEntry | 1.3.6.1.4.1.13742.8.1.2.4.1 | not-accessible | An entry containing default thresholds for a sensor type. | |
| U32 externalSensorTypeDefaultHysteresis | 1.3.6.1.4.1.13742.8.1.2.4.1.3 | Unsigned32 | read-write | The hysteresis used for deassertions The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| U32 externalSensorTypeDefaultStateChangeDelay | 1.3.6.1.4.1.13742.8.1.2.4.1.4 | Unsigned32 | read-write | The delay measured in samples before a state is asserted. If the value is zero, then the state is asserted as soon as it is detected; if it is non-zero, say n, then the assertion condition must exist for n+1 consecutive samples before the corresponding assertion event is reported. At present, this value cannot be written (set) |
| I32 externalSensorTypeDefaultLowerCriticalThreshold | 1.3.6.1.4.1.13742.8.1.2.4.1.5 | Integer32 | read-write | The lower critical threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| I32 externalSensorTypeDefaultLowerWarningThreshold | 1.3.6.1.4.1.13742.8.1.2.4.1.6 | Integer32 | read-write | The lower non-critical (warning) threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| I32 externalSensorTypeDefaultUpperCriticalThreshold | 1.3.6.1.4.1.13742.8.1.2.4.1.7 | Integer32 | read-write | The upper critical threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| I32 externalSensorTypeDefaultUpperWarningThreshold | 1.3.6.1.4.1.13742.8.1.2.4.1.8 | Integer32 | read-write | The upper non-critical (warning) threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| BIT externalSensorTypeDefaultEnabledThresholds | 1.3.6.1.4.1.13742.8.1.2.4.1.9 | Bits | read-write | A bit string which indicates which thresholds are enabled. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors |
| peripheralDevicePackageTable | 1.3.6.1.4.1.13742.8.1.2.5 | not-accessible | A list of entries for the peripheral Device Packages connected to an EMX. The number of entries is given by the value of peripheralDevicePackagesCount. | |
| peripheralDevicePackageEntry | 1.3.6.1.4.1.13742.8.1.2.5.1 | not-accessible | An entry containing objects for a controller. | |
| I32 peripheralDevicePackageId | 1.3.6.1.4.1.13742.8.1.2.5.1.1 | Integer32 | not-accessible | A unique value for each peripheral device package. |
| STR peripheralDevicePackageSerialNumber | 1.3.6.1.4.1.13742.8.1.2.5.1.3 | DisplayString | read-only | The peripheral device package serial number. |
| STR peripheralDevicePackageModel | 1.3.6.1.4.1.13742.8.1.2.5.1.4 | DisplayString | read-only | The peripheral device package model. Examples are DX-D2C6, DPX2-T1, DPX2-T1H1, DPX2-T2H1, DPX2-T3H1 |
| STR peripheralDevicePackageFirmwareVersion | 1.3.6.1.4.1.13742.8.1.2.5.1.5 | DisplayString | read-only | The peripheral device package firmware version. |
| STR peripheralDevicePackageMinFirmwareVersion | 1.3.6.1.4.1.13742.8.1.2.5.1.6 | DisplayString | read-only | The peripheral device package minimum firmware version. This field may be empty. If it is not empty, then it shall not be possible to downgrade the peripheral device firmware to a version < minimum firmware version number. |
| U32 peripheralDevicePackageFirmwareTimeStamp | 1.3.6.1.4.1.13742.8.1.2.5.1.7 | Unsigned32 | read-only | The time when the peripheralDevicePackage firmware was updated in UNIX(epoch)time. It is measured in seconds relative to January 1, 1970 (midnight UTC/GMT), i.e a value of 0 indicates January 1, 1970 (midnight UTC/GMT). |
| STR peripheralDevicePackagePosition | 1.3.6.1.4.1.13742.8.1.2.5.1.8 | DisplayString | read-only | The position of the package. The format is a semicolon separated list of Keyword:value pairs - Keyword1:Value1;Keyword2:value2;... Keyword can be one of the following: ONBOARD, DEVICE-1WIREPORT, HUBPORT, CHAIN-POSITION Examples 1) Onboard Sensor ONBOARD:CC1 2) Old sensor connected to device 1-wire port DEVICE-1WIREPORT:2 3) New style sensor connected to device 1-wire port DEVICE-1WIREPORT:2;CHAIN-POSITION:3 4) New style sensor connected to hub port 3 DEVICE-1WIREPORT:2;CHAIN-POSITION:1;HUBPORT:3;CHAIN-POSITION:1 5) Old style sensor connected to end of new style sensor chain DEVICE-1WIREPORT:2; |
| STR peripheralDevicePackageState | 1.3.6.1.4.1.13742.8.1.2.5.1.9 | DisplayString | read-only | The state of the package. |
| serverReachability | 1.3.6.1.4.1.13742.8.1.3 | |||
| serverReachabilityTable | 1.3.6.1.4.1.13742.8.1.3.1 | not-accessible | A list of server entries. The number of entries is given by the value of serverCount for the EMD. | |
| serverReachabilityEntry | 1.3.6.1.4.1.13742.8.1.3.1.1 | not-accessible | An entry containing parameters for a server. | |
| I32 serverID | 1.3.6.1.4.1.13742.8.1.3.1.1.1 | Integer32 | not-accessible | A unique value for each server. Its value ranges between 1 and the value of serverCount for that EMD |
| STR serverIPAddress | 1.3.6.1.4.1.13742.8.1.3.1.1.2 | DisplayString | read-only | The IP Address/host name of the server |
| T/F serverPingEnabled | 1.3.6.1.4.1.13742.8.1.3.1.1.3 | TruthValue | read-write | Is ping enabled for this server? |
| measurements | 1.3.6.1.4.1.13742.8.2 | |||
| measurementsExternalSensor | 1.3.6.1.4.1.13742.8.2.1 | |||
| externalSensorMeasurementsTable | 1.3.6.1.4.1.13742.8.2.1.1 | not-accessible | A list of external sensor entries. The number of entries is given by the value of externalSensorCount for the EMD. | |
| externalSensorMeasurementsEntry | 1.3.6.1.4.1.13742.8.2.1.1.1 | not-accessible | An entry containing measurement objects for an external sensor. | |
| T/F measurementsExternalSensorIsAvailable | 1.3.6.1.4.1.13742.8.2.1.1.1.1 | TruthValue | read-only | Is the sensor available? |
| SEN measurementsExternalSensorState | 1.3.6.1.4.1.13742.8.2.1.1.1.2 | SensorStateEnumeration | read-only | The sensor state. |
| I32 measurementsExternalSensorValue | 1.3.6.1.4.1.13742.8.2.1.1.1.3 | Integer32 | read-only | The sensor reading. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors. |
| U32 measurementsExternalSensorTimeStamp | 1.3.6.1.4.1.13742.8.2.1.1.1.4 | Unsigned32 | read-only | The sensor reading timestamp. |
| compliances | 1.3.6.1.4.1.13742.8.3.1 | |||
| complianceRev1 | 1.3.6.1.4.1.13742.8.3.1.1 | The requirements for conformance to the EMD-MIB. | ||
| groups | 1.3.6.1.4.1.13742.8.3.2 | |||
| configGroup | 1.3.6.1.4.1.13742.8.3.2.1 | A collection of objects representing configuration data. | ||
| measurementsGroup | 1.3.6.1.4.1.13742.8.3.2.2 | A collection of objects providing the measurement capability of EMD. | ||
| trapInformationGroup | 1.3.6.1.4.1.13742.8.3.2.3 | A collection of objects providing information in the traps. | ||
| trapsGroup | 1.3.6.1.4.1.13742.8.3.2.4 | A collection of traps. | ||
| logGroup | 1.3.6.1.4.1.13742.8.3.2.5 | A collection of objects providing the logging capabilities about the EMD. | ||
| controlGroup | 1.3.6.1.4.1.13742.8.3.2.6 | A collection of objects providing the ability to control actuators of the EMD. | ||
| log | 1.3.6.1.4.1.13742.8.4 | |||
| logUnit | 1.3.6.1.4.1.13742.8.4.1 | |||
| I32 oldestLogID | 1.3.6.1.4.1.13742.8.4.1.1 | Integer32 | read-only | The index of the oldest data in the buffer for this EMD. |
| I32 newestLogID | 1.3.6.1.4.1.13742.8.4.1.2 | Integer32 | read-only | The index of the newest data in the buffer for this EMD. |
| logTimeStampTable | 1.3.6.1.4.1.13742.8.4.1.3 | not-accessible | A list of entries containing the timestamps of the entries in the log. | |
| logTimeStampEntry | 1.3.6.1.4.1.13742.8.4.1.3.1 | not-accessible | An entry containing the timestamp for log entries. | |
| I32 logIndex | 1.3.6.1.4.1.13742.8.4.1.3.1.1 | Integer32 | not-accessible | A unique value for each entry in the log. Its value ranges between 1 and the value of logSize. |
| U32 logTimeStamp | 1.3.6.1.4.1.13742.8.4.1.3.1.2 | Unsigned32 | read-only | The time when the data was collected. It is measured in seconds relative to January 1, 1970 (midnight UTC/GMT), i.e a value of 0 indicates January 1, 1970 (midnight UTC/GMT). |
| logExternalSensor | 1.3.6.1.4.1.13742.8.4.2 | |||
| externalSensorLogTable | 1.3.6.1.4.1.13742.8.4.2.1 | not-accessible | A list of external sensor entries. The number of entries is given by the value of externalSensorCount for the EMD. | |
| externalSensorLogEntry | 1.3.6.1.4.1.13742.8.4.2.1.1 | not-accessible | An entry containing log objects for an external sensor. | |
| T/F logExternalSensorDataAvailable | 1.3.6.1.4.1.13742.8.4.2.1.1.2 | TruthValue | read-only | Is data available for this sensor during this measurement period? |
| SEN logExternalSensorState | 1.3.6.1.4.1.13742.8.4.2.1.1.3 | SensorStateEnumeration | read-only | The sensor state. |
| I32 logExternalSensorAvgValue | 1.3.6.1.4.1.13742.8.4.2.1.1.4 | Integer32 | read-only | The sensor reading average value. |
| I32 logExternalSensorMaxValue | 1.3.6.1.4.1.13742.8.4.2.1.1.5 | Integer32 | read-only | The sensor reading maximum value. |
| I32 logExternalSensorMinValue | 1.3.6.1.4.1.13742.8.4.2.1.1.6 | Integer32 | read-only | The sensor reading minimum value. |
| control | 1.3.6.1.4.1.13742.8.5 | |||
| actuatorControl | 1.3.6.1.4.1.13742.8.5.1 | |||
| actuatorControlTable | 1.3.6.1.4.1.13742.8.5.1.1 | not-accessible | A list of actuators for an EMX. | |
| actuatorControlEntry | 1.3.6.1.4.1.13742.8.5.1.1.1 | not-accessible | An entry for implementing user-initiated state changes for an actuator. | |
| SEN actuatorState | 1.3.6.1.4.1.13742.8.5.1.1.1.1 | SensorStateEnumeration | read-write | The actuator state. A Get operation retrieves the state of the actuator. A Set operation changes the stae of the sensor. The valid states for set operations are on and Off. Attempting to set the state to any other value will generate an error. |
RFC description
Raritan EMX Environmental Monitoring Device MIB defining sensors, thresholds, and notifications for temperature, power, and environmental conditions.
Start monitoring Raritan EMX Environmental Monitoring Device with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.