E5-120-IESCOMMON-MIB

All MIBs › E5-120-IESCOMMON-MIB

Category: Domain: DSL/xPON, Vendor: Calix

Description: Common IES management objects for the Calix E5-120 integrated Ethernet service platform shared across E5-120 MIB modules.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is E5-120-IESCOMMON-MIB?

E5-120-IESCOMMON-MIB is a Calix module supporting the E5-120 integrated Ethernet service (IES) platform, defining common object and textual-convention definitions that are shared across the various E5-120 product-specific MIB modules rather than being a standalone data source. Its general purpose is to hold shared enumerations, statuses, and structural definitions (such as common alarm severities or service states) used consistently by other E5-120 MIBs. In that sense it supports monitoring of hardware and software status indirectly, by standardizing how card, port, and service status values are represented across the platform's other MIBs. No module description or sample objects were supplied in the source data, so this characterization is inferred primarily from the module's name and short description. It is deployed as an internal building block wherever Calix E5-120 access platforms are managed via SNMP in FTTx/broadband access networks. Engineers can download the E5-120-IESCOMMON-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in E5-120-IESCOMMON-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Calix E5-120 integrated Ethernet service access platform

Monitoring Examples

No sample objects were provided for this module, and none can be responsibly invented. As a "common" support MIB, it most likely defines shared textual conventions and status/alarm enumerations referenced by other E5-120 MIBs rather than exposing its own distinct monitoring table.

What Can Be Monitored

shared status/alarm enumerations used by other E5-120 MIB modules

Imported Objects

From E5-120-MIB

e5x120	OBJECT-IDENTITY
iesSeriesCommon	OBJECT-IDENTITY

From Q-BRIDGE-MIB

PortList

From RFC1155-SMI

enterprises

From RFC1213-MIB

DisplayString
PhysAddress
ifIndex

From SNMPv2-SMI

IpAddress
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
NTF reboot	1.3.6.1.4.1.6321.1.2.3.3.0.1			Send a message to the manager that the system is going to shutdown. The variable is the reason that causes the system to shutdown.
NTF systemShutdown	1.3.6.1.4.1.6321.1.2.3.3.0.2			Send a message to the manager that the system is going to shutdown. The variable is the reason that causes the system to shutdown.
NTF overheat	1.3.6.1.4.1.6321.1.2.3.3.0.3			Send a message to the manager that the system is overheated. The variable in the binding list is the current temperature in Celsius of the system.
NTF overheatOver	1.3.6.1.4.1.6321.1.2.3.3.0.4			Send a message to the manager that the overheated condition is over. The variable in the binding list is the current temperature in Celsius of the system.
NTF errLog	1.3.6.1.4.1.6321.1.2.3.3.0.5			Send a message to the manager that an error log is created in system. The variable in the binding list is the content of the error log.
NTF fanRpmLow	1.3.6.1.4.1.6321.1.2.3.3.0.6			Send a message to the manager that the rpm of the fan is too low. The variable in the binding list is the current rpm of the fan.
NTF fanRpmNormal	1.3.6.1.4.1.6321.1.2.3.3.0.7			Send a message to the manager that the low-rpm condition of the fan is over. The variable in the binding list is the current rpm of the fan.
NTF voltageOutOfRange	1.3.6.1.4.1.6321.1.2.3.3.0.8			Send a message to the manager that the voltage of the system is out of range. The variable in the binding list is the current voltage in volt of the system.
NTF voltageNormal	1.3.6.1.4.1.6321.1.2.3.3.0.9			Send a message to the manager that the low-voltage condition is over. The variable in the binding list is the current voltage in volt of the system.
NTF systemMaintenanceFailure	1.3.6.1.4.1.6321.1.2.3.3.0.10			Send a message to the manager that the system maintence operation fail. The variable in the variable binding indicates the problem.
NTF configChange	1.3.6.1.4.1.6321.1.2.3.3.0.11			This notification indicates that the configuration data of one module is changed.
NTF moduleUp	1.3.6.1.4.1.6321.1.2.3.3.0.12			A moduleUp trap signifies that the sending protocol entity recognizes that one of the modules represented in the agent's configuration has come up.
NTF moduleDown	1.3.6.1.4.1.6321.1.2.3.3.0.13			A moduleDown trap signifies that the sending protocol entity recognizes a failure in one of the modules represented in the agent's configuration.
NTF modulePlugIn	1.3.6.1.4.1.6321.1.2.3.3.0.14			A modulePlugIn trap signifies that the sending protocol entity recognizes that one module is plugged into the device.
NTF modulePullOut	1.3.6.1.4.1.6321.1.2.3.3.0.15			A modulePullOut trap signifies that the sending protocol entity recognizes one module is pulled out from the device.
NTF powerDC48VAFailure	1.3.6.1.4.1.6321.1.2.3.3.0.16			The trap signifies that the power supply of DC 48V at the right side of main Chassis (front view) failed.
NTF powerDC48VANormal	1.3.6.1.4.1.6321.1.2.3.3.0.17			The trap signifies that the power supply of DC 48V at the right side of main Chassis (front view) is in normal state.
NTF powerDC48VBFailure	1.3.6.1.4.1.6321.1.2.3.3.0.18			The trap signifies that the power supply of DC 48V at the left side of main Chassis (front view) failed.
NTF powerDC48VBNormal	1.3.6.1.4.1.6321.1.2.3.3.0.19			The trap signifies that the power supply of DC 48V at the left side of main Chassis (front view) is in normal state.
NTF extAlarmInputTrigger	1.3.6.1.4.1.6321.1.2.3.3.0.20			The trap signifies that the external alarm input of MSC card is triggered.
NTF extAlarmInputRelease	1.3.6.1.4.1.6321.1.2.3.3.0.21			The trap signifies that the external alarm input of MSC card is released.
NTF thermalSensorFailure	1.3.6.1.4.1.6321.1.2.3.3.0.22			The trap signifies that the thermal sensor failed.
NTF mscSwitchOverOK	1.3.6.1.4.1.6321.1.2.3.3.0.23			The trap signifies that MSC card is switched over successfully. The value of iesSlotId is the slot ID of the current working MSC.
NTF networkTopologyChange	1.3.6.1.4.1.6321.1.2.3.3.0.24			The trap signifies the network topology is changed.
NTF adslAtucLof	1.3.6.1.4.1.6321.1.2.3.3.0.25			The trap signifies ATU-C Loss of Framing.
NTF adslAturLof	1.3.6.1.4.1.6321.1.2.3.3.0.26			The trap signifies ATU-R Loss of Framing.
NTF adslAtucLos	1.3.6.1.4.1.6321.1.2.3.3.0.27			The trap signifies ATU-C Loss of Signal.
NTF adslAturLos	1.3.6.1.4.1.6321.1.2.3.3.0.28			The trap signifies ATU-R Loss of Signal.
NTF adslAturLpr	1.3.6.1.4.1.6321.1.2.3.3.0.29			The trap signifies ATU-R Loss of Power.
NTF adslAtucLofClear	1.3.6.1.4.1.6321.1.2.3.3.0.30			The trap signifies ATU-C Loss of Framing is cleared.
NTF adslAturLofClear	1.3.6.1.4.1.6321.1.2.3.3.0.31			The trap signifies ATU-R Loss of Framing is cleared.
NTF adslAtucLosClear	1.3.6.1.4.1.6321.1.2.3.3.0.32			The trap signifies ATU-C Loss of Signal is cleared.
NTF adslAturLosClear	1.3.6.1.4.1.6321.1.2.3.3.0.33			The trap signifies ATU-R Loss of Signal is cleared.
NTF adslAturLprClear	1.3.6.1.4.1.6321.1.2.3.3.0.34			The trap signifies ATU-R Loss of Power is cleared.
iesChassis	1.3.6.1.4.1.6321.1.2.3.3.98.1
INT iesNumOfChassis	1.3.6.1.4.1.6321.1.2.3.3.98.1.1	INTEGER	read-only	The number of chassis in the IES-2000/3000 system
iesChassisTable	1.3.6.1.4.1.6321.1.2.3.3.98.1.2		not-accessible	The table which contains the chassis information in IES-2000/3000 system
iesChassisEntry	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1		not-accessible
INT iesChassisId	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1.1	INTEGER	read-only	The Chassis ID
INT iesChassisFrameNumber	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1.2	INTEGER	read-write	The Frame ID
STR iesChassisSerialNumber	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1.3	DisplayString	read-only	The Chassis Serial Number
INT iesChassisNumber	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1.4	INTEGER	read-write	The Chassis Number which is defined by the system administrator for management purpose
INT iesChassisStatus	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1.5	INTEGER	read-only	The current status of the chassis.
STR iesChassisProductPartNumber	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1.6	DisplayString	read-only	Product part number
STR iesChassisHwRevisionNumber	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1.7	DisplayString	read-only	HW revision Number
STR iesChassisCleiCode	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1.8	DisplayString	read-only	CLEI code
STR iesChassisHwVersion	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1.9	DisplayString	read-only	Hardware version
STR iesChassisMacAddress	1.3.6.1.4.1.6321.1.2.3.3.98.1.2.1.10	DisplayString	read-only	MAC address
iesSlotTable	1.3.6.1.4.1.6321.1.2.3.3.98.1.3		not-accessible	The table which contains the slot information in a chassis of IES-2000/3000 system
iesSlotEntry	1.3.6.1.4.1.6321.1.2.3.3.98.1.3.1		not-accessible
INT iesSlotId	1.3.6.1.4.1.6321.1.2.3.3.98.1.3.1.1	INTEGER	read-only	Identity of the slot
INT iesSlotModuleType	1.3.6.1.4.1.6321.1.2.3.3.98.1.3.1.2	INTEGER	read-only	Card type of the plug-in card in IES-2000/3000.
STR iesSlotModuleDescr	1.3.6.1.4.1.6321.1.2.3.3.98.1.3.1.3	DisplayString	read-only	The descriptions of the plug-in card in IES-2000/3000.
STR iesSlotModuleFWVersion	1.3.6.1.4.1.6321.1.2.3.3.98.1.3.1.4	DisplayString	read-only	The firmware version of the plug-in card in IES-2000/3000.
STR iesSlotModuleDriverVersion	1.3.6.1.4.1.6321.1.2.3.3.98.1.3.1.5	DisplayString	read-only	The DSL driver of the plug-in card in IES-2000/3000.
STR iesSlotModuleModemCodeVersion	1.3.6.1.4.1.6321.1.2.3.3.98.1.3.1.6	DisplayString	read-only	The DSL modem code version of the plug-in card in IES-2000/3000
INT iesSlotModuleStatus	1.3.6.1.4.1.6321.1.2.3.3.98.1.3.1.7	INTEGER	read-only	The module state of the plug-in card in IES-2000/3000
INT iesSlotModuleAlarmStatus	1.3.6.1.4.1.6321.1.2.3.3.98.1.3.1.8	INTEGER	read-only	This variable indicates the alarm status of the module. It is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The moduleNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 moduleNoDefect 2 moduleOverHeat 3 moduleFanRpmLow 4 moduleVoltageLow 5 moduleThermalSensorFailure 6 modulePullOut 7 powerDC48VAFailure 8 powerDC48VBFailure 9 extAlarmInputTrigger 10 moduleDown 11 mscSwitchOverOK 12 networkTopologyChange
iesMscPortConfTable	1.3.6.1.4.1.6321.1.2.3.3.98.1.4		not-accessible	The table contains port configuration information in MSC1000.
iesMscPortConfEntry	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1		not-accessible
INT iesMscPortId	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1.1	INTEGER	read-only	Identity of the extension slot in MSC1000.
INT iesMscPortType	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1.2	INTEGER	read-only	Port type of the extension slot in MSC1000.
INT iesMscPortIfIndex	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1.3	INTEGER	read-only
INT iesMscPortSpeed	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1.4	INTEGER	read-write
INT iesMscPortDuplex	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1.5	INTEGER	read-write
INT iesMscPortFlowControl	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1.6	INTEGER	read-write
INT iesMscPortDefaultVLANTagging	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1.7	INTEGER	read-write
INT iesMscPortTrunkGroupId	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1.8	INTEGER	read-only
INT iesMscPortMode	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1.9	INTEGER	read-write	The operational mode for uplink and subtending ports in MSC. Only the operational mode of subtending ports can be modified.
INT iesMscPortVLANTrunking	1.3.6.1.4.1.6321.1.2.3.3.98.1.4.1.10	INTEGER	read-write	The VLAN trunking setting for uplink and subtending ports in MSC.
iesHWMonitor	1.3.6.1.4.1.6321.1.2.3.3.98.2
iesFanRpmTable	1.3.6.1.4.1.6321.1.2.3.3.98.2.1		not-accessible	A table that contains rpm information about the fans.
iesFanRpmEntry	1.3.6.1.4.1.6321.1.2.3.3.98.2.1.1		not-accessible	A list of rpm information for each fan.
INT iesFanRpmIndex	1.3.6.1.4.1.6321.1.2.3.3.98.2.1.1.1	INTEGER	read-only	The identity of the fan.
INT iesFanRpmCurValue	1.3.6.1.4.1.6321.1.2.3.3.98.2.1.1.2	INTEGER	read-only	The current rpm of the fan.
INT iesFanRpmMaxValue	1.3.6.1.4.1.6321.1.2.3.3.98.2.1.1.3	INTEGER	read-only	The maximum rpm ever performed by the fan.
INT iesFanRpmMinValue	1.3.6.1.4.1.6321.1.2.3.3.98.2.1.1.4	INTEGER	read-only	The minimum rpm ever performed by the fan.
INT iesFanRpmLowThresh	1.3.6.1.4.1.6321.1.2.3.3.98.2.1.1.5	INTEGER	read-only	The low threshold of the rpm of the fan. If the current rpm is less than the threshold, the device will initiate the fanRpmLow trap.
STR iesFanRpmDescr	1.3.6.1.4.1.6321.1.2.3.3.98.2.1.1.6	DisplayString	read-only	The description of the fan (e.g. location, function, etc.).
iesVoltageTable	1.3.6.1.4.1.6321.1.2.3.3.98.2.2		not-accessible	A table that contains voltage information about the system.
iesVoltageEntry	1.3.6.1.4.1.6321.1.2.3.3.98.2.2.1		not-accessible	A list of voltage information for each sensor.
INT iesVoltageIndex	1.3.6.1.4.1.6321.1.2.3.3.98.2.2.1.1	INTEGER	read-only	The identity of the sensor.
INT iesVoltageCurValue	1.3.6.1.4.1.6321.1.2.3.3.98.2.2.1.2	INTEGER	read-only	The current voltage detected by the sensor (in milli-voltage).
INT iesVoltageMaxValue	1.3.6.1.4.1.6321.1.2.3.3.98.2.2.1.3	INTEGER	read-only	The maximum voltage ever detected by the sensor (in milli-voltage).
INT iesVoltageMinValue	1.3.6.1.4.1.6321.1.2.3.3.98.2.2.1.4	INTEGER	read-only	The minimum voltage ever detected by the sensor (in milli-voltage).
INT iesVoltageNominalValue	1.3.6.1.4.1.6321.1.2.3.3.98.2.2.1.5	INTEGER	read-only	The nominal voltage which the power should supply (in milli-voltage).
INT iesVoltageLowThresh	1.3.6.1.4.1.6321.1.2.3.3.98.2.2.1.6	INTEGER	read-only	The low threshold of the voltage (in milli-voltage). If the current voltage is less than the threshold, the device will initiate the voltageLow trap.
STR iesVoltageDescr	1.3.6.1.4.1.6321.1.2.3.3.98.2.2.1.7	DisplayString	read-only	The description of the voltage (e.g. location, nominal value, etc.).
iesSysTempTable	1.3.6.1.4.1.6321.1.2.3.3.98.2.3		not-accessible	A table that contains temperature information about system.
iesSysTempEntry	1.3.6.1.4.1.6321.1.2.3.3.98.2.3.1		not-accessible	A list of temperature information for each sensor.
INT iesSysTempIndex	1.3.6.1.4.1.6321.1.2.3.3.98.2.3.1.1	INTEGER	read-only	The identity of the sensor.
INT iesSysTempCurValue	1.3.6.1.4.1.6321.1.2.3.3.98.2.3.1.2	INTEGER	read-only	The current temperature detected in Celsius by the sensor.
INT iesSysTempMaxValue	1.3.6.1.4.1.6321.1.2.3.3.98.2.3.1.3	INTEGER	read-only	The maximum temperature ever detected in Celsius by the sensor.
INT iesSysTempMinValue	1.3.6.1.4.1.6321.1.2.3.3.98.2.3.1.4	INTEGER	read-only	The minimum temperature ever detected in Celsius by the sensor.
INT iesSysTempHighThresh	1.3.6.1.4.1.6321.1.2.3.3.98.2.3.1.5	INTEGER	read-only	The high threshold of the temperature in Celsius. If the current temperature is higher than the threshold, the device will initiate the overheat trap.
STR iesSysTempDescr	1.3.6.1.4.1.6321.1.2.3.3.98.2.3.1.6	DisplayString	read-only	The description of the temperature sensor (e.g. location, function, etc.).
iesSysMgnt	1.3.6.1.4.1.6321.1.2.3.3.98.3
iesSysState	1.3.6.1.4.1.6321.1.2.3.3.98.3.1
INT iesSystemCurrentStatus	1.3.6.1.4.1.6321.1.2.3.3.98.3.1.1	INTEGER	read-only	This variable indicates the status of the system. The sysCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sysNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sysNoDefect 2 sysOverHeat 3 sysFanRpmLow 4 sysVoltageLow 5 sysThermalSensorFailure 6 modulePullOut 7 powerDC48VAFailure 8 powerDC48VBFailure 9 extAlarmInputTrigger 10 moduleDown 11 mscSwitchOverOK 12 networkTopologyChange
STR iesProblemCause	1.3.6.1.4.1.6321.1.2.3.3.98.3.1.2	DisplayString	read-only	It describes the problem occurred in the system, e.g. maintenance operation failures, system reboot, error log, ...etc.
iesSysMaintenance	1.3.6.1.4.1.6321.1.2.3.3.98.3.2
INT iesMaintenanceOps	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.1	INTEGER	read-write	The managed object is for system maintenance. When the EMS wants to trigger the system maitenance operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: config save BIT 2: reset BIT 3: local loopback test BIT 4: remote loopback test BIT 5: clear system alarms BIT 6: F4 loopback test BIT 7: F5 loopback test BIT 8: DSL Line Diagnostic
INT iesMaintenanceTarget	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.2	INTEGER	read-write	The managed object is used for identify the target on which the maintenance operation should be performed.
INT iesMaintenanceDSLConfOps	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.3	INTEGER	read-write	The managed object is for xDSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: set DSL mode BIT 4: set profile BIT 5: enable mac filter BIT 6: disable mac filter BIT 7: set packet filter BIT 8: enable dot1x BIT 9: disable dot1x BIT 10: set dot1x control BIT 11: enable dot1x re-authentication BIT 12: disable dot1x re-authentication BIT 13: set dot1x re-authentication period BIT 14: enable mac count filter BIT 15: disable mac count filter BIT 16: set mac count filter BIT 17: set alarm profile BIT 18: set Annex L (Only in AnnexA) BIT 19: set power management BIT 20: set rate adaptation mode BIT 21: set IGMP filter BIT 22: enable Annex M BIT 23: disable Annex M
OCT iesMaintenanceDSLConfTarget	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.4	OCTET STRING	read-write	The managed object is used for identify the target on which the line configuration should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11: each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
STR iesMaintenanceDSLConfProfileName	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.5	DisplayString	read-write	The DSL profile name
INT iesMaintenanceDSLConfMode	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.6	INTEGER	read-write	The DSL mode. The semantic for each bit is: Bit 1: ADSL, G.lite Bit 2: ADSL, G.dmt Bit 3: ADSL, T1.413 Bit 4: ADSL, Auto Bit 5: ADSL, ETSI Bit 6: ADSL2, Bit 7: ADSL2+
INT iesMaintenanceDSLConfPktFilter	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.7	INTEGER	read-write	The packet filter. The semantic for each bit is: Bit 1: accept all Bit 2: accept PPPoE only Bit 3: reject ARP Bit 4: reject DHCP Bit 5: reject EAPOL Bit 6: reject PPPoE Bit 7: reject NetBIOS Bit 8: reject IGMP Bit 9: reject IP
INT iesMaintenanceDSLConfDot1xControl	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.8	INTEGER	read-write	The configuration defines the 802.1x control type.
INT iesMaintenanceDSLConfDot1xReauthPeriod	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.9	INTEGER	read-write	The configuration defines the 802.1x re-authentication period (seconds).
INT iesMaintenanceDSLConfMacCount	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.10	INTEGER	read-write	The configuration defines the number of mac addresses which can pass through the port.
INT iesMaintenanceVpi	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.11	INTEGER	read-write	VPI of the channel
INT iesMaintenanceVci	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.12	INTEGER	read-write	VCI of the channel
OCT iesMaintenanceDSLConfAlarmProfileName	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.13	OCTET STRING	read-write	The DSL alarm profile name
INT iesMaintenanceDSLConfAnnexL	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.14	INTEGER	read-write	The annex L setting of the ADSL line (Only in AnnexA).
INT iesMaintenanceDSLConfPmMode	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.15	INTEGER	read-write	The power management mode of the ADSL line.
INT iesMaintenanceDSLConfRateMode	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.16	INTEGER	read-write	Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information.
OCT iesMaintenanceDSLConfIgmpFilter	1.3.6.1.4.1.6321.1.2.3.3.98.3.2.17	OCTET STRING	read-write	The IGMP filter name.
iesSysTimeSetup	1.3.6.1.4.1.6321.1.2.3.3.98.3.3
INT iesTimeServerMode	1.3.6.1.4.1.6321.1.2.3.3.98.3.3.1	INTEGER	read-write	The mechanism of Time Server when the system boots up.
IP iesTimeServerIP	1.3.6.1.4.1.6321.1.2.3.3.98.3.3.2	IpAddress	read-write	The IP Address of Time Server
STR iesSystemTime	1.3.6.1.4.1.6321.1.2.3.3.98.3.3.3	DisplayString	read-write	The system time
STR iesSystemDate	1.3.6.1.4.1.6321.1.2.3.3.98.3.3.4	DisplayString	read-write	The system date
INT iesSystemTimeZone	1.3.6.1.4.1.6321.1.2.3.3.98.3.3.5	INTEGER	read-write	The system time zone
iesSysAccessControl	1.3.6.1.4.1.6321.1.2.3.3.98.3.4
iesAccessCtrlTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.1		not-accessible	A table that contains information about service access control.
iesAccessCtrlEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.1.1		not-accessible	A list of access control entry.
INT iesAccessCtrlService	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.1.1.1	INTEGER	read-only	The service type of the access control entry.
INT iesAccessCtrlEnable	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.1.1.2	INTEGER	read-write	Enable or disable the service.
INT iesAccessCtrlPort	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.1.1.3	INTEGER	read-write	The port number which the service uses.
INT iesMaxNumOfSecuredClients	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.2	INTEGER	read-only	The maximum number of sets of secured clients.
iesSecuredClientTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.3		not-accessible	A table that contains information about secured clients.
iesSecuredClientEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.3.1		not-accessible	A list of secured client entry.
IP iesSecuredClientStartIp	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.3.1.1	IpAddress	read-only	The starting IP address of a set of secured clients.
IP iesSecuredClientEndIp	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.3.1.2	IpAddress	read-only	The ending IP address of a set of secured clients.
INT iesSecuredClientService	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.3.1.3	INTEGER	read-create	Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1: telnet BIT 2: FTP BIT 3: web BIT 4: ICMP
ROW iesSecuredClientRowStatus	1.3.6.1.4.1.6321.1.2.3.3.98.3.4.3.1.4	RowStatus	read-create	This object is used to create a new row or modify or delete an existing row in this table. A row is activated by setting this object to `active', and is deactivated by setting it to 'notInService'.
iesSysStaticRoute	1.3.6.1.4.1.6321.1.2.3.3.98.3.5
INT iesMaxNumOfStaticRoutes	1.3.6.1.4.1.6321.1.2.3.3.98.3.5.1	INTEGER	read-only	The maximum number of static routes.
iesStaticRouteTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.5.2		not-accessible	A table that contains information about static routes.
iesStaticRouteEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.5.2.1		not-accessible	A list of static route entry.
STR iesStaticRouteName	1.3.6.1.4.1.6321.1.2.3.3.98.3.5.2.1.1	DisplayString	read-only	The name of the static route.
IP iesStaticRouteDest	1.3.6.1.4.1.6321.1.2.3.3.98.3.5.2.1.2	IpAddress	read-create	The destination IP address of the static route.
IP iesStaticRouteMask	1.3.6.1.4.1.6321.1.2.3.3.98.3.5.2.1.3	IpAddress	read-create	The subnet mask of the static route.
IP iesStaticRouteGateway	1.3.6.1.4.1.6321.1.2.3.3.98.3.5.2.1.4	IpAddress	read-create	The gateway IP address of the static route.
INT iesStaticRouteMetric	1.3.6.1.4.1.6321.1.2.3.3.98.3.5.2.1.5	INTEGER	read-create	The routing metric of the static route.
ROW iesStaticRouteRowStatus	1.3.6.1.4.1.6321.1.2.3.3.98.3.5.2.1.6	RowStatus	read-create	This object is used to create a new row or modify or delete an existing row in this table. A row is activated by setting this object to `active', and is deactivated by setting it to 'notInService'.
iesSyslogSetup	1.3.6.1.4.1.6321.1.2.3.3.98.3.6
INT iesSysLogEnable	1.3.6.1.4.1.6321.1.2.3.3.98.3.6.1	INTEGER	read-write	Enable/disable syslog function.
IP iesSysLogServer	1.3.6.1.4.1.6321.1.2.3.3.98.3.6.2	IpAddress	read-write	IP address of the syslog server.
INT iesSysLogFacility	1.3.6.1.4.1.6321.1.2.3.3.98.3.6.3	INTEGER	read-write	Log facility used by the syslog function.
iesSysDhcpSetup	1.3.6.1.4.1.6321.1.2.3.3.98.3.7
INT iesDhcpRelayEnable	1.3.6.1.4.1.6321.1.2.3.3.98.3.7.1	INTEGER	read-write	Enable/disable DHCP relay function.
INT iesDhcpRelayOption82Enable	1.3.6.1.4.1.6321.1.2.3.3.98.3.7.2	INTEGER	read-write	Enable/disable DHCP relay Option82 function.
STR iesDhcpRelayOption82Info	1.3.6.1.4.1.6321.1.2.3.3.98.3.7.3	DisplayString	read-write	User specific Option82 information.
INT iesMaxNumOfDhcpServers	1.3.6.1.4.1.6321.1.2.3.3.98.3.7.4	INTEGER	read-only	The maximum number of DHCP servers.
iesDhcpServerTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.7.5		not-accessible	A table that contains DHCP server information.
iesDhcpServerEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.7.5.1		not-accessible	The entry of DHCP server table.
IP iesDhcpServerIp	1.3.6.1.4.1.6321.1.2.3.3.98.3.7.5.1.1	IpAddress	read-only	The IP address of the DHCP server.
ROW iesDhcpServerRowStatus	1.3.6.1.4.1.6321.1.2.3.3.98.3.7.5.1.2	RowStatus	read-create	The row status of the DHCP server entry.
iesSysSNMPSetup	1.3.6.1.4.1.6321.1.2.3.3.98.3.8
INT iesMaxNumberOfTrapDestinations	1.3.6.1.4.1.6321.1.2.3.3.98.3.8.1	INTEGER	read-only	The max number of the trap destinations.
iesSNMPTrapDestTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.8.2		not-accessible	A table that contains SNMP trap destination information.
iesSNMPTrapDestEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.8.2.1		not-accessible	The entry of SNMP trap destination table.
IP iesTrapDestIp	1.3.6.1.4.1.6321.1.2.3.3.98.3.8.2.1.1	IpAddress	read-only	The IP address of the trap destination.
INT iesTrapDestPort	1.3.6.1.4.1.6321.1.2.3.3.98.3.8.2.1.2	INTEGER	read-only	The UDP port of the trap destination.
ROW iesTrapDestRowStatus	1.3.6.1.4.1.6321.1.2.3.3.98.3.8.2.1.3	RowStatus	read-create	The row status of the trap destination entry.
STR iesSnmpGetCommunity	1.3.6.1.4.1.6321.1.2.3.3.98.3.8.3	DisplayString	read-write	The SNMP get community.
STR iesSnmpSetCommunity	1.3.6.1.4.1.6321.1.2.3.3.98.3.8.4	DisplayString	read-write	The SNMP set community.
STR iesSnmpTrapCommunity	1.3.6.1.4.1.6321.1.2.3.3.98.3.8.5	DisplayString	read-write	The SNMP trap community.
iesSysDot1xSetup	1.3.6.1.4.1.6321.1.2.3.3.98.3.9
INT iesMaxNumberOfRadiusServers	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.1	INTEGER	read-only	The max number of the RADIUS Servers.
iesRadiusServerTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.2		not-accessible	A table that contains Radius Server information.
iesRadiusServerEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.2.1		not-accessible	The entry of Radius Server table.
INT iesRadiusServerIndex	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.2.1.1	INTEGER	read-only	The identity of the RADIUS server.
IP iesRadiusServerIp	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.2.1.2	IpAddress	read-create	The IP address of the Radius Server.
INT iesRadiusServerPort	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.2.1.3	INTEGER	read-create	The UDP port of the Radius Server.
STR iesRadiusSharedSecret	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.2.1.4	DisplayString	read-create	The shared secret of the Radius Server.
ROW iesRadiusServerRowStatus	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.2.1.5	RowStatus	read-create	The row status of the Radius Server entry.
INT iesDot1xEnable	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.3	INTEGER	read-write	Enable/disable the 802.1x function.
iesDot1xPortTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.4		not-accessible	This table includes the configuration of 802.1x.
iesDot1xPortEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.4.1		not-accessible	An entry in iesDot1xPortTable.
INT iesDot1xPortEnable	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.4.1.1	INTEGER	read-write	The option defines if the port enables 802.1x settings.
INT iesDot1xPortControl	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.4.1.2	INTEGER	read-write	The configuration defines the 802.1x port control type.
INT iesDot1xPortReAuthEnable	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.4.1.3	INTEGER	read-write	The option defines if the port enables 802.1x re-authentication.
INT iesDot1xPortReAuthPeriod	1.3.6.1.4.1.6321.1.2.3.3.98.3.9.4.1.4	INTEGER	read-write	The configuration defines the 802.1x re-authentication period (seconds) for each port.
iesSysMacFilter	1.3.6.1.4.1.6321.1.2.3.3.98.3.10
iesMacFilterStatusTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.10.1		not-accessible	This table includes the status of mac filtering for each port.
iesMacFilterStatusEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.10.1.1		not-accessible	An entry in iesMacFilterStatusTable.
INT iesMacFilterStatusEnable	1.3.6.1.4.1.6321.1.2.3.3.98.3.10.1.1.1	INTEGER	read-write	The option defines if the port enables mac filtering.
INT iesMaxNumberOfMacFilters	1.3.6.1.4.1.6321.1.2.3.3.98.3.10.2	INTEGER	read-only	The max number of the mac filters in the system.
INT iesMaxNumberOfMacFiltersPerPort	1.3.6.1.4.1.6321.1.2.3.3.98.3.10.3	INTEGER	read-only	The max number of the mac filters for each port.
INT iesCurrNumberOfMacFilters	1.3.6.1.4.1.6321.1.2.3.3.98.3.10.4	INTEGER	read-only	The current number of the mac filters in the system.
iesMacFilterTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.10.5		not-accessible	A table that contains the mac filtering information.
iesMacFilterEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.10.5.1		not-accessible	The entry of iesMacFilterTable.
PHY iesMacFilterMacAddr	1.3.6.1.4.1.6321.1.2.3.3.98.3.10.5.1.1	PhysAddress	read-only	The mac address which can pass through the port.
ROW iesMacFilterRowStatus	1.3.6.1.4.1.6321.1.2.3.3.98.3.10.5.1.2	RowStatus	read-create	The row status of the entry.
iesSysPacketFilter	1.3.6.1.4.1.6321.1.2.3.3.98.3.11
iesPacketFilterTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.11.1		not-accessible	This table includes packet filtering for each port.
iesPacketFilterEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.11.1.1		not-accessible	An entry in iesPacketFilterTable.
INT iesPacketFilter	1.3.6.1.4.1.6321.1.2.3.3.98.3.11.1.1.1	INTEGER	read-write	The packet filter. The semantic for each bit is: Bit 1: accept all Bit 2: accept PPPoE only Bit 3: reject ARP Bit 4: reject DHCP Bit 5: reject EAPOL Bit 6: reject PPPoE Bit 7: reject NetBIOS Bit 8: reject IGMP Bit 9: reject IP
iesSysMacCountFilter	1.3.6.1.4.1.6321.1.2.3.3.98.3.12
iesMacCountFilterTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.12.1		not-accessible	This table includes mac count filtering for each port.
iesMacCountFilterEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.12.1.1		not-accessible	An entry in iesMacCountFilterTable.
INT iesMacCountFilterStatus	1.3.6.1.4.1.6321.1.2.3.3.98.3.12.1.1.1	INTEGER	read-write	The option defines if the port enables mac count filtering.
INT iesMacCountFilterCount	1.3.6.1.4.1.6321.1.2.3.3.98.3.12.1.1.2	INTEGER	read-write	The number of mac addresses which can pass through the port.
iesSysMulticastGroup	1.3.6.1.4.1.6321.1.2.3.3.98.3.13
INT iesMaxNumberOfMulticastGroups	1.3.6.1.4.1.6321.1.2.3.3.98.3.13.1	INTEGER	read-only	The max number of static multicast groups in the system.
iesMulticastGroupTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.13.2		not-accessible	A table that contains static multicast group information.
iesMulticastGroupEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.13.2.1		not-accessible	The entry of multicast group table.
INT iesMulticastGroupVid	1.3.6.1.4.1.6321.1.2.3.3.98.3.13.2.1.1	INTEGER	read-only	The multicast VLAN of the group.
PHY iesMulticastGroupMacAddr	1.3.6.1.4.1.6321.1.2.3.3.98.3.13.2.1.2	PhysAddress	read-only	The multicast MAC address of the group.
POR iesMulticastGroupPorts	1.3.6.1.4.1.6321.1.2.3.3.98.3.13.2.1.3	PortList	read-create	The port list which specifies the ports joining the multicast group.
ROW iesMulticastGroupRowStatus	1.3.6.1.4.1.6321.1.2.3.3.98.3.13.2.1.4	RowStatus	read-create	The row status of the multicast group entry.
iesSysIgmpFilter	1.3.6.1.4.1.6321.1.2.3.3.98.3.14
INT iesMaxNumberOfIgmpFilters	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.1	INTEGER	read-only	The max number of IGMP filters in the system.
iesIgmpFilterTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.2		not-accessible	A table that contains IGMP filters.
iesIgmpFilterEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.2.1		not-accessible	The entry of IGMP filter table.
OCT iesIgmpFilterName	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.2.1.1	OCTET STRING	read-only	The IGMP filter name.
INT iesIgmpFilterIndex	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.2.1.2	INTEGER	read-only	The index which specifies the filter rule.
IP iesIgmpFilterStartIp	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.2.1.3	IpAddress	read-create	The start IP of the filter rule.
IP iesIgmpFilterEndIp	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.2.1.4	IpAddress	read-create	The end IP of the filter rule.
ROW iesIgmpFilterRowStatus	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.2.1.5	RowStatus	read-create	The row status of the IGMP filter entry.
iesIgmpFilterPortTable	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.3		not-accessible	This table specifies the IGMP filter of the port.
iesIgmpFilterPortEntry	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.3.1		not-accessible	An entry in iesIgmpFilterPortTable.
OCT iesIgmpFilterPortFilter	1.3.6.1.4.1.6321.1.2.3.3.98.3.14.3.1.1	OCTET STRING	read-write	The IGMP filter of the port.
iesL2SW	1.3.6.1.4.1.6321.1.2.3.3.98.4
INT iesIGMPSnoopingEnabled	1.3.6.1.4.1.6321.1.2.3.3.98.4.1	INTEGER	read-write	A flag indicating whether IGMP snooping function is enabled or not.
INT iesManagementVLANId	1.3.6.1.4.1.6321.1.2.3.3.98.4.2	INTEGER	read-write	The VLAN ID for management.
INT iesMaxNumOfStaticVlans	1.3.6.1.4.1.6321.1.2.3.3.98.4.3	INTEGER	read-only	The maximum number of static VLANs supported by the system.
INT iesMaxNumOfTrunkGroups	1.3.6.1.4.1.6321.1.2.3.3.98.4.4	INTEGER	read-only	The maximum number of trunk groups.
iesTrunkGroupTable	1.3.6.1.4.1.6321.1.2.3.3.98.4.5		not-accessible	A table that contains trunk group configuration.
iesTrunkGroupEntry	1.3.6.1.4.1.6321.1.2.3.3.98.4.5.1		not-accessible	The entry of trunk group table
INT iesTrunkGroupId	1.3.6.1.4.1.6321.1.2.3.3.98.4.5.1.1	INTEGER	read-only	The ID of the trunk group
STR iesTrunkGroupName	1.3.6.1.4.1.6321.1.2.3.3.98.4.5.1.2	DisplayString	read-create	The name of the trunk group
POR iesTrunkGroupPorts	1.3.6.1.4.1.6321.1.2.3.3.98.4.5.1.3	PortList	read-create	The port list of the trunk group
ROW iesTrunkGroupRowStatus	1.3.6.1.4.1.6321.1.2.3.3.98.4.5.1.4	RowStatus	read-create	The row status of the trunk group entry
INT iesPortIsolationEnable	1.3.6.1.4.1.6321.1.2.3.3.98.4.6	INTEGER	read-write	A flag indicating whether VLAN port isolation function is enabled or not.
INT iesRSTPEnable	1.3.6.1.4.1.6321.1.2.3.3.98.4.7	INTEGER	read-write	Enable/Disable RSTP.
INT iesSwitchMode	1.3.6.1.4.1.6321.1.2.3.3.98.4.8	INTEGER	read-write	Switch DSLAM's operatrion Mode.

RFC description

Management MIB for Ciena E5-120 platform common IES (Intelligent Ethernet Service) functions; defines shared management objects across E5-120 services.

Start monitoring Calix E5-120 integrated Ethernet service access platform (shared definitions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download E5-120-IESCOMMON-MIB

What Is E5-120-IESCOMMON-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description