E5-110-MIB

All MIBs › E5-110-MIB

Category: DSL and Broadband, Domain: DSL/xPON, Vendor: Calix

Description:

The main management MIB for the Calix E5-110 multi-service access platform, covering both system status and configuration.

Imported Objects

From BRIDGE-MIB

BridgeId
MacAddress
Timeout
dot1dBasePort	OBJECT-TYPE

From P-BRIDGE-MIB

dot1dTrafficClass

OBJECT-TYPE

From Q-BRIDGE-MIB

PortList
VlanIndex
dot1qVlanIndex	OBJECT-TYPE

From RFC1155-SMI

enterprises

From RFC1213-MIB

DisplayString
PhysAddress
ifIndex

From SNMPv2-SMI

Counter32
Counter64
Gauge32
IpAddress
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION

What Is E5-110-MIB?

E5-110-MIB is Calix's core management MIB for the E5-110 multi-service access platform, a compact fiber/copper access node used in FTTx and broadband access networks. It exposes system-level configuration and status data, covering chassis/system identification, service provisioning parameters, and interface-level operational state for the unit's access ports. Because no detailed object names were available for this module, its role is inferred from the short description and Calix E-series conventions, but such access-node MIBs typically surface hardware status such as system uptime, card/module presence, environmental alarms, and software/firmware version alongside faults raised via traps. It likely depends on or complements standard IETF MIBs (e.g., IF-MIB, ENTITY-MIB) as is common for Calix E-series products. It is deployed by telecom and broadband service providers managing E5-110 access nodes at the network edge or in a central office/cabinet. Service providers onboarding a new E5-110 unit into their monitoring platform will need an E5-110-MIB download to compile alongside standard IETF MIBs before polling can begin.

IPNetwork Monitor allows you to monitor SNMP objects defined in E5-110-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

system uptime
chassis/system identification
firmware/software version
service provisioning status
access port operational state
environmental/fault alarms

Supported Devices

Calix E5-110 multi-service access platform

Monitoring Examples

An operator would poll system-level status objects on the E5-110 to confirm the unit is online and check firmware version consistency across a fleet of deployed nodes. Interface and service tables (following the platform's standard naming pattern) would be checked to spot ports that have dropped out of service or exceeded error thresholds. Because explicit object names weren't captured for this MIB, exact polling targets would need to be confirmed against the compiled MIB source.

OIDs

OID symbolic	OID numeric	Type	Access	Description
accessCtrl	1.3.6.1.4.1.6321.1.2.3.1.11.5
accessSwitchCommonATM	1.3.6.1.4.1.6321.1.2.3.1.99
acl	1.3.6.1.4.1.6321.1.2.3.1.10.56
INT aclProfileActionNumber	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.3	INTEGER	read-write	Profile action number. Bit 1: rate Bit 2: rvlan Bit 3: rpri Bit 4: deny Bit 1, Bit 2 & Bit 3 can multiple selection.
INT aclProfileActionRate	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.21	INTEGER	read-write	Profile action to replace to this rate
INT aclProfileActionrpri	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.23	INTEGER	read-write	Profile action to replace to this priority
INT aclProfileActionrvlan	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.22	INTEGER	read-write	Profile action to replace to this vlan
aclProfileEntry	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1		not-accessible	An entry of aclProfileTable.
ROW aclProfileRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.24	RowStatus	read-write	The row status of the entry.
INT aclProfileRuleDestEndPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.20	INTEGER	read-write	Profile rule destination end port
IP aclProfileRuleDestIP	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.13	IpAddress	read-write	Profile rule source IP
INT aclProfileRuleDestIPMask	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.14	INTEGER	read-write	The subnet mask of dest IP mask
INT aclProfileRuleDestStartPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.19	INTEGER	read-write	Profile rule destination start port
PHY aclProfileRuleDmac	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.8	PhysAddress	read-write	Profile rule destination MAC
INT aclProfileRuleEndTos	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.16	INTEGER	read-write	Profile rule end type of service
INT aclProfileRuleEtype	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.5	INTEGER	read-write	Profile rule etype
STR aclProfileRuleName	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.1	DisplayString	read-only	Profile rule name
INT aclProfileRuleNumber	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.2	INTEGER	read-write	The managed object is for acl profile rule configuration. etype vlan (1), etype smac (2), etype dmac (3), vlan smac (4), vlan dmac (5), smac dmac (6), vlan priority (7), etype (8), vlan (9), smac (10), dmac (11), priority (12), protocol (13), {srcip /{\|dstip /{\|tos {\|srcport {\|dstport }}}}} (14)
INT aclProfileRuleParamMask	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.4	INTEGER	read-write	Profile rule parameter mask. BIT 1: srcip / BIT 2: dstip / BIT 3: tos BIT 4: srcport BIT 5: dstport
INT aclProfileRulePriority	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.9	INTEGER	read-write	Profile rule priority
INT aclProfileRuleProtocol	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.10	INTEGER	read-write	Profile rule protocol. icmp(1),igmp(2),ip(4),tcp(6), udp(17),gre(47),ospf(89), other ptype
PHY aclProfileRuleSmac	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.7	PhysAddress	read-write	Profile rule source MAC
INT aclProfileRuleSrcEndPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.18	INTEGER	read-write	Profile rule source end port
IP aclProfileRuleSrcIP	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.11	IpAddress	read-write	Profile rule source IP
INT aclProfileRuleSrcIPMask	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.12	INTEGER	read-write	The subnet mask of source IP mask
INT aclProfileRuleSrcStartPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.17	INTEGER	read-write	Profile rule source start port
INT aclProfileRuleStartTos	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.15	INTEGER	read-write	Profile rule start type of service
INT aclProfileRuleVid	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.6	INTEGER	read-write	Profile rule vid
aclProfileTable	1.3.6.1.4.1.6321.1.2.3.1.10.56.2		not-accessible	aclProfileTable.
aclSetEntry	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1		not-accessible	An entry of aclSetTable.
STR aclSetProfileName	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.3	DisplayString	read-only	ACL Profile name
ROW aclSetRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.4	RowStatus	read-write	RowStatus of aclSetEntry
aclSetTable	1.3.6.1.4.1.6321.1.2.3.1.10.56.1		not-accessible	aclsetTable.
INT aclSetVci	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.2	INTEGER	read-only	VCI value
INT aclSetVpi	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.1	INTEGER	read-only	VPI value
STR adslAlarmProfileForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.6	DisplayString	read-write	The ADSL alarm profile.
OCT adslAtucCarrierMask0ForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.12	OCTET STRING	read-write	The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates the bin is masked off.
OCT adslAtucCarrierMask1ForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.13	OCTET STRING	read-write	The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
INT adslAtucInpForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.15	INTEGER	read-write	The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslAtucMaxTxPowerForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.9	INTEGER	read-write	The maximum allowed transmit power of ATU-C.
OCT adslAturCarrierMaskForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.11	OCTET STRING	read-write	The upstream carrier mask.For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off.
INT adslAturInpForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.14	INTEGER	read-write	The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslAturMaxTxPowerForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.8	INTEGER	read-write	The maximum allowed transmit power of ATU-R.
INT adslL0TimeForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.16	INTEGER	read-write	Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslL0toL2RateForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.22	INTEGER	read-write	configured transition L0 to L2 rate. (= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
INT adslL2ATPRForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.18	INTEGER	read-write	Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslL2ATPRTForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.19	INTEGER	read-write	the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslL2TimeForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.17	INTEGER	read-write	Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslLineConfAdslMode	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.1	INTEGER	read-write	G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
INT adslLineConfAnnexI	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.4	INTEGER	read-write	Enable/disable annex I for the port(For BCM AnnexA solution).
INT adslLineConfAnnexL	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.2	INTEGER	read-write	Enable/disable annex L for the port(Only in AnnexA).
INT adslLineConfAnnexM	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.3	INTEGER	read-write	Enable/disable annex M for the port(For BCM AnnexA solution).
OCT adslLineConfAtucCarrierMask0	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.12	OCTET STRING	read-write	The downstream carrier mask. For CTLM AnnexA solution, bin is from 32 to 255; CTLM AnnexB solution, bin is from 64 to 255; BCM solution, bin is from 32 to 255. Bit set to 1 indicates the bin is masked off.
OCT adslLineConfAtucCarrierMask1	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.13	OCTET STRING	read-write	The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
INT adslLineConfAtucInp	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.15	INTEGER	read-write	The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslLineConfAtucMaxTxPower	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.9	INTEGER	read-write	The maximum allowed transmit power of ATU-C.
OCT adslLineConfAturCarrierMask	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.11	OCTET STRING	read-write	The upstream carrier mask. For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off.
INT adslLineConfAturInp	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.14	INTEGER	read-write	The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslLineConfAturMaxTxPower	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.8	INTEGER	read-write	The maximum allowed transmit power of ATU-R.
INT adslLineConfDSPhyr	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.25	INTEGER	read-write	Enable/disable Downstream PHYR for the port(For BCM solution).
adslLineConfEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1		not-accessible	An entry in adslLineConfTable.
INT adslLineConfL0Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.16	INTEGER	read-write	Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslLineConfL0toL2Rate	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.22	INTEGER	read-write	configured transition L0 to L2 rate. (= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
INT adslLineConfL2ATPR	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.18	INTEGER	read-write	Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslLineConfL2ATPRT	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.19	INTEGER	read-write	the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslLineConfL2Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.17	INTEGER	read-write	Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslLineConfMaxL2Rate	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.20	INTEGER	read-write	configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
INT adslLineConfMaxRxPower	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.10	INTEGER	read-write	The maximum aggregate received power.
INT adslLineConfMinL2Rate	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.21	INTEGER	read-write	configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
INT adslLineConfNitro	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.23	INTEGER	read-write	Enable/disable nitro mode for the port(For BCM solution).
INT adslLineConfOptionMask	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.5	INTEGER	read-write	The semantic for each bit is: BIT 1 : Disable Trellis BIT 2 : Disable Reed-Solomon BIT 3 : Disable upstream bitswap BIT 4 : Disable downstream bitswap BIT 5 : Disable 1-bit constellation BIT 6 : Disable transmit windowing BIT 7 : Disable s=0.5 support (ADSL1 only) BIT 8 : Disable G.lite rate limit (ADSL1 only) BIT 9 : Enable Nitro BIT 10: Enable US PHYR BIT 11: ENABLE DS PHYR
INT adslLineConfPowerMgmt	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.6	INTEGER	read-write	Enable/disable power management for the port.
INT adslLineConfPowerMode	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.7	INTEGER	read-write	The power mode of the ADSL line.
adslLineConfTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.1		not-accessible	This table includes common attributes describing the ADSL line.
INT adslLineConfUSPhyr	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.24	INTEGER	read-write	Enable/disable Upstream PHYR for the port(For BCM solution).
STR adslLineProfileForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.5	DisplayString	read-write	The ADSL line profile.
adslLineStatusEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1		not-accessible	An entry in adslLineStatusTable.
INT adslLineStatusMode	1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.1	INTEGER	read-only	The link up mode of the ADSL line.
adslLineStatusTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.4		not-accessible	This table includes the ADSL line status.
INT adslLineUpTime	1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.2	INTEGER	read-only	The link up time of the ADSL line, in unit of seconds
INT adslMaxL2RateForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.20	INTEGER	read-write	configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
INT adslMaxRxPowerForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.10	INTEGER	read-write	The maximum aggregate received power.
INT adslMinL2RateForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.21	INTEGER	read-write	configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
INT adslModeForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.4	INTEGER	read-write	G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
INT adslOptionMaskForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.7	INTEGER	read-write	The semantic for each bit is identical to the object adslLineConfOptionMask.
adslPort	1.3.6.1.4.1.6321.1.2.3.1.8.2
adslPortBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3
INT adslPortOps	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.2	INTEGER	read-write	The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: set ADSL mode BIT 4: set line profile BIT 5: set alarm profile BIT 6: enable Annex L to be narrow mode(Only in AnnexA) BIT 7: enable Annex L to be wide mode(Only in AnnexA) BIT 8: disable Annex L(Only in AnnexA) BIT 9: enable Annex M (For BCM AnnexA solution) BIT 10: disable Annex M (For BCM AnnexA solution) BIT 11: enable Annex I (For BCM AnnexA solution) BIT 12: disable Annex I (For BCM AnnexA solution) BIT 13: set option mask BIT 14: enable power management mode to be L2 BIT 15: enable power management mode to be L2 BIT 16: disable power management mode BIT 17: set power mode to be fixed BIT 18: set power mode to be priority to power BIT 19: set power mode to be priority to rate BIT 20: set ATU-R max Tx power BIT 21: set ATU-C max Tx power BIT 22: set max Rx power BIT 23: set ATU-R carrier mask BIT 24: set ATU-C carrier mask BIT 25: set ATU-R INP minimum setting BIT 26: set ATU-C INP minimum setting
INT adslPortOps2	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.3	INTEGER	read-write	The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: set L0 Time BIT 2: set L2 Time BIT 3: set L2 ATPR BIT 4: set L2 ATPRT BIT 5: set maximum L2 rate BIT 6: set minimum L2 rate BIT 7: set transition L0 to L2 rate
OCT adslPortTarget	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.1	OCTET STRING	read-write	The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chaises) Byte 2~3: 0,0 Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
adslPortUtilEntry	1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1		not-accessible	An entry in adslPortUtilEntry.
INT adslPortUtilRx	1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.2	INTEGER	read-only	Measure adsl port's rx utilization.
adslPortUtilTable	1.3.6.1.4.1.6321.1.2.3.1.13.18.1		not-accessible	This table includes adsl port utilization.
INT adslPortUtilTx	1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.1	INTEGER	read-only	Measure adsl port's tx utilization.
adslStats	1.3.6.1.4.1.6321.1.2.3.1.13.18
aesSeriesCommon	1.3.6.1.4.1.6321.1.2.3.1.97
alarmconf	1.3.6.1.4.1.6321.1.2.3.1.2
INT alarmConfClearable	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.5	INTEGER	read-write	Setting the object to one indicates that the alarm is to be cleared when user submits alarm clear.
alarmConfEntry	1.3.6.1.4.1.6321.1.2.3.1.2.2.1		not-accessible	An entry in alarmConfTable.
INT alarmConfFacility	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.2	INTEGER	read-write	Alarm facility.
INT alarmConfId	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.1	INTEGER	read-only	5000:adslLine_up 5001:adslLine_down 5002:adslPerf_lol_thresh 5003:adslPerf_lof_thresh 5004:adslPerf_los_thresh 5005:adslPerf_lop_thresh 5006:adslPerf_es_thresh 5007:adslPerf_ses_thresh 5008:adslPerf_uas_thresh 5009:adslAtuc_loftrap 5010:adslAtuc_lostrap 5011:adslAtur_loftrap 5012:adslAtur_lostrap 5013:adslAtur_lprtrap 5014:ad_dhcp_rt_full 5015:ad_dhcp_dm_conflict 5016:ad_dhcp_entry_full 5017:ad_dhcp_ip_dup 5018:ad_dhcp_mac_dup 10000:eqptVol_err 10001:eqptEqpttemp_err 10002:eqptFan_err 10003:eqptHw_rtc_fail 10004:eqptHw_mon_fail 10005:eqptCold_start 10006:eqptWarm_start 10007:eqptAlm_input 10008:eqptI2c_err 10009:eqptAlm_input2 10010:eqptAlm_input3 15000:sysReboot 15001:sysAco 15002:sysAlm_clear 15003:sysLogin_fail 15004:sysAnti_spoofing 15005:sysAlm_svrty_change 20000:enetUp 20001:enetDown
INT alarmConfSeverity	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.4	INTEGER	read-write	Alarm severity
alarmConfTable	1.3.6.1.4.1.6321.1.2.3.1.2.2		not-accessible	This table includes alarm configuration.
INT alarmConfTarget	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.3	INTEGER	read-write	The destination which alarms are reported to. Set the bit to 1 to enable the target. BIT 1: snmp trap BIT 2: syslog
STR alarmCurrDescr	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.14	DisplayString	read-only	The description of the alarm.
alarmCurrEntry	1.3.6.1.4.1.6321.1.2.3.1.2.3.1		not-accessible	An entry in alarmCurrTable.
INT alarmCurrIndex	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.1	INTEGER	read-only	Index of the alarm.
TIK alarmCurrOccurTime	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.2	TimeTicks	read-only	Alarm occurence time (in hundredths of a second) since the system was last re-initialized.
INT alarmCurrParam1	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.4	INTEGER	read-only	The 1st parameter of the alarm.
INT alarmCurrParam2	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.5	INTEGER	read-only	The 2nd parameter of the alarm.
INT alarmCurrParam3	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.6	INTEGER	read-only	The 3rd parameter of the alarm.
INT alarmCurrParam4	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.7	INTEGER	read-only	The 4th parameter of the alarm.
INT alarmCurrParam5	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.8	INTEGER	read-only	The 5th parameter of the alarm.
INT alarmCurrParam6	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.9	INTEGER	read-only	The 6th parameter of the alarm.
INT alarmCurrParam7	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.10	INTEGER	read-only	The 7th parameter of the alarm.
INT alarmCurrParam8	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.11	INTEGER	read-only	The 8th parameter of the alarm.
INT alarmCurrSeverity	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.13	INTEGER	read-only	The severity of the alarm.
alarmCurrTable	1.3.6.1.4.1.6321.1.2.3.1.2.3		not-accessible	This table includes current alarm information.
STR alarmCurrTimeDescr	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.12	DisplayString	read-only	The string representation of occurence time (YYYY/MM/DD HH:MM:SS).
OID alarmCurrTrapOid	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.3	OBJECT IDENTIFIER	read-only	Trap OID of the alarm.
INT alarmOps	1.3.6.1.4.1.6321.1.2.3.1.2.1	INTEGER	read-write	The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: clear BIT 2: cutoff
alarmSeverityPortEntry	1.3.6.1.4.1.6321.1.2.3.1.2.4.1		not-accessible	An entry in alarmSeverityPortTable.
alarmSeverityPortTable	1.3.6.1.4.1.6321.1.2.3.1.2.4		not-accessible	This table includes the configuration of alarm reporting severity threshold for each port.
arpproxy	1.3.6.1.4.1.6321.1.2.3.1.8.12.8
INT arpproxyAge	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.1	INTEGER	read-write	Aging time of the ARP proxy. This object is supported by R3.00 and later versions.
INT arpproxyDhcpIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.9	INTEGER	read-only
arpproxyEntry	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1		not-accessible	An entry of arpproxyTable.
arpproxyFlush	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2
IP arpproxyFlushEdgeRouterIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.3	IpAddress	read-write	Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
VLA arpproxyFlushEdgeRouterVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.4	VlanIndex	read-write	Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
IP arpproxyFlushInterfaceIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.5	IpAddress	read-write	Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
INT arpproxyFlushInterfaceMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.6	INTEGER	read-write	Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
VLA arpproxyFlushInterfaceVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.7	VlanIndex	read-write	Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
INT arpproxyFlushOps	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.2	INTEGER	read-write	Set the object to 1 to start flushing. This object is supported by R3.00 and later versions.
INT arpproxyFlushTarget	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.1	INTEGER	read-write	The target whose ARP table to be flushed. This object is supported by R3.00 and later versions.
INT arpproxyIfIndex	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.3	INTEGER	read-only
IP arpproxyInterfaceIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.6	IpAddress	read-only
INT arpproxyInterfaceMask	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.7	INTEGER	read-only
VLA arpproxyInterfaceVid	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.8	VlanIndex	read-only
IP arpproxyIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.1	IpAddress	read-only
MAC arpproxyMac	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.2	MacAddress	read-only
arpproxyTable	1.3.6.1.4.1.6321.1.2.3.1.13.14.1		not-accessible	Display ARP table. This table is supported by R3.00 and later versions.
INT arpproxyType	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.10	INTEGER	read-only
INT arpproxyVci	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.5	INTEGER	read-only
INT arpproxyVpi	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.4	INTEGER	read-only
INT auditQryEnable	1.3.6.1.4.1.6321.1.2.3.1.7.12.1	INTEGER	read-write	Enable/disable IGMP audit query.
INT auditQryInterval	1.3.6.1.4.1.6321.1.2.3.1.7.12.2	INTEGER	read-write	Set IGMP Audit Query Interval, 1~4 in 100 milliseconds.
INT auditQryRobust	1.3.6.1.4.1.6321.1.2.3.1.7.12.3	INTEGER	read-write	Set IGMP Audit Query Robustness, 1~5.
auditQuery	1.3.6.1.4.1.6321.1.2.3.1.7.12
calixNetworks	1.3.6.1.4.1.6321
calixProducts	1.3.6.1.4.1.6321.1.2
calixRegistrations	1.3.6.1.4.1.6321.1
clear	1.3.6.1.4.1.6321.1.2.3.1.14
INT counterClearOps	1.3.6.1.4.1.6321.1.2.3.1.14.2	INTEGER	read-write	The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: clear interface counters BIT 2: clear pvc packet counters BIT 3: clear port ATM counters BIT 4: clear pvc ATM counters BIT 5: clear DHCP counters BIT 6: clear IGMP counters BIT 7: clear IGMP port counters BIT 8: clear MACFF ARP counters BIT 9: clear current lineperf BIT 10: clear current 15 minute lineperf BIT 11: clear current 1 day lineperf
OCT counterClearTarget	1.3.6.1.4.1.6321.1.2.3.1.14.1	OCTET STRING	read-write	This managed object is used for identify the target on which the counter would be cleared. The target is encoded as: Byte 1: reserved Byte 2~3: reserved Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
INT counterClearVci	1.3.6.1.4.1.6321.1.2.3.1.14.4	INTEGER	read-write	VCI of the pvc whose counters would be cleared.
INT counterClearVpi	1.3.6.1.4.1.6321.1.2.3.1.14.3	INTEGER	read-write	VPI of the pvc whose counters would be cleared.
INT currNumOfMacFiltersInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.53.4	INTEGER	read-only	The current number of mac filters in the system.
delayedReboot	1.3.6.1.4.1.6321.1.2.3.1.11.15
INT delayedRebootCancel	1.3.6.1.4.1.6321.1.2.3.1.11.15.3	INTEGER	read-write	cancel the scheduled reboot.
INT delayedRebootRemainingTime	1.3.6.1.4.1.6321.1.2.3.1.11.15.2	INTEGER	read-only	Display the remaining time of scheduled reboot.
INT delayedRebootTimer	1.3.6.1.4.1.6321.1.2.3.1.11.15.1	INTEGER	read-write	5~1800 secs, 0: reboot immediately.
dhcp	1.3.6.1.4.1.6321.1.2.3.1.10.51
C64 dhcpAck	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.4	Counter64	read-only	The total number of received DHCP IP acknowledge packets.
C64 dhcpAckBySnoopFull	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.5	Counter64	read-only	The total number of received DHCP IP acknowledge packets that replace the oldest snooping entry in snooping table due to table full.
C64 dhcpDiscovery	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.1	Counter64	read-only	The total number of received DHCP server discovery packets.
C64 dhcpOffer	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.2	Counter64	read-only	The total number of received DHCP server offer packets.
INT dhcpRelay82ActiveServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.3	INTEGER	read-only	The current active DHCP Relay server.
INT dhcpRelay82Enable	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.4	INTEGER	read-create	Enable/disable DHCP relay and Option82 function.
dhcpRelay82Entry	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1		not-accessible	The entry of DHCP Relay table.
INT dhcpRelay82EntryEnable	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.10	INTEGER	read-create	Enable/disable DHCP Relay
INT dhcpRelay82EntryOptionMode	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.11	INTEGER	read-create	Option82 format.
IP dhcpRelay82FifthServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.17	IpAddress	read-write	The IP address of the DHCP Relay fifth server.
IP dhcpRelay82FourthServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.16	IpAddress	read-write	The IP address of the DHCP Relay fourth server.
STR dhcpRelay82Info	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.5	DisplayString	read-create	User specific Option82 information.
IP dhcpRelay82PrimaryServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.1	IpAddress	read-write	The IP address of the DHCP Relay primary server.
INT dhcpRelay82RelayMode	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.6	INTEGER	read-create	DHCP relay mode.
IP dhcpRelay82SecondaryServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.2	IpAddress	read-write	The IP address of the DHCP Relay secondary server.
INT dhcpRelay82ServerVid	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.18	INTEGER	read-write	The VID of the DHCP Relay server for this VLAN.
INT dhcpRelay82Suboption2Enable	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.8	INTEGER	read-create	Enable/disable Option 82 sub-option 2.
STR dhcpRelay82Suboption2Info	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.9	DisplayString	read-create	User specified information for Option 82 sub-option 2.
dhcpRelay82Table	1.3.6.1.4.1.6321.1.2.3.1.10.51.2		not-accessible	A table that contains DHCP Relay configuration.
IP dhcpRelay82ThirdServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.15	IpAddress	read-write	The IP address of the DHCP Relay third server.
IP dhcpRelay82VlanGateway	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.14	IpAddress	read-write	The gateway of the DHCP Relay interface for this VLAN.
IP dhcpRelay82VlanIp	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.12	IpAddress	read-write	The IP address of the DHCP Relay interface for this VLAN.
INT dhcpRelay82VlanMask	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.13	INTEGER	read-write	The network mask of the DHCP Relay interface for this VLAN.
dhcpRelayArp	1.3.6.1.4.1.6321.1.2.3.1.10.51.9
INT dhcpRelayArpFlushOps	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.2	INTEGER	read-write	Set the object to 1 to start flushing.
dhcpRelayArpShowEntry	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1		not-accessible	An entry of dhcpRelayArpShowTable.
IP dhcpRelayArpShowIp	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.2	IpAddress	read-only	Display the IP of the DHCP ARP entry.
PHY dhcpRelayArpShowMac	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.3	PhysAddress	read-only	Display the MAC of the DHCP ARP entry.
dhcpRelayArpShowTable	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1		not-accessible	The table displays DHCP ARP.
INT dhcpRelayArpShowVid	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.1	INTEGER	read-only	Display the VID of the DHCP ARP entry.
dhcpRelayTest	1.3.6.1.4.1.6321.1.2.3.1.10.51.8
IP dhcpRelayTestIp	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.2	IpAddress	read-write	Setting the IP of the test server.
INT dhcpRelayTestOps	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.3	INTEGER	read-write	Set the object to 1 to test DHCP server.
STR dhcpRelayTestStatus	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.4	DisplayString	read-only	Display testing server status.
INT dhcpRelayTestVid	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.1	INTEGER	read-write	Setting the VID of the test server.
C64 dhcpRequest	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.3	Counter64	read-only	The total number of received DHCP IP request packets.
dhcpRouteEntry	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1		not-accessible	An entry of dhcpRouteTable.
IP dhcpRouteGwIP	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.5	IpAddress	read-only	The gateway IP address.
INT dhcpRouteIndex	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.1	INTEGER	read-only
IP dhcpRouteIP	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.3	IpAddress	read-only	IP of this dhcp route
INT dhcpRouteMask	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.4	INTEGER	read-only	The subnet mask of source IP mask.
dhcpRouteTable	1.3.6.1.4.1.6321.1.2.3.1.13.11.3		not-accessible	A table that contains dhcp route information.
VLA dhcpRouteVid	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.2	VlanIndex	read-only	The VLAN-ID refering to this dhcp route.
dhcpSnoop	1.3.6.1.4.1.6321.1.2.3.1.10.55
dhcpSnoopCounterEntry	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1		not-accessible	An entry of dhcpSnoopCounterTable.
dhcpSnoopCounterTable	1.3.6.1.4.1.6321.1.2.3.1.13.11.2		not-accessible	This table shows the DHCP statistics.
INT dhcpSnoopEnable	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.1	INTEGER	read-write	Enable/disable DHCP snooping for a port.
IP dhcpSnoopGateway	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.5	IpAddress	read-only	The snooped Gateway.
IP dhcpSnoopIp	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.1	IpAddress	read-only	The snooped IP address.
dhcpSnoopIpEntry	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1		not-accessible	An entry of dhcpSnoopIpTable.
dhcpSnoopIpTable	1.3.6.1.4.1.6321.1.2.3.1.13.11.1		not-accessible	This table shows the IP addresses and netmasks offered by the DHCP server.
PHY dhcpSnoopMac	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.2	PhysAddress	read-only	The snooped MAC address.
INT dhcpSnoopMask	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.4	INTEGER	read-only	The snooped IP mask
INT dhcpSnoopMaxcnt	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.2	INTEGER	read-write	Set the max entries of the DHCP ARP table.
INT dhcpSnoopMaxcntMode	1.3.6.1.4.1.6321.1.2.3.1.10.55.6	INTEGER	read-write	When DHCP snooping table is full, new DHCP lease will replace first one in option 0 or will be dropped in option 1.
INT dhcpSnoopOps	1.3.6.1.4.1.6321.1.2.3.1.10.55.3	INTEGER	read-write	The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: DHCP snooping table flush.
dhcpSnoopPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1		not-accessible	An entry of dhcpSnoopPortTable.
dhcpSnoopPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.55.1		not-accessible	This table includes DHCP snooping enable/disable for each port.
OCT dhcpSnoopRouteMap	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.6	OCTET STRING	read-only	The refrence bit map of the dhcp route
INT dhcpSnoopSmacverifyEnable	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.3	INTEGER	read-write	Enable/disable DHCP source MAC verify for a port.
OCT dhcpSnoopTarget	1.3.6.1.4.1.6321.1.2.3.1.10.55.2	OCTET STRING	read-write	This managed object is used for identify the target on which the operation should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
VLA dhcpSnoopVid	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.3	VlanIndex	read-only	The snooped VLAN ID.
dhcpStaticEntry	1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1		not-accessible	An entry of dhcpStaticTable.
IP dhcpStaticIpAddr	1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.1	IpAddress	read-only	The IP address which can pass through the port.
ROW dhcpStaticRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.2	RowStatus	read-create	Row status of the table entry.
dhcpStaticTable	1.3.6.1.4.1.6321.1.2.3.1.10.55.4		not-accessible	This table defines DHCP static IP addresses.
dhcpStats	1.3.6.1.4.1.6321.1.2.3.1.13.11
diagnostic	1.3.6.1.4.1.6321.1.2.3.1.4
dsbCastCtrl	1.3.6.1.4.1.6321.1.2.3.1.11.11
INT dsBcastCtrlEnable	1.3.6.1.4.1.6321.1.2.3.1.11.11.1	INTEGER	read-write	Enable/disable downstream broadcast control.
INT dsBcastCtrlRate	1.3.6.1.4.1.6321.1.2.3.1.11.11.2	INTEGER	read-write	32~1000000 in step of 32 kbps
dsBcastDisableEntry	1.3.6.1.4.1.6321.1.2.3.1.8.9.1		not-accessible	An entry in Down Stream Bcast table.
ROW dsBcastDisableRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.9.1.2	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
dsBcastDisableTable	1.3.6.1.4.1.6321.1.2.3.1.8.9		not-accessible	This table includes Down Stream Bcast configuration.
INT dsBcastDisableVlanId	1.3.6.1.4.1.6321.1.2.3.1.8.9.1.1	INTEGER	read-only	downstream broadcast disabled vid.
dscp	1.3.6.1.4.1.6321.1.2.3.1.10.10
dscpMappingEntry	1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1		not-accessible	An entry of dscpMappingTable.
dscpMappingTable	1.3.6.1.4.1.6321.1.2.3.1.10.10.1		not-accessible	The table contains DSCP mapping configuration for the adsl and ethernet ports.
INT dscpMapPriority	1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.3	INTEGER	read-write	The mapping p bits that will replace the source p bits in the incoming packet.
dscpPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1		not-accessible	An entry of dscpPortTable.
dscpPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.10.2		not-accessible	The table contains DSCP mapping configuration for the adsl and ethernet ports.
INT dscpSrcCodePoint	1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.1	INTEGER	read-only	The DSCP source code point used for mapping.
INT dscpStatusEnable	1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1.1	INTEGER	read-write	The DSCP port status.
dslRate	1.3.6.1.4.1.6321.1.2.3.1.8.16
dslRateEntry	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1		not-accessible	An entry of dslRateTable.
INT dslRateLatencyMode	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.2	INTEGER	read-only	The latency mode is fast or interleave
INT dslRateMode	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.1	INTEGER	read-write	Configure DSL Rate configuration mode of the specified ports. Profile: the DSL Rate configuration comes from DSL profile. Line: the DSL Rate configuration comes from line configuration.
dslRateTable	1.3.6.1.4.1.6321.1.2.3.1.8.16.1		not-accessible	A table containing the per port DSL Rate configuration.
INT dslRateXtucMaxInterleaveDelay	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.3	INTEGER	read-write	Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
U32 dslRateXtucMaxTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.4	Unsigned32	read-write	Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
U32 dslRateXtucMinTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.5	Unsigned32	read-write	Configured Minimum Transmit rate for `Fast' or `Interleave' channels, in bps
INT dslRateXturMaxInterleaveDelay	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.6	INTEGER	read-write	Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency
U32 dslRateXturMaxTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.7	Unsigned32	read-write	Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
U32 dslRateXturMinTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.8	Unsigned32	read-write	Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
dtpvc	1.3.6.1.4.1.6321.1.2.3.1.8.14
STR dtpvcAcName	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.11	DisplayString	read-create	Access concentrator name for paepvc.
INT dtpvcCpriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.6	INTEGER	read-create	c-tag priority of the pvc.
VLA dtpvcCvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.5	VlanIndex	read-create	c-tag VLAN ID of the pvc.
STR dtpvcDSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.7	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in DS side.
dtpvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1		not-accessible	An entry of dtpvcTable.
INT dtpvcHelloTime	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.13	INTEGER	read-create	The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
ROW dtpvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.9	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
STR dtpvcServiceName	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.12	DisplayString	read-create	Service name for paepvc.
INT dtpvcSpriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.4	INTEGER	read-create	s-tag priority of the pvc.
STR dtpvcStateChannelType	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.8	DisplayString	read-only	The value of this object identifies the channel type at runtime.
INT dtpvcStateCPriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.6	INTEGER	read-only	C-priority of the dtpvc.
VLA dtpvcStateCvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.5	VlanIndex	read-only	Default C-VID of the dtpvc.
STR dtpvcStateEncap	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.9	DisplayString	read-only	The value of this object identifies the channel encapsulation at runtime.
dtpvcStateEntry	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1		not-accessible	An entry in dtpvcStateTable.
INT dtpvcStateSPriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.4	INTEGER	read-only	S-priority of the dtpvc.
VLA dtpvcStateSvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.3	VlanIndex	read-only	Default S-VID of the dtpvc.
dtpvcStateTable	1.3.6.1.4.1.6321.1.2.3.1.8.14.2		not-accessible	This table show current DTPVC status.
INT dtpvcStateVci	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.2	INTEGER	read-only	VCI of the dtpvc.
INT dtpvcStateVpi	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.1	INTEGER	read-only	VPI of the dtpvc.
INT dtpvcSuperChannel	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.10	INTEGER	read-create	Specified the configured DTPVC is a super channel.
VLA dtpvcSvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.3	VlanIndex	read-only	s-tag VLAN ID of the pvc.
dtpvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.14.1		not-accessible	This table includes Double Tagging (DT) PVC configuration.
STR dtpvcUSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.8	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in US side.
INT dtpvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.2	INTEGER	read-only	VCI of the pvc.
INT dtpvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.1	INTEGER	read-only	VPI of the pvc.
e5x100	1.3.6.1.4.1.6321.1.2.3
e5x110	1.3.6.1.4.1.6321.1.2.3.1
enetMtu	1.3.6.1.4.1.6321.1.2.3.1.10.13
INT enetMtuEntry	1.3.6.1.4.1.6321.1.2.3.1.10.13.1	INTEGER	read-write	Sets the MTU size for layer 2 frame, size from 1526 to 1532, default value is 1526.
enetSfpInfoEntry	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1		not-accessible	An entry in enetSfpInfoTable.
INT enetSfpInfoRxpower	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.2	INTEGER	read-only	Measured Rx Output Power.
enetSfpInfoTable	1.3.6.1.4.1.6321.1.2.3.1.13.17.2		not-accessible	This table includes sfp info of enet port.
INT enetSfpInfoTemperature	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.3	INTEGER	read-only	Measured temperature.
INT enetSfpInfoTxBias	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.4	INTEGER	read-only	Measured tx bias.
INT enetSfpInfoTxpower	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.1	INTEGER	read-only	Measured Tx Output Power.
INT enetSfpInfoVoltage	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.5	INTEGER	read-only	Measured voltage.
enetStats	1.3.6.1.4.1.6321.1.2.3.1.13.17
extAlarm	1.3.6.1.4.1.6321.1.2.3.1.11.8
extAlarmEntry	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1		not-accessible	The entry of external alarm table.
INT extAlarmIndex	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.1	INTEGER	read-only	The index of the entry.
STR extAlarmname	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.2	DisplayString	read-write	The external alarm name.
STR extAlarmstatus	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.3	DisplayString	read-only	Dispaly 'Normal' or 'Alarm' string
extAlarmTable	1.3.6.1.4.1.6321.1.2.3.1.11.8.1		not-accessible	A table that contains external alarm information.
INT extAlarmTriggeredMode	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.4	INTEGER	read-write	The external alarm triggered mode.
fwUpgrade	1.3.6.1.4.1.6321.1.2.3.1.11.14
INT fwUpgradeCheck	1.3.6.1.4.1.6321.1.2.3.1.11.14.2	INTEGER	read-write	Enable/disable firmware upgrade version checking feature.
STR fwUpgradeStatus	1.3.6.1.4.1.6321.1.2.3.1.11.14.3	DisplayString	read-only	Display current firmware upgrade status.
OCT fwUpgradeVersion	1.3.6.1.4.1.6321.1.2.3.1.11.14.1	OCTET STRING	read-write	Configure the target firmware version that will be upgraded.
gbond	1.3.6.1.4.1.6321.1.2.3.1.8.51
U32 gbondGroupDownRate	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.5	Unsigned32	read-only	The DOWN stream rate.
gbondGroupEntry	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1		not-accessible	An entry of gbondTable.
OCT gbondGroupName	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.1	OCTET STRING	read-only	An administratively assigned string, which may be used to identify bonding group.
OCT gbondGroupPorts	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.2	OCTET STRING	read-create	The set of ports which are currently assigned to the bonding group of specified group name. Byte 1: Reserved(chassis) Byte 2~3: Reserved(slot) Byte 4: Reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
ROW gbondGroupRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.6	RowStatus	read-create	This object indicates the status of this entry.
gbondGroupTable	1.3.6.1.4.1.6321.1.2.3.1.8.51.1		not-accessible	A table containing the G.Bond configuration information for each bonding group of the device.
U32 gbondGroupUpRate	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.4	Unsigned32	read-only	The UP stream rate.
iesSeriesCommon	1.3.6.1.4.1.6321.1.2.3.1.98
igmpCount	1.3.6.1.4.1.6321.1.2.3.1.7.5
INT igmpCountPortEnable	1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.1	INTEGER	read-write	Enable/disable IGMP count limiting for a port.
igmpCountPortEntry	1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1		not-accessible	An entry of igmpCountPortTable.
INT igmpCountPortLimit	1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.2	INTEGER	read-write	The maximum allowed IGMP report count for a port.
igmpCountPortTable	1.3.6.1.4.1.6321.1.2.3.1.7.5.1		not-accessible	This table specify the IGMP count limiting of the port.
INT igmpEnable	1.3.6.1.4.1.6321.1.2.3.1.7.1	INTEGER	read-write	Enable/disable IGMP protocol.
IP igmpFilterEndIp	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.3	IpAddress	read-create	The end IP of the filter rule.
igmpFilterEntry	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1		not-accessible	The entry of IGMP Filter table.
INT igmpFilterIndex	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.1	INTEGER	read-only	The index which specifies the filter rule.
IP igmpFilterStartIp	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.2	IpAddress	read-create	The start IP of the filter rule.
igmpFilterTable	1.3.6.1.4.1.6321.1.2.3.1.7.13.3		not-accessible	A table that contains IGMP Filters.
igmpGroupEntry	1.3.6.1.4.1.6321.1.2.3.1.13.5.1		not-accessible	An entry in igmpGroupTable.
IP igmpGroupIp	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.1	IpAddress	read-only	igmp group IP
POR igmpGroupMemberPorts	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.4	PortList	read-only	Group Member Ports
INT igmpGroupnumberOfMembers	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.3	INTEGER	read-only	number Of Members
igmpGroupPortEntry	1.3.6.1.4.1.6321.1.2.3.1.13.6.1		not-accessible	An entry in igmpGroupPortTable.
IP igmpGroupPortIp	1.3.6.1.4.1.6321.1.2.3.1.13.6.1.1	IpAddress	read-only	Igmp Group IP
igmpGroupPortTable	1.3.6.1.4.1.6321.1.2.3.1.13.6		not-accessible	This table includes igmp Group port information.
igmpGroupPortV2Entry	1.3.6.1.4.1.6321.1.2.3.1.13.8.1		not-accessible	An entry of igmpGroupPortV2Table.
IP igmpGroupPortV2Ip	1.3.6.1.4.1.6321.1.2.3.1.13.8.1.2	IpAddress	read-only	The multicast IP address.
IP igmpGroupPortV2SourceIp	1.3.6.1.4.1.6321.1.2.3.1.13.8.1.3	IpAddress	read-only	The source IP address that joins the IGMP group.
igmpGroupPortV2Table	1.3.6.1.4.1.6321.1.2.3.1.13.8		not-accessible	A table that displays IGMP joined groups in this port.
VLA igmpGroupPortV2Vid	1.3.6.1.4.1.6321.1.2.3.1.13.8.1.1	VlanIndex	read-only	The IGMP group VLAN ID.
INT igmpGroupPortvid	1.3.6.1.4.1.6321.1.2.3.1.13.6.1.2	INTEGER	read-only	Igmp Group vid
igmpGroupTable	1.3.6.1.4.1.6321.1.2.3.1.13.5		not-accessible	This table includes igmp group information.
igmpGroupV2Entry	1.3.6.1.4.1.6321.1.2.3.1.13.7.1		not-accessible	An entry of igmpGroupV2Table.
IP igmpGroupV2Ip	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.2	IpAddress	read-only	The multicast IP address.
POR igmpGroupV2MemberPorts	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.4	PortList	read-only	The member port list of the group.
INT igmpGroupV2NumOfMembers	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.3	INTEGER	read-only	The number of member ports in the group.
igmpGroupV2Table	1.3.6.1.4.1.6321.1.2.3.1.13.7		not-accessible	A table that displays IGMP learned group member information.
VLA igmpGroupV2Vid	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.1	VlanIndex	read-only	The IGMP group VLAN ID.
INT igmpGroupvid	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.2	INTEGER	read-only	vlan id
INT igmpLastMemQryInterval	1.3.6.1.4.1.6321.1.2.3.1.7.11.4	INTEGER	read-write	Set IGMP Last Member Query interval, 1~5 in 100 milliseconds.
INT igmpLastMemQryRobust	1.3.6.1.4.1.6321.1.2.3.1.7.11.5	INTEGER	read-write	Set Last Member Query Robustness, 1~5.
C32 igmpLeaveCntTotal	1.3.6.1.4.1.6321.1.2.3.1.13.3	Counter32	read-only	The total number of IGMP leave messages received.
INT igmpLeaveMode	1.3.6.1.4.1.6321.1.2.3.1.7.10	INTEGER	read-write	Configure IGMP leave message handling mode.
INT igmpNumOfActiveGroups	1.3.6.1.4.1.6321.1.2.3.1.13.4	INTEGER	read-only	The total number of IGMP learned groups.
C32 igmpPortCtrlAuditLeaveCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.5	Counter32	read-only	The total number of groups left by audit query.
igmpPortCtrlPduEntry	1.3.6.1.4.1.6321.1.2.3.1.13.9.1		not-accessible	An entry of igmpPortCtrlPduTable.
C32 igmpPortCtrlPduLeaveCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.3	Counter32	read-only	The total number of IGMP leave messages received in this port.
C32 igmpPortCtrlPduQueryCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.1	Counter32	read-only	The total number of IGMP query messages received in this port.
C32 igmpPortCtrlPduReportCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.2	Counter32	read-only	The total number of IGMP report messages received in this port.
igmpPortCtrlPduTable	1.3.6.1.4.1.6321.1.2.3.1.13.9		not-accessible	A table that displays IGMP related counter values in this port.
INT igmpPortNumOfActiveGroups	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.4	INTEGER	read-only	The total number of active IGMP groups in this port.
igmpProfile	1.3.6.1.4.1.6321.1.2.3.1.7.13
INT igmpProfileEnable	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.2	INTEGER	read-write	Enable/disable IGMP Profile.
igmpProfileEntry	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1		not-accessible	The entry of IGMP Profile table.
INT igmpProfileMaxGroup	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.3	INTEGER	read-write	Set maximum allowed multicast group, 1~16.
STR igmpProfileName	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.1	DisplayString	read-only	The IGMP Profile name.
igmpProfilePortEntry	1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1		not-accessible	An entry in igmpProfilePortTable.
OCT igmpProfilePortProfile	1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1.1	OCTET STRING	read-write	The IGMP Profile of the port.
igmpProfilePortTable	1.3.6.1.4.1.6321.1.2.3.1.7.13.4		not-accessible	This table specifies the IGMP Profile of the port.
ROW igmpProfileRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.4	RowStatus	read-create	The row status of the IGMP Profile entry.
igmpProfileTable	1.3.6.1.4.1.6321.1.2.3.1.7.13.2		not-accessible	A table that contains IGMP Profiles.
INT igmpQryInterval	1.3.6.1.4.1.6321.1.2.3.1.7.11.1	INTEGER	read-write	Set IGMP query interval, 10~1000 in seconds.
INT igmpQryRespInterval	1.3.6.1.4.1.6321.1.2.3.1.7.11.3	INTEGER	read-write	Set IGMP query response interval, 1~100 in 100 milliseconds.
C32 igmpQueryCntTotal	1.3.6.1.4.1.6321.1.2.3.1.13.1	Counter32	read-only	The total number of IGMP query messages received.
C32 igmpReportCntTotal	1.3.6.1.4.1.6321.1.2.3.1.13.2	Counter32	read-only	The total number of IGMP report messages received.
INT igmpRobust	1.3.6.1.4.1.6321.1.2.3.1.7.11.2	INTEGER	read-write	Set IGMP query Robustness, 1~5.
igmpTimer	1.3.6.1.4.1.6321.1.2.3.1.7.11
INT igmpVersion	1.3.6.1.4.1.6321.1.2.3.1.7.9	INTEGER	read-write	Setting IGMP version.
ipbpvc	1.3.6.1.4.1.6321.1.2.3.1.8.12
INT ipbpvcDomainDhcpVlanEnable	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.2	INTEGER	read-create	Enable/disable DHCP VLAN in a domain.
ipbpvcDomainEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1		not-accessible	An entry of ipbpvcDomainTable.
OCT ipbpvcDomainName	1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.1	OCTET STRING	read-only	Name of the domain.
ROW ipbpvcDomainRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.2	RowStatus	read-create	Row status of the table.
ipbpvcDomainTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.1		not-accessible	This table includes ipbpvc domain configuration. This table is supported by R3.00 and later versions.
ipbpvcDomainVlanEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1		not-accessible	An entry of ipbpvcDomainVlanTable.
VLA ipbpvcDomainVlanId	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.1	VlanIndex	read-only	Set VLAN to join or leave the specified domain.
ROW ipbpvcDomainVlanRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.3	RowStatus	read-create	Row status of the table used to create/delete an entry.
ipbpvcDomainVlanTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.2		not-accessible	This table includes ipbpvc domain VLAN configuration. This table is supported by R3.00 and later versions.
ipbpvcEdgeRouterEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1		not-accessible	An entry of ipbpvcEdgeRouterTable.
IP ipbpvcEdgeRouterIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.1	IpAddress	read-only	IP address of the edge router.
INT ipbpvcEdgeRouterMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.3	INTEGER	read-only	Netmask of the edge router.
ROW ipbpvcEdgeRouterRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.4	RowStatus	read-create	Row status of the table used to create/delete an entry.
ipbpvcEdgeRouterTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.3		not-accessible	This table includes ipbpvc edge router configuration. This table is supported by R3.00 and later versions.
VLA ipbpvcEdgeRouterVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.2	VlanIndex	read-only	VLAN ID of the edge router.
INT ipbpvcEncap	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.4	INTEGER	read-create	Type of the PVC.
ipbpvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1		not-accessible	An entry of ipbpvcTable.
ipbpvcIfDynamicEntry	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1		not-accessible	An entry of ipbpvcIfDynamicTable.
INT ipbpvcIfDynamicIfIndex	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.3	INTEGER	read-only
IP ipbpvcIfDynamicIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.1	IpAddress	read-only
INT ipbpvcIfDynamicMask	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.2	INTEGER	read-only
ipbpvcIfDynamicTable	1.3.6.1.4.1.6321.1.2.3.1.13.14.2		not-accessible	Display runtime interfaces. This table is supported by R3.00 and later versions.
INT ipbpvcIfDynamicVci	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.5	INTEGER	read-only
INT ipbpvcIfDynamicVpi	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.4	INTEGER	read-only
ipbpvcInterfaceEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1		not-accessible	An entry of ipbpvcInterfaceTable.
INT ipbpvcInterfaceIfIndex	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.4	INTEGER	read-create	IfIndex of the interface.
IP ipbpvcInterfaceIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.1	IpAddress	read-only	IP address of the interface.
INT ipbpvcInterfaceMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.2	INTEGER	read-only	Netmask of the interface.
ROW ipbpvcInterfaceRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.7	RowStatus	read-create	Row status of the table used to create/delete an entry.
ipbpvcInterfaceTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.4		not-accessible	This table includes ipbpvc interface configuration. This table is supported by R3.00 and later versions.
INT ipbpvcInterfaceVci	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.6	INTEGER	read-create	VCI of the interface.
VLA ipbpvcInterfaceVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.3	VlanIndex	read-only	VLAN ID of the interface.
INT ipbpvcInterfaceVpi	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.5	INTEGER	read-create	VPI of the interface.
INT ipbpvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.5	INTEGER	read-create	Priority of the PVC.
OCT ipbpvcProfile	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.6	OCTET STRING	read-create	Profile of the PVC.
OCT ipbpvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.8	OCTET STRING	read-create	US Profile of the PVC.
INT ipbpvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.3	INTEGER	read-only	PVID of the PVC.
ipbpvcRouteDynamicEntry	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1		not-accessible	An entry of ipbpvcRouteDynamicTable.
IP ipbpvcRouteDynamicIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.2	IpAddress	read-only
INT ipbpvcRouteDynamicMask	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.3	INTEGER	read-only
INT ipbpvcRouteDynamicMetric	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.5	INTEGER	read-only
IP ipbpvcRouteDynamicNextHop	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.4	IpAddress	read-only
INT ipbpvcRouteDynamicPriority	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.6	INTEGER	read-only
ipbpvcRouteDynamicTable	1.3.6.1.4.1.6321.1.2.3.1.13.14.3		not-accessible	Display runtime routing table. This table is supported by R3.00 and later versions.
INT ipbpvcRouteDynamicType	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.1	INTEGER	read-only
ipbpvcRouteEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1		not-accessible	An entry of ipbpvcRouteTable.
IP ipbpvcRouteIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.1	IpAddress	read-only	IP address of the route.
INT ipbpvcRouteMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.2	INTEGER	read-only	Netmask of the route.
INT ipbpvcRouteMetric	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.4	INTEGER	read-create	Metric of the route.
IP ipbpvcRouteNextHop	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.3	IpAddress	read-only	Next hop IP address of the route.
INT ipbpvcRoutePriority	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.5	INTEGER	read-create	Priority of the route. Note that the default value of this object is 8, which means we keep the original priority of the packet(frame).
ROW ipbpvcRouteRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.6	RowStatus	read-create	Row status of the table used to create/delete an entry.
ipbpvcRouteTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.5		not-accessible	This table includes ipbpvc route configuration. This table is supported by R3.00 and later versions.
INT ipbpvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.7	INTEGER	read-create	Row status of the table used to create/delete an entry.
ipbpvcStats	1.3.6.1.4.1.6321.1.2.3.1.13.14
ipbpvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.6		not-accessible	This table includes ipbpvc configuration. This table is supported by R3.00 and later versions.
INT ipbpvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.2	INTEGER	read-only	VCI of the PVC.
INT ipbpvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.1	INTEGER	read-only	VPI of the PVC.
INT isConfigChanged	1.3.6.1.4.1.6321.1.2.3.1.11.13	INTEGER	read-only	If system configuration has been changed.
MAC macAddress	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.1	MacAddress	read-only	A unicast MAC address for which the bridge has forwarding and/or filtering information.
INT macDisplayTarget	1.3.6.1.4.1.6321.1.2.3.1.13.13.1	INTEGER	read-write	This managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. The target could be: 99: all ports in the system 98: all subscriber ports 97: all Ethernet ports IfIndex is used for identifying subscriber ports and Ethernet Ports(e.g. 1 ~ 50).
macEntry	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1		not-accessible	An entry of macTable.
macff	1.3.6.1.4.1.6321.1.2.3.1.10.60
IP macFfArIP	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.3	IpAddress	read-write	IP of this AR/AS
macFfArpCounterEntry	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1		not-accessible	An entry of macFfArpCounterTable.
C32 macFfArpCounterReplyRX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.5	Counter32	read-only	ARP Reply RX counter.
C32 macFfArpCounterReplyRXDrop	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.6	Counter32	read-only	ARP Reply RX drop counter.
C32 macFfArpCounterReplyTX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.4	Counter32	read-only	ARP Reply TX counter.
C32 macFfArpCounterRequestRX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.2	Counter32	read-only	ARP Request RX counter.
C32 macFfArpCounterRequestRXDrop	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.3	Counter32	read-only	ARP Request RX drop counter.
C32 macFfArpCounterRequestTX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.1	Counter32	read-only	ARP Request TX counter.
macFfArpCounterTable	1.3.6.1.4.1.6321.1.2.3.1.13.16.3		not-accessible	A table that contains MAC Force Forwarding ARP counter information.
macFfArpEntry	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1		not-accessible	An entry of macFfArpTable.
INT macFfArpFlush	1.3.6.1.4.1.6321.1.2.3.1.10.60.3	INTEGER	read-write	Set the object to 1 to flush mac table.
IP macFfArpIP	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.2	IpAddress	read-only	IP of this AR/AS.
PHY macFfArpMac	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.4	PhysAddress	read-only	MAC address of the AR or AS.
INT macFfArpPort	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.3	INTEGER	read-only	Port of this AR/AS.
macFfArpTable	1.3.6.1.4.1.6321.1.2.3.1.13.16.2		not-accessible	A table that contains MAC Force Forwarding ARP information.
VLA macFfArpVid	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.1	VlanIndex	read-only	The VLAN-ID refering to this AR/AS.
macFfEntry	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1		not-accessible	An entry of macFfTable.
INT macFfIndex	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.1	INTEGER	read-only	Index of the MACFF.
ROW macFfRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.6	RowStatus	read-create	The row status of the MacFfEntry entry.
IP macFfSrcIP	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.4	IpAddress	read-write	The source IP address of the MACFF.
INT macFfSrcMask	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.5	INTEGER	read-write	The subnet mask of source IP mask.
IP macFfstaticIP	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.3	IpAddress	read-only	The specified IP range.
macFfStaticIPEntry	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1		not-accessible	An entry of macFfTable.
INT macFfStaticIPMask	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.4	INTEGER	read-only	Mask_bits is 24 .. 32.
INT macFfStaticIPPort	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.1	INTEGER	read-only	The port number, 1 ~ 48.
ROW macFfStaticIPRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.5	RowStatus	read-create	The row status used to configure the table entry.
macFfStaticIPTable	1.3.6.1.4.1.6321.1.2.3.1.10.60.6		not-accessible
INT macFfStaticIPVid	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.2	INTEGER	read-only	VLAN ID of the IP range, 1 ~ 4094, the vid should be enable the MACFF function first.
macffStats	1.3.6.1.4.1.6321.1.2.3.1.13.16
IP macFfStatsArIP	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.3	IpAddress	read-only	IP of this AR/AS
macFfStatsEntry	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1		not-accessible	An entry of macFfStatsTable.
INT macFfStatsIndex	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.1	INTEGER	read-only	Index of the MACFF.
IP macFfStatsSrcIP	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.4	IpAddress	read-only	The source IP address of the MACFF.
INT macFfStatsSrcMask	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.5	INTEGER	read-only	The subnet mask of source IP mask.
macFfStatsTable	1.3.6.1.4.1.6321.1.2.3.1.13.16.1		not-accessible	A table that contains MAC Force Forwarding static configuration and dynamic information.
VLA macFfStatsVid	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.2	VlanIndex	read-only	The VLAN-ID refering to this AR/AS.
macFfTable	1.3.6.1.4.1.6321.1.2.3.1.10.60.1		not-accessible	A table that contains MAC Force Forwarding configuration.
INT macFfVid	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.2	INTEGER	read-write	The VLAN-ID refering to this AR/AS.
macFfVlanEntry	1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1		not-accessible	An entry of macFfVlanTable.
ROW macFfVlanRowstatus	1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.1	RowStatus	read-create	Row status of the table used to create/delete an entry.
macFfVlanTable	1.3.6.1.4.1.6321.1.2.3.1.10.60.5		not-accessible	A table that contains MAC Force Forwarding Vlan configuration.
INT macFfVlanUnknownUnicast	1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.2	INTEGER	read-create	Setting downstream unknown uni-cast packet on macff vlan to flooding or dropping.
macfilter	1.3.6.1.4.1.6321.1.2.3.1.10.53
PHY macFilterAddr	1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.1	PhysAddress	read-only	The mac address which can pass through or be rejected from the port.
macfilterBatchSet	1.3.6.1.4.1.6321.1.2.3.1.10.53.6
macFilterEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1		not-accessible	The entry of macFilterTable.
INT macFilterMacCountForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.10.53.6.3	INTEGER	read-write	The total number of MAC addresses allowed for a port.
INT macfilterOps	1.3.6.1.4.1.6321.1.2.3.1.10.53.6.2	INTEGER	read-write	The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable mac filter BIT 2: enable mac count filter BIT 3: disable mac filter BIT 4: set mac count BIT 5: disable mac count filter.
INT macFilterPortEnable	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.1	INTEGER	read-write	Enable/disable MAC filtering for the port.
macFilterPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1		not-accessible	An entry in macFilterPortTable.
INT macFilterPortFilterMode	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.3	INTEGER	read-write	The mac filter mode (accept or deny) for the port.
INT macFilterPortMacCount	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.2	INTEGER	read-write	The total number of MAC addresses allowed for the port.
macFilterPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.1		not-accessible	This table includes the status of mac filtering for each port.
ROW macFilterRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.2	RowStatus	read-create	The row status of the entry.
macFilterTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.5		not-accessible	A table that contains the mac filter addresses.
OCT macfilterTarget	1.3.6.1.4.1.6321.1.2.3.1.10.53.6.1	OCTET STRING	read-write	This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chassis) Byte 2~3: 0, Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
INT macPort	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.2	INTEGER	read-only	The port from which the mac address has been learned.
macStats	1.3.6.1.4.1.6321.1.2.3.1.13.13
INT macStatus	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.3	INTEGER	read-only	The status of this entry.
macTable	1.3.6.1.4.1.6321.1.2.3.1.13.13.2		not-accessible	A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
INT maxNumberOfIgmpProfiles	1.3.6.1.4.1.6321.1.2.3.1.7.13.1	INTEGER	read-only	The max number of IGMP profiles in the system.
INT maxNumOfDhcpStaticIp	1.3.6.1.4.1.6321.1.2.3.1.10.55.5	INTEGER	read-only	The maximum number of DHCP static IP addresses which can be created for a port.
INT maxNumOfMacFfVlanInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.60.4	INTEGER	read-only	The max number of macff Vlans supported in the system.
INT maxNumOfMacFiltersInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.53.2	INTEGER	read-only	The max number of mac filters supported in the system.
INT maxNumOfMacFiltersPerPort	1.3.6.1.4.1.6321.1.2.3.1.10.53.3	INTEGER	read-only	The max number of mac filters supported per port.
INT maxNumOfMcastBw	1.3.6.1.4.1.6321.1.2.3.1.7.4.2	INTEGER	read-only	The maximum number of row entries that user can create in mcastBwTable.
INT maxNumOfMvlan	1.3.6.1.4.1.6321.1.2.3.1.7.6.1	INTEGER	read-only	The maximum number of row entries that user can create in mvlanTable.
INT maxNumOfOuiFiltersInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.53.10	INTEGER	read-only	The max number of OUI filters supported in system.
INT maxNumOfOuiFiltersPerPort	1.3.6.1.4.1.6321.1.2.3.1.10.53.8	INTEGER	read-only	The max number of OUI filters supported per port.
INT maxNumOfOuiFiltersPerVlan	1.3.6.1.4.1.6321.1.2.3.1.10.53.11	INTEGER	read-only	The max number of OUI filters supported per vlan.
INT maxNumOfPppoeDhcpRelay82Conf	1.3.6.1.4.1.6321.1.2.3.1.10.57.2	INTEGER	read-only	The maximum number of rows that can be created in pppoeAgentTable.
INT maxNumOfPriorityPvcs	1.3.6.1.4.1.6321.1.2.3.1.8.5.1	INTEGER	read-only	The maximum number of priority PVCs which could be created on a port.
INT maxNumOfPvcs	1.3.6.1.4.1.6321.1.2.3.1.8.4.1	INTEGER	read-only	The maximum number of PVCs which could be created on a port.
INT maxNumOfQryVid	1.3.6.1.4.1.6321.1.2.3.1.7.7.1	INTEGER	read-only	The maximum number of row entries that user can create in qryVidConfTable.
mcastBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4
INT mcastBwBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.4	INTEGER	read-create	The bandwidth budget for the multicast IP channels.
IP mcastBwEndIp	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.3	IpAddress	read-only	The end multicast IP of the bandwidth control range.
mcastBwEntry	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1		not-accessible	An entry of mcastBwTable.
INT mcastBwIndex	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.1	INTEGER	read-only	The index which specify the entry.
INT mcastBwPortBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.2	INTEGER	read-write	Set bandwidth threshold for a port.
INT mcastBwPortEnable	1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.1	INTEGER	read-write	Enable/disable multicast bandwidth control for a port.
mcastBwPortEntry	1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1		not-accessible	An entry of mcastBwPortTable.
mcastBwPortTable	1.3.6.1.4.1.6321.1.2.3.1.7.4.4		not-accessible	This table specify the multicast bandwidth control of the port.
ROW mcastBwRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.5	RowStatus	read-create	The row status of the entry.
IP mcastBwStartIp	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.2	IpAddress	read-only	The start multicast IP of the bandwidth control range.
mcastBwTable	1.3.6.1.4.1.6321.1.2.3.1.7.4.3		not-accessible	This table defines bandwidth budget for a range of multicast IP channels.
INT mcastDefaultBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4.1	INTEGER	read-write	Default bandwidth requirement for a multicast channel.
multicast	1.3.6.1.4.1.6321.1.2.3.1.7
mvlan	1.3.6.1.4.1.6321.1.2.3.1.7.6
POR mvlanEgressPorts	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.3	PortList	read-create	The set of ports which are permanently assigned to the egress list for this multicast VLAN.
mvlanEntry	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1		not-accessible	An entry of mvlanTable.
VLA mvlanIndex	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.1	VlanIndex	read-only	The VLAN-ID refering to this VLAN.
STR mvlanName	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.2	DisplayString	read-create	An administratively assigned string, which may be used to identify the VLAN.
ROW mvlanRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.5	RowStatus	read-create	This object indicates the status of this entry.
mvlanTable	1.3.6.1.4.1.6321.1.2.3.1.7.6.2		not-accessible	A table containing static configuration information for each multicast VLAN configured into the device.
IP mvlanTranslateEndIp	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.3	IpAddress	read-write	The end IP of the multicast VLAN translation.
mvlanTranslateEntry	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1		not-accessible	An entry of mvlanTranslateTable.
INT mvlanTranslateIndex	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.1	INTEGER	read-only	The index which specif the entry.
IP mvlanTranslateStartIp	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.2	IpAddress	read-write	The start IP of the multicast VLAN translation.
mvlanTranslateTable	1.3.6.1.4.1.6321.1.2.3.1.7.6.3		not-accessible	A table that contains multicast to VLAN translation.
POR mvlanUntaggedPorts	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.4	PortList	read-create	The set of ports which should transmit egress packets for this multicast VLAN as untagged.
OCT ouiFilterAddr	1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.1	OCTET STRING	read-only	The first three bytes of the mac address which can pass through or be rejected from the vlan.
OCT ouiFilterAddrOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.1	OCTET STRING	read-only	The first three bytes of the mac address which can pass through or be rejected from the port.
ouiFilterEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1		not-accessible	The entry of ouiFilterTable.
ouiFilterEntryOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1		not-accessible	The entry of ouiFilterTableOld.
INT ouiFilterPortEnable	1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.1	INTEGER	read-write	Enable/disable oui filtering for the port.
ouiFilterPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1		not-accessible	An entry in macFilterPortTable.
INT ouiFilterPortFilterMode	1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.2	INTEGER	read-write	The oui filter mode (accept or deny) for the port.
ouiFilterPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.9		not-accessible	This table includes the status of oui filtering for each port.
ROW ouiFilterRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.2	RowStatus	read-create	The row status of the entry.
ROW ouiFilterRowStatusOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.2	RowStatus	read-create	The row status of the entry.
ouiFilterTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.12		not-accessible	A table that contains the OUI filter addresses.
ouiFilterTableOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7		not-accessible	A table that contains the OUI filter addresses.
INT ouiFilterVlanEnable	1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.1	INTEGER	read-write	Enable/disable oui filtering for the VLAN.
ouiFilterVlanEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1		not-accessible	An entry in ouiFilterVlanTable.
INT ouiFilterVlanFilterMode	1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.2	INTEGER	read-write	The oui filter mode (accept or deny) for the VLAN.
ouiFilterVlanTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.13		not-accessible	This table includes the status of oui filtering for each configured VLAN.
paepvc	1.3.6.1.4.1.6321.1.2.3.1.8.10
STR paepvcAcName	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.7	DisplayString	read-create	Access concentrator name.
U32 paepvcCountAcSystemErrRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.13	Unsigned32	read-only	The number of pppoe access concentrator name error received
paepvcCountEntry	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1		not-accessible	An entry of paepvcCountTable.
U32 paepvcCountGenericErrRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.15	Unsigned32	read-only	The number of pppoe generic error received
U32 paepvcCountGenericErrTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.14	Unsigned32	read-only	The number of pppoe generic error transfered
U32 paepvcCountPadiTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.6	Unsigned32	read-only	The number of pppoe padi transfered
U32 paepvcCountPadoRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.7	Unsigned32	read-only	The number of pppoe pado received
U32 paepvcCountPadrTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.8	Unsigned32	read-only	The number of pppoe padr transfered
U32 paepvcCountPadsRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.9	Unsigned32	read-only	The number of pppoe pads received
U32 paepvcCountPadtRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.11	Unsigned32	read-only	The number of pppoe padt received
U32 paepvcCountPadtTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.10	Unsigned32	read-only	The number of pppoe padt transfered
U32 paepvcCountPppLcpCfgReqRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.3	Unsigned32	read-only	The number of ppp lcp config-request received.
U32 paepvcCountPppLcpEchoReplyRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.5	Unsigned32	read-only	The number of ppp lcp echo-reply received.
U32 paepvcCountPppLcpEchoReqRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.4	Unsigned32	read-only	The number of ppp lcp echo-request received.
U32 paepvcCountSrvcnameErrRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.12	Unsigned32	read-only	The number of pppoe service name error received
paepvcCountTable	1.3.6.1.4.1.6321.1.2.3.1.13.12.2		not-accessible	This table shows the paepvc counters.
INT paepvcCountVci	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.2	INTEGER	read-only	The PAEPVC VCI.
INT paepvcCountVpi	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.1	INTEGER	read-only	The PAEPVC VPI.
INT paepvcCPriority	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.13	INTEGER	read-create	802.1p default C-priority of the pvc.
VLA paepvcCvid	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.12	VlanIndex	read-create	Default C-VID of the pvc.
paepvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1		not-accessible	An entry of paepvcTable.
INT paepvcHelloTime	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.9	INTEGER	read-create	The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
INT paepvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.5	INTEGER	read-create	802.1p default priority of the pvc.
STR paepvcProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.6	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
STR paepvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.11	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
VLA paepvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.3	VlanIndex	read-only	Default VID of the pvc.
ROW paepvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.10	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
STR paepvcServiceName	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.8	DisplayString	read-create	Service name.
STR paepvcSessionacname	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.6	DisplayString	read-only	Access concentrator name.
paepvcSessionEntry	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1		not-accessible	An entry of paepvcSessionTable.
INT paepvcSessionId	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.4	INTEGER	read-only	The PAEPVC session ID.
STR paepvcSessionsrvcname	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.7	DisplayString	read-only	Service name.
INT paepvcSessionState	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.3	INTEGER	read-only	The PAEPVC status.
paepvcSessionTable	1.3.6.1.4.1.6321.1.2.3.1.13.12.1		not-accessible	This table shows the paepvc session statistics.
U32 paepvcSessionUptime	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.5	Unsigned32	read-only	The PAEPVC session uptime.
INT paepvcSessionVci	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.2	INTEGER	read-only	The PAEPVC VCI.
INT paepvcSessionVpi	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.1	INTEGER	read-only	The PAEPVC VPI.
paepvcStats	1.3.6.1.4.1.6321.1.2.3.1.13.12
paepvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.10.1		not-accessible	This table includes PPPoAoE PVC configuration.
INT paepvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.2	INTEGER	read-only	VCI of the pvc.
INT paepvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.1	INTEGER	read-only	VPI of the pvc.
port	1.3.6.1.4.1.6321.1.2.3.1.8
INT powerMgmtAtucMaxPSD	1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.1	INTEGER	read-write	The object specifies the maximum ATU-C PSD.
INT powerMgmtAturMaxPSD	1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.2	INTEGER	read-write	The object specifies the maximum ATU-R PSD.
INT powerMgmtL0Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.1	INTEGER	read-write	The object specifies the minimum time in L0 mode before L2 mode may be entered.
INT powerMgmtL2Atpr	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.3	INTEGER	read-write	The maximum Aggregate Transmit Power Reduction.
INT powerMgmtL2Atprt	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.4	INTEGER	read-write	The maximum Aggregate Transmit Power Reduction Total.
INT powerMgmtL2MaxRate	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.6	INTEGER	read-write	The object specifies the maximum L2 rate.
INT powerMgmtL2MinRate	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.5	INTEGER	read-write	The object specifies the minimum L2 rate.
INT powerMgmtL2ThreshRate	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.7	INTEGER	read-write	The object specifies the rate threshold that triggers the line entering L0 or L2 mode.
INT powerMgmtL2Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.2	INTEGER	read-write	The object specifies the minimum time in L2 mode before trimming and in between power trims.
powerMgmtParamEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1		not-accessible	An entry in powerMgmtParamTable.
powerMgmtParamTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.5		not-accessible	This table defines L0 to L2 power transition parameters.
powerMgmtPSDEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1		not-accessible	An entry in powerMgmtPSDTable.
powerMgmtPSDTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.6		not-accessible	This table provides the PSD setting for both ATU-C and ATU-R.
pppoeAgent	1.3.6.1.4.1.6321.1.2.3.1.10.57
INT pppoeAgentEnable	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.1	INTEGER	read-create	Enable/disable DHCP relay and Option82 function.
pppoeAgentEntry	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1		not-accessible	An entry of pppoeAgentTable.
STR pppoeAgentInfo	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.2	DisplayString	read-create	User specific Option82 information.
INT pppoeAgentOptionMode	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.4	INTEGER	read-create	Option82 format.
ROW pppoeAgentRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.3	RowStatus	read-create	Row status of the table entry.
pppoeAgentTable	1.3.6.1.4.1.6321.1.2.3.1.10.57.1		not-accessible	A table that contains PPPoE DHCP Relay configuration.
ppvc	1.3.6.1.4.1.6321.1.2.3.1.8.5
INT ppvcEncap	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.4	INTEGER	read-create	Encapsulation of the ppvc.
ppvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1		not-accessible	An entry in ppvcTable.
ppvcMemberEntry	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1		not-accessible	An entry in ppvcMemberTable.
INT ppvcMemberPriority	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.3	INTEGER	read-only	802.1p default priority of the member ppvc.
STR ppvcMemberProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.4	DisplayString	read-create	The profile of the member ppvc in DS side.
STR ppvcMemberProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.6	DisplayString	read-create	The profile of the member ppvc in US side.
ROW ppvcMemberRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.5	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ppvcMemberTable	1.3.6.1.4.1.6321.1.2.3.1.8.5.4		not-accessible	This table includes priority PVC member configuration.
INT ppvcMemberVci	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.2	INTEGER	read-only	VCI of the member ppvc.
INT ppvcMemberVpi	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.1	INTEGER	read-only	VPI of the member ppvc.
INT ppvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.5	INTEGER	read-create	802.1p default priority of the ppvc.
VLA ppvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.3	VlanIndex	read-only	Default VID of the ppvc.
ROW ppvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.6	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ppvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.5.2		not-accessible	This table includes priority PVC configuration.
INT ppvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.2	INTEGER	read-only	VCI of the ppvc.
INT ppvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.1	INTEGER	read-only	VPI of the ppvc.
pvc	1.3.6.1.4.1.6321.1.2.3.1.8.4
STR pvcAcName	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.11	DisplayString	read-create	Access concentrator name for paepvc.
pvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1		not-accessible	An entry in pvcTable.
INT pvcHelloTime	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.13	INTEGER	read-create	The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
INT pvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.5	INTEGER	read-create	802.1p default priority of the pvc.
STR pvcProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.6	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
STR pvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.8	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
VLA pvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.3	VlanIndex	read-only	Default VID of the pvc.
ROW pvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.7	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
STR pvcServiceName	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.12	DisplayString	read-create	Service name for paepvc.
STR pvcStateChannelType	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.8	DisplayString	read-only	The value of this object identifies the channel type at runtime.
STR pvcStateEncap	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.9	DisplayString	read-only	The value of this object identifies the channel encapsulation at runtime.
pvcStateEntry	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1		read-only	An entry in pvcStateTable.
INT pvcStatePriority	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.4	INTEGER	read-only	802.1p default priority of the pvc.
VLA pvcStatePvid	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.3	VlanIndex	read-only	Default VID of the pvc.
pvcStateTable	1.3.6.1.4.1.6321.1.2.3.1.8.4.3		read-only	This table show current PVC status.
INT pvcStateVci	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.2	INTEGER	read-only	VCI of the pvc.
INT pvcStateVpi	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.1	INTEGER	read-only	VPI of the pvc.
pvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.4.2		not-accessible	This table includes PVC configuration.
INT pvcUsRateLimit	1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.2	INTEGER	read-write	Upstream rate limit in Kbps for a PVC.
INT pvcUsRateLimitEnable	1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.1	INTEGER	read-write	Enable/disable upstream rate limit for a PVC.
pvcUsRateLimitEntry	1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1		not-accessible	An entry in pvcUsRateLimitTable.
pvcUsRateLimitTable	1.3.6.1.4.1.6321.1.2.3.1.8.4.4		not-accessible	This table defines the upstream rate limit for each PVC.
INT pvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.2	INTEGER	read-only	VCI of the pvc.
INT pvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.1	INTEGER	read-only	VPI of the pvc.
INT qryVid	1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.1	INTEGER	read-only	VLAN ID.
qryVidConfEntry	1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1		not-accessible	An entry in qryVidConfTable.
qryVidConfTable	1.3.6.1.4.1.6321.1.2.3.1.7.7.2		not-accessible	This table defines statically set VLANs used for response IGMP report.
ROW qryVidRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.2	RowStatus	read-create	This object indicates the status of this entry.
qryVidStatusEntry	1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1		not-accessible	An entry in qryVidStatusTable.
qryVidStatusTable	1.3.6.1.4.1.6321.1.2.3.1.7.7.3		not-accessible	This table shows statically set or dynamically learned VLANs used for response IGMP report.
INT qryVidType	1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1.1	INTEGER	read-only	VLAN type.
queryVid	1.3.6.1.4.1.6321.1.2.3.1.7.7
rpvc	1.3.6.1.4.1.6321.1.2.3.1.8.8
INT rpvcArpAgingTime	1.3.6.1.4.1.6321.1.2.3.1.8.8.4	INTEGER	read-write	Set RPVC ARP proxy aging time 10..10000 seconds, 0 to disable againg.
INT rpvcArpFlush	1.3.6.1.4.1.6321.1.2.3.1.8.8.5	INTEGER	read-write	Flush the RPVC ARP proxy table.
STR rpvcDSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.3	DisplayString	read-create	The down stream profile of the rpvc.
rpvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1		not-accessible	An entry in rpvcTable.
rpvcGatewayEntry	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1		not-accessible	An entry in Routed Gateway table.
IP rpvcGatewayIp	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.1	IpAddress	read-only	IP of RPVC gateway.
IP rpvcGatewayIpAddress	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.7	IpAddress	read-create	The gateway IP of rpvc.
INT rpvcGatewayPriority	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.4	INTEGER	read-write	802.1p p bit send to this RPVC gateway.
ROW rpvcGatewayRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.3	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
rpvcGatewayTable	1.3.6.1.4.1.6321.1.2.3.1.8.8.1		not-accessible	This table includes Routed Gateway configuration.
VLA rpvcGatewayVlanId	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.2	VlanIndex	read-write	Vlan id send to this RPVC gateway.
IP rpvcIp	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.5	IpAddress	read-only	The IP of the rpvc.
IP rpvcNetmask	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.6	IpAddress	read-only	The IP mask of the rpvc IP.
rpvcRouteDomainEntry	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1		not-accessible	An entry in rpvcRouteDomainTable.
IP rpvcRouteDomainIp	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.3	IpAddress	read-only	The route domain IP.
IP rpvcRouteDomainNetmask	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.4	IpAddress	read-only	The IP mask of the route domain IP.
ROW rpvcRouteDomainRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.5	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
rpvcRouteDomainTable	1.3.6.1.4.1.6321.1.2.3.1.8.8.3		not-accessible	This table includes RPVC route domain configuration.
INT rpvcRouteDomainVci	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.2	INTEGER	read-only	VCI of the rpvc.
INT rpvcRouteDomainVpi	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.1	INTEGER	read-only	VPI of the rpvc.
ROW rpvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.8	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
rpvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.8.2		not-accessible	This table includes RPVC configuration.
STR rpvcUSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.4	DisplayString	read-create	The up stream profile of the rpvc.
INT rpvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.2	INTEGER	read-only	VCI of the rpvc.
INT rpvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.1	INTEGER	read-only	VPI of the rpvc.
INT securedClientEnable	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.5	INTEGER	read-write	Enable/disable the entry.
IP securedClientEndIp	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.3	IpAddress	read-write	The ending IP address of the secured client set.
securedClientEntry	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1		not-accessible	A list of secured client entry.
INT securedClientIndex	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.1	INTEGER	read-only	The index of the entry.
INT securedClientService	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.4	INTEGER	read-write	Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1: telnet BIT 2: ftp BIT 3: web BIT 4: icmp BIT 5: not support BIT 6: snmp.
IP securedClientStartIp	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.2	IpAddress	read-write	The starting IP address of the secured client set.
securedClientTable	1.3.6.1.4.1.6321.1.2.3.1.11.5.2		not-accessible	A table that contains information about secured clients.
selt	1.3.6.1.4.1.6321.1.2.3.1.4.3
INT seltCableType	1.3.6.1.4.1.6321.1.2.3.1.4.3.4	INTEGER	read-only	The cable type that selt result indicates.
INT seltLoopEstimateLengthFt	1.3.6.1.4.1.6321.1.2.3.1.4.3.5	INTEGER	read-only	The estimated loop length that selt result indicates.
INT seltLoopEstimateLengthMeter	1.3.6.1.4.1.6321.1.2.3.1.4.3.6	INTEGER	read-only	The estimated loop length that selt result indicates.
INT seltOps	1.3.6.1.4.1.6321.1.2.3.1.4.3.2	INTEGER	read-write	The manager sets the object to 1 to start the selt and the agent clears the object to zero when selt is successfully completed.
STR seltStatus	1.3.6.1.4.1.6321.1.2.3.1.4.3.3	DisplayString	read-only	Status description of the selt result.
INT seltTarget	1.3.6.1.4.1.6321.1.2.3.1.4.3.1	INTEGER	read-write	IfIndex of the port which would be performed single end loopback test.
INT severityThresh	1.3.6.1.4.1.6321.1.2.3.1.2.4.1.1	INTEGER	read-write	The minimum alarm severity that is reported.
snrMgn	1.3.6.1.4.1.6321.1.2.3.1.8.15
snrMgnEntry	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1		not-accessible	An entry of snrMgnTable.
INT snrMgnMode	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.1	INTEGER	read-write	Configure DSL SNR margin configuration mode of the specified ports. Profile: the SNR margin configuration comes from DSL profile. Line: the SNR margin configuration comes from line configuration.
snrMgnTable	1.3.6.1.4.1.6321.1.2.3.1.8.15.1		not-accessible	A table containing the per port SNR Margin configuration.
INT snrMgnUcDownshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.5	INTEGER	read-write	Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
INT snrMgnUcMax	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.3	INTEGER	read-write	Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
INT snrMgnUcMin	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.4	INTEGER	read-write	Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
INT snrMgnUcTarget	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.2	INTEGER	read-write	Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
INT snrMgnUcUpshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.6	INTEGER	read-write	Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
INT snrMgnUrDownshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.10	INTEGER	read-write	Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
INT snrMgnUrMax	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.8	INTEGER	read-write	Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
INT snrMgnUrMin	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.9	INTEGER	read-write	Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
INT snrMgnUrTarget	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.7	INTEGER	read-write	Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
INT snrMgnUrUpshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.11	INTEGER	read-write	Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
statistics	1.3.6.1.4.1.6321.1.2.3.1.13
INT stdioTimeout	1.3.6.1.4.1.6321.1.2.3.1.11.12	INTEGER	read-write	Set the CLI/TELNET/WEB Session timeout, 0, or 1~300 minutes, 0 => disable.
subrPortEntry	1.3.6.1.4.1.6321.1.2.3.1.8.1.1		not-accessible	An entry in subrPortTable.
STR subrPortName	1.3.6.1.4.1.6321.1.2.3.1.8.1.1.1	DisplayString	read-write	Name of the subscriber.
subrPortTable	1.3.6.1.4.1.6321.1.2.3.1.8.1		not-accessible	This table includes subscriber attributes for the port.
STR subrPortTel	1.3.6.1.4.1.6321.1.2.3.1.8.1.1.2	DisplayString	read-write	Telephone number of the subscriber.
switch	1.3.6.1.4.1.6321.1.2.3.1.10
sys	1.3.6.1.4.1.6321.1.2.3.1.11
tlspvc	1.3.6.1.4.1.6321.1.2.3.1.8.11
tlspvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1		not-accessible	An entry of tlspvcTable.
STR tlspvcProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.6	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
STR tlspvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.8	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
ROW tlspvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.7	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
INT tlspvcSpriority	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.5	INTEGER	read-create	s-tag priority of the pvc.
VLA tlspvcSvid	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.3	VlanIndex	read-only	s-tag VLAN ID of the pvc.
tlspvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.11.1		not-accessible	This table includes Transparent LAN Service (TLS) PVC configuration.
INT tlspvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.2	INTEGER	read-only	VCI of the pvc.
INT tlspvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.1	INTEGER	read-only	VPI of the pvc.
trap	1.3.6.1.4.1.6321.1.2.3.1.12
usbCastCtrl	1.3.6.1.4.1.6321.1.2.3.1.11.10
INT usBcastCtrlEnable	1.3.6.1.4.1.6321.1.2.3.1.11.10.1	INTEGER	read-write	Enable/disable upstream broadcast control.
INT usBcastCtrlRate	1.3.6.1.4.1.6321.1.2.3.1.11.10.2	INTEGER	read-write	32~49984 in step of 32kbps
user	1.3.6.1.4.1.6321.1.2.3.1.11.9
INT userAuthDefaultPriviledge	1.3.6.1.4.1.6321.1.2.3.1.11.9.6	INTEGER	read-write	The user default priviledge to be assigned when radius authentication succeds but no user priviledge information(radius service-type) is provided.
INT userAuthMode	1.3.6.1.4.1.6321.1.2.3.1.11.9.1	INTEGER	read-write	User authentication procsssing mode.
IP userAuthServerIp	1.3.6.1.4.1.6321.1.2.3.1.11.9.2	IpAddress	read-write	The IP address of the authentication server.
INT userAuthServerPort	1.3.6.1.4.1.6321.1.2.3.1.11.9.3	INTEGER	read-write	The port of the authentication server.
OCT userAuthServerSecret	1.3.6.1.4.1.6321.1.2.3.1.11.9.4	OCTET STRING	read-write	The secret between the authentication server and the NE for authentication process.
userEntry	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1		not-accessible	An entry of userTable.
STR userName	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.1	DisplayString	read-only	The user name.
STR userPassword	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.2	DisplayString	read-create	The user password.
INT userPriviledge	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.3	INTEGER	read-create	The user priviledge to decide what operation the user can and cannot do.
ROW userRowStatus	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.4	RowStatus	read-create	The row status used to create or delete a user.
userTable	1.3.6.1.4.1.6321.1.2.3.1.11.9.5		not-accessible	A table that contains user information.
vlanIsolation	1.3.6.1.4.1.6321.1.2.3.1.10.12
vlanIsolationEntry	1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1		not-accessible	An entry of vlanIsolationTable.
ROW vlanIsolationRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1.1	RowStatus	read-create	Row status of the table used to create/delete an entry.
vlanIsolationTable	1.3.6.1.4.1.6321.1.2.3.1.10.12.1		not-accessible	A table contains configuration of isolated VLAN.

OID symbolic	OID numeric	Type	Access	Description
calixNetworks	1.3.6.1.4.1.6321
calixRegistrations	1.3.6.1.4.1.6321.1
calixProducts	1.3.6.1.4.1.6321.1.2
e5x100	1.3.6.1.4.1.6321.1.2.3
e5x110	1.3.6.1.4.1.6321.1.2.3.1
alarmconf	1.3.6.1.4.1.6321.1.2.3.1.2
INT alarmOps	1.3.6.1.4.1.6321.1.2.3.1.2.1	INTEGER	read-write	The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: clear BIT 2: cutoff
alarmConfTable	1.3.6.1.4.1.6321.1.2.3.1.2.2		not-accessible	This table includes alarm configuration.
alarmConfEntry	1.3.6.1.4.1.6321.1.2.3.1.2.2.1		not-accessible	An entry in alarmConfTable.
INT alarmConfId	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.1	INTEGER	read-only	5000:adslLine_up 5001:adslLine_down 5002:adslPerf_lol_thresh 5003:adslPerf_lof_thresh 5004:adslPerf_los_thresh 5005:adslPerf_lop_thresh 5006:adslPerf_es_thresh 5007:adslPerf_ses_thresh 5008:adslPerf_uas_thresh 5009:adslAtuc_loftrap 5010:adslAtuc_lostrap 5011:adslAtur_loftrap 5012:adslAtur_lostrap 5013:adslAtur_lprtrap 5014:ad_dhcp_rt_full 5015:ad_dhcp_dm_conflict 5016:ad_dhcp_entry_full 5017:ad_dhcp_ip_dup 5018:ad_dhcp_mac_dup 10000:eqptVol_err 10001:eqptEqpttemp_err 10002:eqptFan_err 10003:eqptHw_rtc_fail 10004:eqptHw_mon_fail 10005:eqptCold_start 10006:eqptWarm_start 10007:eqptAlm_input 10008:eqptI2c_err 10009:eqptAlm_input2 10010:eqptAlm_input3 15000:sysReboot 15001:sysAco 15002:sysAlm_clear 15003:sysLogin_fail 15004:sysAnti_spoofing 15005:sysAlm_svrty_change 20000:enetUp 20001:enetDown
INT alarmConfFacility	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.2	INTEGER	read-write	Alarm facility.
INT alarmConfTarget	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.3	INTEGER	read-write	The destination which alarms are reported to. Set the bit to 1 to enable the target. BIT 1: snmp trap BIT 2: syslog
INT alarmConfSeverity	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.4	INTEGER	read-write	Alarm severity
INT alarmConfClearable	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.5	INTEGER	read-write	Setting the object to one indicates that the alarm is to be cleared when user submits alarm clear.
alarmCurrTable	1.3.6.1.4.1.6321.1.2.3.1.2.3		not-accessible	This table includes current alarm information.
alarmCurrEntry	1.3.6.1.4.1.6321.1.2.3.1.2.3.1		not-accessible	An entry in alarmCurrTable.
INT alarmCurrIndex	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.1	INTEGER	read-only	Index of the alarm.
TIK alarmCurrOccurTime	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.2	TimeTicks	read-only	Alarm occurence time (in hundredths of a second) since the system was last re-initialized.
OID alarmCurrTrapOid	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.3	OBJECT IDENTIFIER	read-only	Trap OID of the alarm.
INT alarmCurrParam1	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.4	INTEGER	read-only	The 1st parameter of the alarm.
INT alarmCurrParam2	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.5	INTEGER	read-only	The 2nd parameter of the alarm.
INT alarmCurrParam3	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.6	INTEGER	read-only	The 3rd parameter of the alarm.
INT alarmCurrParam4	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.7	INTEGER	read-only	The 4th parameter of the alarm.
INT alarmCurrParam5	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.8	INTEGER	read-only	The 5th parameter of the alarm.
INT alarmCurrParam6	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.9	INTEGER	read-only	The 6th parameter of the alarm.
INT alarmCurrParam7	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.10	INTEGER	read-only	The 7th parameter of the alarm.
INT alarmCurrParam8	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.11	INTEGER	read-only	The 8th parameter of the alarm.
STR alarmCurrTimeDescr	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.12	DisplayString	read-only	The string representation of occurence time (YYYY/MM/DD HH:MM:SS).
INT alarmCurrSeverity	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.13	INTEGER	read-only	The severity of the alarm.
STR alarmCurrDescr	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.14	DisplayString	read-only	The description of the alarm.
alarmSeverityPortTable	1.3.6.1.4.1.6321.1.2.3.1.2.4		not-accessible	This table includes the configuration of alarm reporting severity threshold for each port.
alarmSeverityPortEntry	1.3.6.1.4.1.6321.1.2.3.1.2.4.1		not-accessible	An entry in alarmSeverityPortTable.
INT severityThresh	1.3.6.1.4.1.6321.1.2.3.1.2.4.1.1	INTEGER	read-write	The minimum alarm severity that is reported.
diagnostic	1.3.6.1.4.1.6321.1.2.3.1.4
selt	1.3.6.1.4.1.6321.1.2.3.1.4.3
INT seltTarget	1.3.6.1.4.1.6321.1.2.3.1.4.3.1	INTEGER	read-write	IfIndex of the port which would be performed single end loopback test.
INT seltOps	1.3.6.1.4.1.6321.1.2.3.1.4.3.2	INTEGER	read-write	The manager sets the object to 1 to start the selt and the agent clears the object to zero when selt is successfully completed.
STR seltStatus	1.3.6.1.4.1.6321.1.2.3.1.4.3.3	DisplayString	read-only	Status description of the selt result.
INT seltCableType	1.3.6.1.4.1.6321.1.2.3.1.4.3.4	INTEGER	read-only	The cable type that selt result indicates.
INT seltLoopEstimateLengthFt	1.3.6.1.4.1.6321.1.2.3.1.4.3.5	INTEGER	read-only	The estimated loop length that selt result indicates.
INT seltLoopEstimateLengthMeter	1.3.6.1.4.1.6321.1.2.3.1.4.3.6	INTEGER	read-only	The estimated loop length that selt result indicates.
multicast	1.3.6.1.4.1.6321.1.2.3.1.7
INT igmpEnable	1.3.6.1.4.1.6321.1.2.3.1.7.1	INTEGER	read-write	Enable/disable IGMP protocol.
mcastBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4
INT mcastDefaultBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4.1	INTEGER	read-write	Default bandwidth requirement for a multicast channel.
INT maxNumOfMcastBw	1.3.6.1.4.1.6321.1.2.3.1.7.4.2	INTEGER	read-only	The maximum number of row entries that user can create in mcastBwTable.
mcastBwTable	1.3.6.1.4.1.6321.1.2.3.1.7.4.3		not-accessible	This table defines bandwidth budget for a range of multicast IP channels.
mcastBwEntry	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1		not-accessible	An entry of mcastBwTable.
INT mcastBwIndex	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.1	INTEGER	read-only	The index which specify the entry.
IP mcastBwStartIp	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.2	IpAddress	read-only	The start multicast IP of the bandwidth control range.
IP mcastBwEndIp	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.3	IpAddress	read-only	The end multicast IP of the bandwidth control range.
INT mcastBwBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.4	INTEGER	read-create	The bandwidth budget for the multicast IP channels.
ROW mcastBwRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.5	RowStatus	read-create	The row status of the entry.
mcastBwPortTable	1.3.6.1.4.1.6321.1.2.3.1.7.4.4		not-accessible	This table specify the multicast bandwidth control of the port.
mcastBwPortEntry	1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1		not-accessible	An entry of mcastBwPortTable.
INT mcastBwPortEnable	1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.1	INTEGER	read-write	Enable/disable multicast bandwidth control for a port.
INT mcastBwPortBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.2	INTEGER	read-write	Set bandwidth threshold for a port.
igmpCount	1.3.6.1.4.1.6321.1.2.3.1.7.5
igmpCountPortTable	1.3.6.1.4.1.6321.1.2.3.1.7.5.1		not-accessible	This table specify the IGMP count limiting of the port.
igmpCountPortEntry	1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1		not-accessible	An entry of igmpCountPortTable.
INT igmpCountPortEnable	1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.1	INTEGER	read-write	Enable/disable IGMP count limiting for a port.
INT igmpCountPortLimit	1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.2	INTEGER	read-write	The maximum allowed IGMP report count for a port.
mvlan	1.3.6.1.4.1.6321.1.2.3.1.7.6
INT maxNumOfMvlan	1.3.6.1.4.1.6321.1.2.3.1.7.6.1	INTEGER	read-only	The maximum number of row entries that user can create in mvlanTable.
mvlanTable	1.3.6.1.4.1.6321.1.2.3.1.7.6.2		not-accessible	A table containing static configuration information for each multicast VLAN configured into the device.
mvlanEntry	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1		not-accessible	An entry of mvlanTable.
VLA mvlanIndex	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.1	VlanIndex	read-only	The VLAN-ID refering to this VLAN.
STR mvlanName	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.2	DisplayString	read-create	An administratively assigned string, which may be used to identify the VLAN.
POR mvlanEgressPorts	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.3	PortList	read-create	The set of ports which are permanently assigned to the egress list for this multicast VLAN.
POR mvlanUntaggedPorts	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.4	PortList	read-create	The set of ports which should transmit egress packets for this multicast VLAN as untagged.
ROW mvlanRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.5	RowStatus	read-create	This object indicates the status of this entry.
mvlanTranslateTable	1.3.6.1.4.1.6321.1.2.3.1.7.6.3		not-accessible	A table that contains multicast to VLAN translation.
mvlanTranslateEntry	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1		not-accessible	An entry of mvlanTranslateTable.
INT mvlanTranslateIndex	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.1	INTEGER	read-only	The index which specif the entry.
IP mvlanTranslateStartIp	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.2	IpAddress	read-write	The start IP of the multicast VLAN translation.
IP mvlanTranslateEndIp	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.3	IpAddress	read-write	The end IP of the multicast VLAN translation.
queryVid	1.3.6.1.4.1.6321.1.2.3.1.7.7
INT maxNumOfQryVid	1.3.6.1.4.1.6321.1.2.3.1.7.7.1	INTEGER	read-only	The maximum number of row entries that user can create in qryVidConfTable.
qryVidConfTable	1.3.6.1.4.1.6321.1.2.3.1.7.7.2		not-accessible	This table defines statically set VLANs used for response IGMP report.
qryVidConfEntry	1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1		not-accessible	An entry in qryVidConfTable.
INT qryVid	1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.1	INTEGER	read-only	VLAN ID.
ROW qryVidRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.2	RowStatus	read-create	This object indicates the status of this entry.
qryVidStatusTable	1.3.6.1.4.1.6321.1.2.3.1.7.7.3		not-accessible	This table shows statically set or dynamically learned VLANs used for response IGMP report.
qryVidStatusEntry	1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1		not-accessible	An entry in qryVidStatusTable.
INT qryVidType	1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1.1	INTEGER	read-only	VLAN type.
INT igmpVersion	1.3.6.1.4.1.6321.1.2.3.1.7.9	INTEGER	read-write	Setting IGMP version.
INT igmpLeaveMode	1.3.6.1.4.1.6321.1.2.3.1.7.10	INTEGER	read-write	Configure IGMP leave message handling mode.
igmpTimer	1.3.6.1.4.1.6321.1.2.3.1.7.11
INT igmpQryInterval	1.3.6.1.4.1.6321.1.2.3.1.7.11.1	INTEGER	read-write	Set IGMP query interval, 10~1000 in seconds.
INT igmpRobust	1.3.6.1.4.1.6321.1.2.3.1.7.11.2	INTEGER	read-write	Set IGMP query Robustness, 1~5.
INT igmpQryRespInterval	1.3.6.1.4.1.6321.1.2.3.1.7.11.3	INTEGER	read-write	Set IGMP query response interval, 1~100 in 100 milliseconds.
INT igmpLastMemQryInterval	1.3.6.1.4.1.6321.1.2.3.1.7.11.4	INTEGER	read-write	Set IGMP Last Member Query interval, 1~5 in 100 milliseconds.
INT igmpLastMemQryRobust	1.3.6.1.4.1.6321.1.2.3.1.7.11.5	INTEGER	read-write	Set Last Member Query Robustness, 1~5.
auditQuery	1.3.6.1.4.1.6321.1.2.3.1.7.12
INT auditQryEnable	1.3.6.1.4.1.6321.1.2.3.1.7.12.1	INTEGER	read-write	Enable/disable IGMP audit query.
INT auditQryInterval	1.3.6.1.4.1.6321.1.2.3.1.7.12.2	INTEGER	read-write	Set IGMP Audit Query Interval, 1~4 in 100 milliseconds.
INT auditQryRobust	1.3.6.1.4.1.6321.1.2.3.1.7.12.3	INTEGER	read-write	Set IGMP Audit Query Robustness, 1~5.
igmpProfile	1.3.6.1.4.1.6321.1.2.3.1.7.13
INT maxNumberOfIgmpProfiles	1.3.6.1.4.1.6321.1.2.3.1.7.13.1	INTEGER	read-only	The max number of IGMP profiles in the system.
igmpProfileTable	1.3.6.1.4.1.6321.1.2.3.1.7.13.2		not-accessible	A table that contains IGMP Profiles.
igmpProfileEntry	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1		not-accessible	The entry of IGMP Profile table.
STR igmpProfileName	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.1	DisplayString	read-only	The IGMP Profile name.
INT igmpProfileEnable	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.2	INTEGER	read-write	Enable/disable IGMP Profile.
INT igmpProfileMaxGroup	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.3	INTEGER	read-write	Set maximum allowed multicast group, 1~16.
ROW igmpProfileRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.4	RowStatus	read-create	The row status of the IGMP Profile entry.
igmpFilterTable	1.3.6.1.4.1.6321.1.2.3.1.7.13.3		not-accessible	A table that contains IGMP Filters.
igmpFilterEntry	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1		not-accessible	The entry of IGMP Filter table.
INT igmpFilterIndex	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.1	INTEGER	read-only	The index which specifies the filter rule.
IP igmpFilterStartIp	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.2	IpAddress	read-create	The start IP of the filter rule.
IP igmpFilterEndIp	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.3	IpAddress	read-create	The end IP of the filter rule.
igmpProfilePortTable	1.3.6.1.4.1.6321.1.2.3.1.7.13.4		not-accessible	This table specifies the IGMP Profile of the port.
igmpProfilePortEntry	1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1		not-accessible	An entry in igmpProfilePortTable.
OCT igmpProfilePortProfile	1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1.1	OCTET STRING	read-write	The IGMP Profile of the port.
port	1.3.6.1.4.1.6321.1.2.3.1.8
subrPortTable	1.3.6.1.4.1.6321.1.2.3.1.8.1		not-accessible	This table includes subscriber attributes for the port.
subrPortEntry	1.3.6.1.4.1.6321.1.2.3.1.8.1.1		not-accessible	An entry in subrPortTable.
STR subrPortName	1.3.6.1.4.1.6321.1.2.3.1.8.1.1.1	DisplayString	read-write	Name of the subscriber.
STR subrPortTel	1.3.6.1.4.1.6321.1.2.3.1.8.1.1.2	DisplayString	read-write	Telephone number of the subscriber.
adslPort	1.3.6.1.4.1.6321.1.2.3.1.8.2
adslLineConfTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.1		not-accessible	This table includes common attributes describing the ADSL line.
adslLineConfEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1		not-accessible	An entry in adslLineConfTable.
INT adslLineConfAdslMode	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.1	INTEGER	read-write	G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
INT adslLineConfAnnexL	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.2	INTEGER	read-write	Enable/disable annex L for the port(Only in AnnexA).
INT adslLineConfAnnexM	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.3	INTEGER	read-write	Enable/disable annex M for the port(For BCM AnnexA solution).
INT adslLineConfAnnexI	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.4	INTEGER	read-write	Enable/disable annex I for the port(For BCM AnnexA solution).
INT adslLineConfOptionMask	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.5	INTEGER	read-write	The semantic for each bit is: BIT 1 : Disable Trellis BIT 2 : Disable Reed-Solomon BIT 3 : Disable upstream bitswap BIT 4 : Disable downstream bitswap BIT 5 : Disable 1-bit constellation BIT 6 : Disable transmit windowing BIT 7 : Disable s=0.5 support (ADSL1 only) BIT 8 : Disable G.lite rate limit (ADSL1 only) BIT 9 : Enable Nitro BIT 10: Enable US PHYR BIT 11: ENABLE DS PHYR
INT adslLineConfPowerMgmt	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.6	INTEGER	read-write	Enable/disable power management for the port.
INT adslLineConfPowerMode	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.7	INTEGER	read-write	The power mode of the ADSL line.
INT adslLineConfAturMaxTxPower	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.8	INTEGER	read-write	The maximum allowed transmit power of ATU-R.
INT adslLineConfAtucMaxTxPower	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.9	INTEGER	read-write	The maximum allowed transmit power of ATU-C.
INT adslLineConfMaxRxPower	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.10	INTEGER	read-write	The maximum aggregate received power.
OCT adslLineConfAturCarrierMask	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.11	OCTET STRING	read-write	The upstream carrier mask. For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off.
OCT adslLineConfAtucCarrierMask0	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.12	OCTET STRING	read-write	The downstream carrier mask. For CTLM AnnexA solution, bin is from 32 to 255; CTLM AnnexB solution, bin is from 64 to 255; BCM solution, bin is from 32 to 255. Bit set to 1 indicates the bin is masked off.
OCT adslLineConfAtucCarrierMask1	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.13	OCTET STRING	read-write	The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
INT adslLineConfAturInp	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.14	INTEGER	read-write	The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslLineConfAtucInp	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.15	INTEGER	read-write	The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslLineConfL0Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.16	INTEGER	read-write	Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslLineConfL2Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.17	INTEGER	read-write	Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslLineConfL2ATPR	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.18	INTEGER	read-write	Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslLineConfL2ATPRT	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.19	INTEGER	read-write	the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslLineConfMaxL2Rate	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.20	INTEGER	read-write	configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
INT adslLineConfMinL2Rate	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.21	INTEGER	read-write	configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
INT adslLineConfL0toL2Rate	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.22	INTEGER	read-write	configured transition L0 to L2 rate. (= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
INT adslLineConfNitro	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.23	INTEGER	read-write	Enable/disable nitro mode for the port(For BCM solution).
INT adslLineConfUSPhyr	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.24	INTEGER	read-write	Enable/disable Upstream PHYR for the port(For BCM solution).
INT adslLineConfDSPhyr	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.25	INTEGER	read-write	Enable/disable Downstream PHYR for the port(For BCM solution).
adslPortBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3
OCT adslPortTarget	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.1	OCTET STRING	read-write	The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chaises) Byte 2~3: 0,0 Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
INT adslPortOps	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.2	INTEGER	read-write	The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: set ADSL mode BIT 4: set line profile BIT 5: set alarm profile BIT 6: enable Annex L to be narrow mode(Only in AnnexA) BIT 7: enable Annex L to be wide mode(Only in AnnexA) BIT 8: disable Annex L(Only in AnnexA) BIT 9: enable Annex M (For BCM AnnexA solution) BIT 10: disable Annex M (For BCM AnnexA solution) BIT 11: enable Annex I (For BCM AnnexA solution) BIT 12: disable Annex I (For BCM AnnexA solution) BIT 13: set option mask BIT 14: enable power management mode to be L2 BIT 15: enable power management mode to be L2 BIT 16: disable power management mode BIT 17: set power mode to be fixed BIT 18: set power mode to be priority to power BIT 19: set power mode to be priority to rate BIT 20: set ATU-R max Tx power BIT 21: set ATU-C max Tx power BIT 22: set max Rx power BIT 23: set ATU-R carrier mask BIT 24: set ATU-C carrier mask BIT 25: set ATU-R INP minimum setting BIT 26: set ATU-C INP minimum setting
INT adslPortOps2	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.3	INTEGER	read-write	The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: set L0 Time BIT 2: set L2 Time BIT 3: set L2 ATPR BIT 4: set L2 ATPRT BIT 5: set maximum L2 rate BIT 6: set minimum L2 rate BIT 7: set transition L0 to L2 rate
INT adslModeForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.4	INTEGER	read-write	G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
STR adslLineProfileForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.5	DisplayString	read-write	The ADSL line profile.
STR adslAlarmProfileForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.6	DisplayString	read-write	The ADSL alarm profile.
INT adslOptionMaskForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.7	INTEGER	read-write	The semantic for each bit is identical to the object adslLineConfOptionMask.
INT adslAturMaxTxPowerForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.8	INTEGER	read-write	The maximum allowed transmit power of ATU-R.
INT adslAtucMaxTxPowerForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.9	INTEGER	read-write	The maximum allowed transmit power of ATU-C.
INT adslMaxRxPowerForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.10	INTEGER	read-write	The maximum aggregate received power.
OCT adslAturCarrierMaskForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.11	OCTET STRING	read-write	The upstream carrier mask.For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off.
OCT adslAtucCarrierMask0ForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.12	OCTET STRING	read-write	The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates the bin is masked off.
OCT adslAtucCarrierMask1ForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.13	OCTET STRING	read-write	The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
INT adslAturInpForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.14	INTEGER	read-write	The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslAtucInpForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.15	INTEGER	read-write	The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslL0TimeForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.16	INTEGER	read-write	Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslL2TimeForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.17	INTEGER	read-write	Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslL2ATPRForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.18	INTEGER	read-write	Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslL2ATPRTForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.19	INTEGER	read-write	the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslMaxL2RateForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.20	INTEGER	read-write	configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
INT adslMinL2RateForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.21	INTEGER	read-write	configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
INT adslL0toL2RateForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.22	INTEGER	read-write	configured transition L0 to L2 rate. (= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
adslLineStatusTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.4		not-accessible	This table includes the ADSL line status.
adslLineStatusEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1		not-accessible	An entry in adslLineStatusTable.
INT adslLineStatusMode	1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.1	INTEGER	read-only	The link up mode of the ADSL line.
INT adslLineUpTime	1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.2	INTEGER	read-only	The link up time of the ADSL line, in unit of seconds
powerMgmtParamTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.5		not-accessible	This table defines L0 to L2 power transition parameters.
powerMgmtParamEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1		not-accessible	An entry in powerMgmtParamTable.
INT powerMgmtL0Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.1	INTEGER	read-write	The object specifies the minimum time in L0 mode before L2 mode may be entered.
INT powerMgmtL2Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.2	INTEGER	read-write	The object specifies the minimum time in L2 mode before trimming and in between power trims.
INT powerMgmtL2Atpr	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.3	INTEGER	read-write	The maximum Aggregate Transmit Power Reduction.
INT powerMgmtL2Atprt	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.4	INTEGER	read-write	The maximum Aggregate Transmit Power Reduction Total.
INT powerMgmtL2MinRate	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.5	INTEGER	read-write	The object specifies the minimum L2 rate.
INT powerMgmtL2MaxRate	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.6	INTEGER	read-write	The object specifies the maximum L2 rate.
INT powerMgmtL2ThreshRate	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.7	INTEGER	read-write	The object specifies the rate threshold that triggers the line entering L0 or L2 mode.
powerMgmtPSDTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.6		not-accessible	This table provides the PSD setting for both ATU-C and ATU-R.
powerMgmtPSDEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1		not-accessible	An entry in powerMgmtPSDTable.
INT powerMgmtAtucMaxPSD	1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.1	INTEGER	read-write	The object specifies the maximum ATU-C PSD.
INT powerMgmtAturMaxPSD	1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.2	INTEGER	read-write	The object specifies the maximum ATU-R PSD.
pvc	1.3.6.1.4.1.6321.1.2.3.1.8.4
INT maxNumOfPvcs	1.3.6.1.4.1.6321.1.2.3.1.8.4.1	INTEGER	read-only	The maximum number of PVCs which could be created on a port.
pvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.4.2		not-accessible	This table includes PVC configuration.
pvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1		not-accessible	An entry in pvcTable.
INT pvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.1	INTEGER	read-only	VPI of the pvc.
INT pvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.2	INTEGER	read-only	VCI of the pvc.
VLA pvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.3	VlanIndex	read-only	Default VID of the pvc.
INT pvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.5	INTEGER	read-create	802.1p default priority of the pvc.
STR pvcProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.6	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
ROW pvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.7	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
STR pvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.8	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
STR pvcAcName	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.11	DisplayString	read-create	Access concentrator name for paepvc.
STR pvcServiceName	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.12	DisplayString	read-create	Service name for paepvc.
INT pvcHelloTime	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.13	INTEGER	read-create	The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
pvcStateTable	1.3.6.1.4.1.6321.1.2.3.1.8.4.3		read-only	This table show current PVC status.
pvcStateEntry	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1		read-only	An entry in pvcStateTable.
INT pvcStateVpi	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.1	INTEGER	read-only	VPI of the pvc.
INT pvcStateVci	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.2	INTEGER	read-only	VCI of the pvc.
VLA pvcStatePvid	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.3	VlanIndex	read-only	Default VID of the pvc.
INT pvcStatePriority	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.4	INTEGER	read-only	802.1p default priority of the pvc.
STR pvcStateChannelType	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.8	DisplayString	read-only	The value of this object identifies the channel type at runtime.
STR pvcStateEncap	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.9	DisplayString	read-only	The value of this object identifies the channel encapsulation at runtime.
pvcUsRateLimitTable	1.3.6.1.4.1.6321.1.2.3.1.8.4.4		not-accessible	This table defines the upstream rate limit for each PVC.
pvcUsRateLimitEntry	1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1		not-accessible	An entry in pvcUsRateLimitTable.
INT pvcUsRateLimitEnable	1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.1	INTEGER	read-write	Enable/disable upstream rate limit for a PVC.
INT pvcUsRateLimit	1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.2	INTEGER	read-write	Upstream rate limit in Kbps for a PVC.
ppvc	1.3.6.1.4.1.6321.1.2.3.1.8.5
INT maxNumOfPriorityPvcs	1.3.6.1.4.1.6321.1.2.3.1.8.5.1	INTEGER	read-only	The maximum number of priority PVCs which could be created on a port.
ppvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.5.2		not-accessible	This table includes priority PVC configuration.
ppvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1		not-accessible	An entry in ppvcTable.
INT ppvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.1	INTEGER	read-only	VPI of the ppvc.
INT ppvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.2	INTEGER	read-only	VCI of the ppvc.
VLA ppvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.3	VlanIndex	read-only	Default VID of the ppvc.
INT ppvcEncap	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.4	INTEGER	read-create	Encapsulation of the ppvc.
INT ppvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.5	INTEGER	read-create	802.1p default priority of the ppvc.
ROW ppvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.6	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ppvcMemberTable	1.3.6.1.4.1.6321.1.2.3.1.8.5.4		not-accessible	This table includes priority PVC member configuration.
ppvcMemberEntry	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1		not-accessible	An entry in ppvcMemberTable.
INT ppvcMemberVpi	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.1	INTEGER	read-only	VPI of the member ppvc.
INT ppvcMemberVci	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.2	INTEGER	read-only	VCI of the member ppvc.
INT ppvcMemberPriority	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.3	INTEGER	read-only	802.1p default priority of the member ppvc.
STR ppvcMemberProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.4	DisplayString	read-create	The profile of the member ppvc in DS side.
ROW ppvcMemberRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.5	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
STR ppvcMemberProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.6	DisplayString	read-create	The profile of the member ppvc in US side.
rpvc	1.3.6.1.4.1.6321.1.2.3.1.8.8
rpvcGatewayTable	1.3.6.1.4.1.6321.1.2.3.1.8.8.1		not-accessible	This table includes Routed Gateway configuration.
rpvcGatewayEntry	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1		not-accessible	An entry in Routed Gateway table.
IP rpvcGatewayIp	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.1	IpAddress	read-only	IP of RPVC gateway.
VLA rpvcGatewayVlanId	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.2	VlanIndex	read-write	Vlan id send to this RPVC gateway.
ROW rpvcGatewayRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.3	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
INT rpvcGatewayPriority	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.4	INTEGER	read-write	802.1p p bit send to this RPVC gateway.
rpvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.8.2		not-accessible	This table includes RPVC configuration.
rpvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1		not-accessible	An entry in rpvcTable.
INT rpvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.1	INTEGER	read-only	VPI of the rpvc.
INT rpvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.2	INTEGER	read-only	VCI of the rpvc.
STR rpvcDSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.3	DisplayString	read-create	The down stream profile of the rpvc.
STR rpvcUSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.4	DisplayString	read-create	The up stream profile of the rpvc.
IP rpvcIp	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.5	IpAddress	read-only	The IP of the rpvc.
IP rpvcNetmask	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.6	IpAddress	read-only	The IP mask of the rpvc IP.
IP rpvcGatewayIpAddress	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.7	IpAddress	read-create	The gateway IP of rpvc.
ROW rpvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.8	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
rpvcRouteDomainTable	1.3.6.1.4.1.6321.1.2.3.1.8.8.3		not-accessible	This table includes RPVC route domain configuration.
rpvcRouteDomainEntry	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1		not-accessible	An entry in rpvcRouteDomainTable.
INT rpvcRouteDomainVpi	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.1	INTEGER	read-only	VPI of the rpvc.
INT rpvcRouteDomainVci	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.2	INTEGER	read-only	VCI of the rpvc.
IP rpvcRouteDomainIp	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.3	IpAddress	read-only	The route domain IP.
IP rpvcRouteDomainNetmask	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.4	IpAddress	read-only	The IP mask of the route domain IP.
ROW rpvcRouteDomainRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.5	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
INT rpvcArpAgingTime	1.3.6.1.4.1.6321.1.2.3.1.8.8.4	INTEGER	read-write	Set RPVC ARP proxy aging time 10..10000 seconds, 0 to disable againg.
INT rpvcArpFlush	1.3.6.1.4.1.6321.1.2.3.1.8.8.5	INTEGER	read-write	Flush the RPVC ARP proxy table.
dsBcastDisableTable	1.3.6.1.4.1.6321.1.2.3.1.8.9		not-accessible	This table includes Down Stream Bcast configuration.
dsBcastDisableEntry	1.3.6.1.4.1.6321.1.2.3.1.8.9.1		not-accessible	An entry in Down Stream Bcast table.
INT dsBcastDisableVlanId	1.3.6.1.4.1.6321.1.2.3.1.8.9.1.1	INTEGER	read-only	downstream broadcast disabled vid.
ROW dsBcastDisableRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.9.1.2	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
paepvc	1.3.6.1.4.1.6321.1.2.3.1.8.10
paepvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.10.1		not-accessible	This table includes PPPoAoE PVC configuration.
paepvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1		not-accessible	An entry of paepvcTable.
INT paepvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.1	INTEGER	read-only	VPI of the pvc.
INT paepvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.2	INTEGER	read-only	VCI of the pvc.
VLA paepvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.3	VlanIndex	read-only	Default VID of the pvc.
INT paepvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.5	INTEGER	read-create	802.1p default priority of the pvc.
STR paepvcProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.6	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
STR paepvcAcName	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.7	DisplayString	read-create	Access concentrator name.
STR paepvcServiceName	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.8	DisplayString	read-create	Service name.
INT paepvcHelloTime	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.9	INTEGER	read-create	The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
ROW paepvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.10	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
STR paepvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.11	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
VLA paepvcCvid	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.12	VlanIndex	read-create	Default C-VID of the pvc.
INT paepvcCPriority	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.13	INTEGER	read-create	802.1p default C-priority of the pvc.
tlspvc	1.3.6.1.4.1.6321.1.2.3.1.8.11
tlspvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.11.1		not-accessible	This table includes Transparent LAN Service (TLS) PVC configuration.
tlspvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1		not-accessible	An entry of tlspvcTable.
INT tlspvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.1	INTEGER	read-only	VPI of the pvc.
INT tlspvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.2	INTEGER	read-only	VCI of the pvc.
VLA tlspvcSvid	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.3	VlanIndex	read-only	s-tag VLAN ID of the pvc.
INT tlspvcSpriority	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.5	INTEGER	read-create	s-tag priority of the pvc.
STR tlspvcProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.6	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
ROW tlspvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.7	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
STR tlspvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.8	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
ipbpvc	1.3.6.1.4.1.6321.1.2.3.1.8.12
ipbpvcDomainTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.1		not-accessible	This table includes ipbpvc domain configuration. This table is supported by R3.00 and later versions.
ipbpvcDomainEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1		not-accessible	An entry of ipbpvcDomainTable.
OCT ipbpvcDomainName	1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.1	OCTET STRING	read-only	Name of the domain.
ROW ipbpvcDomainRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.2	RowStatus	read-create	Row status of the table.
ipbpvcDomainVlanTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.2		not-accessible	This table includes ipbpvc domain VLAN configuration. This table is supported by R3.00 and later versions.
ipbpvcDomainVlanEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1		not-accessible	An entry of ipbpvcDomainVlanTable.
VLA ipbpvcDomainVlanId	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.1	VlanIndex	read-only	Set VLAN to join or leave the specified domain.
INT ipbpvcDomainDhcpVlanEnable	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.2	INTEGER	read-create	Enable/disable DHCP VLAN in a domain.
ROW ipbpvcDomainVlanRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.3	RowStatus	read-create	Row status of the table used to create/delete an entry.
ipbpvcEdgeRouterTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.3		not-accessible	This table includes ipbpvc edge router configuration. This table is supported by R3.00 and later versions.
ipbpvcEdgeRouterEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1		not-accessible	An entry of ipbpvcEdgeRouterTable.
IP ipbpvcEdgeRouterIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.1	IpAddress	read-only	IP address of the edge router.
VLA ipbpvcEdgeRouterVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.2	VlanIndex	read-only	VLAN ID of the edge router.
INT ipbpvcEdgeRouterMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.3	INTEGER	read-only	Netmask of the edge router.
ROW ipbpvcEdgeRouterRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.4	RowStatus	read-create	Row status of the table used to create/delete an entry.
ipbpvcInterfaceTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.4		not-accessible	This table includes ipbpvc interface configuration. This table is supported by R3.00 and later versions.
ipbpvcInterfaceEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1		not-accessible	An entry of ipbpvcInterfaceTable.
IP ipbpvcInterfaceIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.1	IpAddress	read-only	IP address of the interface.
INT ipbpvcInterfaceMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.2	INTEGER	read-only	Netmask of the interface.
VLA ipbpvcInterfaceVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.3	VlanIndex	read-only	VLAN ID of the interface.
INT ipbpvcInterfaceIfIndex	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.4	INTEGER	read-create	IfIndex of the interface.
INT ipbpvcInterfaceVpi	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.5	INTEGER	read-create	VPI of the interface.
INT ipbpvcInterfaceVci	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.6	INTEGER	read-create	VCI of the interface.
ROW ipbpvcInterfaceRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.7	RowStatus	read-create	Row status of the table used to create/delete an entry.
ipbpvcRouteTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.5		not-accessible	This table includes ipbpvc route configuration. This table is supported by R3.00 and later versions.
ipbpvcRouteEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1		not-accessible	An entry of ipbpvcRouteTable.
IP ipbpvcRouteIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.1	IpAddress	read-only	IP address of the route.
INT ipbpvcRouteMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.2	INTEGER	read-only	Netmask of the route.
IP ipbpvcRouteNextHop	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.3	IpAddress	read-only	Next hop IP address of the route.
INT ipbpvcRouteMetric	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.4	INTEGER	read-create	Metric of the route.
INT ipbpvcRoutePriority	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.5	INTEGER	read-create	Priority of the route. Note that the default value of this object is 8, which means we keep the original priority of the packet(frame).
ROW ipbpvcRouteRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.6	RowStatus	read-create	Row status of the table used to create/delete an entry.
ipbpvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.6		not-accessible	This table includes ipbpvc configuration. This table is supported by R3.00 and later versions.
ipbpvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1		not-accessible	An entry of ipbpvcTable.
INT ipbpvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.1	INTEGER	read-only	VPI of the PVC.
INT ipbpvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.2	INTEGER	read-only	VCI of the PVC.
INT ipbpvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.3	INTEGER	read-only	PVID of the PVC.
INT ipbpvcEncap	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.4	INTEGER	read-create	Type of the PVC.
INT ipbpvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.5	INTEGER	read-create	Priority of the PVC.
OCT ipbpvcProfile	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.6	OCTET STRING	read-create	Profile of the PVC.
INT ipbpvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.7	INTEGER	read-create	Row status of the table used to create/delete an entry.
OCT ipbpvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.8	OCTET STRING	read-create	US Profile of the PVC.
arpproxy	1.3.6.1.4.1.6321.1.2.3.1.8.12.8
INT arpproxyAge	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.1	INTEGER	read-write	Aging time of the ARP proxy. This object is supported by R3.00 and later versions.
arpproxyFlush	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2
INT arpproxyFlushTarget	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.1	INTEGER	read-write	The target whose ARP table to be flushed. This object is supported by R3.00 and later versions.
INT arpproxyFlushOps	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.2	INTEGER	read-write	Set the object to 1 to start flushing. This object is supported by R3.00 and later versions.
IP arpproxyFlushEdgeRouterIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.3	IpAddress	read-write	Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
VLA arpproxyFlushEdgeRouterVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.4	VlanIndex	read-write	Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
IP arpproxyFlushInterfaceIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.5	IpAddress	read-write	Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
INT arpproxyFlushInterfaceMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.6	INTEGER	read-write	Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
VLA arpproxyFlushInterfaceVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.7	VlanIndex	read-write	Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
dtpvc	1.3.6.1.4.1.6321.1.2.3.1.8.14
dtpvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.14.1		not-accessible	This table includes Double Tagging (DT) PVC configuration.
dtpvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1		not-accessible	An entry of dtpvcTable.
INT dtpvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.1	INTEGER	read-only	VPI of the pvc.
INT dtpvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.2	INTEGER	read-only	VCI of the pvc.
VLA dtpvcSvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.3	VlanIndex	read-only	s-tag VLAN ID of the pvc.
INT dtpvcSpriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.4	INTEGER	read-create	s-tag priority of the pvc.
VLA dtpvcCvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.5	VlanIndex	read-create	c-tag VLAN ID of the pvc.
INT dtpvcCpriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.6	INTEGER	read-create	c-tag priority of the pvc.
STR dtpvcDSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.7	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in DS side.
STR dtpvcUSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.8	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in US side.
ROW dtpvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.9	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
INT dtpvcSuperChannel	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.10	INTEGER	read-create	Specified the configured DTPVC is a super channel.
STR dtpvcAcName	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.11	DisplayString	read-create	Access concentrator name for paepvc.
STR dtpvcServiceName	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.12	DisplayString	read-create	Service name for paepvc.
INT dtpvcHelloTime	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.13	INTEGER	read-create	The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
dtpvcStateTable	1.3.6.1.4.1.6321.1.2.3.1.8.14.2		not-accessible	This table show current DTPVC status.
dtpvcStateEntry	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1		not-accessible	An entry in dtpvcStateTable.
INT dtpvcStateVpi	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.1	INTEGER	read-only	VPI of the dtpvc.
INT dtpvcStateVci	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.2	INTEGER	read-only	VCI of the dtpvc.
VLA dtpvcStateSvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.3	VlanIndex	read-only	Default S-VID of the dtpvc.
INT dtpvcStateSPriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.4	INTEGER	read-only	S-priority of the dtpvc.
VLA dtpvcStateCvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.5	VlanIndex	read-only	Default C-VID of the dtpvc.
INT dtpvcStateCPriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.6	INTEGER	read-only	C-priority of the dtpvc.
STR dtpvcStateChannelType	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.8	DisplayString	read-only	The value of this object identifies the channel type at runtime.
STR dtpvcStateEncap	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.9	DisplayString	read-only	The value of this object identifies the channel encapsulation at runtime.
snrMgn	1.3.6.1.4.1.6321.1.2.3.1.8.15
snrMgnTable	1.3.6.1.4.1.6321.1.2.3.1.8.15.1		not-accessible	A table containing the per port SNR Margin configuration.
snrMgnEntry	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1		not-accessible	An entry of snrMgnTable.
INT snrMgnMode	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.1	INTEGER	read-write	Configure DSL SNR margin configuration mode of the specified ports. Profile: the SNR margin configuration comes from DSL profile. Line: the SNR margin configuration comes from line configuration.
INT snrMgnUcTarget	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.2	INTEGER	read-write	Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
INT snrMgnUcMax	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.3	INTEGER	read-write	Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
INT snrMgnUcMin	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.4	INTEGER	read-write	Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
INT snrMgnUcDownshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.5	INTEGER	read-write	Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
INT snrMgnUcUpshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.6	INTEGER	read-write	Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
INT snrMgnUrTarget	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.7	INTEGER	read-write	Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
INT snrMgnUrMax	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.8	INTEGER	read-write	Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
INT snrMgnUrMin	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.9	INTEGER	read-write	Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
INT snrMgnUrDownshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.10	INTEGER	read-write	Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
INT snrMgnUrUpshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.11	INTEGER	read-write	Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
dslRate	1.3.6.1.4.1.6321.1.2.3.1.8.16
dslRateTable	1.3.6.1.4.1.6321.1.2.3.1.8.16.1		not-accessible	A table containing the per port DSL Rate configuration.
dslRateEntry	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1		not-accessible	An entry of dslRateTable.
INT dslRateMode	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.1	INTEGER	read-write	Configure DSL Rate configuration mode of the specified ports. Profile: the DSL Rate configuration comes from DSL profile. Line: the DSL Rate configuration comes from line configuration.
INT dslRateLatencyMode	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.2	INTEGER	read-only	The latency mode is fast or interleave
INT dslRateXtucMaxInterleaveDelay	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.3	INTEGER	read-write	Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
U32 dslRateXtucMaxTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.4	Unsigned32	read-write	Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
U32 dslRateXtucMinTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.5	Unsigned32	read-write	Configured Minimum Transmit rate for `Fast' or `Interleave' channels, in bps
INT dslRateXturMaxInterleaveDelay	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.6	INTEGER	read-write	Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency
U32 dslRateXturMaxTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.7	Unsigned32	read-write	Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
U32 dslRateXturMinTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.8	Unsigned32	read-write	Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
gbond	1.3.6.1.4.1.6321.1.2.3.1.8.51
gbondGroupTable	1.3.6.1.4.1.6321.1.2.3.1.8.51.1		not-accessible	A table containing the G.Bond configuration information for each bonding group of the device.
gbondGroupEntry	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1		not-accessible	An entry of gbondTable.
OCT gbondGroupName	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.1	OCTET STRING	read-only	An administratively assigned string, which may be used to identify bonding group.
OCT gbondGroupPorts	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.2	OCTET STRING	read-create	The set of ports which are currently assigned to the bonding group of specified group name. Byte 1: Reserved(chassis) Byte 2~3: Reserved(slot) Byte 4: Reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
U32 gbondGroupUpRate	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.4	Unsigned32	read-only	The UP stream rate.
U32 gbondGroupDownRate	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.5	Unsigned32	read-only	The DOWN stream rate.
ROW gbondGroupRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.6	RowStatus	read-create	This object indicates the status of this entry.
switch	1.3.6.1.4.1.6321.1.2.3.1.10
dscp	1.3.6.1.4.1.6321.1.2.3.1.10.10
dscpMappingTable	1.3.6.1.4.1.6321.1.2.3.1.10.10.1		not-accessible	The table contains DSCP mapping configuration for the adsl and ethernet ports.
dscpMappingEntry	1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1		not-accessible	An entry of dscpMappingTable.
INT dscpSrcCodePoint	1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.1	INTEGER	read-only	The DSCP source code point used for mapping.
INT dscpMapPriority	1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.3	INTEGER	read-write	The mapping p bits that will replace the source p bits in the incoming packet.
dscpPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.10.2		not-accessible	The table contains DSCP mapping configuration for the adsl and ethernet ports.
dscpPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1		not-accessible	An entry of dscpPortTable.
INT dscpStatusEnable	1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1.1	INTEGER	read-write	The DSCP port status.
vlanIsolation	1.3.6.1.4.1.6321.1.2.3.1.10.12
vlanIsolationTable	1.3.6.1.4.1.6321.1.2.3.1.10.12.1		not-accessible	A table contains configuration of isolated VLAN.
vlanIsolationEntry	1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1		not-accessible	An entry of vlanIsolationTable.
ROW vlanIsolationRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1.1	RowStatus	read-create	Row status of the table used to create/delete an entry.
enetMtu	1.3.6.1.4.1.6321.1.2.3.1.10.13
INT enetMtuEntry	1.3.6.1.4.1.6321.1.2.3.1.10.13.1	INTEGER	read-write	Sets the MTU size for layer 2 frame, size from 1526 to 1532, default value is 1526.
dhcp	1.3.6.1.4.1.6321.1.2.3.1.10.51
dhcpRelay82Table	1.3.6.1.4.1.6321.1.2.3.1.10.51.2		not-accessible	A table that contains DHCP Relay configuration.
dhcpRelay82Entry	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1		not-accessible	The entry of DHCP Relay table.
IP dhcpRelay82PrimaryServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.1	IpAddress	read-write	The IP address of the DHCP Relay primary server.
IP dhcpRelay82SecondaryServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.2	IpAddress	read-write	The IP address of the DHCP Relay secondary server.
INT dhcpRelay82ActiveServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.3	INTEGER	read-only	The current active DHCP Relay server.
INT dhcpRelay82Enable	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.4	INTEGER	read-create	Enable/disable DHCP relay and Option82 function.
STR dhcpRelay82Info	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.5	DisplayString	read-create	User specific Option82 information.
INT dhcpRelay82RelayMode	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.6	INTEGER	read-create	DHCP relay mode.
INT dhcpRelay82Suboption2Enable	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.8	INTEGER	read-create	Enable/disable Option 82 sub-option 2.
STR dhcpRelay82Suboption2Info	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.9	DisplayString	read-create	User specified information for Option 82 sub-option 2.
INT dhcpRelay82EntryEnable	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.10	INTEGER	read-create	Enable/disable DHCP Relay
INT dhcpRelay82EntryOptionMode	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.11	INTEGER	read-create	Option82 format.
IP dhcpRelay82VlanIp	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.12	IpAddress	read-write	The IP address of the DHCP Relay interface for this VLAN.
INT dhcpRelay82VlanMask	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.13	INTEGER	read-write	The network mask of the DHCP Relay interface for this VLAN.
IP dhcpRelay82VlanGateway	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.14	IpAddress	read-write	The gateway of the DHCP Relay interface for this VLAN.
IP dhcpRelay82ThirdServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.15	IpAddress	read-write	The IP address of the DHCP Relay third server.
IP dhcpRelay82FourthServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.16	IpAddress	read-write	The IP address of the DHCP Relay fourth server.
IP dhcpRelay82FifthServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.17	IpAddress	read-write	The IP address of the DHCP Relay fifth server.
INT dhcpRelay82ServerVid	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.18	INTEGER	read-write	The VID of the DHCP Relay server for this VLAN.
dhcpRelayTest	1.3.6.1.4.1.6321.1.2.3.1.10.51.8
INT dhcpRelayTestVid	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.1	INTEGER	read-write	Setting the VID of the test server.
IP dhcpRelayTestIp	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.2	IpAddress	read-write	Setting the IP of the test server.
INT dhcpRelayTestOps	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.3	INTEGER	read-write	Set the object to 1 to test DHCP server.
STR dhcpRelayTestStatus	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.4	DisplayString	read-only	Display testing server status.
dhcpRelayArp	1.3.6.1.4.1.6321.1.2.3.1.10.51.9
dhcpRelayArpShowTable	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1		not-accessible	The table displays DHCP ARP.
dhcpRelayArpShowEntry	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1		not-accessible	An entry of dhcpRelayArpShowTable.
INT dhcpRelayArpShowVid	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.1	INTEGER	read-only	Display the VID of the DHCP ARP entry.
IP dhcpRelayArpShowIp	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.2	IpAddress	read-only	Display the IP of the DHCP ARP entry.
PHY dhcpRelayArpShowMac	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.3	PhysAddress	read-only	Display the MAC of the DHCP ARP entry.
INT dhcpRelayArpFlushOps	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.2	INTEGER	read-write	Set the object to 1 to start flushing.
macfilter	1.3.6.1.4.1.6321.1.2.3.1.10.53
macFilterPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.1		not-accessible	This table includes the status of mac filtering for each port.
macFilterPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1		not-accessible	An entry in macFilterPortTable.
INT macFilterPortEnable	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.1	INTEGER	read-write	Enable/disable MAC filtering for the port.
INT macFilterPortMacCount	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.2	INTEGER	read-write	The total number of MAC addresses allowed for the port.
INT macFilterPortFilterMode	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.3	INTEGER	read-write	The mac filter mode (accept or deny) for the port.
INT maxNumOfMacFiltersInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.53.2	INTEGER	read-only	The max number of mac filters supported in the system.
INT maxNumOfMacFiltersPerPort	1.3.6.1.4.1.6321.1.2.3.1.10.53.3	INTEGER	read-only	The max number of mac filters supported per port.
INT currNumOfMacFiltersInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.53.4	INTEGER	read-only	The current number of mac filters in the system.
macFilterTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.5		not-accessible	A table that contains the mac filter addresses.
macFilterEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1		not-accessible	The entry of macFilterTable.
PHY macFilterAddr	1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.1	PhysAddress	read-only	The mac address which can pass through or be rejected from the port.
ROW macFilterRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.2	RowStatus	read-create	The row status of the entry.
macfilterBatchSet	1.3.6.1.4.1.6321.1.2.3.1.10.53.6
OCT macfilterTarget	1.3.6.1.4.1.6321.1.2.3.1.10.53.6.1	OCTET STRING	read-write	This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chassis) Byte 2~3: 0, Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
INT macfilterOps	1.3.6.1.4.1.6321.1.2.3.1.10.53.6.2	INTEGER	read-write	The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable mac filter BIT 2: enable mac count filter BIT 3: disable mac filter BIT 4: set mac count BIT 5: disable mac count filter.
INT macFilterMacCountForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.10.53.6.3	INTEGER	read-write	The total number of MAC addresses allowed for a port.
ouiFilterTableOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7		not-accessible	A table that contains the OUI filter addresses.
ouiFilterEntryOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1		not-accessible	The entry of ouiFilterTableOld.
OCT ouiFilterAddrOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.1	OCTET STRING	read-only	The first three bytes of the mac address which can pass through or be rejected from the port.
ROW ouiFilterRowStatusOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.2	RowStatus	read-create	The row status of the entry.
INT maxNumOfOuiFiltersPerPort	1.3.6.1.4.1.6321.1.2.3.1.10.53.8	INTEGER	read-only	The max number of OUI filters supported per port.
ouiFilterPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.9		not-accessible	This table includes the status of oui filtering for each port.
ouiFilterPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1		not-accessible	An entry in macFilterPortTable.
INT ouiFilterPortEnable	1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.1	INTEGER	read-write	Enable/disable oui filtering for the port.
INT ouiFilterPortFilterMode	1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.2	INTEGER	read-write	The oui filter mode (accept or deny) for the port.
INT maxNumOfOuiFiltersInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.53.10	INTEGER	read-only	The max number of OUI filters supported in system.
INT maxNumOfOuiFiltersPerVlan	1.3.6.1.4.1.6321.1.2.3.1.10.53.11	INTEGER	read-only	The max number of OUI filters supported per vlan.
ouiFilterTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.12		not-accessible	A table that contains the OUI filter addresses.
ouiFilterEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1		not-accessible	The entry of ouiFilterTable.
OCT ouiFilterAddr	1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.1	OCTET STRING	read-only	The first three bytes of the mac address which can pass through or be rejected from the vlan.
ROW ouiFilterRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.2	RowStatus	read-create	The row status of the entry.
ouiFilterVlanTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.13		not-accessible	This table includes the status of oui filtering for each configured VLAN.
ouiFilterVlanEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1		not-accessible	An entry in ouiFilterVlanTable.
INT ouiFilterVlanEnable	1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.1	INTEGER	read-write	Enable/disable oui filtering for the VLAN.
INT ouiFilterVlanFilterMode	1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.2	INTEGER	read-write	The oui filter mode (accept or deny) for the VLAN.
dhcpSnoop	1.3.6.1.4.1.6321.1.2.3.1.10.55
dhcpSnoopPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.55.1		not-accessible	This table includes DHCP snooping enable/disable for each port.
dhcpSnoopPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1		not-accessible	An entry of dhcpSnoopPortTable.
INT dhcpSnoopEnable	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.1	INTEGER	read-write	Enable/disable DHCP snooping for a port.
INT dhcpSnoopMaxcnt	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.2	INTEGER	read-write	Set the max entries of the DHCP ARP table.
INT dhcpSnoopSmacverifyEnable	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.3	INTEGER	read-write	Enable/disable DHCP source MAC verify for a port.
OCT dhcpSnoopTarget	1.3.6.1.4.1.6321.1.2.3.1.10.55.2	OCTET STRING	read-write	This managed object is used for identify the target on which the operation should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
INT dhcpSnoopOps	1.3.6.1.4.1.6321.1.2.3.1.10.55.3	INTEGER	read-write	The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: DHCP snooping table flush.
dhcpStaticTable	1.3.6.1.4.1.6321.1.2.3.1.10.55.4		not-accessible	This table defines DHCP static IP addresses.
dhcpStaticEntry	1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1		not-accessible	An entry of dhcpStaticTable.
IP dhcpStaticIpAddr	1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.1	IpAddress	read-only	The IP address which can pass through the port.
ROW dhcpStaticRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.2	RowStatus	read-create	Row status of the table entry.
INT maxNumOfDhcpStaticIp	1.3.6.1.4.1.6321.1.2.3.1.10.55.5	INTEGER	read-only	The maximum number of DHCP static IP addresses which can be created for a port.
INT dhcpSnoopMaxcntMode	1.3.6.1.4.1.6321.1.2.3.1.10.55.6	INTEGER	read-write	When DHCP snooping table is full, new DHCP lease will replace first one in option 0 or will be dropped in option 1.
acl	1.3.6.1.4.1.6321.1.2.3.1.10.56
aclSetTable	1.3.6.1.4.1.6321.1.2.3.1.10.56.1		not-accessible	aclsetTable.
aclSetEntry	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1		not-accessible	An entry of aclSetTable.
INT aclSetVpi	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.1	INTEGER	read-only	VPI value
INT aclSetVci	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.2	INTEGER	read-only	VCI value
STR aclSetProfileName	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.3	DisplayString	read-only	ACL Profile name
ROW aclSetRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.4	RowStatus	read-write	RowStatus of aclSetEntry
aclProfileTable	1.3.6.1.4.1.6321.1.2.3.1.10.56.2		not-accessible	aclProfileTable.
aclProfileEntry	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1		not-accessible	An entry of aclProfileTable.
STR aclProfileRuleName	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.1	DisplayString	read-only	Profile rule name
INT aclProfileRuleNumber	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.2	INTEGER	read-write	The managed object is for acl profile rule configuration. etype vlan (1), etype smac (2), etype dmac (3), vlan smac (4), vlan dmac (5), smac dmac (6), vlan priority (7), etype (8), vlan (9), smac (10), dmac (11), priority (12), protocol (13), {srcip /{\|dstip /{\|tos {\|srcport {\|dstport }}}}} (14)
INT aclProfileActionNumber	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.3	INTEGER	read-write	Profile action number. Bit 1: rate Bit 2: rvlan Bit 3: rpri Bit 4: deny Bit 1, Bit 2 & Bit 3 can multiple selection.
INT aclProfileRuleParamMask	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.4	INTEGER	read-write	Profile rule parameter mask. BIT 1: srcip / BIT 2: dstip / BIT 3: tos BIT 4: srcport BIT 5: dstport
INT aclProfileRuleEtype	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.5	INTEGER	read-write	Profile rule etype
INT aclProfileRuleVid	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.6	INTEGER	read-write	Profile rule vid
PHY aclProfileRuleSmac	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.7	PhysAddress	read-write	Profile rule source MAC
PHY aclProfileRuleDmac	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.8	PhysAddress	read-write	Profile rule destination MAC
INT aclProfileRulePriority	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.9	INTEGER	read-write	Profile rule priority
INT aclProfileRuleProtocol	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.10	INTEGER	read-write	Profile rule protocol. icmp(1),igmp(2),ip(4),tcp(6), udp(17),gre(47),ospf(89), other ptype
IP aclProfileRuleSrcIP	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.11	IpAddress	read-write	Profile rule source IP
INT aclProfileRuleSrcIPMask	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.12	INTEGER	read-write	The subnet mask of source IP mask
IP aclProfileRuleDestIP	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.13	IpAddress	read-write	Profile rule source IP
INT aclProfileRuleDestIPMask	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.14	INTEGER	read-write	The subnet mask of dest IP mask
INT aclProfileRuleStartTos	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.15	INTEGER	read-write	Profile rule start type of service
INT aclProfileRuleEndTos	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.16	INTEGER	read-write	Profile rule end type of service
INT aclProfileRuleSrcStartPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.17	INTEGER	read-write	Profile rule source start port
INT aclProfileRuleSrcEndPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.18	INTEGER	read-write	Profile rule source end port
INT aclProfileRuleDestStartPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.19	INTEGER	read-write	Profile rule destination start port
INT aclProfileRuleDestEndPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.20	INTEGER	read-write	Profile rule destination end port
INT aclProfileActionRate	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.21	INTEGER	read-write	Profile action to replace to this rate
INT aclProfileActionrvlan	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.22	INTEGER	read-write	Profile action to replace to this vlan
INT aclProfileActionrpri	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.23	INTEGER	read-write	Profile action to replace to this priority
ROW aclProfileRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.24	RowStatus	read-write	The row status of the entry.
pppoeAgent	1.3.6.1.4.1.6321.1.2.3.1.10.57
pppoeAgentTable	1.3.6.1.4.1.6321.1.2.3.1.10.57.1		not-accessible	A table that contains PPPoE DHCP Relay configuration.
pppoeAgentEntry	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1		not-accessible	An entry of pppoeAgentTable.
INT pppoeAgentEnable	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.1	INTEGER	read-create	Enable/disable DHCP relay and Option82 function.
STR pppoeAgentInfo	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.2	DisplayString	read-create	User specific Option82 information.
ROW pppoeAgentRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.3	RowStatus	read-create	Row status of the table entry.
INT pppoeAgentOptionMode	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.4	INTEGER	read-create	Option82 format.
INT maxNumOfPppoeDhcpRelay82Conf	1.3.6.1.4.1.6321.1.2.3.1.10.57.2	INTEGER	read-only	The maximum number of rows that can be created in pppoeAgentTable.
macff	1.3.6.1.4.1.6321.1.2.3.1.10.60
macFfTable	1.3.6.1.4.1.6321.1.2.3.1.10.60.1		not-accessible	A table that contains MAC Force Forwarding configuration.
macFfEntry	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1		not-accessible	An entry of macFfTable.
INT macFfIndex	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.1	INTEGER	read-only	Index of the MACFF.
INT macFfVid	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.2	INTEGER	read-write	The VLAN-ID refering to this AR/AS.
IP macFfArIP	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.3	IpAddress	read-write	IP of this AR/AS
IP macFfSrcIP	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.4	IpAddress	read-write	The source IP address of the MACFF.
INT macFfSrcMask	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.5	INTEGER	read-write	The subnet mask of source IP mask.
ROW macFfRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.6	RowStatus	read-create	The row status of the MacFfEntry entry.
INT macFfArpFlush	1.3.6.1.4.1.6321.1.2.3.1.10.60.3	INTEGER	read-write	Set the object to 1 to flush mac table.
INT maxNumOfMacFfVlanInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.60.4	INTEGER	read-only	The max number of macff Vlans supported in the system.
macFfVlanTable	1.3.6.1.4.1.6321.1.2.3.1.10.60.5		not-accessible	A table that contains MAC Force Forwarding Vlan configuration.
macFfVlanEntry	1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1		not-accessible	An entry of macFfVlanTable.
ROW macFfVlanRowstatus	1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.1	RowStatus	read-create	Row status of the table used to create/delete an entry.
INT macFfVlanUnknownUnicast	1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.2	INTEGER	read-create	Setting downstream unknown uni-cast packet on macff vlan to flooding or dropping.
macFfStaticIPTable	1.3.6.1.4.1.6321.1.2.3.1.10.60.6		not-accessible
macFfStaticIPEntry	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1		not-accessible	An entry of macFfTable.
INT macFfStaticIPPort	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.1	INTEGER	read-only	The port number, 1 ~ 48.
INT macFfStaticIPVid	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.2	INTEGER	read-only	VLAN ID of the IP range, 1 ~ 4094, the vid should be enable the MACFF function first.
IP macFfstaticIP	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.3	IpAddress	read-only	The specified IP range.
INT macFfStaticIPMask	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.4	INTEGER	read-only	Mask_bits is 24 .. 32.
ROW macFfStaticIPRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.5	RowStatus	read-create	The row status used to configure the table entry.
sys	1.3.6.1.4.1.6321.1.2.3.1.11
accessCtrl	1.3.6.1.4.1.6321.1.2.3.1.11.5
securedClientTable	1.3.6.1.4.1.6321.1.2.3.1.11.5.2		not-accessible	A table that contains information about secured clients.
securedClientEntry	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1		not-accessible	A list of secured client entry.
INT securedClientIndex	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.1	INTEGER	read-only	The index of the entry.
IP securedClientStartIp	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.2	IpAddress	read-write	The starting IP address of the secured client set.
IP securedClientEndIp	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.3	IpAddress	read-write	The ending IP address of the secured client set.
INT securedClientService	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.4	INTEGER	read-write	Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1: telnet BIT 2: ftp BIT 3: web BIT 4: icmp BIT 5: not support BIT 6: snmp.
INT securedClientEnable	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.5	INTEGER	read-write	Enable/disable the entry.
extAlarm	1.3.6.1.4.1.6321.1.2.3.1.11.8
extAlarmTable	1.3.6.1.4.1.6321.1.2.3.1.11.8.1		not-accessible	A table that contains external alarm information.
extAlarmEntry	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1		not-accessible	The entry of external alarm table.
INT extAlarmIndex	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.1	INTEGER	read-only	The index of the entry.
STR extAlarmname	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.2	DisplayString	read-write	The external alarm name.
STR extAlarmstatus	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.3	DisplayString	read-only	Dispaly 'Normal' or 'Alarm' string
INT extAlarmTriggeredMode	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.4	INTEGER	read-write	The external alarm triggered mode.
user	1.3.6.1.4.1.6321.1.2.3.1.11.9
INT userAuthMode	1.3.6.1.4.1.6321.1.2.3.1.11.9.1	INTEGER	read-write	User authentication procsssing mode.
IP userAuthServerIp	1.3.6.1.4.1.6321.1.2.3.1.11.9.2	IpAddress	read-write	The IP address of the authentication server.
INT userAuthServerPort	1.3.6.1.4.1.6321.1.2.3.1.11.9.3	INTEGER	read-write	The port of the authentication server.
OCT userAuthServerSecret	1.3.6.1.4.1.6321.1.2.3.1.11.9.4	OCTET STRING	read-write	The secret between the authentication server and the NE for authentication process.
userTable	1.3.6.1.4.1.6321.1.2.3.1.11.9.5		not-accessible	A table that contains user information.
userEntry	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1		not-accessible	An entry of userTable.
STR userName	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.1	DisplayString	read-only	The user name.
STR userPassword	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.2	DisplayString	read-create	The user password.
INT userPriviledge	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.3	INTEGER	read-create	The user priviledge to decide what operation the user can and cannot do.
ROW userRowStatus	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.4	RowStatus	read-create	The row status used to create or delete a user.
INT userAuthDefaultPriviledge	1.3.6.1.4.1.6321.1.2.3.1.11.9.6	INTEGER	read-write	The user default priviledge to be assigned when radius authentication succeds but no user priviledge information(radius service-type) is provided.
usbCastCtrl	1.3.6.1.4.1.6321.1.2.3.1.11.10
INT usBcastCtrlEnable	1.3.6.1.4.1.6321.1.2.3.1.11.10.1	INTEGER	read-write	Enable/disable upstream broadcast control.
INT usBcastCtrlRate	1.3.6.1.4.1.6321.1.2.3.1.11.10.2	INTEGER	read-write	32~49984 in step of 32kbps
dsbCastCtrl	1.3.6.1.4.1.6321.1.2.3.1.11.11
INT dsBcastCtrlEnable	1.3.6.1.4.1.6321.1.2.3.1.11.11.1	INTEGER	read-write	Enable/disable downstream broadcast control.
INT dsBcastCtrlRate	1.3.6.1.4.1.6321.1.2.3.1.11.11.2	INTEGER	read-write	32~1000000 in step of 32 kbps
INT stdioTimeout	1.3.6.1.4.1.6321.1.2.3.1.11.12	INTEGER	read-write	Set the CLI/TELNET/WEB Session timeout, 0, or 1~300 minutes, 0 => disable.
INT isConfigChanged	1.3.6.1.4.1.6321.1.2.3.1.11.13	INTEGER	read-only	If system configuration has been changed.
fwUpgrade	1.3.6.1.4.1.6321.1.2.3.1.11.14
OCT fwUpgradeVersion	1.3.6.1.4.1.6321.1.2.3.1.11.14.1	OCTET STRING	read-write	Configure the target firmware version that will be upgraded.
INT fwUpgradeCheck	1.3.6.1.4.1.6321.1.2.3.1.11.14.2	INTEGER	read-write	Enable/disable firmware upgrade version checking feature.
STR fwUpgradeStatus	1.3.6.1.4.1.6321.1.2.3.1.11.14.3	DisplayString	read-only	Display current firmware upgrade status.
delayedReboot	1.3.6.1.4.1.6321.1.2.3.1.11.15
INT delayedRebootTimer	1.3.6.1.4.1.6321.1.2.3.1.11.15.1	INTEGER	read-write	5~1800 secs, 0: reboot immediately.
INT delayedRebootRemainingTime	1.3.6.1.4.1.6321.1.2.3.1.11.15.2	INTEGER	read-only	Display the remaining time of scheduled reboot.
INT delayedRebootCancel	1.3.6.1.4.1.6321.1.2.3.1.11.15.3	INTEGER	read-write	cancel the scheduled reboot.
trap	1.3.6.1.4.1.6321.1.2.3.1.12
statistics	1.3.6.1.4.1.6321.1.2.3.1.13
C32 igmpQueryCntTotal	1.3.6.1.4.1.6321.1.2.3.1.13.1	Counter32	read-only	The total number of IGMP query messages received.
C32 igmpReportCntTotal	1.3.6.1.4.1.6321.1.2.3.1.13.2	Counter32	read-only	The total number of IGMP report messages received.
C32 igmpLeaveCntTotal	1.3.6.1.4.1.6321.1.2.3.1.13.3	Counter32	read-only	The total number of IGMP leave messages received.
INT igmpNumOfActiveGroups	1.3.6.1.4.1.6321.1.2.3.1.13.4	INTEGER	read-only	The total number of IGMP learned groups.
igmpGroupTable	1.3.6.1.4.1.6321.1.2.3.1.13.5		not-accessible	This table includes igmp group information.
igmpGroupEntry	1.3.6.1.4.1.6321.1.2.3.1.13.5.1		not-accessible	An entry in igmpGroupTable.
IP igmpGroupIp	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.1	IpAddress	read-only	igmp group IP
INT igmpGroupvid	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.2	INTEGER	read-only	vlan id
INT igmpGroupnumberOfMembers	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.3	INTEGER	read-only	number Of Members
POR igmpGroupMemberPorts	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.4	PortList	read-only	Group Member Ports
igmpGroupPortTable	1.3.6.1.4.1.6321.1.2.3.1.13.6		not-accessible	This table includes igmp Group port information.
igmpGroupPortEntry	1.3.6.1.4.1.6321.1.2.3.1.13.6.1		not-accessible	An entry in igmpGroupPortTable.
IP igmpGroupPortIp	1.3.6.1.4.1.6321.1.2.3.1.13.6.1.1	IpAddress	read-only	Igmp Group IP
INT igmpGroupPortvid	1.3.6.1.4.1.6321.1.2.3.1.13.6.1.2	INTEGER	read-only	Igmp Group vid
igmpGroupV2Table	1.3.6.1.4.1.6321.1.2.3.1.13.7		not-accessible	A table that displays IGMP learned group member information.
igmpGroupV2Entry	1.3.6.1.4.1.6321.1.2.3.1.13.7.1		not-accessible	An entry of igmpGroupV2Table.
VLA igmpGroupV2Vid	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.1	VlanIndex	read-only	The IGMP group VLAN ID.
IP igmpGroupV2Ip	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.2	IpAddress	read-only	The multicast IP address.
INT igmpGroupV2NumOfMembers	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.3	INTEGER	read-only	The number of member ports in the group.
POR igmpGroupV2MemberPorts	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.4	PortList	read-only	The member port list of the group.
igmpGroupPortV2Table	1.3.6.1.4.1.6321.1.2.3.1.13.8		not-accessible	A table that displays IGMP joined groups in this port.
igmpGroupPortV2Entry	1.3.6.1.4.1.6321.1.2.3.1.13.8.1		not-accessible	An entry of igmpGroupPortV2Table.
VLA igmpGroupPortV2Vid	1.3.6.1.4.1.6321.1.2.3.1.13.8.1.1	VlanIndex	read-only	The IGMP group VLAN ID.
IP igmpGroupPortV2Ip	1.3.6.1.4.1.6321.1.2.3.1.13.8.1.2	IpAddress	read-only	The multicast IP address.
IP igmpGroupPortV2SourceIp	1.3.6.1.4.1.6321.1.2.3.1.13.8.1.3	IpAddress	read-only	The source IP address that joins the IGMP group.
igmpPortCtrlPduTable	1.3.6.1.4.1.6321.1.2.3.1.13.9		not-accessible	A table that displays IGMP related counter values in this port.
igmpPortCtrlPduEntry	1.3.6.1.4.1.6321.1.2.3.1.13.9.1		not-accessible	An entry of igmpPortCtrlPduTable.
C32 igmpPortCtrlPduQueryCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.1	Counter32	read-only	The total number of IGMP query messages received in this port.
C32 igmpPortCtrlPduReportCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.2	Counter32	read-only	The total number of IGMP report messages received in this port.
C32 igmpPortCtrlPduLeaveCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.3	Counter32	read-only	The total number of IGMP leave messages received in this port.
INT igmpPortNumOfActiveGroups	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.4	INTEGER	read-only	The total number of active IGMP groups in this port.
C32 igmpPortCtrlAuditLeaveCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.5	Counter32	read-only	The total number of groups left by audit query.
dhcpStats	1.3.6.1.4.1.6321.1.2.3.1.13.11
dhcpSnoopIpTable	1.3.6.1.4.1.6321.1.2.3.1.13.11.1		not-accessible	This table shows the IP addresses and netmasks offered by the DHCP server.
dhcpSnoopIpEntry	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1		not-accessible	An entry of dhcpSnoopIpTable.
IP dhcpSnoopIp	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.1	IpAddress	read-only	The snooped IP address.
PHY dhcpSnoopMac	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.2	PhysAddress	read-only	The snooped MAC address.
VLA dhcpSnoopVid	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.3	VlanIndex	read-only	The snooped VLAN ID.
INT dhcpSnoopMask	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.4	INTEGER	read-only	The snooped IP mask
IP dhcpSnoopGateway	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.5	IpAddress	read-only	The snooped Gateway.
OCT dhcpSnoopRouteMap	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.6	OCTET STRING	read-only	The refrence bit map of the dhcp route
dhcpSnoopCounterTable	1.3.6.1.4.1.6321.1.2.3.1.13.11.2		not-accessible	This table shows the DHCP statistics.
dhcpSnoopCounterEntry	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1		not-accessible	An entry of dhcpSnoopCounterTable.
C64 dhcpDiscovery	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.1	Counter64	read-only	The total number of received DHCP server discovery packets.
C64 dhcpOffer	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.2	Counter64	read-only	The total number of received DHCP server offer packets.
C64 dhcpRequest	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.3	Counter64	read-only	The total number of received DHCP IP request packets.
C64 dhcpAck	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.4	Counter64	read-only	The total number of received DHCP IP acknowledge packets.
C64 dhcpAckBySnoopFull	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.5	Counter64	read-only	The total number of received DHCP IP acknowledge packets that replace the oldest snooping entry in snooping table due to table full.
dhcpRouteTable	1.3.6.1.4.1.6321.1.2.3.1.13.11.3		not-accessible	A table that contains dhcp route information.
dhcpRouteEntry	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1		not-accessible	An entry of dhcpRouteTable.
INT dhcpRouteIndex	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.1	INTEGER	read-only
VLA dhcpRouteVid	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.2	VlanIndex	read-only	The VLAN-ID refering to this dhcp route.
IP dhcpRouteIP	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.3	IpAddress	read-only	IP of this dhcp route
INT dhcpRouteMask	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.4	INTEGER	read-only	The subnet mask of source IP mask.
IP dhcpRouteGwIP	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.5	IpAddress	read-only	The gateway IP address.
paepvcStats	1.3.6.1.4.1.6321.1.2.3.1.13.12
paepvcSessionTable	1.3.6.1.4.1.6321.1.2.3.1.13.12.1		not-accessible	This table shows the paepvc session statistics.
paepvcSessionEntry	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1		not-accessible	An entry of paepvcSessionTable.
INT paepvcSessionVpi	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.1	INTEGER	read-only	The PAEPVC VPI.
INT paepvcSessionVci	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.2	INTEGER	read-only	The PAEPVC VCI.
INT paepvcSessionState	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.3	INTEGER	read-only	The PAEPVC status.
INT paepvcSessionId	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.4	INTEGER	read-only	The PAEPVC session ID.
U32 paepvcSessionUptime	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.5	Unsigned32	read-only	The PAEPVC session uptime.
STR paepvcSessionacname	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.6	DisplayString	read-only	Access concentrator name.
STR paepvcSessionsrvcname	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.7	DisplayString	read-only	Service name.
paepvcCountTable	1.3.6.1.4.1.6321.1.2.3.1.13.12.2		not-accessible	This table shows the paepvc counters.
paepvcCountEntry	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1		not-accessible	An entry of paepvcCountTable.
INT paepvcCountVpi	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.1	INTEGER	read-only	The PAEPVC VPI.
INT paepvcCountVci	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.2	INTEGER	read-only	The PAEPVC VCI.
U32 paepvcCountPppLcpCfgReqRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.3	Unsigned32	read-only	The number of ppp lcp config-request received.
U32 paepvcCountPppLcpEchoReqRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.4	Unsigned32	read-only	The number of ppp lcp echo-request received.
U32 paepvcCountPppLcpEchoReplyRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.5	Unsigned32	read-only	The number of ppp lcp echo-reply received.
U32 paepvcCountPadiTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.6	Unsigned32	read-only	The number of pppoe padi transfered
U32 paepvcCountPadoRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.7	Unsigned32	read-only	The number of pppoe pado received
U32 paepvcCountPadrTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.8	Unsigned32	read-only	The number of pppoe padr transfered
U32 paepvcCountPadsRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.9	Unsigned32	read-only	The number of pppoe pads received
U32 paepvcCountPadtTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.10	Unsigned32	read-only	The number of pppoe padt transfered
U32 paepvcCountPadtRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.11	Unsigned32	read-only	The number of pppoe padt received
U32 paepvcCountSrvcnameErrRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.12	Unsigned32	read-only	The number of pppoe service name error received
U32 paepvcCountAcSystemErrRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.13	Unsigned32	read-only	The number of pppoe access concentrator name error received
U32 paepvcCountGenericErrTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.14	Unsigned32	read-only	The number of pppoe generic error transfered
U32 paepvcCountGenericErrRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.15	Unsigned32	read-only	The number of pppoe generic error received
macStats	1.3.6.1.4.1.6321.1.2.3.1.13.13
INT macDisplayTarget	1.3.6.1.4.1.6321.1.2.3.1.13.13.1	INTEGER	read-write	This managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. The target could be: 99: all ports in the system 98: all subscriber ports 97: all Ethernet ports IfIndex is used for identifying subscriber ports and Ethernet Ports(e.g. 1 ~ 50).
macTable	1.3.6.1.4.1.6321.1.2.3.1.13.13.2		not-accessible	A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
macEntry	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1		not-accessible	An entry of macTable.
MAC macAddress	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.1	MacAddress	read-only	A unicast MAC address for which the bridge has forwarding and/or filtering information.
INT macPort	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.2	INTEGER	read-only	The port from which the mac address has been learned.
INT macStatus	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.3	INTEGER	read-only	The status of this entry.
ipbpvcStats	1.3.6.1.4.1.6321.1.2.3.1.13.14
arpproxyTable	1.3.6.1.4.1.6321.1.2.3.1.13.14.1		not-accessible	Display ARP table. This table is supported by R3.00 and later versions.
arpproxyEntry	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1		not-accessible	An entry of arpproxyTable.
IP arpproxyIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.1	IpAddress	read-only
MAC arpproxyMac	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.2	MacAddress	read-only
INT arpproxyIfIndex	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.3	INTEGER	read-only
INT arpproxyVpi	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.4	INTEGER	read-only
INT arpproxyVci	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.5	INTEGER	read-only
IP arpproxyInterfaceIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.6	IpAddress	read-only
INT arpproxyInterfaceMask	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.7	INTEGER	read-only
VLA arpproxyInterfaceVid	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.8	VlanIndex	read-only
INT arpproxyDhcpIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.9	INTEGER	read-only
INT arpproxyType	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.10	INTEGER	read-only
ipbpvcIfDynamicTable	1.3.6.1.4.1.6321.1.2.3.1.13.14.2		not-accessible	Display runtime interfaces. This table is supported by R3.00 and later versions.
ipbpvcIfDynamicEntry	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1		not-accessible	An entry of ipbpvcIfDynamicTable.
IP ipbpvcIfDynamicIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.1	IpAddress	read-only
INT ipbpvcIfDynamicMask	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.2	INTEGER	read-only
INT ipbpvcIfDynamicIfIndex	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.3	INTEGER	read-only
INT ipbpvcIfDynamicVpi	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.4	INTEGER	read-only
INT ipbpvcIfDynamicVci	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.5	INTEGER	read-only
ipbpvcRouteDynamicTable	1.3.6.1.4.1.6321.1.2.3.1.13.14.3		not-accessible	Display runtime routing table. This table is supported by R3.00 and later versions.
ipbpvcRouteDynamicEntry	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1		not-accessible	An entry of ipbpvcRouteDynamicTable.
INT ipbpvcRouteDynamicType	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.1	INTEGER	read-only
IP ipbpvcRouteDynamicIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.2	IpAddress	read-only
INT ipbpvcRouteDynamicMask	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.3	INTEGER	read-only
IP ipbpvcRouteDynamicNextHop	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.4	IpAddress	read-only
INT ipbpvcRouteDynamicMetric	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.5	INTEGER	read-only
INT ipbpvcRouteDynamicPriority	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.6	INTEGER	read-only
macffStats	1.3.6.1.4.1.6321.1.2.3.1.13.16
macFfStatsTable	1.3.6.1.4.1.6321.1.2.3.1.13.16.1		not-accessible	A table that contains MAC Force Forwarding static configuration and dynamic information.
macFfStatsEntry	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1		not-accessible	An entry of macFfStatsTable.
INT macFfStatsIndex	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.1	INTEGER	read-only	Index of the MACFF.
VLA macFfStatsVid	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.2	VlanIndex	read-only	The VLAN-ID refering to this AR/AS.
IP macFfStatsArIP	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.3	IpAddress	read-only	IP of this AR/AS
IP macFfStatsSrcIP	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.4	IpAddress	read-only	The source IP address of the MACFF.
INT macFfStatsSrcMask	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.5	INTEGER	read-only	The subnet mask of source IP mask.
macFfArpTable	1.3.6.1.4.1.6321.1.2.3.1.13.16.2		not-accessible	A table that contains MAC Force Forwarding ARP information.
macFfArpEntry	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1		not-accessible	An entry of macFfArpTable.
VLA macFfArpVid	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.1	VlanIndex	read-only	The VLAN-ID refering to this AR/AS.
IP macFfArpIP	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.2	IpAddress	read-only	IP of this AR/AS.
INT macFfArpPort	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.3	INTEGER	read-only	Port of this AR/AS.
PHY macFfArpMac	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.4	PhysAddress	read-only	MAC address of the AR or AS.
macFfArpCounterTable	1.3.6.1.4.1.6321.1.2.3.1.13.16.3		not-accessible	A table that contains MAC Force Forwarding ARP counter information.
macFfArpCounterEntry	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1		not-accessible	An entry of macFfArpCounterTable.
C32 macFfArpCounterRequestTX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.1	Counter32	read-only	ARP Request TX counter.
C32 macFfArpCounterRequestRX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.2	Counter32	read-only	ARP Request RX counter.
C32 macFfArpCounterRequestRXDrop	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.3	Counter32	read-only	ARP Request RX drop counter.
C32 macFfArpCounterReplyTX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.4	Counter32	read-only	ARP Reply TX counter.
C32 macFfArpCounterReplyRX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.5	Counter32	read-only	ARP Reply RX counter.
C32 macFfArpCounterReplyRXDrop	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.6	Counter32	read-only	ARP Reply RX drop counter.
enetStats	1.3.6.1.4.1.6321.1.2.3.1.13.17
enetSfpInfoTable	1.3.6.1.4.1.6321.1.2.3.1.13.17.2		not-accessible	This table includes sfp info of enet port.
enetSfpInfoEntry	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1		not-accessible	An entry in enetSfpInfoTable.
INT enetSfpInfoTxpower	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.1	INTEGER	read-only	Measured Tx Output Power.
INT enetSfpInfoRxpower	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.2	INTEGER	read-only	Measured Rx Output Power.
INT enetSfpInfoTemperature	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.3	INTEGER	read-only	Measured temperature.
INT enetSfpInfoTxBias	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.4	INTEGER	read-only	Measured tx bias.
INT enetSfpInfoVoltage	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.5	INTEGER	read-only	Measured voltage.
adslStats	1.3.6.1.4.1.6321.1.2.3.1.13.18
adslPortUtilTable	1.3.6.1.4.1.6321.1.2.3.1.13.18.1		not-accessible	This table includes adsl port utilization.
adslPortUtilEntry	1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1		not-accessible	An entry in adslPortUtilEntry.
INT adslPortUtilTx	1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.1	INTEGER	read-only	Measure adsl port's tx utilization.
INT adslPortUtilRx	1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.2	INTEGER	read-only	Measure adsl port's rx utilization.
clear	1.3.6.1.4.1.6321.1.2.3.1.14
OCT counterClearTarget	1.3.6.1.4.1.6321.1.2.3.1.14.1	OCTET STRING	read-write	This managed object is used for identify the target on which the counter would be cleared. The target is encoded as: Byte 1: reserved Byte 2~3: reserved Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
INT counterClearOps	1.3.6.1.4.1.6321.1.2.3.1.14.2	INTEGER	read-write	The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: clear interface counters BIT 2: clear pvc packet counters BIT 3: clear port ATM counters BIT 4: clear pvc ATM counters BIT 5: clear DHCP counters BIT 6: clear IGMP counters BIT 7: clear IGMP port counters BIT 8: clear MACFF ARP counters BIT 9: clear current lineperf BIT 10: clear current 15 minute lineperf BIT 11: clear current 1 day lineperf
INT counterClearVpi	1.3.6.1.4.1.6321.1.2.3.1.14.3	INTEGER	read-write	VPI of the pvc whose counters would be cleared.
INT counterClearVci	1.3.6.1.4.1.6321.1.2.3.1.14.4	INTEGER	read-write	VCI of the pvc whose counters would be cleared.
aesSeriesCommon	1.3.6.1.4.1.6321.1.2.3.1.97
iesSeriesCommon	1.3.6.1.4.1.6321.1.2.3.1.98
accessSwitchCommonATM	1.3.6.1.4.1.6321.1.2.3.1.99

Counter32 (13)
C32 igmpLeaveCntTotal	1.3.6.1.4.1.6321.1.2.3.1.13.3	Counter32	read-only	The total number of IGMP leave messages received.
C32 igmpPortCtrlAuditLeaveCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.5	Counter32	read-only	The total number of groups left by audit query.
C32 igmpPortCtrlPduLeaveCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.3	Counter32	read-only	The total number of IGMP leave messages received in this port.
C32 igmpPortCtrlPduQueryCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.1	Counter32	read-only	The total number of IGMP query messages received in this port.
C32 igmpPortCtrlPduReportCnt	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.2	Counter32	read-only	The total number of IGMP report messages received in this port.
C32 igmpQueryCntTotal	1.3.6.1.4.1.6321.1.2.3.1.13.1	Counter32	read-only	The total number of IGMP query messages received.
C32 igmpReportCntTotal	1.3.6.1.4.1.6321.1.2.3.1.13.2	Counter32	read-only	The total number of IGMP report messages received.
C32 macFfArpCounterReplyRX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.5	Counter32	read-only	ARP Reply RX counter.
C32 macFfArpCounterReplyRXDrop	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.6	Counter32	read-only	ARP Reply RX drop counter.
C32 macFfArpCounterReplyTX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.4	Counter32	read-only	ARP Reply TX counter.
C32 macFfArpCounterRequestRX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.2	Counter32	read-only	ARP Request RX counter.
C32 macFfArpCounterRequestRXDrop	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.3	Counter32	read-only	ARP Request RX drop counter.
C32 macFfArpCounterRequestTX	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.1	Counter32	read-only	ARP Request TX counter.
Counter64 (5)
C64 dhcpAck	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.4	Counter64	read-only	The total number of received DHCP IP acknowledge packets.
C64 dhcpAckBySnoopFull	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.5	Counter64	read-only	The total number of received DHCP IP acknowledge packets that replace the oldest snooping entry in snooping table due to table full.
C64 dhcpDiscovery	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.1	Counter64	read-only	The total number of received DHCP server discovery packets.
C64 dhcpOffer	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.2	Counter64	read-only	The total number of received DHCP server offer packets.
C64 dhcpRequest	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.3	Counter64	read-only	The total number of received DHCP IP request packets.
DisplayString (44)
STR aclProfileRuleName	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.1	DisplayString	read-only	Profile rule name
STR aclSetProfileName	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.3	DisplayString	read-only	ACL Profile name
STR adslAlarmProfileForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.6	DisplayString	read-write	The ADSL alarm profile.
STR adslLineProfileForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.5	DisplayString	read-write	The ADSL line profile.
STR alarmCurrDescr	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.14	DisplayString	read-only	The description of the alarm.
STR alarmCurrTimeDescr	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.12	DisplayString	read-only	The string representation of occurence time (YYYY/MM/DD HH:MM:SS).
STR dhcpRelay82Info	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.5	DisplayString	read-create	User specific Option82 information.
STR dhcpRelay82Suboption2Info	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.9	DisplayString	read-create	User specified information for Option 82 sub-option 2.
STR dhcpRelayTestStatus	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.4	DisplayString	read-only	Display testing server status.
STR dtpvcAcName	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.11	DisplayString	read-create	Access concentrator name for paepvc.
STR dtpvcDSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.7	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in DS side.
STR dtpvcServiceName	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.12	DisplayString	read-create	Service name for paepvc.
STR dtpvcStateChannelType	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.8	DisplayString	read-only	The value of this object identifies the channel type at runtime.
STR dtpvcStateEncap	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.9	DisplayString	read-only	The value of this object identifies the channel encapsulation at runtime.
STR dtpvcUSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.8	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in US side.
STR extAlarmname	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.2	DisplayString	read-write	The external alarm name.
STR extAlarmstatus	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.3	DisplayString	read-only	Dispaly 'Normal' or 'Alarm' string
STR fwUpgradeStatus	1.3.6.1.4.1.6321.1.2.3.1.11.14.3	DisplayString	read-only	Display current firmware upgrade status.
STR igmpProfileName	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.1	DisplayString	read-only	The IGMP Profile name.
STR mvlanName	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.2	DisplayString	read-create	An administratively assigned string, which may be used to identify the VLAN.
STR paepvcAcName	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.7	DisplayString	read-create	Access concentrator name.
STR paepvcProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.6	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
STR paepvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.11	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
STR paepvcServiceName	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.8	DisplayString	read-create	Service name.
STR paepvcSessionacname	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.6	DisplayString	read-only	Access concentrator name.
STR paepvcSessionsrvcname	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.7	DisplayString	read-only	Service name.
STR pppoeAgentInfo	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.2	DisplayString	read-create	User specific Option82 information.
STR ppvcMemberProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.4	DisplayString	read-create	The profile of the member ppvc in DS side.
STR ppvcMemberProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.6	DisplayString	read-create	The profile of the member ppvc in US side.
STR pvcAcName	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.11	DisplayString	read-create	Access concentrator name for paepvc.
STR pvcProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.6	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
STR pvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.8	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
STR pvcServiceName	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.12	DisplayString	read-create	Service name for paepvc.
STR pvcStateChannelType	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.8	DisplayString	read-only	The value of this object identifies the channel type at runtime.
STR pvcStateEncap	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.9	DisplayString	read-only	The value of this object identifies the channel encapsulation at runtime.
STR rpvcDSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.3	DisplayString	read-create	The down stream profile of the rpvc.
STR rpvcUSProfile	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.4	DisplayString	read-create	The up stream profile of the rpvc.
STR seltStatus	1.3.6.1.4.1.6321.1.2.3.1.4.3.3	DisplayString	read-only	Status description of the selt result.
STR subrPortName	1.3.6.1.4.1.6321.1.2.3.1.8.1.1.1	DisplayString	read-write	Name of the subscriber.
STR subrPortTel	1.3.6.1.4.1.6321.1.2.3.1.8.1.1.2	DisplayString	read-write	Telephone number of the subscriber.
STR tlspvcProfileDS	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.6	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
STR tlspvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.8	DisplayString	read-create	The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
STR userName	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.1	DisplayString	read-only	The user name.
STR userPassword	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.2	DisplayString	read-create	The user password.
INTEGER (310)
INT aclProfileActionNumber	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.3	INTEGER	read-write	Profile action number. Bit 1: rate Bit 2: rvlan Bit 3: rpri Bit 4: deny Bit 1, Bit 2 & Bit 3 can multiple selection.
INT aclProfileActionRate	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.21	INTEGER	read-write	Profile action to replace to this rate
INT aclProfileActionrpri	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.23	INTEGER	read-write	Profile action to replace to this priority
INT aclProfileActionrvlan	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.22	INTEGER	read-write	Profile action to replace to this vlan
INT aclProfileRuleDestEndPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.20	INTEGER	read-write	Profile rule destination end port
INT aclProfileRuleDestIPMask	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.14	INTEGER	read-write	The subnet mask of dest IP mask
INT aclProfileRuleDestStartPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.19	INTEGER	read-write	Profile rule destination start port
INT aclProfileRuleEndTos	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.16	INTEGER	read-write	Profile rule end type of service
INT aclProfileRuleEtype	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.5	INTEGER	read-write	Profile rule etype
INT aclProfileRuleNumber	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.2	INTEGER	read-write	The managed object is for acl profile rule configuration. etype vlan (1), etype smac (2), etype dmac (3), vlan smac (4), vlan dmac (5), smac dmac (6), vlan priority (7), etype (8), vlan (9), smac (10), dmac (11), priority (12), protocol (13), {srcip /{\|dstip /{\|tos {\|srcport {\|dstport }}}}} (14)
INT aclProfileRuleParamMask	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.4	INTEGER	read-write	Profile rule parameter mask. BIT 1: srcip / BIT 2: dstip / BIT 3: tos BIT 4: srcport BIT 5: dstport
INT aclProfileRulePriority	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.9	INTEGER	read-write	Profile rule priority
INT aclProfileRuleProtocol	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.10	INTEGER	read-write	Profile rule protocol. icmp(1),igmp(2),ip(4),tcp(6), udp(17),gre(47),ospf(89), other ptype
INT aclProfileRuleSrcEndPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.18	INTEGER	read-write	Profile rule source end port
INT aclProfileRuleSrcIPMask	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.12	INTEGER	read-write	The subnet mask of source IP mask
INT aclProfileRuleSrcStartPort	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.17	INTEGER	read-write	Profile rule source start port
INT aclProfileRuleStartTos	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.15	INTEGER	read-write	Profile rule start type of service
INT aclProfileRuleVid	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.6	INTEGER	read-write	Profile rule vid
INT aclSetVci	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.2	INTEGER	read-only	VCI value
INT aclSetVpi	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.1	INTEGER	read-only	VPI value
INT adslAtucInpForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.15	INTEGER	read-write	The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslAtucMaxTxPowerForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.9	INTEGER	read-write	The maximum allowed transmit power of ATU-C.
INT adslAturInpForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.14	INTEGER	read-write	The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslAturMaxTxPowerForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.8	INTEGER	read-write	The maximum allowed transmit power of ATU-R.
INT adslL0TimeForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.16	INTEGER	read-write	Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslL0toL2RateForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.22	INTEGER	read-write	configured transition L0 to L2 rate. (= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
INT adslL2ATPRForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.18	INTEGER	read-write	Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslL2ATPRTForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.19	INTEGER	read-write	the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslL2TimeForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.17	INTEGER	read-write	Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslLineConfAdslMode	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.1	INTEGER	read-write	G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
INT adslLineConfAnnexI	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.4	INTEGER	read-write	Enable/disable annex I for the port(For BCM AnnexA solution).
INT adslLineConfAnnexL	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.2	INTEGER	read-write	Enable/disable annex L for the port(Only in AnnexA).
INT adslLineConfAnnexM	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.3	INTEGER	read-write	Enable/disable annex M for the port(For BCM AnnexA solution).
INT adslLineConfAtucInp	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.15	INTEGER	read-write	The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslLineConfAtucMaxTxPower	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.9	INTEGER	read-write	The maximum allowed transmit power of ATU-C.
INT adslLineConfAturInp	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.14	INTEGER	read-write	The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
INT adslLineConfAturMaxTxPower	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.8	INTEGER	read-write	The maximum allowed transmit power of ATU-R.
INT adslLineConfDSPhyr	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.25	INTEGER	read-write	Enable/disable Downstream PHYR for the port(For BCM solution).
INT adslLineConfL0Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.16	INTEGER	read-write	Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslLineConfL0toL2Rate	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.22	INTEGER	read-write	configured transition L0 to L2 rate. (= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
INT adslLineConfL2ATPR	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.18	INTEGER	read-write	Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslLineConfL2ATPRT	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.19	INTEGER	read-write	the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).
INT adslLineConfL2Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.17	INTEGER	read-write	Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.
INT adslLineConfMaxL2Rate	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.20	INTEGER	read-write	configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
INT adslLineConfMaxRxPower	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.10	INTEGER	read-write	The maximum aggregate received power.
INT adslLineConfMinL2Rate	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.21	INTEGER	read-write	configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
INT adslLineConfNitro	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.23	INTEGER	read-write	Enable/disable nitro mode for the port(For BCM solution).
INT adslLineConfOptionMask	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.5	INTEGER	read-write	The semantic for each bit is: BIT 1 : Disable Trellis BIT 2 : Disable Reed-Solomon BIT 3 : Disable upstream bitswap BIT 4 : Disable downstream bitswap BIT 5 : Disable 1-bit constellation BIT 6 : Disable transmit windowing BIT 7 : Disable s=0.5 support (ADSL1 only) BIT 8 : Disable G.lite rate limit (ADSL1 only) BIT 9 : Enable Nitro BIT 10: Enable US PHYR BIT 11: ENABLE DS PHYR
INT adslLineConfPowerMgmt	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.6	INTEGER	read-write	Enable/disable power management for the port.
INT adslLineConfPowerMode	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.7	INTEGER	read-write	The power mode of the ADSL line.
INT adslLineConfUSPhyr	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.24	INTEGER	read-write	Enable/disable Upstream PHYR for the port(For BCM solution).
INT adslLineStatusMode	1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.1	INTEGER	read-only	The link up mode of the ADSL line.
INT adslLineUpTime	1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.2	INTEGER	read-only	The link up time of the ADSL line, in unit of seconds
INT adslMaxL2RateForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.20	INTEGER	read-write	configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
INT adslMaxRxPowerForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.10	INTEGER	read-write	The maximum aggregate received power.
INT adslMinL2RateForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.21	INTEGER	read-write	configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
INT adslModeForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.4	INTEGER	read-write	G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
INT adslOptionMaskForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.7	INTEGER	read-write	The semantic for each bit is identical to the object adslLineConfOptionMask.
INT adslPortOps	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.2	INTEGER	read-write	The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: set ADSL mode BIT 4: set line profile BIT 5: set alarm profile BIT 6: enable Annex L to be narrow mode(Only in AnnexA) BIT 7: enable Annex L to be wide mode(Only in AnnexA) BIT 8: disable Annex L(Only in AnnexA) BIT 9: enable Annex M (For BCM AnnexA solution) BIT 10: disable Annex M (For BCM AnnexA solution) BIT 11: enable Annex I (For BCM AnnexA solution) BIT 12: disable Annex I (For BCM AnnexA solution) BIT 13: set option mask BIT 14: enable power management mode to be L2 BIT 15: enable power management mode to be L2 BIT 16: disable power management mode BIT 17: set power mode to be fixed BIT 18: set power mode to be priority to power BIT 19: set power mode to be priority to rate BIT 20: set ATU-R max Tx power BIT 21: set ATU-C max Tx power BIT 22: set max Rx power BIT 23: set ATU-R carrier mask BIT 24: set ATU-C carrier mask BIT 25: set ATU-R INP minimum setting BIT 26: set ATU-C INP minimum setting
INT adslPortOps2	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.3	INTEGER	read-write	The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: set L0 Time BIT 2: set L2 Time BIT 3: set L2 ATPR BIT 4: set L2 ATPRT BIT 5: set maximum L2 rate BIT 6: set minimum L2 rate BIT 7: set transition L0 to L2 rate
INT adslPortUtilRx	1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.2	INTEGER	read-only	Measure adsl port's rx utilization.
INT adslPortUtilTx	1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.1	INTEGER	read-only	Measure adsl port's tx utilization.
INT alarmConfClearable	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.5	INTEGER	read-write	Setting the object to one indicates that the alarm is to be cleared when user submits alarm clear.
INT alarmConfFacility	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.2	INTEGER	read-write	Alarm facility.
INT alarmConfId	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.1	INTEGER	read-only	5000:adslLine_up 5001:adslLine_down 5002:adslPerf_lol_thresh 5003:adslPerf_lof_thresh 5004:adslPerf_los_thresh 5005:adslPerf_lop_thresh 5006:adslPerf_es_thresh 5007:adslPerf_ses_thresh 5008:adslPerf_uas_thresh 5009:adslAtuc_loftrap 5010:adslAtuc_lostrap 5011:adslAtur_loftrap 5012:adslAtur_lostrap 5013:adslAtur_lprtrap 5014:ad_dhcp_rt_full 5015:ad_dhcp_dm_conflict 5016:ad_dhcp_entry_full 5017:ad_dhcp_ip_dup 5018:ad_dhcp_mac_dup 10000:eqptVol_err 10001:eqptEqpttemp_err 10002:eqptFan_err 10003:eqptHw_rtc_fail 10004:eqptHw_mon_fail 10005:eqptCold_start 10006:eqptWarm_start 10007:eqptAlm_input 10008:eqptI2c_err 10009:eqptAlm_input2 10010:eqptAlm_input3 15000:sysReboot 15001:sysAco 15002:sysAlm_clear 15003:sysLogin_fail 15004:sysAnti_spoofing 15005:sysAlm_svrty_change 20000:enetUp 20001:enetDown
INT alarmConfSeverity	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.4	INTEGER	read-write	Alarm severity
INT alarmConfTarget	1.3.6.1.4.1.6321.1.2.3.1.2.2.1.3	INTEGER	read-write	The destination which alarms are reported to. Set the bit to 1 to enable the target. BIT 1: snmp trap BIT 2: syslog
INT alarmCurrIndex	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.1	INTEGER	read-only	Index of the alarm.
INT alarmCurrParam1	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.4	INTEGER	read-only	The 1st parameter of the alarm.
INT alarmCurrParam2	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.5	INTEGER	read-only	The 2nd parameter of the alarm.
INT alarmCurrParam3	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.6	INTEGER	read-only	The 3rd parameter of the alarm.
INT alarmCurrParam4	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.7	INTEGER	read-only	The 4th parameter of the alarm.
INT alarmCurrParam5	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.8	INTEGER	read-only	The 5th parameter of the alarm.
INT alarmCurrParam6	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.9	INTEGER	read-only	The 6th parameter of the alarm.
INT alarmCurrParam7	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.10	INTEGER	read-only	The 7th parameter of the alarm.
INT alarmCurrParam8	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.11	INTEGER	read-only	The 8th parameter of the alarm.
INT alarmCurrSeverity	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.13	INTEGER	read-only	The severity of the alarm.
INT alarmOps	1.3.6.1.4.1.6321.1.2.3.1.2.1	INTEGER	read-write	The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: clear BIT 2: cutoff
INT arpproxyAge	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.1	INTEGER	read-write	Aging time of the ARP proxy. This object is supported by R3.00 and later versions.
INT arpproxyDhcpIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.9	INTEGER	read-only
INT arpproxyFlushInterfaceMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.6	INTEGER	read-write	Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
INT arpproxyFlushOps	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.2	INTEGER	read-write	Set the object to 1 to start flushing. This object is supported by R3.00 and later versions.
INT arpproxyFlushTarget	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.1	INTEGER	read-write	The target whose ARP table to be flushed. This object is supported by R3.00 and later versions.
INT arpproxyIfIndex	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.3	INTEGER	read-only
INT arpproxyInterfaceMask	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.7	INTEGER	read-only
INT arpproxyType	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.10	INTEGER	read-only
INT arpproxyVci	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.5	INTEGER	read-only
INT arpproxyVpi	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.4	INTEGER	read-only
INT auditQryEnable	1.3.6.1.4.1.6321.1.2.3.1.7.12.1	INTEGER	read-write	Enable/disable IGMP audit query.
INT auditQryInterval	1.3.6.1.4.1.6321.1.2.3.1.7.12.2	INTEGER	read-write	Set IGMP Audit Query Interval, 1~4 in 100 milliseconds.
INT auditQryRobust	1.3.6.1.4.1.6321.1.2.3.1.7.12.3	INTEGER	read-write	Set IGMP Audit Query Robustness, 1~5.
INT counterClearOps	1.3.6.1.4.1.6321.1.2.3.1.14.2	INTEGER	read-write	The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: clear interface counters BIT 2: clear pvc packet counters BIT 3: clear port ATM counters BIT 4: clear pvc ATM counters BIT 5: clear DHCP counters BIT 6: clear IGMP counters BIT 7: clear IGMP port counters BIT 8: clear MACFF ARP counters BIT 9: clear current lineperf BIT 10: clear current 15 minute lineperf BIT 11: clear current 1 day lineperf
INT counterClearVci	1.3.6.1.4.1.6321.1.2.3.1.14.4	INTEGER	read-write	VCI of the pvc whose counters would be cleared.
INT counterClearVpi	1.3.6.1.4.1.6321.1.2.3.1.14.3	INTEGER	read-write	VPI of the pvc whose counters would be cleared.
INT currNumOfMacFiltersInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.53.4	INTEGER	read-only	The current number of mac filters in the system.
INT delayedRebootCancel	1.3.6.1.4.1.6321.1.2.3.1.11.15.3	INTEGER	read-write	cancel the scheduled reboot.
INT delayedRebootRemainingTime	1.3.6.1.4.1.6321.1.2.3.1.11.15.2	INTEGER	read-only	Display the remaining time of scheduled reboot.
INT delayedRebootTimer	1.3.6.1.4.1.6321.1.2.3.1.11.15.1	INTEGER	read-write	5~1800 secs, 0: reboot immediately.
INT dhcpRelay82ActiveServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.3	INTEGER	read-only	The current active DHCP Relay server.
INT dhcpRelay82Enable	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.4	INTEGER	read-create	Enable/disable DHCP relay and Option82 function.
INT dhcpRelay82EntryEnable	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.10	INTEGER	read-create	Enable/disable DHCP Relay
INT dhcpRelay82EntryOptionMode	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.11	INTEGER	read-create	Option82 format.
INT dhcpRelay82RelayMode	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.6	INTEGER	read-create	DHCP relay mode.
INT dhcpRelay82ServerVid	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.18	INTEGER	read-write	The VID of the DHCP Relay server for this VLAN.
INT dhcpRelay82Suboption2Enable	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.8	INTEGER	read-create	Enable/disable Option 82 sub-option 2.
INT dhcpRelay82VlanMask	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.13	INTEGER	read-write	The network mask of the DHCP Relay interface for this VLAN.
INT dhcpRelayArpFlushOps	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.2	INTEGER	read-write	Set the object to 1 to start flushing.
INT dhcpRelayArpShowVid	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.1	INTEGER	read-only	Display the VID of the DHCP ARP entry.
INT dhcpRelayTestOps	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.3	INTEGER	read-write	Set the object to 1 to test DHCP server.
INT dhcpRelayTestVid	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.1	INTEGER	read-write	Setting the VID of the test server.
INT dhcpRouteIndex	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.1	INTEGER	read-only
INT dhcpRouteMask	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.4	INTEGER	read-only	The subnet mask of source IP mask.
INT dhcpSnoopEnable	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.1	INTEGER	read-write	Enable/disable DHCP snooping for a port.
INT dhcpSnoopMask	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.4	INTEGER	read-only	The snooped IP mask
INT dhcpSnoopMaxcnt	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.2	INTEGER	read-write	Set the max entries of the DHCP ARP table.
INT dhcpSnoopMaxcntMode	1.3.6.1.4.1.6321.1.2.3.1.10.55.6	INTEGER	read-write	When DHCP snooping table is full, new DHCP lease will replace first one in option 0 or will be dropped in option 1.
INT dhcpSnoopOps	1.3.6.1.4.1.6321.1.2.3.1.10.55.3	INTEGER	read-write	The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: DHCP snooping table flush.
INT dhcpSnoopSmacverifyEnable	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.3	INTEGER	read-write	Enable/disable DHCP source MAC verify for a port.
INT dsBcastCtrlEnable	1.3.6.1.4.1.6321.1.2.3.1.11.11.1	INTEGER	read-write	Enable/disable downstream broadcast control.
INT dsBcastCtrlRate	1.3.6.1.4.1.6321.1.2.3.1.11.11.2	INTEGER	read-write	32~1000000 in step of 32 kbps
INT dsBcastDisableVlanId	1.3.6.1.4.1.6321.1.2.3.1.8.9.1.1	INTEGER	read-only	downstream broadcast disabled vid.
INT dscpMapPriority	1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.3	INTEGER	read-write	The mapping p bits that will replace the source p bits in the incoming packet.
INT dscpSrcCodePoint	1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.1	INTEGER	read-only	The DSCP source code point used for mapping.
INT dscpStatusEnable	1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1.1	INTEGER	read-write	The DSCP port status.
INT dslRateLatencyMode	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.2	INTEGER	read-only	The latency mode is fast or interleave
INT dslRateMode	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.1	INTEGER	read-write	Configure DSL Rate configuration mode of the specified ports. Profile: the DSL Rate configuration comes from DSL profile. Line: the DSL Rate configuration comes from line configuration.
INT dslRateXtucMaxInterleaveDelay	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.3	INTEGER	read-write	Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
INT dslRateXturMaxInterleaveDelay	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.6	INTEGER	read-write	Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency
INT dtpvcCpriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.6	INTEGER	read-create	c-tag priority of the pvc.
INT dtpvcHelloTime	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.13	INTEGER	read-create	The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
INT dtpvcSpriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.4	INTEGER	read-create	s-tag priority of the pvc.
INT dtpvcStateCPriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.6	INTEGER	read-only	C-priority of the dtpvc.
INT dtpvcStateSPriority	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.4	INTEGER	read-only	S-priority of the dtpvc.
INT dtpvcStateVci	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.2	INTEGER	read-only	VCI of the dtpvc.
INT dtpvcStateVpi	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.1	INTEGER	read-only	VPI of the dtpvc.
INT dtpvcSuperChannel	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.10	INTEGER	read-create	Specified the configured DTPVC is a super channel.
INT dtpvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.2	INTEGER	read-only	VCI of the pvc.
INT dtpvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.1	INTEGER	read-only	VPI of the pvc.
INT enetMtuEntry	1.3.6.1.4.1.6321.1.2.3.1.10.13.1	INTEGER	read-write	Sets the MTU size for layer 2 frame, size from 1526 to 1532, default value is 1526.
INT enetSfpInfoRxpower	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.2	INTEGER	read-only	Measured Rx Output Power.
INT enetSfpInfoTemperature	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.3	INTEGER	read-only	Measured temperature.
INT enetSfpInfoTxBias	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.4	INTEGER	read-only	Measured tx bias.
INT enetSfpInfoTxpower	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.1	INTEGER	read-only	Measured Tx Output Power.
INT enetSfpInfoVoltage	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.5	INTEGER	read-only	Measured voltage.
INT extAlarmIndex	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.1	INTEGER	read-only	The index of the entry.
INT extAlarmTriggeredMode	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.4	INTEGER	read-write	The external alarm triggered mode.
INT fwUpgradeCheck	1.3.6.1.4.1.6321.1.2.3.1.11.14.2	INTEGER	read-write	Enable/disable firmware upgrade version checking feature.
INT igmpCountPortEnable	1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.1	INTEGER	read-write	Enable/disable IGMP count limiting for a port.
INT igmpCountPortLimit	1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.2	INTEGER	read-write	The maximum allowed IGMP report count for a port.
INT igmpEnable	1.3.6.1.4.1.6321.1.2.3.1.7.1	INTEGER	read-write	Enable/disable IGMP protocol.
INT igmpFilterIndex	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.1	INTEGER	read-only	The index which specifies the filter rule.
INT igmpGroupnumberOfMembers	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.3	INTEGER	read-only	number Of Members
INT igmpGroupPortvid	1.3.6.1.4.1.6321.1.2.3.1.13.6.1.2	INTEGER	read-only	Igmp Group vid
INT igmpGroupV2NumOfMembers	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.3	INTEGER	read-only	The number of member ports in the group.
INT igmpGroupvid	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.2	INTEGER	read-only	vlan id
INT igmpLastMemQryInterval	1.3.6.1.4.1.6321.1.2.3.1.7.11.4	INTEGER	read-write	Set IGMP Last Member Query interval, 1~5 in 100 milliseconds.
INT igmpLastMemQryRobust	1.3.6.1.4.1.6321.1.2.3.1.7.11.5	INTEGER	read-write	Set Last Member Query Robustness, 1~5.
INT igmpLeaveMode	1.3.6.1.4.1.6321.1.2.3.1.7.10	INTEGER	read-write	Configure IGMP leave message handling mode.
INT igmpNumOfActiveGroups	1.3.6.1.4.1.6321.1.2.3.1.13.4	INTEGER	read-only	The total number of IGMP learned groups.
INT igmpPortNumOfActiveGroups	1.3.6.1.4.1.6321.1.2.3.1.13.9.1.4	INTEGER	read-only	The total number of active IGMP groups in this port.
INT igmpProfileEnable	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.2	INTEGER	read-write	Enable/disable IGMP Profile.
INT igmpProfileMaxGroup	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.3	INTEGER	read-write	Set maximum allowed multicast group, 1~16.
INT igmpQryInterval	1.3.6.1.4.1.6321.1.2.3.1.7.11.1	INTEGER	read-write	Set IGMP query interval, 10~1000 in seconds.
INT igmpQryRespInterval	1.3.6.1.4.1.6321.1.2.3.1.7.11.3	INTEGER	read-write	Set IGMP query response interval, 1~100 in 100 milliseconds.
INT igmpRobust	1.3.6.1.4.1.6321.1.2.3.1.7.11.2	INTEGER	read-write	Set IGMP query Robustness, 1~5.
INT igmpVersion	1.3.6.1.4.1.6321.1.2.3.1.7.9	INTEGER	read-write	Setting IGMP version.
INT ipbpvcDomainDhcpVlanEnable	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.2	INTEGER	read-create	Enable/disable DHCP VLAN in a domain.
INT ipbpvcEdgeRouterMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.3	INTEGER	read-only	Netmask of the edge router.
INT ipbpvcEncap	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.4	INTEGER	read-create	Type of the PVC.
INT ipbpvcIfDynamicIfIndex	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.3	INTEGER	read-only
INT ipbpvcIfDynamicMask	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.2	INTEGER	read-only
INT ipbpvcIfDynamicVci	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.5	INTEGER	read-only
INT ipbpvcIfDynamicVpi	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.4	INTEGER	read-only
INT ipbpvcInterfaceIfIndex	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.4	INTEGER	read-create	IfIndex of the interface.
INT ipbpvcInterfaceMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.2	INTEGER	read-only	Netmask of the interface.
INT ipbpvcInterfaceVci	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.6	INTEGER	read-create	VCI of the interface.
INT ipbpvcInterfaceVpi	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.5	INTEGER	read-create	VPI of the interface.
INT ipbpvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.5	INTEGER	read-create	Priority of the PVC.
INT ipbpvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.3	INTEGER	read-only	PVID of the PVC.
INT ipbpvcRouteDynamicMask	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.3	INTEGER	read-only
INT ipbpvcRouteDynamicMetric	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.5	INTEGER	read-only
INT ipbpvcRouteDynamicPriority	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.6	INTEGER	read-only
INT ipbpvcRouteDynamicType	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.1	INTEGER	read-only
INT ipbpvcRouteMask	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.2	INTEGER	read-only	Netmask of the route.
INT ipbpvcRouteMetric	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.4	INTEGER	read-create	Metric of the route.
INT ipbpvcRoutePriority	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.5	INTEGER	read-create	Priority of the route. Note that the default value of this object is 8, which means we keep the original priority of the packet(frame).
INT ipbpvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.7	INTEGER	read-create	Row status of the table used to create/delete an entry.
INT ipbpvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.2	INTEGER	read-only	VCI of the PVC.
INT ipbpvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.1	INTEGER	read-only	VPI of the PVC.
INT isConfigChanged	1.3.6.1.4.1.6321.1.2.3.1.11.13	INTEGER	read-only	If system configuration has been changed.
INT macDisplayTarget	1.3.6.1.4.1.6321.1.2.3.1.13.13.1	INTEGER	read-write	This managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. The target could be: 99: all ports in the system 98: all subscriber ports 97: all Ethernet ports IfIndex is used for identifying subscriber ports and Ethernet Ports(e.g. 1 ~ 50).
INT macFfArpFlush	1.3.6.1.4.1.6321.1.2.3.1.10.60.3	INTEGER	read-write	Set the object to 1 to flush mac table.
INT macFfArpPort	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.3	INTEGER	read-only	Port of this AR/AS.
INT macFfIndex	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.1	INTEGER	read-only	Index of the MACFF.
INT macFfSrcMask	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.5	INTEGER	read-write	The subnet mask of source IP mask.
INT macFfStaticIPMask	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.4	INTEGER	read-only	Mask_bits is 24 .. 32.
INT macFfStaticIPPort	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.1	INTEGER	read-only	The port number, 1 ~ 48.
INT macFfStaticIPVid	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.2	INTEGER	read-only	VLAN ID of the IP range, 1 ~ 4094, the vid should be enable the MACFF function first.
INT macFfStatsIndex	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.1	INTEGER	read-only	Index of the MACFF.
INT macFfStatsSrcMask	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.5	INTEGER	read-only	The subnet mask of source IP mask.
INT macFfVid	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.2	INTEGER	read-write	The VLAN-ID refering to this AR/AS.
INT macFfVlanUnknownUnicast	1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.2	INTEGER	read-create	Setting downstream unknown uni-cast packet on macff vlan to flooding or dropping.
INT macFilterMacCountForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.10.53.6.3	INTEGER	read-write	The total number of MAC addresses allowed for a port.
INT macfilterOps	1.3.6.1.4.1.6321.1.2.3.1.10.53.6.2	INTEGER	read-write	The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable mac filter BIT 2: enable mac count filter BIT 3: disable mac filter BIT 4: set mac count BIT 5: disable mac count filter.
INT macFilterPortEnable	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.1	INTEGER	read-write	Enable/disable MAC filtering for the port.
INT macFilterPortFilterMode	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.3	INTEGER	read-write	The mac filter mode (accept or deny) for the port.
INT macFilterPortMacCount	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.2	INTEGER	read-write	The total number of MAC addresses allowed for the port.
INT macPort	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.2	INTEGER	read-only	The port from which the mac address has been learned.
INT macStatus	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.3	INTEGER	read-only	The status of this entry.
INT maxNumberOfIgmpProfiles	1.3.6.1.4.1.6321.1.2.3.1.7.13.1	INTEGER	read-only	The max number of IGMP profiles in the system.
INT maxNumOfDhcpStaticIp	1.3.6.1.4.1.6321.1.2.3.1.10.55.5	INTEGER	read-only	The maximum number of DHCP static IP addresses which can be created for a port.
INT maxNumOfMacFfVlanInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.60.4	INTEGER	read-only	The max number of macff Vlans supported in the system.
INT maxNumOfMacFiltersInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.53.2	INTEGER	read-only	The max number of mac filters supported in the system.
INT maxNumOfMacFiltersPerPort	1.3.6.1.4.1.6321.1.2.3.1.10.53.3	INTEGER	read-only	The max number of mac filters supported per port.
INT maxNumOfMcastBw	1.3.6.1.4.1.6321.1.2.3.1.7.4.2	INTEGER	read-only	The maximum number of row entries that user can create in mcastBwTable.
INT maxNumOfMvlan	1.3.6.1.4.1.6321.1.2.3.1.7.6.1	INTEGER	read-only	The maximum number of row entries that user can create in mvlanTable.
INT maxNumOfOuiFiltersInSystem	1.3.6.1.4.1.6321.1.2.3.1.10.53.10	INTEGER	read-only	The max number of OUI filters supported in system.
INT maxNumOfOuiFiltersPerPort	1.3.6.1.4.1.6321.1.2.3.1.10.53.8	INTEGER	read-only	The max number of OUI filters supported per port.
INT maxNumOfOuiFiltersPerVlan	1.3.6.1.4.1.6321.1.2.3.1.10.53.11	INTEGER	read-only	The max number of OUI filters supported per vlan.
INT maxNumOfPppoeDhcpRelay82Conf	1.3.6.1.4.1.6321.1.2.3.1.10.57.2	INTEGER	read-only	The maximum number of rows that can be created in pppoeAgentTable.
INT maxNumOfPriorityPvcs	1.3.6.1.4.1.6321.1.2.3.1.8.5.1	INTEGER	read-only	The maximum number of priority PVCs which could be created on a port.
INT maxNumOfPvcs	1.3.6.1.4.1.6321.1.2.3.1.8.4.1	INTEGER	read-only	The maximum number of PVCs which could be created on a port.
INT maxNumOfQryVid	1.3.6.1.4.1.6321.1.2.3.1.7.7.1	INTEGER	read-only	The maximum number of row entries that user can create in qryVidConfTable.
INT mcastBwBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.4	INTEGER	read-create	The bandwidth budget for the multicast IP channels.
INT mcastBwIndex	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.1	INTEGER	read-only	The index which specify the entry.
INT mcastBwPortBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.2	INTEGER	read-write	Set bandwidth threshold for a port.
INT mcastBwPortEnable	1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.1	INTEGER	read-write	Enable/disable multicast bandwidth control for a port.
INT mcastDefaultBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4.1	INTEGER	read-write	Default bandwidth requirement for a multicast channel.
INT mvlanTranslateIndex	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.1	INTEGER	read-only	The index which specif the entry.
INT ouiFilterPortEnable	1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.1	INTEGER	read-write	Enable/disable oui filtering for the port.
INT ouiFilterPortFilterMode	1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.2	INTEGER	read-write	The oui filter mode (accept or deny) for the port.
INT ouiFilterVlanEnable	1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.1	INTEGER	read-write	Enable/disable oui filtering for the VLAN.
INT ouiFilterVlanFilterMode	1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.2	INTEGER	read-write	The oui filter mode (accept or deny) for the VLAN.
INT paepvcCountVci	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.2	INTEGER	read-only	The PAEPVC VCI.
INT paepvcCountVpi	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.1	INTEGER	read-only	The PAEPVC VPI.
INT paepvcCPriority	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.13	INTEGER	read-create	802.1p default C-priority of the pvc.
INT paepvcHelloTime	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.9	INTEGER	read-create	The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
INT paepvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.5	INTEGER	read-create	802.1p default priority of the pvc.
INT paepvcSessionId	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.4	INTEGER	read-only	The PAEPVC session ID.
INT paepvcSessionState	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.3	INTEGER	read-only	The PAEPVC status.
INT paepvcSessionVci	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.2	INTEGER	read-only	The PAEPVC VCI.
INT paepvcSessionVpi	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.1	INTEGER	read-only	The PAEPVC VPI.
INT paepvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.2	INTEGER	read-only	VCI of the pvc.
INT paepvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.1	INTEGER	read-only	VPI of the pvc.
INT powerMgmtAtucMaxPSD	1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.1	INTEGER	read-write	The object specifies the maximum ATU-C PSD.
INT powerMgmtAturMaxPSD	1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.2	INTEGER	read-write	The object specifies the maximum ATU-R PSD.
INT powerMgmtL0Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.1	INTEGER	read-write	The object specifies the minimum time in L0 mode before L2 mode may be entered.
INT powerMgmtL2Atpr	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.3	INTEGER	read-write	The maximum Aggregate Transmit Power Reduction.
INT powerMgmtL2Atprt	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.4	INTEGER	read-write	The maximum Aggregate Transmit Power Reduction Total.
INT powerMgmtL2MaxRate	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.6	INTEGER	read-write	The object specifies the maximum L2 rate.
INT powerMgmtL2MinRate	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.5	INTEGER	read-write	The object specifies the minimum L2 rate.
INT powerMgmtL2ThreshRate	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.7	INTEGER	read-write	The object specifies the rate threshold that triggers the line entering L0 or L2 mode.
INT powerMgmtL2Time	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.2	INTEGER	read-write	The object specifies the minimum time in L2 mode before trimming and in between power trims.
INT pppoeAgentEnable	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.1	INTEGER	read-create	Enable/disable DHCP relay and Option82 function.
INT pppoeAgentOptionMode	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.4	INTEGER	read-create	Option82 format.
INT ppvcEncap	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.4	INTEGER	read-create	Encapsulation of the ppvc.
INT ppvcMemberPriority	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.3	INTEGER	read-only	802.1p default priority of the member ppvc.
INT ppvcMemberVci	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.2	INTEGER	read-only	VCI of the member ppvc.
INT ppvcMemberVpi	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.1	INTEGER	read-only	VPI of the member ppvc.
INT ppvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.5	INTEGER	read-create	802.1p default priority of the ppvc.
INT ppvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.2	INTEGER	read-only	VCI of the ppvc.
INT ppvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.1	INTEGER	read-only	VPI of the ppvc.
INT pvcHelloTime	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.13	INTEGER	read-create	The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
INT pvcPriority	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.5	INTEGER	read-create	802.1p default priority of the pvc.
INT pvcStatePriority	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.4	INTEGER	read-only	802.1p default priority of the pvc.
INT pvcStateVci	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.2	INTEGER	read-only	VCI of the pvc.
INT pvcStateVpi	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.1	INTEGER	read-only	VPI of the pvc.
INT pvcUsRateLimit	1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.2	INTEGER	read-write	Upstream rate limit in Kbps for a PVC.
INT pvcUsRateLimitEnable	1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.1	INTEGER	read-write	Enable/disable upstream rate limit for a PVC.
INT pvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.2	INTEGER	read-only	VCI of the pvc.
INT pvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.1	INTEGER	read-only	VPI of the pvc.
INT qryVid	1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.1	INTEGER	read-only	VLAN ID.
INT qryVidType	1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1.1	INTEGER	read-only	VLAN type.
INT rpvcArpAgingTime	1.3.6.1.4.1.6321.1.2.3.1.8.8.4	INTEGER	read-write	Set RPVC ARP proxy aging time 10..10000 seconds, 0 to disable againg.
INT rpvcArpFlush	1.3.6.1.4.1.6321.1.2.3.1.8.8.5	INTEGER	read-write	Flush the RPVC ARP proxy table.
INT rpvcGatewayPriority	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.4	INTEGER	read-write	802.1p p bit send to this RPVC gateway.
INT rpvcRouteDomainVci	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.2	INTEGER	read-only	VCI of the rpvc.
INT rpvcRouteDomainVpi	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.1	INTEGER	read-only	VPI of the rpvc.
INT rpvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.2	INTEGER	read-only	VCI of the rpvc.
INT rpvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.1	INTEGER	read-only	VPI of the rpvc.
INT securedClientEnable	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.5	INTEGER	read-write	Enable/disable the entry.
INT securedClientIndex	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.1	INTEGER	read-only	The index of the entry.
INT securedClientService	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.4	INTEGER	read-write	Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1: telnet BIT 2: ftp BIT 3: web BIT 4: icmp BIT 5: not support BIT 6: snmp.
INT seltCableType	1.3.6.1.4.1.6321.1.2.3.1.4.3.4	INTEGER	read-only	The cable type that selt result indicates.
INT seltLoopEstimateLengthFt	1.3.6.1.4.1.6321.1.2.3.1.4.3.5	INTEGER	read-only	The estimated loop length that selt result indicates.
INT seltLoopEstimateLengthMeter	1.3.6.1.4.1.6321.1.2.3.1.4.3.6	INTEGER	read-only	The estimated loop length that selt result indicates.
INT seltOps	1.3.6.1.4.1.6321.1.2.3.1.4.3.2	INTEGER	read-write	The manager sets the object to 1 to start the selt and the agent clears the object to zero when selt is successfully completed.
INT seltTarget	1.3.6.1.4.1.6321.1.2.3.1.4.3.1	INTEGER	read-write	IfIndex of the port which would be performed single end loopback test.
INT severityThresh	1.3.6.1.4.1.6321.1.2.3.1.2.4.1.1	INTEGER	read-write	The minimum alarm severity that is reported.
INT snrMgnMode	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.1	INTEGER	read-write	Configure DSL SNR margin configuration mode of the specified ports. Profile: the SNR margin configuration comes from DSL profile. Line: the SNR margin configuration comes from line configuration.
INT snrMgnUcDownshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.5	INTEGER	read-write	Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
INT snrMgnUcMax	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.3	INTEGER	read-write	Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
INT snrMgnUcMin	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.4	INTEGER	read-write	Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
INT snrMgnUcTarget	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.2	INTEGER	read-write	Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
INT snrMgnUcUpshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.6	INTEGER	read-write	Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
INT snrMgnUrDownshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.10	INTEGER	read-write	Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
INT snrMgnUrMax	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.8	INTEGER	read-write	Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
INT snrMgnUrMin	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.9	INTEGER	read-write	Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
INT snrMgnUrTarget	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.7	INTEGER	read-write	Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
INT snrMgnUrUpshift	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.11	INTEGER	read-write	Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
INT stdioTimeout	1.3.6.1.4.1.6321.1.2.3.1.11.12	INTEGER	read-write	Set the CLI/TELNET/WEB Session timeout, 0, or 1~300 minutes, 0 => disable.
INT tlspvcSpriority	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.5	INTEGER	read-create	s-tag priority of the pvc.
INT tlspvcVci	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.2	INTEGER	read-only	VCI of the pvc.
INT tlspvcVpi	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.1	INTEGER	read-only	VPI of the pvc.
INT usBcastCtrlEnable	1.3.6.1.4.1.6321.1.2.3.1.11.10.1	INTEGER	read-write	Enable/disable upstream broadcast control.
INT usBcastCtrlRate	1.3.6.1.4.1.6321.1.2.3.1.11.10.2	INTEGER	read-write	32~49984 in step of 32kbps
INT userAuthDefaultPriviledge	1.3.6.1.4.1.6321.1.2.3.1.11.9.6	INTEGER	read-write	The user default priviledge to be assigned when radius authentication succeds but no user priviledge information(radius service-type) is provided.
INT userAuthMode	1.3.6.1.4.1.6321.1.2.3.1.11.9.1	INTEGER	read-write	User authentication procsssing mode.
INT userAuthServerPort	1.3.6.1.4.1.6321.1.2.3.1.11.9.3	INTEGER	read-write	The port of the authentication server.
INT userPriviledge	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.3	INTEGER	read-create	The user priviledge to decide what operation the user can and cannot do.
IpAddress (53)
IP aclProfileRuleDestIP	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.13	IpAddress	read-write	Profile rule source IP
IP aclProfileRuleSrcIP	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.11	IpAddress	read-write	Profile rule source IP
IP arpproxyFlushEdgeRouterIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.3	IpAddress	read-write	Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
IP arpproxyFlushInterfaceIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.5	IpAddress	read-write	Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
IP arpproxyInterfaceIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.6	IpAddress	read-only
IP arpproxyIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.1	IpAddress	read-only
IP dhcpRelay82FifthServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.17	IpAddress	read-write	The IP address of the DHCP Relay fifth server.
IP dhcpRelay82FourthServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.16	IpAddress	read-write	The IP address of the DHCP Relay fourth server.
IP dhcpRelay82PrimaryServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.1	IpAddress	read-write	The IP address of the DHCP Relay primary server.
IP dhcpRelay82SecondaryServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.2	IpAddress	read-write	The IP address of the DHCP Relay secondary server.
IP dhcpRelay82ThirdServer	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.15	IpAddress	read-write	The IP address of the DHCP Relay third server.
IP dhcpRelay82VlanGateway	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.14	IpAddress	read-write	The gateway of the DHCP Relay interface for this VLAN.
IP dhcpRelay82VlanIp	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.12	IpAddress	read-write	The IP address of the DHCP Relay interface for this VLAN.
IP dhcpRelayArpShowIp	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.2	IpAddress	read-only	Display the IP of the DHCP ARP entry.
IP dhcpRelayTestIp	1.3.6.1.4.1.6321.1.2.3.1.10.51.8.2	IpAddress	read-write	Setting the IP of the test server.
IP dhcpRouteGwIP	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.5	IpAddress	read-only	The gateway IP address.
IP dhcpRouteIP	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.3	IpAddress	read-only	IP of this dhcp route
IP dhcpSnoopGateway	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.5	IpAddress	read-only	The snooped Gateway.
IP dhcpSnoopIp	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.1	IpAddress	read-only	The snooped IP address.
IP dhcpStaticIpAddr	1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.1	IpAddress	read-only	The IP address which can pass through the port.
IP igmpFilterEndIp	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.3	IpAddress	read-create	The end IP of the filter rule.
IP igmpFilterStartIp	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.2	IpAddress	read-create	The start IP of the filter rule.
IP igmpGroupIp	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.1	IpAddress	read-only	igmp group IP
IP igmpGroupPortIp	1.3.6.1.4.1.6321.1.2.3.1.13.6.1.1	IpAddress	read-only	Igmp Group IP
IP igmpGroupPortV2Ip	1.3.6.1.4.1.6321.1.2.3.1.13.8.1.2	IpAddress	read-only	The multicast IP address.
IP igmpGroupPortV2SourceIp	1.3.6.1.4.1.6321.1.2.3.1.13.8.1.3	IpAddress	read-only	The source IP address that joins the IGMP group.
IP igmpGroupV2Ip	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.2	IpAddress	read-only	The multicast IP address.
IP ipbpvcEdgeRouterIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.1	IpAddress	read-only	IP address of the edge router.
IP ipbpvcIfDynamicIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.1	IpAddress	read-only
IP ipbpvcInterfaceIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.1	IpAddress	read-only	IP address of the interface.
IP ipbpvcRouteDynamicIp	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.2	IpAddress	read-only
IP ipbpvcRouteDynamicNextHop	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.4	IpAddress	read-only
IP ipbpvcRouteIp	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.1	IpAddress	read-only	IP address of the route.
IP ipbpvcRouteNextHop	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.3	IpAddress	read-only	Next hop IP address of the route.
IP macFfArIP	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.3	IpAddress	read-write	IP of this AR/AS
IP macFfArpIP	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.2	IpAddress	read-only	IP of this AR/AS.
IP macFfSrcIP	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.4	IpAddress	read-write	The source IP address of the MACFF.
IP macFfstaticIP	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.3	IpAddress	read-only	The specified IP range.
IP macFfStatsArIP	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.3	IpAddress	read-only	IP of this AR/AS
IP macFfStatsSrcIP	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.4	IpAddress	read-only	The source IP address of the MACFF.
IP mcastBwEndIp	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.3	IpAddress	read-only	The end multicast IP of the bandwidth control range.
IP mcastBwStartIp	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.2	IpAddress	read-only	The start multicast IP of the bandwidth control range.
IP mvlanTranslateEndIp	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.3	IpAddress	read-write	The end IP of the multicast VLAN translation.
IP mvlanTranslateStartIp	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.2	IpAddress	read-write	The start IP of the multicast VLAN translation.
IP rpvcGatewayIp	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.1	IpAddress	read-only	IP of RPVC gateway.
IP rpvcGatewayIpAddress	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.7	IpAddress	read-create	The gateway IP of rpvc.
IP rpvcIp	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.5	IpAddress	read-only	The IP of the rpvc.
IP rpvcNetmask	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.6	IpAddress	read-only	The IP mask of the rpvc IP.
IP rpvcRouteDomainIp	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.3	IpAddress	read-only	The route domain IP.
IP rpvcRouteDomainNetmask	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.4	IpAddress	read-only	The IP mask of the route domain IP.
IP securedClientEndIp	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.3	IpAddress	read-write	The ending IP address of the secured client set.
IP securedClientStartIp	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.2	IpAddress	read-write	The starting IP address of the secured client set.
IP userAuthServerIp	1.3.6.1.4.1.6321.1.2.3.1.11.9.2	IpAddress	read-write	The IP address of the authentication server.
MacAddress (2)
MAC arpproxyMac	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.2	MacAddress	read-only
MAC macAddress	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.1	MacAddress	read-only	A unicast MAC address for which the bridge has forwarding and/or filtering information.
OBJECT IDENTIFIER (1)
OID alarmCurrTrapOid	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.3	OBJECT IDENTIFIER	read-only	Trap OID of the alarm.
OCTET STRING (21)
OCT adslAtucCarrierMask0ForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.12	OCTET STRING	read-write	The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates the bin is masked off.
OCT adslAtucCarrierMask1ForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.13	OCTET STRING	read-write	The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
OCT adslAturCarrierMaskForBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.11	OCTET STRING	read-write	The upstream carrier mask.For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off.
OCT adslLineConfAtucCarrierMask0	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.12	OCTET STRING	read-write	The downstream carrier mask. For CTLM AnnexA solution, bin is from 32 to 255; CTLM AnnexB solution, bin is from 64 to 255; BCM solution, bin is from 32 to 255. Bit set to 1 indicates the bin is masked off.
OCT adslLineConfAtucCarrierMask1	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.13	OCTET STRING	read-write	The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
OCT adslLineConfAturCarrierMask	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.11	OCTET STRING	read-write	The upstream carrier mask. For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off.
OCT adslPortTarget	1.3.6.1.4.1.6321.1.2.3.1.8.2.3.1	OCTET STRING	read-write	The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chaises) Byte 2~3: 0,0 Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
OCT counterClearTarget	1.3.6.1.4.1.6321.1.2.3.1.14.1	OCTET STRING	read-write	This managed object is used for identify the target on which the counter would be cleared. The target is encoded as: Byte 1: reserved Byte 2~3: reserved Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
OCT dhcpSnoopRouteMap	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.6	OCTET STRING	read-only	The refrence bit map of the dhcp route
OCT dhcpSnoopTarget	1.3.6.1.4.1.6321.1.2.3.1.10.55.2	OCTET STRING	read-write	This managed object is used for identify the target on which the operation should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
OCT fwUpgradeVersion	1.3.6.1.4.1.6321.1.2.3.1.11.14.1	OCTET STRING	read-write	Configure the target firmware version that will be upgraded.
OCT gbondGroupName	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.1	OCTET STRING	read-only	An administratively assigned string, which may be used to identify bonding group.
OCT gbondGroupPorts	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.2	OCTET STRING	read-create	The set of ports which are currently assigned to the bonding group of specified group name. Byte 1: Reserved(chassis) Byte 2~3: Reserved(slot) Byte 4: Reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
OCT igmpProfilePortProfile	1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1.1	OCTET STRING	read-write	The IGMP Profile of the port.
OCT ipbpvcDomainName	1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.1	OCTET STRING	read-only	Name of the domain.
OCT ipbpvcProfile	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.6	OCTET STRING	read-create	Profile of the PVC.
OCT ipbpvcProfileUS	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.8	OCTET STRING	read-create	US Profile of the PVC.
OCT macfilterTarget	1.3.6.1.4.1.6321.1.2.3.1.10.53.6.1	OCTET STRING	read-write	This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chassis) Byte 2~3: 0, Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
OCT ouiFilterAddr	1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.1	OCTET STRING	read-only	The first three bytes of the mac address which can pass through or be rejected from the vlan.
OCT ouiFilterAddrOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.1	OCTET STRING	read-only	The first three bytes of the mac address which can pass through or be rejected from the port.
OCT userAuthServerSecret	1.3.6.1.4.1.6321.1.2.3.1.11.9.4	OCTET STRING	read-write	The secret between the authentication server and the NE for authentication process.
PhysAddress (6)
PHY aclProfileRuleDmac	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.8	PhysAddress	read-write	Profile rule destination MAC
PHY aclProfileRuleSmac	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.7	PhysAddress	read-write	Profile rule source MAC
PHY dhcpRelayArpShowMac	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.3	PhysAddress	read-only	Display the MAC of the DHCP ARP entry.
PHY dhcpSnoopMac	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.2	PhysAddress	read-only	The snooped MAC address.
PHY macFfArpMac	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.4	PhysAddress	read-only	MAC address of the AR or AS.
PHY macFilterAddr	1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.1	PhysAddress	read-only	The mac address which can pass through or be rejected from the port.
PortList (4)
POR igmpGroupMemberPorts	1.3.6.1.4.1.6321.1.2.3.1.13.5.1.4	PortList	read-only	Group Member Ports
POR igmpGroupV2MemberPorts	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.4	PortList	read-only	The member port list of the group.
POR mvlanEgressPorts	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.3	PortList	read-create	The set of ports which are permanently assigned to the egress list for this multicast VLAN.
POR mvlanUntaggedPorts	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.4	PortList	read-create	The set of ports which should transmit egress packets for this multicast VLAN as untagged.
RowStatus (32)
ROW aclProfileRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.24	RowStatus	read-write	The row status of the entry.
ROW aclSetRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.4	RowStatus	read-write	RowStatus of aclSetEntry
ROW dhcpStaticRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.2	RowStatus	read-create	Row status of the table entry.
ROW dsBcastDisableRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.9.1.2	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ROW dtpvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.9	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ROW gbondGroupRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.6	RowStatus	read-create	This object indicates the status of this entry.
ROW igmpProfileRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.4	RowStatus	read-create	The row status of the IGMP Profile entry.
ROW ipbpvcDomainRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.2	RowStatus	read-create	Row status of the table.
ROW ipbpvcDomainVlanRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.3	RowStatus	read-create	Row status of the table used to create/delete an entry.
ROW ipbpvcEdgeRouterRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.4	RowStatus	read-create	Row status of the table used to create/delete an entry.
ROW ipbpvcInterfaceRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.7	RowStatus	read-create	Row status of the table used to create/delete an entry.
ROW ipbpvcRouteRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.6	RowStatus	read-create	Row status of the table used to create/delete an entry.
ROW macFfRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.6	RowStatus	read-create	The row status of the MacFfEntry entry.
ROW macFfStaticIPRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.5	RowStatus	read-create	The row status used to configure the table entry.
ROW macFfVlanRowstatus	1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.1	RowStatus	read-create	Row status of the table used to create/delete an entry.
ROW macFilterRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.2	RowStatus	read-create	The row status of the entry.
ROW mcastBwRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.5	RowStatus	read-create	The row status of the entry.
ROW mvlanRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.5	RowStatus	read-create	This object indicates the status of this entry.
ROW ouiFilterRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.2	RowStatus	read-create	The row status of the entry.
ROW ouiFilterRowStatusOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.2	RowStatus	read-create	The row status of the entry.
ROW paepvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.10	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ROW pppoeAgentRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.3	RowStatus	read-create	Row status of the table entry.
ROW ppvcMemberRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.5	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ROW ppvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.6	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ROW pvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.7	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ROW qryVidRowStatus	1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.2	RowStatus	read-create	This object indicates the status of this entry.
ROW rpvcGatewayRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.3	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ROW rpvcRouteDomainRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.5	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ROW rpvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.8	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ROW tlspvcRowStatus	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.7	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ROW userRowStatus	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.4	RowStatus	read-create	The row status used to create or delete a user.
ROW vlanIsolationRowStatus	1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1.1	RowStatus	read-create	Row status of the table used to create/delete an entry.
TimeTicks (1)
TIK alarmCurrOccurTime	1.3.6.1.4.1.6321.1.2.3.1.2.3.1.2	TimeTicks	read-only	Alarm occurence time (in hundredths of a second) since the system was last re-initialized.
Unsigned32 (20)
U32 dslRateXtucMaxTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.4	Unsigned32	read-write	Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
U32 dslRateXtucMinTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.5	Unsigned32	read-write	Configured Minimum Transmit rate for `Fast' or `Interleave' channels, in bps
U32 dslRateXturMaxTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.7	Unsigned32	read-write	Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
U32 dslRateXturMinTxRate	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.8	Unsigned32	read-write	Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
U32 gbondGroupDownRate	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.5	Unsigned32	read-only	The DOWN stream rate.
U32 gbondGroupUpRate	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.4	Unsigned32	read-only	The UP stream rate.
U32 paepvcCountAcSystemErrRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.13	Unsigned32	read-only	The number of pppoe access concentrator name error received
U32 paepvcCountGenericErrRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.15	Unsigned32	read-only	The number of pppoe generic error received
U32 paepvcCountGenericErrTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.14	Unsigned32	read-only	The number of pppoe generic error transfered
U32 paepvcCountPadiTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.6	Unsigned32	read-only	The number of pppoe padi transfered
U32 paepvcCountPadoRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.7	Unsigned32	read-only	The number of pppoe pado received
U32 paepvcCountPadrTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.8	Unsigned32	read-only	The number of pppoe padr transfered
U32 paepvcCountPadsRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.9	Unsigned32	read-only	The number of pppoe pads received
U32 paepvcCountPadtRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.11	Unsigned32	read-only	The number of pppoe padt received
U32 paepvcCountPadtTx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.10	Unsigned32	read-only	The number of pppoe padt transfered
U32 paepvcCountPppLcpCfgReqRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.3	Unsigned32	read-only	The number of ppp lcp config-request received.
U32 paepvcCountPppLcpEchoReplyRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.5	Unsigned32	read-only	The number of ppp lcp echo-reply received.
U32 paepvcCountPppLcpEchoReqRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.4	Unsigned32	read-only	The number of ppp lcp echo-request received.
U32 paepvcCountSrvcnameErrRx	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.12	Unsigned32	read-only	The number of pppoe service name error received
U32 paepvcSessionUptime	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.5	Unsigned32	read-only	The PAEPVC session uptime.
VlanIndex (24)
VLA arpproxyFlushEdgeRouterVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.4	VlanIndex	read-write	Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
VLA arpproxyFlushInterfaceVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.7	VlanIndex	read-write	Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
VLA arpproxyInterfaceVid	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.8	VlanIndex	read-only
VLA dhcpRouteVid	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.2	VlanIndex	read-only	The VLAN-ID refering to this dhcp route.
VLA dhcpSnoopVid	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.3	VlanIndex	read-only	The snooped VLAN ID.
VLA dtpvcCvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.5	VlanIndex	read-create	c-tag VLAN ID of the pvc.
VLA dtpvcStateCvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.5	VlanIndex	read-only	Default C-VID of the dtpvc.
VLA dtpvcStateSvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.3	VlanIndex	read-only	Default S-VID of the dtpvc.
VLA dtpvcSvid	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.3	VlanIndex	read-only	s-tag VLAN ID of the pvc.
VLA igmpGroupPortV2Vid	1.3.6.1.4.1.6321.1.2.3.1.13.8.1.1	VlanIndex	read-only	The IGMP group VLAN ID.
VLA igmpGroupV2Vid	1.3.6.1.4.1.6321.1.2.3.1.13.7.1.1	VlanIndex	read-only	The IGMP group VLAN ID.
VLA ipbpvcDomainVlanId	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.1	VlanIndex	read-only	Set VLAN to join or leave the specified domain.
VLA ipbpvcEdgeRouterVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.2	VlanIndex	read-only	VLAN ID of the edge router.
VLA ipbpvcInterfaceVid	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.3	VlanIndex	read-only	VLAN ID of the interface.
VLA macFfArpVid	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.1	VlanIndex	read-only	The VLAN-ID refering to this AR/AS.
VLA macFfStatsVid	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.2	VlanIndex	read-only	The VLAN-ID refering to this AR/AS.
VLA mvlanIndex	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.1	VlanIndex	read-only	The VLAN-ID refering to this VLAN.
VLA paepvcCvid	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.12	VlanIndex	read-create	Default C-VID of the pvc.
VLA paepvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.3	VlanIndex	read-only	Default VID of the pvc.
VLA ppvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.3	VlanIndex	read-only	Default VID of the ppvc.
VLA pvcPvid	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.3	VlanIndex	read-only	Default VID of the pvc.
VLA pvcStatePvid	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.3	VlanIndex	read-only	Default VID of the pvc.
VLA rpvcGatewayVlanId	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.2	VlanIndex	read-write	Vlan id send to this RPVC gateway.
VLA tlspvcSvid	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.3	VlanIndex	read-only	s-tag VLAN ID of the pvc.
No type (227)
accessCtrl	1.3.6.1.4.1.6321.1.2.3.1.11.5
accessSwitchCommonATM	1.3.6.1.4.1.6321.1.2.3.1.99
acl	1.3.6.1.4.1.6321.1.2.3.1.10.56
aclProfileEntry	1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1		not-accessible	An entry of aclProfileTable.
aclProfileTable	1.3.6.1.4.1.6321.1.2.3.1.10.56.2		not-accessible	aclProfileTable.
aclSetEntry	1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1		not-accessible	An entry of aclSetTable.
aclSetTable	1.3.6.1.4.1.6321.1.2.3.1.10.56.1		not-accessible	aclsetTable.
adslLineConfEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1		not-accessible	An entry in adslLineConfTable.
adslLineConfTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.1		not-accessible	This table includes common attributes describing the ADSL line.
adslLineStatusEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1		not-accessible	An entry in adslLineStatusTable.
adslLineStatusTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.4		not-accessible	This table includes the ADSL line status.
adslPort	1.3.6.1.4.1.6321.1.2.3.1.8.2
adslPortBatchSet	1.3.6.1.4.1.6321.1.2.3.1.8.2.3
adslPortUtilEntry	1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1		not-accessible	An entry in adslPortUtilEntry.
adslPortUtilTable	1.3.6.1.4.1.6321.1.2.3.1.13.18.1		not-accessible	This table includes adsl port utilization.
adslStats	1.3.6.1.4.1.6321.1.2.3.1.13.18
aesSeriesCommon	1.3.6.1.4.1.6321.1.2.3.1.97
alarmconf	1.3.6.1.4.1.6321.1.2.3.1.2
alarmConfEntry	1.3.6.1.4.1.6321.1.2.3.1.2.2.1		not-accessible	An entry in alarmConfTable.
alarmConfTable	1.3.6.1.4.1.6321.1.2.3.1.2.2		not-accessible	This table includes alarm configuration.
alarmCurrEntry	1.3.6.1.4.1.6321.1.2.3.1.2.3.1		not-accessible	An entry in alarmCurrTable.
alarmCurrTable	1.3.6.1.4.1.6321.1.2.3.1.2.3		not-accessible	This table includes current alarm information.
alarmSeverityPortEntry	1.3.6.1.4.1.6321.1.2.3.1.2.4.1		not-accessible	An entry in alarmSeverityPortTable.
alarmSeverityPortTable	1.3.6.1.4.1.6321.1.2.3.1.2.4		not-accessible	This table includes the configuration of alarm reporting severity threshold for each port.
arpproxy	1.3.6.1.4.1.6321.1.2.3.1.8.12.8
arpproxyEntry	1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1		not-accessible	An entry of arpproxyTable.
arpproxyFlush	1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2
arpproxyTable	1.3.6.1.4.1.6321.1.2.3.1.13.14.1		not-accessible	Display ARP table. This table is supported by R3.00 and later versions.
auditQuery	1.3.6.1.4.1.6321.1.2.3.1.7.12
calixNetworks	1.3.6.1.4.1.6321
calixProducts	1.3.6.1.4.1.6321.1.2
calixRegistrations	1.3.6.1.4.1.6321.1
clear	1.3.6.1.4.1.6321.1.2.3.1.14
delayedReboot	1.3.6.1.4.1.6321.1.2.3.1.11.15
dhcp	1.3.6.1.4.1.6321.1.2.3.1.10.51
dhcpRelay82Entry	1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1		not-accessible	The entry of DHCP Relay table.
dhcpRelay82Table	1.3.6.1.4.1.6321.1.2.3.1.10.51.2		not-accessible	A table that contains DHCP Relay configuration.
dhcpRelayArp	1.3.6.1.4.1.6321.1.2.3.1.10.51.9
dhcpRelayArpShowEntry	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1		not-accessible	An entry of dhcpRelayArpShowTable.
dhcpRelayArpShowTable	1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1		not-accessible	The table displays DHCP ARP.
dhcpRelayTest	1.3.6.1.4.1.6321.1.2.3.1.10.51.8
dhcpRouteEntry	1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1		not-accessible	An entry of dhcpRouteTable.
dhcpRouteTable	1.3.6.1.4.1.6321.1.2.3.1.13.11.3		not-accessible	A table that contains dhcp route information.
dhcpSnoop	1.3.6.1.4.1.6321.1.2.3.1.10.55
dhcpSnoopCounterEntry	1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1		not-accessible	An entry of dhcpSnoopCounterTable.
dhcpSnoopCounterTable	1.3.6.1.4.1.6321.1.2.3.1.13.11.2		not-accessible	This table shows the DHCP statistics.
dhcpSnoopIpEntry	1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1		not-accessible	An entry of dhcpSnoopIpTable.
dhcpSnoopIpTable	1.3.6.1.4.1.6321.1.2.3.1.13.11.1		not-accessible	This table shows the IP addresses and netmasks offered by the DHCP server.
dhcpSnoopPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1		not-accessible	An entry of dhcpSnoopPortTable.
dhcpSnoopPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.55.1		not-accessible	This table includes DHCP snooping enable/disable for each port.
dhcpStaticEntry	1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1		not-accessible	An entry of dhcpStaticTable.
dhcpStaticTable	1.3.6.1.4.1.6321.1.2.3.1.10.55.4		not-accessible	This table defines DHCP static IP addresses.
dhcpStats	1.3.6.1.4.1.6321.1.2.3.1.13.11
diagnostic	1.3.6.1.4.1.6321.1.2.3.1.4
dsbCastCtrl	1.3.6.1.4.1.6321.1.2.3.1.11.11
dsBcastDisableEntry	1.3.6.1.4.1.6321.1.2.3.1.8.9.1		not-accessible	An entry in Down Stream Bcast table.
dsBcastDisableTable	1.3.6.1.4.1.6321.1.2.3.1.8.9		not-accessible	This table includes Down Stream Bcast configuration.
dscp	1.3.6.1.4.1.6321.1.2.3.1.10.10
dscpMappingEntry	1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1		not-accessible	An entry of dscpMappingTable.
dscpMappingTable	1.3.6.1.4.1.6321.1.2.3.1.10.10.1		not-accessible	The table contains DSCP mapping configuration for the adsl and ethernet ports.
dscpPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1		not-accessible	An entry of dscpPortTable.
dscpPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.10.2		not-accessible	The table contains DSCP mapping configuration for the adsl and ethernet ports.
dslRate	1.3.6.1.4.1.6321.1.2.3.1.8.16
dslRateEntry	1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1		not-accessible	An entry of dslRateTable.
dslRateTable	1.3.6.1.4.1.6321.1.2.3.1.8.16.1		not-accessible	A table containing the per port DSL Rate configuration.
dtpvc	1.3.6.1.4.1.6321.1.2.3.1.8.14
dtpvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1		not-accessible	An entry of dtpvcTable.
dtpvcStateEntry	1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1		not-accessible	An entry in dtpvcStateTable.
dtpvcStateTable	1.3.6.1.4.1.6321.1.2.3.1.8.14.2		not-accessible	This table show current DTPVC status.
dtpvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.14.1		not-accessible	This table includes Double Tagging (DT) PVC configuration.
e5x100	1.3.6.1.4.1.6321.1.2.3
e5x110	1.3.6.1.4.1.6321.1.2.3.1
enetMtu	1.3.6.1.4.1.6321.1.2.3.1.10.13
enetSfpInfoEntry	1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1		not-accessible	An entry in enetSfpInfoTable.
enetSfpInfoTable	1.3.6.1.4.1.6321.1.2.3.1.13.17.2		not-accessible	This table includes sfp info of enet port.
enetStats	1.3.6.1.4.1.6321.1.2.3.1.13.17
extAlarm	1.3.6.1.4.1.6321.1.2.3.1.11.8
extAlarmEntry	1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1		not-accessible	The entry of external alarm table.
extAlarmTable	1.3.6.1.4.1.6321.1.2.3.1.11.8.1		not-accessible	A table that contains external alarm information.
fwUpgrade	1.3.6.1.4.1.6321.1.2.3.1.11.14
gbond	1.3.6.1.4.1.6321.1.2.3.1.8.51
gbondGroupEntry	1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1		not-accessible	An entry of gbondTable.
gbondGroupTable	1.3.6.1.4.1.6321.1.2.3.1.8.51.1		not-accessible	A table containing the G.Bond configuration information for each bonding group of the device.
iesSeriesCommon	1.3.6.1.4.1.6321.1.2.3.1.98
igmpCount	1.3.6.1.4.1.6321.1.2.3.1.7.5
igmpCountPortEntry	1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1		not-accessible	An entry of igmpCountPortTable.
igmpCountPortTable	1.3.6.1.4.1.6321.1.2.3.1.7.5.1		not-accessible	This table specify the IGMP count limiting of the port.
igmpFilterEntry	1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1		not-accessible	The entry of IGMP Filter table.
igmpFilterTable	1.3.6.1.4.1.6321.1.2.3.1.7.13.3		not-accessible	A table that contains IGMP Filters.
igmpGroupEntry	1.3.6.1.4.1.6321.1.2.3.1.13.5.1		not-accessible	An entry in igmpGroupTable.
igmpGroupPortEntry	1.3.6.1.4.1.6321.1.2.3.1.13.6.1		not-accessible	An entry in igmpGroupPortTable.
igmpGroupPortTable	1.3.6.1.4.1.6321.1.2.3.1.13.6		not-accessible	This table includes igmp Group port information.
igmpGroupPortV2Entry	1.3.6.1.4.1.6321.1.2.3.1.13.8.1		not-accessible	An entry of igmpGroupPortV2Table.
igmpGroupPortV2Table	1.3.6.1.4.1.6321.1.2.3.1.13.8		not-accessible	A table that displays IGMP joined groups in this port.
igmpGroupTable	1.3.6.1.4.1.6321.1.2.3.1.13.5		not-accessible	This table includes igmp group information.
igmpGroupV2Entry	1.3.6.1.4.1.6321.1.2.3.1.13.7.1		not-accessible	An entry of igmpGroupV2Table.
igmpGroupV2Table	1.3.6.1.4.1.6321.1.2.3.1.13.7		not-accessible	A table that displays IGMP learned group member information.
igmpPortCtrlPduEntry	1.3.6.1.4.1.6321.1.2.3.1.13.9.1		not-accessible	An entry of igmpPortCtrlPduTable.
igmpPortCtrlPduTable	1.3.6.1.4.1.6321.1.2.3.1.13.9		not-accessible	A table that displays IGMP related counter values in this port.
igmpProfile	1.3.6.1.4.1.6321.1.2.3.1.7.13
igmpProfileEntry	1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1		not-accessible	The entry of IGMP Profile table.
igmpProfilePortEntry	1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1		not-accessible	An entry in igmpProfilePortTable.
igmpProfilePortTable	1.3.6.1.4.1.6321.1.2.3.1.7.13.4		not-accessible	This table specifies the IGMP Profile of the port.
igmpProfileTable	1.3.6.1.4.1.6321.1.2.3.1.7.13.2		not-accessible	A table that contains IGMP Profiles.
igmpTimer	1.3.6.1.4.1.6321.1.2.3.1.7.11
ipbpvc	1.3.6.1.4.1.6321.1.2.3.1.8.12
ipbpvcDomainEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1		not-accessible	An entry of ipbpvcDomainTable.
ipbpvcDomainTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.1		not-accessible	This table includes ipbpvc domain configuration. This table is supported by R3.00 and later versions.
ipbpvcDomainVlanEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1		not-accessible	An entry of ipbpvcDomainVlanTable.
ipbpvcDomainVlanTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.2		not-accessible	This table includes ipbpvc domain VLAN configuration. This table is supported by R3.00 and later versions.
ipbpvcEdgeRouterEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1		not-accessible	An entry of ipbpvcEdgeRouterTable.
ipbpvcEdgeRouterTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.3		not-accessible	This table includes ipbpvc edge router configuration. This table is supported by R3.00 and later versions.
ipbpvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1		not-accessible	An entry of ipbpvcTable.
ipbpvcIfDynamicEntry	1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1		not-accessible	An entry of ipbpvcIfDynamicTable.
ipbpvcIfDynamicTable	1.3.6.1.4.1.6321.1.2.3.1.13.14.2		not-accessible	Display runtime interfaces. This table is supported by R3.00 and later versions.
ipbpvcInterfaceEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1		not-accessible	An entry of ipbpvcInterfaceTable.
ipbpvcInterfaceTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.4		not-accessible	This table includes ipbpvc interface configuration. This table is supported by R3.00 and later versions.
ipbpvcRouteDynamicEntry	1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1		not-accessible	An entry of ipbpvcRouteDynamicTable.
ipbpvcRouteDynamicTable	1.3.6.1.4.1.6321.1.2.3.1.13.14.3		not-accessible	Display runtime routing table. This table is supported by R3.00 and later versions.
ipbpvcRouteEntry	1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1		not-accessible	An entry of ipbpvcRouteTable.
ipbpvcRouteTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.5		not-accessible	This table includes ipbpvc route configuration. This table is supported by R3.00 and later versions.
ipbpvcStats	1.3.6.1.4.1.6321.1.2.3.1.13.14
ipbpvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.12.6		not-accessible	This table includes ipbpvc configuration. This table is supported by R3.00 and later versions.
macEntry	1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1		not-accessible	An entry of macTable.
macff	1.3.6.1.4.1.6321.1.2.3.1.10.60
macFfArpCounterEntry	1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1		not-accessible	An entry of macFfArpCounterTable.
macFfArpCounterTable	1.3.6.1.4.1.6321.1.2.3.1.13.16.3		not-accessible	A table that contains MAC Force Forwarding ARP counter information.
macFfArpEntry	1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1		not-accessible	An entry of macFfArpTable.
macFfArpTable	1.3.6.1.4.1.6321.1.2.3.1.13.16.2		not-accessible	A table that contains MAC Force Forwarding ARP information.
macFfEntry	1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1		not-accessible	An entry of macFfTable.
macFfStaticIPEntry	1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1		not-accessible	An entry of macFfTable.
macFfStaticIPTable	1.3.6.1.4.1.6321.1.2.3.1.10.60.6		not-accessible
macffStats	1.3.6.1.4.1.6321.1.2.3.1.13.16
macFfStatsEntry	1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1		not-accessible	An entry of macFfStatsTable.
macFfStatsTable	1.3.6.1.4.1.6321.1.2.3.1.13.16.1		not-accessible	A table that contains MAC Force Forwarding static configuration and dynamic information.
macFfTable	1.3.6.1.4.1.6321.1.2.3.1.10.60.1		not-accessible	A table that contains MAC Force Forwarding configuration.
macFfVlanEntry	1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1		not-accessible	An entry of macFfVlanTable.
macFfVlanTable	1.3.6.1.4.1.6321.1.2.3.1.10.60.5		not-accessible	A table that contains MAC Force Forwarding Vlan configuration.
macfilter	1.3.6.1.4.1.6321.1.2.3.1.10.53
macfilterBatchSet	1.3.6.1.4.1.6321.1.2.3.1.10.53.6
macFilterEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1		not-accessible	The entry of macFilterTable.
macFilterPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1		not-accessible	An entry in macFilterPortTable.
macFilterPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.1		not-accessible	This table includes the status of mac filtering for each port.
macFilterTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.5		not-accessible	A table that contains the mac filter addresses.
macStats	1.3.6.1.4.1.6321.1.2.3.1.13.13
macTable	1.3.6.1.4.1.6321.1.2.3.1.13.13.2		not-accessible	A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
mcastBandwidth	1.3.6.1.4.1.6321.1.2.3.1.7.4
mcastBwEntry	1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1		not-accessible	An entry of mcastBwTable.
mcastBwPortEntry	1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1		not-accessible	An entry of mcastBwPortTable.
mcastBwPortTable	1.3.6.1.4.1.6321.1.2.3.1.7.4.4		not-accessible	This table specify the multicast bandwidth control of the port.
mcastBwTable	1.3.6.1.4.1.6321.1.2.3.1.7.4.3		not-accessible	This table defines bandwidth budget for a range of multicast IP channels.
multicast	1.3.6.1.4.1.6321.1.2.3.1.7
mvlan	1.3.6.1.4.1.6321.1.2.3.1.7.6
mvlanEntry	1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1		not-accessible	An entry of mvlanTable.
mvlanTable	1.3.6.1.4.1.6321.1.2.3.1.7.6.2		not-accessible	A table containing static configuration information for each multicast VLAN configured into the device.
mvlanTranslateEntry	1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1		not-accessible	An entry of mvlanTranslateTable.
mvlanTranslateTable	1.3.6.1.4.1.6321.1.2.3.1.7.6.3		not-accessible	A table that contains multicast to VLAN translation.
ouiFilterEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1		not-accessible	The entry of ouiFilterTable.
ouiFilterEntryOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1		not-accessible	The entry of ouiFilterTableOld.
ouiFilterPortEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1		not-accessible	An entry in macFilterPortTable.
ouiFilterPortTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.9		not-accessible	This table includes the status of oui filtering for each port.
ouiFilterTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.12		not-accessible	A table that contains the OUI filter addresses.
ouiFilterTableOld	1.3.6.1.4.1.6321.1.2.3.1.10.53.7		not-accessible	A table that contains the OUI filter addresses.
ouiFilterVlanEntry	1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1		not-accessible	An entry in ouiFilterVlanTable.
ouiFilterVlanTable	1.3.6.1.4.1.6321.1.2.3.1.10.53.13		not-accessible	This table includes the status of oui filtering for each configured VLAN.
paepvc	1.3.6.1.4.1.6321.1.2.3.1.8.10
paepvcCountEntry	1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1		not-accessible	An entry of paepvcCountTable.
paepvcCountTable	1.3.6.1.4.1.6321.1.2.3.1.13.12.2		not-accessible	This table shows the paepvc counters.
paepvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1		not-accessible	An entry of paepvcTable.
paepvcSessionEntry	1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1		not-accessible	An entry of paepvcSessionTable.
paepvcSessionTable	1.3.6.1.4.1.6321.1.2.3.1.13.12.1		not-accessible	This table shows the paepvc session statistics.
paepvcStats	1.3.6.1.4.1.6321.1.2.3.1.13.12
paepvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.10.1		not-accessible	This table includes PPPoAoE PVC configuration.
port	1.3.6.1.4.1.6321.1.2.3.1.8
powerMgmtParamEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1		not-accessible	An entry in powerMgmtParamTable.
powerMgmtParamTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.5		not-accessible	This table defines L0 to L2 power transition parameters.
powerMgmtPSDEntry	1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1		not-accessible	An entry in powerMgmtPSDTable.
powerMgmtPSDTable	1.3.6.1.4.1.6321.1.2.3.1.8.2.6		not-accessible	This table provides the PSD setting for both ATU-C and ATU-R.
pppoeAgent	1.3.6.1.4.1.6321.1.2.3.1.10.57
pppoeAgentEntry	1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1		not-accessible	An entry of pppoeAgentTable.
pppoeAgentTable	1.3.6.1.4.1.6321.1.2.3.1.10.57.1		not-accessible	A table that contains PPPoE DHCP Relay configuration.
ppvc	1.3.6.1.4.1.6321.1.2.3.1.8.5
ppvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1		not-accessible	An entry in ppvcTable.
ppvcMemberEntry	1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1		not-accessible	An entry in ppvcMemberTable.
ppvcMemberTable	1.3.6.1.4.1.6321.1.2.3.1.8.5.4		not-accessible	This table includes priority PVC member configuration.
ppvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.5.2		not-accessible	This table includes priority PVC configuration.
pvc	1.3.6.1.4.1.6321.1.2.3.1.8.4
pvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1		not-accessible	An entry in pvcTable.
pvcStateEntry	1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1		read-only	An entry in pvcStateTable.
pvcStateTable	1.3.6.1.4.1.6321.1.2.3.1.8.4.3		read-only	This table show current PVC status.
pvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.4.2		not-accessible	This table includes PVC configuration.
pvcUsRateLimitEntry	1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1		not-accessible	An entry in pvcUsRateLimitTable.
pvcUsRateLimitTable	1.3.6.1.4.1.6321.1.2.3.1.8.4.4		not-accessible	This table defines the upstream rate limit for each PVC.
qryVidConfEntry	1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1		not-accessible	An entry in qryVidConfTable.
qryVidConfTable	1.3.6.1.4.1.6321.1.2.3.1.7.7.2		not-accessible	This table defines statically set VLANs used for response IGMP report.
qryVidStatusEntry	1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1		not-accessible	An entry in qryVidStatusTable.
qryVidStatusTable	1.3.6.1.4.1.6321.1.2.3.1.7.7.3		not-accessible	This table shows statically set or dynamically learned VLANs used for response IGMP report.
queryVid	1.3.6.1.4.1.6321.1.2.3.1.7.7
rpvc	1.3.6.1.4.1.6321.1.2.3.1.8.8
rpvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1		not-accessible	An entry in rpvcTable.
rpvcGatewayEntry	1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1		not-accessible	An entry in Routed Gateway table.
rpvcGatewayTable	1.3.6.1.4.1.6321.1.2.3.1.8.8.1		not-accessible	This table includes Routed Gateway configuration.
rpvcRouteDomainEntry	1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1		not-accessible	An entry in rpvcRouteDomainTable.
rpvcRouteDomainTable	1.3.6.1.4.1.6321.1.2.3.1.8.8.3		not-accessible	This table includes RPVC route domain configuration.
rpvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.8.2		not-accessible	This table includes RPVC configuration.
securedClientEntry	1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1		not-accessible	A list of secured client entry.
securedClientTable	1.3.6.1.4.1.6321.1.2.3.1.11.5.2		not-accessible	A table that contains information about secured clients.
selt	1.3.6.1.4.1.6321.1.2.3.1.4.3
snrMgn	1.3.6.1.4.1.6321.1.2.3.1.8.15
snrMgnEntry	1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1		not-accessible	An entry of snrMgnTable.
snrMgnTable	1.3.6.1.4.1.6321.1.2.3.1.8.15.1		not-accessible	A table containing the per port SNR Margin configuration.
statistics	1.3.6.1.4.1.6321.1.2.3.1.13
subrPortEntry	1.3.6.1.4.1.6321.1.2.3.1.8.1.1		not-accessible	An entry in subrPortTable.
subrPortTable	1.3.6.1.4.1.6321.1.2.3.1.8.1		not-accessible	This table includes subscriber attributes for the port.
switch	1.3.6.1.4.1.6321.1.2.3.1.10
sys	1.3.6.1.4.1.6321.1.2.3.1.11
tlspvc	1.3.6.1.4.1.6321.1.2.3.1.8.11
tlspvcEntry	1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1		not-accessible	An entry of tlspvcTable.
tlspvcTable	1.3.6.1.4.1.6321.1.2.3.1.8.11.1		not-accessible	This table includes Transparent LAN Service (TLS) PVC configuration.
trap	1.3.6.1.4.1.6321.1.2.3.1.12
usbCastCtrl	1.3.6.1.4.1.6321.1.2.3.1.11.10
user	1.3.6.1.4.1.6321.1.2.3.1.11.9
userEntry	1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1		not-accessible	An entry of userTable.
userTable	1.3.6.1.4.1.6321.1.2.3.1.11.9.5		not-accessible	A table that contains user information.
vlanIsolation	1.3.6.1.4.1.6321.1.2.3.1.10.12
vlanIsolationEntry	1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1		not-accessible	An entry of vlanIsolationTable.
vlanIsolationTable	1.3.6.1.4.1.6321.1.2.3.1.10.12.1		not-accessible	A table contains configuration of isolated VLAN.

FAQ

What would a broadband provider monitor on a Calix E5-110 access node using E5-110-MIB?
System-level configuration and status data including chassis/system identification, service provisioning parameters, and access-port operational state, along with system uptime and firmware version as a general health check on the unit.

How does E5-110-MIB help catch faults on an E5-110 access node deployed at the network edge?
It surfaces environmental and fault alarms alongside hardware status and traps, so a provider managing E5-110 nodes in a cabinet or central office can be alerted to card/module presence issues or environmental problems without a truck roll.

RFC description

Core management MIB for the Calix E5-110 multi-service access platform covering system configuration and status.

Start monitoring Calix E5-110 multi-service access platform with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download E5-110-MIB

This MIB depends on

Related MIBs

What Is E5-110-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

FAQ

RFC description