DSR4410MD-MIB

All MIBs › DSR4410MD-MIB

Organization: ARRIS Group INC

Last Updated: 2014-04-23

Category: Domain: Satellite, Vendor: ARRIS

Description: Provides management objects for the DSR4410MD series digital satellite router configuration and monitoring.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DSR4410MD-MIB?

DSR4410MD-MIB is an ARRIS Group vendor-specific MIB (registered under the legacy General Instrument giproducts branch) that models the DSR4410MD, a DigiCipher II / DVB-S/DVB-S2 Integrated Receiver-Decoder (IRD) used to receive and decode satellite video feeds -- despite the hint's description of it as a 'digital satellite router,' the MIB's actual object set is entirely about satellite tuning, decoding, and video/audio output, not IP routing. It exposes RF tuning and lock parameters under manualTune (transponderNumber, frequency, dvbSymbolRate/dvbCodeRate, dvbS2symbolRate/dvbS2codeRate, modulationMode), channel selection and status (vctID, channelNumber, transponder, source, satelliteStatus), alarm configuration (alarmTrigger covering no-signal, no-video, and no-authorization conditions), and audio/data output settings (audio1/2 gain and language objects, subtitleLanguage, ethernet/gigE port IP configuration). This gives an operator a complete view of whether a satellite receiver is locked to its intended transponder, authorized to decode its service, and outputting clean audio/video, which is critical for head-end and affiliate monitoring of broadcast feeds. It uses legacy RFC1155-SMI/SNMPv2-TC conventions and a MODULE-IDENTITY added only in a later revision. It is deployed at cable/broadcast head-ends and affiliate sites receiving satellite-delivered video, and administrators can download the DSR4410MD-MIB file to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DSR4410MD-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ARRIS DSR4410MD satellite Integrated Receiver-Decoder (IRD)

Monitoring Examples

An operator polls channelStatus objects transponder and satelliteStatus to confirm the DSR4410MD is locked to the expected feed, and checks alarmTrigger alongside tvPasscard authorization state; a unit reporting an empty transponder/source string or an active no-signal/no-authorization alarm would indicate the receiver has lost lock or lacks entitlement to decode the selected satellite service.

What Can Be Monitored

RF tuning parameters (transponder/frequency/symbol rate/code rate)
channel and transponder lock/source status
alarm trigger conditions (no-signal/no-video/no-authorization)
service authorization (passcard) state
audio gain, downmix, and language configuration
Ethernet/GigE port IP configuration

Imported Objects

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
accessControl	1.3.6.1.4.1.1166.1.621.9.1
OCT acpAuthState	1.3.6.1.4.1.1166.1.621.15.6	OCTET STRING	read-only	This field displays the authorization status of the ACP for the current Service association. AU -- Authorization NA -- Not Authorized The unit presents dashes when no information is available
OCT acpEncryptMode	1.3.6.1.4.1.1166.1.621.15.7	OCTET STRING	read-only	This field displays the Encryption Mode of the service being decrypted by the selected ACP. The different values are FP - Fixed Program Key FW - Fixed Working Key S - Scrambled ZK - Unencrypted The unit presents dashes when no information is available
INT acpIndex	1.3.6.1.4.1.1166.1.621.15.2	INTEGER	read-write	Number uniquely identifying the ACP and keystream pair.
INT acpKeyStream	1.3.6.1.4.1.1166.1.621.15.5	INTEGER	read-only	The selected keystream.
acpMib	1.3.6.1.4.1.1166.1.621.15
INT acpMode	1.3.6.1.4.1.1166.1.621.15.1	INTEGER	read-write	Setup mode for the authorization control processor.
INT acpProgram	1.3.6.1.4.1.1166.1.621.15.3	INTEGER	read-write	The MPEG service number of the program.
OCT acpUnitAddress	1.3.6.1.4.1.1166.1.621.15.4	OCTET STRING	read-only	The electronic address of the selected ACP in the following format: ddd-ddddd-ddddd where d = decimal digit.
INT acquisitionState	1.3.6.1.4.1.1166.1.621.11.1	INTEGER	read-only	The acquisition state for the active signal
INT activePort	1.3.6.1.4.1.1166.1.621.2.2.1	INTEGER	read-write	The RF port that is active during a manual tune.
INT alarmConditionLED	1.3.6.1.4.1.1166.1.621.12.3	INTEGER	read-only	The Alarm condition LED is on (illuminated) when the IRD is in alarm state
INT alarmLEDBlinkStatus	1.3.6.1.4.1.1166.1.621.16.4.2.1	INTEGER	read-only	0 - LED is not blinking(OFF/ON) 1 - LED is blinking
alarmLedStatus	1.3.6.1.4.1.1166.1.621.16.4.2
alarms	1.3.6.1.4.1.1166.1.621.8.1
INT alarmTest	1.3.6.1.4.1.1166.1.621.8.1.3	INTEGER	read-write	A manual test of the alarm indicators. Setting ON places the unit in the alarm condition.
INT alarmTrigger	1.3.6.1.4.1.1166.1.621.8.1.2	INTEGER	read-write	The trigger condition for which the alarm is activated. When the alarm is activated the Alarm LED illuminates and the alrm relay indicates an alarm condition. The alarm is activated for any of the following conditions 1. The tuner loses lock when the input is RF 2. The unit is not authorized to access the selected service 3. The unit loses video When Auto is selected the alarm activates for any of these conditions and when Disabled is selected the alarm does not activate for any condition.
INT asiEnable	1.3.6.1.4.1.1166.1.621.5.1.3	INTEGER	read-write	Option to enable or disbale the ASI output. Note that lock-off is a read only value used by the uplink to lock asiEnable. It cannot be set via SNMP. Also, when this value is lock-off, this entire field is read only.
INT aspectRatioInput	1.3.6.1.4.1.1166.1.621.1.3	INTEGER	read-only	The aspect ratio of the video that is carried in the broadcast signal.
INT aspectRatioOutput	1.3.6.1.4.1.1166.1.621.1.4	INTEGER	read-write	The aspect ratio of the output video signal.
audio	1.3.6.1.4.1.1166.1.621.16.1
INT audio1Compression	1.3.6.1.4.1.1166.1.621.6.1.1.6	INTEGER	read-write	The degree of audio level compression.
audio1Config	1.3.6.1.4.1.1166.1.621.6.1.1
INT audio1DiagNorm	1.3.6.1.4.1.1166.1.621.6.1.1.4	INTEGER	read-write	This varaiables enables and diables the audio dialog normalization
INT audio1DownMix	1.3.6.1.4.1.1166.1.621.6.1.1.5	INTEGER	read-write	The mode of the audio output. The unit downmixes the input audio to the selected channel mode.
INT audio1GainControl	1.3.6.1.4.1.1166.1.621.6.1.1.1	INTEGER	read-only	In audio gain control joint, only the left audio channel is edited. The right audio channel gain will be set to the left.
INT audio1LeftGain	1.3.6.1.4.1.1166.1.621.6.1.1.2	INTEGER	read-write	The left audio signal output level from -20 dB to 0 dB, in 1 dB increments.
OCT audio1LeftLanguage	1.3.6.1.4.1.1166.1.621.6.2.1.1	OCTET STRING	read-write	The language for the audio1 . This 5-character language string is formatted as three letters followed by two numbers. The 2-digit number represents the order of the 3-letter language in the service, e.g., eng01 denotes the second English component that is carried in the active service. The unit processes the default language when the preferred language setting is def (In this case the string is only 3 character wide). Note that the language string is converted to lower case automatically when this configuration is to be applied
OCT audio1LeftLanguageStatus	1.3.6.1.4.1.1166.1.621.6.2.1.3	OCTET STRING	read-only	The language of the left audio channel being presented by the IRD. This is a 3(def) or 5(e.g., eng01) character string of the similar format as of the audio1LeftLanguage.
audio1Output	1.3.6.1.4.1.1166.1.621.6.2.1
INT audio1RightGain	1.3.6.1.4.1.1166.1.621.6.1.1.3	INTEGER	read-only	The right audio signal output level from -20 dB to 0 dB, in 1 dB increments.
OCT audio1RightLanguage	1.3.6.1.4.1.1166.1.621.6.2.1.2	OCTET STRING	read-write	The language for the right audio channel when the AudioDownMix selection is dualMono. When the AudioDownMix is not dualMono the value mirrors the audio1LeftLanguage and any changes to this value does not have any effect. This is a 3(def) or 5(e.g., eng01) character string similar to the left language string. Note that the language string is converted to lower case automatically when this configuration is to be applied
OCT audio1RightLanguageStatus	1.3.6.1.4.1.1166.1.621.6.2.1.4	OCTET STRING	read-only	The language of the right audio channel being presented by the IRD. This is a 3(def) or 5(e.g., eng01) character string of the similar format as of the audio1LeftLanguage. Note that the language string is converted to lower case automatically when this configuration is to be applied
INT audio1TestPattern	1.3.6.1.4.1.1166.1.621.10.2.2	INTEGER	read-write	The audio test signal that is outputted by the unit for audio 1. The following options are available: o 1000 Hz @ +16 dBm (for mono) o 4040, 3960 Hz @ + 4dBm each (for left and right) o OFF
INT audio2Compression	1.3.6.1.4.1.1166.1.621.6.1.2.6	INTEGER	read-write	The degree of audio level compression.
audio2Config	1.3.6.1.4.1.1166.1.621.6.1.2
INT audio2DiagNorm	1.3.6.1.4.1.1166.1.621.6.1.2.4	INTEGER	read-write	This varaiables enables and diables the audio dialog normalization
INT audio2DownMix	1.3.6.1.4.1.1166.1.621.6.1.2.5	INTEGER	read-write	The mode of the audio output. The unit downmixes the input audio to the selected channel mode .
INT audio2GainControl	1.3.6.1.4.1.1166.1.621.6.1.2.1	INTEGER	read-only	In audio gain control joint, only the left audio channel is edited. The right audio channel gain will be set to the left.
INT audio2LeftGain	1.3.6.1.4.1.1166.1.621.6.1.2.2	INTEGER	read-write	The left audio signal output level from -20 dB to 0 dB, in 1 dB increments.
OCT audio2LeftLanguage	1.3.6.1.4.1.1166.1.621.6.2.2.1	OCTET STRING	read-write	The language for the audio1 . This 5-character language string is formatted as three letters followed by two numbers. The 2-digit number represents the order of the 3-letter language in the service, e.g., eng01 denotes the second English component that is carried in the active service. The unit processes the default language when the preferred language setting is def(in this case. string is 3 letters wide). Note that the language string is converted to lower case automatically when this configuration is to be applied
OCT audio2LeftLanguageStatus	1.3.6.1.4.1.1166.1.621.6.2.2.3	OCTET STRING	read-only	The language of the left audio channel being presented by the IRD. This is a 3(def) or 5(e.g., eng01) character string of the similar format as of the audio2LeftLanguage. Note that the language string is converted to lower case automatically when this configuration is to be applied
audio2Output	1.3.6.1.4.1.1166.1.621.6.2.2
INT audio2RightGain	1.3.6.1.4.1.1166.1.621.6.1.2.3	INTEGER	read-only	The right audio signal output level from -20 dB to 0 dB, in 1 dB increments.
OCT audio2RightLanguage	1.3.6.1.4.1.1166.1.621.6.2.2.2	OCTET STRING	read-write	The language for the right audio channel when the AudioDownMix selection is dualMono. When the AudioDownMix is not dualMono the value mirrors the audio2LeftLanguage and any changes to this value does not have any effect. This is a 3(def) or 5(e.g., eng01) character string of the similar format as of the audio2LeftLanguage. Note that the language string is converted to lower case automatically when this configuration is to be applied
OCT audio2RightLanguageStatus	1.3.6.1.4.1.1166.1.621.6.2.2.4	OCTET STRING	read-only	The language of the right audio channel being presented by the IRD. This is a 3(def) or 5(e.g., eng01) character string of the similar format as of the audio2LeftLanguage. Note that the language string is converted to lower case automatically when this configuration is to be applied
INT audio2TestPattern	1.3.6.1.4.1.1166.1.621.10.2.3	INTEGER	read-write	See the DESCRIPTION for the audio1TestPattern object.
audioConfig	1.3.6.1.4.1.1166.1.621.6.1
audioMib	1.3.6.1.4.1.1166.1.621.6
audioOutput	1.3.6.1.4.1.1166.1.621.6.2
INT authorizationState	1.3.6.1.4.1.1166.1.621.11.2	INTEGER	read-only	The authorization state for viewing the current signal. This object mirrors the 'Auth State' field in the Fast Facts 1 OSD.
INT authorizedLED	1.3.6.1.4.1.1166.1.621.12.2	INTEGER	read-only	The Authorized LED is on (illuminated) when the Signal LED is on and either (1) the programmer has transmitted the access messages to allow the unit to decrypt the signal or (2) the signal has been transmitted in an unencrypted of fixed encrypted mode. This object mirrors the LED on the front panel
INT ber	1.3.6.1.4.1.1166.1.621.16.6.2	INTEGER	read-only	This displays Bit Errors.
OCT bootVersion	1.3.6.1.4.1.1166.1.621.9.2.1	OCTET STRING	read-only	The version of the boot code.
INT caMsgCount	1.3.6.1.4.1.1166.1.621.16.5.2	INTEGER	read-only	Gives CA Message Count
channelMib	1.3.6.1.4.1.1166.1.621.3
INT channelNum	1.3.6.1.4.1.1166.1.621.11.6	INTEGER	read-only	The virtual channel number of the current signal. This object mirrors the 'VC #' field in the Fast Facts 1 OSD.
INT channelNumber	1.3.6.1.4.1.1166.1.621.3.1.2	INTEGER	read-write	The virtual channel.
channelSelect	1.3.6.1.4.1.1166.1.621.3.1
channelStatus	1.3.6.1.4.1.1166.1.621.3.2
INT clearCounters	1.3.6.1.4.1.1166.1.621.10.1.2	INTEGER	read-write	Clears the counters in the on-screen diagnostics to zero.
INT clearlostlockcount	1.3.6.1.4.1.1166.1.621.16.6.7	INTEGER	read-write	Clears the lostlockcount counter to zero.
INT clearrserror	1.3.6.1.4.1.1166.1.621.16.6.6	INTEGER	read-write	Clears the rserror counter to zero.
codeDownload	1.3.6.1.4.1.1166.1.621.16.3
INT codeDownloadBit	1.3.6.1.4.1.1166.1.621.16.3.1	INTEGER	read-only	Monitor the Code Download process 0 - off 1 - on
INT coMsgCount	1.3.6.1.4.1.1166.1.621.16.5.8	INTEGER	read-only	Gives Channel Override Message Count
INT contrast	1.3.6.1.4.1.1166.1.621.5.1.1	INTEGER	read-write	The LCD contrast, with 0 representing the least contrast and 30 representing the most.
INT cueToneSignal	1.3.6.1.4.1.1166.1.621.10.2.4	INTEGER	read-write	The cue tone test signal.The unit generates a cue test tone sequence consisting of 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, *, #, A, B, C, D. The unit repeats the cue test tone sequence when enabled. The unit generates a cue tone test tone sequence with a 50 msec tone and inter-tone duration, a 2 second interval between sequences, and immediate activation. When the users set it to On via SNMP. Cuetones are played continuously.
dataMib	1.3.6.1.4.1.1166.1.621.7
dataStatus	1.3.6.1.4.1.1166.1.621.7.1
IP defaultGateway	1.3.6.1.4.1.1166.1.621.7.3.3	IpAddress	read-only	The IP address of the gateway that is used by the snmp port 1, in the dotted-decimal format.
diagnosticMib	1.3.6.1.4.1.1166.1.621.10
INT diagnosticScreen	1.3.6.1.4.1.1166.1.621.10.1.1	INTEGER	read-write	The diagnostic screen that is to be presented by the unit on the video output.
dod	1.3.6
INT downloadLED	1.3.6.1.4.1.1166.1.621.12.8	INTEGER	read-only	The Download LED is on ( illuminated ) when an active download is in progress
dsr	1.3.6.1.4.1.1166.1.621			The managed objects for the dsr mib.
INT dvbCodeRate	1.3.6.1.4.1.1166.1.621.2.2.6	INTEGER	read-write	The code rate of the channel being tuned to. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.
INT dvbS2codeRate	1.3.6.1.4.1.1166.1.621.2.2.13	INTEGER	read-write	The code rate of the channel being tuned to. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.
INT dvbS2symbolRate	1.3.6.1.4.1.1166.1.621.2.2.12	INTEGER	read-write	The symbol-rate to be tuned to in units of sps. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.
INT dvbSymbolRate	1.3.6.1.4.1.1166.1.621.2.2.5	INTEGER	read-write	The symbol-rate to be tuned to in units of sps. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.
INT dwnldMsgCount	1.3.6.1.4.1.1166.1.621.16.5.10	INTEGER	read-only	Gives Download Message Count
INT dwnldPreMsgCount	1.3.6.1.4.1.1166.1.621.16.5.9	INTEGER	read-only	Gives Download preamble message Count
INT ebNo	1.3.6.1.4.1.1166.1.621.16.6.3	INTEGER	read-only	This displays the Eb/No measured in the IRD.
INT emmMsgCount	1.3.6.1.4.1.1166.1.621.16.5.11	INTEGER	read-only	Gives EMM Message Count
INT encryptionMode	1.3.6.1.4.1.1166.1.621.11.3	INTEGER	read-only	The encryption mode of the current signal. This object mirrors the 'Encryption' field in the Fast Facts 1 OSD.
enterprises	1.3.6.1.4.1
ethernet10_100	1.3.6.1.4.1.1166.1.621.7.3
ethernetGigE	1.3.6.1.4.1.1166.1.621.7.4
INT ethernetIP	1.3.6.1.4.1.1166.1.621.7.1.1	INTEGER	read-only	Retrieves whether the select channel contains IP data, as defined in the downloaded network data from the uplink.
INT evenBlkoutMsgCount	1.3.6.1.4.1.1166.1.621.16.5.15	INTEGER	read-only	Gives Event Blckout Message message Count
extHardwareMib	1.3.6.1.4.1.1166.1.621.8
falseLock	1.3.6.1.4.1.1166.1.621.16.4.1
INT falseLockStatus	1.3.6.1.4.1.1166.1.621.16.4.1.1	INTEGER	read-only	Checks for false lock
INT fecRate	1.3.6.1.4.1.1166.1.621.11.12	INTEGER	read-only	The FEC rate of the current signal. This object mirrors the 'FEC Rate' field in the Fast Facts 1 OSD.
INT field	1.3.6.1.4.1.1166.1.621.10.3.2	INTEGER	read-write	The field on which the VITS test pattern is presented by the unit on the video output. 'n/a' is a read-only value that the unit returns when the waveform object is set to 'transmitted' or 'disabled'.
INT fingerPrintMessageCount	1.3.6.1.4.1.1166.1.621.16.5.12	INTEGER	read-only	Gives Finger Print message Count
firmware	1.3.6.1.4.1.1166.1.621.9.2
OCT firmwareVersion	1.3.6.1.4.1.1166.1.621.9.2.3	OCTET STRING	read-only	The version of firmware code.
INT formatRate	1.3.6.1.4.1.1166.1.621.5.1.8	INTEGER	read-write	Format and rate of the ASI output
OCT fpgaVersion	1.3.6.1.4.1.1166.1.621.9.2.2	OCTET STRING	read-only	The version of the fpga.
INT freq	1.3.6.1.4.1.1166.1.621.11.13	INTEGER	read-only	The frequency of the L-band signal, in kHz, that is applied to the antenna connector on the unit's back panel. This object mirrors the 'Frequency' field in the Fast Facts 1 OSD.
INT frequency	1.3.6.1.4.1.1166.1.621.2.2.4	INTEGER	read-write	The L-band frequency, in MHz, during a manual tune. A new manual tune is initiated when this object is set.This value is valid only of the Frequency Plan selection is lfreq. Value -1 indicates its Not applicable.
INT frequencyOffset	1.3.6.1.4.1.1166.1.621.16.6.1	INTEGER	read-only	The acquired offset of the L-band frequency in MHz.
IP gigEgateway	1.3.6.1.4.1.1166.1.621.7.4.3	IpAddress	read-write	The IP address of the gateway that is used by the gigE port, in the dotted-decimal format.
IP gigEipAddress	1.3.6.1.4.1.1166.1.621.7.4.1	IpAddress	read-write	The IP address of the gigE port, in the common dotted-decimal format.
OCT gigEmacAddr	1.3.6.1.4.1.1166.1.621.7.4.4	OCTET STRING	read-only	The gigEthernet MAC address in hh:hh:hh:hh:hh:hh format.
INT gigEmode	1.3.6.1.4.1.1166.1.621.7.4.5	INTEGER	read-write	The gigEthernet mode is one of the following values MPTS,disabled,TS-DSMCC or DSM-CC.
IP gigEsubnetMask	1.3.6.1.4.1.1166.1.621.7.4.2	IpAddress	read-write	The subnet mask of the gigE port, in the dotted-decimal format.
giMIB	1.3.6.1.4.1.1166
giproducts	1.3.6.1.4.1.1166.1
INT hcmMsgCount	1.3.6.1.4.1.1166.1.621.16.5.13	INTEGER	read-only	Gives hardware control Message Count
identificationGroup	1.3.6.1.4.1.1166.1.621.14
STR identMIBVersion	1.3.6.1.4.1.1166.1.621.14.1	DisplayString	read-only	The version number of this MIB.
STR identUnitModel	1.3.6.1.4.1.1166.1.621.14.2	DisplayString	read-only	The unit model of this IRD.
internet	1.3.6.1
IP ipAddress	1.3.6.1.4.1.1166.1.621.7.3.1	IpAddress	read-only	The IP address of the snmp port 1, in the common dotted-decimal format.
irdStatus	1.3.6.1.4.1.1166.1.621.16.4
ledStatus	1.3.6.1.4.1.1166.1.621.12
INT line	1.3.6.1.4.1.1166.1.621.10.3.3	INTEGER	read-write	The line into which the VITS test pattern is presented by the unit on the video output. 'n/a' is a read-only value that the unit returns when the waveform object is set to 'transmitted' or 'disabled'.
INT lnbPower	1.3.6.1.4.1.1166.1.621.5.1.6	INTEGER	read-write	Option to enable or disable LNB Power.
INT lostlockcount	1.3.6.1.4.1.1166.1.621.16.6.5	INTEGER	read-only	This displays the number of times tuner lost lock.
OCT macAddr	1.3.6.1.4.1.1166.1.621.7.3.4	OCTET STRING	read-only	The ethernet 1 MAC address in hh:hh:hh:hh:hh:hh format.
manualTune	1.3.6.1.4.1.1166.1.621.2.2
messages	1.3.6.1.4.1.1166.1.621.16.5
INT mode	1.3.6.1.4.1.1166.1.621.2.2.2	INTEGER	read-write	The frequency plan of the satellite to which the unit tunes during installation. The unit accepts a C-Band satellite transponder number when the selection is xpndr. The unit accepts a discrete frequency value when the selection is lfreq
INT modulationMode	1.3.6.1.4.1.1166.1.621.2.2.9	INTEGER	read-write	The modulation mode to be used for the manual tune. A new manual tune is initiated when this object is set.
INT mpegServiceNumber	1.3.6.1.4.1.1166.1.621.4.1	INTEGER	read-write	The MPEG service number which the IRD has to play.
IP mptsIpAddr	1.3.6.1.4.1.1166.1.621.7.4.6	IpAddress	read-write	The MPTS IP address of the gigE port in the dotted-decimal format.
INT mptsPort	1.3.6.1.4.1.1166.1.621.7.4.7	INTEGER	read-write	The port associated with the MPTS IP address.
INT muxStatus	1.3.6.1.4.1.1166.1.621.11.17	INTEGER	read-only	The multiplex format of the active L-Band signal
INT networkTextMsgCount	1.3.6.1.4.1.1166.1.621.16.5.5	INTEGER	read-only	Gives Network text Message Count
INT niMsgCount	1.3.6.1.4.1.1166.1.621.16.5.4	INTEGER	read-only	Gives Network Information Message Count
org	1.3
INT patMsgCount	1.3.6.1.4.1.1166.1.621.16.5.1	INTEGER	read-only	Gives PAT Message Count
INT pmtMsgCount	1.3.6.1.4.1.1166.1.621.16.5.3	INTEGER	read-only	Gives PMT message Count
INT polarization	1.3.6.1.4.1.1166.1.621.11.16	INTEGER	read-only	The polarization, as indicated in the virtual channel map, for the current signal. This object mirrors the 'Polarization' field in the Fast Facts 1 OSD.
port1	1.3.6.1.4.1.1166.1.621.2.1.1
INT port1Polarity	1.3.6.1.4.1.1166.1.621.2.1.1.3	INTEGER	read-write	The polarity of the RF input applied to the RF port. The undefined value is not writeable; instead, undefined can only be set by the uplink.
OCT port1Satellite	1.3.6.1.4.1.1166.1.621.2.1.1.2	OCTET STRING	read-write	A 2 to 3 character abbreviation of the name of the satellite to which the RF port is associated.
INT port1SetupMode	1.3.6.1.4.1.1166.1.621.2.1.1.1	INTEGER	read-write	When the setup mode is set to manual the satellite name and polarity has to befined by the user. When the port mode is set to auto the Satellite name and polarity will be automatically set during the first channel change.
port2	1.3.6.1.4.1.1166.1.621.2.1.2
INT port2Polarity	1.3.6.1.4.1.1166.1.621.2.1.2.3	INTEGER	read-write	The polarity of the RF input applied to the RF port. The undefined value is not writeable; instead, undefined can only be set by the uplink.
OCT port2Satellite	1.3.6.1.4.1.1166.1.621.2.1.2.2	OCTET STRING	read-write	A 2 to 3 character abbreviation of the name of the satellite to which the RF port is associated.
INT port2SetupMode	1.3.6.1.4.1.1166.1.621.2.1.2.1	INTEGER	read-write	When the setup mode is set to manual the satellite name and polarity has to befined by the user. When the port mode is set to auto the Satellite name and polarity will be automatically set during the first channel change.
INT primaryAudioLock	1.3.6.1.4.1.1166.1.621.16.1.1	INTEGER	read-only	Gives Primary Audio is locked or not
INT primaryAudioPID	1.3.6.1.4.1.1166.1.621.16.1.4	INTEGER	read-only	Gives Primary Audio PID
private	1.3.6.1.4
INT psk8CodeRate	1.3.6.1.4.1.1166.1.621.2.2.11	INTEGER	read-write	The code rate of the channel being tuned to. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.
INT psk8SymbolRate	1.3.6.1.4.1.1166.1.621.2.2.10	INTEGER	read-write	The symbol-rate to be tuned to in units of sps. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.
INT resetIRD	1.3.6.1.4.1.1166.1.621.5.1.7	INTEGER	read-write	Option to reboot the box.
INT retuneMonitorEnable	1.3.6.1.4.1.1166.1.621.13.1	INTEGER	read-write	Enables retune monitoring by the IRD. When read, this leaf provides the actual enable/disable status of the retune monitoring function in the IRD, and not just the last value that was written to this leaf. The IRD resets retuneMsgStatistic and all entries in the retuneMsgTable each time it receives an enable message; toggling enable/disable/enable is not required for this reset.
retuneMonitorMIB	1.3.6.1.4.1.1166.1.621.13
OCT retuneMsgActivationTime	1.3.6.1.4.1.1166.1.621.13.6	OCTET STRING	read-only	The activation time of the most recent active retune message. The activation time is a 32-bit count of GPS seconds since January 6, 1980, representing the time at which the retune is scheduled to occur. Past activation times are interpreted as immediate activation.
INT retuneMsgCnt	1.3.6.1.4.1.1166.1.621.13.8	INTEGER	read-only	The total number of instances that the IRD has received for the most recent active retune message. Range = 0 - 0xFFFF. Note: this counter is incremented when a retune message is received for which the CRC of that retune message matches the CRC of the current retune message (i.e., the value of retuneMsgCRC).
OCT retuneMsgCRC	1.3.6.1.4.1.1166.1.621.13.7	OCTET STRING	read-only	The 4-byte CRC value of the most recent active retune message.
INT retuneMsgStatistic	1.3.6.1.4.1.1166.1.621.13.2	INTEGER	read-only	The total number of new retune messages. This counter is incremented whenever the IRD detects a new retune message, but is not incremented by each instance (duplicate) of a retune message. This counter provides a useful troubleshooting tool for determining whether the IRD is detecting any retune messages. Range = 0x0000 - 0xFFFF. Note: This counter is not incremented for every possible retune message. This counter is only incremented when a retune becomes active. The IRD ignores retune messages in which the activation time is still in the future. The IRD also ignores any retune message if the activation time is further in the past than the current retune for the same virtual network.
INT retuneMsgVCTid	1.3.6.1.4.1.1166.1.621.13.4	INTEGER	read-only	The target virtual channel map ID of the most recent active retune message. Range = 0 - 0xFFFF.
INT retuneMsgVirtChannel	1.3.6.1.4.1.1166.1.621.13.5	INTEGER	read-only	The target virtual channel of the most recent active retune message. Range = 0 - 4095.
INT retuneMsgVirtNetworkIDindex	1.3.6.1.4.1.1166.1.621.13.3	INTEGER	read-write	A table of retune messages is indexed by this target virtual network ID. This table does not have entries for each instance (duplicate) of a retune message that the IRD receives because the uplink repeatedly broadcasts instances of each retune message for the duration of the virtual network program. Instead, this table presents select metrics describing the retune message, as described below. Each table entry pertains to the most recent active retune message. A retune message is considered active when the activation time is in the past. The IRD replaces the current retuneMsgEntry when a new retune message is received having an activation time that is in the past but nearer to the present time than is the activation time of the current retuneMsgEntry. The IRD ignores retune messages in which the activation time is in the future. The virtual network ID indicates which retune message is targeted. This leaf serves as the index for the table. Make sure this index is set prior to accessing the following retune message parameters. Range = 1 - 256.
rf	1.3.6.1.4.1.1166.1.621.16.6
rfPortsMib	1.3.6.1.4.1.1166.1.621.2
rfPortsSetup	1.3.6.1.4.1.1166.1.621.2.1
INT rserror	1.3.6.1.4.1.1166.1.621.16.6.4	INTEGER	read-only	This displays the Reed Solomon Errors.
OCT satelliteName	1.3.6.1.4.1.1166.1.621.11.14	OCTET STRING	read-only	A 2 to 4 character satellite reference name, as indicated in the virtual channel map, for the current signal. This object mirrors the 'Sat' field in the Fast Facts 1 OSD.
OCT satelliteStatus	1.3.6.1.4.1.1166.1.621.3.2.3	OCTET STRING	read-only	The name of the current satellite as received from the uplink. A Blank string is returned if the name is not available .
screenDisplay	1.3.6.1.4.1.1166.1.621.10.1
INT secondaryAudioLock	1.3.6.1.4.1.1166.1.621.16.1.2	INTEGER	read-only	Gives Secondary Audio is locked or not
INT secondaryAudioPID	1.3.6.1.4.1.1166.1.621.16.1.5	INTEGER	read-only	Gives Secondary Audio PID
INT serviceNumber	1.3.6.1.4.1.1166.1.621.11.7	INTEGER	read-only	The MPEG-2 service number, as indicated in the virtual channel map, for the current signal. This object mirrors the 'Service #' field in the Fast Facts 1 OSD.
serviceSelectionMib	1.3.6.1.4.1.1166.1.621.4
INT signalLED	1.3.6.1.4.1.1166.1.621.12.1	INTEGER	read-only	The Signal LED is on (illuminated) when the unit recognizes the signal as a DigiCipher II signal. This object mirrors the LED on the front panel
INT signalPower	1.3.6.1.4.1.1166.1.621.11.9	INTEGER	read-only	The RF power level of the current signal, and measured in units of 0.1 dBm. For example, '-650' represents -65.0 dBm.
INT signalQuality	1.3.6.1.4.1.1166.1.621.11.8	INTEGER	read-only	The RF quality level of the current signal. This object mirrors the 'Signal Quality' field in the Fast Facts 1 OSD.
signalStatus	1.3.6.1.4.1.1166.1.621.11
INT snr	1.3.6.1.4.1.1166.1.621.16.6.8	INTEGER	read-only	This displays the SNR value.
OCT source	1.3.6.1.4.1.1166.1.621.3.2.2	OCTET STRING	read-only	The name of the current source signal as received from the uplink.A Blank string is returned if the name is not available .
statusMib	1.3.6.1.4.1.1166.1.621.9
IP subnetMask	1.3.6.1.4.1.1166.1.621.7.3.2	IpAddress	read-only	The subnet mask of the snmp port 1, in the dotted-decimal format.
INT subtitleDisplay	1.3.6.1.4.1.1166.1.621.7.2.3	INTEGER	read-write	The subtitle language currently being presented by the IRD
OCT subtitleLanguage	1.3.6.1.4.1.1166.1.621.7.2.1	OCTET STRING	read-write	The selected subtitle track. Applicable when the selected channel carries multiple subtitle tracks. The 5-character string has the following representation: sssdd where sss = 3-char ISO 639 code for the subtitle language dd = 2-digits indicating the occurrence of the specified language 'ENG02' would select, for example, the subtitle track for the second occurrence of English subtitles. To turn the subtitle off, enter 'Off01' or 'Off00' at the browser. The user must enter the ordinal.
OCT subtitleLanguageStatus	1.3.6.1.4.1.1166.1.621.7.2.2	OCTET STRING	read-only	The subtitle language currently being presented by the IRD
INT subtitleMsgCount	1.3.6.1.4.1.1166.1.621.16.5.7	INTEGER	read-only	Gives Subtitle Message Count
INT symbolCodeBit	1.3.6.1.4.1.1166.1.621.2.2.8	INTEGER	read-write	The symbol, code rate, and bitstream select combination during a manual tune. A new manual tune is initiated when this object is set. The symbol rate takes eight possible values: 29.3, 19.5, 14.6, 11.7, 9.76, 7.32, 4.88, and 3.25 Msps. The code rate also takes eight possible values: 7/8, 5/6, 4/5, 3/4, 2/3, 3/5, 1/2, and 5/11. The bitstream select takes two possible values: combined and split. Value -1 indicates its Not applicable.
INT symbolRate	1.3.6.1.4.1.1166.1.621.11.11	INTEGER	read-only	The symbol rate of the current signal. This object mirrors the 'Symbol Rate' field in the Fast Facts 1 OSD.
testMib	1.3.6.1.4.1.1166.1.621.16
testSignals	1.3.6.1.4.1.1166.1.621.10.2
textSetup	1.3.6.1.4.1.1166.1.621.7.2
OCT transponder	1.3.6.1.4.1.1166.1.621.3.2.1	OCTET STRING	read-only	The current transponder name (alpha/numeric) as received from the uplink.A Blank string is returned if the name is not available .
INT transponderNumber	1.3.6.1.4.1.1166.1.621.2.2.3	INTEGER	read-write	The transponder number to which the unit tunes during installation This in turn specifies the L-Band frequency to which the unit tunes during installation. This value is valid only when the FrequencyPlan selection is xpndr. Value -1 indicates its Not applicable.
OCT tvPasscard	1.3.6.1.4.1.1166.1.621.9.1.2	OCTET STRING	read-only	The electronic address of the TV Pass Card, if present, in the unit address format. When no TV Pass Card is present the value returned is 'Not inserted'.
INT uimMsgCount	1.3.6.1.4.1.1166.1.621.16.5.14	INTEGER	read-only	Gives Unit information message Count
OCT unitAddr	1.3.6.1.4.1.1166.1.621.11.4	OCTET STRING	read-only	The unit's electronic address in the following format: ddd-ddddd-ddddd-ddd where d = decimal digit. This object mirrors the 'Unit' field in the Fast Facts 1 OSD.
OCT unitAddress	1.3.6.1.4.1.1166.1.621.9.1.1	OCTET STRING	read-only	The unit's electronic address in the following format: ddd-ddddd-ddddd-ddd where d = decimal digit.
unitControl	1.3.6.1.4.1.1166.1.621.5.1
unitControlMib	1.3.6.1.4.1.1166.1.621.5
OCT upgradeFirmwareVersion	1.3.6.1.4.1.1166.1.621.9.2.4	OCTET STRING	read-only	The upgrade version of firmware code.
INT vctID	1.3.6.1.4.1.1166.1.621.3.1.1	INTEGER	read-write	The virtual channel table number.
INT vctIDFast	1.3.6.1.4.1.1166.1.621.11.5	INTEGER	read-only	The current virtual channel table number. This object mirrors the 'VCT ID' field in the Fast Facts 1 OSD.
video	1.3.6.1.4.1.1166.1.621.16.2
INT videoLock	1.3.6.1.4.1.1166.1.621.16.2.1	INTEGER	read-only	Gives Video is locked or not
videoMib	1.3.6.1.4.1.1166.1.621.1
INT videoOutput525Lines	1.3.6.1.4.1.1166.1.621.1.1	INTEGER	read-write	The format of the output video that the unit renders when the unit is tuned to a 525 line video broadcast signal.
INT videoOutput625Lines	1.3.6.1.4.1.1166.1.621.1.2	INTEGER	read-write	The format of the output video that the unit renders when the unit is tuned to a 625 line video broadcast signal.
INT videoPID	1.3.6.1.4.1.1166.1.621.16.2.2	INTEGER	read-only	Gives video PID
INT videoTestPattern	1.3.6.1.4.1.1166.1.621.10.2.1	INTEGER	read-write	The full-field video test pattern that is presented by the unit on the video output.
INT virtualChannelMsgCount	1.3.6.1.4.1.1166.1.621.16.5.6	INTEGER	read-only	Gives Virtual channel message Count
vits	1.3.6.1.4.1.1166.1.621.10.3
INT waveform	1.3.6.1.4.1.1166.1.621.10.3.1	INTEGER	read-write	The VITS test pattern that is presented by the unit on the the video output.
INT xpndrNumber	1.3.6.1.4.1.1166.1.621.11.15	INTEGER	read-only	The transponder number of the satellite, as indicated in the virtual channel map, for the current signal. A value of zero indicates the first transponder, and so on. This object mirrors the '/Xpndr' field in the Fast Facts 1 OSD.

RFC description

ARRIS DSR4410MD commercial digital video receiver management and DVB-S2 configuration.

Start monitoring ARRIS DSR4410MD satellite Integrated Receiver-Decoder (IRD) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DSR4410MD-MIB

What Is DSR4410MD-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description