DPS-MIB-NGD-V10-V2

MIB Reference — IPNetwork Monitor · Updated October 05, 2026

All MIBs › DPS-MIB-NGD-V10-V2

Organization: DPS Telecom

Last Updated: 2012-08-08

Category: Domain: Telco/Transport, Vendor: DPS Telecom

Description: Provides SNMPv2 management objects for DPS Telecom NetGuardian D-series remote telemetry units.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DPS-MIB-NGD-V10-V2?

DPS-MIB-NGD-V10-V2 is a vendor-specific SNMPv2 MIB for DPS Telecom's NetGuardian D-series remote telemetry units (RTUs), devices used in remote site monitoring for telecom and utility infrastructure. It exposes management objects covering the RTU's discrete/analog input status, alarm points, and general device configuration used to monitor remote unmanned sites. Its core purpose is environmental and equipment health monitoring: NetGuardian RTUs typically report site conditions such as temperature, power supply/battery status, door/intrusion alarms, and generic contact-closure alarm inputs that reflect the operational status of co-located equipment (e.g., a generator, HVAC unit, or power plant). As a second-generation, vendor-specific MIB it stands independent of IETF standards, relying on DPS Telecom's own enterprise OID branch and RTU firmware for object semantics. It is typically deployed at remote telecom huts, cell sites, or utility substations to give NOC staff SNMP-based visibility into unmanned facility conditions, and technicians can download the DPS-MIB-NGD-V10-V2 file to load into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DPS-MIB-NGD-V10-V2. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

  • DPS Telecom NetGuardian D-series remote telemetry unit (RTU)

Monitoring Examples

An admin would poll the RTU's alarm/discrete-input status objects to check whether a site door has been opened or a generator has switched to backup power, since these register as active alarm points on the NetGuardian. Analog input objects reporting site temperature or battery voltage would reveal HVAC failure or battery drain before it causes an outage. Because no specific object names were available in the source data, table/object names here are inferred from the typical NetGuardian RTU MIB structure (alarm point tables, analog channel tables).

What Can Be Monitored

  • discrete alarm input status
  • analog sensor readings (e.g., temperature, voltage)
  • site power/battery status
  • door/intrusion alarm state
  • device configuration status
Imported Objects

From DPS-MIB-V38

dpsAlarmControlOBJECT-IDENTITY

From DPS-MIB-V38-V2

dpsRTUv2OBJECT-IDENTITY
dpsRTUv2ADisplayOBJECT-TYPE
dpsRTUv2APntDescOBJECT-TYPE
dpsRTUv2APointOBJECT-TYPE
dpsRTUv2APortOBJECT-TYPE
dpsRTUv2AStateOBJECT-TYPE
dpsRTUv2CAddressOBJECT-TYPE
dpsRTUv2DateTimeOBJECT-TYPE

From SNMPv2-MIB

sysDescrOBJECT-TYPE
sysLocationOBJECT-TYPE

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OIDs

RFC description

Manages DPS NetGuardian 4.0 series RTU equipment and notifications.

Start monitoring DPS Telecom remote telemetry units (RTUs) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DPS-MIB-NGD-V10-V2