DKSF-707-2-X-X-1

All MIBs › DKSF-707-2-X-X-1

Organization: Alentis Electronics

Last Updated: 2015-02-09

Category: Domain: Environmental Monitoring, Vendor: NetPing/DKSF

Description: MIB for DKSF-707 NetPing device firmware 2.x providing enhanced environmental sensor and relay management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DKSF-707-2-X-X-1?

This MIB is a NetPing vendor module for the DKSF-707 device running firmware 2.x, which in this variant acts as an SMS/GSM bridge rather than a purely environmental sensor unit. It exposes configuration and status data for a cellular modem subsystem, including GSM network registration, signal strength, and SMS send/receive functions, plus device reboot controls and trap notification settings. For monitoring hardware/software status, it is notably used to check GSM modem health (npGsmFailed, npGsmRegistration, npGsmStrength) and to trigger or observe soft/hard reboots (npSoftReboot, npForcedReboot, npResetStack) of the unit. It depends on the same NetPing/lightcom private enterprise tree as related NetPing MIBs rather than any IETF standard. Typical deployment is in remote or unattended sites where SMS-based alerting or out-of-band notification is needed alongside basic environmental/relay monitoring, such as remote telecom huts or utility cabinets. Engineers can download the DKSF-707-2-X-X-1 file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DKSF-707-2-X-X-1. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

NetPing DKSF-707 GSM/SMS bridge device

Monitoring Examples

An operator would poll npGsmRegistration and npGsmStrength to confirm the embedded GSM modem is registered on the cellular network with adequate signal, and check npGsmFailed to detect modem faults. npGsmUnparsedRxSms and npGsmUnparsedRxSmsFrom expose incoming SMS messages the device could not parse as commands, useful for diagnosing misconfigured remote-control SMS syntax. If the device becomes unresponsive, an admin can invoke npForcedReboot or npResetStack remotely to recover it without a site visit, and npTrapInfo/npTrapEmailTo define where alert notifications about these events are routed.

What Can Be Monitored

GSM network registration status
GSM signal strength
GSM modem failure state
unparsed incoming SMS messages and sender
device reboot/reset status
trap email notification target

Imported Objects

From SNMPv2-MIB

snmpTraps

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
enterprises

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using npGsmFailed OID:

Select a NetPing DKSF-707 GSM/SMS bridge device as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type npGsmFailed into the Find box to locate it in the OID tree, then select it and click OK. It reports firmware's GSM module status. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value is anything other than 'ok', since that indicates the condition this object reports has changed to one worth investigating. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
lightcom	1.3.6.1.4.1.25728
INT npForcedReboot	1.3.6.1.4.1.25728.911.3	INTEGER	read-write	Write 1 to immediate forced reboot
npGsm	1.3.6.1.4.1.25728.3800
INT npGsmFailedEx	1.3.6.1.4.1.25728.3800.1.1	INTEGER	read-only	Firmware's GSM module status
npGsmInfo	1.3.6.1.4.1.25728.3800.1
INT npGsmRegistration	1.3.6.1.4.1.25728.3800.1.2	INTEGER	read-only	Status of modem registration in GSM network (AT+CREG? result)
STR npGsmSendSms	1.3.6.1.4.1.25728.3800.1.9	DisplayString	read-write	Send arbitrary SMS. Format: [phone_number,phone_number,...] Message One to four destination phone numbers If [] and numbers omitted, mesagge will be sent to preset numbers from SMS setup Only Latin characters allowed in message body
INT npGsmStrength	1.3.6.1.4.1.25728.3800.1.3	INTEGER	read-only	GSM signal strength. 0..31 = 0..100%, 99 = unknown or n/a, 255 = updating info
NTF npGsmTrap	1.3.6.1.4.1.25728.3800.2.0.1			GSM modem or SMS firmware problems
npGsmTrapPrefix	1.3.6.1.4.1.25728.3800.2.0
npGsmTraps	1.3.6.1.4.1.25728.3800.2
NTF npGsmTrapUnparsedSms	1.3.6.1.4.1.25728.3800.2.0.2			forwarding of SMS with wrong starting keyword
STR npGsmUnparsedRxSms	1.3.6.1.4.1.25728.3800.1.10	DisplayString	read-only	Received unparsed Sms with unknown starting word
STR npGsmUnparsedRxSmsFrom	1.3.6.1.4.1.25728.3800.1.11	DisplayString	read-only	Source phone of received unparsed (unknown) Sms
npReboot	1.3.6.1.4.1.25728.911
INT npResetStack	1.3.6.1.4.1.25728.911.2	INTEGER	read-write	Write 1 to re-initialize network stack
INT npSoftReboot	1.3.6.1.4.1.25728.911.1	INTEGER	read-write	Write 1 to reboot device after current operations completition
STR npTrapEmailTo	1.3.6.1.4.1.25728.90.1	DisplayString	read-only	user-specified e-mail for NetPing Trap Forwarding Service
npTrapInfo	1.3.6.1.4.1.25728.90
uniPingServerSolutionV3	1.3.6.1.4.1.25728.707			MIB for NetPing SMS gsm bridge

RFC description

Alentis Electronics NetPing SMS/GSM bridge MIB for managing GSM module status and SMS notification services.

Start monitoring NetPing DKSF-707 GSM/SMS bridge device with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DKSF-707-2-X-X-1