DES3016-L2MGMT-MIB

All MIBs › DES3016-L2MGMT-MIB

Organization: D-Link, Inc.

Last Updated: 2000-07-15

Description: Layer 2 management MIB for D-Link DES-3016 switch covering STP, IGMP, port mirroring, QoS scheduling, link aggregation, and loop detection

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DES3016-L2MGMT-MIB?

DES3016-L2MGMT-MIB is the Layer 2 management MIB for the D-Link DES-3016 switch, covering a broad set of switching features including Spanning Tree Protocol (STP), IGMP (multicast) snooping, port mirroring, QoS scheduling, link aggregation (trunking), and loop detection. It exposes configuration and status objects for each of these subsystems, letting administrators both configure and verify the switch's Layer 2 forwarding behavior. For status monitoring it is particularly useful for confirming STP port states to catch topology changes or blocked/forwarding transitions, trunk/link-aggregation member status to detect a failed trunk member, and loop-detection alarms to catch network loops causing broadcast storms, alongside IGMP group membership for multicast traffic health. It is a D-Link enterprise-specific MIB but conceptually builds on standard bridging (802.1D/802.1Q) and IGMP snooping concepts, and is typically used alongside standard BRIDGE-MIB/IF-MIB for complete switch visibility. It is deployed in small-to-midsize network environments using D-Link DES-3016 switches where administrators need Layer 2 redundancy, multicast, and QoS features monitored and managed via SNMP, and network staff can download the DES3016-L2MGMT-MIB file to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DES3016-L2MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DES-3016 switch

Monitoring Examples

An administrator would poll STP port state objects to confirm ports are correctly in forwarding or blocking state, and check link-aggregation/trunk membership tables to verify all expected physical ports are active members of a given trunk group. Loop-detection status objects would be monitored to catch an active loop condition, which typically manifests as a sudden broadcast/multicast storm alert. IGMP snooping group membership tables would be checked to confirm multicast streams are being correctly forwarded only to subscribed ports rather than flooded.

What Can Be Monitored

spanning tree port state
link aggregation/trunk member status
loop detection alarms
IGMP snooping group membership
port mirroring configuration
QoS scheduling configuration

Imported Objects

From DLINK-SWPRIMGMT-MIB

des3016

OBJECT-IDENTITY

From RFC1155-SMI

IpAddress

From RFC1213-MIB

DisplayString

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using swL2CPUutilizationIn5sec OID:

Select a D-Link DES-3016 switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type swL2CPUutilizationIn5sec into the Find box to locate it in the OID tree, then select it and click OK. It reports the time scale is 5 seconds.The value will be between 0%(idle) and 100% (very busy). On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if utilization exceeds 85%, a common warning threshold before sustained high load affects performance. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL2MgmtMIB	1.3.6.1.4.1.171.11.63.10.2			The Structure of Common Management Information for making a trunk and IGMP related function for D-Link devices.
swL2DevMgmt	1.3.6.1.4.1.171.11.63.10.2.1
swL2DevInfo	1.3.6.1.4.1.171.11.63.10.2.1.1
OCT swL2DevInfoFrontPanelLedStatus	1.3.6.1.4.1.171.11.63.10.2.1.1.5	OCTET STRING	read-only	This object is a set of system LED indications. The two octets is defined as system LED. The first LED is power LED. The second LED is console LED. The other octets following the second octets are the logical port LED (following dot1dBasePort ordering). Every two bytes are presented to a port. The first byte is presentd to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
swL2DevCtrl	1.3.6.1.4.1.171.11.63.10.2.1.2
INT swL2DevCtrlSystemReboot	1.3.6.1.4.1.171.11.63.10.2.1.2.1	INTEGER	read-write	This object indicates the agent system reboot state. The agent always returns other(1) when this object is read.
IP swL2DevCtrlSystemIP	1.3.6.1.4.1.171.11.63.10.2.1.2.2	IpAddress	read-write	This object indicates system ip.
IP swL2DevCtrlSubnetMask	1.3.6.1.4.1.171.11.63.10.2.1.2.3	IpAddress	read-write	This object indicates system subnet mask.
IP swL2DevCtrlDefaultGateway	1.3.6.1.4.1.171.11.63.10.2.1.2.4	IpAddress	read-write	This object indicates system default gateway.
VLA swL2DevCtrlManagementVlanId	1.3.6.1.4.1.171.11.63.10.2.1.2.5	VlanId	read-write	This object controls which Vlan includes system ip. And the Vlan should have been created.
INT swL2DevCtrlStpState	1.3.6.1.4.1.171.11.63.10.2.1.2.6	INTEGER	read-write	This object can be enabled or disabled spanning tree algorithm during runtime of the system.
INT swL2DevCtrlIGMPSnooping	1.3.6.1.4.1.171.11.63.10.2.1.2.7	INTEGER	read-write	This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled .
INT swL2DevCtrlCleanAllStatisticCounter	1.3.6.1.4.1.171.11.63.10.2.1.2.12	INTEGER	read-write	As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
INT swL2DevCtrlSnmpEnableAuthenTraps	1.3.6.1.4.1.171.11.63.10.2.1.2.13	INTEGER	read-write	Indicates whether the SNMP entity is permitted to generate authenticationFailure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authenticationFailure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant across re-initializations of the network management system.
INT swL2DevCtrlRmonState	1.3.6.1.4.1.171.11.63.10.2.1.2.16	INTEGER	read-write	This object can be enabled or disabled RMON.
INT swL2DevCtrlIpAutoConfig	1.3.6.1.4.1.171.11.63.10.2.1.2.17	INTEGER	read-write	Indicates the status of automatically getting configuration from TFTP server on device
INT swL2PortCtrlMulticastfilter	1.3.6.1.4.1.171.11.63.10.2.1.2.18	INTEGER	read-write	This object decide the multicast packets filtering mode on all port .
INT swL2MACNotifyState	1.3.6.1.4.1.171.11.63.10.2.1.2.19	INTEGER	read-write	This object can enabled or disabled MAC Notification.
INT swL2MACNotifyHistorySize	1.3.6.1.4.1.171.11.63.10.2.1.2.20	INTEGER	read-write	This object indicates the history size of variation MAC in address table. The default value is 1 .
INT swL2MACNotifyInterval	1.3.6.1.4.1.171.11.63.10.2.1.2.21	INTEGER	read-write	This object indicates the time interval in second for trigger the MAC notify message.
INT swL2DevCtrlVLANTrunkState	1.3.6.1.4.1.171.11.63.10.2.1.2.22	INTEGER	read-write	This indicates the global state of the VLAN trunking feature of the device.
INT swL2DevCtrlLLDPState	1.3.6.1.4.1.171.11.63.10.2.1.2.23	INTEGER	read-write	Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For receiving LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
INT swL2DevCtrlLLDPForwardMessageState	1.3.6.1.4.1.171.11.63.10.2.1.2.24	INTEGER	read-write	When lldp is disabled and lldp forward_message's are enabled, the LLDP Data Unit packets received by the switch will be forwarded.
VLA swL2DevCtrlVlanIdOfFDBTbl	1.3.6.1.4.1.171.11.63.10.2.1.2.25	VlanId	read-write	Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT_VLAN_ID of the system.
swL2CPUutilization	1.3.6.1.4.1.171.11.63.10.2.1.3
I32 swL2CPUutilizationIn5secEx	1.3.6.1.4.1.171.11.63.10.2.1.3.1	Integer32	read-only	Time scale is 5 seconds.The value will be between 0%(idle) and 100% (very busy).
I32 swL2CPUutilizationIn1min	1.3.6.1.4.1.171.11.63.10.2.1.3.2	Integer32	read-only	Time scale is 1 minute.The value will be between 0%(idle) and 100% (very busy).
I32 swL2CPUutilizationIn5min	1.3.6.1.4.1.171.11.63.10.2.1.3.3	Integer32	read-only	Time scale is 5 minute.The value will be between 0%(idle) and 100% (very busy).
swL2DevAlarm	1.3.6.1.4.1.171.11.63.10.2.1.4
INT swL2DevAlarmLinkChange	1.3.6.1.4.1.171.11.63.10.2.1.4.3	INTEGER	read-write	This object determines whether or not to send a trap message when the link changes. If the object is enabled (3), the Link Change trap is sent by the device when any of its port links change. The device does not send the trap if this object value is disabled or in another state.
swL2PortMgmt	1.3.6.1.4.1.171.11.63.10.2.2
swL2PortInfoTable	1.3.6.1.4.1.171.11.63.10.2.2.1		not-accessible	A table that contains information about every port.
swL2PortInfoEntry	1.3.6.1.4.1.171.11.63.10.2.2.1.1		not-accessible	A list of information for each port of the device.
INT swL2PortInfoPortIndex	1.3.6.1.4.1.171.11.63.10.2.2.1.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortInfoLinkStatus	1.3.6.1.4.1.171.11.63.10.2.2.1.1.4	INTEGER	read-only	This object indicates the port link status.
INT swL2PortInfoNwayStatus	1.3.6.1.4.1.171.11.63.10.2.2.1.1.5	INTEGER	read-only	This object indicates the port speed and duplex mode.
swL2PortCtrlTable	1.3.6.1.4.1.171.11.63.10.2.2.2		not-accessible	A table that contains control information about every port.
swL2PortCtrlEntry	1.3.6.1.4.1.171.11.63.10.2.2.2.1		not-accessible	A list of control information for each port of the device.
INT swL2PortCtrlPortIndex	1.3.6.1.4.1.171.11.63.10.2.2.2.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortCtrlAdminState	1.3.6.1.4.1.171.11.63.10.2.2.2.1.2	INTEGER	read-write	This object decide the port enabled or disabled.
INT swL2PortCtrlNwayState	1.3.6.1.4.1.171.11.63.10.2.2.2.1.3	INTEGER	read-write	Chose the port speed, duplex mode, and N-Way function mode.
INT swL2PortCtrlFlowCtrlState	1.3.6.1.4.1.171.11.63.10.2.2.2.1.4	INTEGER	read-write	Set flow control function as enabled or disabled.
STR swL2PortCtrlDescription	1.3.6.1.4.1.171.11.63.10.2.2.2.1.5	DisplayString	read-write	The object describe the ports in text.
INT swL2PortCtrlMACNotifyState	1.3.6.1.4.1.171.11.63.10.2.2.2.1.7	INTEGER	read-write	This object set each poet MAC notification state.
INT swL2PortCtrlMDIXState	1.3.6.1.4.1.171.11.63.10.2.2.2.1.10	INTEGER	read-write	This object controls the MDIX state of a specified port.
swL2PortErrTable	1.3.6.1.4.1.171.11.63.10.2.2.3		not-accessible	A table that contains information about Err port.
swL2PortErrEntry	1.3.6.1.4.1.171.11.63.10.2.2.3.1		not-accessible	A list of information for err port of the device.
INT swL2PortErrPortIndex	1.3.6.1.4.1.171.11.63.10.2.2.3.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortErrPortState	1.3.6.1.4.1.171.11.63.10.2.2.3.1.2	INTEGER	read-only	This object decide the portstate enabled or disabled.
INT swL2PortErrPortStatus	1.3.6.1.4.1.171.11.63.10.2.2.3.1.3	INTEGER	read-only	This object decide the PortStatus whether err-disabled.
INT swL2PortErrPortReason	1.3.6.1.4.1.171.11.63.10.2.2.3.1.4	INTEGER	read-only	This object decide the PortStatus STP LBD or Storm control.
STR swL2PortErrDescription	1.3.6.1.4.1.171.11.63.10.2.2.3.1.5	DisplayString	read-only	The object describe the ports in text.
swL2QOSMgmt	1.3.6.1.4.1.171.11.63.10.2.3
swL2QOSBandwidthControlTable	1.3.6.1.4.1.171.11.63.10.2.3.1		not-accessible	.
swL2QOSBandwidthControlEntry	1.3.6.1.4.1.171.11.63.10.2.3.1.1		not-accessible	A list of information contained in swL2QOSBandwidthControlTable.
INT swL2QOSBandwidthPortIndex	1.3.6.1.4.1.171.11.63.10.2.3.1.1.1	INTEGER	read-only	Indicates the port .
INT swL2QOSBandwidthRxRate	1.3.6.1.4.1.171.11.63.10.2.3.1.1.2	INTEGER	read-write	Indicates RX Rate(Mbit/sec) of the specifed port.Value 1024000 means no limit.
INT swL2QOSBandwidthTxRate	1.3.6.1.4.1.171.11.63.10.2.3.1.1.3	INTEGER	read-write	Indicates TX Rate(Mbit/sec) of the specifed port.Value 1024000 means no limit.
INT swL2QOSBandwidthRadiusRxRate	1.3.6.1.4.1.171.11.63.10.2.3.1.1.4	INTEGER	read-only	The RxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured RxRate.
INT swL2QOSBandwidthRadiusTxRate	1.3.6.1.4.1.171.11.63.10.2.3.1.1.5	INTEGER	read-only	The TxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured TxRate.
swL2QOSSchedulingTable	1.3.6.1.4.1.171.11.63.10.2.3.2		not-accessible	.
swL2QOSSchedulingEntry	1.3.6.1.4.1.171.11.63.10.2.3.2.1		not-accessible	A list of information contained in swL2QOSSchedulingTable.
INT swL2QOSSchedulingClassIndex	1.3.6.1.4.1.171.11.63.10.2.3.2.1.1	INTEGER	read-only	Indicates the hardware queue number.
INT swL2QOSSchedulingMaxWeight	1.3.6.1.4.1.171.11.63.10.2.3.2.1.4	INTEGER	read-write
swL2QOS8021pUserPriorityTable	1.3.6.1.4.1.171.11.63.10.2.3.3		not-accessible	.
swL2QOS8021pUserPriorityEntry	1.3.6.1.4.1.171.11.63.10.2.3.3.1		not-accessible	A list of information contained in swL2QOS8021pUserPriorityTable.
INT swL2QOS8021pUserPriorityIndex	1.3.6.1.4.1.171.11.63.10.2.3.3.1.1	INTEGER	read-only	The 802.1p user priority .
INT swL2QOS8021pUserPriorityClass	1.3.6.1.4.1.171.11.63.10.2.3.3.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
swL2QOS8021pDefaultPriorityTable	1.3.6.1.4.1.171.11.63.10.2.3.4		not-accessible	.
swL2QOS8021pDefaultPriorityEntry	1.3.6.1.4.1.171.11.63.10.2.3.4.1		not-accessible	A list of information contained in swL2QOS8021pDefaultPriorityTable.
INT swL2QOS8021pDefaultPriorityIndex	1.3.6.1.4.1.171.11.63.10.2.3.4.1.1	INTEGER	read-only	Indicates the port number .
INT swL2QOS8021pDefaultPriority	1.3.6.1.4.1.171.11.63.10.2.3.4.1.2	INTEGER	read-write	The priority value to assign to untagged packets received by the switch ports on the switch..
INT swL2QOS8021pRadiusPriority	1.3.6.1.4.1.171.11.63.10.2.3.4.1.3	INTEGER	read-only	The value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
INT swL2QOSSchedulingMechanismCtrl	1.3.6.1.4.1.171.11.63.10.2.3.5	INTEGER	read-write	This object can control QOS scheduling Mechanism.
swL2TrunkMgmt	1.3.6.1.4.1.171.11.63.10.2.4
I32 swPortTrunkMaxEntries	1.3.6.1.4.1.171.11.63.10.2.4.1	Integer32	read-only	The max entries of swPortTrunkTable
I32 swPortTrunkMaxPortMembers	1.3.6.1.4.1.171.11.63.10.2.4.2	Integer32	read-only	The max number of ports allowed in a trunk.
swPortTrunkTable	1.3.6.1.4.1.171.11.63.10.2.4.3		not-accessible	This table specifies the port membership for each logical link.
swPortTrunkEntry	1.3.6.1.4.1.171.11.63.10.2.4.3.1		not-accessible	A list of information specifies which ports group form a single logical link.
I32 swPortTrunkIndex	1.3.6.1.4.1.171.11.63.10.2.4.3.1.1	Integer32	read-only	The index of logical port trunk.
I32 swPortTrunkMasterPort	1.3.6.1.4.1.171.11.63.10.2.4.3.1.2	Integer32	read-create	The object indicates the master port number of the port trunk entry.The first port of the trunk is implicitly configured to be the master logical port.When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
POR swPortTrunkPortList	1.3.6.1.4.1.171.11.63.10.2.4.3.1.3	PortList	read-create	Indicate member ports of a logical trunk.
INT swPortTrunkType	1.3.6.1.4.1.171.11.63.10.2.4.3.1.4	INTEGER	read-create	This object indicates the type of this entry.
POR swPortTrunkActivePort	1.3.6.1.4.1.171.11.63.10.2.4.3.1.5	PortList	read-only	This object indicates the active ports of this entry.
ROW swPortTrunkState	1.3.6.1.4.1.171.11.63.10.2.4.3.1.6	RowStatus	read-create	This object indicates the status of this entry. when the state is CreatAndGo(4),the type of trunk is static(1); when the state is CreatAndWait(5),the type of trunk is lacp(2).
I32 swPortTrunkFloodingPort	1.3.6.1.4.1.171.11.63.10.2.4.3.1.7	Integer32	read-only	The flooding port of every trunk.
INT swL2TrunkAlgorithm	1.3.6.1.4.1.171.11.63.10.2.4.4	INTEGER	read-write	This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
swL2TrunkLACPPortTable	1.3.6.1.4.1.171.11.63.10.2.4.5		not-accessible	This table specifys which ports group a set of ports(up to 8) into a single logical link.
swL2TrunkLACPPortEntry	1.3.6.1.4.1.171.11.63.10.2.4.5.1		not-accessible	A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
INT swL2TrunkLACPPortIndex	1.3.6.1.4.1.171.11.63.10.2.4.5.1.1	INTEGER	read-only	The index of logical port lacp.
INT swL2TrunkLACPPortState	1.3.6.1.4.1.171.11.63.10.2.4.5.1.2	INTEGER	read-write	The state of logical port lacp.
swL2TrunkVLANTable	1.3.6.1.4.1.171.11.63.10.2.4.6		not-accessible	This table is used to manage the VLAN trunking feature of the device.
swL2TrunkVLANEntry	1.3.6.1.4.1.171.11.63.10.2.4.6.1		not-accessible	This object is used to configure the VLAN trunking settings for each port.
INT swL2TrunkVLANPort	1.3.6.1.4.1.171.11.63.10.2.4.6.1.1	INTEGER	read-only	This object indicates the port being configured.
INT swL2TrunkVLANState	1.3.6.1.4.1.171.11.63.10.2.4.6.1.2	INTEGER	read-write	The state of the logical port LACP.
swPortMirrorPackage	1.3.6.1.4.1.171.11.63.10.2.6
POR swPortMirrorRxPortList	1.3.6.1.4.1.171.11.63.10.2.6.2	PortList	read-write	This object indicates the Rx port list of ports to be sniffed.
POR swPortMirrorTxPortList	1.3.6.1.4.1.171.11.63.10.2.6.3	PortList	read-write	This object indicates the Tx port list of ports to be sniffed.
I32 swPortMirrorTargetPort	1.3.6.1.4.1.171.11.63.10.2.6.4	Integer32	read-write	This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.
INT swPortMirrorState	1.3.6.1.4.1.171.11.63.10.2.6.5	INTEGER	read-write	This object indicates the status of this entry.
swIGMPPackage	1.3.6.1.4.1.171.11.63.10.2.7
INT swL2IGMPMaxSupportedVlans	1.3.6.1.4.1.171.11.63.10.2.7.1	INTEGER	read-only	Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPMaxIpGroupNumPerVlan	1.3.6.1.4.1.171.11.63.10.2.7.2	INTEGER	read-only	Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).
swL2IGMPCtrlTable	1.3.6.1.4.1.171.11.63.10.2.7.3		not-accessible	The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12.
swL2IGMPCtrlEntry	1.3.6.1.4.1.171.11.63.10.2.7.3.1		not-accessible	The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
INT swL2IGMPCtrlVid	1.3.6.1.4.1.171.11.63.10.2.7.3.1.1	INTEGER	read-only	This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.
INT swL2IGMPQueryInterval	1.3.6.1.4.1.171.11.63.10.2.7.3.1.2	INTEGER	read-write	The frequency at which IGMP Host-Query packets are transmitted on this switch.
INT swL2IGMPMaxResponseTime	1.3.6.1.4.1.171.11.63.10.2.7.3.1.3	INTEGER	read-write	The maximum query response time on this switch.
INT swL2IGMPRobustness	1.3.6.1.4.1.171.11.63.10.2.7.3.1.4	INTEGER	read-write	The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
INT swL2IGMPLastMemberQueryInterval	1.3.6.1.4.1.171.11.63.10.2.7.3.1.5	INTEGER	read-write	The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
INT swL2IGMPHostTimeout	1.3.6.1.4.1.171.11.63.10.2.7.3.1.6	INTEGER	read-write	The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.
INT swL2IGMPRouteTimeout	1.3.6.1.4.1.171.11.63.10.2.7.3.1.7	INTEGER	read-write	The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
INT swL2IGMPLeaveTimer	1.3.6.1.4.1.171.11.63.10.2.7.3.1.8	INTEGER	read-write	When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
INT swL2IGMPQueryState	1.3.6.1.4.1.171.11.63.10.2.7.3.1.9	INTEGER	read-write	This object decide the IGMP query enabled or disabled.
INT swL2IGMPCurrentState	1.3.6.1.4.1.171.11.63.10.2.7.3.1.10	INTEGER	read-only	This object indicates the current IGMP query state.
INT swL2IGMPCtrlState	1.3.6.1.4.1.171.11.63.10.2.7.3.1.11	INTEGER	read-write	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry.
INT swL2IGMPFastLeave	1.3.6.1.4.1.171.11.63.10.2.7.3.1.12	INTEGER	read-write
swL2IGMPQueryInfoTable	1.3.6.1.4.1.171.11.63.10.2.7.4		not-accessible	The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.
swL2IGMPQueryInfoEntry	1.3.6.1.4.1.171.11.63.10.2.7.4.1		not-accessible	Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.
INT swL2IGMPInfoVid	1.3.6.1.4.1.171.11.63.10.2.7.4.1.1	INTEGER	read-only	This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPInfoQueryCount	1.3.6.1.4.1.171.11.63.10.2.7.4.1.2	INTEGER	read-only	This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.
INT swL2IGMPInfoTxQueryCount	1.3.6.1.4.1.171.11.63.10.2.7.4.1.3	INTEGER	read-only	This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
swL2IGMPInfoTable	1.3.6.1.4.1.171.11.63.10.2.7.5		not-accessible	The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also.
swL2IGMPInfoEntry	1.3.6.1.4.1.171.11.63.10.2.7.5.1		not-accessible	Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.
INT swL2IGMPVid	1.3.6.1.4.1.171.11.63.10.2.7.5.1.1	INTEGER	read-only	This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.
IP swL2IGMPGroupIpAddr	1.3.6.1.4.1.171.11.63.10.2.7.5.1.2	IpAddress	read-only	This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.
MAC swL2IGMPMacAddr	1.3.6.1.4.1.171.11.63.10.2.7.5.1.3	MacAddress	read-only	This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.
POR swL2IGMPPortMap	1.3.6.1.4.1.171.11.63.10.2.7.5.1.4	PortList	read-only	This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero.
INT swL2IGMPIpGroupReportCount	1.3.6.1.4.1.171.11.63.10.2.7.5.1.5	INTEGER	read-only	This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.
swL2IGMPRouterPortTable	1.3.6.1.4.1.171.11.63.10.2.7.6		not-accessible	The information of the router port table.
swL2IGMPRouterPortEntry	1.3.6.1.4.1.171.11.63.10.2.7.6.1		not-accessible	The entry of swL2IGMPRouterPortTable.
INT swL2IGMPRouterPortVlanid	1.3.6.1.4.1.171.11.63.10.2.7.6.1.1	INTEGER	read-only	This object indicates the VLAN ID of the router port entry.
STR swL2IGMPRouterPortVlanName	1.3.6.1.4.1.171.11.63.10.2.7.6.1.2	DisplayString	read-only	This object indicates the VLAN name of the router port entry.
POR swL2IGMPRouterPortStaticPortList	1.3.6.1.4.1.171.11.63.10.2.7.6.1.3	PortList	read-write	This object indicates the static portlist of the router port entry.
POR swL2IGMPRouterPortDynamicPortList	1.3.6.1.4.1.171.11.63.10.2.7.6.1.4	PortList	read-only	This object indicates the dynamic portlist of the router port entry.
POR swL2IGMPRouterPortForbiddenPortList	1.3.6.1.4.1.171.11.63.10.2.7.6.1.5	PortList	read-write	This object indicate the forbidden portlist of the router port entry.
swL2IGMPAccessAuthTable	1.3.6.1.4.1.171.11.63.10.2.7.7		not-accessible	This table is used to manage the IGMP Access Authentication configurations of the device.
swL2IGMPAccessAuthEntry	1.3.6.1.4.1.171.11.63.10.2.7.7.1		not-accessible	A list of manageable entities for IGMP Access Authentication. The configuration is done per port.
INT swL2IGMPAccessAuthPort	1.3.6.1.4.1.171.11.63.10.2.7.7.1.1	INTEGER	read-only	The index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.
INT swL2IGMPAccessAuthState	1.3.6.1.4.1.171.11.63.10.2.7.7.1.2	INTEGER	read-write	This object denotes the status of IGMP Access Authentication of the port.
swL2TrafficMgmt	1.3.6.1.4.1.171.11.63.10.2.11
swL2TrafficCtrlTable	1.3.6.1.4.1.171.11.63.10.2.11.1		not-accessible	This table specifys the storm traffic control configuration.
swL2TrafficCtrlEntry	1.3.6.1.4.1.171.11.63.10.2.11.1.1		not-accessible	A list of information specifies the storm traffic control configuration.
INT swL2TrafficCtrlGroupIndex	1.3.6.1.4.1.171.11.63.10.2.11.1.1.1	INTEGER	read-only	The index of logical port trunk. The trunk group number depend on the existence of unit and module.
INT swL2TrafficCtrlUnitIndex	1.3.6.1.4.1.171.11.63.10.2.11.1.1.2	INTEGER	read-only	Indicates ID of the unit in the device
INT swL2TrafficCtrlBMStromthreshold	1.3.6.1.4.1.171.11.63.10.2.11.1.1.3	INTEGER	read-write	This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl, swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlUcastStromCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured amount of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet.
INT swL2TrafficCtrlBcastStromCtrl	1.3.6.1.4.1.171.11.63.10.2.11.1.1.4	INTEGER	read-write	This object indicates broadcast storm control function is enabled or disabled.
INT swL2TrafficCtrlMcastStromCtrl	1.3.6.1.4.1.171.11.63.10.2.11.1.1.5	INTEGER	read-write	This object indicates multicast storm control function is enabled or disabled.
INT swL2TrafficCtrlUcastStromCtrl	1.3.6.1.4.1.171.11.63.10.2.11.1.1.6	INTEGER	read-write	This object indicates destination lookup fail function is enabled or disabled.
swL2TrafficSegMgmt	1.3.6.1.4.1.171.11.63.10.2.12
swL2TrafficSegTable	1.3.6.1.4.1.171.11.63.10.2.12.1		not-accessible	This table specifys the port just can forward traffic to the specific port list.
swL2TrafficSegEntry	1.3.6.1.4.1.171.11.63.10.2.12.1.1		not-accessible	A list of information specifies the port with its traffic forward list.
INT swL2TrafficSegPort	1.3.6.1.4.1.171.11.63.10.2.12.1.1.1	INTEGER	read-only	The port number of the logical port.
POR swL2TrafficSegForwardPorts	1.3.6.1.4.1.171.11.63.10.2.12.1.1.2	PortList	read-write	The port list that the specific port can forward traffic.
swL2PortSecurityMgmt	1.3.6.1.4.1.171.11.63.10.2.15
swL2PortSecurityControlTable	1.3.6.1.4.1.171.11.63.10.2.15.1		not-accessible	port security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as static entry. When the learned addresses number reach N, any coming packet with not learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port.
swL2PortSecurityControlEntry	1.3.6.1.4.1.171.11.63.10.2.15.1.1		not-accessible	A list of information contained in swL2PortSecurityControlTable.
INT swL2PortSecurityPortIndex	1.3.6.1.4.1.171.11.63.10.2.15.1.1.1	INTEGER	read-only	Indicates the secured port to lock address learning.
INT swL2PortSecurityMaxLernAddr	1.3.6.1.4.1.171.11.63.10.2.15.1.1.2	INTEGER	read-write	Indicates allowable number of addresses to be learned at this port.
INT swL2PortSecurityMode	1.3.6.1.4.1.171.11.63.10.2.15.1.1.3	INTEGER	read-write	Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locked address is aged out, the number of address can be learned has to be increased by one. In deleteOnReset(4) mode - never age out the locked addresses unless restart the system to prevent from port movement or intrusion.
INT swL2PortSecurityAdmState	1.3.6.1.4.1.171.11.63.10.2.15.1.1.4	INTEGER	read-write	Indicates administration state of locking address.
INT swL2PortSecurityEntryClearCtrl	1.3.6.1.4.1.171.11.63.10.2.15.1.1.5	INTEGER	read-write	Used to clear port security entries by port. Setting this value to 'start' will execute the clear action, Once cleared, the value returns to 'other'.
INT swL2PortSecurityTrapLogState	1.3.6.1.4.1.171.11.63.10.2.15.2	INTEGER	read-write	when enable(2),whenever there's a new MAC that violates the pre-defined port security configuration, trap will be sent out and the relevant information will be logged in system.
swL2StpMgmt	1.3.6.1.4.1.171.11.63.10.2.16
INT swL2StpForwardBPDU	1.3.6.1.4.1.171.11.63.10.2.16.1	INTEGER	read-write	Indicates whether flooding BPDU packets when STP is disabled on device
swL2StpPortTable	1.3.6.1.4.1.171.11.63.10.2.16.4		not-accessible	A table that contains port-specific information for the Spanning Tree Protocol.
swL2StpPortEntry	1.3.6.1.4.1.171.11.63.10.2.16.4.1		not-accessible	A list of information maintained by every port about the Spanning Tree Protocol state for that port.
INT swL2StpPort	1.3.6.1.4.1.171.11.63.10.2.16.4.1.1	INTEGER	read-only	The port number of the port for this entry.
INT swL2StpPortStatus	1.3.6.1.4.1.171.11.63.10.2.16.4.1.3	INTEGER	read-only	When the port Enable state is enabled, the port's current state as defined by application of the Spanning Tree Protocol. If the PortEnable is disabled, the the port status will be no-stp-enabled(7). If the port is in error disabled status, the port status will be err-disabled(8)
INT swL2StpPortRole	1.3.6.1.4.1.171.11.63.10.2.16.4.1.4	INTEGER	read-only	When the port Enable state is enabled, the port's current port role as defined by application of the Spanning Tree Protocol. If the Port Enable state is disabled, the the port role will be nonstp(7). If the port is in loop-back status, the port role will be loopback(8)
INT swL2StpPortFBPDU	1.3.6.1.4.1.171.11.63.10.2.16.4.1.5	INTEGER	read-write	The enabled/disabled status is used to BPDU Filtering attached to this port.
INT swL2StpPortLinkState	1.3.6.1.4.1.171.11.63.10.2.16.4.1.6	INTEGER	read-only	This object indicates the stp port speed and duplex mode.
T/F swL2StpPortProtocolMigration	1.3.6.1.4.1.171.11.63.10.2.16.4.1.7	TruthValue	read-write	When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.
INT swL2StpPortAdminEdgePort	1.3.6.1.4.1.171.11.63.10.2.16.4.1.8	INTEGER	read-write	The administrative value of the Edge Port parameter. A value of TRUE(0) indicates that this port should be assumed as an edge-port and a value of FALSE(1) indicates that this port should be assumed as a non-edge-port.
T/F swL2StpPortOperEdgePort	1.3.6.1.4.1.171.11.63.10.2.16.4.1.9	TruthValue	read-only	The operational value of the Edge Port parameter. The object is initialized to the value of swL2StpPortAdminEdgePort and is set FALSE on reception of a BPDU.
INT swL2StpPortAdminPointToPoint	1.3.6.1.4.1.171.11.63.10.2.16.4.1.10	INTEGER	read-write	The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
T/F swL2StpPortOperPointToPoint	1.3.6.1.4.1.171.11.63.10.2.16.4.1.11	TruthValue	read-only	The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the swL2StpPortAdminPointToPoint object.
U32 swL2StpPortAdminPathCost	1.3.6.1.4.1.171.11.63.10.2.16.4.1.12	Unsigned32	read-write	The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object swL2StpPortPathCost, which returns the operational value of the path cost. Issue No.: 3250R2-077 As USE_RSTP is 1:enabled, swL2StpPortPathCost is forced to be read-only. configuration via swL2StpPortAdminPathCost. According 802.1w, value range of swL2StpPortAdminPathCost would be expanded. the former value range is (0..65535), the new is (0..200000000).
INT swL2StpPortPriority	1.3.6.1.4.1.171.11.63.10.2.16.4.1.13	INTEGER	read-write	The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of swL2StpPort.
INT swL2STPPortState	1.3.6.1.4.1.171.11.63.10.2.16.4.1.14	INTEGER	read-write	The enabled/disabled status is usedoop-back prevention attached to this port.
T/F swL2StpPortRestrictedRole	1.3.6.1.4.1.171.11.63.10.2.16.4.1.15	TruthValue	read-write	If TRUE causes the port not to be selected as Root Port, even it has the best spanning tree priotiry vector.
T/F swL2StpPortRestrictedTCN	1.3.6.1.4.1.171.11.63.10.2.16.4.1.16	TruthValue	read-write	If TRUE causes the port not to propagate received topology change notifications and topology changes to other Ports.
swL2CosMgmt	1.3.6.1.4.1.171.11.63.10.2.17
swL2CosPriorityCtrl	1.3.6.1.4.1.171.11.63.10.2.17.3
swL2CosPriorityTable	1.3.6.1.4.1.171.11.63.10.2.17.3.1		not-accessible	Used to show and config per port priority-based QoS features on the switch
swL2CosPriorityEntry	1.3.6.1.4.1.171.11.63.10.2.17.3.1.1		not-accessible	A list of information contained in swL2CosPriorityTable.
INT swL2CosPriorityPort	1.3.6.1.4.1.171.11.63.10.2.17.3.1.1.1	INTEGER	read-only	The port number of CoS Priority.
INT swL2CosPriorityPortPRI	1.3.6.1.4.1.171.11.63.10.2.17.3.1.1.2	INTEGER	read-write	Indicates port_priority state for CoS.
INT swL2CosPriorityEtherPRI	1.3.6.1.4.1.171.11.63.10.2.17.3.1.1.3	INTEGER	read-write	Enable Ethernet frame based priority. When set ether8021p(2), enable 802.1p QoS; When set macBase(3), enable MAC-based QoS; When set disable(1), disable Ethernet frame based priority.
INT swL2CosPriorityIpPRI	1.3.6.1.4.1.171.11.63.10.2.17.3.1.1.4	INTEGER	read-write	Enable IP priority QoS. When set tos(2), enable TOS based QoS; When set dscp(3), enable DSCP based QoS; When set disable(1), disable IP priority QoS.
INT swL2CosPriorityNone	1.3.6.1.4.1.171.11.63.10.2.17.3.1.1.5	INTEGER	read-write	when read,it always return invalid(2); when write valid(1),it disables all priority in this table.
swL2CosPortPRITable	1.3.6.1.4.1.171.11.63.10.2.17.3.2		not-accessible	Used to show port-to-class mappings and map specific port to one of the hardware queues available on the switch.
swL2CosPortPRIEntry	1.3.6.1.4.1.171.11.63.10.2.17.3.2.1		not-accessible	A list of information contained in swL2CosPortPRITable.
INT swL2CosPortPRIIndex	1.3.6.1.4.1.171.11.63.10.2.17.3.2.1.1	INTEGER	read-only	Indicates CoS Priority PortPRI.
INT swL2CosPortPRIClass	1.3.6.1.4.1.171.11.63.10.2.17.3.2.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges. And you can set value only 0 or 3,you can't set value 1 or 2.
swL2CosMacBasePRITable	1.3.6.1.4.1.171.11.63.10.2.17.3.3		not-accessible	Used to show MAC priority map to traffic class and map the destination MAC address in incoming packet to one of the hardware queues available on the switch.
swL2CosMacBasePRIEntry	1.3.6.1.4.1.171.11.63.10.2.17.3.3.1		not-accessible	A list of information contained in swL2CosMacBasePRITable.
MAC swL2CosMacBasePRIIndex	1.3.6.1.4.1.171.11.63.10.2.17.3.3.1.1	MacAddress	read-only	Indicates CoS Priority MacBasePRI.
INT swL2CosMacBasePRIClass	1.3.6.1.4.1.171.11.63.10.2.17.3.3.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges.
swL2CosTosPRITable	1.3.6.1.4.1.171.11.63.10.2.17.3.4		not-accessible	Used to show TOS value to traffic class mapping and map the TOS value in the IP header of incoming packet to one of the four hardware queues available on the switch.
swL2CosTosPRIEntry	1.3.6.1.4.1.171.11.63.10.2.17.3.4.1		not-accessible	A list of information contained in swL2CosTosPRITable.
INT swL2CosTosPRIIndex	1.3.6.1.4.1.171.11.63.10.2.17.3.4.1.1	INTEGER	read-only	Indicates CoS Priority TosPRI.
INT swL2CosTosPRIClass	1.3.6.1.4.1.171.11.63.10.2.17.3.4.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges.
swL2CosDscpPRITable	1.3.6.1.4.1.171.11.63.10.2.17.3.5		not-accessible	Used to show DSCP value to traffic class mapping and map the DSCP value in the IP header of incoming packet to one of the hardware queues available on the switch.
swL2CosDscpPRIEntry	1.3.6.1.4.1.171.11.63.10.2.17.3.5.1		not-accessible	A list of information contained in swL2CosDscpPRITable.
INT swL2CosDscpPRIIndex	1.3.6.1.4.1.171.11.63.10.2.17.3.5.1.1	INTEGER	read-only	Indicates CoS Priority DscpPRI.
INT swL2CosDscpPRIClass	1.3.6.1.4.1.171.11.63.10.2.17.3.5.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges.
swL2LoopDetectMgmt	1.3.6.1.4.1.171.11.63.10.2.18
swL2LoopDetectCtrl	1.3.6.1.4.1.171.11.63.10.2.18.1
INT swL2LoopDetectAdminState	1.3.6.1.4.1.171.11.63.10.2.18.1.1	INTEGER	read-write	This object indicates the loopback detection status for the system.
INT swL2LoopDetectInterval	1.3.6.1.4.1.171.11.63.10.2.18.1.2	INTEGER	read-write	This object indicates the interval value, the range is from 1 to 32767 seconds.
INT swL2LoopDetectRecoverTime	1.3.6.1.4.1.171.11.63.10.2.18.1.3	INTEGER	read-write	This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
swL2LoopDetectPortMgmt	1.3.6.1.4.1.171.11.63.10.2.18.2
swL2LoopDetectPortTable	1.3.6.1.4.1.171.11.63.10.2.18.2.1		not-accessible	The table specifies the loopback detection function specified by port.
swL2LoopDetectPortEntry	1.3.6.1.4.1.171.11.63.10.2.18.2.1.1		not-accessible	The table specifies the loopback detection function specified by port.
INT swL2LoopDetectPortIndex	1.3.6.1.4.1.171.11.63.10.2.18.2.1.1.1	INTEGER	read-only	This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
INT swL2LoopDetectPortState	1.3.6.1.4.1.171.11.63.10.2.18.2.1.1.2	INTEGER	read-write	This object indicates the loopback detection function state on the port.
INT swL2LoopDetectPortLoopStatus	1.3.6.1.4.1.171.11.63.10.2.18.2.1.1.4	INTEGER	read-only	This object indicates the port status.
swL2VLANMgmt	1.3.6.1.4.1.171.11.63.10.2.19
swL2VlanTable	1.3.6.1.4.1.171.11.63.10.2.19.1		not-accessible	A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
swL2VlanEntry	1.3.6.1.4.1.171.11.63.10.2.19.1.1		not-accessible	Static information for a VLAN configured into the device by (local or network) management.
VLA swL2VlanIndex	1.3.6.1.4.1.171.11.63.10.2.19.1.1.1	VlanId	read-only	The VLAN ID of the VLAN to be created. The range is 1 - 4094.
STR swL2VlanName	1.3.6.1.4.1.171.11.63.10.2.19.1.1.2	DisplayString	read-only	The name of the VLAN to be displayed.
INT swL2VlanType	1.3.6.1.4.1.171.11.63.10.2.19.1.1.3	INTEGER	read-only	The type of the VLAN to be displayed.
POR swL2VlanMemberPorts	1.3.6.1.4.1.171.11.63.10.2.19.1.1.4	PortList	read-only	A range of member ports to the VLAN.
POR swL2VlanStaticPorts	1.3.6.1.4.1.171.11.63.10.2.19.1.1.5	PortList	read-only	A range of static ports to the VLAN.
POR swL2VlanUntaggedPorts	1.3.6.1.4.1.171.11.63.10.2.19.1.1.6	PortList	read-only	Specifies the additional ports as untagged.
POR swL2VlanTaggedPorts	1.3.6.1.4.1.171.11.63.10.2.19.1.1.7	PortList	read-only	Specifies the additional ports as tagged.
swL2MgmtMIBTraps	1.3.6.1.4.1.171.11.63.10.2.100
swL2Notify	1.3.6.1.4.1.171.11.63.10.2.100.1
swL2NotifyPrefix	1.3.6.1.4.1.171.11.63.10.2.100.1.2
swL2NotifFirmware	1.3.6.1.4.1.171.11.63.10.2.100.1.2.0
NTF swL2macNotification	1.3.6.1.4.1.171.11.63.10.2.100.1.2.0.1			This trap indicates the MAC addresses variation in address table .
NTF swL2PortSecurityViolationTrap	1.3.6.1.4.1.171.11.63.10.2.100.1.2.0.2			When the port_security trap is enabled, new MAC addresses that violate the pre-defined port security configuration will trigger trap messages to be sent out.
swl2NotificationBidings	1.3.6.1.4.1.171.11.63.10.2.100.1.2.1
OCT swL2macNotifyInfo	1.3.6.1.4.1.171.11.63.10.2.100.1.2.1.1	OCTET STRING	read-only	This object indicates the last time reboot information.
MAC swL2PortSecurityViolationMac	1.3.6.1.4.1.171.11.63.10.2.100.1.2.1.2	MacAddress	accessible-for-notify	This object indicates the MAC address that violates the port security configuration.

RFC description

D-Link DES3016 Layer 2 switch management with trunking, IGMP, and link aggregation features.

Start monitoring D-Link DES-3016 switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DES3016-L2MGMT-MIB