CT-ELS10-MIB

All MIBs › CT-ELS10-MIB

Category: VLAN and Bridging, Vendor: Cabletron/Enterasys

Description: Manages Cabletron ELS10 series entry-level switch hardware, port status, and basic switching parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CT-ELS10-MIB?

CT-ELS10-MIB is a Cabletron Systems proprietary MIB for the ELS10 series entry-level Ethernet switches, providing hardware configuration and basic Layer 2 switching parameters similar to its ELS10-27 sibling module. It exposes per-port protocol settings (bridging, BPDU suppression, RIP listening, trunking) and VLAN/trunk table configuration for the switch's fixed port set. It supports monitoring of switch software status by confirming spanning-tree, trunking, and VLAN configuration is applied as intended on each port, helping detect misconfigurations that cause loops or unreachable segments. It builds on Cabletron's standard bridge/VLAN MIB conventions and ties into ifIndex-based interface tables. It was deployed in small enterprise or branch-office wiring closets running the ELS10 as an inexpensive, lightly managed workgroup switch. Engineers can download the CT-ELS10-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CT-ELS10-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cabletron ELS10 series entry-level Ethernet switch

Monitoring Examples

Polling els10-27protoTable entries (the shared object naming convention across the ELS10 family) via els10-27protoIfIndex exposes each port's els10-27protoBridge and els10-27protoTrunking state, letting an operator confirm no port has trunking unexpectedly enabled. The els10-27trunkTable indexed by els10-27trunkIfIndex shows configured trunk links, useful for validating uplink configuration after a firmware upgrade. Because this MIB shares its object set with CT-ELS10-27-MIB, administrators should verify against the specific device's MIB file to confirm which OIDs are actually implemented on a given ELS10 unit.

What Can Be Monitored

port bridging mode
BPDU suppression status
RIP listening status
trunk port configuration
VLAN assignment

Imported Objects

From BRIDGE-MIB

dot1dStpDesignatedRoot	OBJECT-TYPE
dot1dStpForwardDelay	OBJECT-TYPE
dot1dStpHelloTime	OBJECT-TYPE
dot1dStpMaxAge	OBJECT-TYPE
dot1dStpPortDesignatedBridge
dot1dStpPortDesignatedCost
dot1dStpPortDesignatedPort
dot1dStpPortDesignatedRoot
dot1dStpPortState
dot1dStpRootCost	OBJECT-TYPE
dot1dStpRootPort	OBJECT-TYPE

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString
PhysAddress
ifInErrors
ifOutDiscards
ifOutErrors
sysObjectID

OIDs

OID symbolic	OID numeric	Type	Access	Description
els10_27	1.3.6.1.4.1.97.9
els10_27addr	1.3.6.1.4.1.97.9.5
OCT els10_27addrBlock	1.3.6.1.4.1.97.9.5.20	OCTET STRING	read-write
INT els10_27addrBlockSize	1.3.6.1.4.1.97.9.5.19	INTEGER	read-write
GAU els10_27addrDynamicMax	1.3.6.1.4.1.97.9.5.3	Gauge	read-write
CTR els10_27addrDynamicOverflows	1.3.6.1.4.1.97.9.5.4	Counter	read-only
CTR els10_27addrDynamics	1.3.6.1.4.1.97.9.5.2	Counter	read-only
INT els10_27addrFlags	1.3.6.1.4.1.97.9.5.5	INTEGER	read-write
INT els10_27addrIndex	1.3.6.1.4.1.97.9.5.9	INTEGER	read-write
OCT els10_27addrMAC	1.3.6.1.4.1.97.9.5.6	OCTET STRING	read-write
INT els10_27addrNext	1.3.6.1.4.1.97.9.5.10	INTEGER	read-write
INT els10_27addrOperation	1.3.6.1.4.1.97.9.5.8	INTEGER	read-write
INT els10_27addrPort	1.3.6.1.4.1.97.9.5.7	INTEGER	read-write
CTR els10_27addrStatics	1.3.6.1.4.1.97.9.5.1	Counter	read-only
els10_27admin	1.3.6.1.4.1.97.9.3
OCT els10_27adminAnyPass	1.3.6.1.4.1.97.9.3.2	OCTET STRING	read-write
CTR els10_27adminArpEntries	1.3.6.1.4.1.97.9.3.11	Counter	read-only
CTR els10_27adminArpOverflows	1.3.6.1.4.1.97.9.3.13	Counter	read-only
CTR els10_27adminArpStatics	1.3.6.1.4.1.97.9.3.12	Counter	read-only
IP els10_27adminAuthenticationFailure	1.3.6.1.4.1.97.9.3.8	IpAddress	read-only
INT els10_27adminButtonSelection	1.3.6.1.4.1.97.9.3.22	INTEGER	read-write
INT els10_27adminDisableButton	1.3.6.1.4.1.97.9.3.21	INTEGER	read-write
OCT els10_27adminFatalErr	1.3.6.1.4.1.97.9.3.1	OCTET STRING	read-only	Information about last reset: First byte, cause of reset, values: 00: power failure 01: WatchDog Timeout 02: Software Reset 03: NMS Shutdown 04-255: Fatal Error Second byte, Hw/Sw component that failed Remaining bytes, description of fault.
OCT els10_27adminGetPass	1.3.6.1.4.1.97.9.3.3	OCTET STRING	read-write
CTR els10_27adminIpEntries	1.3.6.1.4.1.97.9.3.14	Counter	read-only
CTR els10_27adminIpStatics	1.3.6.1.4.1.97.9.3.15	Counter	read-only
INT els10_27adminLEDProgramOption	1.3.6.1.4.1.97.9.3.23	INTEGER	read-write
CTR els10_27adminNAMReceiveCongests	1.3.6.1.4.1.97.9.3.10	Counter	read-only
IP els10_27adminNMSIPAddr	1.3.6.1.4.1.97.9.3.4	IpAddress	read-write
INT els10_27adminRebootConfig	1.3.6.1.4.1.97.9.3.19	INTEGER	read-write
INT els10_27adminRipPreference	1.3.6.1.4.1.97.9.3.17	INTEGER	read-write
CTR els10_27adminRipRouteDiscards	1.3.6.1.4.1.97.9.3.18	Counter	read-only
INT els10_27adminStaticPreference	1.3.6.1.4.1.97.9.3.16	INTEGER	read-write
INT els10_27adminStorageFailure	1.3.6.1.4.1.97.9.3.7	INTEGER	read-only
els10_27debug	1.3.6.1.4.1.97.9.10
INT els10_27debugBase	1.3.6.1.4.1.97.9.10.3.1.3	INTEGER	read-write
OCT els10_27debugData	1.3.6.1.4.1.97.9.10.3.1.5	OCTET STRING	read-write
els10_27debugEntry	1.3.6.1.4.1.97.9.10.3.1		not-accessible
INT els10_27debugIndex	1.3.6.1.4.1.97.9.10.3.1.1	INTEGER	read-only
INT els10_27debugLength	1.3.6.1.4.1.97.9.10.3.1.4	INTEGER	read-write
INT els10_27debugOperation	1.3.6.1.4.1.97.9.10.3.1.2	INTEGER	read-write
OCT els10_27debugString	1.3.6.1.4.1.97.9.10.2	OCTET STRING	read-only
INT els10_27debugStringID	1.3.6.1.4.1.97.9.10.1	INTEGER	read-only
NTF els10_27DebugStringIdTrap	1.3.6.1.4.1.97.0.8			Sent whenever the unit has a debug text string to be displayed. The text strings are sent in a stream-like fashion.
els10_27debugTable	1.3.6.1.4.1.97.9.10.3		not-accessible
NTF els10_27DiagUnitBootedTrap	1.3.6.1.4.1.97.0.16			The unit has booted. els10-27adminFatalErr contains information about why the unit rebooted.
els10_27dot3	1.3.6.1.4.1.97.9.7
INT els10_27dot3DuplexSelection	1.3.6.1.4.1.97.9.7.1.1.14	INTEGER	read-write
els10_27dot3Entry	1.3.6.1.4.1.97.9.7.1.1		not-accessible
INT els10_27dot3Index	1.3.6.1.4.1.97.9.7.1.1.1	INTEGER	read-only
INT els10_27dot3LedOn	1.3.6.1.4.1.97.9.7.1.1.3	INTEGER	read-only
CTR els10_27dot3RxCollisions	1.3.6.1.4.1.97.9.7.1.1.4	Counter	read-only
CTR els10_27dot3RxLateColls	1.3.6.1.4.1.97.9.7.1.1.6	Counter	read-only
CTR els10_27dot3RxRunts	1.3.6.1.4.1.97.9.7.1.1.5	Counter	read-only
INT els10_27dot3SpeedSelection	1.3.6.1.4.1.97.9.7.1.1.13	INTEGER	read-write
els10_27dot3Table	1.3.6.1.4.1.97.9.7.1		not-accessible
INT els10_27dot3TPLinkOK	1.3.6.1.4.1.97.9.7.1.1.2	INTEGER	read-only
CTR els10_27dot3TxBabbles	1.3.6.1.4.1.97.9.7.1.1.8	Counter	read-only
CTR els10_27dot3TxCollisions	1.3.6.1.4.1.97.9.7.1.1.9	Counter	read-only
CTR els10_27dot3TxJabbers	1.3.6.1.4.1.97.9.7.1.1.7	Counter	read-only
INT els10_27FlowControlBackPressure	1.3.6.1.4.1.97.9.23.1	INTEGER	read-write	Control back pressure on a system wide basis. On (1), Off (2)
els10_27FlowControlCtl	1.3.6.1.4.1.97.9.23
INT els10_27FlowControlEnable	1.3.6.1.4.1.97.9.23.4.1.2	INTEGER	read-write	Control 802.3x flow control on a per interface basis. On (1), Off (2)
els10_27FlowControlEntry	1.3.6.1.4.1.97.9.23.4.1		not-accessible	Defines a particular entry containing objects pertaining to definition and control over flow control ports.
INT els10_27FlowControlInterface	1.3.6.1.4.1.97.9.23.4.1.1	INTEGER	read-only	The MIB2 interface for which this flow control information pertains
INT els10_27FlowControlPauseInteval	1.3.6.1.4.1.97.9.23.3	INTEGER	read-write	A value between 10 and 65535. Each pause interval is equal to '5.12 microseconds'. A value of 10 will equal '51.2 microseconds'.
INT els10_27FlowControlRxPauseFrames	1.3.6.1.4.1.97.9.23.4.1.3	INTEGER	read-only	The number of pause frames received on this interface.
els10_27FlowControlTable	1.3.6.1.4.1.97.9.23.4		not-accessible	Provides a list of control objects over flow control parameters.
INT els10_27FlowControlThresholdValue	1.3.6.1.4.1.97.9.23.2	INTEGER	read-write	A value specified as a percent of the available buffers. When fewer than the percent of the avaialable buffers is detected, flow control will be initiated. Flow control will cease when the free buffer count meets or exceeds this percent.
INT els10_27FlowControlTxPauseFrames	1.3.6.1.4.1.97.9.23.4.1.4	INTEGER	read-only	The number of pause frames transmitted on this interface.
els10_27hw	1.3.6.1.4.1.97.9.1
OCT els10_27hwAddr	1.3.6.1.4.1.97.9.1.4.1.5	OCTET STRING	read-only
OCT els10_27hwDiagCode	1.3.6.1.4.1.97.9.1.1	OCTET STRING	read-only
NTF els10_27hwDiagTrap	1.3.6.1.4.1.97.0.100			Sent whenever the unit's diagnostics have indicated an error.
OCT els10_27hwManufData	1.3.6.1.4.1.97.9.1.2	OCTET STRING	read-only
INT els10_27hwPortCount	1.3.6.1.4.1.97.9.1.3	INTEGER	read-only
INT els10_27hwPortDiagPassed	1.3.6.1.4.1.97.9.1.4.1.4	INTEGER	read-only
els10_27hwPortEntry	1.3.6.1.4.1.97.9.1.4.1		not-accessible
INT els10_27hwPortIndex	1.3.6.1.4.1.97.9.1.4.1.1	INTEGER	read-only
INT els10_27hwPortSubType	1.3.6.1.4.1.97.9.1.4.1.3	INTEGER	read-only
els10_27hwPortTable	1.3.6.1.4.1.97.9.1.4		not-accessible
INT els10_27hwPortType	1.3.6.1.4.1.97.9.1.4.1.2	INTEGER	read-only
INT els10_27hwUpLink	1.3.6.1.4.1.97.9.1.5	INTEGER	read-only	Specifies whether the Up-Link I/O module is existed
OCT els10_27hwUpLinkManufData	1.3.6.1.4.1.97.9.1.6	OCTET STRING	read-only	This is a 32-byte array which contains the part number, serial number, and hardware revision level of the Up-Link I/O module. This array is valid only when the els10-27hwUplink is true. If els10-27hwUplink is false, it returns an error
els10_27if	1.3.6.1.4.1.97.9.6
STR els10_27ifDescr	1.3.6.1.4.1.97.9.6.1.1.29	DisplayString	read-write
els10_27ifEntry	1.3.6.1.4.1.97.9.6.1.1		not-accessible
NTF els10_27IfErrorsTrap	1.3.6.1.4.1.97.0.21			Sent whenever the number of hardware errors in received and transmitted packets has exceeded the port's limit.
CTR els10_27ifForwardedChars	1.3.6.1.4.1.97.9.6.1.1.28	Counter	read-only
INT els10_27ifFunction	1.3.6.1.4.1.97.9.6.1.1.16	INTEGER	read-only
CTR els10_27ifGoodRxFrames	1.3.6.1.4.1.97.9.6.1.1.30	Counter	read-only
CTR els10_27ifGoodTxFrames	1.3.6.1.4.1.97.9.6.1.1.31	Counter	read-only
INT els10_27ifIndex	1.3.6.1.4.1.97.9.6.1.1.1	INTEGER	read-only
CTR els10_27ifRxHwFCSs	1.3.6.1.4.1.97.9.6.1.1.18	Counter	read-only
CTR els10_27ifRxQueues	1.3.6.1.4.1.97.9.6.1.1.19	Counter	read-only
INT els10_27ifRxQueueThresh	1.3.6.1.4.1.97.9.6.1.1.6	INTEGER	read-write
INT els10_27ifRxQueueThreshTime	1.3.6.1.4.1.97.9.6.1.1.7	INTEGER	read-write
TIK els10_27ifStatisticsTime	1.3.6.1.4.1.97.9.6.1.1.27	TimeTicks	read-only
els10_27ifTable	1.3.6.1.4.1.97.9.6.1		not-accessible
INT els10_27ifThreshold	1.3.6.1.4.1.97.9.6.1.1.4	INTEGER	read-write
INT els10_27ifThresholdTime	1.3.6.1.4.1.97.9.6.1.1.5	INTEGER	read-write
INT els10_27ifTxStormCnt	1.3.6.1.4.1.97.9.6.1.1.8	INTEGER	read-write
TIK els10_27ifTxStormTime	1.3.6.1.4.1.97.9.6.1.1.9	TimeTicks	read-write
IP els10_27igmpCacheAddress	1.3.6.1.4.1.97.9.22.5.1.1	IpAddress	read-only	The IP multicast group address for which this entry contains information.
els10_27igmpCacheEntry	1.3.6.1.4.1.97.9.22.5.1		not-accessible	An entry (conceptual row) in the els10-27igmpCacheTable.
TIK els10_27igmpCacheExpiryTime	1.3.6.1.4.1.97.9.22.5.1.3	TimeTicks	read-only	The minimum amount of time remaining before this entry will be aged out.
INT els10_27igmpCacheIfIndex	1.3.6.1.4.1.97.9.22.5.1.2	INTEGER	read-only	The interface for which this entry contains infor- mation for an IP multicast group address.
els10_27igmpCacheTable	1.3.6.1.4.1.97.9.22.5		not-accessible	The (conceptual) table listing the IP multicast groups for which there are members on a particular interface.
INT els10_27igmpPortDelay	1.3.6.1.4.1.97.9.22.4	INTEGER	read-write	Timeout value (mins) between IGMP Reports or IGMP Queries received on a port before the system times out the entry from the Multicast Address Filter (default is 5 minutes).
INT els10_27igmpQueryCount	1.3.6.1.4.1.97.9.22.3	INTEGER	read-write	Maximum number of queries that have not been heard on the system before the system starts taking action to solicit reports (default is 5).
INT els10_27igmpQueryStatus	1.3.6.1.4.1.97.9.22.2	INTEGER	read-write	Parameter to enable or disable the device to act as a Querier. If enabled, the device will send out a Query as a Proxy to solicit reports. The device will not become an IGMP router. The default is disabled.
INT els10_27igmpStatus	1.3.6.1.4.1.97.9.22.1	INTEGER	read-write	Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports. The default is enabled.
NTF els10_27InvalidConfigurationFileTrap	1.3.6.1.4.1.97.0.34			Diagnostics has detected corrupted configuration data. Default parameter values have been restored.
INT els10_27ipmInterfaceRtr	1.3.6.1.4.1.97.9.21.2	INTEGER	read-write	Parameter to enable or disable the inclusion of this interface in all Multicast filters. When enabled, all IP Multicast packets for all group filters will be transmitted over this interface. Value is a bit mask.
INT els10_27IPMulticastStatus	1.3.6.1.4.1.97.9.21.1	INTEGER	read-write	Parameter to enable or disable IP multicast filtering on the device. When enabled, the device will examine IP Multicast data packets and dynamically set up filter ports to prevent flooding. The default is disabled.
els10_27lpbk	1.3.6.1.4.1.97.9.11
OCT els10_27lpbkDestAddr	1.3.6.1.4.1.97.9.11.1.1.3	OCTET STRING	read-write
els10_27lpbkEntry	1.3.6.1.4.1.97.9.11.1.1		not-accessible
CTR els10_27lpbkErrorBadReceives	1.3.6.1.4.1.97.9.11.1.1.10	Counter	read-only
CTR els10_27lpbkErrorNoReceives	1.3.6.1.4.1.97.9.11.1.1.9	Counter	read-only
INT els10_27lpbkErrorOffset	1.3.6.1.4.1.97.9.11.1.1.14	INTEGER	read-only
OCT els10_27lpbkErrorReceived	1.3.6.1.4.1.97.9.11.1.1.13	OCTET STRING	read-only
OCT els10_27lpbkErrorSent	1.3.6.1.4.1.97.9.11.1.1.12	OCTET STRING	read-only
INT els10_27lpbkErrorSize	1.3.6.1.4.1.97.9.11.1.1.11	INTEGER	read-only
CTR els10_27lpbkGoods	1.3.6.1.4.1.97.9.11.1.1.8	Counter	read-only
INT els10_27lpbkIncrements	1.3.6.1.4.1.97.9.11.1.1.7	INTEGER	read-write
INT els10_27lpbkIndex	1.3.6.1.4.1.97.9.11.1.1.1	INTEGER	read-only
TIK els10_27lpbkInterval	1.3.6.1.4.1.97.9.11.1.1.5	TimeTicks	read-write
INT els10_27lpbkOperation	1.3.6.1.4.1.97.9.11.1.1.2	INTEGER	read-write
NTF els10_27LpbkOperationTrap	1.3.6.1.4.1.97.0.9			Send whenever the unit has finished a loop back test, or a loop back error has been detected.
INT els10_27lpbkPktLength	1.3.6.1.4.1.97.9.11.1.1.6	INTEGER	read-write
INT els10_27lpbkPktNum	1.3.6.1.4.1.97.9.11.1.1.4	INTEGER	read-write
els10_27lpbkTable	1.3.6.1.4.1.97.9.11.1		not-accessible
TIK els10_27pingAvg	1.3.6.1.4.1.97.9.16.2.1.11	TimeTicks	read-only	The average round trip time for the ping requests and responses, in centiseconds.
INT els10_27pingCount	1.3.6.1.4.1.97.9.16.2.1.4	INTEGER	read-write	The number of ping requests which are to be sent. This variable cannot be set while els10-27pingOperation is on.
INT els10_27pingDataSize	1.3.6.1.4.1.97.9.16.2.1.5	INTEGER	read-write	The datagram packet size which will be sent with the ECHO_REQUEST, in bytes. This variable cannot be set while els10-27pingOperation is on.
TIK els10_27pingDataTimeout	1.3.6.1.4.1.97.9.16.1	TimeTicks	read-write	The time, in centiseconds, from the last ping activity (a send or receive of an ECHO_RESPONSE or ECHO_REQUEST message), to when the els10-27pingEntry information for that ping request will be deleted.
IP els10_27pingDestAddr	1.3.6.1.4.1.97.9.16.2.1.2	IpAddress	read-write	The IP address which is to be the destination of the ping ECHO_REQUEST. This variable cannot be set while els10-27pingOperation is on.
els10_27pingEntry	1.3.6.1.4.1.97.9.16.2.1		not-accessible	The parameters, state, and results of a ping request.
TIK els10_27pingMax	1.3.6.1.4.1.97.9.16.2.1.10	TimeTicks	read-only	The maximum round trip for the ping requests and responses, in centiseconds.
els10_27pingMgt	1.3.6.1.4.1.97.9.16
TIK els10_27pingMin	1.3.6.1.4.1.97.9.16.2.1.9	TimeTicks	read-only	The minimum round trip time for the ping requests and responses, in centiseconds.
IP els10_27pingNMSAddr	1.3.6.1.4.1.97.9.16.2.1.1	IpAddress	read-only	The IP address of the NMS, used to determine which ping request to return information on.
INT els10_27pingNumReceived	1.3.6.1.4.1.97.9.16.2.1.13	INTEGER	read-only	The number of ICMP ECHO_RESPONSE messages that have been received as a result of this ping request.
INT els10_27pingNumTransmitted	1.3.6.1.4.1.97.9.16.2.1.12	INTEGER	read-only	The number of ICMP ECHO_REQUEST messages that have been transmitted during this ping request.
INT els10_27pingOperation	1.3.6.1.4.1.97.9.16.2.1.8	INTEGER	read-write	Setting els10-27pingOperation to on will begin the ping request. Setting els10-27pingOperation to off will terminate the ping request.
INT els10_27pingState	1.3.6.1.4.1.97.9.16.2.1.3	INTEGER	read-only	The current state of the ping request.
els10_27pingTable	1.3.6.1.4.1.97.9.16.2		not-accessible	The set of information describing the active ping requests and their results.
TIK els10_27pingTimeOut	1.3.6.1.4.1.97.9.16.2.1.7	TimeTicks	read-write	The time, in centiseconds, since the last ECHO_RESPONSE was received (or the last ECHO_REQUEST was sent, if there have been no responses) when the ping request will time out. This variable cannot be set while els10-27pingOperation is on.
TIK els10_27pingWait	1.3.6.1.4.1.97.9.16.2.1.6	TimeTicks	read-write	The time, in centiseconds, between the sending of each ECHO_REQUEST message. This variable cannot be set while els10-27pingOperation is on.
NTF els10_27PortCongestedTrap	1.3.6.1.4.1.97.0.18			Sent whenever outbound congestion control has been invoked for the port.
NTF els10_27PortFunctionsTrap	1.3.6.1.4.1.97.0.3			Sent whenever the current functional state (active protocols) of the port has changed.
els10_27proto	1.3.6.1.4.1.97.9.12
INT els10_27protoBridge	1.3.6.1.4.1.97.9.12.1.1.2	INTEGER	read-write	Defines the bridging method to be applied to frames received at, or destined for, this port. Ethernet and FDDI ports may be configured for transparent, srt, or none. Token Ring ports may be configured for any of the four options. The UART may only be configured to none.
els10_27protoEntry	1.3.6.1.4.1.97.9.12.1.1		not-accessible	Each entry in this table specifies which protocols are used by a particular port in the ES/1.
INT els10_27protoIfIndex	1.3.6.1.4.1.97.9.12.1.1.1	INTEGER	read-only	Identifies the interface (port) to which this entry's information belongs. The value of this variable corresponds to ifIndex, as well as most of the other port identification values in related MIBs.
INT els10_27protoRipListen	1.3.6.1.4.1.97.9.12.1.1.4	INTEGER	read-write	Specifies whether the port should listen for internet Routing Information Protocol (RFC-1058) packets, in order to build the routing table for the unit.
INT els10_27protoSuppressBpdu	1.3.6.1.4.1.97.9.12.1.1.3	INTEGER	read-write	Allows transmission of spanning tree protocol packets to be suppressed. If normal(1), 802.1d spanning tree packets are transmitted as usual. If suppressed(2), these packets are not transmitted. This option may be needed for in- teroperability with non-802.1d spanning tree protocols (e.g., DEC LanBridge 100).
els10_27protoTable	1.3.6.1.4.1.97.9.12.1		not-accessible	This table contains configuration information specify- ing the types of protocols used to bridge, route, translate, and filter frames for each port.
INT els10_27protoTrunking	1.3.6.1.4.1.97.9.12.1.1.5	INTEGER	read-write	Specifies whether SMC's trunking protocol (an extension to the standard Spanning Tree) is to be used over this port.
NTF els10_27RxQueuesTrap	1.3.6.1.4.1.97.0.4			Sent whenever the number of times that the port's receiver has stopped receiving packets due to buffer space shortages has exceeded the port's limit.
NTF els10_27RxStormFlagTrap	1.3.6.1.4.1.97.0.5			Sent whenever broadcast/multicast storm protection has been invoked for the port.
INT els10_27sprotoTransmitPacing	1.3.6.1.4.1.97.9.12.1.1.6	INTEGER	read-write	When enabled, introduces delays into normal transmission of frames, to reduce the probability of collisions during heavy traffic.
NTF els10_27StDesigRootTrap	1.3.6.1.4.1.97.0.28			The Root Bridge ID in received Spanning Tree Configuration BPDUs from the port has changed.
NTF els10_27StForwardDelayTrap	1.3.6.1.4.1.97.0.27			The unit's spanning tree forward delay time has changed.
NTF els10_27StHelloTimeTrap	1.3.6.1.4.1.97.0.26			The unit's spanning tree hello time has changed.
NTF els10_27StInvalidFlashCodeImageTrap	1.3.6.1.4.1.97.0.35			An invalid code image was detected in flash memory. An attempt will be made to obtain a valid image.
NTF els10_27StMaxAgeTrap	1.3.6.1.4.1.97.0.25			The unit's spanning tree maximum age has changed.
NTF els10_27StorageFailureTrap	1.3.6.1.4.1.97.0.17			Sent if the unit's Configuration EEPROM has failed. The unit will not be able to reboot, and must be returned to the factory.
NTF els10_27StPortDesigBridgeTrap	1.3.6.1.4.1.97.0.29			The bridge ID of the spanning tree designated bridge of the LAN/WAN to which the port is attached has changed.
NTF els10_27StPortDesigCostTrap	1.3.6.1.4.1.97.0.30			The cost to the spanning tree root bridge from the designated port of the LAN/WAN to which the port is attached has changed.
NTF els10_27StPortDesigPortTrap	1.3.6.1.4.1.97.0.31			The port ID of the spanning tree designated port of the LAN/WAN to which the port is attached has changed.
NTF els10_27StPortStateTrap	1.3.6.1.4.1.97.0.32			The spanning tree state of the port has changed.
NTF els10_27StRootCostTrap	1.3.6.1.4.1.97.0.23			The unit's spanning tree cost to the root bridge has changed.
NTF els10_27StRootIDTrap	1.3.6.1.4.1.97.0.22			The spanning tree root bridge ID for the unit has changed.
NTF els10_27StRootPortTrap	1.3.6.1.4.1.97.0.24			The unit's spanning tree root port has changed.
els10_27sw	1.3.6.1.4.1.97.9.2
OCT els10_27swBases	1.3.6.1.4.1.97.9.2.2.1.7	OCTET STRING	read-only
INT els10_27swCount	1.3.6.1.4.1.97.9.2.2.1.3	INTEGER	read-only
STR els10_27swDesc	1.3.6.1.4.1.97.9.2.2.1.2	DisplayString	read-only
els10_27swdis	1.3.6.1.4.1.97.9.4
INT els10_27swdisAccess	1.3.6.1.4.1.97.9.4.2	INTEGER	read-write	The version of software that may be downloaded. Attempts to download other versions of software will be rejected. The value for swdisAccess is embedded within the software files that are to be distributed via TFTP. Its value may be derived from the names of the software files. the NMS operator may wish to use the following special values: protected (1) No software downloads will be accepted any-software (2) A software download of any version of new software will be accepted - this is the factory default
IP els10_27swdisConfigIp	1.3.6.1.4.1.97.9.4.4	IpAddress	read-write	The IP address of the NMS (i.e., any IP host) that is allowed to use TFTP to send/retrieve the configuration file of the FN1026. A value of 0.0.0.0 (which is the factory specified default) prevents any NMS from obtaining access, while a value of 255.255.255.255 gives every NMS permission.
INT els10_27swdisConfigRetryTime	1.3.6.1.4.1.97.9.4.5	INTEGER	read-write	The number of seconds that the FN1026 will wait for an acknowledgment before it retransmits an unacknowledged TFTP data block. The factory specified default is 5 seconds.
INT els10_27swdisConfigTotalTimeout	1.3.6.1.4.1.97.9.4.6	INTEGER	read-write	The number of seconds that the FN1026 will wait for an acknowledgment to a data block before it cancels a TFTP session. The factory specified default is 25 seconds.
OCT els10_27swdisDesc	1.3.6.1.4.1.97.9.4.1	OCTET STRING	read-only	The description (0-32 bytes) of the software set currently being downloaded, or a description of the software set last downloaded since the FN1026 booted.
INT els10_27swdisWriteStatus	1.3.6.1.4.1.97.9.4.3	INTEGER	read-only	The status of the erase/write operation.
els10_27swFilesetEntry	1.3.6.1.4.1.97.9.2.2.1		not-accessible
els10_27swFilesetTable	1.3.6.1.4.1.97.9.2.2		not-accessible
INT els10_27swFlashBank	1.3.6.1.4.1.97.9.2.2.1.8	INTEGER	read-only
INT els10_27swIndex	1.3.6.1.4.1.97.9.2.2.1.1	INTEGER	read-only
INT els10_27swNumber	1.3.6.1.4.1.97.9.2.1	INTEGER	read-only
OCT els10_27swSizes	1.3.6.1.4.1.97.9.2.2.1.5	OCTET STRING	read-only
OCT els10_27swStarts	1.3.6.1.4.1.97.9.2.2.1.6	OCTET STRING	read-only
OCT els10_27swType	1.3.6.1.4.1.97.9.2.2.1.4	OCTET STRING	read-only
NTF els10_27TopChangeBegunTrap	1.3.6.1.4.1.97.0.19			The spanning tree topology has begun to change.
NTF els10_27TopChangeEndTrap	1.3.6.1.4.1.97.0.20			The spanning tree topology has stopped changing.
INT els10_27traceDataSize	1.3.6.1.4.1.97.9.17.2.1.4	INTEGER	read-write	The size of the datagram sent with each probe. This variable cannot be set while els10-27traceOperation is on.
TIK els10_27traceDataTimeout	1.3.6.1.4.1.97.9.17.1	TimeTicks	read-write	The time, in centiseconds, from the last traceroute activity (the response to or timeout of the last probe sent), to when the els10-27traceEntry information for that traceroute request will be deleted.
IP els10_27traceDestAddr	1.3.6.1.4.1.97.9.17.2.1.2	IpAddress	read-write	The IP address which is to be the destination of the traceroute request.This variable cannot be set while els10-27traceOperation is on.
els10_27traceEntry	1.3.6.1.4.1.97.9.17.2.1		not-accessible	The parameters, state, and results of a traceroute request.
INT els10_27traceHop	1.3.6.1.4.1.97.9.17.2.1.8	INTEGER	read-only	The hop count for a set of probes with a particular TTL.
IP els10_27traceHopAddr	1.3.6.1.4.1.97.9.17.2.1.9	IpAddress	read-only	The IP address of the host which responded for a probe with a particular TTL.
INT els10_27traceMaxTTL	1.3.6.1.4.1.97.9.17.2.1.3	INTEGER	read-write	The maximum time-to-live for outgoing traceroute probe packets. This determines the number of hops that can be in a traceroute. This variable cannot be set while els10-27traceOperation is on.
els10_27traceMgt	1.3.6.1.4.1.97.9.17
IP els10_27traceNMSAddr	1.3.6.1.4.1.97.9.17.2.1.1	IpAddress	read-only	The IP address of the NMS, used to determine which traceroute request to return information on.
INT els10_27traceNumProbes	1.3.6.1.4.1.97.9.17.2.1.5	INTEGER	read-write	The number of probes which are sent for each hop. This variable cannot be set while els10-27traceOperation is on.
INT els10_27traceOperation	1.3.6.1.4.1.97.9.17.2.1.7	INTEGER	read-write	Setting els10-27traceOperation to on will begin the traceroute request. Setting els10-27traceOperation to off will terminate the traceroute request.
INT els10_27traceProbe	1.3.6.1.4.1.97.9.17.2.1.10	INTEGER	read-only	The probe instance for a particular hop.
INT els10_27traceState	1.3.6.1.4.1.97.9.17.2.1.11	INTEGER	read-only	The current state of the trace probe.
els10_27traceTable	1.3.6.1.4.1.97.9.17.2		not-accessible	The set of information describing the active traceroute requests and their results.
TIK els10_27traceTime	1.3.6.1.4.1.97.9.17.2.1.12	TimeTicks	read-only	Round trip time of a probe for a particular hop.
TIK els10_27traceWait	1.3.6.1.4.1.97.9.17.2.1.6	TimeTicks	read-write	The time to wait in response to a probe. This variable cannot be set while els10-27traceOperation is on.
els10_27trapControlEntry	1.3.6.1.4.1.97.9.15.1.1		not-accessible
els10_27trapControlTable	1.3.6.1.4.1.97.9.15.1		not-accessible	This table contains information about the severity of each trap and whether the trap is currently enabled.
INT els10_27trapEnabled	1.3.6.1.4.1.97.9.15.1.1.2	INTEGER	read-write	Enable or disable the generation of this trap.
els10_27trapEntry	1.3.6.1.4.1.97.9.15.7.1		not-accessible
INT els10_27trapEntryIndex	1.3.6.1.4.1.97.9.15.7.1.1	INTEGER	read-only	A number representing the order in which the trap occurred in time. This 32 bit number can wrap.
INT els10_27trapEntryNumber	1.3.6.1.4.1.97.9.15.7.1.4	INTEGER	read-only	The specific trap number, as specified in the TRAP PDU.
INT els10_27trapEntrySeverity	1.3.6.1.4.1.97.9.15.7.1.5	INTEGER	read-only	A user-definable severity, indicating the importance of the trap.
STR els10_27trapEntryText	1.3.6.1.4.1.97.9.15.7.1.3	DisplayString	read-only	A description of the trap.
TIK els10_27trapEntryTimeStamp	1.3.6.1.4.1.97.9.15.7.1.2	TimeTicks	read-only	The time at which the trap occurred.
INT els10_27trapIncludeText	1.3.6.1.4.1.97.9.15.3	INTEGER	read-write	Whether or not a formatted text string is included in the trap PDU.
INT els10_27trapIndex	1.3.6.1.4.1.97.9.15.1.1.1	INTEGER	read-only	The specific trap number.
els10_27trapMgt	1.3.6.1.4.1.97.9.15
INT els10_27trapNumber	1.3.6.1.4.1.97.9.15.6	INTEGER	read-only	The number of traps that are in the els10-27trapTable.
INT els10_27trapRetry	1.3.6.1.4.1.97.9.15.5	INTEGER	read-write	The number of times any enterprise-specific trap is to be sent for a given event. PDUs are retried using a truncated exponential backoff: 2 seconds, 4 seoncs, 8 seconds, 16 seconds, and then 32 seconds for all succeeding intervals.
INT els10_27trapSeverity	1.3.6.1.4.1.97.9.15.1.1.3	INTEGER	read-write	A user-definable severity, indicating the importance of the trap.
els10_27trapSeverityControlEntry	1.3.6.1.4.1.97.9.15.2.1		not-accessible
INT els10_27trapSeverityControlSeverity	1.3.6.1.4.1.97.9.15.2.1.1	INTEGER	read-write	A user-definable severity, indicating the importance of the trap.
els10_27trapSeverityControlTable	1.3.6.1.4.1.97.9.15.2		not-accessible	This table contains information about whether a class of traps of a particular severity are enabled or disabled.
INT els10_27trapSeverityEnable	1.3.6.1.4.1.97.9.15.2.1.2	INTEGER	read-write	Enable or disable all traps of a given severity level.
els10_27trapTable	1.3.6.1.4.1.97.9.15.7		not-accessible	This table contains the latest traps that have been generated.
STR els10_27trapText	1.3.6.1.4.1.97.9.15.1.1.4	DisplayString	read-only	A description of the trap.
TIK els10_27trapTime	1.3.6.1.4.1.97.9.15.4	TimeTicks	read-write	The time, in centiseconds, which should expire between the sending of traps.
els10_27trunk	1.3.6.1.4.1.97.9.13
NTF els10_27TrunkBridgeAddrTrap	1.3.6.1.4.1.97.0.11			The associated trunking MAC address of the bridge ID of the remote bridge has changed.
els10_27trunkEntry	1.3.6.1.4.1.97.9.13.1.1		not-accessible	An entry exists in this table for each physical interface (port) that is configured for trunking.
NTF els10_27TrunkErrorTrap	1.3.6.1.4.1.97.0.13			An error has occurred in trunking.
INT els10_27trunkIfIndex	1.3.6.1.4.1.97.9.13.1.1.1	INTEGER	read-only	Identifies a physical interface (port) which is configured for LAN trunking. The value of this variable corresponds to ifIndex, as well as most of the other port identification values in related MIBs.
NTF els10_27TrunkIPAddrTrap	1.3.6.1.4.1.97.0.12			The associated trunking IP address of the remote bridge has changed.
INT els10_27trunkLastChange	1.3.6.1.4.1.97.9.13.1.1.8	INTEGER	read-only	The number of seconds since els10-27trunkState changed.
INT els10_27trunkLastError	1.3.6.1.4.1.97.9.13.1.1.5	INTEGER	read-only	The last reason for failure when the link is in closed, oneway, or helddown state.
INT els10_27trunkLinkCount	1.3.6.1.4.1.97.9.13.1.1.7	INTEGER	read-only	The number of links within the trunk group.
NTF els10_27TrunkLinkCountTrap	1.3.6.1.4.1.97.0.15			The number of ports in the trunking group has changed.
INT els10_27trunkLinkOrdinal	1.3.6.1.4.1.97.9.13.1.1.6	INTEGER	read-only	The position of this link within the trunk group.
NTF els10_27TrunkLinkOrdinalTrap	1.3.6.1.4.1.97.0.14			The port's index in the trunking group has changed.
OCT els10_27trunkRemoteBridgeAddr	1.3.6.1.4.1.97.9.13.1.1.3	OCTET STRING	read-only	The MAC address portion of the bridge ID of the remote bridge.
IP els10_27trunkRemoteIp	1.3.6.1.4.1.97.9.13.1.1.4	IpAddress	read-only	The IP address of the remote bridge, as reported by that bridge for administrative purposes.
INT els10_27trunkState	1.3.6.1.4.1.97.9.13.1.1.2	INTEGER	read-only	If off(1) then this link has not been enabled for trunking. If closed(2) then this link has not yet received any Trunking PDUs. If oneway(3) then incoming Trunking PDUs do not indicate that our PDUs are being successfully received by the far end. If joined(4) then this link is actively participating in the trunk group. If perturbed(5) then this link is actively participating in the trunk group; however, the transmission of data packets has been temporarily stopped due to a change in membership of the group. If helddown(6) then an error has been detected and the link is being held out-of-service until the error clears. If broken(7) then this link has been configured for trunking, but the port is physically non-operational.
NTF els10_27TrunkStateTrap	1.3.6.1.4.1.97.0.10			A trunking state change transition has occurred. The possible transitions are: CLOSED-ONEWAY ONEWAY-PERTURBED PERTURBED-JOINED JOINED-HELDDOWN CLOSED-HELDDOWN ONEWAY-HELDDOWN PERTURBED-HELDDOWN
els10_27trunkTable	1.3.6.1.4.1.97.9.13.1		not-accessible	This table describes the trunking status and attributes of the interfaces that are configured for bridge trunking.
NTF els10_27TxCongestsTrap	1.3.6.1.4.1.97.0.6			Sent whenever packets destined for the unit itself were discarded due to lack of buffer space.
els10_27uart	1.3.6.1.4.1.97.9.8
CTR els10_27uartAlignmentErrors	1.3.6.1.4.1.97.9.8.1.1.3	Counter	read-only
INT els10_27uartBaud	1.3.6.1.4.1.97.9.8.1.1.2	INTEGER	read-write
els10_27uartEntry	1.3.6.1.4.1.97.9.8.1.1		not-accessible
INT els10_27uartIndex	1.3.6.1.4.1.97.9.8.1.1.1	INTEGER	read-only
CTR els10_27uartOverrunErrors	1.3.6.1.4.1.97.9.8.1.1.4	Counter	read-only
els10_27uartTable	1.3.6.1.4.1.97.9.8.1		not-accessible
INT els10_27VlanAccessList	1.3.6.1.4.1.97.9.20.5	INTEGER	read-write	A list of ports that should act as 'Access Ports'. These ports will strip all tags on egress and also make use of a shared database that will automatically be kept by the firmware. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the next octet specifying ports 9 through 16, etc. Within each octet, the least significant bit represents the lowest numbered port, and the most significant bit represents the highest numbered port. Thus, each port of the VLAN bridge is represented by single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'
els10_27VlanBridgeConfig	1.3.6.1.4.1.97.9.20
els10_27VlanConfigEgressEntry	1.3.6.1.4.1.97.9.20.6.5.1		not-accessible	Allows for configuration of specific VLAN entries.
els10_27VlanConfigEgressTable	1.3.6.1.4.1.97.9.20.6.5		not-accessible	This table allows for the specifying of the default VLAN ID for a specific port. If NOT configured as an 'Access' port, then packets containing this VLAN ID will have the tag stripped on egress. This will set the PVID for each port contained within the list.
els10_27VlanConfigEntry	1.3.6.1.4.1.97.9.20.6.4.1		not-accessible	Allows for configuration of specific VLAN entries.
INT els10_27VlanConfigEstablish	1.3.6.1.4.1.97.9.20.6.4.1.8	INTEGER	read-write	A set of the value create(1), causes an entry to be created in the els10-27VlanConfigTable as specified by the instancing information of els10-27VlanConfigVID, els10-27VlanConfigName, and els10-27VlanConfigPorts. A set of delete(2) causes the specified entry to be removed from the table. A read of this object will always return create(1).
INT els10_27VlanConfigIndex	1.3.6.1.4.1.97.9.20.6.4.1.1	INTEGER	read-write	The interface being configured.
INT els10_27VlanConfigIP	1.3.6.1.4.1.97.9.20.6.4.1.4	INTEGER	read-write	The IP address to be used to access the unit on this Vlan. This must be a valid host address.
INT els10_27VlanConfigIPMask	1.3.6.1.4.1.97.9.20.6.4.1.5	INTEGER	read-write	The IP subnet mask to be used with this Ip address.
STR els10_27VlanConfigName	1.3.6.1.4.1.97.9.20.6.4.1.6	DisplayString	read-write	The ASCII name associated with the configured VLAN. A set of this object prior to creating an entry by setting els10-27VlanEstablish will fail with a NO-INSTANCE error.
INT els10_27VlanConfigPorts	1.3.6.1.4.1.97.9.20.6.4.1.3	INTEGER	read-write	Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the next octet specifying ports 9 through 16, etc. Within each octet, the least significant bit represents the lowest numbered port, and the most significant bit represents the highest numbered port. Thus, each port of the VLAN bridge is represented by single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
INT els10_27VlanConfigStatus	1.3.6.1.4.1.97.9.20.6.4.1.7	INTEGER	read-write	A set with the value of enable(1), enables all associated entries in els10-27VlanConfigVID table for the specified VLAN. A set of disable(2), disables all els10-27VlanConfigVID entries associated with the specified VLAN. A set of this object prior to creating an entry by setting els10-27VlanConfigEstablish will fail with a NO-INSTANCE error.
els10_27VlanConfigTable	1.3.6.1.4.1.97.9.20.6.4		not-accessible	This table allows for the creation, deletion, and modification of specific VLANs. The ports defined within this group will be members of the 'member set' as defined in the IEEE 802.1Q specification.
INT els10_27VlanConfigVID	1.3.6.1.4.1.97.9.20.6.4.1.2	INTEGER	read-write	The 12 bit VLAN Identifier associated with the configured VLAN.
els10_27VlanConfigVlan	1.3.6.1.4.1.97.9.20.6
INT els10_27VlanEgressIndex	1.3.6.1.4.1.97.9.20.6.5.1.1	INTEGER	read-write	The index into the Vlan table. A port must be a member of this Vlan prior to assigning this Id as the default.
INT els10_27VlanEgressList	1.3.6.1.4.1.97.9.20.6.5.1.3	INTEGER	read-write	The set of ports to which traffic destined for the VLAN specified by els10-27VlanEgressVID on the device will have this tag stripped on egress. Each octet within the value of this object specifies a set of eight ports, with thee first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the least significant bit represents the lowest numbered port, and the most significant bit represents the highest numbered port. Thus, each port of the VLAN bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
INT els10_27VlanEgressStatus	1.3.6.1.4.1.97.9.20.6.5.1.4	INTEGER	read-write	A set with the value of enable(1), enables all associated entries in els10-27VlanEgressVID table for the specified VLAN. A set of disable(2), disables all els10-27VlanEgressVID entries associated with the specified VLAN. A set of this object prior to creating an entry by setting els10-27VlanEgressEstablish will fail with a NO-INSTANCE error.
INT els10_27VlanEgressVID	1.3.6.1.4.1.97.9.20.6.5.1.2	INTEGER	read-write	The 12 bit VLAN Identifier associated with the configured VLAN.
els10_27VlanFilterGVRPEntry	1.3.6.1.4.1.97.9.20.6.6.1		not-accessible	Allows for configuration of specific entries.
INT els10_27VlanFilterGVRPEstablishVID	1.3.6.1.4.1.97.9.20.6.6.1.5	INTEGER	read-write	A set of the value create(1), causes an entry to be created in the els10-27VlanFilterGVRPTable as specified by the instancing information of els10-27VlanFilterGVRpVID, and els10-27VlanFilterGVRPPorts. A set of delete(2) causes the specified entry to be removed from the table. A read of this object will always return create(1).
INT els10_27VlanFilterGVRPIndex	1.3.6.1.4.1.97.9.20.6.6.1.1	INTEGER	read-write	The index into the Vlan Filter table. A maximum of 32 Vlan ID can be restricted from being learnt via GVRP.
INT els10_27VlanFilterGVRPList	1.3.6.1.4.1.97.9.20.6.6.1.3	INTEGER	read-write	The set of ports that will be restricted from leaning of a VLAN ID from a GVRP message. The VLAN ID is specified by els10-27VlanFilterGVRPVID. Each octet within the value of this object specifies a set of eight ports, with thee first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the least significant bit represents the lowest numbered port, and the most significant bit represents the highest numbered port. Thus, each port of the VLAN bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
INT els10_27VlanFilterGVRPStatus	1.3.6.1.4.1.97.9.20.6.6.1.4	INTEGER	read-write	A set with the value of enable(1), enables all associated entries in els10-27VlanFilterGVRPVID table for the specified VLAN. A set of disable(2), disables all els10-27VlanFilterGVRPVID entries associated with the specified VLAN. A set of this object prior to creating an entry by setting els10-27VlanConfigEstablish will fail with a NO-INSTANCE error.
els10_27VlanFilterGVRPTable	1.3.6.1.4.1.97.9.20.6.6		not-accessible	This table allows for the specifying of VLAN ID's that will be resticted from being learnt by the device. If a GVRP packet is received specifying this VLAN ID, it will be ignored.
INT els10_27VlanFilterGVRPVID	1.3.6.1.4.1.97.9.20.6.6.1.2	INTEGER	read-write	The 12 bit VLAN Identifier associated with the configured VLAN.
INT els10_27VlanGVRPEnable	1.3.6.1.4.1.97.9.20.4	INTEGER	read-write	If the switch is operating in 802.1Q mode, this selects whether GVRP protocol messages should be processed and VLANs configured accordingly for each port on the switch. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the next octet specifying ports 9 through 16, etc. Within each octet, the least significant bit represents the lowest numbered port, and the most significant bit represents the highest numbered port. Thus, each port of the VLAN bridge is represented by single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'
INT els10_27VlanMaxNumEntries	1.3.6.1.4.1.97.9.20.6.3	INTEGER	read-only	The maximum number of VLAN entries for the device.
INT els10_27VlanNumActiveEntries	1.3.6.1.4.1.97.9.20.6.1	INTEGER	read-only	The number of active VLAN entries for the device. This includes both static and dynamic VLANs.
INT els10_27VlanNumConfiguredEntries	1.3.6.1.4.1.97.9.20.6.2	INTEGER	read-only	The number of configured VLAN entries for the device.
INT els10_27VlanOperatingMode	1.3.6.1.4.1.97.9.20.2	INTEGER	read-write	Selects the mode of operation. The switch can operate as simply an 802.1d switch, or an 802.1d switch with IEEE VLAN capability (802.1Q). A read of this object will return the current operating mode.
INT els10_27VlanResetDefaults	1.3.6.1.4.1.97.9.20.3	INTEGER	read-write	To reset the specified bridge. The filtering database is cleared and initialized with the entries specified in the Permananent database, and the Bridge protocol Entity is initialized. While initializing a read will return a value of reset (2). While operational a read will return a value of operating (2).
els10_27VlanStaticEntry	1.3.6.1.4.1.97.9.20.6.7.1		not-accessible	Allows for specifying specific entries.
INT els10_27VlanStaticEstablish	1.3.6.1.4.1.97.9.20.6.7.1.4	INTEGER	read-write	A set of the value create(1), causes an entry to be created as specified by the instancing information of els10-27VlanSaticVID, els10-27VlanStaticMAC, and els10-27VlanStaticPorts. A set of delete(2) causes the specified entry to be removed from thetable. A read of this object will always return create(1).
PHY els10_27VlanStaticMAC	1.3.6.1.4.1.97.9.20.6.7.1.2	PhysAddress	read-write	The media dependent physical address.
INT els10_27VlanStaticPort	1.3.6.1.4.1.97.9.20.6.7.1.3	INTEGER	read-write	An integer designating the port number to associate this address to.
els10_27VlanStaticTable	1.3.6.1.4.1.97.9.20.6.7		not-accessible	Allows for configuration of specific VLAN/MAC Address entries and to specify the port to which traffic destined for this address pair should be forwarded. These entries will not be aged out of the forwarding data base.
INT els10_27VlanStaticVID	1.3.6.1.4.1.97.9.20.6.7.1.1	INTEGER	read-write	The 12 bit VLAN Identifier associated with the configured VLAN.
INT els10_27VlanVersionNumber	1.3.6.1.4.1.97.9.20.1	INTEGER	read-only	Specifies the version IEEE 802.1Q VLAN that has been implemented to.
els10_27voligmpgroup	1.3.6.1.4.1.97.9.22
els10_27volipmgroup	1.3.6.1.4.1.97.9.21
els10_27volmirrorgroup	1.3.6.1.4.1.97.9.19
INT els10_27volmirrorIndex	1.3.6.1.4.1.97.9.19.4.1.1	INTEGER	read-only	Entry Index
OCT els10_27volmirrorMac1	1.3.6.1.4.1.97.9.19.4.1.2	OCTET STRING	read-write	First MAC address for mirroring.
els10_27volmirrorMacEntry	1.3.6.1.4.1.97.9.19.4.1		not-accessible	Information about specific unicast MAC addresses for which mirroring will act upon.
els10_27volMirrorMacTable	1.3.6.1.4.1.97.9.19.4		not-accessible	A table that contains information for the mirroring on MAC addresses.
INT els10_27volmirrorMode	1.3.6.1.4.1.97.9.19.1	INTEGER	read-write	To turn port mirroring on or off.
INT els10_27volmirrorPort	1.3.6.1.4.1.97.9.19.2	INTEGER	read-write	The number of the port whose data will be mirrored to a special monitor or analyzer port.
INT els10_27volmonitorPort	1.3.6.1.4.1.97.9.19.3	INTEGER	read-write	Identifies the monitor or analyzer port to receive frames from the special mirror port.
els10_27workgroup	1.3.6.1.4.1.97.9.14
INT els10_27WorkGroupCurrentCount	1.3.6.1.4.1.97.9.14.2	INTEGER	read-only	The total number of workgroups currently defined.
els10_27WorkGroupEntry	1.3.6.1.4.1.97.9.14.4.1		not-accessible	Each entry in this table contains a definition of a work group.
INT els10_27WorkGroupMaxCount	1.3.6.1.4.1.97.9.14.3	INTEGER	read-only	The maximum number of workgroups allowed.
STR els10_27WorkGroupName	1.3.6.1.4.1.97.9.14.4.1.2	DisplayString	read-write	A 1-16 character work group name.
INT els10_27WorkGroupNextNumber	1.3.6.1.4.1.97.9.14.1	INTEGER	read-only	The next available workgroup number to be used. When creating a new workgroup, it is recommended to read the value of the variable and use it to key into the workgroup table.
INT els10_27WorkGroupNumber	1.3.6.1.4.1.97.9.14.4.1.1	INTEGER	read-write	An integer that identifies the work group, used as an index to this table.
OCT els10_27WorkGroupPorts	1.3.6.1.4.1.97.9.14.4.1.3	OCTET STRING	read-write	A list of all ports within the group. The first octet specified ports 1-8, the second 9-16, etc.
els10_27WorkGroupTable	1.3.6.1.4.1.97.9.14.4		not-accessible	This table contains work group definitions for the interfaces.
INT els10_27WorkGroupType	1.3.6.1.4.1.97.9.14.4.1.4	INTEGER	read-write	The type of work group: all - no additional information needs to be supplied.
NTF els10_27WriteStatusTrap	1.3.6.1.4.1.97.0.2			Sent when a bank of Flash EPROM has been erased. If els10-27swdisWriteStatus indicates success, then the unit is ready to be downloaded with the new software.
sigma	1.3.6.1.4.1.97
sys	1.3.6.1.4.1.97.1
INT sysID	1.3.6.1.4.1.97.1.1	INTEGER	read-only
TIK sysReset	1.3.6.1.4.1.97.1.2	TimeTicks	read-write
INT sysTrapPort	1.3.6.1.4.1.97.1.6	INTEGER	read-write

RFC description

Standard Microsystems ELS10 switch MIB for managing bridge STP, interfaces, and trap configuration.

Start monitoring Cabletron Ethernet switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CT-ELS10-MIB

What Is CT-ELS10-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description