DELL-NETWORKING-IF-EXTENSION-MIB

All MIBs › DELL-NETWORKING-IF-EXTENSION-MIB

Organization: Dell Inc

Last Updated: 2014--0-8-

Category: Network Interfaces, Vendor: Dell

Description: Provides extended interface management objects beyond standard IF-MIB for Dell Networking equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DELL-NETWORKING-IF-EXTENSION-MIB?

DELL-NETWORKING-IF-EXTENSION-MIB is a Dell Networking OS (Force10-heritage) enterprise MIB that supplements the standard IETF IF-MIB with additional interface attributes not covered by the base standard. Its general category is interface configuration and status extension, typically adding things like interface mode, additional operational flags, or Dell-specific port properties. It supports monitoring hardware/software interface status beyond basic ifOperStatus/ifAdminStatus, giving finer-grained visibility into port state and configuration on Dell switches/routers. It explicitly depends on and extends IF-MIB (RFC 2863), and is meaningless without the base interface index/table it augments. Typical deployment is a Dell Networking switch or router where an admin needs interface detail beyond what generic IF-MIB provides. Engineers can download the DELL-NETWORKING-IF-EXTENSION-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DELL-NETWORKING-IF-EXTENSION-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Dell Networking (Force10-based) switch/router

Monitoring Examples

No sample objects were provided for this MIB, so specific table/object names cannot be cited; in general such extension MIBs add rows keyed to ifIndex, letting an admin cross-reference an ifIndex from IF-MIB with additional Dell-specific attributes to get a fuller picture of a given port's configuration or status.

Imported Objects

From DELL-NETWORKING-SMI

dellNetMgmt

OBJECT-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
TimeStamp
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
dellNetIfExtensionMib	1.3.6.1.4.1.6027.3.11			Dell Networking OS IF Extenstion MIB.
dellNetIfExtensionMibObject	1.3.6.1.4.1.6027.3.11.1
dellNetIfExtensionParams	1.3.6.1.4.1.6027.3.11.1.1
dellNetIfTable	1.3.6.1.4.1.6027.3.11.1.1.1		not-accessible	Dell Networking OS Extension ifTable contains generic interface parameters.
dellNetIfEntry	1.3.6.1.4.1.6027.3.11.1.1.1.1		not-accessible	A row defintion of Dell Networking OS Interface Extension parameters.
U32 dellNetIfIpMtu	1.3.6.1.4.1.6027.3.11.1.1.1.1.1	Unsigned32	read-write	The IP (Internet Protocol), Maximum Transmission Unit value.
INT dellNetIfDuplexMode	1.3.6.1.4.1.6027.3.11.1.1.1.1.2	INTEGER	read-write	Duplex mode of the interface. This will be read-write only for s60
STR dellNetIfQueueingStrategy	1.3.6.1.4.1.6027.3.11.1.1.1.1.3	DisplayString	read-only	Queueing strategy used for packets.
T/F dellNetIfRxFlowCtrl	1.3.6.1.4.1.6027.3.11.1.1.1.1.4	TruthValue	read-write	Flow control receive. This will be read-write only for s60
T/F dellNetIfTxFlowCtrl	1.3.6.1.4.1.6027.3.11.1.1.1.1.5	TruthValue	read-write	Flow Control transmit.This will be read-only only for s60
OCT dellNetIfDescr	1.3.6.1.4.1.6027.3.11.1.1.1.1.6	OCTET STRING	read-write	A textual string containing information about the interface. This will be read-write only for s60
INT dellNetIfAdminStatus	1.3.6.1.4.1.6027.3.11.1.1.1.1.7	INTEGER	read-write	A admin status of any interface. This will be read-write only for s60
U32 dellNetIfRateInterval	1.3.6.1.4.1.6027.3.11.1.1.1.1.8	Unsigned32	read-write	The rate info interval for the interface. This will be read-write only for s60
INT dellNetIfSpeed	1.3.6.1.4.1.6027.3.11.1.1.1.1.9	INTEGER	read-write	The interface's current bandwidth in bits per second. This will be read-write only for s60
I32 dellNetIfPortListBitPos	1.3.6.1.4.1.6027.3.11.1.1.1.1.10	Integer32	read-only	This is used for identifying the bit position in PortList Object for a given interface.
dellNetIfExtensionStats	1.3.6.1.4.1.6027.3.11.1.2
dellNetIfStaticsTable	1.3.6.1.4.1.6027.3.11.1.2.1		not-accessible	The statistcs information of the interfaces for performance monitoring.
dellNetIfStaticsEntry	1.3.6.1.4.1.6027.3.11.1.2.1.1		not-accessible	A row defintion of Dell Networking OS Extension interface statistics.
C64 dellNetIfInVlanPkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.1	Counter64	read-only	The total number of valid VLAN Tagged frames received.
C64 dellNetIfIn64BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.2	Counter64	read-only	The total number of frames (including bad frames) received that were 64 octets in length (excluding framing bits but in-cluding FCS octets).
C64 dellNetifIn65To127BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.3	Counter64	read-only	The total number of frames (including bad frames) received that were between 65 and 127 octets in length inclusive (ex-cluding framing bits but including FCS octets).
C64 dellNetIfIn128To255BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.4	Counter64	read-only	The total number of frames (including bad frames) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
C64 dellNetIfIn256To511BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.5	Counter64	read-only	The total number of frames (including bad frames) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
C64 dellNetIfIn512To1023BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.6	Counter64	read-only	The total number of frames (including bad frames) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
C64 dellNetIfInOver1023BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.7	Counter64	read-only	The total number of frames received that were longer than 1023 (1025 Bytes in case of VLAN Tag) octets (excluding framing bits, but including FCS octets) and were otherwise well formed. This counter is not incremented for too long frames.
C64 dellNetIfInThrottles	1.3.6.1.4.1.6027.3.11.1.2.1.1.8	Counter64	read-only	This counter is incremented when a valid frame with a length or type field value equal to 0x8808 (Control Frame) is re-ceived.
C64 dellNetIfInRunts	1.3.6.1.4.1.6027.3.11.1.2.1.1.9	Counter64	read-only	The total number of frames received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 dellNetIfInGiants	1.3.6.1.4.1.6027.3.11.1.2.1.1.10	Counter64	read-only	The total number of frames received that were longer than 1518 (1522 Bytes in case of VLAN Tag) octets (excluding framing bits, but including FCS octets) and were otherwise well formed. This counter is not incremented for too long frames.
C64 dellNetIfInCRC	1.3.6.1.4.1.6027.3.11.1.2.1.1.11	Counter64	read-only	The total number of frames received that had a length (ex-cluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had a bad CRC.
C64 dellNetIfInOverruns	1.3.6.1.4.1.6027.3.11.1.2.1.1.12	Counter64	read-only	The total number of frames dropped because of buffer issue.
C64 dellNetIfOutVlanPkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.13	Counter64	read-only	The Number of Good VLAN Tagged Frames sent successfully.
C64 dellNetIfOutUnderruns	1.3.6.1.4.1.6027.3.11.1.2.1.1.14	Counter64	read-only	The total number of frames dropped because of buffer underrun.
C64 dellNetIfOutUnicasts	1.3.6.1.4.1.6027.3.11.1.2.1.1.15	Counter64	read-only	The Number of Good Unicast Frames sent successfully.
C64 dellNetIfOutCollisions	1.3.6.1.4.1.6027.3.11.1.2.1.1.16	Counter64	read-only	A count of the frames that due to excessive or late collisions are not transmitted successfully.
C64 dellNetIfOutWredDrops	1.3.6.1.4.1.6027.3.11.1.2.1.1.17	Counter64	read-only	A count of the frames that are dropped using WRED policy because of to excessive traffic.
C64 dellNetIfOut64BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.18	Counter64	read-only	The Number of Good Frames sent successfully whose size was 64 Bytes.
C64 dellNetIfOut65To127BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.19	Counter64	read-only	The Number of Good Frames sent successfully whose size was in the range of 65 to 127 Bytes.
C64 dellNetIfOut128To255BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.20	Counter64	read-only	The Number of Good Frames sent successfully whose size was in the range of 128 to 255 Bytes.
C64 dellNetIfOut256To511BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.21	Counter64	read-only	The Number of Good Frames sent successfully whose size was in the range of 256 to 511 Bytes.
C64 dellNetIfOut512To1023BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.22	Counter64	read-only	The Number of Good Frames sent successfully whose size was in the range of 512 to 1023 Bytes.
C64 dellNetIfOutOver1023BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.23	Counter64	read-only	The Number of Good Frames sent successfully whose size was greater than 1023 Bytes.
C64 dellNetIfOutThrottles	1.3.6.1.4.1.6027.3.11.1.2.1.1.24	Counter64	read-only	This counter is incremented when a valid frame with a length or type field value equal to 0x8808 (Control Frame) is sent.
TIM dellNetIfLastDiscontinuityTime	1.3.6.1.4.1.6027.3.11.1.2.1.1.25	TimeStamp	read-only	The value of sysUpTime on the most recent occasion at which this interface's counters suffered a discontinuity via a reset. If no such discontinuities have occurred since the last reinitialization of the local management subsystem, then this object contains a zero value.
I32 dellNetIfInCentRate	1.3.6.1.4.1.6027.3.11.1.2.1.1.26	Integer32	read-only	This is the ingress rate in percentage. This is an integer value which can go from 0 to 100.
I32 dellNetIfOutCentRate	1.3.6.1.4.1.6027.3.11.1.2.1.1.27	Integer32	read-only	This is the egress rate in percentage. This is an integer value which can go from 0 to 100.
dellNetIfExtensionMibConformance	1.3.6.1.4.1.6027.3.11.2
dellNetIfExtensionMibCompliances	1.3.6.1.4.1.6027.3.11.2.1
dellNetIfExtensionMibCompliance	1.3.6.1.4.1.6027.3.11.2.1.1			The compliance statement for Dell Networking OS IF Extension MIB.
dellNetIfExtensionMibGroups	1.3.6.1.4.1.6027.3.11.2.2
dellNetIfParamsGroup	1.3.6.1.4.1.6027.3.11.2.2.1			A collection of objects providing the Dell Networking OS IF Extenstion parameters.
dellNetIfStatsGroup	1.3.6.1.4.1.6027.3.11.2.2.2			A collection of objects providing the interface statistics.

RFC description

Extends IF-MIB with Dell Networking OS interface and statistics parameters.

Start monitoring Dell Networking (Force10-based) switch/router (interface extension) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DELL-NETWORKING-IF-EXTENSION-MIB

What Is DELL-NETWORKING-IF-EXTENSION-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description