COLUBRIS-DEVICE-WIRELESS-MIB

MIB Reference — IPNetwork Monitor · Updated September 14, 2026

All MIBsCOLUBRIS-DEVICE-WIRELESS-MIB

Organization: Colubris Networks, Inc.

Last Updated: 2009-06-01

Category: Vendor: HP/HPE, Wireless and WLAN

Description: Monitors wireless radio channel, transmit power, and association stats on Colubris/HP access points.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is COLUBRIS-DEVICE-WIRELESS-MIB?

This Colubris (HP) MIB covers the radio-level configuration and status of wireless interfaces on Colubris access points, including channel, transmit power, operating mode, and signal-to-noise ratio (SNR) monitoring/notification settings. It exposes both configuration objects (minimum SNR threshold, notification enable/interval) and status objects per wireless interface (current operating channel, transmit power, radio mode). Its core monitoring role is radio hardware health and RF performance: an operator watches SNR level notifications to catch degrading radio conditions, and reads the interface status table to confirm a radio is running the expected channel/power/mode, all direct indicators of wireless hardware performance. It naturally depends on the same interface-indexing conventions used across Colubris's device MIB family (e.g., coDeviceIfStatusTable's ifIndex). It's deployed on Colubris/HP access points in enterprise or outdoor WLAN deployments needing RF health monitoring. Network engineers evaluating or troubleshooting this functionality can download the COLUBRIS-DEVICE-WIRELESS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in COLUBRIS-DEVICE-WIRELESS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

  • Colubris/HP wireless access point

Monitoring Examples

An admin enables coDevWirSNRLevelNotificationEnabled with a coDevWirMinimumSNRLevel threshold so the AP traps when a client or link's SNR drops too low, indicating RF interference or distance problems. Polling coDeviceWirelessInterfaceStatusTable for a given coDevWirIfStaRadioIndex shows coDevWirIfStaOperatingChannel and coDevWirIfStaTransmitPower, letting the admin confirm the radio hasn't drifted from its assigned channel or unexpectedly changed power level. coDevWirAssociationNotificationEnabled would be checked to confirm client association traps are active for tracking connect/disconnect events.

What Can Be Monitored

  • radio SNR level
  • operating channel
  • transmit power
  • radio operating mode
  • client association events
Imported Objects

From COLUBRIS-DEVICE-MIB

coDevDisIndexOBJECT-TYPE

From COLUBRIS-SMI

colubrisMgmtV2OBJECT-IDENTITY

From COLUBRIS-TC

ColubrisNotificationEnable
ColubrisRadioType
ColubrisSSID
ColubrisSSIDOrNone

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
TruthValue

How to Use in IPNetwork Monitor

Example using coDevWirIfStsTransmittedFragmentCount OID:

Select a Colubris/HP wireless access point (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type coDevWirIfStsTransmittedFragmentCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This counter is incremented for each acknowledged MPDU with an individual address in the address 1 field or an MPDU with a multicast address in the address 1 field of type Data or Management. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs

RFC description

Provides wireless device management for Colubris controllers including status, statistics, QoS, and client information.

Start monitoring Colubris/HP wireless access point (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download COLUBRIS-DEVICE-WIRELESS-MIB