All MIBs › CISCO-POP-MGMT-MIB
Organization: Cisco Systems, Inc.
Last Updated: 2005-12-21
Category: Cisco Devices, DSL and Broadband, Network Interfaces
Description: Manages Point of Presence (PoP) resources including access concentrators and subscriber sessions on Cisco platforms.
IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring CISCO-POP-MGMT-MIB with a free 30-day trial of IPNetwork Monitor.
What Is CISCO-POP-MGMT-MIB?
CISCO-POP-MGMT-MIB manages Point-of-Presence dial-access resources on Cisco access-concentrator platforms, providing DSX1 (T1/E1) and DSX0 (channel) facilities management along with call summaries. It exposes configuration data about how DS0 channels are configured and encapsulated, plus per-call operational data including call type, encapsulation, duration, and octet counts. It supports monitoring hardware/service status of dial-access infrastructure -- cpmCallCount and cpmTimeInUse show channel utilization, and cpmInOctets/cpmOutOctets reveal traffic volume per call, together indicating whether DS0 resources are healthy, saturated, or underused, while call-failure objects flag connection setup problems. It focuses on Cisco's own DS0/DS1 facilities model and is typically used alongside standard interface (IF-MIB) and DS1/DS0 MIBs for full circuit-level detail. It is deployed on Cisco access-server/POP concentrator platforms terminating large numbers of dial-in DS0/DS1 circuits, such as ISP dial-access points of presence. Engineers can download the CISCO-POP-MGMT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-POP-MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco dial-access server / Point-of-Presence (PoP) concentrator
Monitoring Examples
cpmDS0UsageTable/cpmDS0UsageEntry rows, indexed by cpmDS1SlotIndex, cpmDS1PortIndex, and cpmChannelIndex, expose cpmDS0CallType, cpmL2Encapsulation, cpmCallCount, and cpmTimeInUse, letting an administrator see how heavily a given DS0 channel has been used for dial-in calls. cpmInOctets and cpmOutOctets reveal traffic volume per channel -- a channel with high cpmCallCount but very low octet counts might indicate short-lived or failing call attempts. The ciscoPopMgmtMIBObjects group's cpmCallFailure data would be checked when subscribers report repeated connection failures at a POP.
What Can Be Monitored
- DS0 channel call count
- channel time-in-use
- inbound/outbound octet counts per call
- call encapsulation type
- call failure counts
This MIB depends on
Related MIBs
Imported Objects
From CISCO-SMI
| ciscoExperiment | OBJECT-IDENTITY |
From DS1-MIB
| dsx1LineIndex | OBJECT-TYPE |
| dsx1LineStatus | OBJECT-TYPE |
From IF-MIB
| InterfaceIndexOrZero |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| TimeStamp | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using cpmActiveDS0sHighWaterMark OID:
Select a Cisco dial-access server / Point-of-Presence (PoP) concentrator as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cpmActiveDS0sHighWaterMark into the Find box to locate it in the OID tree, then select it and click OK. The high water mark for number of DS0s that are active simultaneously. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the value climbs close to a level you consider a practical ceiling for this device, since a rising peak often signals sustained load growth worth planning capacity around. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ciscoPopMgmtMIB | 1.3.6.1.4.1.9.10.19 | Cisco Point Of Presence Management MIB to provide DSX1 and DSX0 facilities management and call summaries. | ||
| ciscoPopMgmtMIBObjects | 1.3.6.1.4.1.9.10.19.1 | |||
| TIK cpmActiveCallDuration | 1.3.6.1.4.1.9.10.19.1.3.1.1.8 | TimeTicks | read-only | The duration of the current call. |
| TIM cpmActiveCallStartTimeIndex | 1.3.6.1.4.1.9.10.19.1.3.1.1.1 | TimeStamp | not-accessible | The start time of the current call. |
| cpmActiveCallSummary | 1.3.6.1.4.1.9.10.19.1.3 | |||
| cpmActiveCallSummaryEntry | 1.3.6.1.4.1.9.10.19.1.3.1.1 | not-accessible | An entry in the Call Summary table. | |
| cpmActiveCallSummaryGroup | 1.3.6.1.4.1.9.10.19.3.2.3 | A collection of objects providing the summary of the currently active calls. | ||
| I32 cpmActiveCallSummaryIndex | 1.3.6.1.4.1.9.10.19.1.3.1.1.2 | Integer32 | not-accessible | Arbitrary small integer to distinguish calls that occured at the same time tick. |
| cpmActiveCallSummaryTable | 1.3.6.1.4.1.9.10.19.1.3.1 | not-accessible | The active call summary table is needed to track currently active calls. This table is needed because modem calls are not in CALL-HISTORY-MIB, and the DIAL-CONTROL_MIB is not yet available. | |
| INT cpmActiveCallType | 1.3.6.1.4.1.9.10.19.1.3.1.1.5 | INTEGER | read-only | The call type: unknown - None of the following analog - Modem call digital - Digital call v110 - V110 Call v120 - V120 Call voice - Voice Call |
| G32 cpmActiveDS0s | 1.3.6.1.4.1.9.10.19.1.1.4 | Gauge32 | read-only | The number of DS0s that are currently in use. |
| C32 cpmActiveDS0sHighWaterMarkEx | 1.3.6.1.4.1.9.10.19.1.1.8 | Counter32 | read-only | The high water mark for number of DS0s that are active simultaneously |
| I32 cpmActiveEntryChannel | 1.3.6.1.4.1.9.10.19.1.3.1.1.11 | Integer32 | read-only | The channel within the DS1 that is allocated to the call. |
| I32 cpmActiveEntryPort | 1.3.6.1.4.1.9.10.19.1.3.1.1.10 | Integer32 | read-only | The logical port for the DS1 line that the user connected on. |
| I32 cpmActiveEntrySlot | 1.3.6.1.4.1.9.10.19.1.3.1.1.9 | Integer32 | read-only | The logical slot in which the DS1 line that the user connected on resides. |
| STR cpmActiveLocalPhoneNumber | 1.3.6.1.4.1.9.10.19.1.3.1.1.13 | DisplayString | read-only | The local telephone number. For a call into the device, this is the dialed number. For a call out of the device, this is the originating number. If not available the string length is zero. |
| I32 cpmActiveModemPort | 1.3.6.1.4.1.9.10.19.1.3.1.1.7 | Integer32 | read-only | Identification of modem resource allocated to call. This is the value of cmPortIndex from CISCO-MODEM-MGMT-MIB. This value along with cpmActiveModemSlot uniquely identifies a modem. Value is -1 if call does not utilize a modem. |
| I32 cpmActiveModemSlot | 1.3.6.1.4.1.9.10.19.1.3.1.1.6 | Integer32 | read-only | Identification of modem resource allocated to call. This is the value of cmSlotIndex from CISCO-MODEM-MGMT-MIB. This value along with cpmActiveModemPort uniquely identifies a modem. Value is -1 if call does not utilize a modem. |
| STR cpmActiveRemotePhoneNumber | 1.3.6.1.4.1.9.10.19.1.3.1.1.12 | DisplayString | read-only | The remote telephone number. For a call into the device, this is the originating number. For a call out of the device, this is the dialed number. If not available the string length is zero. |
| I32 cpmActiveTTYNumber | 1.3.6.1.4.1.9.10.19.1.3.1.1.14 | Integer32 | read-only | The TTY number associated with this call. This information comes from the IOS 'show line' command. |
| STR cpmActiveUserID | 1.3.6.1.4.1.9.10.19.1.3.1.1.3 | DisplayString | read-only | The User login ID or zero length string if unavailable. |
| IP cpmActiveUserIpAddr | 1.3.6.1.4.1.9.10.19.1.3.1.1.4 | IpAddress | read-only | The IP address of the call or 0.0.0.0 if unavailable. This object comes directly from IOS. |
| NUM cpmAssociatedInterface | 1.3.6.1.4.1.9.10.19.1.1.1.1.13 | InterfaceIndexOrZero | read-only | This is the value of ifIndex when the specific channel has an active call with a corresponding interface in the ifTable. For example, a digital ISDN call has a value pointing to the B-Channel entry in the ifTable. A modem call over ISDN or CT1/CE1 has a value pointing to the async interface of the modem assigned to this call. If the channel is idle, this value is 0. |
| C32 cpmCallCount | 1.3.6.1.4.1.9.10.19.1.1.1.1.7 | Counter32 | read-only | The number of calls that have occupied this DS0. |
| TIM cpmCallDisconnectTimeIndex | 1.3.6.1.4.1.9.10.19.1.4.3.1.1 | TimeStamp | not-accessible | The disconnect time of the call. |
| TIK cpmCallDuration | 1.3.6.1.4.1.9.10.19.1.4.3.1.9 | TimeTicks | read-only | The duration of the current call. |
| cpmCallFailure | 1.3.6.1.4.1.9.10.19.1.2 | |||
| cpmCallFailureGroup | 1.3.6.1.4.1.9.10.19.3.2.2 | A collection of objects providing aggregate totals of call failures | ||
| cpmCallHistorySummary | 1.3.6.1.4.1.9.10.19.1.4 | |||
| cpmCallHistorySummaryEntry | 1.3.6.1.4.1.9.10.19.1.4.3.1 | not-accessible | An entry in the Call Summary table. | |
| cpmCallHistorySummaryGroup | 1.3.6.1.4.1.9.10.19.3.2.4 | A collection of objects providing the summary of calls that were recently terminated. | ||
| I32 cpmCallHistorySummaryIndex | 1.3.6.1.4.1.9.10.19.1.4.3.1.3 | Integer32 | not-accessible | Arbitrary small integer to distinguish calls that occured at the same time tick. |
| I32 cpmCallHistorySummaryRetainTimer | 1.3.6.1.4.1.9.10.19.1.4.2 | Integer32 | read-write | The minimum amount of time that an cpmCallHistoryEntry will be maintained before being deleted. A value of 0 will prevent any history from being retained, but will not prevent callCompletion traps being genarated. |
| cpmCallHistorySummaryTable | 1.3.6.1.4.1.9.10.19.1.4.3 | not-accessible | The call history summary table is needed to track ended active calls. This table is needed because modem calls are not in CALL-HISTORY-MIB; the CISCO-ISDN-MIB objects do not contain information about the active calls; and the DIAL-CONTROL_MIB is not yet available. | |
| I32 cpmCallHistorySummaryTableMaxLength | 1.3.6.1.4.1.9.10.19.1.4.1 | Integer32 | read-write | The upper limit on the number of entries that the cpmCallHistoryTable may contain. A value of 0 will prevent any history from being retained. When this table is full, the oldest entry will be deleted and the new one will be created. |
| TIM cpmCallStartTimeIndex | 1.3.6.1.4.1.9.10.19.1.4.3.1.2 | TimeStamp | not-accessible | The start time of the current call. |
| INT cpmCallType | 1.3.6.1.4.1.9.10.19.1.4.3.1.6 | INTEGER | read-only | The call type: unknown - None of the following analog - Modem call digital - Digital call v110 - V110 Call v120 - V120 Call voice - Voice Call |
| C32 cpmCallVolAnalogCallClearedNormally | 1.3.6.1.4.1.9.10.19.1.7.2 | Counter32 | read-only | The number of incoming and outgoing successful analog data calls which use modem resource (cpmDS0CallType has the value 'analog(3)'), since system startup. A successful call is a terminated call who is cleared by the proper modem protocol handshake. |
| C32 cpmCallVolSuccISDNDigital | 1.3.6.1.4.1.9.10.19.1.7.1 | Counter32 | read-only | The number of incoming and outgoing successful ISDN digital data calls (cpmDS0CallType has the value 'digital(4)'), since system startup. A successful call is a terminated call that has a disconnect cause of 'normal call clearing(16)'. |
| cpmCallVolume | 1.3.6.1.4.1.9.10.19.1.7 | |||
| cpmCallVolumeGroup | 1.3.6.1.4.1.9.10.19.3.2.12 | A collection of objects providing aggregate totals of call successfully completed | ||
| G32 cpmCASCfgBChanInUseForVoice | 1.3.6.1.4.1.9.10.19.1.1.12 | Gauge32 | read-only | The number of configured CAS Channels that are currently occupied by Voice calls. |
| I32 cpmChannelIndex | 1.3.6.1.4.1.9.10.19.1.1.1.1.3 | Integer32 | not-accessible | The channel index that distinguishes the DS0 timeslot of the DS1 port. The range of the channel index is based on the number of T1/E1 channels: 1-24(T1) and 1-31(E1). |
| cpmComplianceRev2 | 1.3.6.1.4.1.9.10.19.3.1.3 | The compliance statement used in a PoPM Stack, which implement the Cisco PoP Management MIB | ||
| INT cpmConfiguredType | 1.3.6.1.4.1.9.10.19.1.1.1.1.4 | INTEGER | read-only | The configured technology for the channel: ISDN(2), Channelized T1 (3) or Channelized E1 (4). |
| INT cpmDS0BusyoutAdminStatus | 1.3.6.1.4.1.9.10.19.1.5.2.1.2 | INTEGER | read-write | The administratively requested busyout state of the DSO. This object represents the desired busyout state of the DS0, which may or may not be reflected in the operation state, cpmDS0OperStatus. This object may be set via SNMP or the system console. noBusyout - No administrative busyout has been requested busyout - The DS0 will be shutdown when it next transitions to idle(2) cpmDS0OperStatus busyoutImmediate - Immediately transition the DS0 to down(2), terminating any current activity The effect of setting this object to busyout or busyoutImmediate is constrained by the value of cpmDS0BusyoutAllowed. If cpmDS0BusyoutAllowed has a value of false, attempting to set this object to busyout or busyoutImmediate will fail. This object provides more busyout information not available from the IF-MIB ifAdminStatus. This object reflects busyout requests configured on the local system as defined for the object cpmDS0BusyoutSource. |
| T/F cpmDS0BusyoutAllow | 1.3.6.1.4.1.9.10.19.1.5.2.1.3 | TruthValue | read-only | The object indicates if busyout requests for this DSO will be allowed. true - Setting cpmDS0BusyoutAdminStatus to busyout(2) or busyoutImmediate(3) will be accepted false - Busyout requests for this DS0 are not allowed The default value is true(1). If cpmDS0BusyoutAllowed has a value of false(2), attempting to set cpmDS0BusyoutAdminStatus to busyout or busyoutImmediate will fail. This object only constrains setting the value of cpmDS0BusyoutAdminStatus when cpmDS0BusyoutAdminStatus is set via SNMP. |
| NTF cpmDS0BusyoutNotification | 1.3.6.1.4.1.9.10.19.2.0.1 | This notification is sent when there is a state change in cpmDS0BusyoutStatus object. | ||
| T/F cpmDS0BusyoutNotifyEnable | 1.3.6.1.4.1.9.10.19.1.5.1 | TruthValue | read-write | This variable controls generation of cpmDS0BusyoutNotification. When this variable is 'true(1)', generation of cpmDS0BusyoutNotification is enabled. When this variable is 'false(2)', generation of cpmDS0BusyoutNotification is disabled. The default value is 'false(2)'. |
| INT cpmDS0BusyoutSource | 1.3.6.1.4.1.9.10.19.1.5.2.1.5 | INTEGER | read-only | The source of the busyout request either pending or active for the DSO. none - The DS0 is not busied out nor has a busyout request pending local - The DS0 is busied out or has a pending request due to an adminstrative command issued locally. internal - The DS0 is busied out or has a pending request due to internal system processing. remote - The DS0 is busied out or has a pending request due to a request from the peer switch. |
| INT cpmDS0BusyoutStatus | 1.3.6.1.4.1.9.10.19.1.5.2.1.4 | INTEGER | read-only | The busyout status of the DSO. noBusyout - The DS0 is not busied out nor has a busyout pending. busyoutPending - The DS0 has a busyout request pending. It will shutdown when it next transitions to idle(2) cpmDS0OperStatus. busiedOut - The DS0 is out of service due to a busyout request. This object is needed to reflect busyouts initiated other than administrativly, as described in cpmDS0BusyoutSource. |
| TIM cpmDS0BusyoutTime | 1.3.6.1.4.1.9.10.19.1.5.2.1.6 | TimeStamp | read-only | Value of sysUpTime when the most recent busyout request was issued for this DS0. The value is zero indicates no busyout request has been issued. |
| INT cpmDS0CallType | 1.3.6.1.4.1.9.10.19.1.1.1.1.5 | INTEGER | read-only | The type of the current call carried by this DS0. idle - This DS0 is currently idle. unknown - The data type of the call currently occupying this DS0 is not one of the types listed here. analog - The data type of the call currently occupying this DS0 is analog, i.e. a modem call. digital - The data type of the call currently occupying this DS0 is digital. v110 - The call currently occupying this DS0 is a V110 call. v120 - The call currently occupying this DS0 is a V120 call. voice - The call currently occupying this DS0 is a voice call. |
| INT cpmDS0ConfigFunction | 1.3.6.1.4.1.9.10.19.1.5.2.1.7 | INTEGER | read-only | The object indicates the function this DSO is configured to provide. This object provides more detail than cpmConfiguredType. unknown - Unknown configuration t1SignallingChan - DS0 is configured as a T1 common channel signalling (CCS) such as ISDN PRI D-channel t1CcsBearerChan - DS0 is configured as a T1 common channel signalling (CCS) bearer channel e1SignallingChan - DS0 is configured as a E1 common channel signalling (CCS) such as ISDN PRI D-channel e1CcsBearerChan - DS0 is configured as a E1 common channel signalling (CCS) bearer channel t1CasChan - DS0 is configured as a T1 channel associated signalling channel e1CasChan - DS0 is configured as a E1 channel associated signalling channel |
| NUM cpmDS0InterfaceIndex | 1.3.6.1.4.1.9.10.19.1.5.2.1.8 | InterfaceIndexOrZero | read-only | This is the value of ifIndex in the ifTable for this DS0. |
| INT cpmDS0OperStatus | 1.3.6.1.4.1.9.10.19.1.5.2.1.1 | INTEGER | read-only | The operational state of the DSO. This object provides more detailed information than the IF-MIB ifOperStatus. unknown - The DSO is in an unknown state down - The DS0 is out of service idle - This DS0 is currently idle setup - A new connection is in the process of being established connected - A active connection exists test - The DSO is undergoing internal testing |
| cpmDS0Status | 1.3.6.1.4.1.9.10.19.1.5 | |||
| cpmDS0StatusEntry | 1.3.6.1.4.1.9.10.19.1.5.2.1 | not-accessible | Status for an individual DS0. This entry AUGMENTS the cpmDS0UsageEntry. An entry exists for each configured DS0 in the system. | |
| cpmDS0StatusGroup | 1.3.6.1.4.1.9.10.19.3.2.9 | A collection of objects providing the status for a DS0. | ||
| cpmDS0StatusTable | 1.3.6.1.4.1.9.10.19.1.5.2 | not-accessible | The DS0 Status Table provides additional DS0 level information and configuration. This table is an extension of the cpmDS0UsageTable. | |
| cpmDS0Usage | 1.3.6.1.4.1.9.10.19.1.1 | |||
| cpmDS0UsageEntry | 1.3.6.1.4.1.9.10.19.1.1.1.1 | not-accessible | An entry in the DS0 Usage table. | |
| cpmDS0UsageGroup | 1.3.6.1.4.1.9.10.19.3.2.1 | A collection of objects providing the analog and digital statistics for a DS1. | ||
| cpmDS0UsageGroupRev1 | 1.3.6.1.4.1.9.10.19.3.2.5 | A collection of objects providing the analog and digital statistics for a DS1. | ||
| cpmDS0UsageGroupRev2 | 1.3.6.1.4.1.9.10.19.3.2.6 | A collection of objects providing the analog and digital statistics for a DS1. | ||
| cpmDS0UsageTable | 1.3.6.1.4.1.9.10.19.1.1.1 | not-accessible | The DS0 usage table is for hardware and software objects not used as interfaces, and not covered in rfc1213. These objects include analog calls coming over ISDN, Channelized T1, and Channelized E1. This table is created for every DS1 line in the device. | |
| G32 cpmDS1ActiveDS0s | 1.3.6.1.4.1.9.10.19.1.1.9.1.3 | Gauge32 | read-only | The number of DS0s that are currently in use for a particular DS1. |
| C32 cpmDS1ActiveDS0sHighWaterMark | 1.3.6.1.4.1.9.10.19.1.1.9.1.4 | Counter32 | read-only | The highest number of simultaneously actived DS0s on a specified DS1. |
| G32 cpmDS1CurrentBusyout | 1.3.6.1.4.1.9.10.19.1.1.9.1.13 | Gauge32 | read-only | The total number of DS0s in this DS1 which currently have been requested to be busied out, but are not yet out of service. When an active call on a busied out DS0 terminates, the DS0 will be out of service, this object will be decremented and cpmDS1TotalOutOfService will be incremented. This only includes DS0s configured as bearer channels, not those configured for signaling, such as PRI D-channel. See cpmDS0AdminStatus in the cpmDS0StatusTable for individual DS0s. |
| G32 cpmDS1CurrentIdle | 1.3.6.1.4.1.9.10.19.1.1.9.1.11 | Gauge32 | read-only | The total number of DS0s currently in idle state within this DS1. This only includes DS0s configured as bearer and CAS channels, not those configured for signaling, such as PRI D-channel. See cpmDS0OperStatus in the cpmDS0StatusTable for individual DS0s. |
| G32 cpmDS1CurrentOutOfService | 1.3.6.1.4.1.9.10.19.1.1.9.1.12 | Gauge32 | read-only | The total number of DS0s in this DS1 currently placed out of service. This only includes DS0s configured as bearer and CAS channels, not those configured for signaling, such as PRI D-channel. See cpmDS0OperStatus in the cpmDS0StatusTable for individual DS0s. |
| cpmDS1DS0UsageEntry | 1.3.6.1.4.1.9.10.19.1.1.9.1 | not-accessible | An entry in the DS0 Usage table. | |
| cpmDS1DS0UsageTable | 1.3.6.1.4.1.9.10.19.1.1.9 | not-accessible | The DS1-DS0-usage table is for hardware and software objects not used as interfaces, and not covered in rfc1213. These objects provide information on timeslots usage for a particular DS1. | |
| C32 cpmDS1InOctets | 1.3.6.1.4.1.9.10.19.1.1.9.1.14 | Counter32 | read-only | The total number of octets received over all the DS0 bearer channels within this DS1 since last system re-initialization. This value is a sum of all the cpmInOctets objects in the cpmDS0UsageTable for this DS1. |
| C32 cpmDS1InPackets | 1.3.6.1.4.1.9.10.19.1.1.9.1.16 | Counter32 | read-only | The total number of data packets received over all the DS0 bearer channels within this DS1 since last system re-initialization. This value is a sum of all the cpmInPackets objects in the cpmDS0UsageTable for this DS1. It consists of PPP or PCM voice data packets. |
| NTF cpmDS1LoopbackNotification | 1.3.6.1.4.1.9.10.19.2.0.2 | This notification is sent when there is a state change in dsx1LineStatus object of RFC1406-MIB. | ||
| cpmDS1LoopbackNotifyConfig | 1.3.6.1.4.1.9.10.19.1.6 | |||
| cpmDS1LoopbackNotifyConfigGroup | 1.3.6.1.4.1.9.10.19.3.2.11 | A collection of objects providing the notification configuration | ||
| T/F cpmDS1LoopbackNotifyEnable | 1.3.6.1.4.1.9.10.19.1.6.1 | TruthValue | read-write | This variable controls the generation of cpmDS1LoopbackNotification When this variable is 'true(1)', generation of these notification is enabled. When this variable is 'false(2)', generation is disabled The default value is 'false(2)'. |
| C32 cpmDS1OutOctets | 1.3.6.1.4.1.9.10.19.1.1.9.1.15 | Counter32 | read-only | The total number of octets transmitted over all the DS0 bearer channels within this DS1 since last system re-initialization. This value is a sum of all the cpmOutOctets objects in the cpmDS0UsageTable for this DS1. |
| C32 cpmDS1OutPackets | 1.3.6.1.4.1.9.10.19.1.1.9.1.17 | Counter32 | read-only | The total number of data packets transmitted over all the DS0 bearer channels within this DS1 since last system re-initialization. This value is a sum of all the cpmOutPackets objects in the cpmDS0UsageTable for this DS1. It consists of PPP or PCM voice data packets. |
| I32 cpmDS1PortIndex | 1.3.6.1.4.1.9.10.19.1.1.1.1.2 | Integer32 | not-accessible | The port index indicates the port number of a specific DS1 on the DS1 card in the slot |
| I32 cpmDS1SlotIndex | 1.3.6.1.4.1.9.10.19.1.1.1.1.1 | Integer32 | not-accessible | The slot index indicates the slot number on the device where the DS1 card resides. |
| C32 cpmDS1TotalAnalogCalls | 1.3.6.1.4.1.9.10.19.1.1.9.1.5 | Counter32 | read-only | The accumulated number of analog data calls (cpmDS0CallType has the value 'analog(3)') on all ds0s within this DS1 since system startup. The object includes active and terminated calls. |
| C32 cpmDS1TotalCalls | 1.3.6.1.4.1.9.10.19.1.1.9.1.9 | Counter32 | read-only | The total number of calls on all the DS0s within this DS1 since last system re-initialization. The object includes active and terminated calls. This only includes DS0s configured as bearer channels, not those configured for signaling, such as PRI D-channel. |
| C32 cpmDS1TotalDigitalCalls | 1.3.6.1.4.1.9.10.19.1.1.9.1.6 | Counter32 | read-only | The accumulated number of digital data calls (cpmDS0CallType has the value 'digital(4)') on all ds0s within this DS1 since system startup. The object includes active and terminated calls. |
| U32 cpmDS1TotalTimeInUse | 1.3.6.1.4.1.9.10.19.1.1.9.1.10 | Unsigned32 | read-only | The total call duration on all the DS0s within this DS1 since last system re-initialization. This only includes DS0s configured as bearer channels, not those configured for signaling, such as PRI D-channel. |
| C32 cpmDS1TotalV110Calls | 1.3.6.1.4.1.9.10.19.1.1.9.1.7 | Counter32 | read-only | The accumulated number of v.110 data calls (cpmDS0CallType has the value 'v110(5)') on all ds0s within this DS1 since system startup. The object includes active and terminated calls. |
| C32 cpmDS1TotalV120Calls | 1.3.6.1.4.1.9.10.19.1.1.9.1.8 | Counter32 | read-only | The accumulated number of v.120 data calls (cpmDS0CallType has the value 'v120(6)') on all ds0s within this DS1 since system startup. The object includes active and terminated calls. |
| cpmDS1UsageGroup | 1.3.6.1.4.1.9.10.19.3.2.7 | A collection of objects providing statistics aggregation across DS0s within a DS1. | ||
| I32 cpmDS1UsagePortIndex | 1.3.6.1.4.1.9.10.19.1.1.9.1.2 | Integer32 | not-accessible | The port index indicates the port number of a specific DS1 on the DS1 card in the slot. The port index of the first port is starting from 0 and increment by 1 for the next port on the DS1 card. |
| I32 cpmDS1UsageSlotIndex | 1.3.6.1.4.1.9.10.19.1.1.9.1.1 | Integer32 | not-accessible | The slot index indicates the slot number on the device where the DS1 card resides. The slot index of the first slot is starting from 0 and increment by 1 for the next slot in the device. |
| I32 cpmEntryChannel | 1.3.6.1.4.1.9.10.19.1.4.3.1.12 | Integer32 | read-only | The channel within the DS1 that is allocated to the call. |
| I32 cpmEntryPort | 1.3.6.1.4.1.9.10.19.1.4.3.1.11 | Integer32 | read-only | The logical port for the DS1 line that the user connected on. |
| I32 cpmEntrySlot | 1.3.6.1.4.1.9.10.19.1.4.3.1.10 | Integer32 | read-only | The physical system slot in which the DS1 line that the user connected on resides. |
| C32 cpmInOctets | 1.3.6.1.4.1.9.10.19.1.1.1.1.9 | Counter32 | read-only | The total number of octets received on this DS0 for data calls (cpmDS0CallType has the value 'analog(3)' or 'digital(4)' or 'v110(5)' or 'v120(6)'). All the received 'raw' octets are counted, including any protocol headers which may or may not be present, depending on the service type of data call. |
| C32 cpmInPackets | 1.3.6.1.4.1.9.10.19.1.1.1.1.11 | Counter32 | read-only | The total number of packets received on this DS0 for data calls (cpmDS0CallTyp has the value 'analog(3)' or 'digital(4)' or 'v110(5)' or 'v120(6)'). |
| C32 cpmISDNCallsClearedAbnormally | 1.3.6.1.4.1.9.10.19.1.2.3 | Counter32 | read-only | The number of connected ISDN calls that have been abnormally cleared, that is, they were cleared by some event other than the following: a - The transmission of a normal disconnect message by the local end. b - The reception of a normal disconnect message from the remote end. |
| C32 cpmISDNCallsRejected | 1.3.6.1.4.1.9.10.19.1.2.1 | Counter32 | read-only | The number of rejected ISDN calls in this managed device. |
| G32 cpmISDNCfgActiveDChannels | 1.3.6.1.4.1.9.10.19.1.1.13 | Gauge32 | read-only | The number of ISDN signaling channels which are active. |
| G32 cpmISDNCfgBChanInUseForAnalog | 1.3.6.1.4.1.9.10.19.1.1.2 | Gauge32 | read-only | The number of configured ISDN B-Channels that are currently occupied by analog calls. |
| G32 cpmISDNCfgBChanInUseForVoice | 1.3.6.1.4.1.9.10.19.1.1.11 | Gauge32 | read-only | The number of configured ISDN B-Channels that are currently occupied by Voice calls. |
| C32 cpmISDNCfgBChannelAnalogCalls | 1.3.6.1.4.1.9.10.19.1.1.17 | Counter32 | read-only | The total number of analog calls on all the ISDN B-channels since last system re-initialization. Analog call type is identified in cpmDS0CallType. |
| C32 cpmISDNCfgBChannelCalls | 1.3.6.1.4.1.9.10.19.1.1.16 | Counter32 | read-only | The total number of calls on all the ISDN B-channels since last system re-initialization. |
| G32 cpmISDNCfgBChannelsInUse | 1.3.6.1.4.1.9.10.19.1.1.3 | Gauge32 | read-only | The number of configured ISDN B-Channels that are currently occupied by both Digital and Analog calls. |
| C32 cpmISDNCfgBChannelsTimeInUse | 1.3.6.1.4.1.9.10.19.1.1.14 | Counter32 | read-only | The total call duration on all the ISDN B-channels since last system re-initialization. |
| C32 cpmISDNCfgBChannelsTimeInUseAnlg | 1.3.6.1.4.1.9.10.19.1.1.15 | Counter32 | read-only | The total analog call duration on all the ISDN B-channels since last system re-initialization. Analog call type is identified in cpmDS0CallType. |
| C32 cpmISDNNoResource | 1.3.6.1.4.1.9.10.19.1.2.5 | Counter32 | read-only | The number of ISDN calls that have been rejected because there is no B-Channel available to handle the call. |
| INT cpmL2Encapsulation | 1.3.6.1.4.1.9.10.19.1.1.1.1.6 | INTEGER | read-only | The data link encapsulation of the call currently occuppying this DS0: idle - This DS0 is currently idle. unknown - The encapsulation of the currently active call on this DS0 is not one of the options following. PPP - slip - arap - hdlc - exec - voice - voice encapsulation; IANA type voiceEncap(103) |
| STR cpmLocalPhoneNumber | 1.3.6.1.4.1.9.10.19.1.4.3.1.14 | DisplayString | read-only | The local telephone number. For a call into the device, this is the dialed number. For a call out of the device, this is the originating number. If not available the string length is zero. |
| cpmMIBCompliance | 1.3.6.1.4.1.9.10.19.3.1.1 | The compliance statement used in a PoPM Stack, which implement the Cisco PoP Management MIB | ||
| cpmMIBComplianceRev1 | 1.3.6.1.4.1.9.10.19.3.1.2 | The compliance statement used in a PoPM Stack, which implement the Cisco PoP Management MIB | ||
| cpmMIBComplianceRev3 | 1.3.6.1.4.1.9.10.19.3.1.4 | The compliance statement used in a PoPM Stack, which implement the Cisco PoP Management MIB | ||
| cpmMIBComplianceRev4 | 1.3.6.1.4.1.9.10.19.3.1.5 | The compliance statement used in a PoPM Stack, which implement the Cisco PoP Management MIB | ||
| cpmMIBComplianceRev5 | 1.3.6.1.4.1.9.10.19.3.1.6 | The compliance statement used in a PoPM Stack, which implement the Cisco PoP Management MIB | ||
| cpmMIBCompliances | 1.3.6.1.4.1.9.10.19.3.1 | |||
| cpmMIBConformance | 1.3.6.1.4.1.9.10.19.3 | |||
| cpmMIBGroups | 1.3.6.1.4.1.9.10.19.3.2 | |||
| C32 cpmModemCallsClearedAbnormally | 1.3.6.1.4.1.9.10.19.1.2.4 | Counter32 | read-only | The number of connected modem calls that have been abnormally cleared, that is, they were not cleared with the proper modem protocol handshakes. |
| C32 cpmModemCallsRejected | 1.3.6.1.4.1.9.10.19.1.2.2 | Counter32 | read-only | The number of rejected modem calls in this managed device. |
| C32 cpmModemNoResource | 1.3.6.1.4.1.9.10.19.1.2.6 | Counter32 | read-only | The number of modem calls that have been rejected because there is no modem available to handle the call. |
| I32 cpmModemPort | 1.3.6.1.4.1.9.10.19.1.4.3.1.8 | Integer32 | read-only | Identification of modem resource allocated to call. This is the value of cmPortIndex from CISCO-MODEM-MGMT-MIB. This value along with cpmModemSlot uniquely identifies a modem. Value is -1 if call does not utilize a modem. |
| I32 cpmModemSlot | 1.3.6.1.4.1.9.10.19.1.4.3.1.7 | Integer32 | read-only | Identification of modem resource allocated to call. This is the value of cmSlotIndex from CISCO-MODEM-MGMT-MIB. This value along with cpmModemPort uniquely identifies a modem. Value is -1 if call does not utilize a modem. |
| cpmNotificationGroup | 1.3.6.1.4.1.9.10.19.3.2.10 | The collection of notifications | ||
| cpmNotificationGroupRev1 | 1.3.6.1.4.1.9.10.19.3.2.13 | The collection of notifications | ||
| cpmNotifications | 1.3.6.1.4.1.9.10.19.2.0 | |||
| C32 cpmOutOctets | 1.3.6.1.4.1.9.10.19.1.1.1.1.10 | Counter32 | read-only | The total number of octets transmitted on this DS0 for data calls (cpmDS0CallType has the value 'analog(3)' or 'digital(4)' or 'v110(5)' or 'v120(6)'). All the transmitted 'raw' octets are counted, including any protocol headers which may or may not be present, depending on the service type of data call. |
| C32 cpmOutPackets | 1.3.6.1.4.1.9.10.19.1.1.1.1.12 | Counter32 | read-only | The total number of packets transmitted on this DS0 for data calls (cpmDS0CallTyp has the value 'analog(3)' or 'digital(4)' or 'v110(5)' or 'v120(6)'). |
| G32 cpmPPPCalls | 1.3.6.1.4.1.9.10.19.1.1.5 | Gauge32 | read-only | The current number of active PPP calls received by the managed device |
| STR cpmRemotePhoneNumber | 1.3.6.1.4.1.9.10.19.1.4.3.1.13 | DisplayString | read-only | The remote telephone number. For a call into the device, this is the originating number. For a call out of the device, this is the dialed number. If not available the string length is zero. |
| G32 cpmSW56CfgBChannelsInUse | 1.3.6.1.4.1.9.10.19.1.1.10 | Gauge32 | read-only | The number of configured SW56 B-Channels that are currently occupied by Digital calls. |
| cpmSystemGroup | 1.3.6.1.4.1.9.10.19.3.2.8 | A collection of objects providing statistics aggregation for the entire system. | ||
| TIK cpmTimeInUse | 1.3.6.1.4.1.9.10.19.1.1.1.1.8 | TimeTicks | read-only | The amount of time that this DS0 has been in use. This is computed by summing up the call durations of all past calls that have occupied this DS0. |
| C32 cpmTotalISDNSyncPPPCalls | 1.3.6.1.4.1.9.10.19.1.1.18 | Counter32 | read-only | The total number of ISDN-sync PPP calls received by the managed device since last system re-initialization. |
| I32 cpmTTYNumber | 1.3.6.1.4.1.9.10.19.1.4.3.1.15 | Integer32 | read-only | The TTY number associated with this call. This information comes from the IOS 'show line' command. |
| STR cpmUserID | 1.3.6.1.4.1.9.10.19.1.4.3.1.4 | DisplayString | read-only | The User login ID or zero length string if unavailable. This object comes directly from IOS. |
| IP cpmUserIpAddr | 1.3.6.1.4.1.9.10.19.1.4.3.1.5 | IpAddress | read-only | The IP address of the call or 0.0.0.0 if unavailable. This object comes directly from IOS. |
| G32 cpmV110Calls | 1.3.6.1.4.1.9.10.19.1.1.7 | Gauge32 | read-only | The current number of active V.110 calls received by the managed device |
| G32 cpmV120Calls | 1.3.6.1.4.1.9.10.19.1.1.6 | Gauge32 | read-only | The current number of active V.120 calls received by the managed device |
| cPopMgmtMIBNotificationPrefix | 1.3.6.1.4.1.9.10.19.2 |
RFC description
Cisco Point-of-Presence (POP) management MIB; vendor-private MIB for managing large-scale Cisco service provider infrastructure.
Start monitoring Cisco dial-access server / Point-of-Presence (PoP) concentrator with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.