| OID symbolic | OID numeric | Type | Access | Description |
|---|
| cmplsTeExtStdMIB | 1.3.6.1.4.1.9.10.146 | | | Copyright (c) 2012 IETF Trust and the persons identified
as the document authors. All rights reserved.
This MIB module contains generic object definitions for
MPLS Traffic Engineering in transport networks.This module is a
cisco-ized version of the IETF draft:
draft-ietf-mpls-tp-te-mib-03 |
| cmplsTeExtNotifications | 1.3.6.1.4.1.9.10.146.0 | | | |
| cmplsTeExtObjects | 1.3.6.1.4.1.9.10.146.1 | | | |
| cmplsNodeConfigTable | 1.3.6.1.4.1.9.10.146.1.1 | | not-accessible | This table allows the administrator to map a node or
LSR Identifier (IP compatible [Global_Node_ID] or ICC)
with a local identifier.
This table is created to reuse the existing
mplsTunnelTable for MPLS based transport network
tunnels also.
Since the MPLS tunnel's Ingress/Egress LSR identifiers'
size (Unsigned32) value is not compatible for
MPLS-TP tunnel i.e. Global_Node_Id of size 8 bytes and
ICC of size 6 bytes, there exists a need to map the
Global_Node_ID or ICC with the local identifier of size
4 bytes (Unsigned32) value in order
to index (Ingress/Egress LSR identifier)
the existing mplsTunnelTable. |
| cmplsNodeConfigEntry | 1.3.6.1.4.1.9.10.146.1.1.1 | | not-accessible | An entry in this table represents a mapping
identification for the operator or service provider
with node or LSR.
As per [RFC6370], this mapping is
represented as Global_Node_ID or ICC.
Note: Each entry in this table should have a unique
Global_ID and Node_ID combination. |
| CMP cmplsNodeConfigLocalId | 1.3.6.1.4.1.9.10.146.1.1.1.1 | CMplsLocalId | not-accessible | This object allows the administrator to assign a unique
local identifier to map Global_Node_ID or ICC. |
| CMP cmplsNodeConfigGlobalId | 1.3.6.1.4.1.9.10.146.1.1.1.2 | CMplsGlobalId | read-write | This object indicates the Global Operator Identifier.
This object value should be zero when
mplsNodeConfigIccId is configured with non-null value. |
| CMP cmplsNodeConfigNodeId | 1.3.6.1.4.1.9.10.146.1.1.1.3 | CMplsNodeId | read-write | This object indicates the Node_ID within the operator.
This object value should be zero when mplsNodeConfigIccId
is configured with non-null value. |
| CMP cmplsNodeConfigIccId | 1.3.6.1.4.1.9.10.146.1.1.1.4 | CMplsIccId | read-write | This object allows the operator or service provider to
configure a unique MPLS-TP ITU-T Carrier Code (ICC)
either for Ingress ID or Egress ID.
This object value should be zero when
mplsNodeConfigGlobalId and mplsNodeConfigNodeId are
assigned with non-zero value. |
| ROW cmplsNodeConfigRowStatus | 1.3.6.1.4.1.9.10.146.1.1.1.5 | RowStatus | read-write | This object allows the administrator to create, modify,
and/or delete a row in this table. |
| STO cmplsNodeConfigStorageType | 1.3.6.1.4.1.9.10.146.1.1.1.6 | StorageType | read-write | This variable indicates the storage type for this
object.
Conceptual rows having the value 'permanent'
need not allow write-access to any columnar
objects in the row. |
| cmplsNodeIpMapTable | 1.3.6.1.4.1.9.10.146.1.2 | | not-accessible | This read-only table allows the administrator to retrieve
the local identifier for a given Global_Node_ID in an IP
compatible operator environment.
This table MAY be used in on-demand and/or proactive
OAM operations to get the Ingress/Egress LSR identifier
(Local Identifier) from Src-Global_Node_ID
or Dst-Global_Node_ID and the Ingress and Egress LSR
identifiers are used to retrieve the tunnel entry.
This table returns nothing when the associated entry
is not defined in mplsNodeConfigTable. |
| cmplsNodeIpMapEntry | 1.3.6.1.4.1.9.10.146.1.2.1 | | not-accessible | An entry in this table represents a mapping of
Global_Node_ID with the local identifier.
An entry in this table is created automatically when
the Local identifier is associated with Global_ID and
Node_Id in the mplsNodeConfigTable.
Note: Each entry in this table should have a unique
Global_ID and Node_ID combination. |
| CMP cmplsNodeIpMapGlobalId | 1.3.6.1.4.1.9.10.146.1.2.1.1 | CMplsGlobalId | not-accessible | This object indicates the Global_ID. |
| CMP cmplsNodeIpMapNodeId | 1.3.6.1.4.1.9.10.146.1.2.1.2 | CMplsNodeId | not-accessible | This object indicates the Node_ID within the
operator. |
| CMP cmplsNodeIpMapLocalId | 1.3.6.1.4.1.9.10.146.1.2.1.3 | CMplsLocalId | read-only | This object contains an IP compatible local identifier
which is defined in mplsNodeConfigTable. |
| cmplsNodeIccMapTable | 1.3.6.1.4.1.9.10.146.1.3 | | not-accessible | This read-only table allows the administrator to retrieve
the local identifier for a given ICC operator in an ICC
operator environment.
This table MAY be used in on-demand and/or proactive
OAM operations to get the Ingress/Egress LSR
identifier (Local Identifier) from Src-ICC
or Dst-ICC and the Ingress and Egress LSR
identifiers are used to retrieve the tunnel entry.
This table returns nothing when the associated entry
is not defined in mplsNodeConfigTable. |
| cmplsNodeIccMapEntry | 1.3.6.1.4.1.9.10.146.1.3.1 | | not-accessible | An entry in this table represents a mapping of ICC with
the local identifier.
An entry in this table is created automatically when
the Local identifier is associated with ICC in
the mplsNodeConfigTable. |
| CMP cmplsNodeIccMapIccId | 1.3.6.1.4.1.9.10.146.1.3.1.1 | CMplsIccId | not-accessible | This object allows the operator or service provider to
configure a unique MPLS-TP ITU-T Carrier Code (ICC)
either for Ingress or Egress LSR ID.
The ICC is a string of one to six characters, each
character being either alphabetic (i.e. A-Z) or
numeric (i.e. 0-9) characters. Alphabetic characters
in the ICC should be represented with upper case
letters. |
| CMP cmplsNodeIccMapLocalId | 1.3.6.1.4.1.9.10.146.1.3.1.2 | CMplsLocalId | read-only | This object contains an ICC based local identifier
which is defined in mplsNodeConfigTable. |
| cmplsTunnelExtTable | 1.3.6.1.4.1.9.10.146.1.4 | | not-accessible | This table represents MPLS-TP specific extensions to
mplsTunnelTable.
As per MPLS-TP Identifiers [RFC6370], LSP_ID for IP based
co-routed bidirectional tunnel,
A1-{Global_ID::Node_ID::Tunnel_Num}::Z9-{Global_ID::
Node_ID::Tunnel_Num}::LSP_Num
LSP_ID for IP based associated bidirectional tunnel,
A1-{Global_ID::Node_ID::Tunnel_Num::LSP_Num}::
Z9-{Global_ID::Node_ID::Tunnel_Num::LSP_Num}
mplsTunnelTable is reused for forming the LSP_ID
as follows,
Source Tunnel_Num is mapped with mplsTunnelIndex,
Source Node_ID is mapped with
mplsTunnelIngressLSRId, Destination Node_ID is
mapped with mplsTunnelEgressLSRId LSP_Num is mapped with
mplsTunnelInstance.
Source Global_Node_ID and/or ICC and Destination
Global_Node_ID and/or ICC are maintained in the
mplsNodeConfigTable and mplsNodeConfigLocalId is
used to create an entry in mplsTunnelTable. |
| cmplsTunnelExtEntry | 1.3.6.1.4.1.9.10.146.1.4.1 | | not-accessible | An entry in this table represents MPLS-TP
specific additional tunnel configurations. |
| NUM cmplsTunnelOppositeDirPtr | 1.3.6.1.4.1.9.10.146.1.4.1.1 | RowPointer | read-create | This object is applicable only for the bidirectional
tunnel that has the forward and reverse LSPs in the
same tunnel or in the different tunnels.
This object holds the opposite direction tunnel entry
if the bidirectional tunnel is setup by configuring two
tunnel entries in mplsTunnelTable.
The value of zeroDotZero indicates single tunnel entry
is used for bidirectional tunnel setup. |
| T/F cmplsTunnelExtOppositeDirTnlValid | 1.3.6.1.4.1.9.10.146.1.4.1.2 | TruthValue | read-create | Denotes whether or not this tunnel uses
mplsTunnelOppositeDirPtr for identifying the opposite
direction tunnel information. Note that if this variable
is set to true then the mplsTunnelOppositeDirPtr should
point to the first accessible row of the opposite
direction tunnel. |
| MPL cmplsTunnelExtDestTnlIndex | 1.3.6.1.4.1.9.10.146.1.4.1.3 | MplsTunnelIndex | read-create | This object is applicable only for the bidirectional
tunnel that has the forward and reverse LSPs in the
same tunnel or in the different tunnels.
This object holds the same value as that of the
mplsTunnelIndex of mplsTunnelEntry if the forward and
reverse LSPs are in the same tunnel. Otherwise,
this object holds the value of the other direction
associated LSP's mplsTunnelIndex from a different
tunnel.
The values of this object and the
mplsTunnelExtDestTnlLspIndex object together can be used
to identify an opposite direction LSP i.e. if the
mplsTunnelIndex and mplsTunnelInstance hold the value
for forward LSP, this object and
mplsTunnelExtDestTnlLspIndex can be used to retrieve
the reverse direction LSP and vice versa.
This object and mplsTunnelExtDestTnlLspIndex values
provide the first two indices of tunnel entry and
the remaining indices can be derived as follows,
if both the forward and reverse LSPs are present in
the same tunnel, the opposite direction LSP's Ingress
and Egress Identifier will be same for both the LSPs,
else the Ingress and Egress Identifiers should be
swapped in order to index the other direction tunnel. |
| MPL cmplsTunnelExtDestTnlLspIndex | 1.3.6.1.4.1.9.10.146.1.4.1.4 | MplsTunnelInstanceIndex | read-create | This object is applicable only for the bidirectional
tunnel that has the forward and reverse LSPs in the
same tunnel or in the different tunnels.
This object should contain different value if both the
forward and reverse LSPs present in the same tunnel.
This object can contain same value or different values
if the forward and reverse LSPs present in the different
tunnels. |
| T/F cmplsTunnelExtDestTnlValid | 1.3.6.1.4.1.9.10.146.1.4.1.5 | TruthValue | read-create | Denotes whether or not this tunnel uses
mplsTunnelExtDestTnlIndex and
mplsTunnelExtDestTnlLspIndex for identifying
the opposite direction tunnel information. Note that if
this variable is set to true then the
mplsTunnelExtDestTnlIndex and
mplsTunnelExtDestTnlLspIndex objects should have
the valid opposite direction tunnel indices. |
| cmplsTunnelReversePerfTable | 1.3.6.1.4.1.9.10.146.1.5 | | not-accessible | This table extends the mplsTunnelTable to provide
per-tunnel packet performance information for the reverse
direction of a bidirectional tunnel. It can be seen as
supplementing the mplsTunnelPerfTable, which augments the
mplsTunnelTable.
For links that do not transport packets, these packet
counters cannot be maintained. For such links, attempts
to read the objects in this table will return
noSuchInstance. |
| cmplsTunnelReversePerfEntry | 1.3.6.1.4.1.9.10.146.1.5.1 | | not-accessible | An entry in this table is created by the LSR for every
bidirectional MPLS tunnel where packets are visible to the
LSR. |
| C32 cmplsTunnelReversePerfPacketsEx | 1.3.6.1.4.1.9.10.146.1.5.1.1 | Counter32 | read-only | Number of packets forwarded on the tunnel in the reverse
direction if it is bidirectional.
This object represents the 32-bit value of the least
significant part of the 64-bit value if both
mplsTunnelReversePerfHCPackets and this object
are returned.
For links that do not transport packets, this packet
counter cannot be maintained. For such links, this value
will return noSuchInstance. |
| C64 cmplsTunnelReversePerfHCPackets | 1.3.6.1.4.1.9.10.146.1.5.1.2 | Counter64 | read-only | High-capacity counter for number of packets forwarded on
the tunnel in the reverse direction if it is
bidirectional.
For links that do not transport packets, this packet
counter cannot be maintained. For such links, this value
will return noSuchInstance. |
| C32 cmplsTunnelReversePerfErrors | 1.3.6.1.4.1.9.10.146.1.5.1.3 | Counter32 | read-only | Number of errored packets received on the tunnel in
the reverse direction if it is bidirectional. For links
that do not transport packets, this packet counter cannot
be maintained. For such links, this value will return
noSuchInstance. |
| C32 cmplsTunnelReversePerfBytes | 1.3.6.1.4.1.9.10.146.1.5.1.4 | Counter32 | read-only | Number of bytes forwarded on the tunnel in the reverse
direction if it is bidirectional.
This object represents the 32-bit value of the least
significant part of the 64-bit value if both
mplsTunnelReversePerfHCBytes and this object are returned.
For links that do not transport packets, this packet
counter cannot be maintained. For such links, this value
will return noSuchInstance. |
| C64 cmplsTunnelReversePerfHCBytes | 1.3.6.1.4.1.9.10.146.1.5.1.5 | Counter64 | read-only | High-capacity counter for number of bytes forwarded on the
tunnel in the reverse direction if it is bidirectional.
For links that do not transport packets, this packet
counter cannot be maintained. For such links, this value
will return noSuchInstance. |
| cmplsTeExtConformance | 1.3.6.1.4.1.9.10.146.2 | | | |
| cmplsTeExtGroups | 1.3.6.1.4.1.9.10.146.2.1 | | | |
| cmplsTunnelExtGroup | 1.3.6.1.4.1.9.10.146.2.1.1 | | | Necessary, but not sufficient, set of objects to
implement tunnels. In addition, depending on the
operating environment, the following groups are
mandatory. |
| cmplsTunnelExtIpOperatorGroup | 1.3.6.1.4.1.9.10.146.2.1.2 | | | Object(s) needed to implement IP compatible tunnels. |
| cmplsTunnelExtIccOperatorGroup | 1.3.6.1.4.1.9.10.146.2.1.3 | | | Object(s) needed to implement ICC based tunnels. |
| cmplsTeExtCompliances | 1.3.6.1.4.1.9.10.146.2.2 | | | |
| cmplsTeExtModuleFullCompliance | 1.3.6.1.4.1.9.10.146.2.2.1 | | | Compliance statement for agents that provide full
support the MPLS-TE-EXT-STD-MIB module. |
| cmplsTeExtModuleReadOnlyCompliance | 1.3.6.1.4.1.9.10.146.2.2.2 | | | Compliance statement for agents that provide full
support the MPLS-TE-EXT-STD-MIB module. |
