| OID symbolic | OID numeric | Type | Access | Description |
|---|
| ciscoHwModuleControlMIB | 1.3.6.1.4.1.9.9.714 | | | The MIB module providing configuration and control
information for management of hardware modules and
components on Cisco devices.
The following features are managed: bandwidth
oversubscription, clearing of HoL(Head of Line)
blocking, etc.
Bandwidth oversubscription: a group of ports are
said to be operating in bandwidth oversubscription
mode if the amount of internal forwarding fabric
bandwidth allocated to the group of ports on a
switching or routing device is less than the aggregate
maximum connection speeds of these ports.
Clearing of HoL blocking: refers to the process
in which if any port of a port group receives a
pause frame from the remote side, it will block
packet transmission on all ports of the port group
till a packet is delivered to the flow controlled
port. If the clearing of HoL blocking feature is
disabled, the device will drop packets destined
for the jammed ports and continue delivering
packets for the other ports. |
| ciscoHwModuleControlMIBNotifs | 1.3.6.1.4.1.9.9.714.0 | | | |
| ciscoHwModuleControlMIBObjects | 1.3.6.1.4.1.9.9.714.1 | | | |
| chmcOversubscription | 1.3.6.1.4.1.9.9.714.1.1 | | | |
| chmcOversubModuleTable | 1.3.6.1.4.1.9.9.714.1.1.1 | | not-accessible | Contains information for managing bandwidth
oversubscription feature for physical modules
capable of providing such feature. |
| chmcOversubModuleEntry | 1.3.6.1.4.1.9.9.714.1.1.1.1 | | not-accessible | Each entry provides management information for a
specific physical module as indicated by the value
of entPhysicalIndex, which is capable of providing
bandwidth oversubscription feature. |
| BIT chmcOversubModuleCapabilities | 1.3.6.1.4.1.9.9.714.1.1.1.1.1 | Bits | read-only | Indicates the attributes of this module with
respective to the bandwidth oversubscription feature.
oversubConfigModuleLevel(0) -
This bit is set if configuration of bandwidth
oversubscription is supported at module level.
oversubConfigPortGroupLevel(1) -
This bit is set if configuration of bandwidth
oversubscription is supported at port group
level.
clearblockConfigPortGroupLevel(2) -
This bit is set if configuration of clearing
of HoL blocking is supported at port group
level. |
| INT chmcOversubModOversubStatus | 1.3.6.1.4.1.9.9.714.1.1.1.1.2 | INTEGER | read-write | Specifies the state of the bandwidth oversubscription
feature for this module.
enabledOnAllPortGroups --
the bandwidth oversubscription feature
is enabled on all port groups of this
module.
disabledOnAllPortGroups --
the bandwidth oversubscription feature
is disabled on all port groups of this
module.
portGroupSpecific --
the bandwidth oversubscription feature
is enabled on some port groups of this
module while being disabled at the
remaining port groups of this module.
This value is a read-only value and
can not be set on any instance of
this object.
This object will only be configurable when the
instance value of chmcOversubModuleCapabilities of this
entry has the 'oversubConfigModuleLevel' bit set to 1. |
| chmcOversubPortGroupTable | 1.3.6.1.4.1.9.9.714.1.1.2 | | not-accessible | Contains information for managing bandwidth
oversubscription and clearing of HoL blocking
features for port groups of the physical modules
capable of providing bandwidth oversubscription
feature. |
| chmcOversubPortGroupEntry | 1.3.6.1.4.1.9.9.714.1.1.2.1 | | not-accessible | Each entry contains management information for a
specific port group on a specific physical module as
indicated by the value of entPhysicalIndex, which is
capable of providing bandwidth oversubscription feature. |
| U32 chmcOversubPortGrpIndex | 1.3.6.1.4.1.9.9.714.1.1.2.1.1 | Unsigned32 | not-accessible | A unique value assigned to a specific port group on a
module. |
| NUM chmcOversubPortGrpIfIndexList | 1.3.6.1.4.1.9.9.714.1.1.2.1.2 | CiscoInterfaceIndexList | read-only | Contains ifIndex values for the list of the ports in
the port group. |
| INT chmcOversubPortGrpOversubStatus | 1.3.6.1.4.1.9.9.714.1.1.2.1.3 | INTEGER | read-write | Specifies the state of the bandwidth oversubscription
feature on this port group.
other - none of the following. This value is a
read-only value and can not be set on
any instance of this object.
enabled - this port group is enabled to operate
in bandwidth oversubscription mode.
disabled - this port group is disabled to operate
in bandwidth oversubscription mode. The
first port indicated by the first four
bytes of the value of
chmcOversubPortGrpIfIndexList of this
port group will keep its administrative
status and the remaining ports of this port
group will be administratively shut down.
This object will only be configurable when the instance value
of chmcOversubModuleCapabilities for the corresponding module
has the 'oversubConfigPortGroupLevel' bit set to 1. |
| INT chmcOversubPortGrpClearBlkStatus | 1.3.6.1.4.1.9.9.714.1.1.2.1.4 | INTEGER | read-write | Specifies the state of the clearing of HoL blocking
feature on this port group.
other - none of the following. This value is a
read-only value and can not be set on
any instance of this object.
enabled - the clearing of HoL blocking feature is
enabled.
disabled - the clearing of HoL blocking feature
is disabled.
This object will only take effect when the instance value
of chmcOversubPortGrpOversubStatus of this entry is 'enabled'.
This object will only be configurable when the instance
value of chmcOversubPortGrpOversubStatus of this entry is
'enabled' and the instance value of
chmcOversubModuleCapabilities for the corresponding module
has the 'clearblockConfigPortGroupLevel' bit set to 1. |
| chmcOperationalMode | 1.3.6.1.4.1.9.9.714.1.2 | | | |
| chmcOperModePortGroupTable | 1.3.6.1.4.1.9.9.714.1.2.1 | | not-accessible | Contains information for managing operational mode
features for port groups of the physical modules
capable of providing operational mode configuration. |
| chmcOperModePortGroupEntry | 1.3.6.1.4.1.9.9.714.1.2.1.1 | | not-accessible | Each entry contains operational mode information for a
specific port group on a specific physical module as
indicated by the value of entPhysicalIndex, which is
capable of providing operational mode configuration. |
| U32 chmcOperModePortGrpIndex | 1.3.6.1.4.1.9.9.714.1.2.1.1.1 | Unsigned32 | not-accessible | A unique value assigned to a specific port group on a
module. |
| INT chmcOperModePortGrpOperMode | 1.3.6.1.4.1.9.9.714.1.2.1.1.2 | INTEGER | read-write | Specifies the operational mode of the port group.
other - none of the following. This value is a
read-only value and can not be set on
any instance of this object.
tenGigabitEthernet - this port group is operated with
10 Gigibit Ethernet port mode.
forthGigabitEthernet - this port group is operated with
40 Gigabit Ethernet port mode.
Modification on the instance value of this object may cause
the corresponding module to be reset. |
| NUM chmcOperModePortGrpIfIndexList | 1.3.6.1.4.1.9.9.714.1.2.1.1.3 | CiscoInterfaceIndexList | read-only | Contains ifIndex values for the list of the ports in
the port group. The instance value of this object may be
changed after modification on the corresponding instance
value of chmcOperModePortGrpOperMode. |
| ciscoHwModuleControlMIBConform | 1.3.6.1.4.1.9.9.714.2 | | | |
| chmcHwModuleControlMIBCompliances | 1.3.6.1.4.1.9.9.714.2.1 | | | |
| chmcHwModuleControlMIBCompliance | 1.3.6.1.4.1.9.9.714.2.1.1 | | | The compliance statement for CISCO-HW-MODULE-CONTROL-MIB. |
| chmcHwModuleControlMIBCompliance1 | 1.3.6.1.4.1.9.9.714.2.1.2 | | | The compliance statement for CISCO-HW-MODULE-CONTROL-MIB. |
| chmcHwModuleControlMIBGroups | 1.3.6.1.4.1.9.9.714.2.2 | | | |
| ciscoHmcMIBOversubBaseGroup | 1.3.6.1.4.1.9.9.714.2.2.1 | | | A collection of objects providing information about
the bandwidth oversubscription and/or clearing of HoL
blocking features for hardware modules capable of
providing such features. |
| ciscoHmcMIBOversubPgClearBlkGrp | 1.3.6.1.4.1.9.9.714.2.2.2 | | | A collection of objects describing the clearing
of HoL blocking support at port group level for
each hardware module capable of providing such
feature. |
| ciscoHmcMIBOperModeGroup | 1.3.6.1.4.1.9.9.714.2.2.3 | | | A collection of objects providing the operational
mode information at port group level for each
physical module capable of providing such feature. |
