| OID symbolic | OID numeric | Type | Access | Description |
|---|
| ciscoDocsRemoteQueryMIB | 1.3.6.1.4.1.9.10.59 | | | This MIB module provides the management of
the Cisco Cable Modem Termination Systems
(CMTS) Remote Query feature.
This feature, implemented on a CMTS, facilitates
SNMP polling of remote cable modems (CMs).
This MIB includes the configuration and
status objects of the CMTS CM Poller and
remote CMs that polled by the CMTS CM Poller |
| ciscoDocsRemQueryMIBObjects | 1.3.6.1.4.1.9.10.59.1 | | | |
| cdrqPoller | 1.3.6.1.4.1.9.10.59.1.1 | | | |
| T/F cdrqCmtsCmPollerEnable | 1.3.6.1.4.1.9.10.59.1.1.1 | TruthValue | read-write | An indication of whether the CMTS CM Poller is running.
When the poller is enabled, it polls the remote CMs
periodically specified in the cdrqCmtsCmPollerInterval
mib object.
cdrqCmtsCmPollerInterval and cdrqCmtsCmPollerCommunity
need to have valid values in order to be able to set
cdrqCmtsCmPollerEnable to TRUE.
The operation can be expensive depending on how many CMs
that the poller would be polling. It is suggested to
have it disabled when not needed. |
| NUM cdrqCmtsCmPollerInterval | 1.3.6.1.4.1.9.10.59.1.1.2 | TimeInterval | read-write | An interval between two polling cycles of the CMTS CM
Poller.
The poller will not start the next cycle until it
finished polling for the last CM , even though the
time has expired. If the cdrqCmtsCmPollerInterval is
too small with a large number of CMs, the poller would
tie up the CPU and resources and possibly degrade the
system's performance.
Any change in the cdrqCmtsCmPollerInterval will not
be reflected if the poller has already been enabled.
User cannot set cdrqCmtsCmPollerInterval to 0 but
will read 0 when CMTS is first restarted and remote-query
is not configured. Once poller is configured,
cdrqCmtsCmPollerInterval will retain the value even if
poller is later disabled |
| SNM cdrqCmtsCmPollerContextEngineID | 1.3.6.1.4.1.9.10.59.1.1.4 | SnmpEngineID | read-write | The contextEngineID indicating the location of the
context in which management information is accessed
when using the user name specified by the
corresponding instance of cdrqCmtsCmPollerCommunity.
This object is implemented to support SNMPv3 |
| STR cdrqCmtsCmPollerContextName | 1.3.6.1.4.1.9.10.59.1.1.5 | SnmpAdminString | read-write | The context in which management information is accessed
when using the user name specified by the
corresponding instance of cdrqCmtsCmPollerCommunity.
This object is implemented to support SNMPv3 |
| TIM cdrqCmtsCmPollerStartTime | 1.3.6.1.4.1.9.10.59.1.1.6 | TimeStamp | read-only | The value of sysUpTime when the last polling cycle
started.
cdrqCmtsCmPollerStartTime is set to 0 when the CMTS
is first restarted and doesn't get reset after the
poller is disabled. |
| TIM cdrqCmtsCmPollerStopTime | 1.3.6.1.4.1.9.10.59.1.1.7 | TimeStamp | read-only | The value of sysUpTime when the last polling cycle
finished.
cdrqCmtsCmPollerStopTime is set to 0 when the CMTS
is first restarted and doesn't get reset after the poller
is disabled. |
| cdrqCM | 1.3.6.1.4.1.9.10.59.1.2 | | | |
| cdrqCmtsCmStatusTable | 1.3.6.1.4.1.9.10.59.1.2.1 | | not-accessible | This table contains the status of the cable modems that
are polled by the CMTS CM Poller. The information will be
overwritten when a new polling cycle starts.
The removal of CM from the list or adding a new CM to the
list won't be reflected until the next polling cycle.
Depending on how many CMs that the poller is polling,
polling this table constantly can be quite expensive;
Therefore, it is best to poll upon receipt of the
cdrqCmtsCmRQDoneNotification. As a hedge against lost
notifications, periodic background polling should
be performed. Howerver, excessive polling could
degrade performance. |
| cdrqCmtsCmStatusEntry | 1.3.6.1.4.1.9.10.59.1.2.1.1 | | not-accessible | A list of the cable modem's attributes
that are polled by a CMTS. |
| TEN cdrqCmtsCmDownChannelPower | 1.3.6.1.4.1.9.10.59.1.2.1.1.1 | TenthdBmV | read-only | The CM's received power level. This object
may be set to zero if the CM does not support
power level measurement.
If the CM downstream interface is down, this object
either returns the most current value or the value of 0. |
| TEN cdrqCmtsCmStatusTxPower | 1.3.6.1.4.1.9.10.59.1.2.1.1.2 | TenthdBmV | read-only | The operational transmit power for the CM upstream
channel. |
| U32 cdrqCmtsCmUpChnlTxTimingOffset | 1.3.6.1.4.1.9.10.59.1.2.1.1.3 | Unsigned32 | read-only | A measure of the current round trip time. Used for
timing of CM upstream transmissions to ensure
synchronized arrivals at the CMTS. |
| TEN cdrqCmtsCmSigQSignalNoise | 1.3.6.1.4.1.9.10.59.1.2.1.1.4 | TenthdB | read-only | Signal/Noise ratio as perceived for the CM downstream
channel. |
| I32 cdrqCmtsCmSigQMicroreflectionsEx | 1.3.6.1.4.1.9.10.59.1.2.1.1.5 | Integer32 | read-only | Total microreflections including in-channel
response as perceived on the CM downstream,
measured in dBc below the signal level.
This object is not assumed to return an absolutely
accurate value, but is meant to give a rough indication
of microreflections received on this interface.
It is up to the implementor to provide information
as accurate as possible. |
| TIM cdrqCmtsCmPollTime | 1.3.6.1.4.1.9.10.59.1.2.1.1.6 | TimeStamp | read-only | The value of sysUpTime when this CM entry was polled.
If this value is larger than the cdrqCmtsCmPollerStopTime,
either by receiving it from the
cdrqCmtsCmRQDoneNotification or by polling the object
itself, it indicates that the status has already been
overwritten by a new polling cycle. To avoid this
to happen, the NMS can increase the cdrqCmtsCmPollInterval
so that the cdrqCmtsCmPollTime
would fall in between the cdrqCmtsCmPollerStartTime and
the cdrqCmtsCmPollerStopTime. |
| ciscoDocsRQNotificationsPrefix | 1.3.6.1.4.1.9.10.59.2 | | | |
| ciscoDocsRQNotifications | 1.3.6.1.4.1.9.10.59.2.0 | | | |
| NTF cdrqCmtsCmRQDoneNotification | 1.3.6.1.4.1.9.10.59.2.0.1 | | | This notification is sent when CMTS CM Poller
finished polling for the current cycle.
The cdrqCmtsCmPollerStartTime is the time when the
polling cycle started.
The cdrqCmtsCmPollerStopTime is the time when the
polling cycle finished. |
| ciscoDocsRemoteQueryConformance | 1.3.6.1.4.1.9.10.59.3 | | | |
| cdrqDocsRemoteQueryCompliances | 1.3.6.1.4.1.9.10.59.3.1 | | | |
| cdrqDocsRemoteQueryCompliance | 1.3.6.1.4.1.9.10.59.3.1.1 | | | The compliance statement for entities which
implement the Cisco Remote Query MIB |
| cdrqDocsRemoteQueryGroups | 1.3.6.1.4.1.9.10.59.3.2 | | | |
| cdrqPollerGroup | 1.3.6.1.4.1.9.10.59.3.2.1 | | | Group of objects implemented in Cable Modem
Termination Systems (CMTS) for configuring and
monitoring the CMTS CM Poller. |
| cdrqCMGroup | 1.3.6.1.4.1.9.10.59.3.2.2 | | | Group of objects implemented in Cable Modem
Termination Systems (CMTS) for monitoring cable
modems via CMTS CM Poller. |
| cdrqNotificationGroup | 1.3.6.1.4.1.9.10.59.3.2.3 | | | The notification which a CISCO-DOCS-REMOTE-QUERY-MIB
entity may implement. |
