CISCO-DMN-DSG-TUNING-MIB

All MIBs › CISCO-DMN-DSG-TUNING-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2012-11-19

Category: Cisco Devices, Satellite

Description: Manages satellite tuner and demodulator configuration on the Cisco DMN D9800, including frequency, symbol rate, and polarization.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-DMN-DSG-TUNING-MIB?

CISCO-DMN-DSG-TUNING-MIB manages satellite tuner and demodulator configuration on the Cisco DMN D9800 series digital satellite gateway, covering the RF tuning parameters used to lock onto a satellite transponder signal for DSG (DOCSIS Set-top Gateway) or similar broadcast delivery. The data it exposes is chiefly hardware configuration and lock-status for each active tuner: RF input selection, frequency, symbol rate, DVB-S forward error correction setting, modulation type, and orbital-position validation results. As a hardware-status MIB it lets an operator confirm a tuner is correctly tuned to the intended transponder and has successfully locked/validated the orbital position, revealing tuning failures such as a mistuned frequency or symbol-rate mismatch that would prevent signal reception. It is specific to Cisco's satellite headend hardware and does not appear to draw on general IETF standards for its RF-specific object model. It is typically deployed at cable/satellite headend facilities receiving and redistributing digital television or DOCSIS signaling via satellite links. Engineers can download the CISCO-DMN-DSG-TUNING-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-DMN-DSG-TUNING-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco DMN D9800 digital satellite gateway

Monitoring Examples

An operator walks activeTunerTable / activeTunerEntry by activeTunerIndex, checking activeTunerRFInput, activeTunerFreq, and activeTunerSymbolRate to confirm each tuner is configured for the correct transponder, along with activeTunerDVBSFEC and activeTunerModulation to validate the demodulation profile matches the broadcast source. Reading activeTuningValidateOrbPos alongside activeTuningChScan reveals whether the system has successfully validated the satellite's orbital position or is still scanning for lock. A tuner stuck in a scanning or unlocked state combined with a mismatched activeTunerSymbolRate would indicate an incorrect tuning configuration preventing signal acquisition.

What Can Be Monitored

tuner frequency and symbol rate
RF input selection
DVB-S forward error correction setting
modulation type
orbital position lock/validation status

Imported Objects

From CISCO-DMN-DSG-ROOT-MIB

ciscoDSGUtilities

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
ciscoDSGTuning	1.3.6.1.4.1.1429.2.2.5.5			Cisco DSG Tuning MIB.
activeTuning	1.3.6.1.4.1.1429.2.2.5.5.1
INT activeTuningInput	1.3.6.1.4.1.1429.2.2.5.5.1.1	INTEGER	read-write	Select Input for tuning.
INT activeTuningValidateOrbPos	1.3.6.1.4.1.1429.2.2.5.5.1.2	INTEGER	read-write	Command used to validate orbital position. Set this object to yes( 2 ) to validate Orbital position.
INT activeTuningChScan	1.3.6.1.4.1.1429.2.2.5.5.1.3	INTEGER	read-write	Channel Scan command. Setting scan( 1 ) triggers the channel scanning process.
activeTuningTable	1.3.6.1.4.1.1429.2.2.5.5.2
activeTunerTable	1.3.6.1.4.1.1429.2.2.5.5.2.1		not-accessible	Active Tuner Table.
activeTunerEntry	1.3.6.1.4.1.1429.2.2.5.5.2.1.1		not-accessible	Entry for Active Tuner Table.
I32 activeTunerIndex	1.3.6.1.4.1.1429.2.2.5.5.2.1.1.1	Integer32	not-accessible	Active Tuner Index.
INT activeTunerRFInput	1.3.6.1.4.1.1429.2.2.5.5.2.1.1.2	INTEGER	read-write	Active Tuner RF Input.
I32 activeTunerFreq	1.3.6.1.4.1.1429.2.2.5.5.2.1.1.3	Integer32	read-write	The Satellite Downlink frequency in the range of 0 to 15000000 KHz in steps of 1 KHz.
I32 activeTunerSymbolRate	1.3.6.1.4.1.1429.2.2.5.5.2.1.1.4	Integer32	read-write	Data rate on the transport stream in millions of symbols per second. Range is from 10000 to 450000 hectoSym/second in steps of 1 hectoSym/second. ( 1 hecto = 10^2 ).
INT activeTunerDVBSFEC	1.3.6.1.4.1.1429.2.2.5.5.2.1.1.5	INTEGER	read-write	Forward Error Correction Rate. For DVB-S2 modulation only auto is applicable. For DVB-S modulation all options are applicable.
INT activeTunerModulation	1.3.6.1.4.1.1429.2.2.5.5.2.1.1.6	INTEGER	read-write	Signal Modulation type.
INT activeTunerRollOff	1.3.6.1.4.1.1429.2.2.5.5.2.1.1.7	INTEGER	read-write	Alpha filtering - for DVB-S: 0.20/0.35, for DVB-S2: 0.20/0.25/0.35. Roll off with scaling factor of 1/100.
INT activeTunerIQ	1.3.6.1.4.1.1429.2.2.5.5.2.1.1.8	INTEGER	read-write	Spectrum Inversion.
activeInputTable	1.3.6.1.4.1.1429.2.2.5.5.2.2		not-accessible	Active Input Table.
activeInputEntry	1.3.6.1.4.1.1429.2.2.5.5.2.2.1		not-accessible	Entry for Active Input Table.
INT activeInputRFIndex	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.1	INTEGER	not-accessible	Selection of RF Input.
INT activeInputLNBType	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.2	INTEGER	read-write	LNB Type: C-Band/Single Ku/Dual Ku/Advanced. For simplified setup select C-Band or Ku-Band. If there is a need to configure LO, select Advanced.
I32 activeInputLNBTrim	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.3	Integer32	read-write	Low Noise Block Trim Level 1 when type is not advanced. It has a range of 0 to 15000000 KHz in steps of 1KHz.
I32 activeInputLNBTrim2	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.4	Integer32	read-write	Low Noise Block Trim Level 2 when type is not advanced. It has a range of 0 to 15000000 KHz in steps of 1KHz.
I32 activeInputLocalOscFreq1	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.5	Integer32	read-write	RW, only when LNB Type is Advanced. Local Oscillator #1 Frequency when type is advanced. It has a range of 0 to 15000000 KHz in steps of 1KHz.
I32 activeInputLocalOscFreq2	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.6	Integer32	read-write	RW, only when LNB Type is Advanced. Local Oscillator #2 Frequency when type is advanced. It has a range of 0 to 15000000 KHz in steps of 1KHz.
I32 activeInputCrossOver	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.7	Integer32	read-write	Crossover Frequency for Local Oscillator. It has a range of 0 to 15000000 KHz in steps of 1KHz.
INT activeInputLocalOscControl	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.8	INTEGER	read-write	22KHz Local Osillator Control.
I32 activeInputOrbitalPos	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.9	Integer32	read-write	Orbital location Azimuth.The range is from 0 to 3600 in steps of 1. The scaling factor is 1/10th of a degree.
INT activeInputEastWestFlag	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.10	INTEGER	read-write	RF Mapping Location East/West Flag.
INT activeInputPolarization	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.11	INTEGER	read-write	RF Mapping Polarization.
STR activeInputSatName	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.12	DisplayString	read-only	Satellite Name Matching the Orbital Position + E/W Flag. Enter Satellite/Transponder Name to fill in Azimuth and E/W Flag automatically.
I32 activeInputLastLNBConfig	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.13	Integer32	read-write	LNB configuration last applied.
INT activeInputDiSeqCEnable	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.14	INTEGER	read-write	DiSeqC On/Off.
INT activeInputDiSeqCSwitch	1.3.6.1.4.1.1429.2.2.5.5.2.2.1.15	INTEGER	read-write	DiSeqC switch selection.
lnbPowerTable	1.3.6.1.4.1.1429.2.2.5.5.2.3		not-accessible	LNB power Table.
lnbPowerEntry	1.3.6.1.4.1.1429.2.2.5.5.2.3.1		not-accessible	Entry for LNB power Table.
I32 lnbPowerIndex	1.3.6.1.4.1.1429.2.2.5.5.2.3.1.1	Integer32	not-accessible	Low Noise Block Power Index.
INT lnbPowerInput	1.3.6.1.4.1.1429.2.2.5.5.2.3.1.2	INTEGER	read-write	Low Noise Block Power Input.
INT lnbPowerControl	1.3.6.1.4.1.1429.2.2.5.5.2.3.1.3	INTEGER	read-write	Active LNB Power setting.13/18V is to control dual polarity LNB. The convention is: Horizontal-18V; Vertical-13V. Valid settings are, Off 13V ( 13V always, ignore polarity in NIT ) 18V ( 18V always, ignore polarity in NIT ) 13V-NIT ( 13V initially, over-ride by polarity in NIT ) 18V-NIT ( 18V initially, over-ride by polarity in NIT ).
INT lnbPowerStatus	1.3.6.1.4.1.1429.2.2.5.5.2.3.1.4	INTEGER	read-only	Low Noise Block Power Supply Status.
tuningStatusTable	1.3.6.1.4.1.1429.2.2.5.5.3
satSignalTable	1.3.6.1.4.1.1429.2.2.5.5.3.1		not-accessible	Satellite Signal Table.
satSignalEntry	1.3.6.1.4.1.1429.2.2.5.5.3.1.1		not-accessible	Entry for Satellite Signal Table.
I32 satSignalIndex	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.1	Integer32	not-accessible	Satellite Signal Table Index.
STR satSignalPvBer	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.2	DisplayString	read-only	Status: DVB-S Post-Viterbi Bit Error Rate.
STR satSignalQPSKBer	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.3	DisplayString	read-only	Status: Quadrature phase-shift keying ( QPSK ) Bit error rate.
STR satSignalLdpCber	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.4	DisplayString	read-only	Status: DVB-S2 Low Density Parity Check Bit Error Rate.
STR satSignalCndisp	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.5	DisplayString	read-only	Status: Carrier to Noise Ratio.
STR satSignalCnMargin	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.6	DisplayString	read-only	Status: Carrier to Noise Ratio Link Margin.
STR satSignalLevel	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.7	DisplayString	read-only	Status: Signal Level.
STR satSignalSatDishCnMargin	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.8	DisplayString	read-only	Status: SatDish CN Margin in dB Displays the margin in dB to a threshold level at which failure occurs. The range is 0dB to 10dB.
STR satSignalSatDishSigLevel	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.9	DisplayString	read-only	Status: SatDish Signal level( in dBm ) plus some kind of graphical signal level meter on the LCD (the range is -75 dBm to +-20 dBm).
STR satSignalPerDisp	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.10	DisplayString	read-only	Status: DVB-S2 Packet Error Rate.
STR satSignalAfc	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.11	DisplayString	read-only	Status: Tuner Frequency Offset. The range is from -51.0 to 51.0 in steps of 0.1 MHz.
STR satSignalUncorErrCnt	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.12	DisplayString	read-only	Status: Uncorrected Error Counter. The range is from 0 to 4294967295.
STR satSignalCorErrCnt	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.13	DisplayString	read-only	Status: DVB-S Reed-Solomon Corrected Error Counter.
INT satSignalRfLock	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.14	INTEGER	read-only	Status: RF Lock Status.
STR satSignalDnLkFreq	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.15	DisplayString	read-only	Status: Downlink Frequency in the range of 0.000000 to 15.000000 GHz in steps of 0.000001 GHz.
STR satSignalLbandFreq	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.16	DisplayString	read-only	Status: L-Band Frequency in the range of 950.000 to 2150.000 MHz in steps of 0.001 MHz.
STR satSignalSymbolRate	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.17	DisplayString	read-only	Status: Symbol Rate in the Range of 1.0000 to 45.0000 MegaSym/second in steps of 0.0001 MegaSym/second.
INT satSignalFecRate	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.18	INTEGER	read-only	Status: Forward Error Correction Rate.
INT satSignalPolarization	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.19	INTEGER	read-only	Status: Signal Polarization.
INT satSignalModulation	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.20	INTEGER	read-only	Status: Signal Modulation Type.
INT satSignalIQ	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.21	INTEGER	read-only	Status: Spectrum Inversion.
INT satSignalLnbPsStatus	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.22	INTEGER	read-only	Status: Low Noise Block Power Supply Status.
INT satSignalPilots	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.23	INTEGER	read-only	Status: Presence of Pilot Symbols.
INT satSignalLoSelect	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.24	INTEGER	read-only	Status: LO Select.
INT satSignalPolar	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.25	INTEGER	read-only	Status: Polarization.
INT satSignalClearSigErrCnt	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.26	INTEGER	read-write	Set this variable to yes( 2 ) to clear signal error counter.
STR satSignalValidateOrbPosDate	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.27	DisplayString	read-only	Status: Last Orbital Position Validate Date.
STR satSignalValidateOrbPosStat	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.28	DisplayString	read-only	Status: Orbital Position Validation Status.
INT satSignalChScanStatus	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.29	INTEGER	read-only	Channel Scanning Status :Off/Scanning/Done.
STR satSignalSigLevelRaw	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.30	DisplayString	read-only	Signal Level - RAW Register Value.
STR satSignalP1DStatus	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.31	DisplayString	read-only	P1 DSTATUS.
INT satSignalDvbS2FrameLen	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.32	INTEGER	read-only	DVB-S2 Frame Length.
STR satSignalCnMarginRaw	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.33	DisplayString	read-only	C/N Margin - RAW Register Value.
STR satSignalDvbSQpskErrCount	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.34	DisplayString	read-only	DVB-S QPSK Error Count.
STR satSignalDvbS2LdpcErrCount	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.35	DisplayString	read-only	DVB-S2 LPDC Error Count.
STR satSignalPvErrCount	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.36	DisplayString	read-only	DVB-S PV Error Count.
INT satSignalFecSyncStatus	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.37	INTEGER	read-only	FEC SYNC Status for DVB-S PV Decoder.
STR satSignalPktErrCount	1.3.6.1.4.1.1429.2.2.5.5.3.1.1.38	DisplayString	read-only	DVB-S/DVB-S2 Packet Error Count.
inputStatusTable	1.3.6.1.4.1.1429.2.2.5.5.3.2		not-accessible	Input Status Table.
inputStatusEntry	1.3.6.1.4.1.1429.2.2.5.5.3.2.1		not-accessible	Entry for Input Status Table.
I32 inputStatusIndex	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.1	Integer32	not-accessible	Status: Index for inputStatus Table.
INT inputStatusCurInput	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.2	INTEGER	read-only	Status: Current Input for D9865 only.
INT inputStatusSatLock	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.3	INTEGER	read-only	Status: Satellite Lock: No Lock/Lock+Sig/Lock-Sig.
INT inputStatusMpgIpLock	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.4	INTEGER	read-only	Signal Validity.MPEG over IP Lock.
STR inputStatusInputRate	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.5	DisplayString	read-only	Status: Input Rate in Mega bauds per second ( Mbps ). The range is from 0.000000 to 4294.967295 Mbps in steps of 0.000001 Mbps.
STR inputStatusNetworkName	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.6	DisplayString	read-only	Status: Network Name.
STR inputStatusNetworkId	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.7	DisplayString	read-only	Status: Network ID.
STR inputStatusTransportId	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.8	DisplayString	read-only	Status: Transport ID.
INT inputStatusScramblingMode	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.9	INTEGER	read-only	Status: Scrambling mode.
INT inputStatusTransportError	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.10	INTEGER	read-only	Status: Transport Error.
INT inputStatusAsiLock	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.11	INTEGER	read-only	Status: ASI Lock.
INT inputStatusAsiLinkError	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.12	INTEGER	read-only	Status: ASI Link Error.
INT inputStatusAsiPacketSize	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.13	INTEGER	read-only	Status: ASI Packet Size.
STR inputStatusLastTuneReason	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.14	DisplayString	read-only	Status: Reason for the last tune.
STR inputStatusCurD985xInput	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.15	DisplayString	read-only	Status: Current Input for all IRD models.
STR inputStatusIpiLinkStatus	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.16	DisplayString	read-only	Status: IPI Ethernet Link Status.
STR inputStatusIpiSignal	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.17	DisplayString	read-only	Status: IPI Signal Encapsulation Lock Status.
STR inputStatusIpiFecLock	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.18	DisplayString	read-only	Status: FEC Lock Status.
STR inputStatusIpiPcrLock	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.19	DisplayString	read-only	Status: Indicates if PCR is received without errors or not.
STR inputStatusIpiDelLatency	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.20	DisplayString	read-only	Status: Dejitter Buffer Latency.
IP inputStatusIpiData1SrcIP	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.21	IpAddress	read-only	Status: DATA1 Source IP Selected.
IP inputStatusIpiData2SrcIP	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.22	IpAddress	read-only	Status: DATA2 Source IP Selected.
STR inputStatusIpiData1TsType	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.23	DisplayString	read-only	Status: DATA1 Source Transport Type.
STR inputStatusIpiData2TsType	1.3.6.1.4.1.1429.2.2.5.5.3.2.1.24	DisplayString	read-only	Status: DATA2 Source Transport Type.
siRcvTable	1.3.6.1.4.1.1429.2.2.5.5.4
siRcvOptionTable	1.3.6.1.4.1.1429.2.2.5.5.4.1		not-accessible	Rcv Option Table.
siRcvOptionEntry	1.3.6.1.4.1.1429.2.2.5.5.4.1.1		not-accessible	Entry for Rcv Option Table.
I32 siRcvOptionInstance	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.1	Integer32	not-accessible	Instance for siRcvOptionTable.
INT siRcvOptionAcqMode	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.2	INTEGER	read-write	Custom Tuning Mode: Acquisition Mode.
INT siRcvOptionReacq	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.3	INTEGER	read-write	Set this variable to yes( 2 ) to reacquire signal.
I32 siRcvOptionNetID	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.4	Integer32	read-write	Network ID.
INT siRcvOptionInputSel	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.5	INTEGER	read-write	UserCfg locks to RF input set by the user and SW Map uses Orbital Position settings to select RF input. It is recommended to set Validate Orbital Position to 'Yes' for SW Mapped option.
INT siRcvOptionFreqSel	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.6	INTEGER	read-write	Custom Tuning Mode: Frequency Tuning Mode: NIT/Preset.
INT siRcvOptionServListMode	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.7	INTEGER	read-write	Custom Tuning Mode: Service List Mode: Rigorous/Degraded.
INT siRcvOptionUseBAT	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.8	INTEGER	read-only	Custom Tuning Mode:Bouquet Association Table in Service List.
INT siRcvOptionUseNIT	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.9	INTEGER	read-write	Custom Tuning Mode:Network Information Table in Service List.
INT siRcvOptionUseSDT	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.10	INTEGER	read-write	Custom Tuning Mode:Service Description Table in Service List.
INT siRcvOptionUsePAT	1.3.6.1.4.1.1429.2.2.5.5.4.1.1.11	INTEGER	read-write	Custom Tuning Mode:Program Association Table in Service List.
siRcvOptionStatusTable	1.3.6.1.4.1.1429.2.2.5.5.4.2		not-accessible	Rcv Option Status Table.
siRcvOptionStatusEntry	1.3.6.1.4.1.1429.2.2.5.5.4.2.1		not-accessible	Entry for Rcv Option Status Table.
I32 siRcvOptionStatusInstance	1.3.6.1.4.1.1429.2.2.5.5.4.2.1.1	Integer32	not-accessible	Instance of siRcv Option Status Table.
INT siRcvOptionLastChanReas	1.3.6.1.4.1.1429.2.2.5.5.4.2.1.2	INTEGER	read-only	Source of the last tuning.
STR siRcvOptionLastActivated	1.3.6.1.4.1.1429.2.2.5.5.4.2.1.3	DisplayString	read-only	Last Preset Activated number.The range is from 0 to 64.
INT siRcvOptionStatusFreqSel	1.3.6.1.4.1.1429.2.2.5.5.4.2.1.4	INTEGER	read-only	Status of Frequency tuning mode.
INT siRcvOptionStatusServListMode	1.3.6.1.4.1.1429.2.2.5.5.4.2.1.5	INTEGER	read-only	Status of Service list mode.
INT siRcvOptionStatusUseBAT	1.3.6.1.4.1.1429.2.2.5.5.4.2.1.6	INTEGER	read-only	Status of Bouquet Association Table in Service List.
INT siRcvOptionStatusUseNIT	1.3.6.1.4.1.1429.2.2.5.5.4.2.1.7	INTEGER	read-only	Status of Network Information Table in Service List.
INT siRcvOptionStatusUseSDT	1.3.6.1.4.1.1429.2.2.5.5.4.2.1.8	INTEGER	read-only	Status of Service Description Table in Service List.
INT siRcvOptionStatusUsePAT	1.3.6.1.4.1.1429.2.2.5.5.4.2.1.9	INTEGER	read-only	Status of Program Association Table in Service List.
siInfoRxTable	1.3.6.1.4.1.1429.2.2.5.5.4.3		not-accessible	Service information Receive table.
siInfoRxEntry	1.3.6.1.4.1.1429.2.2.5.5.4.3.1		not-accessible	Entry for Service Information Received.
I32 siInfoRxInstance	1.3.6.1.4.1.1429.2.2.5.5.4.3.1.1	Integer32	not-accessible	Instance of SI Info Receive table.
I32 siInfoRxIdx	1.3.6.1.4.1.1429.2.2.5.5.4.3.1.2	Integer32	not-accessible	Service Information Receive Table Index.
INT siInfoRxType	1.3.6.1.4.1.1429.2.2.5.5.4.3.1.3	INTEGER	read-only	Service Information Receive Table Type.
STR siInfoRxIDExt	1.3.6.1.4.1.1429.2.2.5.5.4.3.1.4	DisplayString	read-only	Service Information Receive Table ID Extension. The range is from 0 to 4294967295.
STR siInfoRxUid	1.3.6.1.4.1.1429.2.2.5.5.4.3.1.5	DisplayString	read-only	Service Information Receive Unique ID. The range is from 1 to 32.
INT siInfoRxStatus	1.3.6.1.4.1.1429.2.2.5.5.4.3.1.6	INTEGER	read-only	Service Information Receive Status.
STR siInfoRxVer	1.3.6.1.4.1.1429.2.2.5.5.4.3.1.7	DisplayString	read-only	Service Information Version. The range is from 0 to 4294967295.
STR siInfoRxPID	1.3.6.1.4.1.1429.2.2.5.5.4.3.1.8	DisplayString	read-only	Service Information Program ID. The range is from 0 to 8192.
STR siInfoRxSections	1.3.6.1.4.1.1429.2.2.5.5.4.3.1.9	DisplayString	read-only	Service Information Number of Sections. The range is from 0 to 4294967295.
siInfoTsTable	1.3.6.1.4.1.1429.2.2.5.5.4.4		not-accessible	Transport Stream table.
siInfoTsEntry	1.3.6.1.4.1.1429.2.2.5.5.4.4.1		not-accessible	Entry for Transport stream table.
I32 siInfoTsInstance	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.1	Integer32	not-accessible	Transport Stream Table Instance.
I32 siInfoTsIdx	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.2	Integer32	not-accessible	Service Information Transport Stream Index.
STR siInfoTsId	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.3	DisplayString	read-only	Frequency Plan: Service Information Transport Stream ID. The range is from 0 to 4294967295.
STR siInfoTsFreq	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.4	DisplayString	read-only	Frequency Plan: Service Information Frequency The range is from 0.000000 to 15.000000 GHz in steps of 0.000001 GHz.
STR siInfoTsSymRate	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.5	DisplayString	read-only	Frequency Plan: Service Information Symbol Rate. The range is from 1.0000 to 45.0000 Megasym/second in steps of 0.0001 Megasym.
STR siInfoTsOrbPosn	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.6	DisplayString	read-only	Frequency Plan: Service Information Orbital Position. The range is from 0.0 to 360.0 .
INT siInfoTsPolar	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.7	INTEGER	read-only	Frequency Plan: Service Information Polarization.
INT siInfoTsFEC	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.8	INTEGER	read-only	Frequency Plan: Service Information Forward Error Correction Rate.
INT siInfoTsModulation	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.9	INTEGER	read-only	Frequency Plan: Service Information Modulation.
STR siInfoTsOrgNetID	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.10	DisplayString	read-only	Frequency Plan: Service Information Original Network ID. The range is from 0 to 4294967295.
INT siInfoTsEastWestFlag	1.3.6.1.4.1.1429.2.2.5.5.4.4.1.11	INTEGER	read-only	Frequency Plan: Service Information East West flag.
siInfoVCInfoTable	1.3.6.1.4.1.1429.2.2.5.5.4.5		not-accessible	VC table.
siInfoVCInfoEntry	1.3.6.1.4.1.1429.2.2.5.5.4.5.1		not-accessible	Entry for VC information.
I32 siInfoVCInfoInstance	1.3.6.1.4.1.1429.2.2.5.5.4.5.1.1	Integer32	not-accessible	Virtual Channel Info table Instance.
I32 siInfoVCInfoIdx	1.3.6.1.4.1.1429.2.2.5.5.4.5.1.2	Integer32	not-accessible	Virtual Channel Info table Index.
STR siInfoVCInfoId	1.3.6.1.4.1.1429.2.2.5.5.4.5.1.3	DisplayString	read-only	Service Information VC Service ID. The range is from 0 to 4294967295.
STR siInfoVCInfoTxID	1.3.6.1.4.1.1429.2.2.5.5.4.5.1.4	DisplayString	read-only	Service Information VC Transport Stream ID. The range is from 0 to 4294967295.
STR siInfoVCInfoProgName	1.3.6.1.4.1.1429.2.2.5.5.4.5.1.5	DisplayString	read-only	Service Information VC Programme Name.
STR siInfoVCInfoPMTPID	1.3.6.1.4.1.1429.2.2.5.5.4.5.1.6	DisplayString	read-only	Service Information VC Program Map Table Program ID.
INT siInfoVCInfoCHType	1.3.6.1.4.1.1429.2.2.5.5.4.5.1.7	INTEGER	read-only	Service Type:TV service/ Radio service.
STR siInfoVCInfoECMPID	1.3.6.1.4.1.1429.2.2.5.5.4.5.1.8	DisplayString	read-only	Service Information VC Entitlement Control Message Program ID.
INT siInfoVCInfoAuthorized	1.3.6.1.4.1.1429.2.2.5.5.4.5.1.9	INTEGER	read-only	Service List: Channel Authorized: Yes/No.

RFC description

Tunes Cisco DSG (Digital Service Gateway) input status, signal processing, and capacity management.

Start monitoring Cisco digital satellite gateways with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-DMN-DSG-TUNING-MIB

What Is CISCO-DMN-DSG-TUNING-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description