| OID symbolic | OID numeric | Type | Access | Description |
|---|
| ciscoCableWidebandMIB | 1.3.6.1.4.1.9.9.479 | | | This is the MIB module for the support of Channel Bonding
Protocol for the Cable Modem Termination System (CMTS).
Wideband DOCSIS is a method of increasing downstream
bandwidth by simultaneously transmitting DOCSIS data
over multiple RF channels. This DOCSIS data is
organized as a sequence of 188-byte MPEG-TS data packets.
A Wideband CMTS (WCMTS) is a CMTS that also transmits
Wideband MPEG-TS packets.
An Edge QAM (Quadrature Amplitude Modulation) device is one
which provides the QAM and used to couple the Wideband MPEG-TS
packet onto the HFC plant.
A Wideband Cable Modem (WCM) is a CableModem (CM) that
is able to receive Wideband MPEG-TS packets.
A wideband channel or Bonded Group (BG) is a logical
grouping of one or more physical RF channels over which
MPEG-TS packets are carried. Wideband channel carries DOCSIS
bonded packets encapsulated in MPEG-TS packets from a
WCMTS to one or more WCMs.
Packets outgoing from WCMTS to the WCM are formatted with
the DOCSIS Header. The DOCSIS packets are then formatted into
MPEG-TS data packets. These are 188 byte MPEG packets
containing the DOCSIS information.
Within DOCSIS Header of the WB Channel there is an extended
header called, DOCSIS Bonding Extended Header, the format of
which is shown below:
--------------------------------------------------------
| ---------------------------------------------------- |
| | TYPE | LEN | BSID | SEQ |
| ---------------------------------------------------- |
| | byte 0 | byte 1-2 | byte 3-4 |
|--------------------------------------------------------|
DOCSIS Bonding Extended Header
BSID is the Bonding Service IDentifier, it defines a sequence
number for a Wideband channel. It is used by the WCM to
re-sequence packets received over downstream channels to
maintain packet order. SEQ is per service flow sequence number.
Whereas TYPE is the type of the Bonding Extended Header and LEN
specifies its length.
A Narrowband Channel is a standard DOCSIS downstream channel
which contains exactly one RF channel.
The wideband protocol utilizes the existing narrowband
downstream channel for carrying the MAC management and
signaling messages and the associated narrowband upstream
for return data traffic and signaling.
The channel bonding protocol supports multiple wideband
bonded groups. This will allow the WCM to listen to multiple
bonded groups at the same time. This would support (for example)
multicast video being sent to a CPE device on the LAN side of
the WCM in addition to standard DOCSIS data.
Channel Bonding allows two types of Bonding Group (BG) interfaces.
These are Secondary BG interface and non-Secondary BG
interface. The Secondary BG interfaces will carry the multicast
traffic, whereas, the non-Secondary BG interface will carry the
non-multicast traffic.
This MIB also allows for configuration of the RF channels
on the WCMTS, as well as the association between the RF and
narrowband downstream channels with the BG channel.
Fiber Node is an optical node which terminates the fiber based
downstream signal as an electrical signal onto a coaxial RF cable.
DEPI: Downstream external physical interface.
TSID: MPEG2 Transport Stream ID.
SFP: Small Form-Factor Pluggable. |
| ciscoCableWidebandMIBNotifs | 1.3.6.1.4.1.9.9.479.0 | | | |
| NTF ccwbSFPLinkDownNotification | 1.3.6.1.4.1.9.9.479.0.1 | | | This notification is generated when link of SFP port is
lost. entPhysicalName identifies the SFP port. |
| NTF ccwbSFPLinkUpNotification | 1.3.6.1.4.1.9.9.479.0.2 | | | This notification is generated when link of SFP port is
up. entPhysicalName identifies the SFP port. |
| ciscoCableWidebandMIBObjects | 1.3.6.1.4.1.9.9.479.1 | | | |
| ccwbRFChannelTable | 1.3.6.1.4.1.9.9.479.1.1 | | not-accessible | This table contains attributes of the physical
RF channels. MPEG-TS packets are sent across RF
channels within a wideband channel.
These physical RF channels might be present on a
different system but the WCMTS entity requires
the knowledge of that system for its operation. |
| ccwbRFChannelEntry | 1.3.6.1.4.1.9.9.479.1.1.1 | | not-accessible | An entry provides a list of attributes for a single
downstream RF channel per WCMTS entity.
An entry in this table exists for each configured
RF channel on the WCMTS entity that provides the
wideband DOCSIS functionality. The index, entPhysicalIndex,
used here is the physical index of the wideband controller
card. Since RF channels are considered part of the Wideband
controller card, hence entPhysicalIndex is used for
associating RF channels. |
| U32 ccwbRFChannelNum | 1.3.6.1.4.1.9.9.479.1.1.1.1 | Unsigned32 | not-accessible | The WCMTS identification of the RF channel.
The range of this object is limited to 0-18 in the
case of annex A/256qam, and 0-23 for Annex B and C. |
| U32 ccwbRFChannelFrequency | 1.3.6.1.4.1.9.9.479.1.1.1.2 | Unsigned32 | read-create | The center of the downstream frequency associated with
this RF channel. The final downstream RF frequency
may be provided by an edge QAM device or the CMTS itself.
See the associated compliance object for a description of
valid frequencies that may be written to this object.
If the downstream frequency associated with this
RF channel is greater than the maximum value reportable
by this object then this object should report its
maximum value (1,000,000,000) and ccwbRFChannelFrequencyRev1
must be used to report the downstream frequency.
This object is deprecated and replaced by
ccwbRFChannelFrequencyRev1. |
| U32 ccwbRFChannelWidth | 1.3.6.1.4.1.9.9.479.1.1.1.3 | Unsigned32 | read-create | The bandwidth of this downstream RF channel. Most
implementations are expected to support a channel width
of 6 MHz (North America) and/or 8 MHz (Europe).
See the associated compliance object for a description of
the valid channel widths for this object. |
| INT ccwbRFChannelModulation | 1.3.6.1.4.1.9.9.479.1.1.1.4 | INTEGER | read-create | The modulation type associated with this downstream RF
channel. See the associated conformance object for write
conditions an limitations. See the DOCSIS specification
for specifics on the modulation profiles implied by qam64
qam256 and qam1024.
qam64, qam256 and qam1024 are various modulation schemes
often used in digital cable and cable modem applications.
The numbers 64/256/1024 in qam represent constellation
points, which is the measurement of qam transmission
capability, the higher the number, higher the bits that
can be transmitted. |
| INT ccwbRFChannelAnnex | 1.3.6.1.4.1.9.9.479.1.1.1.5 | INTEGER | read-create | The value of this object indicates the conformance of
the implementation to important regional cable standards.
annexA : Annex A from ITU-J83 is used.
annexB : Annex B from ITU-J83 is used.
annexC : Annex C from ITU-J83 is used. |
| C64 ccwbRFChannelMpegPktsEx | 1.3.6.1.4.1.9.9.479.1.1.1.6 | Counter64 | read-only | The number of MPEG packets transmitted on this RF
channel. |
| STO ccwbRFChannelStorageType | 1.3.6.1.4.1.9.9.479.1.1.1.7 | StorageType | read-create | The storage type for this conceptual row. |
| ROW ccwbRFChannelRowStatus | 1.3.6.1.4.1.9.9.479.1.1.1.8 | RowStatus | read-create | Controls and reflects the status of rows in this table.
It can be used for creating and deleting
entries in this table.
The ccwbRFChannelAnnex and ccwbRFChannelModulation must
be valid for a row to be created. |
| U32 ccwbRFChannelUtilization | 1.3.6.1.4.1.9.9.479.1.1.1.9 | Unsigned32 | read-only | The calculated and truncated utilization for
this RF channel over the previous complete measuring
interval. The configured duration of the measurement
intervals is defined in the ccwbRFChanUtilInterval object.
The utilization index is a percentage expressing the
ratio between bytes used to transmit data versus the
total number of bytes transmitted in the raw bandwidth
of the RF channel. |
| U32 ccwbRFChannelFrequencyRev1 | 1.3.6.1.4.1.9.9.479.1.1.1.10 | Unsigned32 | read-create | The center of the downstream frequency associated with
this RF channel. The final downstream RF frequency
may be provided by an edge QAM device or the CMTS itself.
See the associated compliance object for a description of
valid frequencies that may be written to this object. |
| ccwbRFChannelQamTable | 1.3.6.1.4.1.9.9.479.1.2 | | not-accessible | This table contains information of the external edge QAM
which provide the physical RF channels which are available
to the wideband channels. |
| ccwbRFChannelQamEntry | 1.3.6.1.4.1.9.9.479.1.2.1 | | not-accessible | An entry provides a list of attributes for a single
RF channel which can be physically present on an external
edge QAM device.
An entry in this table exists for each configured
RF channel on the WCMTS module that provides the
wideband DOCSIS functionality. |
| IPt ccwbRFChanQamIPAddressType | 1.3.6.1.4.1.9.9.479.1.2.1.1 | InetAddressType | read-create | The type of internet address. This object identifies
the internet address type specified by
ccwbRFChanQamIPAddress object. |
| IP ccwbRFChanQamIPAddress | 1.3.6.1.4.1.9.9.479.1.2.1.2 | InetAddress | read-create | The IP address of the edge QAM device or the CMTS cable
interface which provides the physical RF channel.
The IP address will be of the type represented by
object ccwbRFChanQamIPAddressType. |
| MAC ccwbRFChanQamMacAddress | 1.3.6.1.4.1.9.9.479.1.2.1.3 | MacAddress | read-create | The MAC address of the edge QAM device or next hop router
which might be present between the WCMTS and the edge QAM. |
| INE ccwbRFChanQamUdpPort | 1.3.6.1.4.1.9.9.479.1.2.1.4 | InetPortNumber | read-create | The port number on the edge QAM associated with
this RF channel. |
| U32 ccwbRFChanQamTos | 1.3.6.1.4.1.9.9.479.1.2.1.5 | Unsigned32 | read-create | The value of the TOS field in the IP header for all
Ethernet frames destined for the given RF channel. |
| U32 ccwbRFChanQamVlanId | 1.3.6.1.4.1.9.9.479.1.2.1.6 | Unsigned32 | read-create | The VLAN ID to be inserted in the Ethernet frames when
using 802.1q frames instead of normal 802.1 frames for the
given RF channel. The value of 0 indicates that 802.1 frames
are being used and is not supported in setting this object. |
| U32 ccwbRFChanQamPriorityBits | 1.3.6.1.4.1.9.9.479.1.2.1.7 | Unsigned32 | read-create | The priority bits used when inserting Ethernet 802.1q VLAN
tags into the Ethernet frames destined for a given RF
channel.
Priority Bits (0=Best effort, 1=background, 2=spare,
3=excellent effort, 4=controlled load, 5=video,
6=voice, 7=network control). |
| U32 ccwbRFChanQamDepiRemoteId | 1.3.6.1.4.1.9.9.479.1.2.1.8 | Unsigned32 | read-create | The DEPI remote ID on edge QAM associated with this RF channel. |
| STR ccwbRFChanQamDepiTunnel | 1.3.6.1.4.1.9.9.479.1.2.1.9 | SnmpAdminString | read-create | This object specifies the name of the DEPI tunnel which determines
the DEPI data session configuration associated with this RF channel. |
| U32 ccwbRFChanQamTsid | 1.3.6.1.4.1.9.9.479.1.2.1.10 | Unsigned32 | read-create | This object specifies the MPEG2 transport stream ID which is
associated with this RF channel. |
| ccwbWBtoRFMappingTable | 1.3.6.1.4.1.9.9.479.1.3 | | not-accessible | A wideband channel is a logical grouping of one or more
physical RF channels over which Wideband MPEG-TS packets
are carried.
This table contains association information of the wideband
channels to the RF channels that are available for the WCMTS. |
| ccwbWBtoRFMappingEntry | 1.3.6.1.4.1.9.9.479.1.3.1 | | not-accessible | An entry provides a list of attributes for a single
association between a wideband channel and a RF channel.
An entry in this table exists for each association
between a wideband channel and RF channel on the WCMTS.
It is indexed by the ifIndex of the wideband channel
and entPhysicalIndex and ccwbRFChannelNum which
represents the RF channel.
This object may be modified or deleted once they are
already created. |
| G32 ccwbWBtoRFBandwidth | 1.3.6.1.4.1.9.9.479.1.3.1.1 | Gauge32 | read-create | The percentage of the RF channel bandwidth allocated
for this wideband channel. |
| STO ccwbWBtoRFStorageType | 1.3.6.1.4.1.9.9.479.1.3.1.2 | StorageType | read-create | The storage type for this conceptual row. |
| ROW ccwbWBtoRFRowStatus | 1.3.6.1.4.1.9.9.479.1.3.1.3 | RowStatus | read-create | Controls and reflects the status of rows in this table.
It can be used for creating and deleting
entries in this table.
The ccwbWBtoRFBandwidth must be valid for a row to be
created. When ccwbWBtoRFRowStatus is 'active', the object
ccwbWBtoRFBandwidth can be modified. |
| ccwbWBtoNBMappingTable | 1.3.6.1.4.1.9.9.479.1.4 | | not-accessible | This table contains information of the mapping
of the wideband channels to the Narrowband channels
that are available on the WCMTS.
The wideband protocol utilizes the existing narrowband
downstream channel for carrying the MAC management and
signaling messages and the associated narrowband upstream
for return data traffic and signaling. |
| ccwbWBtoNBMappingEntry | 1.3.6.1.4.1.9.9.479.1.4.1 | | not-accessible | An entry provides a list of attributes for a
association between a wideband channel and a narrowband
channel.
An entry in this table exists for each association
between a wideband channel and narrowband channel on the
WCMTS. The valid ifType for the ifIndex used here is,
ciscoDocsCableWBDownstream(224). |
| NUM ccwbWBtoNBifIndexForNB | 1.3.6.1.4.1.9.9.479.1.4.1.1 | InterfaceIndex | not-accessible | The ifIndex of the narrowband cable interface
associated with this wideband channel. |
| STO ccwbWBtoNBStorageType | 1.3.6.1.4.1.9.9.479.1.4.1.2 | StorageType | read-create | The storage type for this conceptual row. |
| ROW ccwbWBtoNBRowStatus | 1.3.6.1.4.1.9.9.479.1.4.1.3 | RowStatus | read-create | Controls and reflects the status of rows in this table.
It can be used for creating and deleting
entries in this table. The object ccwbWBtoNBifIndexForNB
must be valid in order for row to be created. |
| ccwbWBBondGrpTable | 1.3.6.1.4.1.9.9.479.1.5 | | not-accessible | This table provides information about a
Wideband BG interface, whether its configured
to carry multicast or non-multicast traffic.
For multicast the BG interface type is
Secondary and for non-multicast its non-Secondary.
Other objects could be added to this later in
the future. |
| ccwbWBBondGrpEntry | 1.3.6.1.4.1.9.9.479.1.5.1 | | not-accessible | An entry in this table provides information
about each Wideband BG interface whose ifType is
ciscoDocsCableWBDownstream(224). |
| T/F ccwbWBBondGrpSecondary | 1.3.6.1.4.1.9.9.479.1.5.1.1 | TruthValue | read-write | This object has the value 'true(1)' if the WB
interface(BG) is Seconday and the value
'false(2)' for non-Secondary. |
| ccwbWBCmStatusTable | 1.3.6.1.4.1.9.9.479.1.6 | | not-accessible | This table contains Wideband Cable Modem(WCM) connectivity state.
A WCM connectivity state can be associated with multiple
Wideband interfaces. |
| ccwbWBCmStatusEntry | 1.3.6.1.4.1.9.9.479.1.6.1 | | not-accessible | Status information for a single Wideband Cable Modem.
An entry in this table exists for each Wideband Cable Modem
that is connected to the WCMTS. |
| INT ccwbWBCmStatusValue | 1.3.6.1.4.1.9.9.479.1.6.1.1 | INTEGER | read-only | Current WB Cable Modem connectivity state, as specified
in the RF Interface Specification. Returned status
information is the WCM status as assumed by the WCMTS,
and indicates the following events:
The enumerations are:
offline(1) : modem considered offline.
others(2) : states is in
ccwbWBCmStatusValue.
initRangingRcvd(3) : modem sent initial ranging.
initDhcpReqRcvd(4) : dhcp request received.
onlineNetAccessDisabled(5): modem registered, but network
access for the WCM is disabled.
onlineKekAssigned(6) : modem registered, BPI enabled
and KEK assigned.
onlineTekAssigned(7) : modem registered, BPI enabled
and TEK assigned.
rejectBadMic(8) : modem did attempt to register
but registration was refused
due to bad mic.
rejectBadCos(9) : modem did attempt to register
but registration was refused
due to bad COS.
kekRejected(10) : KEK modem key assignment
rejected.
tekRejected(11) : TEK modem key assignment
rejected.
online(12) : modem registered, enabled for
data.
initTftpPacketRcvd(13) : tftp packet received and option
file transfer started.
initTodRquestRcvd(14) : Time of the Day (TOD) request
received.
reset(15) : modem is resetting.
rangingInProgress(16) : initial ranging is in progress.
dhcpGotIpAddr(17) : modem has got an IP address
rejStaleConfig(18) : modem did attempt to register
but registration was refused
due to stale Config.
rejIpSpoof(19) : modem did attempt to register
but registration was refused
due to IP Spoof.
rejClassFail(20) : modem did attempt to register
but registration was refused
due to Class failure.
rejRegNack(21) : modem did attempt to register
but no acknowledgement was
received.
bpiKekExpired(22) : KEK modem key assignment
expired.
bpiTekExpired(23) : TEK modem key assignment
expired.
shutdown(24) : modem is in shutdown state.
channelChgInitRangingRcvd(25) : modem sent initial ranging
during channel change.
channelChgRangingInProgress(26) : initial ranging is in
progress during channel
change.
wbOnline(27) : Wideband modem is online.
wbOnlinePrivacy(28) : Wideband modem is online Privacy
enabled.
wbOnlineKekAssigned(29) : Wideband modem is online
and KEK assigned.
wbOnlineTekAssigned(30) : Wideband modem is online
and TEK assigned.
wbOnlineNetAccessDis(31) : Wideband modem registered but
Network access disabled.
wbKekReject(32) : KEK wideband modem key assignment
rejected.
wbTekReject(33) : TEK wideband modem key assignment
rejected.
wbNetAccessDisReject(34) : wideband modem rejected -
Net access disabled.
wbPrivacyEnabReject(35) : wideband modem rejected
Privacy enabled.
wbKekExpire(36) : KEK Wideband modem key assignment
expired.
wbTekExpire(37) : TEK wideband modem key assignment
rejected.
wbNetAccessDisExpire(38) : wideband modem expire - Network
access disabled.
wbPrivacyEnabExpire(39) : wideband modem expire - Privacy
enabled.
This ccwbWBCmStatusValue could return initRangingRcvd(3)
or rangingInProgress(16) when the ccwbWBCmStatusValue
is ranging(2).
This ccwbWBCmStatusValue will return others(2) when the
ccwbWBCmStatusValue states is either rangingAborted(3),
rangingComplete(4), and ipComplete(5).
This ccwbWBCmStatusValue could return wbonline(27), or
onlineNetAccessDisabled(5) for WCM with BPI disabled, or
onlineNetAccessDisabled(5) or onlineTekAssigned(7) for
WCM with BPI enabled, when the ccwbWBCmStatusValue
is registrationComplete(6).
This ccwbWBCmStatusValue could return either rejectBadMic(8),
rejectBadCos(9) rejStaleConfig(19) or rejRegNack(22) when
the ccwbWBCmStatusValue is accessDenied(7) for possible
reasons of cable modem registration abort.
This ccwbWBCmStatusValue could return either onlineKekAssigned(6),
kekRejected(10), tekRejected(11), or online(12) for the WCM with
BPI enabled when the ccwbWBCmStatusValue is
registeredBPIInitializing(9).
The state rejectBadCos(9) is not applicable for DOCSIS1.1 modems.
The WCMTS only needs to report states it is able to detect. |
| ccwbWBCmStatusExtTable | 1.3.6.1.4.1.9.9.479.1.7 | | not-accessible | An entry in this table exists for each Wideband
Cable Modem which links to one or more WB interface. |
| ccwbWBCmStatusExtEntry | 1.3.6.1.4.1.9.9.479.1.7.1 | | not-accessible | This entry exists for each Wideband Cable Modem(WCM)
which links to one or more WB interface. |
| I32 ccwbWBCmStatusExtIndex | 1.3.6.1.4.1.9.9.479.1.7.1.1 | Integer32 | not-accessible | The value of this object uniquely identifies an
association between a WCM and a BG. |
| NUM ccwbWBCmWBIfindex | 1.3.6.1.4.1.9.9.479.1.7.1.2 | InterfaceIndex | read-only | ifIndex of the wideband channel associated with the WCM. |
| ccwbFiberNodeDescrTable | 1.3.6.1.4.1.9.9.479.1.8 | | not-accessible | This table contains the description of a Fiber Node
on a CMTS. An entry in this table exists for each
FiberNode ID. |
| ccwbFiberNodeDescrEntry | 1.3.6.1.4.1.9.9.479.1.8.1 | | not-accessible | This entry provides the description of each fiber node
on the CMTS and it is part of the Fiber node configuration. |
| STR ccwbFiberNodeDescription | 1.3.6.1.4.1.9.9.479.1.8.1.1 | SnmpAdminString | read-create | This object contains the user configured
description string of the fiber node. |
| STO ccwbFiberNodeDescrStorageType | 1.3.6.1.4.1.9.9.479.1.8.1.2 | StorageType | read-create | The storage type for this conceptual row. |
| ROW ccwbFiberNodeDescrRowStatus | 1.3.6.1.4.1.9.9.479.1.8.1.3 | RowStatus | read-create | Controls and reflects the status of rows in this table.
It can be used for creating and deleting
entries in this table. ccwbFiberNodeDescription must
not be null in order for row to be created. |
| ccwbFiberNodeTable | 1.3.6.1.4.1.9.9.479.1.9 | | not-accessible | This table provides configuration information of each Fiber node.
It will provide topology information of each Fiber node, which
includes information such as, Narrowband and Wideband QAMs. |
| ccwbFiberNodeEntry | 1.3.6.1.4.1.9.9.479.1.9.1 | | not-accessible | An entry in this table exists for each FiberNode ID that is in use.
It uses two indices, i.e. ccwbFiberNodeID which is the
Fiber node ID, and ccwbFiberNodeGlobRFID, which is the combined
bit mask of Narrowband RF channels and Wideband
rf-ports(rf-channels). |
| U32 ccwbFiberNodeID | 1.3.6.1.4.1.9.9.479.1.9.1.1 | Unsigned32 | not-accessible | This object represents the Fiber node ID.
Each Fiber node configuration on the CMTS is
assigned a unique Fiber node ID. |
| U32 ccwbFiberNodeGlobRFID | 1.3.6.1.4.1.9.9.479.1.9.1.2 | Unsigned32 | not-accessible | This is the RF ID of both Narrowband and
Wideband QAMs(rf-channels) combined. |
| NUM ccwbFiberNodeNBIfIndx | 1.3.6.1.4.1.9.9.479.1.9.1.3 | InterfaceIndexOrZero | read-create | This object represents the Narrowband Ifindex
of the RF downstream channel which is part
of the Fiber node configuation. |
| PHY ccwbFiberNodeWBContlrPhyIndx | 1.3.6.1.4.1.9.9.479.1.9.1.4 | PhysicalIndexOrZero | read-create | This object represents the entity physical index of
Wideband controller card. This card contains the RF
port which is part of the ccwbFiberNodeGlobRFID
bit mask. A value of zero means the index is invalid.
ccwbFiberNodeWBRFPort and ccwbFiberNodeWBContlrPhyIndx
are mutually inclusive. |
| I32 ccwbFiberNodeWBRFPort | 1.3.6.1.4.1.9.9.479.1.9.1.5 | Integer32 | read-create | This object represents the RF downstream channel IDs
(rf-ports) of the wideband controller card.
Each Wideband controller can have 24 RF channels.
ccwbFiberNodeWBRFPort and ccwbFiberNodeWBContlrPhyIndx
are mutually inclusive. |
| STO ccwbFiberNodeStorageType | 1.3.6.1.4.1.9.9.479.1.9.1.6 | StorageType | read-create | The storage type for this conceptual row. |
| ROW ccwbFiberNodeRowStatus | 1.3.6.1.4.1.9.9.479.1.9.1.7 | RowStatus | read-create | Controls and reflects the status of rows in this table.
It can be used for creating and deleting
entries in this table. |
| U32 ccwbRFChanUtilInterval | 1.3.6.1.4.1.9.9.479.1.10 | Unsigned32 | read-write | The time interval in seconds over which the RF channels
utilization index is calculated. All RF channels use the
same interval.
Setting a value of zero disables utilization reporting.
This value should be persisted accross CMTS
reinitializations. |
| T/F ccwbSFPLinkTrapEnable | 1.3.6.1.4.1.9.9.479.1.11 | TruthValue | read-write | This object specifies whether ccwbSFPLinkDownNotification and
ccwbSFPLinkUpNotification are generated. |
| ciscoCableWidebandMIBConform | 1.3.6.1.4.1.9.9.479.2 | | | |
| ciscoCableWidebandMIBCompliances | 1.3.6.1.4.1.9.9.479.2.1 | | | |
| ciscoCableWidebandMIBCompliance | 1.3.6.1.4.1.9.9.479.2.1.1 | | | The compliance statement for WCMTS devices that implement
the Wideband DOCSIS feature. |
| ciscoCableWidebandMIBComplianceRev1 | 1.3.6.1.4.1.9.9.479.2.1.2 | | | The compliance statement for WCMTS devices that
implement the Wideband DOCSIS feature. |
| ciscoCableWidebandMIBComplianceRev2 | 1.3.6.1.4.1.9.9.479.2.1.3 | | | The compliance statement for WCMTS devices that
implement the Wideband DOCSIS feature. |
| ciscoCableWidebandMIBComplianceRev3 | 1.3.6.1.4.1.9.9.479.2.1.4 | | | The compliance statement for WCMTS devices that
implement the Wideband DOCSIS feature. |
| ciscoCableWidebandMIBGroups | 1.3.6.1.4.1.9.9.479.2.2 | | | |
| ccwbWidebandObjGroup | 1.3.6.1.4.1.9.9.479.2.2.1 | | | Group of objects implemented in WCMTS
providing for Wideband DOCSIS feature. |
| ccwbWidebandObjGroupSup1 | 1.3.6.1.4.1.9.9.479.2.2.2 | | | Group of objects implemented in WCMTS
for RF channel utilization calculation. |
| ccwbWidebandObjGroupRev1 | 1.3.6.1.4.1.9.9.479.2.2.3 | | | Group of objects implemented in WCMTS
providing for Wideband DOCSIS feature. |
| ccwbWidebandObjGroupSup2 | 1.3.6.1.4.1.9.9.479.2.2.4 | | | Group of objects implemented in WCMTS
for SFP Port information. |
| ccwbWidebandNotifGroup | 1.3.6.1.4.1.9.9.479.2.2.5 | | | A collection of notifications which provides
SFP linkup/linkdown state. |
