CHIPCOM-MIB

All MIBs › CHIPCOM-MIB

Category: Vendor: 3Com

Description: Manages Chipcom (3Com) switching hub configuration, port status, and LAN connectivity in enterprise campus networks.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CHIPCOM-MIB?

CHIPCOM-MIB is a legacy enterprise MIB from Chipcom (later acquired by 3Com) for managing Chipcom's Ethernet/token-ring switching hubs and LAN concentrators used in enterprise campus networks. It exposes general device-identification and diagnostic data such as product type, serial number, firmware/software version, service date, network-management (netman) configuration, and diagnostic self-test results, along with authentication-failure tracking. For hardware/software status monitoring it provides device identity (chipGenProduct, chipGenID), firmware version (chipGenVers), diagnostic self-test health (chipGenDiagnostics), and time since last configuration change (chipGenTimeLastChanged), giving administrators a basic picture of whether the hub is healthy and properly configured. As an older enterprise MIB it defines much of its own device-identity and diagnostics structure rather than relying on later standards like the Entity MIB. It is typically found in legacy enterprise campus network environments still running Chipcom/3Com switching hub hardware. Engineers can download the CHIPCOM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CHIPCOM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Chipcom (3Com) Ethernet/token-ring switching hub
LAN concentrator

Monitoring Examples

An admin polling chipGenProduct, chipGenSerial, and chipGenVers can confirm hardware model, serial number, and firmware revision for inventory purposes, while chipGenDiagnostics reports the result of onboard self-test diagnostics to catch failing hardware. chipGenTimeLastChanged indicates when the hub's configuration was last modified, and chipGenAuthFailureAddr records the address of a station that failed authentication, useful for spotting unauthorized access attempts. The chipEchoStart/chipEchoAddr/chipEchoPattern objects support an echo/loopback test used to verify connectivity to a specific address.

What Can Be Monitored

product identification and serial number
firmware/software version
diagnostic self-test results
time of last configuration change
authentication failure source address
echo/loopback connectivity test

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
DisplayString
Gauge
IpAddress
NetworkAddress
TimeTicks
enterprises

OIDs

OID symbolic	OID numeric	Type	Access	Description
alarmGroup	1.3.6.1.4.1.49.2.3.4.7
boardGroup	1.3.6.1.4.1.49.2.3.4.5
NTF chipAboveThreshd	1.3.6.1.4.1.49.0.14			A chipAboveThreshd trap indicates that a Counter or Gauge variable has exceeded its threshd. The variable which is above its threshd is the only variable in the varBind list. Its value is taken at the time the threshd calculation is performed and therefore may be greater than the actual threshd value. Another above threshd trap will not be sent until a below threshd trap is sent.
NTF chipBelowThreshd	1.3.6.1.4.1.49.0.15			A chipBelowThreshd trap indicates that a Counter or Gauge variable had exceeded its threshd but is now below its threshd. The variable which is below its threshd is the only variable in the varBind list. Its value is taken at the time the threshd calculation is performed and therefore may be less than the actual threshd value. Another below threshd trap will not be sent until an above threshd trap is sent.
chipBridge	1.3.6.1.4.1.49.2.3.6
NTF chipChange	1.3.6.1.4.1.49.0.7			A chipChange trap is used to indicate that a configuration change has occurred. The actual variables that changed are included in the variables section of the PDU.
chipcom	1.3.6.1.4.1.49
chipDownload	1.3.6.1.4.1.49.2.7
STR chipDownloadDateTime	1.3.6.1.4.1.49.2.7.3	DisplayString	read-only	The date of the last successful download in the format hh:mm day DD Mon YY
STR chipDownloadKey	1.3.6.1.4.1.49.2.7.2	DisplayString	read-write	The key code provided by your VAR. Available by calling technical support at +1 508 460 6195.
STR chipDownloadUDKSerial	1.3.6.1.4.1.49.2.7.1	DisplayString	read-write	A string representing the serial number of the Upgrade Distribution Kit.
chipEcho	1.3.6.1.4.1.49.2.2
IP chipEchoAddr	1.3.6.1.4.1.49.2.2.2	IpAddress	read-write	The IP Address to which the device will ping. The default value is the loopback address 127.0.0.1 .
INT chipEchoNumber	1.3.6.1.4.1.49.2.2.4	INTEGER	read-write	The number of ICMP echo packets (pings) to send.
INT chipEchoPattern	1.3.6.1.4.1.49.2.2.3	INTEGER	read-write	The actual pattern to be contained in the ICMP echo packet.
CTR chipEchoResponseCounts	1.3.6.1.4.1.49.2.2.6	Counter	read-only	The count of ICMP echo response packets received since the last PING was initiated.
INT chipEchoSize	1.3.6.1.4.1.49.2.2.5	INTEGER	read-write	The size of the ICMP echo packet (ping) to send when chipEchoStart is set. The valid range is between 64 and 1500 octets.
INT chipEchoStart	1.3.6.1.4.1.49.2.2.1	INTEGER	read-write	Setting chipEchoStart to startEcho(2) causes the device to begin an ICMP echo sequence using the parameters indicated by the rest of the chipEcho group.
NTF chipEnvironment	1.3.6.1.4.1.49.0.4			A chipEnvironment trap indicates a change in the concentrator's environment has occurred. The variables supplied indicate what exactly changed.
chipExperiment	1.3.6.1.4.1.49.2.4
chipExpTokenRing	1.3.6.1.4.1.49.2.4.1
NTF chipFatal	1.3.6.1.4.1.49.0.8			A chipFatal trap is used to indicate that a fatal error has occurred. This is an indication to get the unit serviced.
chipGen	1.3.6.1.4.1.49.2.1
IP chipGenAuthFailureAddr	1.3.6.1.4.1.49.2.1.8	IpAddress	read-only	The source IP Address of the last SNMP request that caused an authentication failure trap to be generated. This object is also included in the SNMP authenticationFailure trap.
INT chipGenDiagnostics	1.3.6.1.4.1.49.2.1.4	INTEGER	read-only	The result of this product's diagnostic test(s). If any test fails, this will have the failed(2) value. Note, many products do not operate after a diagnostic failure. In this case, no SNMP communication would be available.
INT chipGenID	1.3.6.1.4.1.49.2.1.6	INTEGER	read-write	A unique ID used for grouping disparate agents together. For example, a concentrator may contain multiple agents. This ID is could be assigned by the management station to identify all of these agents as being contained in the same concentrator.
IP chipGenNetman	1.3.6.1.4.1.49.2.1.3	IpAddress	read-only	The IP (source) Address of the last authenticated SNMP PDU received by this entity before this request. An IP Address of 00.00.00.00 represents the default value.
INT chipGenProduct	1.3.6.1.4.1.49.2.1.1	INTEGER	read-only	The product type represented by this agent.
STR chipGenSerial	1.3.6.1.4.1.49.2.1.5	DisplayString	read-only	The serial number of this product.
STR chipGenServiceDate	1.3.6.1.4.1.49.2.1.2	DisplayString	read-only	The date that the product was last serviced in the format yymmdd. If this date is unknown, the value of this object is '000000'.
TIK chipGenTimeLastChanged	1.3.6.1.4.1.49.2.1.9	TimeTicks	read-only	A snapshot of sysUpTime when the last trap was generated. This attribute can be used to save polling by a management station. If there have been no traps generated since the last poll, there is no need for the station to poll again.
STR chipGenVers	1.3.6.1.4.1.49.2.1.7	DisplayString	read-only	The version identifier(s) for this agent.
NTF chipHardware	1.3.6.1.4.1.49.0.5			A chipHardware trap indicates that a soft hardware failure has been detected. An example of a soft hardware failure is too many writes to non-vatile storage. This is an indication to get the unit serviced.
NTF chipHello	1.3.6.1.4.1.49.0.1			A chipHello trap is sent every minute by an agent with the hello trap enabled. The hello trap will discontinue being sent when either the agent receives an authenticate SNMP request, or after 255 minutes.
chipmib02	1.3.6.1.4.1.49.2
NTF chipPing	1.3.6.1.4.1.49.0.13			A chipPing trap is sent after the SNMP initiated PING command is completed. After the last echo request packet is sent, this trap is sent indicating the ping address, the number of requests sent, and the number of responses received at the time the trap was generated.
NTF chipPortDown	1.3.6.1.4.1.49.0.11			A chipPortDown trap indicates that a port's status has changed to an error condition. Multiple chipPortDown traps may be sent if the port's status changes from one error to another.
NTF chipPortUp	1.3.6.1.4.1.49.0.12			A chipPortUp trap indicates that a port's status has changed to a non-error (okay or warning) condition.
chipProducts	1.3.6.1.4.1.49.2.3
NTF chipSlotDown	1.3.6.1.4.1.49.0.2			This trap indicates that the module in the indicated slot is down. Usually, this trap is sent when the module has been removed. Sometimes, this trap is sent when management communications with this module have been broken. In this case, it may not be possible to distinguish between a removed and a failed module. The module type (olModType) and the module description (olModDescr) are also provided in this case.
NTF chipSlotUp	1.3.6.1.4.1.49.0.3			This trap indicates that a blade in the indicated slot is up. Usually, this trap is sent when the module is inserted into the hub. Sometimes, this trap is sent when management communications have been restored to a module where they had previously been broken. In this case, it may not be possible to distinguish between a module that has just be inserted and a module that has just the. The module type (olModType) and the module description (olModDescr) are also provided in this case.
NTF chipSoftware	1.3.6.1.4.1.49.0.6			A chipSoftware trap indicates that a soft software failure has been detected. This is an indication to get the unit serviced.
chipTFTP	1.3.6.1.4.1.49.2.6
STR chipTFTPFileName	1.3.6.1.4.1.49.2.6.4	DisplayString	read-write	The file name of the file to retrieve (tftpGet), or the name of the file to create (tftpPut).
INT chipTFTPFileType	1.3.6.1.4.1.49.2.6.5	INTEGER	read-write	The type of file image to upload/download. The file type indicates to the agent what kind of file it is receiving. flashCode(1) indicates a code upgrade of the operational proms. bootCode(2) indicates a code upgrade of the boot proms.
IP chipTFTPIpAddress	1.3.6.1.4.1.49.2.6.3	IpAddress	read-write	The IP Address of the TFTP server.
INT chipTFTPResult	1.3.6.1.4.1.49.2.6.6	INTEGER	read-only	The result of the last TFTP operation.
INT chipTFTPSlot	1.3.6.1.4.1.49.2.6.2	INTEGER	read-write	The slot number of the module that is to be involved in the TFTP transfer with the TFTP server (chipTFTPIpAddress).
INT chipTFTPStart	1.3.6.1.4.1.49.2.6.1	INTEGER	read-write	Setting chipTFTPStart to tftpGet(2) initiates a file transfer to the agent (download); tftpPut(3) initiates a file transfer to the server (upload).
NTF chipTrunkDown	1.3.6.1.4.1.49.0.9			A chipTrunkDown trap indicates that trunk's status has changed to an error condition. Multiple chipTrunkDown traps may be sent if the trunk's status changes from one error to another.
NTF chipTrunkUp	1.3.6.1.4.1.49.0.10			A chipTrunkUp trap indicates that a trunk's status has changed to a non-error (okay or warning) condition.
chipTTY	1.3.6.1.4.1.49.2.5
INT chipTTYBaud	1.3.6.1.4.1.49.2.5.2.1.2	INTEGER	read-write	The baud rate for this TTY. It should be noted that all serial ports do not support all of the above baud rates.
INT chipTTYData	1.3.6.1.4.1.49.2.5.2.1.5	INTEGER	read-write	The number of data bits for this TTY.
INT chipTTYDTR	1.3.6.1.4.1.49.2.5.2.1.8	INTEGER	read-write	This value dictates the behavior of the RS-232 Data Terminal Ready (DTR) signal at the time a session ends due to a logout, timeout, or shutdown. This is used by some modems as an indication that they should hangup. This variable is only support if the RS-232 port has a DTR signal.
chipTTYEntry	1.3.6.1.4.1.49.2.5.2.1		not-accessible	A profile of a specific TTY interface associated with this agent.
INT chipTTYIndex	1.3.6.1.4.1.49.2.5.2.1.1	INTEGER	read-only	The TTY to which this entry refers.
INT chipTTYNumber	1.3.6.1.4.1.49.2.5.1	INTEGER	read-only	The number of terminal ports on this agent product.
INT chipTTYParity	1.3.6.1.4.1.49.2.5.2.1.3	INTEGER	read-write	The parity setting for this TTY.
STR chipTTYPrompt	1.3.6.1.4.1.49.2.5.2.1.7	DisplayString	read-write	The terminal prompt to display on this TTY. NOTE: In some implementations, this is a single variable that is used by all of the terminal and telnet sessions.
INT chipTTYStop	1.3.6.1.4.1.49.2.5.2.1.4	INTEGER	read-write	The number of stop bits for this TTY.
chipTTYTable	1.3.6.1.4.1.49.2.5.2		not-accessible	A table of TTY specific information associated with this agent.
STR chipTTYTerminalType	1.3.6.1.4.1.49.2.5.2.1.9	DisplayString	read-write	A string which indicates the type of terminal that is attached to the serial port. It should be noted that the string is passed to a telnet server whenever the server issues the IAC DO TERMINAL-TYPE command (see rfc884).
INT chipTTYTimeout	1.3.6.1.4.1.49.2.5.2.1.6	INTEGER	read-write	The number of minutes to wait before this agent logs out an inactive login session on this TTY. NOTE: In some implementations, this is a single variable that is used by all of the terminal and telnet sessions.
dot1dBridge	1.3.6.1.4.1.49.2.4.14
dot5	1.3.6.1.4.1.49.2.4.1.1
emm	1.3.6.1.4.1.49.2.3.5
fmm	1.3.6.1.4.1.49.2.3.8
focus1	1.3.6.1.4.1.49.2.3.9
hardwareGroup	1.3.6.1.4.1.49.2.3.4.2
hubGroup	1.3.6.1.4.1.49.2.3.4.4
hubSysGroup	1.3.6.1.4.1.49.2.3.4.1
midnight	1.3.6.1.4.1.49.2.3.3
oebm	1.3.6.1.4.1.49.2.3.2
oeim	1.3.6.1.4.1.49.2.3.10
ol50nnMCTL	1.3.6.1.4.1.49.2.3.1.4.4.3
ol50nnMCTLModEntry	1.3.6.1.4.1.49.2.3.1.4.4.3.1.1		not-accessible	A list of information for each 50nnM-CTL module in the concentrator.
INT ol50nnMCTLModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.3.1.1.1	INTEGER	read-only	The slot number for this module.
ol50nnMCTLModTable	1.3.6.1.4.1.49.2.3.1.4.4.3.1		not-accessible	A table that contains information about each 50nnM-CTL in the concentrator. Note, current architecture will limit the number of instances to one per concentrator.
INT ol50nnMCTLModTempStatus	1.3.6.1.4.1.49.2.3.1.4.4.3.1.1.2	INTEGER	read-only	The temperature as detected by the probes on this module.
ol50nnMHCTL	1.3.6.1.4.1.49.2.3.1.4.4.33
INT ol50nnMHCTLModClockStatus	1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.3	INTEGER	read-only	The current status of the on-board clocks on this module.
INT ol50nnMHCTLModDipCh1ActCol	1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.6	INTEGER	read-only	The Ethernet channel 1 activity/collision LED configuration as indicated by this module's dip switches.
INT ol50nnMHCTLModDipCh2ActCol	1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.7	INTEGER	read-only	The Ethernet channel 2 activity/collision LED configuration as indicated by this module's dip switches.
INT ol50nnMHCTLModDipCh3ActCol	1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.8	INTEGER	read-only	The Ethernet channel 3 activity/collision LED configuration as indicated by this module's dip switches.
ol50nnMHCTLModEntry	1.3.6.1.4.1.49.2.3.1.4.4.33.1.1		not-accessible	A list of information for each 50nnM-HCTL module in the concentrator.
INT ol50nnMHCTLModOperState	1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.2	INTEGER	read-only	The operational state of the 50nnM-HCTL module. Specifically, this is an indicator of whether the 50nnM-HCTL module is providing clock signals to the backplane. An active 50nnM-HCTL module provides clock signals to the backplane while a standby 50nnM-HCTL module does not. Note that only one 50nnM-HCTL module will be active at any given time; all other 50nnM-HCTL/ 50nnMRCTL modules in the concentrator will be in standby mode.
INT ol50nnMHCTLModPDBStatus	1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.5	INTEGER	read-only	Indicates whether this 6-slot concentrator contains a power distribution board that supports powersupply redundancy.
INT ol50nnMHCTLModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.1	INTEGER	read-only	The slot number for this module. The value should be 7.
ol50nnMHCTLModTable	1.3.6.1.4.1.49.2.3.1.4.4.33.1		not-accessible	A table that contains information about each 50nnM-HCTL in the concentrator.
INT ol50nnMHCTLModTempStatus	1.3.6.1.4.1.49.2.3.1.4.4.33.1.1.4	INTEGER	read-only	The temperature as detected by the probe on this module.
ol50nnMRCTL	1.3.6.1.4.1.49.2.3.1.4.4.23
INT ol50nnMRCTLModClockStatus	1.3.6.1.4.1.49.2.3.1.4.4.23.1.1.3	INTEGER	read-only	The current status of the on-board clocks on this module.
ol50nnMRCTLModEntry	1.3.6.1.4.1.49.2.3.1.4.4.23.1.1		not-accessible	A list of information for each 50nnMRCTL module in the concentrator.
INT ol50nnMRCTLModOperState	1.3.6.1.4.1.49.2.3.1.4.4.23.1.1.2	INTEGER	read-only	The operational state of the 50nnMRCTL module. Specifically, this is an indicator of whether the 50nnMRCTL module is providing clock signals to the backplane. An active 50nnMRCTL module provides clock signals to the backplane while a standby 50nnMRCTL module does not. Note that only one 50nnMRCTL module will be active at any given time; all other 50nnMRCTL modules in the concentrator will be in standby mode.
INT ol50nnMRCTLModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.23.1.1.1	INTEGER	read-only	The slot number for this module.
ol50nnMRCTLModTable	1.3.6.1.4.1.49.2.3.1.4.4.23.1		not-accessible	A table that contains information about each 50nnMRCTL in the concentrator.
INT ol50nnMRCTLModTempStatus	1.3.6.1.4.1.49.2.3.1.4.4.23.1.1.4	INTEGER	read-only	The temperature as detected by the probe on this module.
ol51nnBEE	1.3.6.1.4.1.49.2.3.1.4.4.9
ol51nnBEEModEntry	1.3.6.1.4.1.49.2.3.1.4.4.9.1.1		not-accessible	A list of module-specific information about a specific 51nnB-EE module in the concentrator.
STR ol51nnBEEModProtocols	1.3.6.1.4.1.49.2.3.1.4.4.9.1.1.3	DisplayString	read-only	A textual description of the protocols supported by this module
INT ol51nnBEEModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.9.1.1.1	INTEGER	read-only	The slot number of this module.
OCT ol51nnBEEModStationAddr	1.3.6.1.4.1.49.2.3.1.4.4.9.1.1.2	OCTET STRING	read-only	A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1.
ol51nnBEEModTable	1.3.6.1.4.1.49.2.3.1.4.4.9.1		not-accessible	A table of module-specific information for each 51nnB-EE module in the concentrator.
INT ol51nnBEEPortDefNetwork	1.3.6.1.4.1.49.2.3.1.4.4.9.2.1.5	INTEGER	read-only	The network for this port as specified by the OEBM's non-volatile storage.
INT ol51nnBEEPortDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.9.2.1.4	INTEGER	read-only	The network for this port as specified by this port's dip switches.
ol51nnBEEPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.9.2.1		not-accessible	A list of port-specific informatoin about a specific 51nnB-EE port in the concentrator.
INT ol51nnBEEPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.9.2.1.2	INTEGER	read-only	The port number for this port within this slot.
IP ol51nnBEEPortIpAddress	1.3.6.1.4.1.49.2.3.1.4.4.9.2.1.3	IpAddress	read-only	The IP Address associated with this port.
INT ol51nnBEEPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.9.2.1.1	INTEGER	read-only	The slot number for this port's module.
ol51nnBEEPortTable	1.3.6.1.4.1.49.2.3.1.4.4.9.2		not-accessible	A table of port-specific for each port of each 51nnBEE module in the concentrator.
ol51nnIx	1.3.6.1.4.1.49.2.3.1.4.4.31
INT ol51nnIxModDipPromDefaults	1.3.6.1.4.1.49.2.3.1.4.4.31.1.1.4	INTEGER	read-only	The current module configuration with respect to default PROM values as specified by dip switches.
ol51nnIxModEntry	1.3.6.1.4.1.49.2.3.1.4.4.31.1.1		not-accessible	A list of module-specific information about a specific 51nnI-x module in the concentrator.
STR ol51nnIxModProtocols	1.3.6.1.4.1.49.2.3.1.4.4.31.1.1.5	DisplayString	read-only	A textual description of the protocols supported by this module
INT ol51nnIxModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.31.1.1.1	INTEGER	read-only	The slot number of this module.
OCT ol51nnIxModStationAddr	1.3.6.1.4.1.49.2.3.1.4.4.31.1.1.3	OCTET STRING	read-only	A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1.
INT ol51nnIxModSwType	1.3.6.1.4.1.49.2.3.1.4.4.31.1.1.2	INTEGER	read-only	The software currently loaded and executing has the module operating as a Bridge, Switch or Router.
ol51nnIxModTable	1.3.6.1.4.1.49.2.3.1.4.4.31.1		not-accessible	A table of module-specific information for each 51nnI-x module in the concentrator.
INT ol51nnIxPortDefNetwork	1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.7	INTEGER	read-only	The network for this port as specified by the OEIM's non-volatile storage.
INT ol51nnIxPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.3	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnIxPortDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.6	INTEGER	read-only	The network for this port as specified by this port's dip switches.
ol51nnIxPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.31.2.1		not-accessible	A list of port-specific information about a specific 51nnI-x port in the concentrator.
INT ol51nnIxPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.2	INTEGER	read-only	The port number for this port within this slot.
IP ol51nnIxPortIpAddress	1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.5	IpAddress	read-only	The IP Address associated with this port.
INT ol51nnIxPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.1	INTEGER	read-only	The slot number for this port's module.
INT ol51nnIxPortSTAPState	1.3.6.1.4.1.49.2.3.1.4.4.31.2.1.4	INTEGER	read-only	The current IEEE 802.1d Spanning Tree Algorithm and Protocol state (STAP) of this port.
ol51nnIxPortTable	1.3.6.1.4.1.49.2.3.1.4.4.31.2		not-accessible	A table of port-specific information for each port of each 51nnI-x module in the concentrator.
ol51nnMAUIF	1.3.6.1.4.1.49.2.3.1.4.4.12
ol51nnMAUIFModEntry	1.3.6.1.4.1.49.2.3.1.4.4.12.1.1		not-accessible	A list of module-specific information about a specific 51nnMAUIF module in the concentrator.
INT ol51nnMAUIFModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.12.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMAUIFModTable	1.3.6.1.4.1.49.2.3.1.4.4.12.1		not-accessible	A list of module-specific information associated with a particular 51nnMAUIF module in the concentrator.
INT ol51nnMAUIFPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMAUIFPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMAUIFPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMAUIFPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnMAUIFPortDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.7	INTEGER	read-only	The network indicated by the port's dip switches.
ol51nnMAUIFPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.12.2.1		not-accessible	A list of module-specific information about a specific 51nnM-AUIF port in the concentrator.
INT ol51nnMAUIFPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMAUIFPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.12.2.1.1	INTEGER	read-only	The slot number of this port's module.
ol51nnMAUIFPortTable	1.3.6.1.4.1.49.2.3.1.4.4.12.2		not-accessible	A table of port-specific information for each port of this module type.
ol51nnMAUIM	1.3.6.1.4.1.49.2.3.1.4.4.13
ol51nnMAUIMModEntry	1.3.6.1.4.1.49.2.3.1.4.4.13.1.1		not-accessible	A list of module-specific information about a specific 51nnM-AUIM module in the concentrator.
INT ol51nnMAUIMModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.13.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMAUIMModTable	1.3.6.1.4.1.49.2.3.1.4.4.13.1		not-accessible	A list of module-specific information associated with a particular 51nnM-AUIM module in the concentrator.
INT ol51nnMAUIMPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMAUIMPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMAUIMPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMAUIMPortCollision	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.10	INTEGER	read-write	The current collision configuration for this port.
INT ol51nnMAUIMPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnMAUIMPortDipCollision	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.11	INTEGER	read-only	The collision configuration for this port as indicated by the port's dip switches.
INT ol51nnMAUIMPortDipHalfStep	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.13	INTEGER	read-only	The step configuration for this port as indicated by the port's dip switches.
INT ol51nnMAUIMPortDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.7	INTEGER	read-only	The network indicated by the port's dip switches.
INT ol51nnMAUIMPortDipSQETest	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.9	INTEGER	read-only	The SQE test configuration for this port as indicated by the port's dip switches.
ol51nnMAUIMPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1		not-accessible	A list of module-specific information about a specific 51nnM-AUIM port in the concentrator.
INT ol51nnMAUIMPortHalfStep	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.12	INTEGER	read-write	The current step configuration for this port.
INT ol51nnMAUIMPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMAUIMPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.1	INTEGER	read-only	The slot number of this port's module.
INT ol51nnMAUIMPortSQETest	1.3.6.1.4.1.49.2.3.1.4.4.13.2.1.8	INTEGER	read-write	The current SQE test configuration for this port.
ol51nnMAUIMPortTable	1.3.6.1.4.1.49.2.3.1.4.4.13.2		not-accessible	A table of port-specific information for each port of this module type.
ol51nnMBNC	1.3.6.1.4.1.49.2.3.1.4.4.8
INT ol51nnMBNCModDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.8.1.1.2	INTEGER	read-only	The network indicated by the module's dip switches.
ol51nnMBNCModEntry	1.3.6.1.4.1.49.2.3.1.4.4.8.1.1		not-accessible	A module entry containing objects that describe the module level for that particular module.
INT ol51nnMBNCModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.8.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMBNCModTable	1.3.6.1.4.1.49.2.3.1.4.4.8.1		not-accessible	A list of module-specific information associated with a particular 51nnM-BNC module in the concentrator.
INT ol51nnMBNCPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.8.2.1.3	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnMBNCPortDipGround	1.3.6.1.4.1.49.2.3.1.4.4.8.2.1.5	INTEGER	read-only	The state of this port's ground as indicated by the port's dip switches.
INT ol51nnMBNCPortDipTermination	1.3.6.1.4.1.49.2.3.1.4.4.8.2.1.4	INTEGER	read-only	The state of this port's termination as indicated by the port's dip switches.
ol51nnMBNCPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.8.2.1		not-accessible	A port entry containing objects that describe this port.
INT ol51nnMBNCPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.8.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMBNCPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.8.2.1.1	INTEGER	read-only	The slot number of this port's module.
ol51nnMBNCPortTable	1.3.6.1.4.1.49.2.3.1.4.4.8.2		not-accessible	A table of port-specific information for each port of this module type.
ol51nnMFB	1.3.6.1.4.1.49.2.3.1.4.4.24
INT ol51nnMFBModDipLLW	1.3.6.1.4.1.49.2.3.1.4.4.24.1.1.4	INTEGER	read-only	The low light warning configuration indicated by this module's dip switches.
INT ol51nnMFBModDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.24.1.1.2	INTEGER	read-only	The network indicated by the module's dip switches.
ol51nnMFBModEntry	1.3.6.1.4.1.49.2.3.1.4.4.24.1.1		not-accessible	A list of module-specific information about a specific 51nnM-FB module in the concentrator.
INT ol51nnMFBModLLW	1.3.6.1.4.1.49.2.3.1.4.4.24.1.1.3	INTEGER	read-write	The current state of this module's low light warning configuration. Enabling this feature causes the module to check for low light and to issue a warning if low light is present. Disabling low light has the advantage of faster redundancy switchover in the event of a port error.
INT ol51nnMFBModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.24.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMFBModTable	1.3.6.1.4.1.49.2.3.1.4.4.24.1		not-accessible	A list of module-specific information associated with a particular 51nnM-FB module in the concentrator.
ol51nnMFBP	1.3.6.1.4.1.49.2.3.1.4.4.16
ol51nnMFBPModEntry	1.3.6.1.4.1.49.2.3.1.4.4.16.1.1		not-accessible	A list of module-specific information about a specific 51nnM-FBP module in the concentrator.
INT ol51nnMFBPModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.16.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMFBPModTable	1.3.6.1.4.1.49.2.3.1.4.4.16.1		not-accessible	A list of module-specific information associated with a particular 51nnM-FBP module in the concentrator.
INT ol51nnMFBPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMFBPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMFBPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMFBPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
ol51nnMFBPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.24.2.1		not-accessible	A list of module-specific information about a specific 51nnM-FB port in the concentrator.
INT ol51nnMFBPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMFBPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.24.2.1.1	INTEGER	read-only	The slot number of this port's module.
ol51nnMFBPortTable	1.3.6.1.4.1.49.2.3.1.4.4.24.2		not-accessible	A table of port-specific information for each port of this module type.
INT ol51nnMFBPPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMFBPPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMFBPPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMFBPPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnMFBPPortDipHipwr	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.11	INTEGER	read-only	The high power optic configuration for this port as indicated by the port's dip switches.
INT ol51nnMFBPPortDipLLW	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.9	INTEGER	read-only	The low light warning configuration indicated by this module's dip switches.
INT ol51nnMFBPPortDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.7	INTEGER	read-only	The network indicated by the port's dip switches.
ol51nnMFBPPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1		not-accessible	A list of module-specific information about a specific 51nnM-FBP port in the concentrator.
INT ol51nnMFBPPortHipwr	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.10	INTEGER	read-write	The current high power optic configuration for this port.
INT ol51nnMFBPPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMFBPPortLLW	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.8	INTEGER	read-write	The current low light warning configuration for this port.
INT ol51nnMFBPPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.16.2.1.1	INTEGER	read-only	The slot number of this port's module.
ol51nnMFBPPortTable	1.3.6.1.4.1.49.2.3.1.4.4.16.2		not-accessible	A table of port-specific information for each port of this module type.
ol51nnMFIB	1.3.6.1.4.1.49.2.3.1.4.4.5
INT ol51nnMFIBModDipLLW	1.3.6.1.4.1.49.2.3.1.4.4.5.1.1.4	INTEGER	read-only	The low light warning configuration indicated by this module's dip switches.
INT ol51nnMFIBModDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.5.1.1.2	INTEGER	read-only	The network indicated by the module's dip switches.
ol51nnMFIBModEntry	1.3.6.1.4.1.49.2.3.1.4.4.5.1.1		not-accessible	A list of module-specific information associated with a particular 51nnM-FIB module in the concentrator.
INT ol51nnMFIBModLLW	1.3.6.1.4.1.49.2.3.1.4.4.5.1.1.3	INTEGER	read-write	The current state of this module's low light warning configuration. Enabling this feature causes the module to check for low light and to issue a warning if low light is present. Disabling low light has the advantage of faster redundancy switchover in the event of a port error.
INT ol51nnMFIBModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.5.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMFIBModTable	1.3.6.1.4.1.49.2.3.1.4.4.5.1		not-accessible	A table of module-specific information for each 51nnM-FIB module in the concentrator.
INT ol51nnMFIBPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMFIBPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMFIBPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMFIBPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
ol51nnMFIBPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.5.2.1		not-accessible	A list of information about a specific port on a 51nnM-FIB module.
INT ol51nnMFIBPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMFIBPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.5.2.1.1	INTEGER	read-only	The slot number of this port's module.
ol51nnMFIBPortTable	1.3.6.1.4.1.49.2.3.1.4.4.5.2		not-accessible	A table of port-specific information for each port of each 51nnM-FIB module.
ol51nnMFL	1.3.6.1.4.1.49.2.3.1.4.4.22
INT ol51nnMFLModDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.22.1.1.2	INTEGER	read-only	The network indicated by the module's dip switches.
ol51nnMFLModEntry	1.3.6.1.4.1.49.2.3.1.4.4.22.1.1		not-accessible	A list of module-specific information associated with a particular 51nnM-FL module in the concentrator.
INT ol51nnMFLModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.22.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMFLModTable	1.3.6.1.4.1.49.2.3.1.4.4.22.1		not-accessible	A table of module-specific information for each 51nnM-FL module in the concentrator.
INT ol51nnMFLPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return invalidData error. Remote Failure Signaling (RFS), is set on connected module port to permit transmit error detection on local port. Port must be set to be RFS when connected port is set to be redundant
INT ol51nnMFLPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy.
INT ol51nnMFLPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy.
INT ol51nnMFLPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
ol51nnMFLPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.22.2.1		not-accessible	A list of information about a specific port on a 51nnMFL module.
INT ol51nnMFLPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMFLPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.22.2.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.
ol51nnMFLPortTable	1.3.6.1.4.1.49.2.3.1.4.4.22.2		not-accessible	A table of port-specific information for each port of each 51nnMFL module.
ol51nnMFP	1.3.6.1.4.1.49.2.3.1.4.4.15
ol51nnMFPModEntry	1.3.6.1.4.1.49.2.3.1.4.4.15.1.1		not-accessible	A list of module-specific information about a specific 51nnM-FP module in the concentrator.
INT ol51nnMFPModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.15.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMFPModTable	1.3.6.1.4.1.49.2.3.1.4.4.15.1		not-accessible	A list of module-specific information associated with a particular 51nnM-FP module in the concentrator.
INT ol51nnMFPPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMFPPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMFPPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMFPPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnMFPPortDipHipwr	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.11	INTEGER	read-only	The high power optic configuration for this port as indicated by the port's dip switches.
INT ol51nnMFPPortDipLLW	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.9	INTEGER	read-only	The low light warning configuration indicated by this module's dip switches.
INT ol51nnMFPPortDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.7	INTEGER	read-only	The network indicated by the port's dip switches.
ol51nnMFPPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1		not-accessible	A list of module-specific information about a specific 51nnM-FP port in the concentrator.
INT ol51nnMFPPortHipwr	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.10	INTEGER	read-write	The current high power optic configuration for this port.
INT ol51nnMFPPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMFPPortLLW	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.8	INTEGER	read-write	The current low light warning configuration for this port.
INT ol51nnMFPPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.15.2.1.1	INTEGER	read-only	The slot number of this port's module.
ol51nnMFPPortTable	1.3.6.1.4.1.49.2.3.1.4.4.15.2		not-accessible	A table of port-specific information for each port of this module type.
ol51nnMMGT	1.3.6.1.4.1.49.2.3.1.4.4.4
IP ol51nnMMGTIpAddress	1.3.6.1.4.1.49.2.3.1.4.4.4.2.1.3	IpAddress	read-only	The IP Address associated with this port.
ol51nnMMGTModEntry	1.3.6.1.4.1.49.2.3.1.4.4.4.1.1		not-accessible	A list of module information for each 51nnM-MGT module in the concentrator.
INT ol51nnMMGTModMasterPriority	1.3.6.1.4.1.49.2.3.1.4.4.4.1.1.2	INTEGER	read-write	The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive unless the reset mastership command is used.
INT ol51nnMMGTModMasterStatus	1.3.6.1.4.1.49.2.3.1.4.4.4.1.1.3	INTEGER	read-only	The mastership status of this agent.
INT ol51nnMMGTModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.4.1.1.1	INTEGER	read-only	The slot number of this module.
OCT ol51nnMMGTModStationAddr	1.3.6.1.4.1.49.2.3.1.4.4.4.1.1.4	OCTET STRING	read-only	A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1. Note that EMMs before v3.0 will have 00-00-00-00-00-00 as their station address.
ol51nnMMGTModTable	1.3.6.1.4.1.49.2.3.1.4.4.4.1		not-accessible	A table that contains module information about each 51nnM-MGT module in the concentrator.
ol51nnMMGTPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.4.2.1		not-accessible	A list of information about a specific port on a 51nnM-MGT module.
INT ol51nnMMGTPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.4.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMMGTPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.4.2.1.1	INTEGER	read-only	The slot number of this port's module.
ol51nnMMGTPortTable	1.3.6.1.4.1.49.2.3.1.4.4.4.2		not-accessible	A table of information that contains port-specific information for each port on each 51nnM-MGT module.
ol51nnMTP	1.3.6.1.4.1.49.2.3.1.4.4.7
ol51nnMTPCL	1.3.6.1.4.1.49.2.3.1.4.4.29
INT ol51nnMTPCLModAutoPartition	1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.7	INTEGER	read-write	This object holds the consecutive collision count limit value. The module goes into the auto-partition mode whenever the consecutive collision count exceeds the consecutive collision limit count.
INT ol51nnMTPCLModConn1DipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.5	INTEGER	read-only	The network indicated by the connector dip switch.
INT ol51nnMTPCLModConn1Network	1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.3	INTEGER	read-write	The network that this connector is attached to.
INT ol51nnMTPCLModConn2DipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.6	INTEGER	read-only	The network indicated by the connector dip switch.
INT ol51nnMTPCLModConn2Network	1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.4	INTEGER	read-write	The network that this connector is attached to.
ol51nnMTPCLModEntry	1.3.6.1.4.1.49.2.3.1.4.4.29.1.1		not-accessible	A list of module-specific information about a specific 51nnM-TPCL module in the concentrator.
INT ol51nnMTPCLModMonitorConn	1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.2	INTEGER	read-write	When both connectors are on the same network: Setting this object to connector-1 allows the EMM to monitor the port statistics of port 1-12 on a per-port basis, and the port statistics of port 13-24 are summed and are reported through port 13. Setting this object to connector-2 allows the EMM to monitor the port statistics of port 12-24 on a per-port basis, and the port statistics of port 1-12 are summed and are reported through port 13. Note: when the 2 connectors are on different networks, setting this object to the value connector-1 or connector-2 will not have any effect. The port counters will be cleared whenever the value of this object is changed.
INT ol51nnMTPCLModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.29.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMTPCLModTable	1.3.6.1.4.1.49.2.3.1.4.4.29.1		not-accessible	A list of module-specific information about a specific 51nnM-TPCL module in the concentrator.
INT ol51nnMTPCLPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMTPCLPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the port index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.
INT ol51nnMTPCLPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the slot index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.
INT ol51nnMTPCLPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnMTPCLPortDipLinkInteg	1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.8	INTEGER	read-only	The link integrity configuration as indicated by this dip switch.
ol51nnMTPCLPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.29.2.1		not-accessible	A list of module-specific information about a specific 51nnM-TPCL port in the concentrator.
INT ol51nnMTPCLPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMTPCLPortLinkInteg	1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.7	INTEGER	read-write	The current link integrity configuration for this port.
INT ol51nnMTPCLPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.29.2.1.1	INTEGER	read-only	The slot number of this port's module.
ol51nnMTPCLPortTable	1.3.6.1.4.1.49.2.3.1.4.4.29.2		not-accessible	A table of port-specific information for each port of this module type.
ol51nnMTPL	1.3.6.1.4.1.49.2.3.1.4.4.17
INT ol51nnMTPLModDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.17.1.1.2	INTEGER	read-only	The network indicated by the module's dip switches.
ol51nnMTPLModEntry	1.3.6.1.4.1.49.2.3.1.4.4.17.1.1		not-accessible	A list of module-specific information about a specific 51nnM-TPL module in the concentrator.
INT ol51nnMTPLModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.17.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMTPLModTable	1.3.6.1.4.1.49.2.3.1.4.4.17.1		not-accessible	A list of module-specific information associated with a particular 51nnM-TPL module in the concentrator.
INT ol51nnMTPLPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMTPLPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the port index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.
INT ol51nnMTPLPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the slot index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.
INT ol51nnMTPLPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnMTPLPortDipJabber	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.11	INTEGER	read-only	The receive jabber configuration as indicated by this module's dip switches.
INT ol51nnMTPLPortDipLinkInteg	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.8	INTEGER	read-only	The link integrity configuration as indicated by this module's dip switches.
ol51nnMTPLPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1		not-accessible	A list of module-specific information about a specific 51nnM-TPL port in the concentrator.
INT ol51nnMTPLPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMTPLPortJabber	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.10	INTEGER	read-write	The current receive jabber configuration for this port.
INT ol51nnMTPLPortLinkInteg	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.7	INTEGER	read-write	The current link integrity configuration for this port.
INT ol51nnMTPLPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.1	INTEGER	read-only	The slot number of this port's module.
INT ol51nnMTPLPortSquelch	1.3.6.1.4.1.49.2.3.1.4.4.17.2.1.9	INTEGER	read-write	The current squelch configuration for this port. See the module's user's guide for more information.
ol51nnMTPLPortTable	1.3.6.1.4.1.49.2.3.1.4.4.17.2		not-accessible	A table of port-specific information for each port of this module type.
INT ol51nnMTPModCrossover	1.3.6.1.4.1.49.2.3.1.4.4.7.1.1.3	INTEGER	read-write	The current state of this module's crossover configuration. Setting this object to uncrossed(2) allows the last port to be used to connect to another repeater. Often this feature is used to connect one 10BASE-T module to another.
INT ol51nnMTPModDipCrossover	1.3.6.1.4.1.49.2.3.1.4.4.7.1.1.4	INTEGER	read-only	The crossover configuration indicated by this module's dip switches.
INT ol51nnMTPModDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.7.1.1.2	INTEGER	read-only	The network indicated by the module's dip switches.
ol51nnMTPModEntry	1.3.6.1.4.1.49.2.3.1.4.4.7.1.1		not-accessible	A list of module-specific information about a specific 51nnM-TP module in the concentrator.
INT ol51nnMTPModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.7.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMTPModTable	1.3.6.1.4.1.49.2.3.1.4.4.7.1		not-accessible	A table of module-specific information for each 51nnM-TP module in the concentrator.
ol51nnMTPPL	1.3.6.1.4.1.49.2.3.1.4.4.18
ol51nnMTPPLModEntry	1.3.6.1.4.1.49.2.3.1.4.4.18.1.1		not-accessible	A list of module-specific information about a specific 51nnM-TPPL module in the concentrator.
INT ol51nnMTPPLModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.18.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMTPPLModTable	1.3.6.1.4.1.49.2.3.1.4.4.18.1		not-accessible	A list of module-specific information about a specific 51nnM-TPPL module in the concentrator.
INT ol51nnMTPPLPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMTPPLPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the port index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.
INT ol51nnMTPPLPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the slot index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.
INT ol51nnMTPPLPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnMTPPLPortDipJabber	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.12	INTEGER	read-only	The receive jabber configuration as indicated by this module's dip switches.
INT ol51nnMTPPLPortDipLinkInteg	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.9	INTEGER	read-only	The link integrity configuration as indicated by this module's dip switches.
INT ol51nnMTPPLPortDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.7	INTEGER	read-only	The network indicated by the port's dip switches.
ol51nnMTPPLPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1		not-accessible	A list of module-specific information about a specific 51nnM-TPPL port in the concentrator.
INT ol51nnMTPPLPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMTPPLPortJabber	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.11	INTEGER	read-write	The current receive jabber configuration for this port.
INT ol51nnMTPPLPortLinkInteg	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.8	INTEGER	read-write	The current link integrity configuration for this port.
INT ol51nnMTPPLPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.1	INTEGER	read-only	The slot number of this port's module.
INT ol51nnMTPPLPortSquelch	1.3.6.1.4.1.49.2.3.1.4.4.18.2.1.10	INTEGER	read-write	The current squelch configuration for this port. See the module's user's guide for more information.
ol51nnMTPPLPortTable	1.3.6.1.4.1.49.2.3.1.4.4.18.2		not-accessible	A table of port-specific information for each port of this module type.
INT ol51nnMTPPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMTPPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMTPPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMTPPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnMTPPortDipLinkInteg	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.8	INTEGER	read-only	The link integrity configuration as indicated by this port's dip switches.
INT ol51nnMTPPortDipSquelch	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.10	INTEGER	read-only	The port's squelch configuration as indicated by this port's dip switches.
ol51nnMTPPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1		not-accessible	A port entry containing objects that describe this port.
INT ol51nnMTPPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMTPPortLinkInteg	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.7	INTEGER	read-write	The port's link integrity configuration. Enabling link integrity configures the port to conform to the link integrity feature as specified by 10BASE-T.
INT ol51nnMTPPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.1	INTEGER	read-only	The slot number of this port's module.
INT ol51nnMTPPortSquelch	1.3.6.1.4.1.49.2.3.1.4.4.7.2.1.9	INTEGER	read-write	The port's squelch configuration. See the module's user's guide for more information.
ol51nnMTPPortTable	1.3.6.1.4.1.49.2.3.1.4.4.7.2		not-accessible	A table of port-specific information for each port of this module type.
ol51nnMTS	1.3.6.1.4.1.49.2.3.1.4.4.21
STR ol51nnMTSModCPURev	1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.7	DisplayString	read-only	The terminal server's CPU revision.
INT ol51nnMTSModDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.6	INTEGER	read-only	The network indicated by the module's dip switches.
ol51nnMTSModEntry	1.3.6.1.4.1.49.2.3.1.4.4.21.1.1		not-accessible	A list of module information for each 51nnMTS module in the concentrator.
IP ol51nnMTSModIpAddress	1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.3	IpAddress	read-only	The IP Address of the terminal terver.
STR ol51nnMTSModProtocols	1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.2	DisplayString	read-only	A textual description of the protocols supported by this module
INT ol51nnMTSModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.1	INTEGER	read-only	The slot number of this module.
OCT ol51nnMTSModStationAddr	1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.5	OCTET STRING	read-only	A 6 octet address that uniquely identifies this module. The station address is the mac address of the terminal server.
ol51nnMTSModTable	1.3.6.1.4.1.49.2.3.1.4.4.21.1		not-accessible	A table of module-specific information for each 51nnM-TS module in the concentrator.
INT ol51nnMTSModTCPPort	1.3.6.1.4.1.49.2.3.1.4.4.21.1.1.4	INTEGER	read-only	The TCP port number of the the terminal server's remote console port.
INT ol51nnMTSPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.21.2.1.3	INTEGER	read-write	The administrative state of this port.
ol51nnMTSPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.21.2.1		not-accessible	A list of information about a specific port on a 51nnMTS module.
INT ol51nnMTSPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.21.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMTSPortOperState	1.3.6.1.4.1.49.2.3.1.4.4.21.2.1.4	INTEGER	read-only	The operational mode of this port.
INT ol51nnMTSPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.21.2.1.1	INTEGER	read-only	The slot number for this port.
ol51nnMTSPortTable	1.3.6.1.4.1.49.2.3.1.4.4.21.2		not-accessible	A table of information that contains port-specific information for each port on each 51nnMTS module.
ol51nnMUTP	1.3.6.1.4.1.49.2.3.1.4.4.6
INT ol51nnMUTPModCrossover	1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.3	INTEGER	read-write	The current state of this module's crossover configuration. Setting this object to uncrossed(2) allows the last port to be used to connect to another repeater. Often this feature is used to connect one 10BASE-T module to another.
INT ol51nnMUTPModDipCrossover	1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.4	INTEGER	read-only	The crossover configuration indicated by this module's dip switches.
INT ol51nnMUTPModDipFFL	1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.6	INTEGER	read-write	The fifo fill level as indicated by this module's dip switches.
INT ol51nnMUTPModDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.2	INTEGER	read-only	The network indicated by the module's dip switches.
ol51nnMUTPModEntry	1.3.6.1.4.1.49.2.3.1.4.4.6.1.1		not-accessible	A module entry containing objects that describe the module level for that particular module.
INT ol51nnMUTPModFFL	1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.5	INTEGER	read-write	The number of bits to store in the repeater's fifo buffer. See the module user's guide for more information.
INT ol51nnMUTPModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.6.1.1.1	INTEGER	read-only	The slot number of this module.
ol51nnMUTPModTable	1.3.6.1.4.1.49.2.3.1.4.4.6.1		not-accessible	A list of module-specific information associated with a particular 51nnM-UTP module in the concentrator.
INT ol51nnMUTPPortAdminState	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.3	INTEGER	read-write	The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error.
INT ol51nnMUTPPortBuddyPort	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.5	INTEGER	read-write	The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMUTPPortBuddySlot	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.4	INTEGER	read-write	The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.
INT ol51nnMUTPPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.6	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
INT ol51nnMUTPPortDipLinkInteg	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.8	INTEGER	read-only	The link integrity configuration as indicated by this port's dip switches.
INT ol51nnMUTPPortDipSquelch	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.10	INTEGER	read-only	The port's squelch configuration as indicated by this port's dip switches.
ol51nnMUTPPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1		not-accessible	A port entry containing objects that describe this port.
INT ol51nnMUTPPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.2	INTEGER	read-only	The port number of this port.
INT ol51nnMUTPPortLinkInteg	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.7	INTEGER	read-write	The port's link integrity configuration. Enabling link integrity configures the port to conform to the link integrity feature as specified by 10BASE-T.
INT ol51nnMUTPPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.1	INTEGER	read-only	The slot number of this port's module.
INT ol51nnMUTPPortSquelch	1.3.6.1.4.1.49.2.3.1.4.4.6.2.1.9	INTEGER	read-write	The port's squelch configuration. See the module's user's guide for more information.
ol51nnMUTPPortTable	1.3.6.1.4.1.49.2.3.1.4.4.6.2		not-accessible	A table of port-specific information for each port of this module type.
ol51nnREE	1.3.6.1.4.1.49.2.3.1.4.4.11
ol51nnREEModEntry	1.3.6.1.4.1.49.2.3.1.4.4.11.1.1		not-accessible	A list of module-specific information about a specific 51nnR-EE module in the concentrator.
STR ol51nnREEModProtocols	1.3.6.1.4.1.49.2.3.1.4.4.11.1.1.3	DisplayString	read-only	A textual description of the protocols supported by this module
INT ol51nnREEModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.11.1.1.1	INTEGER	read-only	The slot number of this module.
OCT ol51nnREEModStationAddr	1.3.6.1.4.1.49.2.3.1.4.4.11.1.1.2	OCTET STRING	read-only	A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1.
ol51nnREEModTable	1.3.6.1.4.1.49.2.3.1.4.4.11.1		not-accessible	A table of module-specific information for each 51nnR-EE module in the concentrator.
INT ol51nnREEPortDefNetwork	1.3.6.1.4.1.49.2.3.1.4.4.11.2.1.5	INTEGER	read-only	The network for this port as specified by the OERM's non-volatile storage.
INT ol51nnREEPortDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.11.2.1.4	INTEGER	read-only	The network for this port as specified by this port's dip switches.
ol51nnREEPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.11.2.1		not-accessible	A list of port-specific informatoin about a specific 51nnR-EE port in the concentrator.
INT ol51nnREEPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.11.2.1.2	INTEGER	read-only	The port number of this port.
IP ol51nnREEPortIpAddress	1.3.6.1.4.1.49.2.3.1.4.4.11.2.1.3	IpAddress	read-only	The IP Address associated with this port.
INT ol51nnREEPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.11.2.1.1	INTEGER	read-only	The slot number for this port's module.
ol51nnREEPortTable	1.3.6.1.4.1.49.2.3.1.4.4.11.2		not-accessible	A table of port-specific for each port of each 51nnR-EE module in the concentrator.
ol51nnRES	1.3.6.1.4.1.49.2.3.1.4.4.10
ol51nnRESModEntry	1.3.6.1.4.1.49.2.3.1.4.4.10.1.1		not-accessible	A list of module-specific information about a specific 51nnR-ES module in the concentrator.
STR ol51nnRESModProtocols	1.3.6.1.4.1.49.2.3.1.4.4.10.1.1.3	DisplayString	read-only	A textual description of the protocols supported by this module
INT ol51nnRESModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.10.1.1.1	INTEGER	read-only	The slot number of this module.
OCT ol51nnRESModStationAddr	1.3.6.1.4.1.49.2.3.1.4.4.10.1.1.2	OCTET STRING	read-only	A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1.
ol51nnRESModTable	1.3.6.1.4.1.49.2.3.1.4.4.10.1		not-accessible	A table of module-specific information for each 51nnR-ES module in the concentrator.
INT ol51nnRESPortDefNetwork	1.3.6.1.4.1.49.2.3.1.4.4.10.2.1.5	INTEGER	read-only	The network for this port as specified by the OERM's non-volatile storage.
INT ol51nnRESPortDipNetwork	1.3.6.1.4.1.49.2.3.1.4.4.10.2.1.4	INTEGER	read-only	The network for this port as specified by this port's dip switches.
ol51nnRESPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.10.2.1		not-accessible	A list of port-specific informatoin about a specific 51nnR-ES port in the concentrator.
INT ol51nnRESPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.10.2.1.2	INTEGER	read-only	The port number for this port.
IP ol51nnRESPortIpAddress	1.3.6.1.4.1.49.2.3.1.4.4.10.2.1.3	IpAddress	read-only	The IP Address associated with this port.
INT ol51nnRESPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.10.2.1.1	INTEGER	read-only	The slot number for this port's module.
ol51nnRESPortTable	1.3.6.1.4.1.49.2.3.1.4.4.10.2		not-accessible	A table of port-specific for each port of each 51nnR-ES module in the concentrator.
ol5208MTP	1.3.6.1.4.1.49.2.3.1.4.4.14
INT ol5208MTPModBypsAdminState	1.3.6.1.4.1.49.2.3.1.4.4.14.1.1.2	INTEGER	read-write	The desired state of this module with respect to the ring. Setting this attribute to bypass(2) will cause this module to be removed from the ring that passes through the module's ring in and ring out ports.
INT ol5208MTPModBypsOperState	1.3.6.1.4.1.49.2.3.1.4.4.14.1.1.3	INTEGER	read-only	The operational state of this module with respect to the ring. If this attribute is equal to bypass(2), then the module has been removed from the ring that passes through the module's ring in and ring out ports.
INT ol5208MTPModDipCableImp	1.3.6.1.4.1.49.2.3.1.4.4.14.1.1.4	INTEGER	read-only	The setting of this module's port impedance matching, with 100 ohm corresponding to unshielded twisted pair cabling and 150 ohm corresponding to shielded twisted pair cabling. This setting is valid for all ports on this module.
ol5208MTPModEntry	1.3.6.1.4.1.49.2.3.1.4.4.14.1.1		not-accessible	A description of the 5208M-TP module attributes.
INT ol5208MTPModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.14.1.1.1	INTEGER	read-only	The slot number of this module.
ol5208MTPModTable	1.3.6.1.4.1.49.2.3.1.4.4.14.1		not-accessible	A list of module-specific information associated with a particular 5208M-TP module in the concentrator.
INT ol5208MTPPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.14.2.1.3	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
ol5208MTPPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.14.2.1		not-accessible	A description of 5208M-TP port attributes.
INT ol5208MTPPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.14.2.1.2	INTEGER	read-only	The port number of this port.
INT ol5208MTPPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.14.2.1.1	INTEGER	read-only	The slot number of this port's module.
INT ol5208MTPPortStationType	1.3.6.1.4.1.49.2.3.1.4.4.14.2.1.4	INTEGER	read-write	Determines whether the station connected to this port has a MAC address.
ol5208MTPPortTable	1.3.6.1.4.1.49.2.3.1.4.4.14.2		not-accessible	A table of port-specific information for each port of this module type.
INT ol5208MTPTrunkCableMon	1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.4	INTEGER	read-write	The cable monitor configuration for this trunk.
INT ol5208MTPTrunkDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.3	INTEGER	read-only	The state of this trunk as indicated by the trunk's dip switches.
INT ol5208MTPTrunkDipCableMon	1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.5	INTEGER	read-only	The cable monitor configuration as indicated by this trunk's dip switches.
ol5208MTPTrunkEntry	1.3.6.1.4.1.49.2.3.1.4.4.14.3.1		not-accessible	A description of 5208M-TP trunk attributes.
INT ol5208MTPTrunkExtBcnRecovery	1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.7	INTEGER	read-write	Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for trunks which connect to hubs which perform beacon recovery. This attribute is used to determine the fault domain when resolving a beaconing condition. The beacon recovery process will resolve beaconing on trunks with this attribute set to nonExists(2) before trunks with the attribute set to exists(1) are resolved. For backplane trunks, setting to a value other than notApplicable will return invalidData error. The default value is nonExists(2).
INT ol5208MTPTrunkIndex	1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.2	INTEGER	read-only	The trunk number for this trunk.
INT ol5208MTPTrunkNetMapState	1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.6	INTEGER	read-write	The map state of the copper ring-in trunk. This should be set to external for ring-in trunks which connect to external hubs. The mapping logic will not operate on trunks which are set to external. This prevents incorrect mapping which can occur when a module in one hub detects the mapping signal from another hub. This attribute only applies to copper ring-in trunks.
INT ol5208MTPTrunkSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.14.3.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.
ol5208MTPTrunkTable	1.3.6.1.4.1.49.2.3.1.4.4.14.3		not-accessible	A list of trunk-specific information about each trunk for this module type.
ol52nnBTT	1.3.6.1.4.1.49.2.3.1.4.4.30
INT ol52nnBTTModBridgeType	1.3.6.1.4.1.49.2.3.1.4.4.30.1.1.2	INTEGER	read-only	Whether the bridge is a source-routing bridge or a source-routing-transparent bridge.
ol52nnBTTModEntry	1.3.6.1.4.1.49.2.3.1.4.4.30.1.1		not-accessible	A list of module-specific information about a specific 52nnB-TT module in the concentrator.
INT ol52nnBTTModNetworkStatus	1.3.6.1.4.1.49.2.3.1.4.4.30.1.1.5	INTEGER	read-only	The status of the ring containing this module.
INT ol52nnBTTModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.30.1.1.1	INTEGER	read-only	The slot number of this module.
STR ol52nnBTTModSoftwareVersion	1.3.6.1.4.1.49.2.3.1.4.4.30.1.1.3	DisplayString	read-only	The version number of the software loaded into the module's flash chips.
INT ol52nnBTTModSRBridgeNo	1.3.6.1.4.1.49.2.3.1.4.4.30.1.1.4	INTEGER	read-only	The module's source routing bridge number.
ol52nnBTTModTable	1.3.6.1.4.1.49.2.3.1.4.4.30.1		not-accessible	A table of module-specific information for each 52nnB-TT module in the concentrator.
INT ol52nnBTTPortConnector	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.3	INTEGER	read-write	The port connector. Notice that setting port connector available only for the front pannel port.
ol52nnBTTPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1		not-accessible	A list of port-specific information about a specific 52nnB-TT port in the concentrator.
GAU ol52nnBTTPortForwarding	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.8	Gauge	read-only	Port forwarding rate measured in frames per second.
INT ol52nnBTTPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.2	INTEGER	read-only	The port number for this port within this slot.
IP ol52nnBTTPortIpAddress	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.5	IpAddress	read-only	The IP address associated with this port.
OCT ol52nnBTTPortMACAddress	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.6	OCTET STRING	read-only	A 6 octet address that uniquely identifies this port.
INT ol52nnBTTPortRingSpeed	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.10	INTEGER	read-write	The ring's bandwidth.
INT ol52nnBTTPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.1	INTEGER	read-only	The slot number for this port's module.
INT ol52nnBTTPortSRRingNo	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.9	INTEGER	read-only	The port's source routing ring number.
INT ol52nnBTTPortSTAPState	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.4	INTEGER	read-only	The port connector. Notice that setting port connector available only for the front pannel port.
ol52nnBTTPortTable	1.3.6.1.4.1.49.2.3.1.4.4.30.2		not-accessible	A table of port-specific for each port of each 52nnB-TT module i the concentrator.
GAU ol52nnBTTPortThroughput	1.3.6.1.4.1.49.2.3.1.4.4.30.2.1.7	Gauge	read-only	Port throughput measured in Kbytes per second.
ol52nnBTTTrunkEntry	1.3.6.1.4.1.49.2.3.1.4.4.30.3.1		not-accessible	A list of information about a specific Trunk on a 52nnB-TT module in the concentrator.
INT ol52nnBTTTrunkIndex	1.3.6.1.4.1.49.2.3.1.4.4.30.3.1.2	INTEGER	read-only	The trunk number of this module. Its value ranges between 1 and olModNumTrunks.
INT ol52nnBTTTrunkSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.30.3.1.1	INTEGER	read-only	The slot number of this module. Its value ranges between 1 and olConcNumSlots.
ol52nnBTTTrunkTable	1.3.6.1.4.1.49.2.3.1.4.4.30.3		not-accessible	A table that contains trunk-specific information for each trunk on each 52nnB-TT in the concentrator.
ol52nnMFR	1.3.6.1.4.1.49.2.3.1.4.4.20
INT ol52nnMFRModDipRingSpeed	1.3.6.1.4.1.49.2.3.1.4.4.20.1.1.3	INTEGER	read-only	The dip switch setting for the ring's bandwidth.
ol52nnMFRModEntry	1.3.6.1.4.1.49.2.3.1.4.4.20.1.1		not-accessible	A description of the 52nnMFR module attributes.
INT ol52nnMFRModRingSpeed	1.3.6.1.4.1.49.2.3.1.4.4.20.1.1.2	INTEGER	read-write	The ring's bandwidth.
INT ol52nnMFRModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.20.1.1.1	INTEGER	read-only	The slot number of this module.
ol52nnMFRModTable	1.3.6.1.4.1.49.2.3.1.4.4.20.1		not-accessible	A list of module-specific information about a specific 52nnM-FR module in the concentrator.
INT ol52nnMFRPortCableImp	1.3.6.1.4.1.49.2.3.1.4.4.20.2.1.4	INTEGER	read-only	The setting of this port's impedance matching, with 100 ohm corresponding to unshielded twisted pair cabling and 150 ohm corresponding to shielded twisted pair cabling.
INT ol52nnMFRPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.20.2.1.3	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
ol52nnMFRPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.20.2.1		not-accessible	A description of 52nnMFR port attributes.
INT ol52nnMFRPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.20.2.1.2	INTEGER	read-only	The port number of this port.
INT ol52nnMFRPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.20.2.1.1	INTEGER	read-only	The slot number of this port's module.
INT ol52nnMFRPortStationType	1.3.6.1.4.1.49.2.3.1.4.4.20.2.1.5	INTEGER	read-write	Determines whether the station connected to this port has a MAC address.
ol52nnMFRPortTable	1.3.6.1.4.1.49.2.3.1.4.4.20.2		not-accessible	A table of port-specific information for each port of this module type.
INT ol52nnMFRTrunkCableMon	1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.4	INTEGER	read-write	The cable monitor configuration for this trunk. This does not apply to fiber trunks.
INT ol52nnMFRTrunkCompMode	1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.6	INTEGER	read-write	The compatibility mode for this trunk. This only applies to fiber trunks.
INT ol52nnMFRTrunkDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.3	INTEGER	read-only	The state of this trunk as indicated by the trunk's dip switches.
INT ol52nnMFRTrunkDipCableMon	1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.5	INTEGER	read-only	The cable monitor configuration as indicated by this trunk's dip switches. This does not apply to fiber trunks.
INT ol52nnMFRTrunkDipCompMode	1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.7	INTEGER	read-only	The compatibility mode as indicated by this trunk's dip switches. This only applies to fiber trunks.
ol52nnMFRTrunkEntry	1.3.6.1.4.1.49.2.3.1.4.4.20.3.1		not-accessible	A description of 52nnMFR trunk attributes.
INT ol52nnMFRTrunkExtBcnRecovery	1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.9	INTEGER	read-write	Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for trunks which connect to hubs which perform beacon recovery. This attribute is used to determine the fault domain when resolving a beaconing condition. The beacon recovery process will resolve beaconing on trunks with this attribute set to nonExists(2) before trunks with the attribute set to exists(1) are resolved. For backplane trunks, setting to a value other than notApplicable will return invalidData error. The default value is nonExists(2).
INT ol52nnMFRTrunkIndex	1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.2	INTEGER	read-only	The trunk number of this trunk.
INT ol52nnMFRTrunkNetMapState	1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.8	INTEGER	read-write	The map state of the copper ring-in trunk. This should be set to external for ring-in trunks which connect to external hubs. The mapping logic will not operate on trunks which are set to external. This prevents incorrect mapping which can occur when a module in one hub detects the mapping signal from another hub. This attribute only applies to copper ring-in trunks.
INT ol52nnMFRTrunkSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.20.3.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.
ol52nnMFRTrunkTable	1.3.6.1.4.1.49.2.3.1.4.4.20.3		not-accessible	A list of trunk-specific information about each trunk for this module type.
ol52nnMMGT	1.3.6.1.4.1.49.2.3.1.4.4.32
ol52nnMMGTModEntry	1.3.6.1.4.1.49.2.3.1.4.4.32.1.1		not-accessible	A list of module information for each 52nnM-MGT in the concentrator.
INT ol52nnMMGTModMasterPriority	1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.2	INTEGER	read-write	The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive unless the reset mastership command is used.
INT ol52nnMMGTModMasterStatus	1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.3	INTEGER	read-only	The mastership status of this agent.
INT ol52nnMMGTModNetworkStatus	1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.6	INTEGER	read-only	The status of the ring containing this module.
INT ol52nnMMGTModRingSpeed	1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.5	INTEGER	read-write	The ring's bandwidth.
INT ol52nnMMGTModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.1	INTEGER	read-only	The slot number of this module. Its value ranges between 1 and olConcNumSlots.
OCT ol52nnMMGTModStationAddr	1.3.6.1.4.1.49.2.3.1.4.4.32.1.1.4	OCTET STRING	read-only	A 6 octet address that uniquely identifies this module. The station address is the MAC address of port 1.
ol52nnMMGTModTable	1.3.6.1.4.1.49.2.3.1.4.4.32.1		not-accessible	A table that contains module information about each 52nnM-MGT in the concentrator.
ol52nnMMGTPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.32.2.1		not-accessible	A list of information about a specific port on a 52nnM-MGT module in the concentrator.
INT ol52nnMMGTPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.32.2.1.2	INTEGER	read-only	The port number of this port.
IP ol52nnMMGTPortIpAddress	1.3.6.1.4.1.49.2.3.1.4.4.32.2.1.3	IpAddress	read-write	The IP address associated with this port.
INT ol52nnMMGTPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.32.2.1.1	INTEGER	read-only	The slot number of this port's module.
ol52nnMMGTPortTable	1.3.6.1.4.1.49.2.3.1.4.4.32.2		not-accessible	A table that contains port-specific information for each port on each 52nnM-MGT in the concentrator.
INT ol52nnMMGTTrunkCableMon	1.3.6.1.4.1.49.2.3.1.4.4.32.3.1.3	INTEGER	read-write	The cable monitor configuration for this trunk.
ol52nnMMGTTrunkEntry	1.3.6.1.4.1.49.2.3.1.4.4.32.3.1		not-accessible	A list of information about a specific Trunk on a 52nnM-MGT module in the concentrator.
INT ol52nnMMGTTrunkExtBcnRecovery	1.3.6.1.4.1.49.2.3.1.4.4.32.3.1.5	INTEGER	read-write	Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for trunks which connect to hubs which perform beacon recovery. This attribute is used to determine the fault domain when resolving a beaconing condition. The beacon recovery process will resolve beaconing on trunks with this attribute set to nonExists(2) before trunks with the attribute set to exists(1) are resolved. For backplane trunks, setting to a value other than notApplicable will return invalidData error. The default value is nonExists(2).
INT ol52nnMMGTTrunkIndex	1.3.6.1.4.1.49.2.3.1.4.4.32.3.1.2	INTEGER	read-only	The slot number of this module. Its value ranges between 1 and olModNumTrunks.
INT ol52nnMMGTTrunkNetMapState	1.3.6.1.4.1.49.2.3.1.4.4.32.3.1.4	INTEGER	read-write	The map state of the copper ring-in trunk. This should be set to external for ring-in trunks which connect to external hubs. The mapping logic will not operate on trunks which are set to external. This prevents incorrect mapping which can occur when a module in one hub detects the mapping signal from another hub. This attribute only applies to copper ring-in trunks.
INT ol52nnMMGTTrunkSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.32.3.1.1	INTEGER	read-only	The slot number of this module. Its value ranges between 1 and olConcNumSlots.
ol52nnMMGTTrunkTable	1.3.6.1.4.1.49.2.3.1.4.4.32.3		not-accessible	A table that contains trunk-specific information for each trunk on each 52nnM-MGT in the concentrator.
ol52nnMTP	1.3.6.1.4.1.49.2.3.1.4.4.19
INT ol52nnMTPModCableImp	1.3.6.1.4.1.49.2.3.1.4.4.19.1.1.4	INTEGER	read-write	The setting of this module's port impedance matching, with 100 ohm corresponding to unshielded twisted pair cabling and 150 ohm corresponding to shielded twisted pair cabling. This setting is valid for all ports on this module.
INT ol52nnMTPModDipCableImp	1.3.6.1.4.1.49.2.3.1.4.4.19.1.1.5	INTEGER	read-only	The dip switch setting for the module's port impedance matching.
INT ol52nnMTPModDipRingSpeed	1.3.6.1.4.1.49.2.3.1.4.4.19.1.1.3	INTEGER	read-only	The dip switch setting for the ring's bandwidth.
ol52nnMTPModEntry	1.3.6.1.4.1.49.2.3.1.4.4.19.1.1		not-accessible	A description of the 52nnM-TP module attributes.
INT ol52nnMTPModRingSpeed	1.3.6.1.4.1.49.2.3.1.4.4.19.1.1.2	INTEGER	read-write	The ring's bandwidth.
INT ol52nnMTPModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.19.1.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.
ol52nnMTPModTable	1.3.6.1.4.1.49.2.3.1.4.4.19.1		not-accessible	A list of module-specific information about a specific 52nnM-TP module in the concentrator.
INT ol52nnMTPPortDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.19.2.1.3	INTEGER	read-only	The state of this port as indicated by the port's dip switches.
ol52nnMTPPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.19.2.1		not-accessible	A description of 52nnM-TP port attributes.
INT ol52nnMTPPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.19.2.1.2	INTEGER	read-only	The port number of this port.
INT ol52nnMTPPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.19.2.1.1	INTEGER	read-only	The slot number of this port's module.
INT ol52nnMTPPortStationType	1.3.6.1.4.1.49.2.3.1.4.4.19.2.1.4	INTEGER	read-write	Determines whether the station connected to this port has a MAC address.
ol52nnMTPPortTable	1.3.6.1.4.1.49.2.3.1.4.4.19.2		not-accessible	A table of port-specific information for each port of this module type.
INT ol52nnMTPTrunkDipAdminState	1.3.6.1.4.1.49.2.3.1.4.4.19.3.1.3	INTEGER	read-only	The state of this trunk as indicated by the trunk's dip switches.
ol52nnMTPTrunkEntry	1.3.6.1.4.1.49.2.3.1.4.4.19.3.1		not-accessible	A description of 52nnM-TP trunk attributes.
INT ol52nnMTPTrunkIndex	1.3.6.1.4.1.49.2.3.1.4.4.19.3.1.2	INTEGER	read-only	The trunk number for this trunk.
INT ol52nnMTPTrunkSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.19.3.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.
ol52nnMTPTrunkTable	1.3.6.1.4.1.49.2.3.1.4.4.19.3		not-accessible	A list of trunk-specific information about each trunk for this module type.
ol53nnMFBMIC	1.3.6.1.4.1.49.2.3.1.4.4.26
INT ol53nnMFBMICModDownStreamModule	1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.2	INTEGER	read-only	Down stream slot (transmit to)
INT ol53nnMFBMICModDownStreamOperPath	1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.4	INTEGER	read-only	Transmit DBA (debug only)
ol53nnMFBMICModEntry	1.3.6.1.4.1.49.2.3.1.4.4.26.1.1		not-accessible	A list of module-specific information about a specific 53nnM-FBMIC module in the concentrator.
OCT ol53nnMFBMICModRingInfo	1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.6	OCTET STRING	read-only	An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only)
INT ol53nnMFBMICModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.
ol53nnMFBMICModTable	1.3.6.1.4.1.49.2.3.1.4.4.26.1		not-accessible	A list of module attributes that apply to this model. To access an ol53nnMFBMICModTable entry, the ol53nnMFBMICModSlotIndex attribute is used.
INT ol53nnMFBMICModUpStreamModule	1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.3	INTEGER	read-only	Up stream slot (receve from)
INT ol53nnMFBMICModUpStreamOperPath	1.3.6.1.4.1.49.2.3.1.4.4.26.1.1.5	INTEGER	read-only	Receive DBA (debug only)
INT ol53nnMFBMICPortBSFlag	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.8	INTEGER	read-only	The Break State, BS_Flag (refer to ANSI SMT 9.4.3.4).
INT ol53nnMFBMICPortConfig	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.3	INTEGER	read-write	Specifies the FDDI port type. If the port is on an FPM, the only allowed values are slave(3), and master(4). In addition, there can only be one active slave port on any concentrator FDDI network.
INT ol53nnMFBMICPortConnectState	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.5	INTEGER	read-only	An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Withhold flag state. The supported values and their corresponding PCM states and PC-Withhold condition, when relevant, are: disabled: (PC0:Off, PC9:Maint) connecting: (PC1(Break) \|\| PC3 (Connect) \|\| PC4(next) \|\| PC5 (Signal) \|\| PC6(Join) \|\| PC7 (Verify)) && (PC_Withhold = None) standby: (PC_Withhold != None) active: (PC2:Trace \|\| PC8:Active)
ol53nnMFBMICPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1		not-accessible	A list of module-specific information about a specific 53nnM-FBMIC port in the concentrator.
INT ol53nnMFBMICPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.2	INTEGER	read-only	A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortIndex.
INT ol53nnMFBMICPortLerCondition	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.10	INTEGER	read-only	This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value).
INT ol53nnMFBMICPortNeighbor	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.6	INTEGER	read-only	The type (PC_Neighbor) of the remote PORT that is determined in PC_Signaling in R_Val (1,2) (refer to ANSI SMT 9.6.3.2).
INT ol53nnMFBMICPortPcmState	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.4	INTEGER	read-only	(refer to ANSI SMT 9.6.2).
INT ol53nnMFBMICPortPCWithhold	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.9	INTEGER	read-only	PC_Withhold, (refer to ANSI SMT 9.4.1).
INT ol53nnMFBMICPortRemoteMACIndicated	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.7	INTEGER	read-only	The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R_Val (9) (refer to ANSI SMT 9.6.3.2).
INT ol53nnMFBMICPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.26.2.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.
ol53nnMFBMICPortTable	1.3.6.1.4.1.49.2.3.1.4.4.26.2		not-accessible	A table of port-specific information for each port of this module type.
ol53nnMFBMICTrunkEntry	1.3.6.1.4.1.49.2.3.1.4.4.26.3.1		not-accessible	A description of 53nnM-FBMIC trunk attributes.
INT ol53nnMFBMICTrunkIndex	1.3.6.1.4.1.49.2.3.1.4.4.26.3.1.2	INTEGER	read-only	A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkIndex.
INT ol53nnMFBMICTrunkSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.26.3.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.
ol53nnMFBMICTrunkTable	1.3.6.1.4.1.49.2.3.1.4.4.26.3		not-accessible	FDDI module specific trunk table variables. At present there are none.
ol53nnMFIBST	1.3.6.1.4.1.49.2.3.1.4.4.27
INT ol53nnMFIBSTModDownStreamModule	1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.2	INTEGER	read-only	Down stream slot (transmit to)
INT ol53nnMFIBSTModDownStreamOperPath	1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.4	INTEGER	read-only	Transmit DBA (debug only)
ol53nnMFIBSTModEntry	1.3.6.1.4.1.49.2.3.1.4.4.27.1.1		not-accessible	A list of module-specific information about a specific 53nnM-FIBST module in the concentrator.
OCT ol53nnMFIBSTModRingInfo	1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.6	OCTET STRING	read-only	An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only)
INT ol53nnMFIBSTModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.
ol53nnMFIBSTModTable	1.3.6.1.4.1.49.2.3.1.4.4.27.1		not-accessible	A list of module attributes that apply to this model. To access an ol53nnMFIBSTModTable entry, the ol53nnMFIBSTModSlotIndex attribute is used.
INT ol53nnMFIBSTModUpStreamModule	1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.3	INTEGER	read-only	Up stream slot (receve from)
INT ol53nnMFIBSTModUpStreamOperPath	1.3.6.1.4.1.49.2.3.1.4.4.27.1.1.5	INTEGER	read-only	Receive DBA (debug only)
INT ol53nnMFIBSTPortBSFlag	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.8	INTEGER	read-only	The Break State, BS_Flag (refer to ANSI SMT 9.4.3.4).
INT ol53nnMFIBSTPortConfig	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.3	INTEGER	read-write	Specifies the FDDI port type. If the port is on an FPM, the only allowed values are slave(3) and master(4). In addition, there can only be one active slave port on any concentrator FDDI network.
INT ol53nnMFIBSTPortConnectState	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.5	INTEGER	read-only	An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Withhold flag state. The supported values and their corresponding PCM states and PC-Withhold condition, when relevant, are: disabled: (PC0:Off, PC9:Maint) connecting: (PC1(Break) \|\| PC3 (Connect) \|\| PC4(next) \|\| PC5 (Signal) \|\| PC6(Join) \|\| PC7 (Verify)) && (PC_Withhold = None) standby: (PC_Withhold != None) active: (PC2:Trace \|\| PC8:Active)
ol53nnMFIBSTPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1		not-accessible	A list of module-specific information about a specific 53nnM-FIBST port in the concentrator.
INT ol53nnMFIBSTPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.2	INTEGER	read-only	A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortIndex.
INT ol53nnMFIBSTPortLerCondition	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.10	INTEGER	read-only	This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value).
INT ol53nnMFIBSTPortNeighbor	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.6	INTEGER	read-only	The type (PC_Neighbor) of the remote PORT that is determined in PC_Signaling in R_Val (1,2) (refer to ANSI SMT 9.6.3.2).
INT ol53nnMFIBSTPortPcmState	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.4	INTEGER	read-only	(refer to ANSI SMT 9.6.2).
INT ol53nnMFIBSTPortPCWithhold	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.9	INTEGER	read-only	PC_Withhold, (refer to ANSI SMT 9.4.1).
INT ol53nnMFIBSTPortRemoteMACIndicated	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.7	INTEGER	read-only	The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R_Val (9) (refer to ANSI SMT 9.6.3.2).
INT ol53nnMFIBSTPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.27.2.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.
ol53nnMFIBSTPortTable	1.3.6.1.4.1.49.2.3.1.4.4.27.2		not-accessible	A table of port-specific information for each port of this module type.
ol53nnMFIBSTTrunkEntry	1.3.6.1.4.1.49.2.3.1.4.4.27.3.1		not-accessible	A description of 53nnM-FIBST trunk attributes.
INT ol53nnMFIBSTTrunkIndex	1.3.6.1.4.1.49.2.3.1.4.4.27.3.1.2	INTEGER	read-only	A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkIndex.
INT ol53nnMFIBSTTrunkSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.27.3.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.
ol53nnMFIBSTTrunkTable	1.3.6.1.4.1.49.2.3.1.4.4.27.3		not-accessible	FDDI module specific trunk table variables. At present there are none.
ol53nnMMGT	1.3.6.1.4.1.49.2.3.1.4.4.25
OCT ol53nnMMGTModDownStreamMAC	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.6	OCTET STRING	read-only	Down stream MAC
INT ol53nnMMGTModDownStreamModule	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.9	INTEGER	read-only	Down stream slot (transmit to)
INT ol53nnMMGTModDownStreamOperPath	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.11	INTEGER	read-only	Transmit DBA (debug only)
ol53nnMMGTModEntry	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1		not-accessible	A list of module-specific information about a specific 53nnM-MGT module in the concentrator.
INT ol53nnMMGTModfddiMACPath	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.8	INTEGER	read-write	The FDDI path which should be inserted into the MAC
IP ol53nnMMGTModIpAddress	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.5	IpAddress	read-write	The IP address associated with this module.
INT ol53nnMMGTModMasterPriority	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.2	INTEGER	read-write	The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive unless the reset mastership command is used.
INT ol53nnMMGTModMasterStatus	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.3	INTEGER	read-only	The mastership status of this agent.
OCT ol53nnMMGTModRingInfo	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.13	OCTET STRING	read-only	An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only)
INT ol53nnMMGTModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.
OCT ol53nnMMGTModStationAddr	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.4	OCTET STRING	read-only	A 6 octet address that uniquely identifies this module. The station address is the MAC address of port 1.
ol53nnMMGTModTable	1.3.6.1.4.1.49.2.3.1.4.4.25.1		not-accessible	A list of module attributes that apply to this model. To access an ol53nnMMGTModTable entry, the ol53nnMMGTModSlotIndex attribute is used.
OCT ol53nnMMGTModUpStreamMAC	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.7	OCTET STRING	read-only	Up stream MAC
INT ol53nnMMGTModUpStreamModule	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.10	INTEGER	read-only	Up stream slot (receve from)
INT ol53nnMMGTModUpStreamOperPath	1.3.6.1.4.1.49.2.3.1.4.4.25.1.1.12	INTEGER	read-only	Receive DBA (debug only)
INT ol53nnMMGTPortBSFlag	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.8	INTEGER	read-only	The Break State, BS_Flag (refer to ANSI SMT 9.4.3.4).
INT ol53nnMMGTPortConfig	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.3	INTEGER	read-only	Specifies the FDDI port type (a or b).
INT ol53nnMMGTPortConnectState	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.5	INTEGER	read-only	An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Withhold flag state. The supported values and their corresponding PCM states and PC-Withhold condition, when relevant, are: disabled: (PC0:Off, PC9:Maint) connecting: (PC1(Break) \|\| PC3 (Connect) \|\| PC4(next) \|\| PC5 (Signal) \|\| PC6(Join) \|\| PC7 (Verify)) && (PC_Withhold = None) standby: (PC_Withhold != None) active: (PC2:Trace \|\| PC8:Active)
ol53nnMMGTPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1		not-accessible	A list of module-specific information about a specific 53nnM-MGT port in the concentrator.
INT ol53nnMMGTPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.2	INTEGER	read-only	A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortIndex.
INT ol53nnMMGTPortLerCondition	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.10	INTEGER	read-only	This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value).
INT ol53nnMMGTPortNeighbor	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.6	INTEGER	read-only	The type (PC_Neighbor) of the remote PORT that is determined in PC_Signaling in R_Val (1,2) (refer to ANSI SMT 9.6.3.2).
INT ol53nnMMGTPortPcmState	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.4	INTEGER	read-only	(refer to ANSI SMT 9.6.2).
INT ol53nnMMGTPortPCWithhold	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.9	INTEGER	read-only	PC_Withhold, (refer to ANSI SMT 9.4.1).
INT ol53nnMMGTPortRemoteMACIndicated	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.7	INTEGER	read-only	The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R_Val (9) (refer to ANSI SMT 9.6.3.2).
INT ol53nnMMGTPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.25.2.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.
ol53nnMMGTPortTable	1.3.6.1.4.1.49.2.3.1.4.4.25.2		not-accessible	A table of port-specific information for each port of this module type.
ol53nnMMGTTrunkEntry	1.3.6.1.4.1.49.2.3.1.4.4.25.3.1		not-accessible	A description of 53nnM-MGT trunk attributes.
INT ol53nnMMGTTrunkIndex	1.3.6.1.4.1.49.2.3.1.4.4.25.3.1.2	INTEGER	read-only	A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkIndex.
INT ol53nnMMGTTrunkSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.25.3.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.
ol53nnMMGTTrunkTable	1.3.6.1.4.1.49.2.3.1.4.4.25.3		not-accessible	FDDI module specific trunk table variables. At present there are none.
ol53nnMSTP	1.3.6.1.4.1.49.2.3.1.4.4.28
INT ol53nnMSTPModDownStreamModule	1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.2	INTEGER	read-only	Down stream slot (transmit to)
INT ol53nnMSTPModDownStreamOperPath	1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.4	INTEGER	read-only	transmit DBA (debug only)
ol53nnMSTPModEntry	1.3.6.1.4.1.49.2.3.1.4.4.28.1.1		not-accessible	A list of module-specific information about a specific 53nnM-FIBSTP module in the concentrator.
OCT ol53nnMSTPModRingInfo	1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.6	OCTET STRING	read-only	An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only)
INT ol53nnMSTPModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.
ol53nnMSTPModTable	1.3.6.1.4.1.49.2.3.1.4.4.28.1		not-accessible	A list of module attributes that apply to this model. To access an ol53nnMSTPModTable entry, the ol53nnMSTPModSlotIndex attribute is used.
INT ol53nnMSTPModUpStreamModule	1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.3	INTEGER	read-only	Down stream slot (receve from)
INT ol53nnMSTPModUpStreamOperPath	1.3.6.1.4.1.49.2.3.1.4.4.28.1.1.5	INTEGER	read-only	receive DBA (debug only)
INT ol53nnMSTPPortBSFlag	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.8	INTEGER	read-only	The Break State, BS_Flag (refer to ANSI SMT 9.4.3.4).
INT ol53nnMSTPPortConfig	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.3	INTEGER	read-write	Specifies the FDDI port type. If the port is on an FPM, the only allowed values are slave(3) and master(4). In addition, there can only be one active slave port on any concentrator FDDI network.
INT ol53nnMSTPPortConnectState	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.5	INTEGER	read-only	An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Withhold flag state. The supported values and their corresponding PCM states and PC-Withhold condition, when relevant, are: disabled: (PC0:Off, PC9:Maint) connecting: (PC1(Break) \|\| PC3 (Connect) \|\| PC4(next) \|\| PC5 (Signal) \|\| PC6(Join) \|\| PC7 (Verify)) && (PC_Withhold = None) standby: (PC_Withhold != None) active: (PC2:Trace \|\| PC8:Active)
ol53nnMSTPPortEntry	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1		not-accessible	A list of module-specific information about a specific 53nnM-STP port in the concentrator.
INT ol53nnMSTPPortIndex	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.2	INTEGER	read-only	A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortIndex.
INT ol53nnMSTPPortLerCondition	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.10	INTEGER	read-only	This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value).
INT ol53nnMSTPPortNeighbor	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.6	INTEGER	read-only	The type (PC_Neighbor) of the remote PORT that is determined in PC_Signaling in R_Val (1,2) (refer to ANSI SMT 9.6.3.2).
INT ol53nnMSTPPortPcmState	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.4	INTEGER	read-only	(refer to ANSI SMT 9.6.2).
INT ol53nnMSTPPortPCWithhold	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.9	INTEGER	read-only	PC_Withhold, (refer to ANSI SMT 9.4.1).
INT ol53nnMSTPPortPersonality	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.11	INTEGER	read-write	Specifies the physical signaling used by the port, the only valid values are sddi(3) and tpddi(4).
INT ol53nnMSTPPortRemoteMACIndicated	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.7	INTEGER	read-only	The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R_Val (9) (refer to ANSI SMT 9.6.3.2).
INT ol53nnMSTPPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.28.2.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.
ol53nnMSTPPortTable	1.3.6.1.4.1.49.2.3.1.4.4.28.2		not-accessible	A table of port-specific information for each port of this module type.
ol53nnMSTPTrunkEntry	1.3.6.1.4.1.49.2.3.1.4.4.28.3.1		not-accessible	A description of 53nnM-STP trunk attributes.
INT ol53nnMSTPTrunkIndex	1.3.6.1.4.1.49.2.3.1.4.4.28.3.1.2	INTEGER	read-only	A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkIndex.
INT ol53nnMSTPTrunkSlotIndex	1.3.6.1.4.1.49.2.3.1.4.4.28.3.1.1	INTEGER	read-only	A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.
ol53nnMSTPTrunkTable	1.3.6.1.4.1.49.2.3.1.4.4.28.3		not-accessible	FDDI module specific trunk table variables. At present there are none.
olAgents	1.3.6.1.4.1.49.2.3.1.1
olAgentsEntry	1.3.6.1.4.1.49.2.3.1.1.3.1		not-accessible	A profile of an agent within the concentrator.
IP olAgentsIpAddress	1.3.6.1.4.1.49.2.3.1.1.3.1.3	IpAddress	read-only	An IP Address that can be used to communicate to this agent. Note, this object's value may change as the agent switches to different sub-networks.
INT olAgentsMasterPriority	1.3.6.1.4.1.49.2.3.1.1.3.1.5	INTEGER	read-write	The mastership priority of this agent. Ten is the highest and one is the lowest. Never means will not be able become master. Some agents do not have the capability to become master (the etherent to ethernet bridge, e.g.) and setting those agents to a value other than never(11) will generate an invalid value error. Priority is only used when an election occurs. Mastership is not pre-emptive; use the reset mastership command (olAgentsMasterReset).
INT olAgentsMasterReset	1.3.6.1.4.1.49.2.3.1.1.2	INTEGER	read-write	Resetting mastership causes a new mastership election to occur. The agent with the highest mastership priority will become the new master. If there is more than one agent with the highest priority, the selection between those agents will be arbritrary.
INT olAgentsMasterStatus	1.3.6.1.4.1.49.2.3.1.1.3.1.4	INTEGER	read-only	The mastership status of this agent.
INT olAgentsMySlot	1.3.6.1.4.1.49.2.3.1.1.1	INTEGER	read-only	The slot id of this agent.
INT olAgentsSlotIndex	1.3.6.1.4.1.49.2.3.1.1.3.1.1	INTEGER	read-only	The slot number that identifies the referenced agent.
OCT olAgentsStationAddr	1.3.6.1.4.1.49.2.3.1.1.3.1.2	OCTET STRING	read-only	The unique identifier for this agent. Often this is the value of ifPhysAddress for the first interface.
olAgentsTable	1.3.6.1.4.1.49.2.3.1.1.3		not-accessible	A table of agents in the concentrator as seen by this agent. A master will see all the agents; a slave will only see itself.
olAlarm	1.3.6.1.4.1.49.2.3.1.7
olConc	1.3.6.1.4.1.49.2.3.1.2
INT olConcNumSlots	1.3.6.1.4.1.49.2.3.1.2.3	INTEGER	read-only	The number of slots in this concentrator. Note, that if a hidden controller is present, the number of slots is one more than the number of payload slots (six-slot-hc will report 7 slots, for example). The hidden controller does not actually occupy a main slot in the 6-slot concentrator, but it will report itself as slot 7.
OCT olConcProfile	1.3.6.1.4.1.49.2.3.1.2.4	OCTET STRING	read-only	A bit string where the least significant bit corresponds to slot 1. A '1' in the bit indicates that a module is present in that slot. The number of octets provided is based on the olConcNumSlots value divided by 8. Any extra bits (for example, bits 18-24 for 17 slots) are meaningless. For example, the string 0x01 0xFF 0xFF would represent a full 17 slot concentrator.
INT olConcReset	1.3.6.1.4.1.49.2.3.1.2.2	INTEGER	read-write	Setting this value to reset(2) causes this concentrator to reset.
INT olConcType	1.3.6.1.4.1.49.2.3.1.2.1	INTEGER	read-only	This object identifies the type of concentrator represented by this agent.
olEnet	1.3.6.1.4.1.49.2.3.1.5.2
OCT olEnetMapAddress	1.3.6.1.4.1.49.2.3.1.5.2.4.1.2	OCTET STRING	read-only	An Ethernet source address received by this port on this network.
olEnetMapEntry	1.3.6.1.4.1.49.2.3.1.5.2.4.1		not-accessible	A list of information that tracks a source address to a specific port for each network.
CTR olEnetMapFrames	1.3.6.1.4.1.49.2.3.1.5.2.4.1.5	Counter	read-only	An estimated count of the number of frames generated by this address. This count should be interpreted as an indicator, not a true frame count.
INT olEnetMapNetID	1.3.6.1.4.1.49.2.3.1.5.2.4.1.1	INTEGER	read-only	The network index that uniquely identifies this network. One of ethernet-1, ethernet-2, ethernet-3.
CTR olEnetMapOctets	1.3.6.1.4.1.49.2.3.1.5.2.4.1.6	Counter	read-only	An estimated count of the number of octets generated by this address. This count should be interpreted as an indicator, not a true octet count.
INT olEnetMapPortIndex	1.3.6.1.4.1.49.2.3.1.5.2.4.1.4	INTEGER	read-only	The port number within olEnetMapSlotIndex's slot that received this address.
INT olEnetMapSlotIndex	1.3.6.1.4.1.49.2.3.1.5.2.4.1.3	INTEGER	read-only	The slot number of the port that received this address.
olEnetMapTable	1.3.6.1.4.1.49.2.3.1.5.2.4		not-accessible	A table that contains a cache of information relating an Ethernet source address with a specific port for a given network. An indication of this source's utilization of the network is also provided.
TIK olEnetMapTime	1.3.6.1.4.1.49.2.3.1.5.2.4.1.7	TimeTicks	read-only	The time in in hundredths of a second since this address was last seen. For example, if olEnetMapTime is 500 ticks, then this adddress was seen 5 seconds ago.
CTR olEnetStatsAlignmentErrors	1.3.6.1.4.1.49.2.3.1.5.2.1.1.7	Counter	read-only	The count of the number of frames received by this network that did not pass the frame check sequence (FCS) check and that are not an integral number of octets. These frames are not counted in olEnetStatsFCSErrors.
CTR olEnetStatsBcastRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.1.1.5	Counter	read-only	The count of the number of broadcast frames successfully received by this network.
olEnetStatsEntry	1.3.6.1.4.1.49.2.3.1.5.2.1.1		not-accessible	A list of statistical information about each Ethernet (IEEE 802.3) network in the concentrator.
CTR olEnetStatsFCSErrors	1.3.6.1.4.1.49.2.3.1.5.2.1.1.8	Counter	read-only	The count of the number of frames received by this network that did not pass the frame check sequence (FCS) check and are an integral number of octets.
CTR olEnetStatsFramesRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.1.1.2	Counter	read-only	The count of frames that were successfully received by this network. This counter does not include frames received in error.
CTR olEnetStatsFrameTooLongs	1.3.6.1.4.1.49.2.3.1.5.2.1.1.6	Counter	read-only	The count of the number of frames received by this network that exceeds the maximum permitted Ethernet (802.3) frame size.
CTR olEnetStatsLocalColls	1.3.6.1.4.1.49.2.3.1.5.2.1.1.10	Counter	read-only	The count of the number of times that two or more ports within this concentrator have received traffic simultaneously.
CTR olEnetStatsMcastRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.1.1.4	Counter	read-only	The count of the number of multicast frames successfully received by this network.
CTR olEnetStatsModAlignmentErrors	1.3.6.1.4.1.49.2.3.1.5.2.2.1.8	Counter	read-only	The count of the number of frames received by this module that did not pass the frame check sequence (FCS) check and that are not an integral number of octets. These frames are not counted in olEnetStatsModFCSErrors.
CTR olEnetStatsModBcastRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.2.1.6	Counter	read-only	The count of the number of broadcast frames successfully received by this module.
olEnetStatsModEntry	1.3.6.1.4.1.49.2.3.1.5.2.2.1		not-accessible	A list of statistical information for each port on each Ethernet (IEEE 802.3) network in the concentrator.
CTR olEnetStatsModFCSErrors	1.3.6.1.4.1.49.2.3.1.5.2.2.1.9	Counter	read-only	The count of the number of frames received by this module that did not pass the frame check sequence (FCS) check and are an integral number of octets.
CTR olEnetStatsModFramesRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.2.1.3	Counter	read-only	The count of frames that were successfully received by this module. This counter does not include frames received in error.
CTR olEnetStatsModFrameTooLongs	1.3.6.1.4.1.49.2.3.1.5.2.2.1.7	Counter	read-only	The count of the number of frames received by this module that exceeds the maximum permitted Ethernet (802.3) frame size.
CTR olEnetStatsModMcastRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.2.1.5	Counter	read-only	The count of the number of multicast frames successfully received by this module.
INT olEnetStatsModNetID	1.3.6.1.4.1.49.2.3.1.5.2.2.1.1	INTEGER	read-only	The unique identifier for this network. One of ethernet-1, ethernet-2, or ethernet-3.
CTR olEnetStatsModOctetsRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.2.1.4	Counter	read-only	The count of the number of octets that were successfully received by this module. This counter does not include octets that were part of frames that were received in error.
CTR olEnetStatsModRunts	1.3.6.1.4.1.49.2.3.1.5.2.2.1.10	Counter	read-only	The count of the number of frames received by this module that are less than 512 bits long.
INT olEnetStatsModSlotIndex	1.3.6.1.4.1.49.2.3.1.5.2.2.1.2	INTEGER	read-only	The slot number that contains this module.
olEnetStatsModTable	1.3.6.1.4.1.49.2.3.1.5.2.2		not-accessible	A table of statistical information counted for each module in each Ethernet (IEEE 802.3) network.
INT olEnetStatsNetID	1.3.6.1.4.1.49.2.3.1.5.2.1.1.1	INTEGER	read-only	The network index that uniquely identifies this network. One of ethernet-1, ethernet-2, or ethernet-3.
CTR olEnetStatsOctetsRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.1.1.3	Counter	read-only	The count of the number of octets that were successfully received by this network. This counter does not include octets that were part of frames that were received in error.
CTR olEnetStatsPortAlignmentErrors	1.3.6.1.4.1.49.2.3.1.5.2.3.1.9	Counter	read-only	The count of the number of frames received by this port that did not pass the frame check sequence (FCS) check and that are not an integral number of octets. These frames are not counted in olEnetStatsPortFCSErrors.
CTR olEnetStatsPortBcastRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.3.1.7	Counter	read-only	The count of the number of broadcast frames successfully received by this port.
olEnetStatsPortEntry	1.3.6.1.4.1.49.2.3.1.5.2.3.1		not-accessible	A list of statistical information for each port on each Ethernet (IEEE 802.3) network in the concentrator.
CTR olEnetStatsPortFCSErrors	1.3.6.1.4.1.49.2.3.1.5.2.3.1.10	Counter	read-only	The count of the number of frames received by this port that did not pass the frame check sequence (FCS) check and are an integral number of octets.
CTR olEnetStatsPortFramesRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.3.1.4	Counter	read-only	The count of frames that were successfully received by this port. This counter does not include frames received in error.
CTR olEnetStatsPortFrameTooLongs	1.3.6.1.4.1.49.2.3.1.5.2.3.1.8	Counter	read-only	The count of the number of frames received by this port that exceeds the maximum permitted Ethernet (802.3) frame size.
INT olEnetStatsPortIndex	1.3.6.1.4.1.49.2.3.1.5.2.3.1.3	INTEGER	read-only	The port number within this slot.
OCT olEnetStatsPortLastErrAddr	1.3.6.1.4.1.49.2.3.1.5.2.3.1.14	OCTET STRING	read-only	The value stored in the source address portion of a frame received in error (alignment, FCS, or too long). Since the frame was received in error, there is no guarantee that this is an actual valid address.
OCT olEnetStatsPortLastSrcAddr	1.3.6.1.4.1.49.2.3.1.5.2.3.1.13	OCTET STRING	read-only	The last source address seen on this port for this network for the last successfully received frame.
CTR olEnetStatsPortMcastRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.3.1.6	Counter	read-only	The count of the number of multicast frames successfully received by this port.
INT olEnetStatsPortNetID	1.3.6.1.4.1.49.2.3.1.5.2.3.1.1	INTEGER	read-only	The unique identifier for this network. One of ethernet-1, ethernet-2, or ethernet-3.
CTR olEnetStatsPortOctetsRcvdOks	1.3.6.1.4.1.49.2.3.1.5.2.3.1.5	Counter	read-only	The count of the number of octets that were successfully received by this port. This counter does not include octets that were part of frames that were received in error.
CTR olEnetStatsPortRunts	1.3.6.1.4.1.49.2.3.1.5.2.3.1.11	Counter	read-only	The count of the number of frames received by this port that are less than 512 bits long.
INT olEnetStatsPortSlotIndex	1.3.6.1.4.1.49.2.3.1.5.2.3.1.2	INTEGER	read-only	The slot number that contains this port.
CTR olEnetStatsPortSrcAddrChanges	1.3.6.1.4.1.49.2.3.1.5.2.3.1.12	Counter	read-only	The count of the number of times that olEnetStatsPortLastSourceAddr { olEnetStatsPortEntry 11 } has changed.
olEnetStatsPortTable	1.3.6.1.4.1.49.2.3.1.5.2.3		not-accessible	A table of statistical information counted for each port in each Ethernet (IEEE 802.3) network.
CTR olEnetStatsRunts	1.3.6.1.4.1.49.2.3.1.5.2.1.1.9	Counter	read-only	The count of the number of frames received by this network that are less than 512 bits long.
olEnetStatsTable	1.3.6.1.4.1.49.2.3.1.5.2.1		not-accessible	A table that contains statistical information about Ethernet (IEEE 802.3) networks.
olEnv	1.3.6.1.4.1.49.2.3.1.3
INT olEnvFanStatus	1.3.6.1.4.1.49.2.3.1.3.4	INTEGER	read-only	The overall status of the fan(s).
INT olEnvPSAdminState	1.3.6.1.4.1.49.2.3.1.3.3.1.2	INTEGER	read-write	The current desired state of the power supply. A power supply in standby does not provide power to the concentrator.
INT olEnvPSCapacity	1.3.6.1.4.1.49.2.3.1.3.2	INTEGER	read-only	The total capacity of power supplies for this concentrator.
olEnvPSEntry	1.3.6.1.4.1.49.2.3.1.3.3.1		not-accessible	A list of of information for each power supply in the concentrator.
INT olEnvPSIndex	1.3.6.1.4.1.49.2.3.1.3.3.1.1	INTEGER	read-only	Identifies the power supply for which this entry contains power supply information. For systems with the primary and backup power supply (as opposed to the N+1 design), index 1 refers to the primary, and index 2 refers to the backup.
INT olEnvPSOperStatus	1.3.6.1.4.1.49.2.3.1.3.3.1.3	INTEGER	read-only	The current operational state of the power supply. A power supply in standby does not provide power to the concentrator.
olEnvPSTable	1.3.6.1.4.1.49.2.3.1.3.3		not-accessible	A table that contains information about each potential power supply in the concentrator.
INT olEnvTempStatus	1.3.6.1.4.1.49.2.3.1.3.1	INTEGER	read-only	The overall temperature status for this concentrator. This object's value is an aggregate of all the temperature probes in the concentrator, such that, when at least one probe reports extreme temperature, this object will have the value extremeTemp(2).
olFDDInet	1.3.6.1.4.1.49.2.3.1.5.4
olFDDInetStatsEntry	1.3.6.1.4.1.49.2.3.1.5.4.4.1		not-accessible	A list of statistical information for each FDDI network in the concentrator.
CTR olFDDInetStatsErrorCounts	1.3.6.1.4.1.49.2.3.1.5.4.4.1.4	Counter	read-only	Error_Ct (refer to ANSI MAC 2.2.1).
CTR olFDDInetStatsFrameCounts	1.3.6.1.4.1.49.2.3.1.5.4.4.1.3	Counter	read-only	Frame_Ct (refer to ANSI MAC 2.2.1).
INT olFDDInetStatsFrameErrorRatio	1.3.6.1.4.1.49.2.3.1.5.4.4.1.6	INTEGER	read-only	This attribute is the actual ratio, ((delta snmpFddiMACLostCt + delta snmpFddiMACErrorCt) / (delta snmpFddiMACFrameCt + delta snmpFddiMACLostCt)) x 2**16.
CTR olFDDInetStatsLostCounts	1.3.6.1.4.1.49.2.3.1.5.4.4.1.5	Counter	read-only	Lost_Ct (refer to ANSI MAC 2.2.1).
INT olFDDInetStatsNetID	1.3.6.1.4.1.49.2.3.1.5.4.4.1.1	INTEGER	read-only	The network index that uniquely identifies this network. One of isolated, fddi-1, fddi-2, fddi-3, or fddi-4.
CTR olFDDInetStatsRingOpCounts	1.3.6.1.4.1.49.2.3.1.5.4.4.1.2	Counter	read-only	The number times the ring transitioned to operational.
olFDDInetStatsTable	1.3.6.1.4.1.49.2.3.1.5.4.4		not-accessible	A table of statistical information counted for each FDDI network in the concentrator
CTR olFDDIStatsModBackplaneErrs	1.3.6.1.4.1.49.2.3.1.5.4.2.1.4	Counter	read-only	The number of errors while receiving and transmitting network data on the backplane.
olFDDIStatsModEntry	1.3.6.1.4.1.49.2.3.1.5.4.2.1		not-accessible	A list of statistical information for each module on each FDDI network in the concentrator.
CTR olFDDIStatsModMgtRcvErrs	1.3.6.1.4.1.49.2.3.1.5.4.2.1.2	Counter	read-only	The number of errors encountered while receiving data on the Management Channel.
CTR olFDDIStatsModMgtXmitErrs	1.3.6.1.4.1.49.2.3.1.5.4.2.1.3	Counter	read-only	The number of errors encountered while transmitting data on the Management Channel.
CTR olFDDIStatsModPllUnlockErrs	1.3.6.1.4.1.49.2.3.1.5.4.2.1.5	Counter	read-only	The number of times the phased lock loop on the backplane network data channel was lost.
INT olFDDIStatsModSlotIndex	1.3.6.1.4.1.49.2.3.1.5.4.2.1.1	INTEGER	read-only	The slot number that contains this module.
olFDDIStatsModTable	1.3.6.1.4.1.49.2.3.1.5.4.2		not-accessible	A table of statistical information counted for each module in each FDDI network.
olFDDIStatsPortEntry	1.3.6.1.4.1.49.2.3.1.5.4.3.1		not-accessible	A list of statistical information for each Port on each FDDI network in the concentrator.
INT olFDDIStatsPortIndex	1.3.6.1.4.1.49.2.3.1.5.4.3.1.2	INTEGER	read-only	The Port number of this port
CTR olFDDIStatsPortLCTFailCts	1.3.6.1.4.1.49.2.3.1.5.4.3.1.3	Counter	read-only	The count of the consecutive times the link confidence test (LCT) has failed during connection management. Once the connection has been established, the count is zeroed. (refer to ANSI 9.4.1).
CTR olFDDIStatsPortLemCts	1.3.6.1.4.1.49.2.3.1.5.4.3.1.6	Counter	read-only	The aggregate link error monitor error count, set to zero only on station power up. This variable's long term rate average is lerEstimate.
CTR olFDDIStatsPortLemRejectCts	1.3.6.1.4.1.49.2.3.1.5.4.3.1.5	Counter	read-only	A link error monitoring count of the times that a link has been removed from the ring due to the LerCutOff threshold being exceeded.
GAU olFDDIStatsPortLerEstimate	1.3.6.1.4.1.49.2.3.1.5.4.3.1.4	Gauge	read-only	A long term average link error rate. It ranges from 10-4 to 10-15 and is reported as the absolute value of the exponent of the estimate (the larger the number, the smaller the value).
INT olFDDIStatsPortSlotIndex	1.3.6.1.4.1.49.2.3.1.5.4.3.1.1	INTEGER	read-only	The slot number that contains this Port.
olFDDIStatsPortTable	1.3.6.1.4.1.49.2.3.1.5.4.3		not-accessible	A table of statistical information counted for each Port in each FDDI network.
olGroupPortEntry	1.3.6.1.4.1.49.2.3.1.6.1.1		not-accessible	The groups corresponding to a particular port.
OCT olGroupPortGroupID	1.3.6.1.4.1.49.2.3.1.6.1.1.3	OCTET STRING	read-only	The group(s) to which the port has been assigned.
INT olGroupPortIndex	1.3.6.1.4.1.49.2.3.1.6.1.1.2	INTEGER	read-only	The port number within this slot. Logical ports can not be put into groups.
INT olGroupPortSlotIndex	1.3.6.1.4.1.49.2.3.1.6.1.1.1	INTEGER	read-only	The slot number that contains this port.
olGroupPortTable	1.3.6.1.4.1.49.2.3.1.6.1		not-accessible	A list of groups that each port is in. Each port can can be in 0, 1, or many groups.
olGroups	1.3.6.1.4.1.49.2.3.1.6
olGroupSet	1.3.6.1.4.1.49.2.3.1.6.3
INT olGroupSetAction	1.3.6.1.4.1.49.2.3.1.6.3.1	INTEGER	read-write	This object specifies the action that we apply on a group. add-ports(1) adds port(s) to a group, clear-ports(2) clears (delete) port(s) from a group, and set-admin-state sets the Admin State of the group.
INT olGroupSetAdminState	1.3.6.1.4.1.49.2.3.1.6.3.5	INTEGER	read-write	This object specifies the Admin State that all the ports in the group defined by olGroupSetGroupID should be set to. This object should be set whenever set-admin-state(3) is selected for olGroupSetAction.
INT olGroupSetGroupID	1.3.6.1.4.1.49.2.3.1.6.3.2	INTEGER	read-write	A group index that uniquely identifies this group. A port can be in zero, one, or more groups.
INT olGroupSetPortIndex	1.3.6.1.4.1.49.2.3.1.6.3.4	INTEGER	read-write	This object specifies the port number of the port(s) that are to be added/cleared to/from the group. This object should be set whenever add-ports(1) or clear-ports(2) are selected for olGroupSetAction. Value 255 refers to all ports.
INT olGroupSetSlotIndex	1.3.6.1.4.1.49.2.3.1.6.3.3	INTEGER	read-write	This object specifies the slot number of the port(s) that are to be added/cleared to/from the group. This object should be set whenever add-ports(1) or clear-ports(2) are selected for olGroupSetAction. Value 254 refers to all non-existing ports, and value 255 refers to all slots which are only valid when olGroupSetAction is clear-ports(2).
olGroupSummaryEntry	1.3.6.1.4.1.49.2.3.1.6.2.1		not-accessible	The summary of all the ports in a particular group.
INT olGroupSummaryGroupID	1.3.6.1.4.1.49.2.3.1.6.2.1.1	INTEGER	read-only	The group to which the ports have been assigned. A port can be in one or more groups.
INT olGroupSummaryIndex	1.3.6.1.4.1.49.2.3.1.6.2.1.2	INTEGER	read-only	The index into the summary array. Up to 256 ports will be shown in olGroupSummaryPorts for each value in this entry.
OCT olGroupSummaryPorts	1.3.6.1.4.1.49.2.3.1.6.2.1.3	OCTET STRING	read-only	A condensed list of all the ports in this group. The summary is in the format: Slotx PortX SlotY PortY ...
olGroupSummaryTable	1.3.6.1.4.1.49.2.3.1.6.2		not-accessible	A table of condensed group information listing all the ports in each group.
INT olModClass	1.3.6.1.4.1.49.2.3.1.4.1.1.3	INTEGER	read-only	The class of this module. Generally speaking, this object indicates the kind of module. Specifically, the class identifier specifies the internal representation of the module's managed information base.
INT olModConfigToDips	1.3.6.1.4.1.49.2.3.1.4.1.1.8	INTEGER	read-write	Setting this object to configure(2) causes this module to configure based on the dip switch settings.
INT olModConfigured	1.3.6.1.4.1.49.2.3.1.4.1.1.9	INTEGER	read-only	This object indicates whether this module has already been configured. An unconfigured module is configured to a safe state where the network is isolated and the ports are disabled.
STR olModDescr	1.3.6.1.4.1.49.2.3.1.4.1.1.4	DisplayString	read-only	A textual string containing information about the module.
olModEntry	1.3.6.1.4.1.49.2.3.1.4.1.1		not-accessible	A list of information for each module in the concentrator.
INT olModNetwork	1.3.6.1.4.1.49.2.3.1.4.1.1.10	INTEGER	read-write	The network that this module is attached to. If the value is other(1) or port-switching(3), setting this object to a different value will generate the invalidData error. If the value is port-switching(3), manage the networks via the olPortNetwork object. The value per-connector(20) is returned if the managed module is a per-connector switchable and the connectors are on different networks. The connector networks are managed by the objects defined in the olSpecMods branch specified for this module. Modules and ports on the same network intercommunicate. Setting the module to isolated(2) (or other isolated values), removes this module from the backplane. Setting this module to a value that is not the same protocol type will return an invalidData error. Setting this module to a value that it does not support will return an invalidData error.
INT olModNetworkType	1.3.6.1.4.1.49.2.3.1.4.1.1.11	INTEGER	read-only	The network type of this module. port-switching(3) means that the network type differs depending on the port (like the router module). The network type reflects the valid values for olModNetwork.
INT olModNumPorts	1.3.6.1.4.1.49.2.3.1.4.1.1.13	INTEGER	read-only	The number of ports on this module. Note, ports may be physical ports like 10BASE-T ports, or logical, like the bridge module ports.
INT olModNumTrunks	1.3.6.1.4.1.49.2.3.1.4.1.1.14	INTEGER	read-only	The number of trunks on this module. Note, trunks are links that are, by definition, backbone connections. Examples of trunks are ring in and ring out ports for token ring, and the connections for rings to the backplane.
INT olModResetModule	1.3.6.1.4.1.49.2.3.1.4.1.1.7	INTEGER	read-write	Setting this object to reset(2) causes this module to reset.
INT olModSlotIndex	1.3.6.1.4.1.49.2.3.1.4.1.1.1	INTEGER	read-only	The unique slot number of this module. Its value ranges between 1 and olConcNumSlots and remains constant at least from one re-initialization of the entity's network management system to the next re-initialization.
INT olModStatus	1.3.6.1.4.1.49.2.3.1.4.1.1.12	INTEGER	read-only	The module's status.
olModSummaryEntry	1.3.6.1.4.1.49.2.3.1.4.5.1		not-accessible	A summary of all the generic and value added information associated with this module.
OCT olModSummaryInfo	1.3.6.1.4.1.49.2.3.1.4.5.1.2	OCTET STRING	read-only	A summary of all information relating to this module in condensed format. The condensed format is only as large as needed to hence the largest value which usually is one octet. The TCP port for the terminal server, however, uses 4 octets. The summary consists of a header, a module portion, a port portion, and a trunk portion. Each portion consists of generic information and module specific information. For example, the module information consists of the olModTable entry for this slot and the olSpecMods module table information for this module type for this slot. --------------------------------------------------- The header consists of the following octets: Version of structure : 1 Number of octets in generic module Number of octets in specific module Number of octets in generic port Number of octets in specific port Number of octets in generic trunk Number of octets in specific trunk The format of the data portion is as follows: Some of the olModTable: olModType olModClass olModDescr olModVersion olModNetwork olModNetworkType olModStatus olModNumPorts olModNumTrunks olSpecMods module table (for this module) Not including slot number. For each port: Some of the olPortTable: olPortType olPortConnector olPortStatus olPortAdminState olPortNetwork olPortNetworkType olSpecMods port table (for this port's module) Not including slot and port number. For each trunk: Some of the olTrunkTable: olTrunkType olTrunkConnector olTrunkStatus olTrunkAdminState olTrunkWrapState olTrunkNeighbor olSpecMods trunk table (for this trunk's module) Not including slot and trunk number. In all of the above, the index for all of these tables is condensed out of the summary.
INT olModSummarySlotIndex	1.3.6.1.4.1.49.2.3.1.4.5.1.1	INTEGER	read-only	The slot number of this module that this summary pertains to.
olModSummaryTable	1.3.6.1.4.1.49.2.3.1.4.5		not-accessible	A table of condensed module information.
olModTable	1.3.6.1.4.1.49.2.3.1.4.1		not-accessible	A table that contains generic information about every module that is present within the concentrator.
INT olModType	1.3.6.1.4.1.49.2.3.1.4.1.1.2	INTEGER	read-only	The unique type identifier for this module. This type is used to identify the branch in olSpecMods (see below). module-unmanageable(1) means that only the following objects are valid for this module: olModSlotIndex olModClass olModVersion olModVendor olModReset olModConfigToDips olModConfigured module-unknown(2) means that all the generic attributes are manageable, but there is no olSpecMods branch for this module as viewed by this agent.
olModules	1.3.6.1.4.1.49.2.3.1.4
INT olModVendor	1.3.6.1.4.1.49.2.3.1.4.1.1.6	INTEGER	read-only	The actual manufacturer of this board.
STR olModVersion	1.3.6.1.4.1.49.2.3.1.4.1.1.5	DisplayString	read-only	The software version number of this module.
olNet	1.3.6.1.4.1.49.2.3.1.5.1
INT olNetDPDataPath	1.3.6.1.4.1.49.2.3.1.5.1.1.1.1	INTEGER	read-only	The data path on the backplane. Data paths between different protocols overlap. That is, an ethernet data path will overlap with multiple token ring and fddi data paths.
olNetDPEntry	1.3.6.1.4.1.49.2.3.1.5.1.1.1		not-accessible	A list of information about each data path in the concentrator.
INT olNetDPNetID	1.3.6.1.4.1.49.2.3.1.5.1.1.1.2	INTEGER	read-only	The network that this data path corresponds to. If the data path is not being used at all, notUsed(1) is the return value. If the data path is being used by another protocol, then otherProto(2) is the return value.
olNetDPTable	1.3.6.1.4.1.49.2.3.1.5.1.1		not-accessible	A table that contains information linking physical backplane allocation to logical networks. This information is useful: (1) to determine the physical allocation of networks on the backplane, and (2) to determine the remaining capacity of the backplane for future network growth. Since unknown modules are managed via dip switches, this is useful in order to set the dips to the appropriate settings. Ethernet is a bus architecture. Once a path is allocated, all modules and ports can access that path. Token Ring and FDDI are ring architectures. Each module on a ring requires a path. Therefore, 4 paths could be used to link 4 modules together on one ring, or 2 modules on 2 separate rings. It is possible to have a module allocated to a ring (and thus a data path) without linking to another module. These rules can be used to determine the remaining capacity for network growth.
olNets	1.3.6.1.4.1.49.2.3.1.5
MAC olNetSecurityMACAddress	1.3.6.1.4.1.49.2.3.1.5.1.2.1.3	MacAddress	read-write	The security MAC address assigned to this port.
olNetSecurityMACEntry	1.3.6.1.4.1.49.2.3.1.5.1.2.1		not-accessible	A list of security configuration parameters and MAC addresses associated with each port with security configured in the concentrator.
INT olNetSecurityMACMode	1.3.6.1.4.1.49.2.3.1.5.1.2.1.4	INTEGER	read-write	The desired security mode for this port/address.
INT olNetSecurityMACPortIndex	1.3.6.1.4.1.49.2.3.1.5.1.2.1.2	INTEGER	read-only	The port number within this slot.
INT olNetSecurityMACSlotIndex	1.3.6.1.4.1.49.2.3.1.5.1.2.1.1	INTEGER	read-only	The slot number that contains this port.
INT olNetSecurityMACStatus	1.3.6.1.4.1.49.2.3.1.5.1.2.1.5	INTEGER	read-write	Each instance of the olNetSecurityMACTable associated with this olNetSecurityMACEntry (slot, port, and address) will be deleted by the agent if this olNetSecurityMACEntry is not equal to valid(1). Initial creation of instances occurs via a set operation on a specific slot/port/address.
olNetSecurityMACTable	1.3.6.1.4.1.49.2.3.1.5.1.2		not-accessible	A table of security configuration parameters and MAC addresses associated with every port with security configured in the concentrator.
INT olPortAdminState	1.3.6.1.4.1.49.2.3.1.4.2.1.6	INTEGER	read-write	The desired state of this port. Setting a port to be redundant-primary(3) or redundant-backup requires that the buddy slot and buddy port also be set to valid values (see appropriate olSpecMods objects). If the values associated with the redundant buddys are not valid, a genError will be returned. If the port is already redundant, an invalid set may result in both ports being disabled.
INT olPortConnector	1.3.6.1.4.1.49.2.3.1.4.2.1.4	INTEGER	read-only	The connector type of this port.
olPortEntry	1.3.6.1.4.1.49.2.3.1.4.2.1		not-accessible	A list of information about each port in the concentrator.
INT olPortIndex	1.3.6.1.4.1.49.2.3.1.4.2.1.2	INTEGER	read-only	The port number of this port within this module.
INT olPortNetwork	1.3.6.1.4.1.49.2.3.1.4.2.1.7	INTEGER	read-write	The network that this port is attached to. If the value of olPortNetwork is per-module(4), then use the olModNetwork to manage this port. Setting olPortNetwork to a different value in this case will generate the invalidData error. Setting this port to a value that is not the same protocol type will return invalidData error. front-panel(5) is used for modules that have a logical port and a physical front connection. An example of this is the Eth2Eth Bridge module. Setting this port to a value that it does not support will generate an invalidData error.
INT olPortNetworkType	1.3.6.1.4.1.49.2.3.1.4.2.1.8	INTEGER	read-only	The network type of this port. The type reflects the valid values for olPortNetwork.
INT olPortSlotIndex	1.3.6.1.4.1.49.2.3.1.4.2.1.1	INTEGER	read-only	The slot number of this port's module.
INT olPortStatus	1.3.6.1.4.1.49.2.3.1.4.2.1.5	INTEGER	read-only	The status of this port.
olPortTable	1.3.6.1.4.1.49.2.3.1.4.2		not-accessible	A table that contains generic information about each port on each module present within the concentrator.
INT olPortType	1.3.6.1.4.1.49.2.3.1.4.2.1.3	INTEGER	read-only	The type of port. logical(1) is used to manage port resources that may not map directly to physical connections. The OEBM, for example, has two logical ports, although those two ports can be assigned to different combinations of four physical connections. media(2) refers to ports such as those on the 10BASE-T module.
olSpecMods	1.3.6.1.4.1.49.2.3.1.4.4
olThresh	1.3.6.1.4.1.49.2.3.1.7.1
INT olThreshActionData	1.3.6.1.4.1.49.2.3.1.7.1.2.1.18	INTEGER	read-write	Additional information to be sent with the chipAboveThreshold trap. Provided for use by the network management station (NMS) - not interpreted by the agent. A network management station (NMS) could use olThreshActionData to specify an action to be performed by the NMS when the chipAboveThreshold trap is received.
INT olThreshActionPriority	1.3.6.1.4.1.49.2.3.1.7.1.2.1.19	INTEGER	read-write	The priority for this entry. Provided for use by the network management station (NMS) - not interpreted by the agent.
INT olThreshActionType	1.3.6.1.4.1.49.2.3.1.7.1.2.1.17	INTEGER	read-write	The action to be performed when the threshold is triggered.
INT olThreshAllMode	1.3.6.1.4.1.49.2.3.1.7.1.1.4	INTEGER	read-write	Provides the management station with a convenient way to set olThreshMode for all of the entries in ThreshTable. Setting olThreshAllMode to enable(1) or disable(2) will not cause new entries to be created; this will only affect entries that have presiously been created. Getting olThreshAllMode will always yield clear(3).
INT olThreshCondition	1.3.6.1.4.1.49.2.3.1.7.1.2.1.12	INTEGER	read-write	Specifies the type of conditional comparison for the threshold.
olThreshControl	1.3.6.1.4.1.49.2.3.1.7.1.1
INT olThreshCurrentValue	1.3.6.1.4.1.49.2.3.1.7.1.2.1.14	INTEGER	read-only	When olThreshType is delta-exceed(1): The most recent delta value of olThreshStatObjectIdentifier (i.e. value of olThreshStatObjectIdentifier at the end of the interval minus the value of olThreshStatObjectIdentifier at the beginning of the interval). If olThreshStatus is not valid(4), olThreshCurrentValue will be 0.
STR olThreshDescription	1.3.6.1.4.1.49.2.3.1.7.1.2.1.3	DisplayString	read-write	Description of the threshold to be sent with the chipAboveThreshold trap.
olThreshEntry	1.3.6.1.4.1.49.2.3.1.7.1.2.1		not-accessible	A collection of variables for controlling and monitoring a specific threshold.
INT olThreshIndex	1.3.6.1.4.1.49.2.3.1.7.1.2.1.1	INTEGER	read-only	An index that uniquely identifies an entry in the olThresh table. The number of entries in olTRThreshTable is olThreshTotalEntries. A new entry is created when a value is written to any object within the entry. An entry is removed when olThreshMode is set to clear(3). Index 255 references a 'pseudo entry' that allows the management station to create a new entry without having to search for a clear entry. When olThreshMode for entry 255 is set to disable or enable, if there is no available (clear) entry, then the SNMP set-response will indicate a bad value error, otherwise the agent does the following: - set the value of olThreshLastCreatedIndex to the index of the available entry - copy the values currently in entry 255 to the available entry - clear out entry 255.
INT olThreshInterval	1.3.6.1.4.1.49.2.3.1.7.1.2.1.11	INTEGER	read-write	Specifies the length of the thresholding period in seconds. Minimum length is 5 seconds; maximum is 86400 seconds (24 hours).
INT olThreshLastCreatedIndex	1.3.6.1.4.1.49.2.3.1.7.1.1.3	INTEGER	read-only	The index of the last entry in olThreshTable created via index 255 (see olThreshMode). If none, this value will be zero.
INT olThreshMaxEntries	1.3.6.1.4.1.49.2.3.1.7.1.1.2	INTEGER	read-only	The maximum number of entries in olThreshTable supported by this agent.
INT olThreshMode	1.3.6.1.4.1.49.2.3.1.7.1.2.1.2	INTEGER	read-write	The mode for this threshold. enable(1) indicates that this entry is in use and thresholding will be done. disable(2) indicates that this entry is in use but will no thresholding will be done. Setting olThreshMode to clear(3) will cause this entry to be removed from the table.
OID olThreshObjectIdentifier	1.3.6.1.4.1.49.2.3.1.7.1.2.1.4	OBJECT IDENTIFIER	read-write	The object identifier that specifies the statistic to be thresholded. The statistic to be thresholded can be specified either by setting olThreshObjectIdentifier or by setting values of the olThreshStat group of variables. When olThreshObjectIdentifier is set, the agent changes the values of the olThreshStat group of variables to refer to the new statistic to be thresholded. Similarly, when a olThreshStat variable is set, the agent changes olThreshObjectIdentifier to refer to the new statistic to be thresholded. A null object identifier (0.0) is used when no statistic is specified.
INT olThreshStatCategory	1.3.6.1.4.1.49.2.3.1.7.1.2.1.5	INTEGER	read-write	Specifies the category of statistic to be thresholded. When olThreshStatCategory is network(2) or station(4), olThreshStatNetID may also be specified. When olThreshStatCategory is station(4), olThreshStatStation must be specified. When olThreshStatCategory is port(3), olThreshStatSlotIndex and olThreshStatPortIndex must be specified.
INT olThreshStatNetID	1.3.6.1.4.1.49.2.3.1.7.1.2.1.7	INTEGER	read-write	When olThreshStatCategory is network(2) or station(4), specifies the network of statistic to be thresholded. If the agent is capable of collecting statistics only for the network that it is attached to, olThreshStatNetID can be set to agent-network(255); the agent will change olThreshStatNetID to reflect the network that the agent is currently attached to. If olThreshStatType is tr-net-soft-errors(7) or tr-net-hard-errors(8) the agent will change olThreshStatNetID to other(1).
INT olThreshStatPortIndex	1.3.6.1.4.1.49.2.3.1.7.1.2.1.9	INTEGER	read-write	When olThreshStatCategory is port(3), specifies the port index of the port of statistic to be thresholded.
INT olThreshStatSlotIndex	1.3.6.1.4.1.49.2.3.1.7.1.2.1.8	INTEGER	read-write	When olThreshStatCategory is port(3), specifies the slot index of the port of statistic to be thresholded.
MAC olThreshStatStationAddr	1.3.6.1.4.1.49.2.3.1.7.1.2.1.10	MacAddress	read-write	When olThreshStatCategory is station(4), specifies the MAC address of the station of statistic to be thresholded.
INT olThreshStatType	1.3.6.1.4.1.49.2.3.1.7.1.2.1.6	INTEGER	read-write	Specifies the type of statistic to be thresholded. error-frames(6) is valid only when olThreshStatCategory is port(3) or station(4). tr-net-soft-errors(7) or tr-net-hard-errors(8) is valid only when olThreshStatCategory is network(2). Note that tr-net-soft-errors(7) and tr-net-hard-errors(8) refer to dot5StatsSoftErrors and dot5StatsHardErrors, respectively. The other choices refer for items in the olTRTraf tables.
INT olThreshStatus	1.3.6.1.4.1.49.2.3.1.7.1.2.1.15	INTEGER	read-only	When olThreshType is delta-exceed(1): If olThreshStatObjectIdentifier has not yet been specified, olThreshStatus will be no-statistic-specified(1). If the first interval has not yet completed, olThreshStatus will be not-yet-available(2). If object referenced by olThreshStatObjectIdentifier is not accessible, olThreshStatus will be not-accessible(3). Otherwise olThreshStatus will be valid(4).
olThreshTable	1.3.6.1.4.1.49.2.3.1.7.1.2		not-accessible	A list of thresholding entries.
TIK olThreshTimeSinceLastTriggered	1.3.6.1.4.1.49.2.3.1.7.1.2.1.16	TimeTicks	read-only	Time in TimeTicks that has elapsed since a chipAboveThreshold trap associated with this ThreshEntry was last sent. If never sent, this value shall be zero.
INT olThreshTotalEntries	1.3.6.1.4.1.49.2.3.1.7.1.1.1	INTEGER	read-only	The number of entries currently in olThreshTable.
INT olThreshValue	1.3.6.1.4.1.49.2.3.1.7.1.2.1.13	INTEGER	read-write	At the end of each thresholding interval (olThreshInterval seconds), olThreshCurrentValue is compared against olThreshValue (unsigned). When olThreshType is delta-above(1): If olThreshStatus is valid(4), and olThreshCurrentValue is above olThreshValue, and olThreshMode is enabled, then a chipAboveThreshold trap will be sent. Another chipAboveThreshold trap will not be sent until olThreshCurrentValue drops to less than or equal to olThreshValue and then again exceeds it.
olTRnet	1.3.6.1.4.1.49.2.3.1.5.3
INT olTRnetMapState	1.3.6.1.4.1.49.2.3.1.5.3.1	INTEGER	read-only	The state of the inter-module token ring map. If the map is being updated, then the state of the map is changing.
olTRnetMapSummary	1.3.6.1.4.1.49.2.3.1.5.3.5
OCT olTRnetMapSummary32Stations	1.3.6.1.4.1.49.2.3.1.5.3.5.3.1.3	OCTET STRING	read-only	A concatonated group of MAC addresses and their associated slot and port of stations on the ring. Each entry has the eight octets. The first six octets are the MAC address. The seventh octet is the slot ID (or 255 if it is external to the concentrator). The eighth is the port ID (or 255 if it is external to the concentrator). The MAC addresses are in the same order as the token flow.
olTRnetMapSummaryEntry	1.3.6.1.4.1.49.2.3.1.5.3.5.3.1		not-accessible	A group of MAC addresses associated with a Token Ring map.
INT olTRnetMapSummaryIndex	1.3.6.1.4.1.49.2.3.1.5.3.5.3.1.2	INTEGER	read-only	The index into the map array. Possible values are 1 through 8. The MAC address of this agent is the first MAC address in olTRnetMapSummary32Stations indexed by a 1 in this entry.
INT olTRnetMapSummaryLogicalLock	1.3.6.1.4.1.49.2.3.1.5.3.5.2	INTEGER	read-write	A semaphore for locking the token ring summary table. When locked, updates to the summary will pend until the semaphore is unlocked, so that a valid summary can be read. This cannot be set to unlock if olTRnetSummaryLogicalState is changing. For complete accuracy, this should be read after being set to ensure that the map was not changing when the lock was attempted. After the summary information has been recorded, the semaphore should be set to unlock to allow changes to occur.
INT olTRnetMapSummaryLogicalState	1.3.6.1.4.1.49.2.3.1.5.3.5.1	INTEGER	read-only	The state of the token ring summary table. If the summary is being updated, then the state of the summary is changing.
INT olTRnetMapSummaryNetID	1.3.6.1.4.1.49.2.3.1.5.3.5.3.1.1	INTEGER	read-only	The network index that uniquely identifies this network. It can be isolated from the backplane, or on one of seven possible backplane token ring networks.
olTRnetMapSummaryTable	1.3.6.1.4.1.49.2.3.1.5.3.5.3		not-accessible	A logical map of the token ring network, starting from the agent's specified token ring interface. Each station on the map is represented by it's MAC address, slot number and port number (8 octets per station). If the port is external to the concentrator, the slot number will be 255 and the port number will be 0. The map is ordered in the same direction as the token flow. The MAC addresses are concatonated into groups of up to 32 addresses per entry. The last entry has all-zero MAC addresses padded on the end of the entry. All entries before the last one have 32 valid addresses. This table supports up to 256 stations.
CTR olTRnetStatsACErrors	1.3.6.1.4.1.49.2.3.1.5.3.2.1.4	Counter	read-only	The total number of AC (Address Copied) errors reported in error reporting packets detected by the TRMM.
INT olTRnetStatsActivePorts	1.3.6.1.4.1.49.2.3.1.5.3.2.1.19	INTEGER	read-only	The number of ports within this concentrator and on this ring which have olPortAdminState set to enabled and whose olPortStatus has a status of okay.
CTR olTRnetStatsBeaconEvents	1.3.6.1.4.1.49.2.3.1.5.3.2.1.10	Counter	read-only	The total number of times that the ring enters the beaconing state.
CTR olTRnetStatsBurstErrors	1.3.6.1.4.1.49.2.3.1.5.3.2.1.3	Counter	read-only	The total number of burst errors reported in error reporting packets detected by the TRMM.
INT olTRnetStatsConcStations	1.3.6.1.4.1.49.2.3.1.5.3.2.1.16	INTEGER	read-only	The number of stations currently participating in the 802.5 MAC protocol on the ring which are connected to ports in this concentrator.
CTR olTRnetStatsCongestionErrors	1.3.6.1.4.1.49.2.3.1.5.3.2.1.6	Counter	read-only	The total number of receive congestion errors reported in error reporting packets detected by the TRMM.
CTR olTRnetStatsDuplicateAddresses	1.3.6.1.4.1.49.2.3.1.5.3.2.1.9	Counter	read-only	The total number of token errors reported in error reporting packets detected by the TRMM.
INT olTRnetStatsEnabledPorts	1.3.6.1.4.1.49.2.3.1.5.3.2.1.18	INTEGER	read-only	The number of ports within this concentrator and on this ring which have olPortAdminState set to enabled.
olTRnetStatsEntry	1.3.6.1.4.1.49.2.3.1.5.3.2.1		not-accessible	A collection of statistics kept for a particular Token Ring interface.
CTR olTRnetStatsFrameCopiedErrors	1.3.6.1.4.1.49.2.3.1.5.3.2.1.7	Counter	read-only	The total number of frame copied errors reported in error reporting packets detected by the TRMM.
INT olTRnetStatsLastBeaconAction	1.3.6.1.4.1.49.2.3.1.5.3.2.1.14	INTEGER	read-only	The action (if any) taken to correct the last beacon event on the ring.
OCT olTRnetStatsLastBeaconNAUN	1.3.6.1.4.1.49.2.3.1.5.3.2.1.12	OCTET STRING	read-only	The address of the NAUN in the last beacon frame received on this ring. If no beacon frames have been received, this object will be six zero octets.
OCT olTRnetStatsLastBeaconSender	1.3.6.1.4.1.49.2.3.1.5.3.2.1.11	OCTET STRING	read-only	The address of the sender of the last beacon frame received on this ring. If no beacon frames have been received, this object will be six zero octets.
TIK olTRnetStatsLastBeaconTime	1.3.6.1.4.1.49.2.3.1.5.3.2.1.13	TimeTicks	read-only	The time in in hundredths of a second since the last beacon event occurred. For example, if the time is 500 ticks, then this event was seen 5 seconds ago. If no beacon events have occurred, then this will be equal to the sysUpTime.
CTR olTRnetStatsLineErrors	1.3.6.1.4.1.49.2.3.1.5.3.2.1.2	Counter	read-only	The total number of line errors reported in error reporting packets detected by the TRMM.
CTR olTRnetStatsLostFrameErrors	1.3.6.1.4.1.49.2.3.1.5.3.2.1.5	Counter	read-only	The total number of lost frame errors reported in error reporting packets detected by the TRMM.
INT olTRnetStatsNetID	1.3.6.1.4.1.49.2.3.1.5.3.2.1.1	INTEGER	read-only	The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated.
CTR olTRnetStatsPortACErrors	1.3.6.1.4.1.49.2.3.1.5.3.4.1.8	Counter	read-only	The total number of AC (Address Copied) errors pertaining to this port reported in error reporting packets detected by the TRMM.
OCT olTRnetStatsPortAddress	1.3.6.1.4.1.49.2.3.1.5.3.4.1.5	OCTET STRING	read-only	The mac address of the station connected to this If there are multiple mac addresses for this port, then this object will contain the last mac address.
CTR olTRnetStatsPortBurstErrors	1.3.6.1.4.1.49.2.3.1.5.3.4.1.7	Counter	read-only	The total number of burst errors pertaining to this port reported in error reporting packets detected by the TRMM.
CTR olTRnetStatsPortCongestionErrors	1.3.6.1.4.1.49.2.3.1.5.3.4.1.10	Counter	read-only	The total number of congestion errors pertaining to this port reported in error reporting packets detected by the TRMM.
CTR olTRnetStatsPortDuplicateAddresses	1.3.6.1.4.1.49.2.3.1.5.3.4.1.13	Counter	read-only	The number of times this port experienced a duplicate address error.
olTRnetStatsPortEntry	1.3.6.1.4.1.49.2.3.1.5.3.4.1		not-accessible	A collection of statistics for a particular station that has been discovered on a a ring monitored by this device.
CTR olTRnetStatsPortFrameCopiedErrors	1.3.6.1.4.1.49.2.3.1.5.3.4.1.11	Counter	read-only	The total number of frame copied errors pertaining to this port reported in error reporting packets detected by the TRMM.
INT olTRnetStatsPortIndex	1.3.6.1.4.1.49.2.3.1.5.3.4.1.2	INTEGER	read-only	The port number within olTRnetStatsPortSlotIndex's slot.
CTR olTRnetStatsPortLineErrors	1.3.6.1.4.1.49.2.3.1.5.3.4.1.6	Counter	read-only	The total number of Line Errors pertaining to this port reported in error reporting packets detected by the TRMM.
CTR olTRnetStatsPortLostFrameErrors	1.3.6.1.4.1.49.2.3.1.5.3.4.1.9	Counter	read-only	The total number of lost frame errors pertaining to this port reported in error reporting packets detected by the TRMM.
INT olTRnetStatsPortNetID	1.3.6.1.4.1.49.2.3.1.5.3.4.1.3	INTEGER	read-only	The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated.
INT olTRnetStatsPortSlotIndex	1.3.6.1.4.1.49.2.3.1.5.3.4.1.1	INTEGER	read-only	The port slot number.
olTRnetStatsPortTable	1.3.6.1.4.1.49.2.3.1.5.3.4		not-accessible	A list of statistic entries, for ports within the concentrator.
CTR olTRnetStatsPortTokenErrors	1.3.6.1.4.1.49.2.3.1.5.3.4.1.12	Counter	read-only	The total number of token errors pertaining to this station reported in error reporting packets detected by the TRMM.
INT olTRnetStatsPortTotalStations	1.3.6.1.4.1.49.2.3.1.5.3.4.1.4	INTEGER	read-only	The total number of stations attached to this port.
CTR olTRnetStatsStationACErrors	1.3.6.1.4.1.49.2.3.1.5.3.3.1.8	Counter	read-only	The total number of AC (Address Copied) errors pertaining to this station reported in error reporting packets detected by the TRMM.
OCT olTRnetStatsStationAddr	1.3.6.1.4.1.49.2.3.1.5.3.3.1.2	OCTET STRING	read-only	The physical address of this station.
CTR olTRnetStatsStationBurstErrors	1.3.6.1.4.1.49.2.3.1.5.3.3.1.7	Counter	read-only	The total number of burst errors pertaining to this station reported in error reporting packets detected by the TRMM.
CTR olTRnetStatsStationCongestionErrors	1.3.6.1.4.1.49.2.3.1.5.3.3.1.10	Counter	read-only	The total number of congestion errors pertaining to this station reported in error reporting packets detected by the TRMM.
CTR olTRnetStatsStationDuplicateAddresses	1.3.6.1.4.1.49.2.3.1.5.3.3.1.13	Counter	read-only	The number of times this station experienced a duplicate address error.
olTRnetStatsStationEntry	1.3.6.1.4.1.49.2.3.1.5.3.3.1		not-accessible	A collection of statistics for a particular station that has been discovered on a a ring monitored by this device.
CTR olTRnetStatsStationFrameCopiedErrors	1.3.6.1.4.1.49.2.3.1.5.3.3.1.11	Counter	read-only	The total number of frame copied errors pertaining to this station reported in error reporting packets detected by the TRMM.
CTR olTRnetStatsStationLineErrors	1.3.6.1.4.1.49.2.3.1.5.3.3.1.6	Counter	read-only	The total number of Line Errors pertaining to this station reported in error reporting packets detected by the TRMM.
CTR olTRnetStatsStationLostFrameErrors	1.3.6.1.4.1.49.2.3.1.5.3.3.1.9	Counter	read-only	The total number of lost frame errors pertaining to this station reported in error reporting packets detected by the TRMM.
OCT olTRnetStatsStationNAUNAddress	1.3.6.1.4.1.49.2.3.1.5.3.3.1.5	OCTET STRING	read-only	The physical address of the nearest active upstream neighbor of this station.
INT olTRnetStatsStationNetID	1.3.6.1.4.1.49.2.3.1.5.3.3.1.1	INTEGER	read-only	The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated.
INT olTRnetStatsStationPortIndex	1.3.6.1.4.1.49.2.3.1.5.3.3.1.4	INTEGER	read-only	The port number within olTRnetStatsStationSlotIndex's slot that received this address. If olTRnetStatsStationSlotIndex has a value of external(255), then the port address will be 255.
INT olTRnetStatsStationSlotIndex	1.3.6.1.4.1.49.2.3.1.5.3.3.1.3	INTEGER	read-only	The slot number of the station with this address. Addresses with a slot value of external(255) are not in this concentrator.
olTRnetStatsStationTable	1.3.6.1.4.1.49.2.3.1.5.3.3		not-accessible	A list of ring statistics entries.
CTR olTRnetStatsStationTokenErrors	1.3.6.1.4.1.49.2.3.1.5.3.3.1.12	Counter	read-only	The total number of token errors pertaining to this station reported in error reporting packets detected by the TRMM.
olTRnetStatsTable	1.3.6.1.4.1.49.2.3.1.5.3.2		not-accessible	A list of Token Ring statistics entries counted for each network.
CTR olTRnetStatsTokenErrors	1.3.6.1.4.1.49.2.3.1.5.3.2.1.8	Counter	read-only	The total number of token errors reported in error reporting packets detected by the TRMM.
INT olTRnetStatsTotalPorts	1.3.6.1.4.1.49.2.3.1.5.3.2.1.17	INTEGER	read-only	The total number of ports within this concentrator and on this ring regardless of their admin state or status.
INT olTRnetStatsTotalStations	1.3.6.1.4.1.49.2.3.1.5.3.2.1.15	INTEGER	read-only	The number of stations currently participating in the 802.5 MAC protocol on the ring.
CTR olTRTrafBroadcastFrames	1.3.6.1.4.1.49.2.3.1.5.3.6.1.8	Counter	read-only	The total number of non-MAC frames received that were directed to a broadcast address (0xFFFFFFFFFFFF or 0xC000FFFFFFFF).
INT olTRTrafControlClear	1.3.6.1.4.1.49.2.3.1.5.3.7.1.4	INTEGER	read-write	When the value of this object is set to clear, all entries in the token ring station traffic tables (olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable, and olTRTrafTopNSummaryTable) are cleared.
olTRTrafControlEntry	1.3.6.1.4.1.49.2.3.1.5.3.7.1		not-accessible	A collection of information about olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable, and olTRTrafTopNSummaryTable
TIK olTRTrafControlLastClearTime	1.3.6.1.4.1.49.2.3.1.5.3.7.1.5	TimeTicks	read-only	The value of sysUpTime when the token ring station traffic tables (olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable and olTRTrafTopNSummaryTable) were cleared. If never cleared, this value shall be zero (and the token ring station traffic tables will contain information collected since the XMM was started up).
INT olTRTrafControlLogicalLock	1.3.6.1.4.1.49.2.3.1.5.3.7.1.3	INTEGER	read-write	A semaphore for locking the token ring station traffic tables: olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable, and olTRTrafTopNSummaryTable. When the semaphore is locked, adds, deletes, and re-sorting the traffic tables associated with this olTRTrafControlEntry will pend until the semaphore is unlocked, so that a valid set of entries can be read. Note that the normal incrementing of the traffic counters are not affected by the setting of this semaphore. This cannot be set to unlock if olTRTrafControlLogicalState is changing. For complete accuracy, this semaphore should be read after being set to ensure that the tables were not changing when the lock was attempted. After the table information has been recorded, the semaphore should be set to unlock to allow changes to occur.
INT olTRTrafControlLogicalState	1.3.6.1.4.1.49.2.3.1.5.3.7.1.2	INTEGER	read-only	The state of the token ring station traffic tables: olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable and olTRTrafTopNSummaryTable. If any of the tables associated with this olTRTrafControlEntry are being updated, then the state is changing(1).
INT olTRTrafControlNetID	1.3.6.1.4.1.49.2.3.1.5.3.7.1.1	INTEGER	read-only	The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated.
TIK olTRTrafControlPortLastChangeTime	1.3.6.1.4.1.49.2.3.1.5.3.7.1.9	TimeTicks	read-only	The value of sysUpTime when the last entry was added to or deleted (or re-sorted) from the portion of the olTRTrafPortTable associated with this olTRTrafControlEntry. If no additions or deletions have occurred, this value shall be zero.
INT olTRTrafControlPortTotalStations	1.3.6.1.4.1.49.2.3.1.5.3.7.1.8	INTEGER	read-only	The number of stations in the portion of the olTRTrafPortTable associated with this olTRTrafControlEntry.
TIK olTRTrafControlStationLastChangeTime	1.3.6.1.4.1.49.2.3.1.5.3.7.1.7	TimeTicks	read-only	The value of sysUpTime when the last entry was added to or deleted (or re-sorted) from the portion of the olTRTrafStationTable associated with this olTRTrafControlEntry. If no additions or deletions have occurred, this value shall be zero.
olTRTrafControlTable	1.3.6.1.4.1.49.2.3.1.5.3.7		not-accessible	A list entries containing information about olTRTrafStationTable, olTRTrafPortTable, olTRTrafTopNTable, and olTRTrafTopNSummaryTable
INT olTRTrafControlTopNInterval	1.3.6.1.4.1.49.2.3.1.5.3.7.1.13	INTEGER	read-write	Specifies the length of the TopN data collection period in seconds. Minimum length is 5 seconds; maximum is 86400 seconds (24 hours). When this value is modified, all associated entries in olTRTrafTopNTable and olTRTrafTopNSummaryTable are deleted and a new TopN data collection period is started.
TIK olTRTrafControlTopNLastChangeTime	1.3.6.1.4.1.49.2.3.1.5.3.7.1.12	TimeTicks	read-only	The value of sysUpTime when the last entry was added to or deleted (or re-sorted) from the portion of the olTRTrafTopNTable and olTRTrafTopNSummaryTable associated with this olTRTrafControlEntry. This is equivalent to the time when the last TopN data collection period ended. If no additions or deletions have occurred, this value shall be zero.
INT olTRTrafControlTopNMaxStations	1.3.6.1.4.1.49.2.3.1.5.3.7.1.10	INTEGER	read-write	Specifies a maximum value for olTRTrafControlTopNTotalStations in this olTRTrafControlEntry. If this value is zero then no maximum value for olTRTrafControlTopNTotalStations is specified.
INT olTRTrafControlTopNTotalStations	1.3.6.1.4.1.49.2.3.1.5.3.7.1.11	INTEGER	read-only	The number of stations (for each statistic) in the portion of the olTRTrafTopNTable and olTRTrafTopNSummaryTable associated with this olTRTrafControlEntry. If olTRTrafControlTopNMaxStations is zero or is not less than olTRTrafControlTotalStations then olTRTrafControlTopNTotalStations will have the same value as olTRTrafControlTotalStations. Otherwise olTRTrafControlTopNTotalStations will have the same value as olTRTrafControlTopNMaxStations.
INT olTRTrafControlTotalStations	1.3.6.1.4.1.49.2.3.1.5.3.7.1.6	INTEGER	read-only	The number of stations in the portion of the olTRTrafStationTable associated with this olTRTrafControlEntry.
CTR olTRTrafDropEvents	1.3.6.1.4.1.49.2.3.1.5.3.6.1.3	Counter	read-only	The total number of events in which frames were dropped by the TRMM due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
olTRTrafEntry	1.3.6.1.4.1.49.2.3.1.5.3.6.1		not-accessible	A collection of statistics kept for a particular Token Ring interface. Note that all of the frame and octet counters in this table include error frames that have valid length; all octet counters exclude framing bits but include FCS octets.
CTR olTRTrafFrames	1.3.6.1.4.1.49.2.3.1.5.3.6.1.5	Counter	read-only	The total number of frames received.
CTR olTRTrafFrames1024to2047Octets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.15	Counter	read-only	The total number of non-MAC frames received that were between 1024 and 2047 octets in length inclusive.
CTR olTRTrafFrames128to255Octets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.12	Counter	read-only	The total number of non-MAC frames received that were between 128 and 255 octets in length inclusive.
CTR olTRTrafFrames18to63Octets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.10	Counter	read-only	The total number of non-MAC frames received that were between 18 and 63 octets in length inclusive.
CTR olTRTrafFrames2048to4095Octets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.16	Counter	read-only	The total number of non-MAC frames received that were between 2048 and 4095 octets in length inclusive.
CTR olTRTrafFrames256to511Octets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.13	Counter	read-only	The total number of non-MAC frames received that were between 256 and 511 octets in length inclusive.
CTR olTRTrafFrames4096to8191Octets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.17	Counter	read-only	The total number of non-MAC frames received that were between 4096 and 8191 octets in length inclusive.
CTR olTRTrafFrames512to1023Octets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.14	Counter	read-only	The total number of non-MAC frames received that were between 512 and 1023 octets in length inclusive.
CTR olTRTrafFrames64to127Octets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.11	Counter	read-only	The total number of non-MAC frames received that were between 64 and 127 octets in length inclusive.
CTR olTRTrafFrames8192to18000Octets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.18	Counter	read-only	The total number of non-MAC frames received that were between 8192 and 18000 octets in length inclusive.
CTR olTRTrafFramesGreaterThan18000Octets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.19	Counter	read-only	The total number of non-MAC frames received that were greater than or equal to 18000 octets in length.
CTR olTRTrafMacFrames	1.3.6.1.4.1.49.2.3.1.5.3.6.1.7	Counter	read-only	The total number of MAC frames received.
CTR olTRTrafMacOctets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.6	Counter	read-only	The total number of octets of data in MAC frames received on the network.
CTR olTRTrafMulticastFrames	1.3.6.1.4.1.49.2.3.1.5.3.6.1.9	Counter	read-only	The total number of non-MAC frames received that were directed to a local or global multicast or functional address. Note that this number does not include frames directed to a broadcast address.
INT olTRTrafNetID	1.3.6.1.4.1.49.2.3.1.5.3.6.1.1	INTEGER	read-only	The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated.
CTR olTRTrafOctets	1.3.6.1.4.1.49.2.3.1.5.3.6.1.4	Counter	read-only	The total number of octets of data received on the network.
MAC olTRTrafPortAddress	1.3.6.1.4.1.49.2.3.1.5.3.9.1.4	MacAddress	read-only	The physical address of this station.
olTRTrafPortEntry	1.3.6.1.4.1.49.2.3.1.5.3.9.1		not-accessible	A collection of station statistics for a particular station that has been discovered on an interface of this device. Note that all of the frame and octet counters in this table include error frames that have valid length; all octet counters exclude framing bits but include FCS octets. include error frames; all octet counters exclude framing bits but include FCS octets.
CTR olTRTrafPortInFrames	1.3.6.1.4.1.49.2.3.1.5.3.9.1.5	Counter	read-only	The number of frames transmitted to this address since it was added to this table.
CTR olTRTrafPortInOctets	1.3.6.1.4.1.49.2.3.1.5.3.9.1.7	Counter	read-only	The number of octets transmitted to this address since it was added to this table.
INT olTRTrafPortNetID	1.3.6.1.4.1.49.2.3.1.5.3.9.1.3	INTEGER	read-only	The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated.
CTR olTRTrafPortOutBroadcastFrames	1.3.6.1.4.1.49.2.3.1.5.3.9.1.10	Counter	read-only	The number of frames transmitted by this address that were directed to the broadcast address since it was added to this table.
CTR olTRTrafPortOutErrors	1.3.6.1.4.1.49.2.3.1.5.3.9.1.9	Counter	read-only	The number of error frames transmitted by this address since it was added to this table. Only isolating errors (LineErrors, BurstErrors, ACErrors, InternalErrors, and AbortErrors) and CongestionErrors are counted.
CTR olTRTrafPortOutFrames	1.3.6.1.4.1.49.2.3.1.5.3.9.1.6	Counter	read-only	The number of frames transmitted by this address since it was added to this table.
CTR olTRTrafPortOutMulticastFrames	1.3.6.1.4.1.49.2.3.1.5.3.9.1.11	Counter	read-only	The number of frames transmitted by this address that were directed to a multicast address since it was added to this table. Note that this number does not include frames directed to the broadcast address.
CTR olTRTrafPortOutOctets	1.3.6.1.4.1.49.2.3.1.5.3.9.1.8	Counter	read-only	The number of octets transmitted by this address since it was added to this table.
INT olTRTrafPortPortIndex	1.3.6.1.4.1.49.2.3.1.5.3.9.1.2	INTEGER	read-only	The port number within olTRTrafPortSlotIndex's slot that received this address.
INT olTRTrafPortSlotIndex	1.3.6.1.4.1.49.2.3.1.5.3.9.1.1	INTEGER	read-only	The slot number of the station with this address.
olTRTrafPortTable	1.3.6.1.4.1.49.2.3.1.5.3.9		not-accessible	A list of Token Ring station traffic statistics entries indexed by slot number, and port number. Note that stations external to this concentrator or on another ring are excluded from this table. Note that all of the frame and octet counters in this table include error frames that have valid length; all octet counters exclude framing bits but include FCS octets.
MAC olTRTrafStationAddress	1.3.6.1.4.1.49.2.3.1.5.3.8.1.2	MacAddress	read-only	The physical address of this station.
olTRTrafStationEntry	1.3.6.1.4.1.49.2.3.1.5.3.8.1		not-accessible	A collection of station statistics for a particular station that has been discovered on an interface of this device. Note that all of the frame and octet counters in this table include error frames that have valid length; all octet counters exclude framing bits but include FCS octets.
CTR olTRTrafStationInFrames	1.3.6.1.4.1.49.2.3.1.5.3.8.1.5	Counter	read-only	The number of frames transmitted to this address since it was added to this table.
CTR olTRTrafStationInOctets	1.3.6.1.4.1.49.2.3.1.5.3.8.1.7	Counter	read-only	The number of octets transmitted to this address since it was added to this table.
INT olTRTrafStationNetID	1.3.6.1.4.1.49.2.3.1.5.3.8.1.1	INTEGER	read-only	The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated.
CTR olTRTrafStationOutBroadcastFrames	1.3.6.1.4.1.49.2.3.1.5.3.8.1.10	Counter	read-only	The number of frames transmitted by this address that were directed to the broadcast address since it was added to this table.
CTR olTRTrafStationOutErrors	1.3.6.1.4.1.49.2.3.1.5.3.8.1.9	Counter	read-only	The number of error frames transmitted by this address since it was added to this table. Only isolating errors (LineErrors, BurstErrors, ACErrors, InternalErrors, and AbortErrors) and CongestionErrors are counted.
CTR olTRTrafStationOutFrames	1.3.6.1.4.1.49.2.3.1.5.3.8.1.6	Counter	read-only	The number of frames transmitted by this address since it was added to this table.
CTR olTRTrafStationOutMulticastFrames	1.3.6.1.4.1.49.2.3.1.5.3.8.1.11	Counter	read-only	The number of frames transmitted by this address that were directed to a multicast address since it was added to this table. Note that this number does not include frames directed to the broadcast address.
CTR olTRTrafStationOutOctets	1.3.6.1.4.1.49.2.3.1.5.3.8.1.8	Counter	read-only	The number of octets transmitted by this address since it was added to this table.
INT olTRTrafStationPortIndex	1.3.6.1.4.1.49.2.3.1.5.3.8.1.4	INTEGER	read-only	The port number within olTRTrafSlotIndex's slot that received this address. If olTRTrafSlotIndex has a value of remote-ring(254), then the port address will be 254. If olTRTrafSlotIndex has a value of external(255), then the port address will be 255.
INT olTRTrafStationSlotIndex	1.3.6.1.4.1.49.2.3.1.5.3.8.1.3	INTEGER	read-only	The slot number of the station with this address. Addresses with a slot value of remote-ring(254) are not in this ring. Addresses with a slot value of external(255) are not in this concentrator.
olTRTrafStationTable	1.3.6.1.4.1.49.2.3.1.5.3.8		not-accessible	A list of Token Ring station traffic statistics entries indexed by Network ID and MAC address. The table has olTRTrafTotalStations entries. Note that all of the frame and octet counters in this table include error frames that have valid length; all octet counters exclude framing bits but include FCS octets.
olTRTrafTable	1.3.6.1.4.1.49.2.3.1.5.3.6		not-accessible	A list of Token Ring network traffic (non-error) statistics entries. Note that all of the frame and octet counters in this table include error frames that have valid length; all octet counters exclude framing bits but include FCS octets.
INT olTRTrafTokenRotationTime	1.3.6.1.4.1.49.2.3.1.5.3.6.1.2	INTEGER	read-only	An estimate of the time (in microseconds) that it takes for the token to complete a single rotation around the ring.
MAC olTRTrafTopNAddress	1.3.6.1.4.1.49.2.3.1.5.3.10.1.4	MacAddress	read-only	The physical address of this station.
olTRTrafTopNEntry	1.3.6.1.4.1.49.2.3.1.5.3.10.1		not-accessible	A collection of station statistics for a particular station that has been discovered on an interface of this device. Note that all of the frame and octet counters in this table include error frames that have valid length; all octet counters exclude framing bits but include FCS octets.
INT olTRTrafTopNIndex	1.3.6.1.4.1.49.2.3.1.5.3.10.1.3	INTEGER	read-only	An index that uniquely identifies an entry in the olTRTrafTopN table among those in the same network and for the same olTRTrafTopNStatistic. This index is between 1 and N, where N is the value of olTRTrafControlTopNTotalStations. Increasing values of olTRTrafTopNIndex shall be assigned to entries with decreasing values of the object referenced by olTRTrafTopNStatistic.
CTR olTRTrafTopNInFrames	1.3.6.1.4.1.49.2.3.1.5.3.10.1.7	Counter	read-only	The number of frames transmitted to this address during the last TopN data collection period.
CTR olTRTrafTopNInOctets	1.3.6.1.4.1.49.2.3.1.5.3.10.1.9	Counter	read-only	The number of octets transmitted to this address during the last TopN data collection period.
INT olTRTrafTopNNetID	1.3.6.1.4.1.49.2.3.1.5.3.10.1.1	INTEGER	read-only	The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated.
CTR olTRTrafTopNOutBroadcastFrames	1.3.6.1.4.1.49.2.3.1.5.3.10.1.12	Counter	read-only	The number of frames transmitted by this address that were directed to the broadcast address during the last TopN data collection period.
CTR olTRTrafTopNOutErrors	1.3.6.1.4.1.49.2.3.1.5.3.10.1.11	Counter	read-only	The number of error frames transmitted by this address during the last TopN data collection period. Only isolating errors (LineErrors, BurstErrors, ACErrors, InternalErrors, and AbortErrors) and CongestionErrors are counted.
CTR olTRTrafTopNOutFrames	1.3.6.1.4.1.49.2.3.1.5.3.10.1.8	Counter	read-only	The number of frames transmitted by this address during the last TopN data collection period.
CTR olTRTrafTopNOutMulticastFrames	1.3.6.1.4.1.49.2.3.1.5.3.10.1.13	Counter	read-only	The number of frames transmitted by this address that were directed to a multicast address during the last TopN data collection period. Note that this number does not include frames directed to the broadcast address.
CTR olTRTrafTopNOutOctets	1.3.6.1.4.1.49.2.3.1.5.3.10.1.10	Counter	read-only	The number of octets transmitted by this address during the last TopN data collection period.
INT olTRTrafTopNPortIndex	1.3.6.1.4.1.49.2.3.1.5.3.10.1.6	INTEGER	read-only	The port number within olTRTrafTopNSlotIndex's slot that received this address. If olTRTrafTopNSlotIndex has a value of remote-ring(254), then the port address will be 254. If olTRTrafTopNSlotIndex has a value of external(255), then the port address will be 255.
INT olTRTrafTopNSlotIndex	1.3.6.1.4.1.49.2.3.1.5.3.10.1.5	INTEGER	read-only	The slot number of the station with this address. Addresses with a slot value of remote-ring(254) are not in this ring. Addresses with a slot value of external(255) are not in this concentrator.
INT olTRTrafTopNStatistic	1.3.6.1.4.1.49.2.3.1.5.3.10.1.2	INTEGER	read-write	The object representing the statistic for each station that this portion of the olTRTrafTopNTable is sorted on.
olTRTrafTopNSummaryEntry	1.3.6.1.4.1.49.2.3.1.5.3.11.1		not-accessible	A segment of the Top N list for a particular statistic.
INT olTRTrafTopNSummaryIndex	1.3.6.1.4.1.49.2.3.1.5.3.11.1.3	INTEGER	read-only	An index that uniquely identifies an entry in the olTRTrafTopNSummary table among those in the same network and for the same olTRTrafTopNSummaryStatistic. The number of entries for this portion of olTRTrafTopNSummaryTable is number of entries for the corresponding portion of olTRTrafTopNTable divided by 12 (rounded up to the next integer).
INT olTRTrafTopNSummaryNetID	1.3.6.1.4.1.49.2.3.1.5.3.11.1.1	INTEGER	read-only	The network index that uniquely identifies this network. One of token-ring-1 through token-ring-7 or isolated.
OCT olTRTrafTopNSummaryStations	1.3.6.1.4.1.49.2.3.1.5.3.11.1.4	OCTET STRING	read-only	A concatonated list of (up to 12) MAC addresses, their associated slot and port, and a statistic value for traffic associated with stations on the ring. Each entry has 36 octets. The first 6 octets are the MAC address. The 7th octet is the slot ID (or 255 if it is external to the concentrator or 254 if it is on a remote ring). The 8th is the port ID (or 255 if it is external to the concentrator or 254 if it is on a remote ring). The 9th through 36th octets contain the values of the statistics olTRTrafTopNInFrames, olTRTrafTopNOutFrames, olTRTrafTopNInOctets, olTRTrafTopNOutOctets, olTRTrafTopNOutErrors, olTRTrafTopNOutBroadcastFrames, and olTRTrafTopNOutMulticastFrames. Each statistic is represented in 4 octets, most significant octet first. The stations are in order of decreasing values of the statistic referenced by olTRTrafTopNStatistic.
INT olTRTrafTopNSummaryStatistic	1.3.6.1.4.1.49.2.3.1.5.3.11.1.2	INTEGER	read-write	The object representing the statistic for each station that this portion of the olTRTrafTopNSummaryTable is sorted on.
olTRTrafTopNSummaryTable	1.3.6.1.4.1.49.2.3.1.5.3.11		not-accessible	A list containing information from olTRTrafTopNTable provided for the convenience of network management stations that wish to obtain this information in condensed form.
olTRTrafTopNTable	1.3.6.1.4.1.49.2.3.1.5.3.10		not-accessible	A list of Token Ring station traffic statistics entries indexed by olTRTrafTopNNetID, olTRTrafTopNStatistic, and olTRTrafTopNIndex. For each Network, the list contains 7 logical sublists - one for each statistic. Each of the sublists has olTRTrafControlTopNTotalStations entries. For eack Network, the table has 7 times olTRTrafTopNControlTotalStations entries. All of the counters in this table reflect activity during the last completed TopN data collection period (olTRTrafControlTopNInterval seconds). Note that this table will contain no entries if a TopN data collection period has not yet completed since olTRTrafControlTopNInterval was modified or since startup. Note that all of the frame and octet counters in this table include error frames that have valid length; all octet counters exclude framing bits but include FCS octets.
INT olTrunkAdminState	1.3.6.1.4.1.49.2.3.1.4.3.1.6	INTEGER	read-write	The desired state of this trunk. Enabling a trunk allows the trunk to pass network traffic.
INT olTrunkConnector	1.3.6.1.4.1.49.2.3.1.4.3.1.4	INTEGER	read-only	The connector type of this trunk.
olTrunkEntry	1.3.6.1.4.1.49.2.3.1.4.3.1		not-accessible	A list of information about each trunk in the concentrator.
INT olTrunkIndex	1.3.6.1.4.1.49.2.3.1.4.3.1.2	INTEGER	read-only	The trunk number of this trunk.
INT olTrunkNeighbor	1.3.6.1.4.1.49.2.3.1.4.3.1.8	INTEGER	read-only	The upstream or downstream neighbor of the trunk.
INT olTrunkSlotIndex	1.3.6.1.4.1.49.2.3.1.4.3.1.1	INTEGER	read-only	The slot number of this trunk's module.
INT olTrunkStatus	1.3.6.1.4.1.49.2.3.1.4.3.1.5	INTEGER	read-only	The status of this trunk.
olTrunkTable	1.3.6.1.4.1.49.2.3.1.4.3		not-accessible	A table that contains generic information about each trunk on each module present within the concentrator.
INT olTrunkType	1.3.6.1.4.1.49.2.3.1.4.3.1.3	INTEGER	read-only	The type of trunk. ringIn(3) and ringOut(4) refer to special trunks on the token ring protocol type modules.
INT olTrunkWrapState	1.3.6.1.4.1.49.2.3.1.4.3.1.7	INTEGER	read-only	The wrap state of this trunk. A trunk can wrap in response to a network event such as a break in the cable.
online	1.3.6.1.4.1.49.2.3.1
portGroup	1.3.6.1.4.1.49.2.3.4.6
softwareGroup	1.3.6.1.4.1.49.2.3.4.3
trmm	1.3.6.1.4.1.49.2.3.7
workGroupHub	1.3.6.1.4.1.49.2.3.4

RFC description

Chipcom network device MIB providing management objects for Chipcom bridge and network equipment monitoring

Start monitoring Chipcom (3Com) Ethernet/Token Ring switching hub or LAN concentrator (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CHIPCOM-MIB

What Is CHIPCOM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description