All MIBs › CDR-TRAP-MIB
Organization: Lucent Technologies
Last Updated: 240701
Category: Alarm and Event Management
Description: Defines SNMP trap notifications for CDR/Kentrox channel service unit fault conditions and alarm events.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CDR-TRAP-MIB?
CDR-TRAP-MIB is a vendor-specific MIB, per its short description, from Kentrox/CDR covering channel service unit (CSU) equipment, defining SNMP trap notifications for fault conditions and alarm events. As no concrete sample objects were provided and the module description is a generic placeholder, its exact trap variable bindings are unconfirmed, but its purpose is to notify a management station asynchronously of CSU faults such as line alarms, loss of signal, or loopback state changes. Its monitoring value is centered on hardware fault/alarm status of the CSU line interface, letting an operator detect line-level failures without needing to continuously poll. It likely complements a corresponding CDR/Kentrox CSU configuration MIB that defines the underlying status objects referenced by these traps, though this cannot be confirmed without further detail. It would be deployed on Kentrox/CDR channel service unit hardware terminating leased digital lines (e.g., T1/E1) in enterprise or carrier network environments. Engineers can download the CDR-TRAP-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CDR-TRAP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Lucent SoftSwitch CDR (Call Detail Record) Device Server
Monitoring Examples
No sample_objects were provided for this MIB, and the module description is a placeholder, so specific trap names cannot be cited with confidence; based on the short description, a plausible use would be a management station receiving traps for CSU line alarm or loss-of-signal conditions, but exact object identifiers cannot be verified here.
What Can Be Monitored
- line alarm/fault notifications
- loss of signal events
- CSU alarm status changes
Imported Objects
From CDR-DS1-MIB
| callAnswerTime | OBJECT-TYPE |
| callId | OBJECT-TYPE |
| cdrCallState | |
| cdrClient | OBJECT-TYPE |
| destinationNumber | OBJECT-TYPE |
| errorNo | |
| fCAppID | OBJECT-TYPE |
| fCAppInstance | OBJECT-TYPE |
| fileName | |
| fileSystem | OBJECT-TYPE |
| fullPercent | OBJECT-TYPE |
| originationNumber | OBJECT-TYPE |
| severity | OBJECT-TYPE |
| subType | |
| switchId | OBJECT-TYPE |
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| enterprises |
From RFC1213-MIB
| DisplayString |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| ObjectName | |
| snmpModules |
From SNMPv2-TC
| RowStatus | |
| TestAndIncr | |
| TimeStamp | |
| TruthValue |
OIDs
RFC description
Defines SNMP trap notifications for call detail recording (CDR) device server events.
Start monitoring Lucent SoftSwitch CDR (Call Detail Record) Device Server with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.