Brcm-adapterInfo-MIB

All MIBs › Brcm-adapterInfo-MIB

Category: Vendor: Broadcom

Description: Provides hardware inventory and configuration information for Broadcom NIC adapters installed in server systems.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Brcm-adapterInfo-MIB?

Brcm-adapterInfo-MIB is a Broadcom vendor MIB that reports hardware inventory and configuration information for Broadcom network interface card (NIC) adapters installed in server systems. It is intended to expose identification and configuration data about each adapter, such as model, firmware/driver version, and port configuration, though no concrete sample objects were available to ground specific leaf names for this module. Its relevance to monitoring is primarily hardware inventory and software version status: a MIB of this kind is typically used to confirm which NIC hardware and firmware/driver revision is installed, supporting asset tracking and version-compliance checks rather than real-time performance counters. It is a self-contained Broadcom vendor MIB, likely used alongside standard interface MIBs for the same adapters rather than depending on them. It is deployed on servers equipped with Broadcom NICs, typically polled by server management/asset-inventory tooling. Engineers can download the Brcm-adapterInfo-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Brcm-adapterInfo-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Server with Broadcom network interface card (NIC)

Monitoring Examples

No concrete object or table names were supplied in sample_objects for this module, so a specific monitoring scenario cannot be grounded in real data. In general, a NIC adapter-info MIB of this type would let an administrator confirm installed adapter model and firmware/driver version to catch an unexpected or out-of-date NIC in a server fleet, but the specific objects that would be polled cannot be stated without further data on this module.

Imported Objects

From RFC1155-SMI

Counter
OBJECT-TYPE
enterprises

From RFC1213-MIB

DisplayString
PhysAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
broadcom	1.3.6.1.4.1.4413
enet	1.3.6.1.4.1.4413.1
basp	1.3.6.1.4.1.4413.1.2
baspConfig	1.3.6.1.4.1.4413.1.2.1
baspStat	1.3.6.1.4.1.4413.1.2.2
baspTrap	1.3.6.1.4.1.4413.1.2.3
ifControllers	1.3.6.1.4.1.4413.1.3
INT ifNumber	1.3.6.1.4.1.4413.1.3.1	INTEGER	read-only	The number of Broadcom network interfaces (regardless of their current state) present on this system.
ifTable	1.3.6.1.4.1.4413.1.3.2		not-accessible	A list of Broadcom network interface entries. The number of entries is given by the ifNumber.
ifEntry	1.3.6.1.4.1.4413.1.3.2.1		not-accessible	An entry containing statistics objects of a Broadcom network interface in this system.
INT ifIndex	1.3.6.1.4.1.4413.1.3.2.1.1	INTEGER	read-only	An unique value for each Broadcom interface. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
STR ifName	1.3.6.1.4.1.4413.1.3.2.1.2	DisplayString	read-only	A textual string containing name of the adapter or team
STR ifDescr	1.3.6.1.4.1.4413.1.3.2.1.3	DisplayString	read-only	A textual string containing the adapter or team description
IP ifNetworkAddress	1.3.6.1.4.1.4413.1.3.2.1.4	IpAddress	read-only	IP address of the adapter.
IP ifSubnetMask	1.3.6.1.4.1.4413.1.3.2.1.5	IpAddress	read-only	IP subnet Mask of the adapter.
PHY ifPhysAddress	1.3.6.1.4.1.4413.1.3.2.1.6	PhysAddress	read-only	MAC address of the adapter.
PHY ifPermPhysAddress	1.3.6.1.4.1.4413.1.3.2.1.7	PhysAddress	read-only	Permanent MAC address of the adapter.
INT ifLinkStatus	1.3.6.1.4.1.4413.1.3.2.1.8	INTEGER	read-only	Adapter link status, this information only applicable to the Broadcom adapter
INT ifState	1.3.6.1.4.1.4413.1.3.2.1.9	INTEGER	read-only	The operating mode of the driver, this information only applicable to the Broadcom adapter
INT ifLineSpeed	1.3.6.1.4.1.4413.1.3.2.1.10	INTEGER	read-only	The operating speed of the adapter, this information only applicable to the Broadcom adapter
INT ifDuplexMode	1.3.6.1.4.1.4413.1.3.2.1.11	INTEGER	read-only	Adapter duplex mode, this information only applicable to the Broadcom adapter
STR ifMemBaseLow	1.3.6.1.4.1.4413.1.3.2.1.12	DisplayString	read-only	memory low range of the adapter, this information only applicable to the Broadcom adapter
STR ifMemBaseHigh	1.3.6.1.4.1.4413.1.3.2.1.13	DisplayString	read-only	memory high range of the adapter, this information only applicable to the Broadcom adapter
INT ifInterrupt	1.3.6.1.4.1.4413.1.3.2.1.14	INTEGER	read-only	IRQ value for the adapter, this information only applicable to the Broadcom adapter
INT ifBusNumber	1.3.6.1.4.1.4413.1.3.2.1.15	INTEGER	read-only	PCI Bus Number where the Adapter is situated, this information only applicable to the Broadcom adapter
INT ifDeviceNumber	1.3.6.1.4.1.4413.1.3.2.1.16	INTEGER	read-only	PCI Device Number of the adapter, this information only applicable to the Broadcom adapter
INT ifFunctionNumber	1.3.6.1.4.1.4413.1.3.2.1.17	INTEGER	read-only	PCI Function Number of the adapter, this information only applicable to the Broadcom adapter
ADR ifIpv6NetworkAddress	1.3.6.1.4.1.4413.1.3.2.1.18	InetAddressIPv6	read-only	IPv6 address of the adapter.

RFC description

Reports hardware inventory and configuration details for Broadcom NIC adapters in server systems.

Start monitoring Servers with Broadcom network interface cards (NICs) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Brcm-adapterInfo-MIB

What Is Brcm-adapterInfo-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description