FASTPATH-QOS-DIFFSERV-EXTENSIONS-MIB

All MIBs › FASTPATH-QOS-DIFFSERV-EXTENSIONS-MIB

Organization: Netgear

Last Updated: 2007-05-23

Category: Quality of Service, Vendor: Broadcom

Description: A Broadcom/Netgear FastPath vendor extension to the standard DiffServ MIB, adding objects for further QoS policy and classifier configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is FASTPATH-QOS-DIFFSERV-EXTENSIONS-MIB?

FASTPATH-QOS-DIFFSERV-EXTENSIONS-MIB is a Broadcom/Netgear FastPath proprietary MIB that extends the standard DiffServ MIB with additional multi-field classifier objects for switches running the FastPath switching stack. It exposes classifier configuration tables that match traffic on source/destination IP address and mask, protocol, and Layer 4 port ranges, supplementing what the standard DiffServ MIB alone can express. Monitoring-wise this is a configuration/software-policy MIB: an operator uses it to verify that QoS classification rules are correctly defined, which explains observed traffic prioritization or policing behavior rather than reporting hardware faults. It explicitly depends on and extends IETF's standard DIFFSERV-MIB, since its auxiliary classifier table supplements that standard's multi-field classifier model. It is deployed on managed switches built on Broadcom's FastPath software (branded variously by Netgear, Dell, and others) wherever fine-grained DiffServ-based QoS policies are needed. Engineers can download the FASTPATH-QOS-DIFFSERV-EXTENSIONS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in FASTPATH-QOS-DIFFSERV-EXTENSIONS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Broadcom FastPath-based managed Ethernet switch (e.g. Netgear, Dell PowerConnect)

Monitoring Examples

An admin auditing why traffic from a specific subnet isn't being classified as expected would walk agentDiffServAuxMfClfrTable/agentDiffServAuxMfClfrEntry, indexed by agentDiffServAuxMfClfrId, checking agentDiffServAuxMfClfrSrcAddr/agentDiffServAuxMfClfrSrcMask and agentDiffServAuxMfClfrDstAddr/agentDiffServAuxMfClfrDstMask against the intended match criteria. agentDiffServAuxMfClfrProtocol together with agentDiffServAuxMfClfrDstL4PortMin/Max and agentDiffServAuxMfClfrSrcL4PortMin/Max reveal whether the classifier is scoped to the correct application ports, such as a rule intended for a VoIP port range that was misconfigured with the wrong port bounds.

What Can Be Monitored

DiffServ classifier match criteria
source/destination IP and mask filters
protocol-based classification
Layer 4 port range filters

Imported Objects

From DIFFSERV-MIB

IfDirection
IndexInteger
IndexIntegerNextFree
diffServMeterEntry	OBJECT-TYPE

From FASTPATH-QOS-MIB

fastPathQOS

MODULE-IDENTITY

From IF-MIB

InterfaceIndex

From INET-ADDRESS-MIB

InetPortNumber

From RFC1213-MIB

DisplayString

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
StorageType
TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using agentDiffServColorAwareLevel OID:

Select a Broadcom FastPath-based Ethernet switch (multi-vendor OEM) (DiffServ multi-field classifier extensions) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type agentDiffServColorAwareLevel into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The metering conformance level of this table entry. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value is anything other than 'conform', since that indicates the condition this object reports has changed to one worth investigating. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
fastPathQOSDiffServExtensions	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6
agentDiffServMIBObjects	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1
agentDiffServClassifier	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1
NUM agentDiffServAuxMfClfrNextFree	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.1	IndexIntegerNextFree	read-only	This object contains an unused value for agentDiffServAuxMfClfrId , or a zero to indicate that none exist.
agentDiffServAuxMfClfrTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2		not-accessible	A table of Auxiliary Multi-field Classifier filter entries that a system may use to identify IP traffic.
agentDiffServAuxMfClfrEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1		not-accessible	An IP Multi-field Classifier entry describes a single filter.
NUM agentDiffServAuxMfClfrId	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.1	IndexInteger	not-accessible	An index that enumerates the Auxiliary MultiField Classifier filter entries. Managers obtain new values for row creation in this table by reading agentDiffServAuxMfClfrNextFree.
IP agentDiffServAuxMfClfrDstAddr	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.2	IpAddress	read-create	The IP address to match against the packet's destination IP address.
IP agentDiffServAuxMfClfrDstMask	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.3	IpAddress	read-create	This mask value identifies the portion of agentDiffServAuxMfClfrDstAddr that is compared against a packet. A non-contiguous mask value is permitted. A mask of 0 indicates a match of any address.
IP agentDiffServAuxMfClfrSrcAddr	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.4	IpAddress	read-create	The IP address to match against the packet's source IP address.
IP agentDiffServAuxMfClfrSrcMask	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.5	IpAddress	read-create	This mask value identifies the portion of agentDiffServAuxMfClfrSrcAddr that is compared against a packet. A non-contiguous mask value is permitted. A mask of 0 indicates a match of any address.
U32 agentDiffServAuxMfClfrProtocol	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.6	Unsigned32	read-create	The IP protocol to match against the IPv4 protocol number. A value of 255 means match all.
INE agentDiffServAuxMfClfrDstL4PortMin	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.7	InetPortNumber	read-create	The minimum value that the layer-4 destination port number in the packet must have in order to match this classifier entry.
INE agentDiffServAuxMfClfrDstL4PortMax	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.8	InetPortNumber	read-create	The maximum value that the layer-4 destination port number in the packet must have in order to match this classifier entry. This value must be equal to or greater than the value specified for this entry in agentDiffServAuxMfClfrDstL4PortMin.
INE agentDiffServAuxMfClfrSrcL4PortMin	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.9	InetPortNumber	read-create	The minimum value that the layer-4 source port number in the packet must have in order to match this classifier entry.
INE agentDiffServAuxMfClfrSrcL4PortMax	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.10	InetPortNumber	read-create	The maximum value that the layer-4 source port number in the packet must have in order to match this classifier entry. This value must be equal to or greater than the value specified for this entry in diffServMultiFieldClfrSrcL4PortMin.
COS agentDiffServAuxMfClfrCos	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.11	CosOrAny	read-create	Three-bit user priority field in the 802.1Q tag header of a tagged Ethernet frame used as a class-match parameter. For frames containing a double VLAN tag, this field is located in the first/outer tag. A value of -1 indicates that a specific COS value has not been defined and thus all COS values are considered a match.
OCT agentDiffServAuxMfClfrTos	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.12	OCTET STRING	read-create	IP TOS bits value, defined as all eight bits of the Service Type octet in the IPv4 header. There are multiple, overlapping, meanings of the TOS octet in use today: Precedence (bits 7-5): IP Precedence, values 0-7 DSCP (bits 7-2): IP DiffServ Code Point, values 0-63 TOS (bits 7-0): IP Type of Service, by bits, values 0-255 Each of these definitions can be produced using the appropriate agentDiffServAuxMfClfrTosMask mask value. These definitions are mutually-exclusive, so only one is allowed for any given classifier element.
OCT agentDiffServAuxMfClfrTosMask	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.13	OCTET STRING	read-create	IP TOS bits mask value. It identifies the portion of agentDiffServAuxMfClfrTos that is compared against a packet. A non-contiguous mask value is permitted. A mask of 0 indicates a match of any TOS value. There are multiple, overlapping meanings of the TOS octet in use today. These are represented by the following specific mask values: Precedence (bits 7-5): 224 (bit mask '11100000') DSCP (bits 7-2): 252 (bit mask '11111100') TOS (bits 7-0): 255 (bit mask '11111111') Other mask values are also permitted.
MAC agentDiffServAuxMfClfrDstMac	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.14	MacAddress	read-create	Destination MAC address.
MAC agentDiffServAuxMfClfrDstMacMask	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.15	MacAddress	read-create	Destination MAC address mask value. This mask value identifies the portion of agentDiffServAuxMfClfrDstMac that is compared against a packet. A non-contiguous mask value is permitted. A mask of 0 indicates a match of any MAC address.
MAC agentDiffServAuxMfClfrSrcMac	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.16	MacAddress	read-create	Source MAC address.
MAC agentDiffServAuxMfClfrSrcMacMask	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.17	MacAddress	read-create	Source MAC address mask value. This mask value identifies the portion of agentDiffServAuxMfClfrSrcMac that is compared against a packet. A non-contiguous mask value is permitted. A mask of 0 indicates a match of any MAC address.
VLA agentDiffServAuxMfClfrVlanId	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.18	VlanIdOrAny	read-create	VLAN ID value for the classifier. A value of -1 indicates that a specific VLAN ID value has not been defined and thus all VLAN ID values are considered a match.
STO agentDiffServAuxMfClfrStorage	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.19	StorageType	read-create	The storage type for this conceptual row.
ROW agentDiffServAuxMfClfrStatus	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.20	RowStatus	read-create	The status of this conceptual row.
COS agentDiffServAuxMfClfrCos2	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.21	CosOrAny	read-create	Three-bit user priority field in the second/inner 802.1Q tag header of a double VLAN tagged Ethernet frame used as a class-match parameter A value of -1 indicates that a specific Secondary COS value has not been defined and thus all Secondary COS values are considered a match.
ETY agentDiffServAuxMfClfrEtypeVal1	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.22	EtypeOrAny	read-create	Ethertype value to be compared in order to match this classifier entry. The allowed value for this object is 0x0600 to 0xFFFF, with a value of 0 used to indicate this object is not involved in the classifier entry.
ETY agentDiffServAuxMfClfrEtypeVal2	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.23	EtypeOrAny	read-create	A second Ethertype value to be compared in order to match this classifier entry. This value is considered in addition to the value specified by agentDiffServAuxMfClfrEtypeVal1 and serves as a second possible match value (i.e. a packet can match either EtypeVal1 or EtypeVal2). The allowed value for this object is 0x0600 to 0xFFFF, with a value of 0 used to indicate this object is not involved in the classifier entry.
U32 agentDiffServAuxMfClfrVlanIdMin	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.24	Unsigned32	read-create	The minimum value that the VLAN ID in the packet must have in order to match this classifier entry. This field is defined as the 12-bit VLAN identifier in the 802.1Q tag header of a tagged Ethernet frame. For a double VLAN tagged frame, this field is contained in the first/outer tag.
U32 agentDiffServAuxMfClfrVlanIdMax	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.25	Unsigned32	read-create	The maximum value that the VLAN ID in the packet must have in order to match this classifier entry. This field is defined as the 12-bit VLAN identifier in the 802.1Q tag header of a tagged Ethernet frame. For a double VLAN tagged frame, this field is contained in the first/outer tag. This value must be equal to or greater than the value specified for the entry in agentDiffServAuxMfClfrVlanIdMin.
U32 agentDiffServAuxMfClfrVlanId2Min	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.26	Unsigned32	read-create	The minimum value that the Secondary VLAN ID in the packet must have in order to match this classifier entry. This field is defined as the 12-bit VLAN identifier in the second/inner 802.1Q tag header of a double VLAN tagged Ethernet frame.
U32 agentDiffServAuxMfClfrVlanId2Max	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.1.2.1.27	Unsigned32	read-create	The maximum value that the Secondary VLAN ID in the packet must have in order to match this classifier entry. This field is defined as the 12-bit VLAN identifier in the second/inner 802.1Q tag header of a double VLAN tagged Ethernet frame. This value must be equal to or greater than the value specified for the entry in agentDiffServAuxMfClfrVlanId2Min.
agentDiffServAction	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2
agentDiffServCosMarkActTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.2		not-accessible	This table enumerates specific Class of Service values used for marking or remarking the priority bits in the 802.1p header. The entries of this table may be referenced by a diffServActionSpecific attribute.
agentDiffServCosMarkActEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.2.1		not-accessible	An entry in the COS mark action table that describes a single Class of Service value used for marking.
COS agentDiffServCosMarkActCos	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.2.1.1	Cos	read-only	The Class of Service value that this Action will store into the priority bits of the 802.1p header. It is quite possible that the only packets subject to this Action are already marked with this COS value.
agentDiffServIpPrecMarkActTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.4		not-accessible	This table enumerates specific IP Precedence values used for marking or remarking the Precedence field of IP packets. The entries of this table may be referenced by a diffServActionSpecific attribute.
agentDiffServIpPrecMarkActEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.4.1		not-accessible	An entry in the IP Precedence mark action table that describes a single IP Precedence value used for marking.
IPP agentDiffServIpPrecMarkActPrecedence	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.4.1.1	IpPrecedence	read-only	The IP Precedence that this Action will store into the Precedence field of the IP packet. It is quite possible that the only packets subject to this Action are already marked with this IP Precedence. Note also that Differentiated Services processing may result in a packet being marked on both ingress to a network and on egress from it, and that ingress and egress can occur in the same router.
agentDiffServCos2MarkActTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.5		not-accessible	This table enumerates specific Secondary Class of Service values used for marking or remarking the priority bits in the second/inner 802.1Q tag header of a double VLAN tagged Ethernet packet. The entries of this table may be referenced by a diffServActionSpecific attribute.
agentDiffServCos2MarkActEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.5.1		not-accessible	An entry in the Secondary COS mark action table that describes a single Class of Service value used for marking.
COS agentDiffServCos2MarkActCos	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.5.1.1	Cos	read-only	The Secondary Class of Service value that this Action will store into the priority bits of the second/inner 802.1p tag header. It is quite possible that the only packets subject to this Action are already marked with this COS value.
NUM agentDiffServAssignQueueNextFree	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.6	IndexIntegerNextFree	read-only	This object contains an unused value for agentDiffServAssignIndex, or a zero to indicate that none exist.
agentDiffServAssignQueueTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.7		not-accessible	A table used for assigning a stream of Differentiated Services traffic to a specific quality of service (QoS) queue. The traffic stream is identified by the upstream Functional Data Path Element(s), i.e. by the object(s) that point to each entry in this table. This may include all traffic on an interface or just a portion thereof.
agentDiffServAssignQueueEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.7.1		not-accessible	An entry in the assign queue table describes a specific (egress) QoS queue identifier for a traffic stream.
NUM agentDiffServAssignQueueIndex	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.7.1.1	IndexInteger	not-accessible	An index that enumerates the Assign Queue entries. Managers obtain new values for row creation in this table by reading agentDiffServAssignQueueNextFree.
U32 agentDiffServAssignQueueQnum	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.7.1.2	Unsigned32	read-create	The queue identifier value. This value indicates the QoS queue number to which the traffic stream for this data path is directed for egress from the device.
STO agentDiffServAssignQueueStorage	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.7.1.3	StorageType	read-create	The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
ROW agentDiffServAssignQueueStatus	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.7.1.4	RowStatus	read-create	The status of this conceptual row. All writable objects in this row may be modified at any time. Setting this variable to 'destroy' when the MIB contains one or more RowPointers pointing to it results in destruction being delayed until the row is no longer used.
NUM agentDiffServRedirectNextFree	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.8	IndexIntegerNextFree	read-only	This object contains an unused value for agentDiffServRedirectId, or a zero to indicate that none exist.
agentDiffServRedirectTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.9		not-accessible	A table used for redirecting a stream of Differentiated Services traffic to a specific egress interface, bypassing any normal device forwarding decision. The traffic stream is identified by the upstream Functional Data Path Element(s), i.e. by the object(s) that point to each entry in this table. This may include all traffic on an interface or just a portion thereof.
agentDiffServRedirectEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.9.1		not-accessible	An entry in the redirect table describes a specific external interface number used as the egress point of a traffic stream.
NUM agentDiffServRedirectId	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.9.1.1	IndexInteger	not-accessible	An index that enumerates the Redirect entries. Managers obtain new values for row creation in this table by reading agentDiffServRedirectNextFree.
NUM agentDiffServRedirectIntf	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.9.1.2	InterfaceIndex	read-create	The external interface number identifier value. This value indicates the egress interface to which the traffic stream for this data path is directed. Normal traffic forwarding decisions are bypassed.
STO agentDiffServRedirectStorage	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.9.1.3	StorageType	read-create	The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
ROW agentDiffServRedirectStatus	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.9.1.4	RowStatus	read-create	The status of this conceptual row. All writable objects in this row may be modified at any time. Setting this variable to 'destroy' when the MIB contains one or more RowPointers pointing to it results in destruction being delayed until the row is no longer used.
NUM agentDiffServMirrorNextFree	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.10	IndexIntegerNextFree	read-only	This object contains an unused value for agentDiffServMirrorId, or a zero to indicate that none exist.
agentDiffServMirrorTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.11		not-accessible	A table used for mirroring a stream of Differentiated Services traffic to a specific egress interface, in addition to any normal device forwarding decision. The traffic stream is identified by the upstream Functional Data Path Element(s), i.e. by the object(s) that point to each entry in this table. This may include all traffic on an interface or just a portion thereof.
agentDiffServMirrorEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.11.1		not-accessible	An entry in the mirror table describes a specific external interface number used as the egress point of a copied traffic stream.
NUM agentDiffServMirrorId	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.11.1.1	IndexInteger	not-accessible	An index that enumerates the Mirror entries. Managers obtain new values for row creation in this table by reading agentDiffServMirrorNextFree.
NUM agentDiffServMirrorIntf	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.11.1.2	InterfaceIndex	read-create	The external interface number identifier value. This value indicates the egress interface to which the traffic stream for this data path is copied. Normal traffic forwarding decisions are still performed on the traffic stream.
STO agentDiffServMirrorStorage	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.11.1.3	StorageType	read-create	The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
ROW agentDiffServMirrorStatus	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.2.11.1.4	RowStatus	read-create	The status of this conceptual row. All writable objects in this row may be modified at any time. Setting this variable to 'destroy' when the MIB contains one or more RowPointers pointing to it results in destruction being delayed until the row is no longer used.
agentDiffServMeter	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.3
agentDiffServColorAwareTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.3.1		not-accessible	A table used for augmenting the Differentiated Services meter information with information describing the packet coloration characteristics for a color-aware mode of policing. The diffServMeterId is used as the index to this table, which logically extends the Meter table row with the columnar objects defined in this Color Aware table row.
agentDiffServColorAwareEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.3.1.1		not-accessible	An entry in the color aware table describes a single color conformance level of a meter.
INT agentDiffServColorAwareLevelEx	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.3.1.1.1	INTEGER	read-create	The metering conformance level of this table entry. A policing meter represents either a conforming or an exceeding level of traffic in the traffic stream for this data path. The color characteristics used by the meter are relevant to this conformance level. This object is set to unused(3) when the meter is not being used for policing.
INT agentDiffServColorAwareMode	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.3.1.1.2	INTEGER	read-create	The color mode indicator for the meter. When set to blind(1), metering is performed in a color-blind manner such that any packet markings are ignored by the meter. The other values listed for this object indicate the packet field used for determining its pre-existing color marking. In color-aware mode, the current color of a packet (e.g. green, yellow, red) influences the metering outcome. The object value awareunused(6) is special in that it denotes that the specific field attributes are not specified for the meter even though a color aware scheme is in use for policing. This object always returns blind(1) when the agentDiffServColorAwareLevel is set to unused(3).
U32 agentDiffServColorAwareValue	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.1.3.1.1.3	Unsigned32	read-create	The value of the color aware table entry. This value is used to compare the field indicated in agentDiffServColorAwareMode against packets in a traffic stream along the data path supplying the meter for a given conformance level. This object always returns 0 when the agentDiffServColorAwareMode is set to blind(1) or awareunused(6).
agentDiffServMIBAdmin	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.2
agentDiffServTBMeters	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.2.1
agentDiffServTBParamSimpleTokenBucketAware	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.3.6.2.1.1			Two Parameter Token Bucket Meter as described in the Informal Differentiated Services Model section 5.2.3, but using a color-aware mode of operation.

RFC description

Broadcom/Netgear FastPath proprietary extensions to the standard DiffServ MIB, providing additional QoS policy and classifier configuration.

Start monitoring Broadcom FastPath-based Ethernet switch (multi-vendor OEM) (DiffServ multi-field classifier extensions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download FASTPATH-QOS-DIFFSERV-EXTENSIONS-MIB