BIANCA-BRICK-SIF-MIB

All MIBs › BIANCA-BRICK-SIF-MIB

Category: Network Interfaces, Vendor: bintec

Description: Manages synchronous interface (SIF) configuration and status on bintec elmeg BIANCA/BRICK routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is BIANCA-BRICK-SIF-MIB?

BIANCA-BRICK-SIF-MIB is a proprietary bintec elmeg (BIANCA/BRICK) MIB for the router's synchronous serial interfaces (SIF), used for leased-line or other synchronous WAN connections. It is expected to expose per-interface configuration such as clocking and encapsulation, along with operational status and error counters for these serial links. Its monitoring value is hardware interface status: physical link up/down state, signal/clocking status, and frame/error counters on synchronous WAN links, since serial hardware issues like cabling or clocking mismatches are a common source of WAN outages. It likely parallels the standard IF-MIB's ifTable concepts for these serial interfaces. It is used on bintec elmeg BIANCA/BRICK routers connected via leased-line or other synchronous serial WAN circuits in branch-office/enterprise WAN deployments. Engineers can download the BIANCA-BRICK-SIF-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in BIANCA-BRICK-SIF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

bintec elmeg BIANCA/BRICK router

Monitoring Examples

No sample objects were extracted for this module in the available data. Conceptually, an admin would poll each synchronous interface's link/operational state and error counters; a link flapping between up and down, or a rising frame/CRC error count, reveals a physical-layer problem such as a bad cable, clocking mismatch, or carrier-side circuit fault on the serial WAN connection.

What Can Be Monitored

synchronous interface link state
clocking/signal status
frame/CRC error counters
interface encapsulation configuration

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
enterprises

From RFC1158-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
bibo	1.3.6.1.4.1.272.4
biboip	1.3.6.1.4.1.272.4.5
bintec	1.3.6.1.4.1.272
ipSif	1.3.6.1.4.1.272.4.5.37
INT ipSifAdminStatus	1.3.6.1.4.1.272.4.5.37.1	INTEGER	read-write	Enable or disable Stateful Inspection Firewall.
INT ipSifAliasAction	1.3.6.1.4.1.272.4.5.30.1.5	INTEGER	read-write	The Rule for the Filter
IP ipSifAliasAddressAddress	1.3.6.1.4.1.272.4.5.28.1.3	IpAddress	read-write	The ip-address for the Alias
STR ipSifAliasAddressAlias	1.3.6.1.4.1.272.4.5.28.1.2	DisplayString	read-write	Alias Name for the Address Entry
ipSifAliasAddressEntry	1.3.6.1.4.1.272.4.5.28.1		not-accessible	Contents a Stateful inspection Firewall description for a alias Name
INT ipSifAliasAddressGroup	1.3.6.1.4.1.272.4.5.28.1.8	INTEGER	read-write	For values greater than zero this entry determines the IP address group this entry belongs to, see also ipSifAliasAddressGroupId
STR ipSifAliasAddressGroupAlias	1.3.6.1.4.1.272.4.5.47.1.2	DisplayString	read-write	Alias name for the address group entry
ipSifAliasAddressGroupEntry	1.3.6.1.4.1.272.4.5.47.1		not-accessible	Defines IP address or interface group alias
INT ipSifAliasAddressGroupId	1.3.6.1.4.1.272.4.5.47.1.1	INTEGER	read-write	The unique address group entry ID
INT ipSifAliasAddressGroupIndex	1.3.6.1.4.1.272.4.5.47.1.3	INTEGER	read-only	The index for the address group entry to be referred by an ipSifAlias entry
INT ipSifAliasAddressGroupMode	1.3.6.1.4.1.272.4.5.47.1.4	INTEGER	read-write	Specifies wether this entry defines an interface or address group
ipSifAliasAddressGroupTable	1.3.6.1.4.1.272.4.5.47		not-accessible	Defines IP address or interface group alias
INT ipSifAliasAddressIndex	1.3.6.1.4.1.272.4.5.28.1.1	INTEGER	read-only	The Index for the address alias
INT ipSifAliasAddressInterface	1.3.6.1.4.1.272.4.5.28.1.5	INTEGER	read-write	The interface index for the alias
IP ipSifAliasAddressMask	1.3.6.1.4.1.272.4.5.28.1.4	IpAddress	read-write	The ip Mask for the Alias
INT ipSifAliasAddressMode	1.3.6.1.4.1.272.4.5.28.1.6	INTEGER	read-write	Address or Interface Mode
INT ipSifAliasAddressRange	1.3.6.1.4.1.272.4.5.28.1.7	INTEGER	read-write	The ip Range for the Alias
ipSifAliasAddressTable	1.3.6.1.4.1.272.4.5.28		not-accessible	Contains a alias Address Entry Index,Ip,Mask,Interface
INT ipSifAliasClassId	1.3.6.1.4.1.272.4.5.30.1.8	INTEGER	read-write	Internal ID for SIF policy to QoS policy mapping
INT ipSifAliasDestination	1.3.6.1.4.1.272.4.5.30.1.3	INTEGER	read-write	The alias Destination Index for the Entry
ipSifAliasEntry	1.3.6.1.4.1.272.4.5.30.1		not-accessible
INT ipSifAliasOrder	1.3.6.1.4.1.272.4.5.30.1.1	INTEGER	read-write	The Order for the Stateful Inspection Entry rule
INT ipSifAliasPriority	1.3.6.1.4.1.272.4.5.30.1.7	INTEGER	read-write	Defines the QoS priority of this policy
INT ipSifAliasService	1.3.6.1.4.1.272.4.5.30.1.4	INTEGER	read-write	The alias Protocol/service Index for Entry
STR ipSifAliasServiceAlias	1.3.6.1.4.1.272.4.5.29.1.2	DisplayString	read-write	Alias Name for the Service Entry
ipSifAliasServiceEntry	1.3.6.1.4.1.272.4.5.29.1		not-accessible	Contains a alias Service Entry Protocol,Port,Range
INT ipSifAliasServiceGroup	1.3.6.1.4.1.272.4.5.29.1.7	INTEGER	read-write	For values greater than zero this entry determines the IP service group this entry belongs to, see also ipSifAliasServiceGroupId
STR ipSifAliasServiceGroupAlias	1.3.6.1.4.1.272.4.5.48.1.2	DisplayString	read-write	Alias name for the IP service group entry
ipSifAliasServiceGroupEntry	1.3.6.1.4.1.272.4.5.48.1		not-accessible	Defines IP service group alias
INT ipSifAliasServiceGroupId	1.3.6.1.4.1.272.4.5.48.1.1	INTEGER	read-write	The unique IP service group entry ID
INT ipSifAliasServiceGroupIndex	1.3.6.1.4.1.272.4.5.48.1.3	INTEGER	read-only	The index for the Ip service group entry to be referred by an ipSifAlias entry
INT ipSifAliasServiceGroupMode	1.3.6.1.4.1.272.4.5.48.1.4	INTEGER	read-write	Specifies wether this entry defines an IP service group or should be deleted
ipSifAliasServiceGroupTable	1.3.6.1.4.1.272.4.5.48		not-accessible	Defines IP service group alias
INT ipSifAliasServiceIcmpCode	1.3.6.1.4.1.272.4.5.29.1.11	INTEGER	read-write	The ICMP Code for the Service Alias.
INT ipSifAliasServiceIcmpType	1.3.6.1.4.1.272.4.5.29.1.10	INTEGER	read-write	The ICMP Type for the Service Alias.
INT ipSifAliasServiceIndex	1.3.6.1.4.1.272.4.5.29.1.1	INTEGER	read-only	The Index for the address alias
INT ipSifAliasServicePort	1.3.6.1.4.1.272.4.5.29.1.4	INTEGER	read-write	The Port for the Service Alias.
INT ipSifAliasServiceProtocol	1.3.6.1.4.1.272.4.5.29.1.3	INTEGER	read-write	The protocol for the Service alias
INT ipSifAliasServiceRange	1.3.6.1.4.1.272.4.5.29.1.5	INTEGER	read-write	The Port Range for the Service Alias.
INT ipSifAliasServiceSourcePort	1.3.6.1.4.1.272.4.5.29.1.8	INTEGER	read-write	The Source Port for the Service Alias.
INT ipSifAliasServiceSourceRange	1.3.6.1.4.1.272.4.5.29.1.9	INTEGER	read-write	The Source Port Range for the Service Alias.
ipSifAliasServiceTable	1.3.6.1.4.1.272.4.5.29		not-accessible	Contains a alias Service Entry Protocol,Port,Range
INT ipSifAliasServiceType	1.3.6.1.4.1.272.4.5.29.1.6	INTEGER	read-only	Specifies wether created by the IP/SIF subsystem itself or created/modified by the administrator.
INT ipSifAliasSource	1.3.6.1.4.1.272.4.5.30.1.2	INTEGER	read-write	The alias Source Index for the Entry
INT ipSifAliasStatus	1.3.6.1.4.1.272.4.5.30.1.6	INTEGER	read-write	Defines the administrative status of this policy
ipSifAliasTable	1.3.6.1.4.1.272.4.5.30		not-accessible	Contains a Stateful Inspection Firewall (SIF) policy.
INT ipSifDefaultTimeout	1.3.6.1.4.1.272.4.5.37.8	INTEGER	read-write	Timeout on all other ip Sessions
INT ipSifExpectClassId	1.3.6.1.4.1.272.4.5.35.1.8	INTEGER	read-only	Internal ID for mapping SIF-policy to QoS-policy. Default-value of 0 means NOT SPECIFIED.
IP ipSifExpectDestination	1.3.6.1.4.1.272.4.5.35.1.3	IpAddress	read-only	The destination-IP-address for the expected session. A value of 0 means ANY destination-address.
INT ipSifExpectDestPort	1.3.6.1.4.1.272.4.5.35.1.6	INTEGER	read-only	The destination-port-number of the expected session. A value of 0 means ANY destination-port-number.
ipSifExpectEntry	1.3.6.1.4.1.272.4.5.35.1		not-accessible
INT ipSifExpectIfIndex	1.3.6.1.4.1.272.4.5.35.1.9	INTEGER	read-only	Interface-index for which the session is expected. A value of 0 means ANY interface-index.
INT ipSifExpectIndex	1.3.6.1.4.1.272.4.5.35.1.1	INTEGER	read-only	This field is used for SIF-internal signalling and stores the index for the expected session for later matching.
INT ipSifExpectPriority	1.3.6.1.4.1.272.4.5.35.1.7	INTEGER	read-only	Defines the QoS-priority/policy to be used for the expected SIF-session.
INT ipSifExpectProtocol	1.3.6.1.4.1.272.4.5.35.1.4	INTEGER	read-write	The protocol of the expected session.
IP ipSifExpectSource	1.3.6.1.4.1.272.4.5.35.1.2	IpAddress	read-only	The source-IP-address for the expected session. A value of 0 means ANY source-address.
INT ipSifExpectSourcePort	1.3.6.1.4.1.272.4.5.35.1.5	INTEGER	read-only	The source-port-number of the expected session. A value of 0 means ANY source-port-number.
ipSifExpectTable	1.3.6.1.4.1.272.4.5.35		not-accessible	Contains expected Sessions with Source Destination
INT ipSifInterfaceAliasAutoCreate	1.3.6.1.4.1.272.4.5.37.16	INTEGER	read-write	Enable or disable automatic creation of interface aliases (see ipSifAliasAddressTable) due to created MPR interfaces visible in ifTable.
INT ipSifInterfaceFilter	1.3.6.1.4.1.272.4.5.37.3	INTEGER	read-write	Enable or disable filtering on same Interface packets
INT ipSifLocalFilter	1.3.6.1.4.1.272.4.5.37.2	INTEGER	read-write	Enable or disable filtering on local requests
INT ipSifMaxRejectEntries	1.3.6.1.4.1.272.4.5.37.14	INTEGER	read-write	Maximum number of ipSifRejectTable entries
INT ipSifMaxRejectTtl	1.3.6.1.4.1.272.4.5.37.15	INTEGER	read-write	Maximum time to live of the ipSifRejectTable entries in seconds
INT ipSifMaxSessions	1.3.6.1.4.1.272.4.5.37.9	INTEGER	read-write	Maximum number of monitored sessions
INT ipSifPolicyChkAdminStatus	1.3.6.1.4.1.272.4.5.49.1.11	INTEGER	read-write	Determines wether the ipSifAdminStatus should be considered for the policy (check (1)) or not (ingnore (2)).
INT ipSifPolicyChkCurrOperStatus	1.3.6.1.4.1.272.4.5.49.1.13	INTEGER	read-only	The current SIF operational status.
INT ipSifPolicyChkDestIfIndex	1.3.6.1.4.1.272.4.5.49.1.2	INTEGER	read-write	The destination interface index, for example '1' addresses the 'local' interface whereas '0' means 'don't check.'
IP ipSifPolicyChkDestination	1.3.6.1.4.1.272.4.5.49.1.4	IpAddress	read-write	The destination IP address, 0.0.0.0 means 'don't check'.
INT ipSifPolicyChkDestPort	1.3.6.1.4.1.272.4.5.49.1.6	INTEGER	read-write	The destination port number (UDP/TCP service) to checked, '0' means 'don't check.
ipSifPolicyChkEntry	1.3.6.1.4.1.272.4.5.49.1		not-accessible
INT ipSifPolicyChkOperStatus	1.3.6.1.4.1.272.4.5.49.1.12	INTEGER	read-write	Determines wether the SIF operational status should be considered for the policy (check (1)) or not (ingnore (2)).
INT ipSifPolicyChkProtocol	1.3.6.1.4.1.272.4.5.49.1.5	INTEGER	read-write	The IP protocol number to checked, '0' means 'don't check.
INT ipSifPolicyChkResult	1.3.6.1.4.1.272.4.5.49.1.9	INTEGER	read-only	Returns the result depending on: - ipSifPolicyChkRule - administrative status (ipSifAdminStatus) - operational status of the SIF engine
INT ipSifPolicyChkRule	1.3.6.1.4.1.272.4.5.49.1.7	INTEGER	read-only	Returns the associated policy, depending on: - ipSifAliasAction - ipSifAliasOrder - ipSifAliasStatus
INT ipSifPolicyChkRuleOrder	1.3.6.1.4.1.272.4.5.49.1.8	INTEGER	read-only	Returns the associated policy order (see ipSifAliasOrder).
IP ipSifPolicyChkSource	1.3.6.1.4.1.272.4.5.49.1.3	IpAddress	read-write	The source IP address, 0.0.0.0 means 'don't check'.
INT ipSifPolicyChkSourceIfIndex	1.3.6.1.4.1.272.4.5.49.1.1	INTEGER	read-write	The source interface index, for example '1' addresses the 'local' interface whereas '0' means 'don't check.
INT ipSifPolicyChkState	1.3.6.1.4.1.272.4.5.49.1.10	INTEGER	read-write	Displays the current status of the policy check, when setting to trigger(2) a new check will be initiated.
ipSifPolicyChkTable	1.3.6.1.4.1.272.4.5.49		not-accessible	MIB interface in order to check the configured SIF polices: - for debugging purposes - for test applications - for configuration frontends NOTE: it's a stateless check, not based on a real IP session context
INT ipSifPPTPTimeout	1.3.6.1.4.1.272.4.5.37.7	INTEGER	read-write	Timeout on inactive PPTP Session
IP ipSifRejectDestination	1.3.6.1.4.1.272.4.5.31.1.3	IpAddress	read-only	The Reject Destination Index for the Entry
ipSifRejectEntry	1.3.6.1.4.1.272.4.5.31.1		not-accessible
INT ipSifRejectIndex	1.3.6.1.4.1.272.4.5.31.1.1	INTEGER	read-only	The Index for the Reject Entry
INT ipSifRejectPortHigh	1.3.6.1.4.1.272.4.5.31.1.8	INTEGER	read-only	The highest port rejected
INT ipSifRejectPortLo	1.3.6.1.4.1.272.4.5.31.1.7	INTEGER	read-only	The lowest Port rejected
INT ipSifRejectProtocol	1.3.6.1.4.1.272.4.5.31.1.6	INTEGER	read-only	The protocol of the rejected Packet
INT ipSifRejectRejects	1.3.6.1.4.1.272.4.5.31.1.4	INTEGER	read-only	Count of rejected frames
INT ipSifRejectSilence	1.3.6.1.4.1.272.4.5.31.1.5	INTEGER	read-only	Last reject in seconds
IP ipSifRejectSource	1.3.6.1.4.1.272.4.5.31.1.2	IpAddress	read-only	The Reject Source for the Entry
ipSifRejectTable	1.3.6.1.4.1.272.4.5.31		not-accessible	Contains actually rejected Frames with Source Destination
ipSifStat	1.3.6.1.4.1.272.4.5.46
CTR ipSifStatCurrExpectedSessions	1.3.6.1.4.1.272.4.5.46.5	Counter	read-only	Current number of created expected sessions
CTR ipSifStatCurrOtherSessions	1.3.6.1.4.1.272.4.5.46.4	Counter	read-only	Current number of monitored non-TCP/UDP sessions
CTR ipSifStatCurrSessions	1.3.6.1.4.1.272.4.5.46.1	Counter	read-only	Current number of all monitored sessions
CTR ipSifStatCurrTcpSessions	1.3.6.1.4.1.272.4.5.46.3	Counter	read-only	Current number of monitored TCP sessions
CTR ipSifStatCurrUdpSessions	1.3.6.1.4.1.272.4.5.46.2	Counter	read-only	Current number of monitored UDP sessions
CTR ipSifStatTotalExpectedSessions	1.3.6.1.4.1.272.4.5.46.9	Counter	read-only	Total number of monitored non-TCP/UDP sessions
CTR ipSifStatTotalOtherSessions	1.3.6.1.4.1.272.4.5.46.8	Counter	read-only	Total number of monitored non-TCP/UDP sessions
CTR ipSifStatTotalTcpSessions	1.3.6.1.4.1.272.4.5.46.7	Counter	read-only	Total number of monitored TCP sessions
CTR ipSifStatTotalUdpSessions	1.3.6.1.4.1.272.4.5.46.6	Counter	read-only	Total number of monitored UDP sessions
INT ipSifSysloglevel	1.3.6.1.4.1.272.4.5.37.4	INTEGER	read-write	Levels for less or more Informations in the Syslog, verbose : display all Sif Activity deny : display only rejects, ignore accept : display only accpts none : disable Syslogs
INT ipSifTcpTimeout	1.3.6.1.4.1.272.4.5.37.6	INTEGER	read-write	Timeout on inactive TCP Session
INT ipSifUdpTimeout	1.3.6.1.4.1.272.4.5.37.5	INTEGER	read-write	Timeout on inactive UDP Session

RFC description

Manages stateful inspection firewall configuration and IP alias addresses.

Start monitoring bintec BIANCA/BRICK ISDN/VPN routers (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download BIANCA-BRICK-SIF-MIB

What Is BIANCA-BRICK-SIF-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description