AXD301-ILMI-MIB

All MIBs › AXD301-ILMI-MIB

Category: ATM, Vendor: ACC/Ericsson

Description: Manages ILMI (Integrated Local Management Interface) ATM signaling on the Ericsson AXD301 ATM switch.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AXD301-ILMI-MIB?

AXD301-ILMI-MIB manages ILMI (Integrated Local Management Interface) ATM signaling on the Ericsson AXD301 ATM switch, a carrier-grade ATM switching platform. Its data categories combine standard system-identity objects (sysDescr, sysObjectID, sysUpTime, sysContact, sysName, sysLocation, sysServices) with ATM Forum-defined per-port signaling objects (atmfPortTable) describing ATM port transmission types. It supports basic hardware/software status monitoring through the standard system group — sysUpTime for device uptime and sysDescr/sysObjectID for identifying the switch's software/hardware identity — while the ATM Forum objects report the operational transmission characteristics of individual ATM ports. It explicitly depends on the ATM Forum's ILMI/UNI MIB definitions (imported atmForum, atmForumAdmin, atmfTransmissionTypes) as well as the standard SNMPv2 System group (MIB-II). It is deployed in carrier and enterprise ATM backbone networks, where AXD301-ILMI-MIB SNMP monitoring supports the Ericsson AXD301 switch for ATM-based transport.

IPNetwork Monitor allows you to monitor SNMP objects defined in AXD301-ILMI-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ericsson AXD301 ATM switch

Monitoring Examples

An admin would poll sysUpTime to confirm the AXD301 switch has not unexpectedly rebooted, and sysDescr/sysObjectID to verify its software/hardware identity during an inventory audit. atmfPortTable/atmfPortEntry, keyed by atmfPortIndex, reports each ATM port's transmission type from atmfTransmissionTypes; a port reporting an unexpected or non-operational transmission type would reveal a physical-layer or signaling mismatch on that ATM interface.

What Can Be Monitored

system uptime
system identity (sysDescr/sysObjectID)
ATM port transmission type
ATM port index/status

Imported Objects

From ATM-TC-MIB

AtmServiceCategory

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString
mib-2

From SNMPv2-TC

TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
atmf4B5B	1.3.6.1.4.1.353.1.2.4
atmf8B10B	1.3.6.1.4.1.353.1.2.5
ADR atmfAddressAtmAddress	1.3.6.1.4.1.353.2.6.1.1.2	AtmAddress	not-accessible	The ATM address which is in effect on the user side of the ATM UNI port.
atmfAddressEntry	1.3.6.1.4.1.353.2.6.1.1		not-accessible	Information about a single ATM-layer address in effect on the user-side IME. Note that the index variable atmAddressAtmAddress is a variable-length string, and as such the rule for variable-length strings in section 4.1.6 of RFC 1212 applies.
atmfAddressGroup	1.3.6.1.4.1.353.2.6
INT atmfAddressOrgScope	1.3.6.1.4.1.353.2.6.1.1.4	INTEGER	read-write	This object indicates the organizational scope for the referenced address. The information of the referenced address shall not be distributed outside the indicated scope. If the user-side IME does not specify a value for the atmfAddressOrgScope object, the network shall set the value of this object to localNetwork(1), if the registered address is an ATM group address, or to global(15), if the registered address is an individual address. Refer to Annex 6.0 of ATM Forum UNI Signalling 4.0 for guidelines regarding the use of organizational scopes. This organization hierarchy may be mapped to ATM network's routing hierarchy such as PNNI's routing level and the mapping shall be configurable in nodes. Use of this object in a public network is for further study. The default values for organizational scope are localNetwork(1) for ATM group addresses, and global(15) for individual addresses.
INT atmfAddressPort	1.3.6.1.4.1.353.2.6.1.1.1	INTEGER	not-accessible	A unique value which identifies the UNI port for which the ATM address is in effect. The value of 0 has the special meaning of identifying the local UNI.
atmfAddressRegistrationAdminEntry	1.3.6.1.4.1.353.2.11.1.1		not-accessible	An entry in the table, containing Address Registration administrative information for the ATM Interface.
atmfAddressRegistrationAdminGroup	1.3.6.1.4.1.353.2.11
INT atmfAddressRegistrationAdminIndex	1.3.6.1.4.1.353.2.11.1.1.1	INTEGER	read-only	The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received.
INT atmfAddressRegistrationAdminStatus	1.3.6.1.4.1.353.2.11.1.1.2	INTEGER	read-only	An indication of whether or not Address Registration is supported on this ATM Interface. Supported(1) indicates that this ATM Interface supports address registration. Unsupported(2) indicates that this ATM Interface does not support address registration.
atmfAddressRegistrationAdminTable	1.3.6.1.4.1.353.2.11.1		not-accessible	A table of Address Registration administrative information for the ATM Interface.
INT atmfAddressStatus	1.3.6.1.4.1.353.2.6.1.1.3	INTEGER	read-write	An indication of the validity of the ATM address at the user side of the UNI port. To configure a new address in this table, the user-side IME must set the appropriate instance of this object to the value valid(1). To delete an existing address in this table, the user-side IME must set the appropriate instance of this object to the value invalid(2). If circumstances occur on the network-side IME which cause an address to become invalid, the network-side IME modifies the value of the appropriate instance of this object to invalid(2). Whenever the value of this object for a particular address becomes invalid(2), the conceptual row for that address may be removed from the table at any time, either immediately or subsequently.
atmfAddressTable	1.3.6.1.4.1.353.2.6.1		not-accessible	A table implemented by the network-side IME, containing the ATM-layer addresses in effect on the user side of the UNI.
INT atmfAtmLayerConfiguredVCCs	1.3.6.1.4.1.353.2.2.1.1.5	INTEGER	read-only	The number of permanent VCCs configured for use on this ATM Interface.
INT atmfAtmLayerConfiguredVPCs	1.3.6.1.4.1.353.2.2.1.1.4	INTEGER	read-only	The number of permanent VPCs configured for use on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections used by PNNI), the maximum number of VPCs is set to zero.
INT atmfAtmLayerDeviceType	1.3.6.1.4.1.353.2.2.1.1.10	INTEGER	read-only	This object determines the type of the ATM device. This object is used in automatic ATM Interface-Type determination procedure such that a correct operational ATM Interface-type can be determined. An ATM End System shall take the value of user(1), and an ATM network node shall take the value of node(2).
atmfAtmLayerEntry	1.3.6.1.4.1.353.2.2.1.1		not-accessible	An entry in the table, containing information about the ATM layer of an ATM Interface.
atmfAtmLayerGroup	1.3.6.1.4.1.353.2.2
INT atmfAtmLayerIlmiVersion	1.3.6.1.4.1.353.2.2.1.1.11	INTEGER	read-only	An indication of the latest version of the ATM Forum ILMI Specification that is supported on this ATM Interface. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. If this object is not present, a version of the ILMI earlier than 4.0 is supported.
INT atmfAtmLayerIndex	1.3.6.1.4.1.353.2.2.1.1.1	INTEGER	read-only	The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received.
INT atmfAtmLayerMaxSvccVpi	1.3.6.1.4.1.353.2.2.1.1.14	INTEGER	read-only	The maximum VPI that the signalling stack on the ATM interface is configured to support for allocation to switched virtual channel connections.
INT atmfAtmLayerMaxSvpcVpi	1.3.6.1.4.1.353.2.2.1.1.13	INTEGER	read-only	The maximum VPI that the signalling stack on the ATM interface is configured to support for allocation to switched virtual path connections.
INT atmfAtmLayerMaxVCCs	1.3.6.1.4.1.353.2.2.1.1.3	INTEGER	read-only	The maximum number of switched and permanent VCCs supported on this ATM Interface.
INT atmfAtmLayerMaxVciBits	1.3.6.1.4.1.353.2.2.1.1.7	INTEGER	read-only	The maximum number of active VCI bits on this ATM Interface.
INT atmfAtmLayerMaxVPCs	1.3.6.1.4.1.353.2.2.1.1.2	INTEGER	read-only	The maximum number of switched and permanent VPCs supported on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections), the maximum number of VPCs PNNI may communicate over is set to zero.
INT atmfAtmLayerMaxVpiBits	1.3.6.1.4.1.353.2.2.1.1.6	INTEGER	read-only	The maximum number of active VPI bits on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections used by PNNI), this value has no meaning and is set to zero.
INT atmfAtmLayerMinSvccVci	1.3.6.1.4.1.353.2.2.1.1.15	INTEGER	read-only	This is the minimum VCI value that the signalling stack is configured to support for allocation to switched virtual channel connections. The same value applies to all SVCC VPI values for which the signalling stack is configured.
INT atmfAtmLayerNniSigVersion	1.3.6.1.4.1.353.2.2.1.1.12	INTEGER	read-only	An indication of the latest version of the ATM Forum PNNI Signalling Specification that is supported on this ATM Interface. Note that the PNNI routing version is not determined through ILMI. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed.
atmfAtmLayerTable	1.3.6.1.4.1.353.2.2.1		not-accessible	A table of ATM layer status and parameter information for the ATM Interface.
INT atmfAtmLayerUniType	1.3.6.1.4.1.353.2.2.1.1.8	INTEGER	read-only	The type of the ATM device, either public or private.
INT atmfAtmLayerUniVersion	1.3.6.1.4.1.353.2.2.1.1.9	INTEGER	read-only	An indication of the latest version of the ATM Forum UNI Signalling Specification that is supported on this ATM Interface. If this value is not present, a version of the UNI earlier than 3.1 is supported. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed.
atmfAtmStatsGroup	1.3.6.1.4.1.353.2.3
atmfClpNoTaggingMcr	1.3.6.1.4.1.353.1.4.9
atmfClpNoTaggingNoScr	1.3.6.1.4.1.353.1.4.4
atmfClpNoTaggingScr	1.3.6.1.4.1.353.1.4.7
atmfClpTaggingNoScr	1.3.6.1.4.1.353.1.4.5
atmfClpTaggingScr	1.3.6.1.4.1.353.1.4.8
atmfDs3	1.3.6.1.4.1.353.1.2.3
atmfE1	1.3.6.1.4.1.353.1.2.9
atmfE3	1.3.6.1.4.1.353.1.2.7
atmfMediaCoaxCable	1.3.6.1.4.1.353.1.3.2
atmfMediaMultiMode	1.3.6.1.4.1.353.1.3.4
atmfMediaSingleMode	1.3.6.1.4.1.353.1.3.3
atmfMediaStp	1.3.6.1.4.1.353.1.3.5
atmfMediaTypes	1.3.6.1.4.1.353.1.3
atmfMediaUnknownType	1.3.6.1.4.1.353.1.3.1
atmfMediaUtp	1.3.6.1.4.1.353.1.3.6
IP atmfMyIpNmAddress	1.3.6.1.4.1.353.2.1.2	IpAddress	read-only	An IP Address to which a Network Management Station can send Network Management protocol messages, e.g. SNMP messages to UDP port 161, in order to access network management information concerning the operation of the ATM device local to this IME. If this object is supported, but the Network Management Agent has not been configured with an IP Address, the IME should return 0.0.0.0.
ADR atmfMyOsiNmNsapAddress	1.3.6.1.4.1.353.2.1.3	ClnpAddress	read-only	An NSAP Address to which a Network Management Station can send Network Management protocol messages in order to access network management information concerning the operation of the ATM device local to this IME. If this object is supported, but the Network Management Agent has not been configured with an NSAP Address, the IME should return 0.0.0.0
OCT atmfMySystemIdentifier	1.3.6.1.4.1.353.2.1.4	OCTET STRING	read-only	A 48 bit identifier, taken from the IEEE universally administered MAC address space, which uniquely identifies the ATM device local to this IME.
atmfNetPrefixEntry	1.3.6.1.4.1.353.2.7.1.1		not-accessible	Information about a single network-prefix for ATM-layer addresses in effect on the user-side IME. Note that the index variable atmNetPrefixPrefix is a variable-length string, and as such the rule for variable-length strings in section 4.1.6 of RFC 1212 applies.
atmfNetPrefixGroup	1.3.6.1.4.1.353.2.7
INT atmfNetPrefixPort	1.3.6.1.4.1.353.2.7.1.1.1	INTEGER	not-accessible	A unique value which identifies the UNI port for which the network prefix for ATM addresses is in effect. The value of 0 has the special meaning of identifying the local UNI.
NET atmfNetPrefixPrefix	1.3.6.1.4.1.353.2.7.1.1.2	NetPrefix	not-accessible	The network prefix for ATM addresses which is in effect on the user side of the ATM UNI port.
INT atmfNetPrefixStatus	1.3.6.1.4.1.353.2.7.1.1.3	INTEGER	read-write	An indication of the validity of the network prefix for ATM addresses on the user side of the UNI port. To configure a new network prefix in this table, the network-side IME must set the appropriate instance of this object to the value valid(1). To delete an existing network prefix in this table, the network-side IME must set the appropriate instance of this object to the value invalid(2). If circumstances occur on the user-side IME which cause a prefix to become invalid, the user-side IME modifies the value of the appropriate instance of this object to invalid(2). Whenever the value of this object for a particular prefix becomes invalid(2), the conceptual row for that prefix may be removed from the table at any time, either immediately or subsequently.
atmfNetPrefixTable	1.3.6.1.4.1.353.2.7.1		not-accessible	A table implemented by the user-side IME, containing the network-prefix(es) for ATM-layer addresses in effect on the user side of the UNI.
atmfNoClpNoScr	1.3.6.1.4.1.353.1.4.3
atmfNoClpScr	1.3.6.1.4.1.353.1.4.6
atmfNoDescriptor	1.3.6.1.4.1.353.1.4.1
atmForum	1.3.6.1.4.1.353
atmForumAdmin	1.3.6.1.4.1.353.1
atmForumUni	1.3.6.1.4.1.353.2
atmfPeakRate	1.3.6.1.4.1.353.1.4.2
atmfPhysicalGroup	1.3.6.1.4.1.353.2.1
ADR atmfPortAddress	1.3.6.1.4.1.353.2.1.1.1.2	AtmAddress	read-only	This object should not be implemented except as required for backward compatibility with version 2.0 of the UNI specification. The Address Group, defined in theAddress Registration MIB should be used instead.
atmfPortEntry	1.3.6.1.4.1.353.2.1.1.1		not-accessible	An entry in the table, containing information about the physical layer of an ATM Interface.
INT atmfPortIndex	1.3.6.1.4.1.353.2.1.1.1.1	INTEGER	read-only	The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received.
OID atmfPortMediaType	1.3.6.1.4.1.353.2.1.1.1.4	OBJECT IDENTIFIER	read-only	This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead.
INT atmfPortMyIfIdentifier	1.3.6.1.4.1.353.2.1.1.1.8	INTEGER	read-only	A unique value for each ATM interface. The scheme used to number the ATM interfaces on an ATM device is implementation specific. One way to generate this value is to use the ifIndex that an SNMP manager would use to identify the port. This interface must be uniquely numbered on this system to distinguish parallel links with a neighboring system.
STR atmfPortMyIfName	1.3.6.1.4.1.353.2.1.1.1.7	DisplayString	read-only	A textual name of this interface. If this system is manageable through SNMP, and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. This interface must be uniquely named on this system to distinguish parallel links with a neighboring system. If this interface does not have a textual name, the value of this object is a zero length string.
INT atmfPortOperStatus	1.3.6.1.4.1.353.2.1.1.1.5	INTEGER	read-only	This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead.
OID atmfPortSpecific	1.3.6.1.4.1.353.2.1.1.1.6	OBJECT IDENTIFIER	read-only	This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead.
atmfPortTable	1.3.6.1.4.1.353.2.1.1		not-accessible	A table of physical layer status and parameter information for the ATM Interface's physical interface.
OID atmfPortTransmissionType	1.3.6.1.4.1.353.2.1.1.1.3	OBJECT IDENTIFIER	read-only	This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead.
atmfSonetSTS12c	1.3.6.1.4.1.353.1.2.6
atmfSonetSTS3c	1.3.6.1.4.1.353.1.2.2
atmfSrvcRegistryGroup	1.3.6.1.4.1.353.2.8
atmfSrvcRegTypes	1.3.6.1.4.1.353.1.5
atmfT1	1.3.6.1.4.1.353.1.2.8
atmfTrafficDescrTypes	1.3.6.1.4.1.353.1.4
atmfTransmissionTypes	1.3.6.1.4.1.353.1.2
atmfUnknownType	1.3.6.1.4.1.353.1.2.1
atmfVccAbrEntry	1.3.6.1.4.1.353.2.10.1.1		not-accessible	An entry in the table, containing information about a particular ABR virtual channel connection.
atmfVccAbrGroup	1.3.6.1.4.1.353.2.10
INT atmfVccAbrPortIndex	1.3.6.1.4.1.353.2.10.1.1.1	INTEGER	read-only	The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received.
atmfVccAbrTable	1.3.6.1.4.1.353.2.10.1		not-accessible	A table of operational parameters related to the ABR virtual channel connections which cross this ATM Interface. There is one entry in this table for each ABR virtual channel connection. Each virtual channel connection represented in this table must also be represented by an entry in the atmfVccTable.
INT atmfVccAbrTransmitAdtf	1.3.6.1.4.1.353.2.10.1.1.10	INTEGER	read-only	ACR Decrease Time Factor: Time permitted between sending RM-cells, before the allowed rate (ACR) is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 milliseconds. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds).
INT atmfVccAbrTransmitCdf	1.3.6.1.4.1.353.2.10.1.1.7	INTEGER	read-only	Cutoff Decrease Factor: This field controls the rate decrease associated with lost or delayed backward RM cells. Larger values result in faster rate decrease. The default value is cdfOneOver16(4).
INT atmfVccAbrTransmitCrm	1.3.6.1.4.1.353.2.10.1.1.11	INTEGER	read-only	RM Cells Before Cutoff: Limits the number of forward RM-cells which may be sent in the absence of received backward RM-cells.
INT atmfVccAbrTransmitIcr	1.3.6.1.4.1.353.2.10.1.1.4	INTEGER	read-only	Initial Cell Rate: This is the rate at which the source starts, both initially and after an idle period. The unit is cells per second. The value must not be larger than PCR, and is usually lower.
INT atmfVccAbrTransmitNrm	1.3.6.1.4.1.353.2.10.1.1.5	INTEGER	read-only	The maximum number of data cells a source may send for each forward RM-cell. The default value is nrm32(5).
INT atmfVccAbrTransmitRdf	1.3.6.1.4.1.353.2.10.1.1.9	INTEGER	read-only	Rate Decrease Factor: Controls the rate decrease which occurs when backward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12).
INT atmfVccAbrTransmitRif	1.3.6.1.4.1.353.2.10.1.1.8	INTEGER	read-only	Rate Increment Factor: Controls the rate at which the rate increases, when a backward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12).
INT atmfVccAbrTransmitTrm	1.3.6.1.4.1.353.2.10.1.1.6	INTEGER	read-only	Upper bound on the time between forward RM-cells for an active source (in milliseconds). The default value is trm100(8).
INT atmfVccAbrVci	1.3.6.1.4.1.353.2.10.1.1.3	INTEGER	read-only	The VCI value of this ABR Virtual Channel Connection at the local ATM Interface.
INT atmfVccAbrVpi	1.3.6.1.4.1.353.2.10.1.1.2	INTEGER	read-only	The VPI value of this ABR Virtual Channel Connection at the local ATM Interface. For virtual interfaces (i.e. Virtual Path Connections), this value has no meaning and is set to zero
T/F atmfVccBestEffortIndicator	1.3.6.1.4.1.353.2.5.1.1.20	TruthValue	read-only	The object is examined when atmfVccTransmitTrafficDescriptorType or atmfVccReceiveTrafficDescriptorType for the associated connection is equal to atmfNoClpNoScr. If this object is set to false(2), the network is requested to apply the CBR.1 conformance definition. If this object is set to true(1), the network is requested to apply the UBR.1 conformance definition.
NTF atmfVccChange	1.3.6.1.4.1.353.0.2			An atmfVccChange trap indicates that a permanent VCC has been added or deleted at this ATM Interface or that the attributes of an existing VCC have been modified.. The variables included in the trap identify the VCI and VPI values of the reconfigured VCC at this ATM Interface.
atmfVccEntry	1.3.6.1.4.1.353.2.5.1.1		not-accessible	An entry in the table, containing information about a particular virtual channel connection.
atmfVccGroup	1.3.6.1.4.1.353.2.5
INT atmfVccOperStatus	1.3.6.1.4.1.353.2.5.1.1.4	INTEGER	read-only	The present actual operational status of the VCC. A value of end2endUp(2) or end2endUp(3) is used if the end to end status is known. If only local status is known a value of localUpEnd2endUnknown(4) or localDown(5) is used.
INT atmfVccPortIndex	1.3.6.1.4.1.353.2.5.1.1.1	INTEGER	read-only	The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received.
INT atmfVccQoSCategory	1.3.6.1.4.1.353.2.5.1.1.17	INTEGER	read-only	This object should not be implemented except as required for backward compatibility with version 2.0 of the UNI specification.
T/F atmfVccReceiveFrameDiscard	1.3.6.1.4.1.353.2.5.1.1.22	TruthValue	read-only	If set to true(1), this object indicates that the network is requested to treat data for this connection (in the receive direction) as frames (e.g. AAL5 CPCS-PDU's) rather than as individual cells. While the precise implementation is network-specific, this treatment may for example involve discarding entire frames during congestion, rather than a few cells from many frames. The default value is false(2).
INT atmfVccReceiveQoSClass	1.3.6.1.4.1.353.2.5.1.1.19	INTEGER	read-only	This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification.
INT atmfVccReceiveTrafficDescriptorParam1	1.3.6.1.4.1.353.2.5.1.1.12	INTEGER	read-only	The first parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType.
INT atmfVccReceiveTrafficDescriptorParam2	1.3.6.1.4.1.353.2.5.1.1.13	INTEGER	read-only	The second parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType.
INT atmfVccReceiveTrafficDescriptorParam3	1.3.6.1.4.1.353.2.5.1.1.14	INTEGER	read-only	The third parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType.
INT atmfVccReceiveTrafficDescriptorParam4	1.3.6.1.4.1.353.2.5.1.1.15	INTEGER	read-only	The fourth parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType.
INT atmfVccReceiveTrafficDescriptorParam5	1.3.6.1.4.1.353.2.5.1.1.16	INTEGER	read-only	The fifth parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType.
OID atmfVccReceiveTrafficDescriptorType	1.3.6.1.4.1.353.2.5.1.1.11	OBJECT IDENTIFIER	read-only	The type of traffic management, applicable to the traffic in the receive direction of this VCC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVccReceiveTrafficDescriptorParam1, atmfVccReceiveTrafficDescriptorParam2, atmfVccReceiveTrafficDescriptorParam3, atmfVccReceiveTrafficDescriptorParam4, and atmfVccReceiveTrafficDescriptorParam5.
ATM atmfVccServiceCategory	1.3.6.1.4.1.353.2.5.1.1.23	AtmServiceCategory	read-only	The service category of this virtual channel connection.
atmfVccTable	1.3.6.1.4.1.353.2.5.1		not-accessible	A table of status and parameter information on the virtual channel connections which are visible at this ATM Interface. There is one entry in this table for each permanent virtual channel connection, including reserved VCCs that are supported; e.g., signalling, OAM flows, and ILMI, but not unassigned cells.
T/F atmfVccTransmitFrameDiscard	1.3.6.1.4.1.353.2.5.1.1.21	TruthValue	read-only	If set to true(1), this object indicates that the network is requested to treat data for this connection (in the transmit direction) as frames (e.g. AAL5 CPCS-PDU's) rather than as individual cells. While the precise implementation is network-specific, this treatment may for example involve discarding entire frames during congestion, rather than a few cells from many frames. The default value is false(2).
INT atmfVccTransmitQoSClass	1.3.6.1.4.1.353.2.5.1.1.18	INTEGER	read-only	This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification.
INT atmfVccTransmitTrafficDescriptorParam1	1.3.6.1.4.1.353.2.5.1.1.6	INTEGER	read-only	The first parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType.
INT atmfVccTransmitTrafficDescriptorParam2	1.3.6.1.4.1.353.2.5.1.1.7	INTEGER	read-only	The second parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType.
INT atmfVccTransmitTrafficDescriptorParam3	1.3.6.1.4.1.353.2.5.1.1.8	INTEGER	read-only	The third parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType.
INT atmfVccTransmitTrafficDescriptorParam4	1.3.6.1.4.1.353.2.5.1.1.9	INTEGER	read-only	The fourth parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType.
INT atmfVccTransmitTrafficDescriptorParam5	1.3.6.1.4.1.353.2.5.1.1.10	INTEGER	read-only	The fifth parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType.
OID atmfVccTransmitTrafficDescriptorType	1.3.6.1.4.1.353.2.5.1.1.5	OBJECT IDENTIFIER	read-only	The type of traffic management, applicable to the transmit direction of this VCC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVccTransmitTrafficDescriptorParam1, atmfVccTransmitTrafficDescriptorParam2, atmfVccTransmitTrafficDescriptorParam3, atmfVccTransmitTrafficDescriptorParam4, and atmfVccTransmitTrafficDescriptorParam5.
INT atmfVccVci	1.3.6.1.4.1.353.2.5.1.1.3	INTEGER	read-only	The VCI value of this Virtual Channel Connection at the local ATM Interface.
INT atmfVccVpi	1.3.6.1.4.1.353.2.5.1.1.2	INTEGER	read-only	The VPI value of this Virtual Channel Connection at the local ATM Interface. For virtual interfaces (i.e. Virtual Path Connections), this value has no meaning and is set to zero
atmfVpcAbrEntry	1.3.6.1.4.1.353.2.9.1.1		not-accessible	An entry in the table, containing information about a particular ABR virtual path connection.
atmfVpcAbrGroup	1.3.6.1.4.1.353.2.9
INT atmfVpcAbrPortIndex	1.3.6.1.4.1.353.2.9.1.1.1	INTEGER	read-only	The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received.
atmfVpcAbrTable	1.3.6.1.4.1.353.2.9.1		not-accessible	A table of operational parameters related to the ABR virtual path connections which cross this ATM Interface. There is one entry in this table for each ABR virtual path connection. Each virtual path connection represented in this table must also be represented by an entry in the atmfVpcTable.
INT atmfVpcAbrTransmitAdtf	1.3.6.1.4.1.353.2.9.1.1.9	INTEGER	read-only	ACR Decrease Time Factor: Time permitted between sending RM-cells, before the allowed rate (ACR) is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 milliseconds. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds).
INT atmfVpcAbrTransmitCdf	1.3.6.1.4.1.353.2.9.1.1.6	INTEGER	read-only	Cutoff Decrease Factor: This field controls the rate decrease associated with lost or delayed backward RM cells. Larger values result in faster rate decrease. The default value is cdfOneOver16(4).
INT atmfVpcAbrTransmitCrm	1.3.6.1.4.1.353.2.9.1.1.10	INTEGER	read-only	RM Cells Before Cutoff: Limits the number of forward RM-cells which may be sent in the absence of received backward RM-cells.
INT atmfVpcAbrTransmitIcr	1.3.6.1.4.1.353.2.9.1.1.3	INTEGER	read-only	Initial Cell Rate: This is the rate at which the source starts, both initially and after an idle period. The unit is cells per second. The value must not be larger than PCR, and is usually lower.
INT atmfVpcAbrTransmitNrm	1.3.6.1.4.1.353.2.9.1.1.4	INTEGER	read-only	The maximum number of data cells a source may send for each forward RM-cell. The default value is nrm32(5).
INT atmfVpcAbrTransmitRdf	1.3.6.1.4.1.353.2.9.1.1.8	INTEGER	read-only	Rate Decrease Factor: Controls the rate decrease which occurs when backward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12).
INT atmfVpcAbrTransmitRif	1.3.6.1.4.1.353.2.9.1.1.7	INTEGER	read-only	Rate Increment Factor: Controls the rate at which the rate increases, when a backward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12).
INT atmfVpcAbrTransmitTrm	1.3.6.1.4.1.353.2.9.1.1.5	INTEGER	read-only	Upper bound on the time between forward RM-cells for an active source (in milliseconds). The default value is trm100(8).
INT atmfVpcAbrVpi	1.3.6.1.4.1.353.2.9.1.1.2	INTEGER	read-only	The VPI value of this ABR Virtual Path Connection at the local ATM Interface.
T/F atmfVpcBestEffortIndicator	1.3.6.1.4.1.353.2.4.1.1.19	TruthValue	read-only	The object is examined when atmfVpcTransmitTrafficDescriptorType or atmfVpcReceiveTrafficDescriptorType for the associated connection is equal to atmfNoClpNoScr. If this object is set to false(2), the network is requested to apply the CBR.1 conformance definition. If this object is set to true(1), the network is requested to apply the UBR.1 conformance definition.
NTF atmfVpcChange	1.3.6.1.4.1.353.0.1			An atmfVpcChange trap indicates that a permanent VPC has been added or deleted at this ATM Interface or that the attributes of an existing VPC have been modified. The variables included in the trap identify the VPI value of the reconfigured VPC at this ATM Interface.
atmfVpcEntry	1.3.6.1.4.1.353.2.4.1.1		not-accessible	An entry in the table, containing information about a particular virtual path connection.
atmfVpcGroup	1.3.6.1.4.1.353.2.4
INT atmfVpcOperStatus	1.3.6.1.4.1.353.2.4.1.1.3	INTEGER	read-only	The present actual operational status of the VPC. A value of end2endUp(2) or end2endDown(3) would be used if the end-to-end status is known. If only local status information is available, a value of localUpEnd2endUnknown(4) or localDown(5) would be used.
INT atmfVpcPortIndex	1.3.6.1.4.1.353.2.4.1.1.1	INTEGER	read-only	The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received.
INT atmfVpcQoSCategory	1.3.6.1.4.1.353.2.4.1.1.16	INTEGER	read-only	This object should not be implemented except as required for backward compatibility with version 2.0 of the UNI specification.
INT atmfVpcReceiveQoSClass	1.3.6.1.4.1.353.2.4.1.1.18	INTEGER	read-only	This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification.
INT atmfVpcReceiveTrafficDescriptorParam1	1.3.6.1.4.1.353.2.4.1.1.11	INTEGER	read-only	The first parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType.
INT atmfVpcReceiveTrafficDescriptorParam2	1.3.6.1.4.1.353.2.4.1.1.12	INTEGER	read-only	The second parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType.
INT atmfVpcReceiveTrafficDescriptorParam3	1.3.6.1.4.1.353.2.4.1.1.13	INTEGER	read-only	The third parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType.
INT atmfVpcReceiveTrafficDescriptorParam4	1.3.6.1.4.1.353.2.4.1.1.14	INTEGER	read-only	The fourth parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType.
INT atmfVpcReceiveTrafficDescriptorParam5	1.3.6.1.4.1.353.2.4.1.1.15	INTEGER	read-only	The fifth parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType.
OID atmfVpcReceiveTrafficDescriptorType	1.3.6.1.4.1.353.2.4.1.1.10	OBJECT IDENTIFIER	read-only	The type of traffic management, applicable to the traffic in the receive direction of this VPC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVpcReceiveTrafficDescriptorParam1, atmfVpcReceiveTrafficDescriptorParam2, atmfVpcReceiveTrafficDescriptorParam3, atmfVpcReceiveTrafficDescriptorParam4, and atmfVpcReceiveTrafficDescriptorParam5.
ATM atmfVpcServiceCategory	1.3.6.1.4.1.353.2.4.1.1.20	AtmServiceCategory	read-only	The service category of this virtual path connection.
atmfVpcTable	1.3.6.1.4.1.353.2.4.1		not-accessible	A table of status and parameter information on the virtual path connections which cross this ATM Interface. There is one entry in this table for each permanent virtual path connection.
INT atmfVpcTransmitQoSClass	1.3.6.1.4.1.353.2.4.1.1.17	INTEGER	read-only	This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification.
INT atmfVpcTransmitTrafficDescriptorParam1	1.3.6.1.4.1.353.2.4.1.1.5	INTEGER	read-only	The first parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType.
INT atmfVpcTransmitTrafficDescriptorParam2	1.3.6.1.4.1.353.2.4.1.1.6	INTEGER	read-only	The second parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType.
INT atmfVpcTransmitTrafficDescriptorParam3	1.3.6.1.4.1.353.2.4.1.1.7	INTEGER	read-only	The third parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType.
INT atmfVpcTransmitTrafficDescriptorParam4	1.3.6.1.4.1.353.2.4.1.1.8	INTEGER	read-only	The fourth parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType.
INT atmfVpcTransmitTrafficDescriptorParam5	1.3.6.1.4.1.353.2.4.1.1.9	INTEGER	read-only	The fifth parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType.
OID atmfVpcTransmitTrafficDescriptorType	1.3.6.1.4.1.353.2.4.1.1.4	OBJECT IDENTIFIER	read-only	The type of traffic management, applicable to the transmit direction of this VPC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVpcTransmitTrafficDescriptorParam1, atmfVpcTransmitTrafficDescriptorParam2, atmfVpcTransmitTrafficDescriptorParam3, atmfVpcTransmitTrafficDescriptorParam4, and atmfVpcTransmitTrafficDescriptorParam5.
INT atmfVpcVpi	1.3.6.1.4.1.353.2.4.1.1.2	INTEGER	read-only	The VPI value of this Virtual Path Connection at the local ATM Interface.
STR sysContact	1.3.6.1.2.1.1.4	DisplayString	read-only	The textual identification of the contact person for this managed node, together with information on how to contact this person.
STR sysDescr	1.3.6.1.2.1.1.1	DisplayString	read-only	A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters.
STR sysLocation	1.3.6.1.2.1.1.6	DisplayString	read-only	The physical location of this node (e.g., `telephone closet, 3rd floor').
STR sysName	1.3.6.1.2.1.1.5	DisplayString	read-only	An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.
OID sysObjectID	1.3.6.1.2.1.1.2	OBJECT IDENTIFIER	read-only	The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining `what kind of box' is being managed. For example, if vendor `Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.
INT sysServices	1.3.6.1.2.1.1.7	INTEGER	read-only	A value which indicates the set of services that this entity primarily offers. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. For example, a node which performs primarily routing functions would have a value of 4 (2^(3-1)). In contrast, a node which is a host offering application services would have a value of 72 (2^(4-1) + 2^(7-1)). Note that in the context of the Internet suite of protocols, values should be calculated accordingly: layer functionality 1 physical (e.g., repeaters) 2 datalink/subnetwork (e.g., bridges) 3 internet (e.g., IP gateways) 4 end-to-end (e.g., IP hosts) 7 applications (e.g., mail relays) For systems including OSI protocols, layers 5 and 6 may also be counted.
system	1.3.6.1.2.1.1
TIK sysUpTime	1.3.6.1.2.1.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the network management portion of the system was last re-initialized.

RFC description

Configures ILMI (Interim Link Management Interface) for ATM connections on Ericsson AXD301 access nodes.

Start monitoring Ericsson AXD 301 ATM switch (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AXD301-ILMI-MIB

What Is AXD301-ILMI-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description