AVIAT-SWMANAGEMENT-MIB

All MIBs › AVIAT-SWMANAGEMENT-MIB

Organization: Aviat Networks

Last Updated: 2014-01-21

Category: Vendor: Aviat

Description: Manages software image installation, upgrade scheduling, and activation status on Aviat microwave network elements.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AVIAT-SWMANAGEMENT-MIB?

AVIAT-SWMANAGEMENT-MIB is a vendor MIB from Aviat Networks, a manufacturer of microwave point-to-point radio links used in telecom backhaul, providing software image management for its microwave network elements. It exposes objects for loading a new software image onto the device, scheduling a soft reset to activate it, and retrieving details about the currently running and available software versions. This makes it a software-status monitoring MIB in the most direct sense, tracking the device's current software version, the progress/success of an in-flight upgrade, and whether a pending reset is scheduled to complete the activation. As a microwave-radio management MIB it typically works alongside Aviat's broader radio-performance and alarm MIBs rather than any IETF standard, since software-loading procedures are vendor-specific. It is deployed on Aviat microwave radio network elements used for wireless telecom backhaul links between cell sites or aggregation points, and operators managing these links can get an AVIAT-SWMANAGEMENT-MIB download to load directly into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in AVIAT-SWMANAGEMENT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Aviat Networks microwave radio (telecom backhaul link)

Monitoring Examples

No object or table names were included in the available source excerpt, so a concrete polling scenario with grounded names cannot be given; based on its stated purpose, an operator upgrading firmware fleet-wide would expect to poll objects analogous to a software-version and upgrade-status table to confirm a microwave link's software image has finished loading and that the scheduled soft reset completed without leaving the radio in a stale or failed-upgrade state.

Imported Objects

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DateAndTime
DisplayString

From STXN-GLOBALREGISTER-MIB

aviatModules

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
aviatSwManagementModule	1.3.6.1.4.1.2509.9.11			This MIB defines the interface for software loading, soft reset and software details retrieval.
aviatSwManagementConf	1.3.6.1.4.1.2509.9.11.1
aviatSwManagementGroups	1.3.6.1.4.1.2509.9.11.1.1
aviatSwResetGroup	1.3.6.1.4.1.2509.9.11.1.1.1			These are the software reset objects.
aviatSwLoadGroup	1.3.6.1.4.1.2509.9.11.1.1.2			These are the objects for software loading.
aviatSwDetailsGroup	1.3.6.1.4.1.2509.9.11.1.1.3			These are the software details objects.
aviatSwManagementCompliance	1.3.6.1.4.1.2509.9.11.1.2
aviatSwManagementComplV1	1.3.6.1.4.1.2509.9.11.1.2.1			The implementation requirements for this MIB.
aviatSwManagementMIBObjects	1.3.6.1.4.1.2509.9.11.2
aviatSwResetObjects	1.3.6.1.4.1.2509.9.11.2.1
INT aviatSmSoftReset	1.3.6.1.4.1.2509.9.11.2.1.1	INTEGER	read-write	This is the control to perform a software reset on the product. When set to resetSoft(1) a soft reset will be performed. When set to resetHard(2) a full system reset will be performed, with all reinitialisation carried out. Setting to resetNone(0) has no effect.
aviatSwLoadObjects	1.3.6.1.4.1.2509.9.11.2.2
INT aviatSmLoadControl	1.3.6.1.4.1.2509.9.11.2.2.1	INTEGER	read-write	The software loading process may be controlled using this object. Setting the value load(1) will begin transfer of the specified file from the external URI to the unit. If the file is a manifest, this will initiate transfer of all referenced files. When this procedure has completed, aviatSmLoadStatus will indicate loadOk(6) for success, or loadError(10) for failure. An unresolvable incompatibility error is indicated by compatibilityError(13) and should be followed by an abort(0). A successful software (loadOk) load may be activated by setting the value to activate(2). If the delayed/timed activation objects are disabled this will have an immediate effect, otherwise the activation will take place as scheduled. A successful activation will result in an aviatSmLoadStatus value of activateOk(7). An error will be indicated by the value activateError(11). If the value is idle(7) and no software load process has been initiated since the last successful activation, the inactive software can be re-activated by setting the value to rollback(4). Success is indicated in aviatSmLoadStatus by rollbackOk(8) and failure by rollbackError(12). Setting the value to loadAndActivate(3) will begin software transfer. A successful transfer will be followed by software activation which is controlled by the delayed/timed activation objects. Success will be indicated in aviatSmLoadStatus by activateOk(7). A pending scheduled activation is indicated by waitingToActivate(13).
INT aviatSmLoadStatus	1.3.6.1.4.1.2509.9.11.2.2.2	INTEGER	read-only	The software loading process may be monitored using this object. See the aviatSmLoadControl object description for more details.
I32 aviatSmLoadRollbackDuration	1.3.6.1.4.1.2509.9.11.2.2.3	Integer32	read-write	This specifies the duration, in seconds, from which the 'sw load rollback timer' will count down when it is started.
I32 aviatSmLoadRollbackTimer	1.3.6.1.4.1.2509.9.11.2.2.4	Integer32	read-write	This is the control and counter of the 'sw load rollback timer'. When set to -1, the timer is stopped and disabled. When set to 0, the timer assumes an 'instant timeout'. Otherwise, this object will indicate the time left on the timer. The timer is automatically started whenever the software starts up following a software load activation. When this timer reaches zero, the 'sw load manager' of the system will roll back the software to its previous version.
I32 aviatSmLoadActivateWaitDuration	1.3.6.1.4.1.2509.9.11.2.2.5	Integer32	read-write	This specifies the duration, in seconds, from which the 'sw load activate wait timer' will count down when it is started.
I32 aviatSmLoadActivateWaitTimer	1.3.6.1.4.1.2509.9.11.2.2.6	Integer32	read-write	This is the control and counter of the 'sw load activate wait timer'. When set to -1, the timer is stopped and disabled. When set to 0, the timer assumes an 'instant timeout'. Otherwise, this object will indicate the time left on the timer. This timer is loaded with the lesser of aviatSmLoadActivateWaitDuration (if non-zero), or the time in seconds until aviatSmLoadActivateTime occurs (if set) when the activate(2) state is entered. When this timer reaches zero, the 'sw load manager' of the system will activate the loaded software.
DAT aviatSmLoadActivateTime	1.3.6.1.4.1.2509.9.11.2.2.7	DateAndTime	read-write	This determines the date and time at which to activate the loaded software. The 'sw load manager' of the system shall activate the loaded software when the current system time reaches or is past this setting.
STR aviatSmLoadUri	1.3.6.1.4.1.2509.9.11.2.2.8	DisplayString	read-write	The URI of the manifest for software loading.
I32 aviatSmLoadProgress	1.3.6.1.4.1.2509.9.11.2.2.9	Integer32	read-only	The percentage progress of the current sofware load. It is only meaningful during load and commit, and will return zero otherwise.
aviatSwDetailsObjects	1.3.6.1.4.1.2509.9.11.2.3
STR aviatSmDetailsVersion	1.3.6.1.4.1.2509.9.11.2.3.1	DisplayString	read-only	The software version of currently running software.
STR aviatSmDetailsInactiveVersion	1.3.6.1.4.1.2509.9.11.2.3.2	DisplayString	read-only	The software version of the inactive software.

RFC description

Manages software loading, soft reset, and software details retrieval for Aviat Networks wireless transmission equipment.

Start monitoring Aviat Networks microwave radio links (point-to-point backhaul) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AVIAT-SWMANAGEMENT-MIB

What Is AVIAT-SWMANAGEMENT-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description