AVIAT-RF-MIB

All MIBs › AVIAT-RF-MIB

Organization: Aviat Networks

Last Updated: 2015-11-05

Category: Vendor: Aviat

Description: Tracks RF parameters of Aviat microwave units, including transmit power, receive level, and frequency settings.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AVIAT-RF-MIB?

AVIAT-RF-MIB is a MIB from Aviat Networks supporting the RF (radio frequency) fault-management functions of its point-to-point microwave radio equipment. It exposes parameters covering the radio's RF-layer operation - transmit power, receive signal level, and frequency/channel configuration - which together characterize the health and configuration of the microwave link's radio front-end. This MIB is fundamentally a hardware-status and fault-monitoring module: it is used to watch for degraded RF conditions such as low receive signal level or abnormal transmit power that indicate antenna misalignment, weather fade, or hardware degradation on the microwave link, rather than general software status. It ties into Aviat's broader radio-system MIB suite (alarm, chassis, and modem MIBs) since RF-layer faults are typically correlated with alarms defined elsewhere in the vendor's MIB tree. It is deployed on Aviat microwave backhaul radios used by mobile operators and utilities for point-to-point wireless transport links. Engineers can download the AVIAT-RF-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in AVIAT-RF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Aviat Networks microwave point-to-point radio

Monitoring Examples

Although no specific object names were provided in the input, an RF fault-management MIB of this kind is used the way this description implies: an operator polls transmit-power and receive-level objects on each radio link end to detect a drop in received signal strength (often signaling antenna misalignment or path fade) and cross-checks the configured frequency/channel objects to confirm the link has not drifted from its planned RF configuration.

What Can Be Monitored

transmit power level
receive signal level
operating frequency/channel configuration
RF fault/alarm status

Imported Objects

From AVIAT-TEXTCONVENTION-MIB

AviatDecibel
AviatModulationType
AviatPowerLevel
AviatRfuSideBandType

From ENTITY-MIB

entPhysicalIndex

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Gauge32
Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

TruthValue

From STXN-GLOBALREGISTER-MIB

aviatModules

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
aviatRfModule	1.3.6.1.4.1.2509.9.5			This MIB module supports the RF Fault Management functions of the radio.
aviatRfConformance	1.3.6.1.4.1.2509.9.5.1
aviatRfGroups	1.3.6.1.4.1.2509.9.5.1.1
aviatRfObjectGroup	1.3.6.1.4.1.2509.9.5.1.1.1			These objects specify the RF capabilities and settings of the unit.
aviatRfCompliance	1.3.6.1.4.1.2509.9.5.1.2
aviatRfComplV1	1.3.6.1.4.1.2509.9.5.1.2.1			The implementation requirements for this MIB.
aviatRfMIBObjects	1.3.6.1.4.1.2509.9.5.2
aviatRfConfigTable	1.3.6.1.4.1.2509.9.5.2.1		not-accessible	A table containing the RF configuration objects for a particular entity of the system.
aviatRfConfigEntry	1.3.6.1.4.1.2509.9.5.2.1.1		not-accessible	This is a row in the RF configuration table.
I32 aviatRfFreqTx	1.3.6.1.4.1.2509.9.5.2.1.1.1	Integer32	read-write	This specifies the transmit frequency of the unit.
I32 aviatRfFreqRx	1.3.6.1.4.1.2509.9.5.2.1.1.2	Integer32	read-write	This specifies the receive frequency of the unit.
AVI aviatRfPowerSet	1.3.6.1.4.1.2509.9.5.2.1.1.3	AviatPowerLevel	read-write	This specifies the desired output power for the transmitter of the unit.
T/F aviatRfTxMute	1.3.6.1.4.1.2509.9.5.2.1.1.4	TruthValue	read-write	This specifies the status of the factory mute of the unit. If set to TRUE, the transmitter output will be muted. It should be set to FALSE otherwise. This setting is 'ORed' with other conditions (including diagnostic functions and configuration validation) to control the transmitter output status.
T/F aviatRfHighGain	1.3.6.1.4.1.2509.9.5.2.1.1.5	TruthValue	read-write	This specifies whether to assign a high power license to this RF interface. If set to TRUE a license has been assigned, FALSE otherwise.
INT aviatRfBandSelection	1.3.6.1.4.1.2509.9.5.2.1.1.6	INTEGER	read-write	This is used to select a sub-band within the frequency range of the attached RFU. It is intended to limit the frequencies available for configuration of the RFU.
aviatRfATPCTable	1.3.6.1.4.1.2509.9.5.2.2		not-accessible	A table containing the RF ATPC configuration objects for a particular entity of the system.
aviatRfATPCEntry	1.3.6.1.4.1.2509.9.5.2.2.1		not-accessible	This is a row in the RF ATPC table.
T/F aviatRfATPCEnabled	1.3.6.1.4.1.2509.9.5.2.2.1.1	TruthValue	read-write	This is the control to enable or disable the Automatic Transmit Power Control (ATPC) function on the unit.
AVI aviatRfATPCTargetFadeMargin	1.3.6.1.4.1.2509.9.5.2.2.1.2	AviatDecibel	read-write	This specifies the desired nominal fade margin that the Automatic Transmit Power Control function should attempt to maintain.
AVI aviatRfATPCMaximumPower	1.3.6.1.4.1.2509.9.5.2.2.1.3	AviatPowerLevel	read-write	This specifies the maximum power level that the Automatic Transmit Power Control function may set.
AVI aviatRfATPCMinimumPower	1.3.6.1.4.1.2509.9.5.2.2.1.4	AviatPowerLevel	read-write	This specifies the minimum power level that the Automatic Transmit Power Control function may set.
T/F aviatRfATPCFCCCompliant	1.3.6.1.4.1.2509.9.5.2.2.1.5	TruthValue	read-write	This is the control to enable or disable the Federal Communications Commission (FCC) compliant Automatic Transmit Power Control function.
aviatRfuCapabilityTable	1.3.6.1.4.1.2509.9.5.2.3		not-accessible	A table containing the capabilities of an attached RFU.
aviatRfuCapabilityEntry	1.3.6.1.4.1.2509.9.5.2.3.1		not-accessible	This is a row in the RFU capabilities table.
I32 aviatRfuTxFreqMax	1.3.6.1.4.1.2509.9.5.2.3.1.1	Integer32	read-only	The RFU maximum transmit frequency capability.
I32 aviatRfuTxFreqMin	1.3.6.1.4.1.2509.9.5.2.3.1.2	Integer32	read-only	The RFU minimum Tx frequency capability.
I32 aviatRfuRxFreqMax	1.3.6.1.4.1.2509.9.5.2.3.1.3	Integer32	read-only	The RFU maximum Rx frequency capability.
I32 aviatRfuRxFreqMin	1.3.6.1.4.1.2509.9.5.2.3.1.4	Integer32	read-only	The RFU minimum Rx frequency capability.
I32 aviatRfuFreqStepMin	1.3.6.1.4.1.2509.9.5.2.3.1.5	Integer32	read-only	The RFU minimum frequency step size capability.
I32 aviatRfuBandwidthMax	1.3.6.1.4.1.2509.9.5.2.3.1.6	Integer32	read-only	The RFU maximum bandwidth capability.
I32 aviatRfuTxRxSpacingMax	1.3.6.1.4.1.2509.9.5.2.3.1.7	Integer32	read-only	The RFU maximum Tx Rx spacing capability.
I32 aviatRfuTxRxSpacingMin	1.3.6.1.4.1.2509.9.5.2.3.1.8	Integer32	read-only	The RFU minimum Tx Rx spacing capability.
I32 aviatRfuTxPowerMax	1.3.6.1.4.1.2509.9.5.2.3.1.9	Integer32	read-only	The RFU maximum Tx power capability.
I32 aviatRfuTxPowerMin	1.3.6.1.4.1.2509.9.5.2.3.1.10	Integer32	read-only	The RFU minimum Tx power capability.
I32 aviatRfuPowerStep	1.3.6.1.4.1.2509.9.5.2.3.1.11	Integer32	read-only	The RFU power step capability.
I32 aviatRfuNoiseFigure	1.3.6.1.4.1.2509.9.5.2.3.1.12	Integer32	read-only	The RFU noise figure capability.
AVI aviatRfuModulationMax	1.3.6.1.4.1.2509.9.5.2.3.1.13	AviatModulationType	read-only	This RFU maximum modulation capability.
T/F aviatRfuTxRxSpacingPreset	1.3.6.1.4.1.2509.9.5.2.3.1.14	TruthValue	read-only	Indicates if the valid RFU Tx Rx spacing range is limited to the preset values provided by aviatRfuTxSpacingTable.
AVI aviatRfuTxSideBand	1.3.6.1.4.1.2509.9.5.2.3.1.15	AviatRfuSideBandType	read-only	Indicates the RFU side band.
I32 aviatRfuTxPowerLimit	1.3.6.1.4.1.2509.9.5.2.3.1.16	Integer32	read-only	RFU maximum Tx power limit for any modulation.
aviatRfuTxSpacingTable	1.3.6.1.4.1.2509.9.5.2.4		not-accessible	A table containing the allowed spacings for an attached RFU.
aviatRfuTxSpacingEntry	1.3.6.1.4.1.2509.9.5.2.4.1		not-accessible	This is a row in the RFU Tx spacing table.
G32 aviatRfuTxSpacingIndex	1.3.6.1.4.1.2509.9.5.2.4.1.1	Gauge32	not-accessible	An index representing a TxRx Spacing entry for an entity.
I32 aviatRfuTxSpacingFreq	1.3.6.1.4.1.2509.9.5.2.4.1.2	Integer32	read-only	A TxRx spacing entry valid for the system.
aviatRfuDetailsTable	1.3.6.1.4.1.2509.9.5.2.5		not-accessible	A table containing the details of an attached RFU.
aviatRfuDetailsEntry	1.3.6.1.4.1.2509.9.5.2.5.1		not-accessible	This is a row in the RFU details table.
I32 aviatRfuType	1.3.6.1.4.1.2509.9.5.2.5.1.1	Integer32	read-only	The type indentification of the attached RFU.
I32 aviatRfuFreqBand	1.3.6.1.4.1.2509.9.5.2.5.1.2	Integer32	read-only	The frequency band indication of the attached RFU.
I32 aviatRfuPowerAmp	1.3.6.1.4.1.2509.9.5.2.5.1.3	Integer32	read-only	The power amplifier type of the attached RFU.
INT aviatRfuSemiconductorTech	1.3.6.1.4.1.2509.9.5.2.5.1.4	INTEGER	read-only	The semiconductor technology used in the power amplifier of the attached RFU. This is used to determine whether IDQ optimization is necessary for GaN type devices.
T/F aviatRfuUnlicensed5G8Cap	1.3.6.1.4.1.2509.9.5.2.5.1.5	TruthValue	read-only	Indicates that a 5.8GHz capable RFU is attached. This unit can operate across frequency ranges which are unlicensed in some markets.
T/F aviatRfuExternalCoaxPresent	1.3.6.1.4.1.2509.9.5.2.5.1.6	TruthValue	read-only	Indicates if an external RF switch is present.

RFC description

Monitors Aviat microwave RF unit parameters including transmit power, receive level, and frequency configuration.

Start monitoring Aviat Networks microwave radio links (point-to-point backhaul) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AVIAT-RF-MIB

What Is AVIAT-RF-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description