| OID symbolic | OID numeric | Type | Access | Description |
|---|
| atmForum | 1.3.6.1.4.1.353 | | | |
| atmForumNetworkManagement | 1.3.6.1.4.1.353.5 | | | |
| atmfSignalling | 1.3.6.1.4.1.353.5.9 | | | |
| atmfRerouting | 1.3.6.1.4.1.353.5.9.3 | | | |
| atmfreroutingMIB | 1.3.6.1.4.1.353.5.9.3.1 | | | The MIB module for managing the ATM Forum
Domain-based rerouting for active point-to-point calls v1.0 |
| reroutingMIBObjects | 1.3.6.1.4.1.353.5.9.3.1.1 | | | |
| reroutingBaseGroup | 1.3.6.1.4.1.353.5.9.3.1.1.1 | | | |
| INT reroutingVersion | 1.3.6.1.4.1.353.5.9.3.1.1.1.1 | INTEGER | read-only | The version of the ATM Forum rerouting specification
that the software in this switching system is capable of
executing. |
| BIT reroutingCapabilitiesSupported | 1.3.6.1.4.1.353.5.9.3.1.1.1.2 | Bits | read-only | Indicates the rerouting mechanisms supported on
this switching system |
| U32 reroutingHardReroutingTime | 1.3.6.1.4.1.353.5.9.3.1.1.1.3 | Unsigned32 | read-write | The timeout value in milliseconds for a hard rerouting
operation to be completed. The hard rerouting timer is set
to this value when a hard rerouting operation is triggered.
A value of zero indicates that there is no timeout |
| reroutingFilterTable | 1.3.6.1.4.1.353.5.9.3.1.1.2 | | not-accessible | The table is used to configure the rerouting services of a
call during the initial call establishment. The configuration
includes:
- the availability of rerouting services,
- the request for inter and intra-domain rerouting services.
- the applicability of the configuration to svc, spvc, svp,
spvp.
The configuration of rerouting services is based on a filter.
Incoming setups and outgoing setups on inter-domain interfaces
(e.g. UNI, AINI, inter-domain PNNI) are matched against the
filters contained in this table. The configuration of the
rerouting services contained in a row of this table apply if
the setup message matches the filtering criteria contained
in the row.
If the setup message matches several filters of this table,
the resulting configuration of the rerouting services is
implementation dependent.
An entry in this table configures the rerouting services for
SVCs, SVPs, soft PVCs, and soft PVPs. The configuration
Applies to point-to-point calls only. |
| reroutingFilterEntry | 1.3.6.1.4.1.353.5.9.3.1.1.2.1 | | not-accessible | Each entry in this table defines a filter to match against
incoming/outgoing setups on inter-domain interfaces. Each
entry also contains the configuration of the rerouting
services for a call matching the filter.
Matching is performed on incoming setup indications and
Outgoing setup requests of svcs and svps when the switching
system is the edge switch for the call. The matching is done
on the inter-domain interface.
A setup message is matching a filter entry, if all the
attributes contained in the filter match the setup message.
The matching criteria is contained in the description of each
object.
The entry is also used to configure the rerouting services for
soft pvcs or soft pvps whose terminating legs are located on
an interface of this switch.
A new entry can be created by specifying an atmTraceFilterIndex
value that is currently not being used and also using an
appropriate value (createAndGo or createAndWait) for the
reroutingFilterRowStatus object.
The reroutingFilterIndex is used as the instance ID to
Uniquely identify a filter configured on this switching
system. |
| INT reroutingFilterIndex | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.1 | INTEGER | not-accessible | An arbitrary integer uniquely identifying a filter
in this table. |
| INT reroutingFilterIfDirection | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.2 | INTEGER | read-create | The combination of this object and the corresponding instance
of reroutingFilterInterface is one selection criteria for
this filter entry. If the value of this object is different
from 'none', the object restricts the scope of the filter to
calls which enter, exit or both enter and exit the ATM device
through the port represented by reroutingFilterInterface.
Calls initiated or terminated at this port (e.g. Soft PVCs)
are also scoped.
When this object has the value 'none', it indicates that the
scope of the filter is not restricted by the port. |
| NUM reroutingFilterInterface | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.3 | InterfaceIndex | read-create | The combination of this object and the corresponding instance
of reroutingIfDirection is one selection criteria
for this filter entry. This object restricts the scope of the
filter to calls which enter, exit or both enter and exit the
ATM device through the port represented by this object. Calls
initiated or terminated at this port (e.g. Soft PVCs) are also
scoped.
When reroutingFilterCallDirection has the value 'none', the
value contained in this object is ignored and the scope
of the filter is not restricted by the port. |
| BIT reroutingFilterConnKind | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.4 | Bits | read-create | Indicates if the configuration defined in this entry applies
to:
- 'svcAndSpvcNotInitiator' to switched virtual channels only.
- 'spvcInitiator' to soft permanent virtual channels,
when initiated or terminated on this switching system.
- 'svpAndSpvpNotInitiator' to switched virtual paths only.
- 'spvpInitiator' to soft permanent virtual paths,
when initiated or terminated on this switching system. |
| BIT reroutingFilterServiceCategory | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.5 | Bits | read-create | This object restricts the scope of the filter to calls
belonging to service categories represented by this object. |
| ATM reroutingFilterCallingPartyPrefix | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.6 | AtmAddr | read-create | The combination of this object and the corresponding instance
of reroutingFilterCallingPartyLength is one selection criteria
for this record. To match this selection criteria, a
call setup must have a Calling Party Address which has
an initial part (of length reroutingFilterCalledPartyLength
bits) equal in value to reroutingFilterCallingParty. When
the default value for the object is retained then the call
will match this filtering criteria for any calling address in
the call, or if the calling party number is not present in the
call. The value must be padded with zeros from
reroutingFilterCallingPartyLength to the full length of the
address (8 octets for E.164 numbers and 20 octets for AESAs). |
| I32 reroutingFilterCallingPartyLength | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.7 | Integer32 | read-create | This object specifies the number of bits in
reroutingFilterCallingParty that shall be used when matching
against the calling party of a new call setup. |
| ATM reroutingFilterCalledPartyPrefix | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.8 | AtmAddr | read-create | The combination of this object and the corresponding instance
of reroutingFilterCalledPartyLength is one selection criteria
for this record. To match this selection criteria, a
connection segment setup must have a called party address
which has an initial part (of length
reroutingFilterCalledPartyLength bits) equal in value to
reroutingFilterCalledParty. When the default value for the
object is retained then the call will match this filtering
criteria for any called address in the all. The value must be
padded with zeros from reroutingFilterCalledPartyLength to
the full length of the address (8 octets for E.164 numbers and
20 octets for AESAs). |
| I32 reroutingFilterCalledPartyLength | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.9 | Integer32 | read-create | This object specifies the number of bits in
reroutingFilterCalledParty that shall be used when matching
against the called party of a new call setup. |
| NET reroutingFilterNetworkServicesAvailable | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.10 | NetworkReroutingCapabilities | read-create | Indicates what network rerouting services are
locally available for a call when it matches this filter.
If a rerouting service is not available, the negotiation
protocol of rerouting services ensures that the service
cannot be activated for the call within this rerouting domain.
This object can be used to filter and disable the services
requested by a user.
The determination of the values indicated in the
Rerouting Service IE is described in sections 6.2.1 and
6.3.2. |
| HAR reroutingFilterHardReroutingServiceRequest | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.11 | HardReroutingServicesClass | read-create | Indicates which hard rerouting service is requested by the
network on behalf of the user when a setup matches this
address filter.
'none' means that no hard rerouting service is requested
for the call.
'dbrInterDomainHardRerouting' means that the Domain-based
hard rerouting service is requested end to end for
the call. In addition the intra-domain hard rerouting service
is requested for the call. Conditions for the request the
inter-domain hard rerouting service are described in sections
6.2.1 and 6.3.2.
'dbrIntraDomainHardRerouting' means that the Domain-based
hard rerouting service is requested for the call
within this rerouting domain only. This value can be set if
the switch is connected directly to the ATM end system, or if
it is connected to another switch with an inter-domain
interface (e.g. AINI, UNI, inter-domain PNNI)
The service specified in this object is only requested for the
call if the service is available for this interface.
(see object reroutingFilterNetworkServicesAvailable).
The determination of the activation of the service depends on
the service availability at the other edge nodes. The
procedures are described in sections 6.2.1 and 6.3.2. |
| SOF reroutingFilterSoftReroutingServiceRequest | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.12 | SoftReroutingServicesClass | read-create | Indicates which soft rerouting service is requested by the
network on behalf of the user when a setup matches this
address filter.
'none' means that no soft rerouting service is requested
for the call.
'dbrIntraDomainAsymmetricSoftRerouting' means that the
Domain-based asymmetric soft rerouting service is requested
for the call within this rerouting domain only. This value
can be set if the switch is connected directly to the ATM end
system, or if it is connected to another switch with an
inter-domain interface (e.g. AINI, UNI, inter-domain PNNI)
'dbrIntraDomainSymmetricSoftRerouting' means that the
Domain-based symmetric soft rerouting service is requested
for the call within this rerouting domain only. This value
can be set if the switch is connected directly to the
ATM end system, or if it is connected to another switch with
an inter-domain interface (e.g. AINI, UNI, inter-domain PNNI)
The service specified in this object is only requested for the
call if the service is available for this interface.
(see object reroutingFilterInterNetworkServicesAvailable)
The determination of the activation of the service depends on
the service availability at the other edge nodes. The
procedures are described in sections 6.2.1 and 6.3.2. |
| ROW reroutingFilterRowStatus | 1.3.6.1.4.1.353.5.9.3.1.1.2.1.13 | RowStatus | read-create | To create, delete, activate and de-activate a
filter for the configuration of the rerouting
services. |
| reroutingVpTable | 1.3.6.1.4.1.353.5.9.3.1.1.3 | | not-accessible | The table used to describe the rerouting
attributes of a Pt-to-Pt svp or spvp.
The entire reroutingVpTable is read-only reflecting
the fact that reroutable connections are created
through the ATM signalling protocol rather than configured. |
| reroutingVpEntry | 1.3.6.1.4.1.353.5.9.3.1.1.3.1 | | not-accessible | Each entry in this table contains the rerouting
attributes of a SVP or Soft PVP connection.
The content of this table reflects only the rerouting values
associated with VPCs. This table is similar to the atmVclTable
specified in ATM-MIB (RFC 2515).
Entries are included for Vpls for which this is the source
interface or the destination interface in the rerouting
domain. Entries may be included for Vpls at the endpoints
of the connection (see the
reroutingVpHardReroutingServiceActivated object).
This entry serves to identify the VPL on the interface. |
| RER reroutingVpNodeRole | 1.3.6.1.4.1.353.5.9.3.1.1.3.1.1 | ReroutingNodeRole | read-only | Indicates if the switch is the source node or the
destination node for the call. |
| ATM reroutingVpRemoteNodeAddress | 1.3.6.1.4.1.353.5.9.3.1.1.3.1.2 | AtmAddr | read-only | Contains the ATM address of the remote edge node |
| HAR reroutingVpHardReroutingServiceActivated | 1.3.6.1.4.1.353.5.9.3.1.1.3.1.3 | HardReroutingServicesClass | read-only | Indicates which hard rerouting service is activated for
this call.
'none' means that no hard rerouting service is activated
for the call.
On a switch, 'dbrInterDomainHardRerouting' means that the
Domain-based hard rerouting service has been requested end to
end for the call, and that it is activated within this
rerouting domain.
On an end system, 'dbrInterDomainHardRerouting' means
the hard rerouting service has been requested end to end
for the call, and that at least one rerouting domain along
the path has activated it.
'dbrIntraDomainHardRerouting' means that the Domain-based
hard rerouting service is activated for the call
within this rerouting domain only. |
| SOF reroutingVpSoftReroutingServiceActivated | 1.3.6.1.4.1.353.5.9.3.1.1.3.1.4 | SoftReroutingServicesClass | read-only | Indicates which soft rerouting service is activated for this
call.
'none' means that no soft rerouting service is activated
for the call.
'dbrIntraDomainAsymmetricSoftRerouting' means that the
Domain-based asymmetric soft rerouting service is activated
for the call within this rerouting domain only.
'dbrIntraDomainSymmetricSoftRerouting' means that the
Domain-based symmetric soft rerouting service is activated
for the call within this rerouting domain only. |
| RER reroutingVpReroutingState | 1.3.6.1.4.1.353.5.9.3.1.1.3.1.5 | ReroutingState | read-only | Indicates if a rerouting operation is in progress
and what type of rerouting operation is in progress.
'idle' indicates that no rerouting operation is
in progress.
'hardRerouting' indicates that a hard rerouting operation
is in progress.
'softRerouting' indicates that a soft rerouting operation
is in progress. |
| C32 reroutingVpReroutingOperationSuccessCounterEx | 1.3.6.1.4.1.353.5.9.3.1.1.3.1.6 | Counter32 | read-only | Indicates the number of rerouting operations
initiated by this node that succeeded on this call.
The establishment of the initial call is not counted |
| C32 reroutingVpReroutingOperationFailuresCounter | 1.3.6.1.4.1.353.5.9.3.1.1.3.1.7 | Counter32 | read-only | Indicates the number of rerouting operations
initiated by this node that failed on this call. |
| INT reroutingVpLocalIncarnationNumber | 1.3.6.1.4.1.353.5.9.3.1.1.3.1.8 | INTEGER | read-only | Indicates the current local incarnation number associated
with the call. The value contained in this object is the
incarnation number of the last reroute setup that was
sent by this node for this call.
The value zero indicates that no reroute setup has been
sent for this call.
This object is not instantiated if this node is
the destination node of the call and symmetric soft
rerouting is not activated for the call |
| INT reroutingVpRemoteIncarnationNumber | 1.3.6.1.4.1.353.5.9.3.1.1.3.1.9 | INTEGER | read-only | Indicates the current remote incarnation number associated
with the call. The value contained in this object is the
incarnation number of the last reroute setup that was
received by this node for this call.
The value zero indicates that no reroute setup has been
received for this call.
This object is not instantiated if this node is
the source node of the call and symmetric soft
rerouting is not activated for the call |
| EXT reroutingVpExtendedReroutingState | 1.3.6.1.4.1.353.5.9.3.1.1.3.1.10 | ExtendedReroutingState | read-only | Indicates the current rerouting state of the call,
as defined in the rerouting Finite State Machine. |
| reroutingVcTable | 1.3.6.1.4.1.353.5.9.3.1.1.4 | | not-accessible | The table used to describe the rerouting related
attributes of a Pt-to-Pt svc or spvc.
The entire reroutingVcTable is read-only reflecting
the fact that reroutable connections are created
through the ATM signalling protocol rather than configured. |
| reroutingVcEntry | 1.3.6.1.4.1.353.5.9.3.1.1.4.1 | | not-accessible | Each entry in this table contains the rerouting
attributes of a SVC or Soft PVC connection.
The content of this table reflects only the rerouting values
associated with VCCs. This table is similar to the atmVclTable
specified in ATM-MIB (RFC 2515).
Entries are included for Vcls for which this is the source
interface or the destination interface in the rerouting
domain. Entries may be included for Vcls at the endpoints
of the connection (see the
reroutingVcHardReroutingServiceActivated object).
This entry serves to identify the VCL on the interface. |
| RER reroutingVcNodeRole | 1.3.6.1.4.1.353.5.9.3.1.1.4.1.1 | ReroutingNodeRole | read-only | Indicates if the switch is the source node or the
destination node for the call. |
| ATM reroutingVcRemoteNodeAddress | 1.3.6.1.4.1.353.5.9.3.1.1.4.1.2 | AtmAddr | read-only | Contains the ATM address of the remote edge node |
| HAR reroutingVcHardReroutingServiceActivated | 1.3.6.1.4.1.353.5.9.3.1.1.4.1.3 | HardReroutingServicesClass | read-only | Indicates which hard rerouting service is activated for
this call.
'none' means that no hard rerouting service is activated
for the call.
On a switch, 'dbrInterDomainHardRerouting' means that the
Domain-based hard rerouting service has been requested end to
end for the call, and that it is activated within this
rerouting domain.
On an end system, 'dbrInterDomainHardRerouting' means
the hard rerouting service has been requested end to end
for the call, and that at least one rerouting domain along
the path has activated it.
'dbrIntraDomainHardRerouting' means that the Domain-based
hard rerouting service is activated for the call
within this rerouting domain only. |
| SOF reroutingVcSoftReroutingServiceActivated | 1.3.6.1.4.1.353.5.9.3.1.1.4.1.4 | SoftReroutingServicesClass | read-only | Indicates which soft rerouting service is activated for this
call.
'none' means that no soft rerouting service is activated
for the call.
'dbrIntraDomainAsymmetricSoftRerouting' means that the
Domain-based asymmetric soft rerouting service is activated
for the call within this rerouting domain only.
'dbrIntraDomainSymmetricSoftRerouting' means that the
Domain-based symmetric soft rerouting service is activated
for the call within this rerouting domain only. |
| RER reroutingVcReroutingState | 1.3.6.1.4.1.353.5.9.3.1.1.4.1.5 | ReroutingState | read-only | Indicates if a rerouting operation is in progress
and what type of rerouting operation is in progress.
'idle' indicates that no rerouting operation is
in progress.
'hardRerouting' indicates that a hard rerouting operation
is in progress.
'softRerouting' indicates that a soft rerouting operation
is in progress. |
| C32 reroutingVcReroutingOperationSuccessCounter | 1.3.6.1.4.1.353.5.9.3.1.1.4.1.6 | Counter32 | read-only | Indicates the number of rerouting operations
initiated by this node that succeeded on this call.
The establishment of the initial call is not counted |
| C32 reroutingVcReroutingOperationFailuresCounter | 1.3.6.1.4.1.353.5.9.3.1.1.4.1.7 | Counter32 | read-only | Indicates the number of rerouting operations
initiated by this node that failed on this call. |
| INT reroutingVcLocalIncarnationNumber | 1.3.6.1.4.1.353.5.9.3.1.1.4.1.8 | INTEGER | read-only | Indicates the current local incarnation number associated
with the call. The value contained in this object is the
incarnation number of the last reroute setup that was
sent by this node for this call.
The value zero indicates that no reroute setup has been
sent for this call.
This object is not instantiated if this node is
the destination node of the call and symmetric soft
rerouting is not activated for the call |
| INT reroutingVcRemoteIncarnationNumber | 1.3.6.1.4.1.353.5.9.3.1.1.4.1.9 | INTEGER | read-only | Indicates the current remote incarnation number associated
with the call. The value contained in this object is the
incarnation number of the last reroute setup that was
received by this node for this call.
The value zero indicates that no reroute setup has been
received for this call.
This object is not instantiated if this node is
the source node of the call and symmetric soft
rerouting is not activated for the call |
| EXT reroutingVcExtendedReroutingState | 1.3.6.1.4.1.353.5.9.3.1.1.4.1.10 | ExtendedReroutingState | read-only | Indicates the current rerouting state of the call,
as defined in the rerouting Finite State Machine. |
| reroutingMIBConformance | 1.3.6.1.4.1.353.5.9.3.1.2 | | | |
| reroutingMIBCompliances | 1.3.6.1.4.1.353.5.9.3.1.2.1 | | | |
| reroutingMIBCompliance | 1.3.6.1.4.1.353.5.9.3.1.2.1.1 | | | The compliance statement for entities which implement
the ATM rerouting MIB.
Groups of required rerouting objects for configuring and
monitoring the domain-based rerouting feature in a switching
system are identified by the suffix SwMinGroup.
Groups of optional rerouting objects for switching systems
are identified by the suffix SwOptGroup.
Groups of required rerouting objects for configuring and
monitoring the domain-based rerouting feature at an end system
are identified by the suffix EsMinGroup.
Groups of optional rerouting objects for end systems
are identified by the suffix EsOptGroup. |
| reroutingMIBGroups | 1.3.6.1.4.1.353.5.9.3.1.2.2 | | | |
| reroutingBaseSwMinGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.1 | | | A collection of mandatory rerouting objects which describe
the rerouting services supported in a switching
system. |
| reroutingFilterSwMinGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.2 | | | A collection of mandatory objects used for the configuration
of rerouting services in a switching system when using
filters. |
| reroutingVcSwMinGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.3 | | | A collection of mandatory per Vc rerouting objects describing
the state of the rerouting services associated to a
call in a switching system. |
| reroutingBaseSwOptionalGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.4 | | | A collection of optional rerouting object which describe
the timer configuration when hard rerouting service
is supported in a switching system. |
| reroutingFilterSwOptionalGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.5 | | | A collection of optional objects used for the configuration
of rerouting services in a switching system when using
filters. |
| reroutingVpSwOptionalGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.6 | | | A collection of optional per Vp rerouting objects describing
the state of the rerouting services associated to a
call in a switching system. |
| reroutingVcSwOptionalGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.7 | | | A collection of optional per Vc rerouting objects describing
the state of the rerouting services associated to a
call in a switching system. |
| reroutingBaseEsMinGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.8 | | | A collection of mandatory rerouting objects which describe
the rerouting services supported in an end system. |
| reroutingFilterEsMinGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.9 | | | A collection of mandatory objects used for the request
of rerouting services in this end system device when using
filters. |
| reroutingVcEsMinGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.10 | | | A collection of mandatory rerouting objects describing
the rerouting services associated to a call in an
end system device. |
| reroutingFilterEsOptionalGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.11 | | | A collection of optional objects used for the configuration
of rerouting services in this end system device when using
filters. |
| reroutingVpEsOptionalGroup | 1.3.6.1.4.1.353.5.9.3.1.2.2.12 | | | A collection of optional rerouting objects describing
the rerouting services associated to a call in an
end system device. |
