ASCEND-MIBTS-MIB

All MIBs › ASCEND-MIBTS-MIB

Category: Device Management, Vendor: Ascend/Lucent

Description: Manages terminal server port configuration and async session parameters on Ascend equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ASCEND-MIBTS-MIB?

This is a proprietary Ascend Communications MIB for terminal server port configuration and asynchronous session parameters on Ascend access equipment. It exposes per-port configuration (baud rate, flow control, session type) and status of async terminal/dial sessions. It supports monitoring hardware/software status of terminal server ports — showing whether a port is in use, idle, or in an error state — useful for tracking session activity and port health on dial-in terminal servers. It has no strong dependency on other standard MIBs beyond general conventions shared with RS-232-MIB-like port models. It is deployed on Ascend dial-in terminal servers/access concentrators used for legacy async modem pools and console/terminal access. Engineers can download the ASCEND-MIBTS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ASCEND-MIBTS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ascend dial-in terminal server/access concentrator

Monitoring Examples

No object names were captured for this module, but a terminal server MIB of this kind typically exposes a per-port table (an ascendTs*Table/Entry pattern) with port configuration and current session/connection state. An administrator would poll this table to see how many async ports are currently occupied by active sessions, with an unexpectedly high busy count indicating capacity pressure on the dial-in pool.

What Can Be Monitored

async port configuration
port session/connection status
port busy/idle state

Imported Objects

From ASCEND-MIB

configuration

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
mibtermSrvProfile	1.3.6.1.4.1.529.23.133
mibtermSrvProfileEntry	1.3.6.1.4.1.529.23.133.1.1		not-accessible	A mibtermSrvProfile entry containing objects that maps to the parameters of mibtermSrvProfile profile.
mibtermSrvProfileTable	1.3.6.1.4.1.529.23.133.1		not-accessible	A list of mibtermSrvProfile profile entries.
INT termSrvProfile_Action_o	1.3.6.1.4.1.529.23.133.1.1.84	INTEGER	read-write
INT termSrvProfile_DialoutConfiguration_DirectAccess	1.3.6.1.4.1.529.23.133.1.1.80	INTEGER	read-write	Allows direct connection to a modem by TELNETing to a configurable modem port.
INT termSrvProfile_DialoutConfiguration_Enabled	1.3.6.1.4.1.529.23.133.1.1.79	INTEGER	read-write	Allow/disallow modem outdial from the terminal server.
STR termSrvProfile_DialoutConfiguration_PasswordForDirectAccess	1.3.6.1.4.1.529.23.133.1.1.82	DisplayString	read-write	The password that must be used to gain direct access to a modem
INT termSrvProfile_DialoutConfiguration_PortForDirectAccess	1.3.6.1.4.1.529.23.133.1.1.81	INTEGER	read-write	The telnet port number for direct access to a modem.
INT termSrvProfile_DialoutConfiguration_SecurityForDirectAccess	1.3.6.1.4.1.529.23.133.1.1.83	INTEGER	read-write	The security method used to control direct modem access.
INT termSrvProfile_Enabled	1.3.6.1.4.1.529.23.133.1.1.2	INTEGER	read-write	Terminal server availability flag. When set to no all terminal server functions are disabled.
STR termSrvProfile_ImmediateModeOptions_Host	1.3.6.1.4.1.529.23.133.1.1.45	DisplayString	read-write	Name or IP address or X.121 address of the immediate TELNET, TCP, or X.25/Pad host to connect to.
INT termSrvProfile_ImmediateModeOptions_Port	1.3.6.1.4.1.529.23.133.1.1.46	INTEGER	read-write	TCP port to which the TELNET or TCP stream is to be redirected to.
INT termSrvProfile_ImmediateModeOptions_Service	1.3.6.1.4.1.529.23.133.1.1.43	INTEGER	read-write	enable/disable immediate mode and specify the service type. Immediate mode is where a user is automatically connected to a remote host using the specified service.
INT termSrvProfile_ImmediateModeOptions_TelnetHostAuth	1.3.6.1.4.1.529.23.133.1.1.44	INTEGER	read-write	Option defines if telnet is started directly bypassing the local authentication process. When enabled, authentication is the responsibility of the telnet host.
INT termSrvProfile_Index_o	1.3.6.1.4.1.529.23.133.1.1.1	INTEGER	read-only
STR termSrvProfile_MenuModeOptions_Host1	1.3.6.1.4.1.529.23.133.1.1.51	DisplayString	read-write	The address of the first host to access when terminal server menu mode is being used without remote configuration.
STR termSrvProfile_MenuModeOptions_Host2	1.3.6.1.4.1.529.23.133.1.1.56	DisplayString	read-write	The address of the second host to access when terminal server menu mode is being used without remote configuration.
STR termSrvProfile_MenuModeOptions_Host3	1.3.6.1.4.1.529.23.133.1.1.61	DisplayString	read-write	The address of the third host to access when terminal server menu mode is being used without remote configuration.
STR termSrvProfile_MenuModeOptions_Host4	1.3.6.1.4.1.529.23.133.1.1.66	DisplayString	read-write	The address of the forth host to access when terminal server menu mode is being used without remote configuration.
STR termSrvProfile_MenuModeOptions_MenuSelectionString	1.3.6.1.4.1.529.23.133.1.1.70	DisplayString	read-write	The selection string for the menu mode.
INT termSrvProfile_MenuModeOptions_Port1	1.3.6.1.4.1.529.23.133.1.1.53	INTEGER	read-write	The port for contacting host. Used only for telnet service.
INT termSrvProfile_MenuModeOptions_Port2	1.3.6.1.4.1.529.23.133.1.1.58	INTEGER	read-write	The port for contacting host. Used only for telnet service.
INT termSrvProfile_MenuModeOptions_Port3	1.3.6.1.4.1.529.23.133.1.1.63	INTEGER	read-write	The port for contacting host. Used only for telnet service.
INT termSrvProfile_MenuModeOptions_Port4	1.3.6.1.4.1.529.23.133.1.1.68	INTEGER	read-write	The port for contacting host. Used only for telnet service.
INT termSrvProfile_MenuModeOptions_RemoteConfiguration	1.3.6.1.4.1.529.23.133.1.1.49	INTEGER	read-write	When enabled, the text and host addresses that make up the menu will be retrieved from RADIUS (if RADIUS is enabled).
INT termSrvProfile_MenuModeOptions_Service1	1.3.6.1.4.1.529.23.133.1.1.52	INTEGER	read-write	Type of service required for this selection.
INT termSrvProfile_MenuModeOptions_Service2	1.3.6.1.4.1.529.23.133.1.1.57	INTEGER	read-write	Type of service required for this selection.
INT termSrvProfile_MenuModeOptions_Service3	1.3.6.1.4.1.529.23.133.1.1.62	INTEGER	read-write	Type of service required for this selection.
INT termSrvProfile_MenuModeOptions_Service4	1.3.6.1.4.1.529.23.133.1.1.67	INTEGER	read-write	Type of service required for this selection.
INT termSrvProfile_MenuModeOptions_StartWithMenus	1.3.6.1.4.1.529.23.133.1.1.47	INTEGER	read-write	Terminal server interface will start in menu mode when this field is 'yes'.
STR termSrvProfile_MenuModeOptions_Text1	1.3.6.1.4.1.529.23.133.1.1.50	DisplayString	read-write	The text to put in the terminal server menu for the first login host when remote configuration isn't available.
STR termSrvProfile_MenuModeOptions_Text2	1.3.6.1.4.1.529.23.133.1.1.55	DisplayString	read-write	The text to put in the terminal server menu for the second login host when remote configuration isn't available.
STR termSrvProfile_MenuModeOptions_Text3	1.3.6.1.4.1.529.23.133.1.1.60	DisplayString	read-write	The text to put in the terminal server menu for the third login host when remote configuration isn't available.
STR termSrvProfile_MenuModeOptions_Text4	1.3.6.1.4.1.529.23.133.1.1.65	DisplayString	read-write	The text to put in the terminal server menu for the forth login host when remote configuration isn't available.
INT termSrvProfile_MenuModeOptions_ToggleScreen	1.3.6.1.4.1.529.23.133.1.1.48	INTEGER	read-write	When enabled, users are able to toggle between menu mode and the normal terminal server command line.
STR termSrvProfile_MenuModeOptions_User1	1.3.6.1.4.1.529.23.133.1.1.54	DisplayString	read-write	The user name for this selection. Used only for rlogin service.
STR termSrvProfile_MenuModeOptions_User2	1.3.6.1.4.1.529.23.133.1.1.59	DisplayString	read-write	The user name for this selection. Used only for rlogin service.
STR termSrvProfile_MenuModeOptions_User3	1.3.6.1.4.1.529.23.133.1.1.64	DisplayString	read-write	The user name for this selection. Used only for rlogin service.
STR termSrvProfile_MenuModeOptions_User4	1.3.6.1.4.1.529.23.133.1.1.69	DisplayString	read-write	The user name for this selection. Used only for rlogin service.
INT termSrvProfile_ModemConfiguration_CellLevel	1.3.6.1.4.1.529.23.133.1.1.8	INTEGER	read-write	The modem cellular communications transmit and receive level. Valid values are -10 db .. -18 db.
INT termSrvProfile_ModemConfiguration_CellModeFirst	1.3.6.1.4.1.529.23.133.1.1.7	INTEGER	read-write	If yes, the modem attempts cellular connection first - then land connection. If no, land based is attempted first, then cellular.
INT termSrvProfile_ModemConfiguration_MaxBaudRate	1.3.6.1.4.1.529.23.133.1.1.5	INTEGER	read-write	Describes the maximum connection baud rate the modems should try.
INT termSrvProfile_ModemConfiguration_MaxV92ReceiveBaudRate	1.3.6.1.4.1.529.23.133.1.1.87	INTEGER	read-write	The maximum V.92 receive baud rate to be attempted by the modems.
INT termSrvProfile_ModemConfiguration_ModemMod	1.3.6.1.4.1.529.23.133.1.1.10	INTEGER	read-write	The modulation protocol to be attempted by the modems.
INT termSrvProfile_ModemConfiguration_ModemOnHoldTimeout	1.3.6.1.4.1.529.23.133.1.1.85	INTEGER	read-write	The allowable Modem-on-Hold timeout values.
INT termSrvProfile_ModemConfiguration_ModemTransmitLevel	1.3.6.1.4.1.529.23.133.1.1.6	INTEGER	read-write	The transmit attenuate level the modems should try.
INT termSrvProfile_ModemConfiguration_o7Even	1.3.6.1.4.1.529.23.133.1.1.9	INTEGER	read-write	If set to yes, all incoming data has its parity bit cleared and all outgoing data is forced to 7 bits with even parity.
STR termSrvProfile_ModemConfiguration_oATAnswerString	1.3.6.1.4.1.529.23.133.1.1.11	DisplayString	read-write	Allows the user to enter any additional AT commands in the modem answer string.
INT termSrvProfile_ModemConfiguration_QuickConnectEnabled	1.3.6.1.4.1.529.23.133.1.1.86	INTEGER	read-write	If set to yes, Quick-Connect will be enabled.
INT termSrvProfile_ModemConfiguration_V42_mnp	1.3.6.1.4.1.529.23.133.1.1.4	INTEGER	read-write	Describes the modem error correction mode. Error correction can be required, not used, or optional.
INT termSrvProfile_ModemConfiguration_V44Enabled	1.3.6.1.4.1.529.23.133.1.1.88	INTEGER	read-write	If set to yes, allow V.44 compression to be negotiated
INT termSrvProfile_PppModeConfiguration_Delay	1.3.6.1.4.1.529.23.133.1.1.72	INTEGER	read-write	The number of seconds to wait for PPP before putting up the login banner and converting to telnet mode.
INT termSrvProfile_PppModeConfiguration_Direct	1.3.6.1.4.1.529.23.133.1.1.73	INTEGER	read-write	Option defines if PPP negotiation is started directly after 'PPP' Term Server command is received or, not. When disabled, we wait to receive a PPP packet before sending.
INT termSrvProfile_PppModeConfiguration_Info	1.3.6.1.4.1.529.23.133.1.1.74	INTEGER	read-write	Enable/Disable the PPP/SLIP start up message.
INT termSrvProfile_PppModeConfiguration_Ppp	1.3.6.1.4.1.529.23.133.1.1.71	INTEGER	read-write	Enable/disable the PPP terminal server command.
INT termSrvProfile_SecurityMode	1.3.6.1.4.1.529.23.133.1.1.3	INTEGER	read-write	Indicates the type of terminal server security (if any).
INT termSrvProfile_SlipModeConfiguration_CslipAutoDetect	1.3.6.1.4.1.529.23.133.1.1.78	INTEGER	read-write	Enable/disbale auto detecting of SLIP header compression. This feature will try to auto-detect if the caller is using Van Jacobson header compression, and if so, the box will automatically switch to CSLIP mode.
INT termSrvProfile_SlipModeConfiguration_Info	1.3.6.1.4.1.529.23.133.1.1.77	INTEGER	read-write	Level of information displayed in SLIP start up message.
INT termSrvProfile_SlipModeConfiguration_Slip	1.3.6.1.4.1.529.23.133.1.1.75	INTEGER	read-write	Enable/disable the SLIP command from the terminal server.
INT termSrvProfile_SlipModeConfiguration_SlipBootp	1.3.6.1.4.1.529.23.133.1.1.76	INTEGER	read-write	Enable/disable the SLIP command from the terminal server.
STR termSrvProfile_TerminalModeConfiguration_Banner	1.3.6.1.4.1.529.23.133.1.1.15	DisplayString	read-write	The terminal server login banner.
INT termSrvProfile_TerminalModeConfiguration_BufferChars	1.3.6.1.4.1.529.23.133.1.1.23	INTEGER	read-write	Whether to buffer termserv characters or to forward them without buffering. Buffering provides better throughput at a slight increase in latency.
INT termSrvProfile_TerminalModeConfiguration_ClearCall	1.3.6.1.4.1.529.23.133.1.1.22	INTEGER	read-write	Select operation when a telnet/rlogin/tcp session terminates. When set to yes, the dial-in session will also terminate.
INT termSrvProfile_TerminalModeConfiguration_ClearScreen	1.3.6.1.4.1.529.23.133.1.1.13	INTEGER	read-write	Clear the screen at terminal server startup.
STR termSrvProfile_TerminalModeConfiguration_IpAddMsg	1.3.6.1.4.1.529.23.133.1.1.36	DisplayString	read-write	This is a text field that will be printed in front of the IP address in the terminal server when going into PPP.
STR termSrvProfile_TerminalModeConfiguration_IpGwAddMsg	1.3.6.1.4.1.529.23.133.1.1.39	DisplayString	read-write	This is a text field that will be printed in front of the IP Gateway address in the terminal server when going into SLIP.
STR termSrvProfile_TerminalModeConfiguration_IpNetmaskMsg	1.3.6.1.4.1.529.23.133.1.1.38	DisplayString	read-write	This is a text field that will be printed in front of the IP Netmask in the terminal server when going into SLIP.
STR termSrvProfile_TerminalModeConfiguration_LoginPrompt	1.3.6.1.4.1.529.23.133.1.1.16	DisplayString	read-write	The string used to prompt for user name when authentication is in use.
INT termSrvProfile_TerminalModeConfiguration_LoginTimeout	1.3.6.1.4.1.529.23.133.1.1.40	INTEGER	read-write	The number of seconds to wait at the login prompt for the user to login. A value of 0 disables the timeout.
INT termSrvProfile_TerminalModeConfiguration_PacketizeChars	1.3.6.1.4.1.529.23.133.1.1.42	INTEGER	read-write	The number of characters to accumulate modem data in a packet.
INT termSrvProfile_TerminalModeConfiguration_PacketizeWaitTime	1.3.6.1.4.1.529.23.133.1.1.41	INTEGER	read-write	The number of milliseconds to accumulate modem data in a packet.
STR termSrvProfile_TerminalModeConfiguration_PasswordPrompt	1.3.6.1.4.1.529.23.133.1.1.17	DisplayString	read-write	The string used to prompt for password when authentication is in use.
INT termSrvProfile_TerminalModeConfiguration_Ping	1.3.6.1.4.1.529.23.133.1.1.24	INTEGER	read-write	Enable/disable the ping command from the terminal server.
STR termSrvProfile_TerminalModeConfiguration_Prompt	1.3.6.1.4.1.529.23.133.1.1.20	DisplayString	read-write	The current terminal server prompt.
INT termSrvProfile_TerminalModeConfiguration_PromptFormat	1.3.6.1.4.1.529.23.133.1.1.37	INTEGER	read-write	TRUE if the terminal server prompt should interpret \\n.
INT termSrvProfile_TerminalModeConfiguration_RloginOptions_MaxSourcePort	1.3.6.1.4.1.529.23.133.1.1.29	INTEGER	read-write	A highest limit of the port number used by rlogin. For BSD's rlogin, the client source port range is 512 to 1023.
INT termSrvProfile_TerminalModeConfiguration_RloginOptions_MinSourcePort	1.3.6.1.4.1.529.23.133.1.1.30	INTEGER	read-write	A lowest limit of the port number used by rlogin. For BSD's rlogin, the client source port range is 512 to 1023.
INT termSrvProfile_TerminalModeConfiguration_RloginOptions_Rlogin	1.3.6.1.4.1.529.23.133.1.1.28	INTEGER	read-write	Enable/disable the rlogin command from the terminal server.
INT termSrvProfile_TerminalModeConfiguration_SilentMode	1.3.6.1.4.1.529.23.133.1.1.12	INTEGER	read-write	Don't generate any status messages upon connection.
STR termSrvProfile_TerminalModeConfiguration_SystemPassword	1.3.6.1.4.1.529.23.133.1.1.14	DisplayString	read-write	Global terminal server system access password.
INT termSrvProfile_TerminalModeConfiguration_Tcp	1.3.6.1.4.1.529.23.133.1.1.26	INTEGER	read-write	Enable/disable the tcp command from the terminal server.
INT termSrvProfile_TerminalModeConfiguration_TelnetOptions_AutoTelnet	1.3.6.1.4.1.529.23.133.1.1.33	INTEGER	read-write	If set to 'yes' unknown terminal server commands will be treated as the name of a host to telnet to.
INT termSrvProfile_TerminalModeConfiguration_TelnetOptions_LocalEcho	1.3.6.1.4.1.529.23.133.1.1.34	INTEGER	read-write	Defines the default echo mode for telnet sessions. The default mode can be overridded on the command line.
INT termSrvProfile_TerminalModeConfiguration_TelnetOptions_Security	1.3.6.1.4.1.529.23.133.1.1.35	INTEGER	read-write	Level of security used to authenticate telnet sessions.
INT termSrvProfile_TerminalModeConfiguration_TelnetOptions_Telnet	1.3.6.1.4.1.529.23.133.1.1.31	INTEGER	read-write	Enable/disable the use of the telnet terminal server command.
INT termSrvProfile_TerminalModeConfiguration_TelnetOptions_TelnetMode	1.3.6.1.4.1.529.23.133.1.1.32	INTEGER	read-write	Selects default Telnet mode: ASCII, Binary, or Transparent.
STR termSrvProfile_TerminalModeConfiguration_TerminalType	1.3.6.1.4.1.529.23.133.1.1.21	DisplayString	read-write	The default terminal type for telnet and rlogin sessions.
STR termSrvProfile_TerminalModeConfiguration_ThirdLoginPrompt	1.3.6.1.4.1.529.23.133.1.1.18	DisplayString	read-write	An optional third prompt for a terminal server login. If this value is null no third prompt is used.
INT termSrvProfile_TerminalModeConfiguration_ThirdPromptSequence	1.3.6.1.4.1.529.23.133.1.1.19	INTEGER	read-write	Select where the third prompt should appear in the login sequence: either before or after user name & password.
INT termSrvProfile_TerminalModeConfiguration_Traceroute	1.3.6.1.4.1.529.23.133.1.1.25	INTEGER	read-write	Enable/disable the traceroute command from the terminal server.
INT termSrvProfile_TerminalModeConfiguration_TsAraEnabled	1.3.6.1.4.1.529.23.133.1.1.27	INTEGER	read-write	TRUE if terminal server users are allowed to intiate async ARA sessions.

RFC description

Vendor-private Ascend/Lucent MIB for terminal server and access equipment management.

Start monitoring Ascend Communications (Lucent) MAX/Pipeline/TNT WAN access equipment (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ASCEND-MIBTS-MIB

What Is ASCEND-MIBTS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description