ASCEND-MIBATMIF-MIB

All MIBs › ASCEND-MIBATMIF-MIB

Category: ATM, Vendor: Ascend/Lucent

Description: Manages ATM interface configuration and performance counters on Ascend ATM-capable equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ASCEND-MIBATMIF-MIB?

ASCEND-MIBATMIF-MIB is a proprietary Ascend Communications module that manages ATM interface configuration and performance data on Ascend's ATM-capable equipment, such as the APX/GRF switches and MAX units with ATM uplinks. It exposes interface-level configuration (VPI/VCI ranges, interface types) alongside performance counters covering cell throughput, errors, and interface status. For hardware/software monitoring it is chiefly useful for tracking interface operational (up/down) state and cell-level error or discard counts, which reveal physical-layer or framing problems on an ATM link before they escalate to service outages. It parallels, but does not directly extend, the IETF ATM-MIB (RFC 2515) family, reimplementing similar concepts under Ascend's own object tree. It is typically deployed on WAN edge or core equipment carrying ATM-encapsulated traffic in carrier and enterprise networks, where the ASCEND-MIBATMIF-MIB MIB is polled to confirm ATM interface health.

IPNetwork Monitor allows you to monitor SNMP objects defined in ASCEND-MIBATMIF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ascend APX/GRF ATM switch
Ascend MAX with ATM uplink

Monitoring Examples

sample_objects was empty for this module, so no specific table names can be cited; the description below reflects the module's declared scope. An operator would poll ATM interface entries to check operational status and cumulative cell error/loss counts, flagging a link as degraded if error counts climb while cell throughput drops. This kind of polling is typically paired with ATM port-level MIBs from the same vendor for a full picture of link health.

What Can Be Monitored

ATM interface operational status
cell error/loss counts
ATM interface configuration (VPI/VCI ranges)
interface cell throughput

Imported Objects

From ASCEND-MIB

configuration

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT atmInterfaceProfile_Action_o	1.3.6.1.4.1.529.23.40.1.1.57	INTEGER	read-write
INT atmInterfaceProfile_InterfaceAddress_LogicalItem	1.3.6.1.4.1.529.23.40.1.1.8	INTEGER	read-write	A number that specifies an addressable logical entity within the context of a physical address.
INT atmInterfaceProfile_InterfaceAddress_PhysicalAddress_ItemNumber	1.3.6.1.4.1.529.23.40.1.1.7	INTEGER	read-write	A number that specifies an addressable entity within the context of shelf and slot.
INT atmInterfaceProfile_InterfaceAddress_PhysicalAddress_Shelf	1.3.6.1.4.1.529.23.40.1.1.5	INTEGER	read-write	The number of the shelf that the addressed physical device resides on.
INT atmInterfaceProfile_InterfaceAddress_PhysicalAddress_Slot	1.3.6.1.4.1.529.23.40.1.1.6	INTEGER	read-write	The number of the slot that the addressed physical device resides on.
INT atmInterfaceProfile_Item_o	1.3.6.1.4.1.529.23.40.1.1.3	INTEGER	read-only
INT atmInterfaceProfile_LogicalItem_o	1.3.6.1.4.1.529.23.40.1.1.4	INTEGER	read-only
STR atmInterfaceProfile_Name	1.3.6.1.4.1.529.23.40.1.1.9	DisplayString	read-write	Name of ATM Interface.
INT atmInterfaceProfile_Shelf_o	1.3.6.1.4.1.529.23.40.1.1.1	INTEGER	read-only
INT atmInterfaceProfile_Slot_o	1.3.6.1.4.1.529.23.40.1.1.2	INTEGER	read-only
STR atmInterfaceProfile_SvcOptions_AtmAddress_AesaAddress_DspPortion_Esi	1.3.6.1.4.1.529.23.40.1.1.18	DisplayString	read-write	An End System Identifier (ESI) which uniquely identifies the end system within the specified subnetwork.
STR atmInterfaceProfile_SvcOptions_AtmAddress_AesaAddress_DspPortion_HoDsp	1.3.6.1.4.1.529.23.40.1.1.17	DisplayString	read-write	A High-Order Domain-Specific Part of AESA address. The IDP portion determine the format of the HO-DSP.
STR atmInterfaceProfile_SvcOptions_AtmAddress_AesaAddress_DspPortion_Sel	1.3.6.1.4.1.529.23.40.1.1.19	DisplayString	read-write	A selector (SEL) field that may be used by the end system.
INT atmInterfaceProfile_SvcOptions_AtmAddress_AesaAddress_Format	1.3.6.1.4.1.529.23.40.1.1.14	INTEGER	read-write	An AESA address format used to define this SVC address.
STR atmInterfaceProfile_SvcOptions_AtmAddress_AesaAddress_IdpPortion_Afi	1.3.6.1.4.1.529.23.40.1.1.15	DisplayString	read-write	An Authority and Format Identifier(AFI) for AESA address. Must be defined for every AESA address.
STR atmInterfaceProfile_SvcOptions_AtmAddress_AesaAddress_IdpPortion_Idi	1.3.6.1.4.1.529.23.40.1.1.16	DisplayString	read-write	An Initial Domain Identifier (IDI) portion of the AESA address.
STR atmInterfaceProfile_SvcOptions_AtmAddress_E164NativeAddress	1.3.6.1.4.1.529.23.40.1.1.13	DisplayString	read-write	An SVC address in a native E.164 format.
INT atmInterfaceProfile_SvcOptions_AtmAddress_NumberingPlan	1.3.6.1.4.1.529.23.40.1.1.12	INTEGER	read-write	Numbering plan for an SVC address
INT atmInterfaceProfile_SvcOptions_AtmProtocol	1.3.6.1.4.1.529.23.40.1.1.11	INTEGER	read-write	ATM protocol on this link.
INT atmInterfaceProfile_SvcOptions_Enabled	1.3.6.1.4.1.529.23.40.1.1.10	INTEGER	read-write	SVC signalling (Q.93b) is enabled on this link.
INT atmInterfaceProfile_SvcOptions_InsertCallingPartyAddr	1.3.6.1.4.1.529.23.40.1.1.20	INTEGER	read-write	Insert ATM address of this interface in calling party address IE during call setup.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_AssignVpiVci	1.3.6.1.4.1.529.23.40.1.1.44	INTEGER	read-write	In the case of UNI4.0 and PNNI this parameter specifies who assigns the VPI/VCI. TRUE will allow the local stack and FALSE will let the partner stack to assign.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_MaxRestart	1.3.6.1.4.1.529.23.40.1.1.21	INTEGER	read-write	Maximum number of unacknowledged tx RESTART.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_MaxStatenq	1.3.6.1.4.1.529.23.40.1.1.22	INTEGER	read-write	Maximum number of unacknowledged tx STATUS ENQ.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_SaalRetryMs	1.3.6.1.4.1.529.23.40.1.1.38	INTEGER	read-write	Timer value for retrying AAL_ESTABLISH messages.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T301Ms	1.3.6.1.4.1.529.23.40.1.1.23	INTEGER	read-write	Timer (in msec) for alerting supervision function. This timer is started on receipt of ALERT in Call received/delivered state and stopped when CONNECT is received.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T303Ms	1.3.6.1.4.1.529.23.40.1.1.24	INTEGER	read-write	Timer (in msec) for a response after SETUP is sent. This timer is stopped when the CONNECT, CALL PROCEEDING, or RELEASE COMPLETE is received.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T303NumReties	1.3.6.1.4.1.529.23.40.1.1.39	INTEGER	read-write	Number of times SETUP could be resent in case of T303 timer expiry.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T306Ms	1.3.6.1.4.1.529.23.40.1.1.25	INTEGER	read-write	Timer (in msec) for a RELEASE_COMPLETE to be received after a release has been sent.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T308Ms	1.3.6.1.4.1.529.23.40.1.1.26	INTEGER	read-write	Timer (in msec) for a response after RELEASE is sent. This is a release indication timer. This timer is started when the RELEASE message is sent and normally is stopped when the RELEASE or RELEASE COMPLETE is received.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T308NumRetries	1.3.6.1.4.1.529.23.40.1.1.40	INTEGER	read-write	Number of times RELEASE could be sent in case of T308 timer expiry.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T309Ms	1.3.6.1.4.1.529.23.40.1.1.27	INTEGER	read-write	Timer (in msec) for Q.SAAL to reconnect. After this time, calls are dropped. When set to 0, a default value based on an ATM signaling protocol will be used.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T310Ms	1.3.6.1.4.1.529.23.40.1.1.28	INTEGER	read-write	Timer (in msec) for a response after SETUP is received. Also called the CALL PROCEEDING timer.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T313Ms	1.3.6.1.4.1.529.23.40.1.1.29	INTEGER	read-write	Timer (in msec) for a response after CONNECT is sent. Also called the connect request timer. It is started when the CONNECT is sent and stopped when the CONNECT ACKNOWLEDGE is recieved.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T316Ms	1.3.6.1.4.1.529.23.40.1.1.30	INTEGER	read-write	Timer (in msec) for a response after RESTART is sent. Also called the restart request timer. It is started when the RESTART is sent and stopped when the RESTART ACKNOWLEDGE is recieved.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T316NumRetries	1.3.6.1.4.1.529.23.40.1.1.41	INTEGER	read-write	Number of times RESTART could be sent in case RESTART ACK is not received withinn T316 timer expiry.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T317Ms	1.3.6.1.4.1.529.23.40.1.1.31	INTEGER	read-write	Timer (in msec) for internal clearing of call references. This timer is started as a result of a restart and cleared when all the internal call references are cleared. Should be less than the the likely value of T316 of the peer.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T322Ms	1.3.6.1.4.1.529.23.40.1.1.32	INTEGER	read-write	Timer (in msec) for a response after STATUS ENQ is sent.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T322NumRetries	1.3.6.1.4.1.529.23.40.1.1.42	INTEGER	read-write	Number of times STAT ENQ could be sent before a response is received within the T322 timer expiry.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T331Ms	1.3.6.1.4.1.529.23.40.1.1.33	INTEGER	read-write	Timer (in msec) for internal clearing of call references.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T331NumRetries	1.3.6.1.4.1.529.23.40.1.1.43	INTEGER	read-write
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T333Ms	1.3.6.1.4.1.529.23.40.1.1.34	INTEGER	read-write	Timer (in msec) for internal clearing of call references.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T397Ms	1.3.6.1.4.1.529.23.40.1.1.35	INTEGER	read-write	Timer (in msec) for internal clearing of call references.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T398Ms	1.3.6.1.4.1.529.23.40.1.1.36	INTEGER	read-write	Timer (in msec) for receipt of a response to a DROP PARTY that was sent.
INT atmInterfaceProfile_SvcOptions_Q93bOptions_T399Ms	1.3.6.1.4.1.529.23.40.1.1.37	INTEGER	read-write	Timer (in msec) for receipt of a response to an ADD PARTY that was sent.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_MaxCc	1.3.6.1.4.1.529.23.40.1.1.46	INTEGER	read-write	Maximum number of control PDU (BGN, END, RESYNC) retransmissions.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_MaxPd	1.3.6.1.4.1.529.23.40.1.1.47	INTEGER	read-write	Maximum number of Sequenced data PDU's between poll.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_MaxStat	1.3.6.1.4.1.529.23.40.1.1.48	INTEGER	read-write	Maximum length of STAT PDU.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_PollAfterRetransmission	1.3.6.1.4.1.529.23.40.1.1.54	INTEGER	read-write	Specifies after retransmitting PDUs whether a POLL must be sent before sending any further PDUs.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_RepeatUstat	1.3.6.1.4.1.529.23.40.1.1.55	INTEGER	read-write	Specifies whether two USTAT messages should be sent each time it is required to be sent.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_TccMs	1.3.6.1.4.1.529.23.40.1.1.49	INTEGER	read-write	Retry time (in msec) for control PDU's(BGN, END, RESYNC).
INT atmInterfaceProfile_SvcOptions_QsaalOptions_TidleMs	1.3.6.1.4.1.529.23.40.1.1.53	INTEGER	read-write	Poll sent (in msec) when idle -- UNI 3.1, only.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_TkeepaliveMs	1.3.6.1.4.1.529.23.40.1.1.51	INTEGER	read-write	Poll sent (in msec) when in transient state. When set to 0, a default value based on an ATM signaling protocol will be used.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_TnoresponseMs	1.3.6.1.4.1.529.23.40.1.1.52	INTEGER	read-write	STAT received at least this period(in msec). When set to 0, a default value based on an ATM signaling protocol will be used.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_TpollMs	1.3.6.1.4.1.529.23.40.1.1.50	INTEGER	read-write	Poll sent (in msec) when active. When set to 0, a default value based on an ATM signaling protocol will be used.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_UstatRspToPoll	1.3.6.1.4.1.529.23.40.1.1.56	INTEGER	read-write	Specifies whether a USTAT should be sent in response to a POLL indicating an out of sequence PDU.
INT atmInterfaceProfile_SvcOptions_QsaalOptions_WindowSize	1.3.6.1.4.1.529.23.40.1.1.45	INTEGER	read-write	Q.SAAL window size
mibatmInterfaceProfile	1.3.6.1.4.1.529.23.40
mibatmInterfaceProfileEntry	1.3.6.1.4.1.529.23.40.1.1		not-accessible	A mibatmInterfaceProfile entry containing objects that maps to the parameters of mibatmInterfaceProfile profile.
mibatmInterfaceProfileTable	1.3.6.1.4.1.529.23.40.1		not-accessible	A list of mibatmInterfaceProfile profile entries.

RFC description

Ascend Communications vendor MIB for ATM interface management and configuration on access devices.

Start monitoring Ascend Communications (Lucent) ATM switching equipment (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ASCEND-MIBATMIF-MIB

What Is ASCEND-MIBATMIF-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description