All MIBs › ASANTE-HUB1012-MIB
Category: Network Interfaces
Description: Provides SNMP management of Asante HUB1012 Ethernet repeater ports and statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ASANTE-HUB1012-MIB?
ASANTE-HUB1012-MIB is a vendor-specific legacy MIB from Asante Technologies for the HUB1012, an Ethernet repeater/hub device, providing SNMP management of its repeater ports and per-port traffic statistics. It is intended to expose port-level configuration (enable/disable, partition state) and counters such as collisions, errors, and packet counts typical of repeater-class devices from the era of shared Ethernet hubs. Its monitoring value is primarily hardware/port status: detecting a partitioned (auto-disabled) port due to excessive collisions or a jabbering NIC, and tracking per-port traffic/error counters to spot a failing cable segment or misbehaving attached device. It follows the general model of the IETF Repeater MIB (RFC 1516) conventions common to hub-class devices of its generation. It was deployed in legacy shared-Ethernet LAN environments using Asante hub hardware, where ASANTE-HUB1012-MIB SNMP monitoring tracked port health, now largely superseded by switched Ethernet.
IPNetwork Monitor allows you to monitor SNMP objects defined in ASANTE-HUB1012-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Asante HUB1012 Ethernet repeater/hub
Monitoring Examples
No sample objects were provided for this legacy module. Based on its stated purpose as a hub/repeater MIB, an administrator would typically poll per-port statistics to identify a port that has auto-partitioned itself off the shared segment due to excessive collisions, which would explain a device suddenly losing connectivity through the hub. Per-port error and collision counters would also be trended to spot a degrading cable or NIC on the shared LAN segment.
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| NetworkAddress | |
| TimeTicks | |
| enterprises | |
| private |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| adaptCard | 1.3.6.1.4.1.298.1.2 | |||
| adapterProductId | 1.3.6.1.4.1.298.2.1 | |||
| agentFw | 1.3.6.1.4.1.298.1.1.2 | |||
| INT agentFwMajorVer | 1.3.6.1.4.1.298.1.1.2.1 | INTEGER | read-only | The major firmware version number of the agent prom code. |
| INT agentFwMinorVer | 1.3.6.1.4.1.298.1.1.2.2 | INTEGER | read-only | The minor firmware version number of the agent prom code. |
| agentHw | 1.3.6.1.4.1.298.1.1.3 | |||
| INT agentHwReVer | 1.3.6.1.4.1.298.1.1.3.1 | INTEGER | read-only | The hardware reversion number of the network management module. |
| INT agentHwVer | 1.3.6.1.4.1.298.1.1.3.2 | INTEGER | read-only | The hardware model number of the network management module |
| INT agentImageLoadMode | 1.3.6.1.4.1.298.1.1.1.3 | INTEGER | read-write | Tells hub whether the software image is to be loaded from the FLASH EPROM or from over the network. |
| agentNetProtocol | 1.3.6.1.4.1.298.1.1.5 | |||
| OCT agentNetProtoStkCapMap | 1.3.6.1.4.1.298.1.1.4 | OCTET STRING | read-only | This octet string represents the current protocol stack configuration supported by the agent, encoded as a bit string. Each protocol stack is represented by a single bit. When the value of a bit = 1, it indicates that the protocol stack on the agent represented by that bit is supported; when zero, the protocol stack is not supported. The number of octets in the string is always integer multiple of the octet. The first protocol stack will encode in the least significant bit of the first octet. Current, only IP Stack(bit 0) and IPX Stack(bit 1) were defined, all other bits should be zero. |
| INT agentOutBandBaudRate | 1.3.6.1.4.1.298.1.1.1.8 | INTEGER | read-write | The baud rate setting for the out-of-band port. |
| OCT agentOutBandDialString | 1.3.6.1.4.1.298.1.1.1.7 | OCTET STRING | read-write | This is the initialization string used by the Network Management station to establish the out-of-band connection for modem only. |
| OCT agentRemoteBootFile | 1.3.6.1.4.1.298.1.1.1.6 | OCTET STRING | read-write | The boot file name that is sent to the boot file server by agent boot code during boot time. |
| INT agentRemoteBootInfo | 1.3.6.1.4.1.298.1.1.1.4 | INTEGER | read-only | The method for getting boot parameter information. |
| INT agentRemoteBootProtocol | 1.3.6.1.4.1.298.1.1.1.5 | INTEGER | read-write | The netboot protocol that used to load the agent software. |
| INT agentReset | 1.3.6.1.4.1.298.1.1.1.9 | INTEGER | read-write | The object to allow software to perform 'push_button' system reset. |
| INT agentRunTimeImageMajorVer | 1.3.6.1.4.1.298.1.1.1.1 | INTEGER | read-only | The major software version number of the agent run time image. |
| INT agentRunTimeImageMinorVer | 1.3.6.1.4.1.298.1.1.1.2 | INTEGER | read-only | The minor software version number of the agent run time image. |
| agentSw | 1.3.6.1.4.1.298.1.1.1 | |||
| asante | 1.3.6.1.4.1.298 | |||
| concAlarmMgt | 1.3.6.1.4.1.298.1.3.6 | |||
| concBasicGrp | 1.3.6.1.4.1.298.1.3.1.1 | |||
| concChassis | 1.3.6.1.4.1.298.1.3.1 | |||
| INT concChassisBkplRev | 1.3.6.1.4.1.298.1.3.1.1.3 | INTEGER | read-only | The concentrator's chassis backplane revision number. |
| INT concChassisBkplType | 1.3.6.1.4.1.298.1.3.1.1.2 | INTEGER | read-only | The concentrator's chassis backplane type. |
| INT concChassisFanStatus | 1.3.6.1.4.1.298.1.3.1.1.5 | INTEGER | read-only | The value of this object identifies the fan status. |
| INT concChassisGroupCapacity | 1.3.6.1.4.1.298.1.3.1.1.6 | INTEGER | read-only | The number of groups that can be contained within the concentrator. |
| OCT concChassisGroupMap | 1.3.6.1.4.1.298.1.3.1.1.7 | OCTET STRING | read-only | This octet string represents the current configuration of groups, encoded as a bit string, each group is represented by a single bit. |
| STR concChassisGrpDescr | 1.3.6.1.4.1.298.1.3.1.1.8.1.4 | DisplayString | read-only | A description of this group device. |
| concChassisGrpEntry | 1.3.6.1.4.1.298.1.3.1.1.8.1 | not-accessible | A list of information for each slot in this chassis. | |
| INT concChassisGrpHwRev | 1.3.6.1.4.1.298.1.3.1.1.8.1.5 | INTEGER | read-only | The hardware revision number of this particular group. |
| INT concChassisGrpIndex | 1.3.6.1.4.1.298.1.3.1.1.8.1.1 | INTEGER | read-only | The value of this object identifies the chassis group table for which this entry contains group related information. |
| INT concChassisGrpNumberPort | 1.3.6.1.4.1.298.1.3.1.1.8.1.2 | INTEGER | read-only | The number of port is available for up/down link within this group. |
| concChassisGrpTable | 1.3.6.1.4.1.298.1.3.1.1.8 | not-accessible | A table that contains information about the group/slot in this chassis. | |
| INT concChassisGrpType | 1.3.6.1.4.1.298.1.3.1.1.8.1.3 | INTEGER | read-only | The value represents the function of this group. |
| concChassisPsEntry | 1.3.6.1.4.1.298.1.3.1.1.4.1 | not-accessible | The entry in the table containing the information about a single power supply. | |
| INT concChassisPsIndex | 1.3.6.1.4.1.298.1.3.1.1.4.1.1 | INTEGER | read-only | The value of this object identifies the power supply table for which this entry contains power supply type and status. |
| INT concChassisPsModuleType | 1.3.6.1.4.1.298.1.3.1.1.4.1.2 | INTEGER | read-only | The value of this object identifies the power supply module type. |
| INT concChassisPsStatus | 1.3.6.1.4.1.298.1.3.1.1.4.1.3 | INTEGER | read-only | The value of this object identifies the power supply module status. |
| concChassisPsTable | 1.3.6.1.4.1.298.1.3.1.1.4 | not-accessible | This table contains concentrator's power supply information. | |
| INT concChassisType | 1.3.6.1.4.1.298.1.3.1.1.1 | INTEGER | read-only | The concentrator's chassis type. |
| concConfiguration | 1.3.6.1.4.1.298.1.3.2 | |||
| concentrator | 1.3.6.1.4.1.298.1.3 | |||
| concNodeMgt | 1.3.6.1.4.1.298.1.3.5 | |||
| concProductId | 1.3.6.1.4.1.298.2.2 | |||
| concStateCtrl | 1.3.6.1.4.1.298.1.3.4 | |||
| concStatistics | 1.3.6.1.4.1.298.1.3.3 | |||
| INT eColGraphBar | 1.3.6.1.4.1.298.1.3.3.1.6.1.1 | INTEGER | read-only | Information on hardware LED collision graph bar. |
| CTR eGlobalHubAlignmentErrors | 1.3.6.1.4.1.298.1.3.3.1.1.6 | Counter | read-only | Global counter, for this hub, of frames which are not integer multiples of 1 byte. |
| CTR eGlobalHubAutoPartitions | 1.3.6.1.4.1.298.1.3.3.1.1.15 | Counter | read-only | Global counter, for this hub, of all ports including 3in1 port being partitioned from network in response to 31 or more continuous collisions. |
| CTR eGlobalHubBadFrames | 1.3.6.1.4.1.298.1.3.3.1.1.17 | Counter | read-only | Global counter, for this hub, of total errored frame including toolong, runts, misaligned, or bad FCS. |
| CTR eGlobalHubBcastFrames | 1.3.6.1.4.1.298.1.3.3.1.1.3 | Counter | read-only | Global counter of number of broadcast frames for his hub. All 1s in network destination address. Multicast packets are not included. |
| CTR eGlobalHubCollisions | 1.3.6.1.4.1.298.1.3.3.1.1.12 | Counter | read-only | Global counter of collision flags, for this hub. |
| CTR eGlobalHubDataRateMismatch | 1.3.6.1.4.1.298.1.3.3.1.1.10 | Counter | read-only | Global counter, for this hub, of errors where incoming data rate is not with in the tolerance level of 10MHZ + or - 0.01%. |
| CTR eGlobalHubFCSErrors | 1.3.6.1.4.1.298.1.3.3.1.1.8 | Counter | read-only | Global counter, for this hub, of frames that failed Cyclic Redundancy Check (CRC). |
| CTR eGlobalHubFragmentErrors | 1.3.6.1.4.1.298.1.3.3.1.1.7 | Counter | read-only | Global counter, for this hub, of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error). |
| CTR eGlobalHubFrameTooLongs | 1.3.6.1.4.1.298.1.3.3.1.1.4 | Counter | read-only | Global counter, for this hub, of data frames longer than 1518 bytes, with a SFD and good FCS. |
| CTR eGlobalHubIFGErrors | 1.3.6.1.4.1.298.1.3.3.1.1.9 | Counter | read-only | Global counter, for this hub, of occurrences of Interframe Gap Errors where time period between data frames is less than 5.5 micro seconds. |
| CTR eGlobalHubLateCollisions | 1.3.6.1.4.1.298.1.3.3.1.1.13 | Counter | read-only | Global counter, for this hub, of collisions occurring after the 64 byte collision window. |
| CTR eGlobalHubMcastFrames | 1.3.6.1.4.1.298.1.3.3.1.1.2 | Counter | read-only | Global counter of number of multicast frames for this hub. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included. |
| CTR eGlobalHubMJLPs | 1.3.6.1.4.1.298.1.3.3.1.1.14 | Counter | read-only | Global counter of MAU jabber lockup protection where hub repeater chip goes into lockup state. |
| CTR eGlobalHubReadableFrames | 1.3.6.1.4.1.298.1.3.3.1.1.1 | Counter | read-only | Global counter of good or readable frames for this hub. Frame is between 64 and 1518 bytes in length and has SFD and good FCS. |
| CTR eGlobalHubRunts | 1.3.6.1.4.1.298.1.3.3.1.1.5 | Counter | read-only | Global counter, for this hub, of data frames with size less than 64 bytes, with no CRC or alignment errors. |
| CTR eGlobalHubSFDMissing | 1.3.6.1.4.1.298.1.3.3.1.1.16 | Counter | read-only | Global counter, for this hub, of a burst of data greater than or equal to 10 bytes in length with no SFD. |
| CTR eGlobalHubShortEvents | 1.3.6.1.4.1.298.1.3.3.1.1.11 | Counter | read-only | Global counter, for this hub, of data burst where data is less than 10 bytes in length, with no SFD. |
| eGlobalStatistics | 1.3.6.1.4.1.298.1.3.3.1.1 | |||
| CTR eGrpStatAlignmentErrors | 1.3.6.1.4.1.298.1.3.3.1.3.1.7 | Counter | read-only | Group counter of frames which are not integer multiples of 1 byte . |
| CTR eGrpStatAutoPartitions | 1.3.6.1.4.1.298.1.3.3.1.3.1.16 | Counter | read-only | Group counter of ports in group autopartitioned in response to 31 or more continuous collisions. |
| CTR eGrpStatBadFrames | 1.3.6.1.4.1.298.1.3.3.1.3.1.18 | Counter | read-only | Group counter of total errored frames including toolong, runts, misaligned, or bad FCS. |
| CTR eGrpStatBcastFrames | 1.3.6.1.4.1.298.1.3.3.1.3.1.4 | Counter | read-only | Group counter of number of broadcast frames. All 1s in network destination address. Multicast packets are not included. |
| CTR eGrpStatCollisions | 1.3.6.1.4.1.298.1.3.3.1.3.1.13 | Counter | read-only | Group counter of collision flags. |
| CTR eGrpStatDataRateMismatch | 1.3.6.1.4.1.298.1.3.3.1.3.1.11 | Counter | read-only | Group counter of errors where incoming data rate is not with in the tolerance level of 10 MHZ + or - 0.01%. |
| CTR eGrpStatFCSErrors | 1.3.6.1.4.1.298.1.3.3.1.3.1.9 | Counter | read-only | Group counter frames that failed Cyclic Redundancy Check (CRC). |
| CTR eGrpStatFragmentErrors | 1.3.6.1.4.1.298.1.3.3.1.3.1.8 | Counter | read-only | Group counter of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error). |
| CTR eGrpStatFrameTooLongs | 1.3.6.1.4.1.298.1.3.3.1.3.1.5 | Counter | read-only | Group counter for data frames longer than 1518 bytes, with a SFD and good FCS. |
| CTR eGrpStatIFGErrors | 1.3.6.1.4.1.298.1.3.3.1.3.1.10 | Counter | read-only | Group counter of Interframe Gap Errors where time period between data frames is less than 5.5 micro seconds. |
| INT eGrpStatIndex | 1.3.6.1.4.1.298.1.3.3.1.3.1.1 | INTEGER | read-only | The value of this object identifies the group for which this entry contains group statistical information. |
| eGrpStatisticsEntry | 1.3.6.1.4.1.298.1.3.3.1.3.1 | not-accessible | Entry for individual group in table. | |
| eGrpStatisticsTable | 1.3.6.1.4.1.298.1.3.3.1.3 | not-accessible | Table of statistical information for each group. | |
| CTR eGrpStatLateCollisions | 1.3.6.1.4.1.298.1.3.3.1.3.1.14 | Counter | read-only | Group counter of collisions occurring after the 64 byte collision window. |
| CTR eGrpStatMcastFrames | 1.3.6.1.4.1.298.1.3.3.1.3.1.3 | Counter | read-only | Group counter of number of muliticast frames. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included. |
| CTR eGrpStatMJLPs | 1.3.6.1.4.1.298.1.3.3.1.3.1.15 | Counter | read-only | Group counter of MAU jabber lockup protection where hub repeater chip goes into lockup state. |
| CTR eGrpStatReadableFrames | 1.3.6.1.4.1.298.1.3.3.1.3.1.2 | Counter | read-only | Group counter of 'good' or readable frames. Frame is between 64 and 1518 bytes in length and has SFD and good FCS. |
| CTR eGrpStatRunts | 1.3.6.1.4.1.298.1.3.3.1.3.1.6 | Counter | read-only | Group counter for data frames with size less than 64 bytes, with no CRC or alignment errors. |
| CTR eGrpStatSFDMissing | 1.3.6.1.4.1.298.1.3.3.1.3.1.17 | Counter | read-only | Group counter of a burst of data greater than or equal to 10 bytes in length with no SFD. |
| CTR eGrpStatShortEvents | 1.3.6.1.4.1.298.1.3.3.1.3.1.12 | Counter | read-only | Group counter of data burst where data is less than 10 bytes in length, with no SFD. |
| INT ePortGrpIndex | 1.3.6.1.4.1.298.1.3.3.1.4.1.1 | INTEGER | read-only | The value of this object identifies the group for which this entry contains port statistical information. |
| INT ePortIndex | 1.3.6.1.4.1.298.1.3.3.1.4.1.2 | INTEGER | read-only | The value of this object identifies the port for which this entry contains port statistical information. |
| INT ePortRateAlignmentErrors | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.8 | INTEGER | read-only | Rate of occurrence of frames which are not integer multiples of 1 byte. |
| INT ePortRateAutoPartitions | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.17 | INTEGER | read-only | Rate of occurrence of times port was autopartitioned in response to 31 or more continuous collisions. |
| INT ePortRateBadFrames | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.19 | INTEGER | read-only | Rate of occurrence of total errored frames including toolong, runts, misaligned, or bad FCS. |
| INT ePortRateBcastFrames | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.5 | INTEGER | read-only | Rate of occurrence of number of broadcast frames. All 1s in network destination address. Multicast packets are not included. |
| INT ePortRateCollisions | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.14 | INTEGER | read-only | Rate of occurrence of collision flags. |
| INT ePortRateDataRateMismatch | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.12 | INTEGER | read-only | Rate of occurrence of errors where incoming data rate is not with in the tolerance level of 10 MHz + or - 0.01%. |
| ePortRateEntry | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1 | not-accessible | Individual entry in port rate table. | |
| INT ePortRateFCSErrors | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.10 | INTEGER | read-only | Rate of occurrence of frames that failed Cyclic Redundancy Check (CRC). |
| INT ePortRateFragmentErrors | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.9 | INTEGER | read-only | Rate of occurrence of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error). |
| INT ePortRateFrameTooLongs | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.6 | INTEGER | read-only | Rate of occurrence of data frames longer than 1518 bytes, with a SFD and good FCS. |
| INT ePortRateGrpIndex | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.1 | INTEGER | read-only | The value of this object identifies the group for which this entry contains port statistical information. |
| INT ePortRateIFGErrors | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.11 | INTEGER | read-only | Rate of occurrence of interframe Gap Errors where time period between data frames is less than 5.5 micro seconds. |
| INT ePortRateLateCollisions | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.15 | INTEGER | read-only | Rate of occurrence of collisions occurring after the 64 byte collision window. |
| INT ePortRateMcastFrames | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.4 | INTEGER | read-only | Rate of occurrence of number of muliticast frames. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included. |
| INT ePortRateMJLPs | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.16 | INTEGER | read-only | Rate of occurrence of MAU jabber lockup protection where hub repeater chip goes into lockup state. |
| INT ePortRatePortIndex | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.2 | INTEGER | read-only | This value identifies the port for which this entry contains port statistical information. |
| INT ePortRateReadableFrames | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.3 | INTEGER | read-only | Rate of occurrence of good or readable frames. |
| INT ePortRateRunts | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.7 | INTEGER | read-only | Rate of occurrence of data frames with size less than 64 bytes, with no CRC or alignment errors. |
| INT ePortRateSFDMissing | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.18 | INTEGER | read-only | Rate of occurrence of a burst of data greater than or equal to 10 bytes in length with no SFD. |
| INT ePortRateShortEvents | 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.13 | INTEGER | read-only | Rate of occurrence of data burst where data is less than 10 bytes in length, with no SFD. |
| ePortRateTable | 1.3.6.1.4.1.298.1.3.3.1.6.1.6 | not-accessible | Network statistics for individual ports measured in Rate/Second. | |
| CTR ePortStatAlignmentErrors | 1.3.6.1.4.1.298.1.3.3.1.4.1.8 | Counter | read-only | Port counter of frames which are not integer multiples of 1 byte. |
| CTR ePortStatAutoPartitions | 1.3.6.1.4.1.298.1.3.3.1.4.1.17 | Counter | read-only | Port counter of number of times port was autopartitioned in response to 31 or more continuous collisions. |
| CTR ePortStatBadFrames | 1.3.6.1.4.1.298.1.3.3.1.4.1.19 | Counter | read-only | Port counter of total errored frames including toolong, runts, misaligned, or bad FCS. |
| CTR ePortStatBcastFrames | 1.3.6.1.4.1.298.1.3.3.1.4.1.5 | Counter | read-only | Port counter of number of broadcast frames. All 1s in network destination address. Multicast packets are not included. |
| CTR ePortStatCollisions | 1.3.6.1.4.1.298.1.3.3.1.4.1.14 | Counter | read-only | Port counter of collision flags. |
| CTR ePortStatDataRateMismatch | 1.3.6.1.4.1.298.1.3.3.1.4.1.12 | Counter | read-only | Port counter of errors where incoming data rate is not with in the tolerance level of 10 MHZ + or - 0.01%. |
| INT ePortStateAdminState | 1.3.6.1.4.1.298.1.3.4.1.1.1.9 | INTEGER | read-write | Set will manually enable or disable any port. Get will say if port has been enabled (2) or disabled (3). |
| INT ePortStateAutoPartStatus | 1.3.6.1.4.1.298.1.3.4.1.1.1.6 | INTEGER | read-only | Whether port has been autopartitioned (2) or not autopartitioned (3). |
| ePortStateCtrlEntry | 1.3.6.1.4.1.298.1.3.4.1.1.1 | not-accessible | Individual entry of port control in table. | |
| ePortStateCtrlTable | 1.3.6.1.4.1.298.1.3.4.1.1 | not-accessible | Table for port control parameters. | |
| INT ePortStateGrpIndex | 1.3.6.1.4.1.298.1.3.4.1.1.1.1 | INTEGER | read-only | The value of this object identifies the group for which this entry contains port control information. |
| INT ePortStateJabberState | 1.3.6.1.4.1.298.1.3.4.1.1.1.8 | INTEGER | read-write | Set can enable or disable jabber detection test. Get will say if jabber detection test is enabled (2) or disabled (3). |
| INT ePortStateJabberStatus | 1.3.6.1.4.1.298.1.3.4.1.1.1.7 | INTEGER | read-only | Jabber detection for port. If On(2), then jabber occurred on this port. Off(3), then no jabber occurred or jabber detection has been manually disabled. |
| INT ePortStateLinkIntegTest | 1.3.6.1.4.1.298.1.3.4.1.1.1.5 | INTEGER | read-write | Set can enable or disabled link integrity test. Get will say if link integrity test is enabled (2) or disabled (3). |
| INT ePortStateLinkStatus | 1.3.6.1.4.1.298.1.3.4.1.1.1.4 | INTEGER | read-only | Link status for particular port. On=physical link if link test enabled. Off=no physical link exists or link test is disabled. |
| INT ePortStatePolarityState | 1.3.6.1.4.1.298.1.3.4.1.1.1.12 | INTEGER | read-write | Autopolarity correction enabled or disabled. Allows hub to make electrical corrections automatically if cable does not reverse polarity within wire pairs. If do not want this correction to take place, autocorrection can be disabled. |
| INT ePortStatePolarityStatus | 1.3.6.1.4.1.298.1.3.4.1.1.1.11 | INTEGER | read-only | Polarity is correct (2) or not for this port. |
| INT ePortStatePortIndex | 1.3.6.1.4.1.298.1.3.4.1.1.1.2 | INTEGER | read-only | This value identifies the port for which this entry contains port control information. |
| INT ePortStateRDTState | 1.3.6.1.4.1.298.1.3.4.1.1.1.10 | INTEGER | read-write | Whether RecvThreshold has been enabled or disabled. Can use this to lower noise threshold (tolerance) so that longer twisted pair links can be used. |
| INT ePortStateType | 1.3.6.1.4.1.298.1.3.4.1.1.1.3 | INTEGER | read-only | Type of cabling physically connected to port. |
| CTR ePortStatFCSErrors | 1.3.6.1.4.1.298.1.3.3.1.4.1.10 | Counter | read-only | Port counter of frames that failed Cyclic Redundancy Check (CRC). |
| CTR ePortStatFragmentErrors | 1.3.6.1.4.1.298.1.3.3.1.4.1.9 | Counter | read-only | Port counter of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error). |
| CTR ePortStatFrameTooLongs | 1.3.6.1.4.1.298.1.3.3.1.4.1.6 | Counter | read-only | Port counter for data frames longer than 1518 bytes, with a SFD and good FCS. |
| CTR ePortStatIFGErrors | 1.3.6.1.4.1.298.1.3.3.1.4.1.11 | Counter | read-only | Port counter of Interframe Gap Errors where time period between data frames is less than 5.5 micro seconds. |
| ePortStatisticsEntry | 1.3.6.1.4.1.298.1.3.3.1.4.1 | not-accessible | Entry for individual port in table. | |
| ePortStatisticsTable | 1.3.6.1.4.1.298.1.3.3.1.4 | not-accessible | Table for port specific network statistics. | |
| CTR ePortStatLateCollisions | 1.3.6.1.4.1.298.1.3.3.1.4.1.15 | Counter | read-only | Port counter of collisions occurring after the 64 byte collision window. |
| CTR ePortStatMcastFrames | 1.3.6.1.4.1.298.1.3.3.1.4.1.4 | Counter | read-only | Port counter of number of muliticast frames. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included. |
| CTR ePortStatMJLPs | 1.3.6.1.4.1.298.1.3.3.1.4.1.16 | Counter | read-only | Port counter of MAU jabber lockup protection where hub repeater chip goes into lockup state. |
| CTR ePortStatReadableFrames | 1.3.6.1.4.1.298.1.3.3.1.4.1.3 | Counter | read-only | Port counter of good or readable frames. Frame is between 64 and 1518 bytes in length and has SFD and good FCS. |
| CTR ePortStatRunts | 1.3.6.1.4.1.298.1.3.3.1.4.1.7 | Counter | read-only | Port counter for data frames with size less than 64 bytes, with no CRC or alignment errors. |
| CTR ePortStatSFDMissing | 1.3.6.1.4.1.298.1.3.3.1.4.1.18 | Counter | read-only | Port counter of a burst of data greater than or equal to 10 bytes in length with no SFD. |
| CTR ePortStatShortEvents | 1.3.6.1.4.1.298.1.3.3.1.4.1.13 | Counter | read-only | Port counter of data burst where data is less than 10 bytes in length, with no SFD. |
| INT eSmartHub3in1LnConStatus | 1.3.6.1.4.1.298.1.3.2.1.7 | INTEGER | read-only | Status of 3In1 Uplink which is located on rear panel of hub. Describes the physical link type or types currently connected. |
| INT eSmartHub3in1StateCtrl | 1.3.6.1.4.1.298.1.3.2.1.8 | INTEGER | read-write | Whether using Auto-sense or manually selected a particular media type for the uplink connection. If using Auto-sense it first tries AUI. If AUI is not present then 10T. If neither AUI nor 10T is present, then it defaults to BNC. |
| INT eSmartHubAssignedId | 1.3.6.1.4.1.298.1.3.2.1.2 | INTEGER | read-only | Assigned hub ID for Out-of-Band. |
| eSmartHubConfig | 1.3.6.1.4.1.298.1.3.2.1 | |||
| OCT eSmartHubHwLoadPatCapacity | 1.3.6.1.4.1.298.1.3.2.1.5 | OCTET STRING | read-only | What kind of function the PLD can perform. |
| INT eSmartHubHwLoadPatStatus | 1.3.6.1.4.1.298.1.3.2.1.4 | INTEGER | read-write | Which logic configuration pattern is loaded into the Programmable Logic Device PLD. |
| PHY eSmartHubId | 1.3.6.1.4.1.298.1.3.2.1.1 | PhysAddress | read-only | Hub MAC address (octet string) found from prom chip in hub. |
| INT eSmartHubNodeAgeTimer | 1.3.6.1.4.1.298.1.3.2.1.6 | INTEGER | read-write | How long to keep node entry in node summary table, measured in sec. The maximum is 11 hours. |
| eSmartHubSpec | 1.3.6.1.4.1.298.1.3.3.1.6.1 | |||
| INT eSmartHubTerSwitch | 1.3.6.1.4.1.298.1.3.2.1.3 | INTEGER | read-only | Status of position of PC/terminal switch located on rear panel of hub. Switches between serial and parallel communications for modem/PC or terminal connection to RS-232 Port. Up (off) for PC, down (on) for terminal. If position of switch is changed, there will be no change in this status until hub is reset. |
| eSpecific | 1.3.6.1.4.1.298.1.3.3.1.6 | |||
| eStateCtrl | 1.3.6.1.4.1.298.1.3.4.1 | |||
| eStatistics | 1.3.6.1.4.1.298.1.3.3.1 | |||
| eTrafficMatrixEntry | 1.3.6.1.4.1.298.1.3.3.1.5.1 | not-accessible | Individual entry in matrix of packet lengths table. | |
| CTR eTrafficMatrixFramesCount | 1.3.6.1.4.1.298.1.3.3.1.5.1.3 | Counter | read-only | Counter for number of frames received for particular range specified by the MatrixRange. |
| INT eTrafficMatrixLength | 1.3.6.1.4.1.298.1.3.3.1.5.1.1 | INTEGER | read-only | Starting length for each range in table. |
| INT eTrafficMatrixRange | 1.3.6.1.4.1.298.1.3.3.1.5.1.2 | INTEGER | read-only | Range of packet sizes to be scanned for in network traffic. |
| eTrafficMatrixTable | 1.3.6.1.4.1.298.1.3.3.1.5 | not-accessible | Table to analyze the number of packets received through network traffic by the size of each packet. | |
| INT eUtilGraphBar | 1.3.6.1.4.1.298.1.3.3.1.6.1.2 | INTEGER | read-only | Information on hardware LED for utilization graph bar. |
| hub1012 | 1.3.6.1.4.1.298.2.2.1 | |||
| IP ipagentBootServerAddr | 1.3.6.1.4.1.298.1.1.5.1.4 | IpAddress | read-write | The IP address of the boot server that was used for booting this ipagent. This parameter will always be updated in the EEPROM. |
| IP ipagentDefaultGateway | 1.3.6.1.4.1.298.1.1.5.1.3 | IpAddress | read-write | The ipagent's administrative default gateway IP address. The current operational IP default gateway IP address can be obtained from the ipRouteDest in the ipRouteTable. This parameter will take effect only after reset hub. This parameter will always be updated in the EEPROM. |
| IP ipagentIpAddr | 1.3.6.1.4.1.298.1.1.5.1.1 | IpAddress | read-write | The ipagent's administrative IP address. The current operational IP address can be obtained from the ipAdEntAddr in the ipAddrTable. This parameter will take effect only after reset hub. This parameter will always be updated in the EEPROM. |
| IP ipagentIpNetMask | 1.3.6.1.4.1.298.1.1.5.1.2 | IpAddress | read-write | The ipagent's administrative IP subnet mask. The current operational IP subnet mask can be obtained from the ipAdEntMask in the ipAddrTable. This parameter will take effect only after reset hub. This parameter will always be updated in the EEPROM. |
| ipagentProtocol | 1.3.6.1.4.1.298.1.1.5.1 | |||
| OCT ipagentTrapRcvrComm | 1.3.6.1.4.1.298.1.1.5.2.1.3 | OCTET STRING | read-write | Community string for traps sent to this trap receiver. |
| ipagentTrapRcvrEntry | 1.3.6.1.4.1.298.1.1.5.2.1 | not-accessible | Destination IP address and community string for a particular trap server. | |
| IP ipagentTrapRcvrIpAddr | 1.3.6.1.4.1.298.1.1.5.2.1.1 | IpAddress | read-only | IP address for trap server receiving trap. |
| INT ipagentTrapRcvrStatus | 1.3.6.1.4.1.298.1.1.5.2.1.2 | INTEGER | read-write | Validation of individual trap receiver. If value of this object is set to invalid(3), then that particular entry is deemed invalid, meaning that the address for that entry is no longer valid because the entry has been removed from the table. |
| ipagentTrapRcvrTable | 1.3.6.1.4.1.298.1.1.5.2 | not-accessible | Table consisting of the list of Network Management Stations that are to receive traps generated by this agent. | |
| OCT ipagentUnAuthComm | 1.3.6.1.4.1.298.1.1.5.1.6 | OCTET STRING | read-only | The community string of the last station that tried to access this ipagent with an invalid community string. |
| IP ipagentUnAuthIP | 1.3.6.1.4.1.298.1.1.5.1.5 | IpAddress | read-only | The IP address of the last station that tried to access this ipagent with an invalid community string. |
| INT nodeSecuLev1Action | 1.3.6.1.4.1.298.1.3.5.2.1.1.5 | INTEGER | read-write | Set action for node intrusion violation. |
| PHY nodeSecuLev1AllowedAddr | 1.3.6.1.4.1.298.1.3.5.2.1.1.4 | PhysAddress | read-write | MAC address of nodes allowed for particular port. |
| nodeSecuLev1Entry | 1.3.6.1.4.1.298.1.3.5.2.1.1 | not-accessible | Individual entry for node security table. | |
| INT nodeSecuLev1GrpIndex | 1.3.6.1.4.1.298.1.3.5.2.1.1.1 | INTEGER | read-only | Group ID for port which verifying node access. |
| INT nodeSecuLev1PortIndex | 1.3.6.1.4.1.298.1.3.5.2.1.1.2 | INTEGER | read-only | Specific port for which verifying node access. |
| INT nodeSecuLev1Status | 1.3.6.1.4.1.298.1.3.5.2.1.1.3 | INTEGER | read-write | Address is valid or invalid. |
| nodeSecuLev1Table | 1.3.6.1.4.1.298.1.3.5.2.1 | not-accessible | Table of nodes which have access to particular ports. Nodes are identified by MAC address. | |
| NTF nodeSecuLevel1 | 1.3.6.1.4.1.298.0.2 | The SNMP trap that is generated when the MAC layer address of the incoming frame from a particular port does not match the pre-assigned address with that port, and generates an event that is configured for sending SNMP traps. | ||
| nodeSecurity | 1.3.6.1.4.1.298.1.3.5.2 | |||
| PHY nodeSummaryDestMacAddr | 1.3.6.1.4.1.298.1.3.5.1.1.4 | PhysAddress | read-only | The destination MAC address of the node to which frames are being received by this port. |
| nodeSummaryEntry | 1.3.6.1.4.1.298.1.3.5.1.1 | not-accessible | Individual entry in node summary table. | |
| INT nodeSummaryEtherType | 1.3.6.1.4.1.298.1.3.5.1.1.5 | INTEGER | read-only | The 2 bytes after the source (src) address in packet. |
| INT nodeSummaryGrpIndex | 1.3.6.1.4.1.298.1.3.5.1.1.1 | INTEGER | read-only | Group Id for identifying the group where node activity is detected. |
| OCT nodeSummaryIpAddrPair | 1.3.6.1.4.1.298.1.3.5.1.1.6 | OCTET STRING | read-only | Destination and source IP address if packet is an Ethernet IP packet. It the packet is not an Ethernet IP packet, then the information may not be accurate. |
| INT nodeSummaryPortIndex | 1.3.6.1.4.1.298.1.3.5.1.1.2 | INTEGER | read-only | Port Id for identifying the port where node activity is detected. |
| PHY nodeSummarySrcMacAddr | 1.3.6.1.4.1.298.1.3.5.1.1.3 | PhysAddress | read-only | The source MAC address of the node that is transmitting frames received by this port. |
| nodeSummaryTable | 1.3.6.1.4.1.298.1.3.5.1 | not-accessible | Node summary of all traffic through hub. | |
| productId | 1.3.6.1.4.1.298.2 | |||
| products | 1.3.6.1.4.1.298.1 | |||
| snmpAgent | 1.3.6.1.4.1.298.1.1 | |||
| thresholdAlarm | 1.3.6.1.4.1.298.1.3.6.1 | |||
| NTF thresholdLev1 | 1.3.6.1.4.1.298.0.1 | The SNMP trap that is generated when an alarm entry crosses its rising threshold or falling threshold, and generates an event that is configured for sending SNMP traps. | ||
| INT thresholdLev1DetectedValue | 1.3.6.1.4.1.298.1.3.6.1.1.1.10 | INTEGER | read-only | The value of the statistic for the last sampling period. |
| thresholdLev1Entry | 1.3.6.1.4.1.298.1.3.6.1.1.1 | not-accessible | Individual entry in threshold trap table. | |
| INT thresholdLev1FallingEvent | 1.3.6.1.4.1.298.1.3.6.1.1.1.12 | INTEGER | read-write | How to respond to a triggered event for a falling event. |
| INT thresholdLev1GroupIndex | 1.3.6.1.4.1.298.1.3.6.1.1.1.4 | INTEGER | read-write | Group ID for trap set. One note--if the target is selected as hub, the group index will be ignored. |
| INT thresholdLev1Index | 1.3.6.1.4.1.298.1.3.6.1.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the alarm table. |
| INT thresholdLev1Interval | 1.3.6.1.4.1.298.1.3.6.1.1.1.13 | INTEGER | read-write | The interval in seconds over which the data is sampled. |
| OCT thresholdLev1OwnerString | 1.3.6.1.4.1.298.1.3.6.1.1.1.14 | OCTET STRING | read-write | 8-byte octet reserved for the owner who defined this entry. |
| INT thresholdLev1PortIndex | 1.3.6.1.4.1.298.1.3.6.1.1.1.5 | INTEGER | read-write | Port number for trap set. One note--if the target is selected as hub, the port index will be ignored. |
| INT thresholdLev1RisingEvent | 1.3.6.1.4.1.298.1.3.6.1.1.1.11 | INTEGER | read-write | How to respond to a triggered event for a rising event. |
| INT thresholdLev1SampleType | 1.3.6.1.4.1.298.1.3.6.1.1.1.7 | INTEGER | read-write | The method of sampling the selected variable and calculating the value to be compared against the threshold. |
| INT thresholdLev1StartupAlarm | 1.3.6.1.4.1.298.1.3.6.1.1.1.8 | INTEGER | read-write | When the trap is triggered in relation to value set. When goes above (2), below (3), or changes at all from (4). |
| INT thresholdLev1Status | 1.3.6.1.4.1.298.1.3.6.1.1.1.2 | INTEGER | read-write | Status of entry in threshold/trap table. |
| INT thresholdLev1Subject | 1.3.6.1.4.1.298.1.3.6.1.1.1.6 | INTEGER | read-write | Variable checking for in trap. These are the type of frames that a trap will be verified against. |
| thresholdLev1Table | 1.3.6.1.4.1.298.1.3.6.1.1 | not-accessible | Threshold/trap table. | |
| INT thresholdLev1Target | 1.3.6.1.4.1.298.1.3.6.1.1.1.3 | INTEGER | read-write | Set target for threshold definition. Either whole hub(2) or particular port (3). |
| INT thresholdLev1WaterMark | 1.3.6.1.4.1.298.1.3.6.1.1.1.9 | INTEGER | read-write | Counter of threshold. |
RFC description
Asante Hub 1012 Ethernet hub MIB; provides configuration and status monitoring for a legacy 12-port repeater hub.
Start monitoring Asante HUB1012 Ethernet repeater/hub (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.