ASANTE-AH1012-MIB

All MIBs › ASANTE-AH1012-MIB

Category: Network Interfaces

Description: Manages Asante AH1012 Ethernet hub port status, counters, and configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ASANTE-AH1012-MIB?

The ASANTE-AH1012-MIB is a vendor-specific SNMP module for Asante's AH1012 series Ethernet hub, an entry-level networking device from the era of shared-media Ethernet hubs. It exposes agent-level data such as firmware/image version information, hardware revision, boot/reset control, remote-boot configuration (protocol, file, dial string, baud rate), and general product identification. Administrators use it primarily to confirm hardware and firmware health of the hub agent itself, checking the running image's major/minor version, hardware revision, and whether the device needs a reset or remote reload, rather than monitoring rich traffic statistics. It does not appear to layer on other standard MIBs beyond basic SNMPv2-SMI conventions. It would typically be deployed in small legacy Ethernet networks where an Asante hub still provides basic connectivity and needs periodic firmware/config verification. Engineers can download the ASANTE-AH1012-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ASANTE-AH1012-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Asante AH1012 Ethernet hub

Monitoring Examples

An administrator polling agentRunTimeImageMajorVer and agentRunTimeImageMinorVer can confirm which firmware build is active on the hub agent and detect a failed or partial upgrade. agentHwVer and agentHwReVer reveal the underlying hardware revision, useful when auditing a fleet of AH1012 hubs for compatibility with a firmware update. The agentReset object lets an operator trigger a remote reboot, while agentRemoteBootInfo/agentRemoteBootProtocol/agentRemoteBootFile describe how the unit fetches its image over the network, letting staff verify a remote-boot server is correctly configured.

What Can Be Monitored

firmware image version
hardware revision
remote boot protocol and file
boot mode configuration
agent reset status
product/model identification

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
NetworkAddress
TimeTicks
private

From SNMPv2-SMI

enterprises

OIDs

OID symbolic	OID numeric	Type	Access	Description
adaptCard	1.3.6.1.4.1.298.1.2
adapterProductId	1.3.6.1.4.1.298.2.1
agentFw	1.3.6.1.4.1.298.1.1.2
INT agentFwMajorVer	1.3.6.1.4.1.298.1.1.2.1	INTEGER	read-only	The major firmware version number of the agent prom code.
INT agentFwMinorVer	1.3.6.1.4.1.298.1.1.2.2	INTEGER	read-only	The minor firmware version number of the agent prom code.
agentHw	1.3.6.1.4.1.298.1.1.3
INT agentHwReVer	1.3.6.1.4.1.298.1.1.3.1	INTEGER	read-only	The hardware reversion number of the network management module.
INT agentHwVer	1.3.6.1.4.1.298.1.1.3.2	INTEGER	read-only	The hardware model number of the network management module
INT agentImageLoadMode	1.3.6.1.4.1.298.1.1.1.3	INTEGER	read-write	Tells hub whether the software image is to be loaded from the FLASH EPROM or from over the network.
agentNetProtocol	1.3.6.1.4.1.298.1.1.5
OCT agentNetProtoStkCapMap	1.3.6.1.4.1.298.1.1.4	OCTET STRING	read-only	This octet string represents the current protocol stack configuration supported by the agent, encoded as a bit string. Each protocol stack is represented by a single bit. When the value of a bit = 1, it indicates that the protocol stack on the agent represented by that bit is supported; when zero, the protocol stack is not supported. The number of octets in the string is always integer multiple of the octet. The first protocol stack will encode in the least significant bit of the first octet. Current, only IP Stack(bit 0) and IPX Stack(bit 1) were defined, all other bits should be zero.
INT agentOutBandBaudRate	1.3.6.1.4.1.298.1.1.1.8	INTEGER	read-write	The baud rate setting for the out-of-band port.
OCT agentOutBandDialString	1.3.6.1.4.1.298.1.1.1.7	OCTET STRING	read-write	This is the initialization string used by the Network Management station to establish the out-of-band connection for modem only.
OCT agentRemoteBootFile	1.3.6.1.4.1.298.1.1.1.6	OCTET STRING	read-write	The boot file name that is sent to the boot file server by agent boot code during boot time.
INT agentRemoteBootInfo	1.3.6.1.4.1.298.1.1.1.4	INTEGER	read-only	The method for getting boot parameter information.
INT agentRemoteBootProtocol	1.3.6.1.4.1.298.1.1.1.5	INTEGER	read-write	The netboot protocol that used to load the agent software.
INT agentReset	1.3.6.1.4.1.298.1.1.1.9	INTEGER	read-write	The object to allow software to perform 'push_button' system reset.
INT agentRunTimeImageMajorVer	1.3.6.1.4.1.298.1.1.1.1	INTEGER	read-only	The major software version number of the agent run time image.
INT agentRunTimeImageMinorVer	1.3.6.1.4.1.298.1.1.1.2	INTEGER	read-only	The minor software version number of the agent run time image.
agentSw	1.3.6.1.4.1.298.1.1.1
asante	1.3.6.1.4.1.298
concAlarmMgt	1.3.6.1.4.1.298.1.3.6
concBasicGrp	1.3.6.1.4.1.298.1.3.1.1
concChassis	1.3.6.1.4.1.298.1.3.1
INT concChassisBkplRev	1.3.6.1.4.1.298.1.3.1.1.3	INTEGER	read-only	The concentrator's chassis backplane revision number.
INT concChassisBkplType	1.3.6.1.4.1.298.1.3.1.1.2	INTEGER	read-only	The concentrator's chassis backplane type.
INT concChassisFanStatus	1.3.6.1.4.1.298.1.3.1.1.5	INTEGER	read-only	The value of this object identifies the fan status.
INT concChassisGroupCapacity	1.3.6.1.4.1.298.1.3.1.1.6	INTEGER	read-only	The number of groups that can be contained within the concentrator.
OCT concChassisGroupMap	1.3.6.1.4.1.298.1.3.1.1.7	OCTET STRING	read-only	This octet string represents the current configuration of groups, encoded as a bit string, each group is represented by a single bit.
STR concChassisGrpDescr	1.3.6.1.4.1.298.1.3.1.1.8.1.4	DisplayString	read-only	A description of this group device.
concChassisGrpEntry	1.3.6.1.4.1.298.1.3.1.1.8.1		not-accessible	A list of information for each slot in this chassis.
INT concChassisGrpHwRev	1.3.6.1.4.1.298.1.3.1.1.8.1.5	INTEGER	read-only	The hardware revision number of this particular group.
INT concChassisGrpIndex	1.3.6.1.4.1.298.1.3.1.1.8.1.1	INTEGER	read-only	The value of this object identifies the chassis group table for which this entry contains group related information.
INT concChassisGrpNumberPort	1.3.6.1.4.1.298.1.3.1.1.8.1.2	INTEGER	read-only	The number of port is available for up/down link within this group.
concChassisGrpTable	1.3.6.1.4.1.298.1.3.1.1.8		not-accessible	A table that contains information about the group/slot in this chassis.
INT concChassisGrpType	1.3.6.1.4.1.298.1.3.1.1.8.1.3	INTEGER	read-only	The value represents the function of this group.
concChassisPsEntry	1.3.6.1.4.1.298.1.3.1.1.4.1		not-accessible	The entry in the table containing the information about a single power supply.
INT concChassisPsIndex	1.3.6.1.4.1.298.1.3.1.1.4.1.1	INTEGER	read-only	The value of this object identifies the power supply table for which this entry contains power supply type and status.
INT concChassisPsModuleType	1.3.6.1.4.1.298.1.3.1.1.4.1.2	INTEGER	read-only	The value of this object identifies the power supply module type.
INT concChassisPsStatus	1.3.6.1.4.1.298.1.3.1.1.4.1.3	INTEGER	read-only	The value of this object identifies the power supply module status.
concChassisPsTable	1.3.6.1.4.1.298.1.3.1.1.4		not-accessible	This table contains concentrator's power supply information.
INT concChassisType	1.3.6.1.4.1.298.1.3.1.1.1	INTEGER	read-only	The concentrator's chassis type.
concConfiguration	1.3.6.1.4.1.298.1.3.2
concentrator	1.3.6.1.4.1.298.1.3
concNodeMgt	1.3.6.1.4.1.298.1.3.5
concProductId	1.3.6.1.4.1.298.2.2
concStateCtrl	1.3.6.1.4.1.298.1.3.4
concStatistics	1.3.6.1.4.1.298.1.3.3
INT eColGraphBar	1.3.6.1.4.1.298.1.3.3.1.6.1.1	INTEGER	read-only	Information on hardware LED collision graph bar.
CTR eGlobalHubAlignmentErrors	1.3.6.1.4.1.298.1.3.3.1.1.6	Counter	read-only	Global counter, for this hub, of frames which are not integer multiples of 1 byte.
CTR eGlobalHubAutoPartitions	1.3.6.1.4.1.298.1.3.3.1.1.15	Counter	read-only	Global counter, for this hub, of all ports including 3in1 port being partitioned from network in response to 31 or more continuous collisions.
CTR eGlobalHubBadFrames	1.3.6.1.4.1.298.1.3.3.1.1.17	Counter	read-only	Global counter, for this hub, of total errored frame including toolong, runts, misaligned, or bad FCS.
CTR eGlobalHubBcastFrames	1.3.6.1.4.1.298.1.3.3.1.1.3	Counter	read-only	Global counter of number of broadcast frames for his hub. All 1s in network destination address. Multicast packets are not included.
CTR eGlobalHubCollisions	1.3.6.1.4.1.298.1.3.3.1.1.12	Counter	read-only	Global counter of collision flags, for this hub.
CTR eGlobalHubDataRateMismatchs	1.3.6.1.4.1.298.1.3.3.1.1.10	Counter	read-only	Global counter, for this hub, of errors where incoming data rate is not with in the tolerance level of 10MHZ + or - 0.01%.
CTR eGlobalHubFCSErrors	1.3.6.1.4.1.298.1.3.3.1.1.8	Counter	read-only	Global counter, for this hub, of frames that failed Cyclic Redundancy Check (CRC).
CTR eGlobalHubFragmentErrors	1.3.6.1.4.1.298.1.3.3.1.1.7	Counter	read-only	Global counter, for this hub, of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error).
CTR eGlobalHubFrameTooLongs	1.3.6.1.4.1.298.1.3.3.1.1.4	Counter	read-only	Global counter, for this hub, of data frames longer than 1518 bytes, with a SFD and good FCS.
CTR eGlobalHubIFGErrors	1.3.6.1.4.1.298.1.3.3.1.1.9	Counter	read-only	Global counter, for this hub, of occurrences of Interframe Gap Errors where time period between data frames is less than 5.5 micro seconds.
CTR eGlobalHubLateCollisions	1.3.6.1.4.1.298.1.3.3.1.1.13	Counter	read-only	Global counter, for this hub, of collisions occurring after the 64 byte collision window.
CTR eGlobalHubMcastFrames	1.3.6.1.4.1.298.1.3.3.1.1.2	Counter	read-only	Global counter of number of multicast frames for this hub. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included.
CTR eGlobalHubMJLPs	1.3.6.1.4.1.298.1.3.3.1.1.14	Counter	read-only	Global counter of MAU jabber lockup protection where hub repeater chip goes into lockup state.
CTR eGlobalHubReadableFrames	1.3.6.1.4.1.298.1.3.3.1.1.1	Counter	read-only	Global counter of good or readable frames for this hub. Frame is between 64 and 1518 bytes in length and has SFD and good FCS.
CTR eGlobalHubRunts	1.3.6.1.4.1.298.1.3.3.1.1.5	Counter	read-only	Global counter, for this hub, of data frames with size less than 64 bytes, with no CRC or alignment errors.
CTR eGlobalHubSFDMissings	1.3.6.1.4.1.298.1.3.3.1.1.16	Counter	read-only	Global counter, for this hub, of a burst of data greater than or equal to 10 bytes in length with no SFD.
CTR eGlobalHubShortEvents	1.3.6.1.4.1.298.1.3.3.1.1.11	Counter	read-only	Global counter, for this hub, of data burst where data is less than 10 bytes in length, with no SFD.
eGlobalStatistics	1.3.6.1.4.1.298.1.3.3.1.1
CTR eGrpStatAlignmentErrors	1.3.6.1.4.1.298.1.3.3.1.3.1.7	Counter	read-only	Group counter of frames which are not integer multiples of 1 byte .
CTR eGrpStatAutoPartitions	1.3.6.1.4.1.298.1.3.3.1.3.1.16	Counter	read-only	Group counter of ports in group autopartitioned in response to 31 or more continuous collisions.
CTR eGrpStatBadFrames	1.3.6.1.4.1.298.1.3.3.1.3.1.18	Counter	read-only	Group counter of total errored frames including toolong, runts, misaligned, or bad FCS.
CTR eGrpStatBcastFrames	1.3.6.1.4.1.298.1.3.3.1.3.1.4	Counter	read-only	Group counter of number of broadcast frames. All 1s in network destination address. Multicast packets are not included.
CTR eGrpStatCollisions	1.3.6.1.4.1.298.1.3.3.1.3.1.13	Counter	read-only	Group counter of collision flags.
CTR eGrpStatDataRateMismatchs	1.3.6.1.4.1.298.1.3.3.1.3.1.11	Counter	read-only	Group counter of errors where incoming data rate is not with in the tolerance level of 10 MHZ + or - 0.01%.
CTR eGrpStatFCSErrors	1.3.6.1.4.1.298.1.3.3.1.3.1.9	Counter	read-only	Group counter frames that failed Cyclic Redundancy Check (CRC).
CTR eGrpStatFragmentErrors	1.3.6.1.4.1.298.1.3.3.1.3.1.8	Counter	read-only	Group counter of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error).
CTR eGrpStatFrameTooLongs	1.3.6.1.4.1.298.1.3.3.1.3.1.5	Counter	read-only	Group counter for data frames longer than 1518 bytes, with a SFD and good FCS.
CTR eGrpStatIFGErrors	1.3.6.1.4.1.298.1.3.3.1.3.1.10	Counter	read-only	Group counter of Interframe Gap Errors where time period between data frames is less than 5.5 micro seconds.
INT eGrpStatIndex	1.3.6.1.4.1.298.1.3.3.1.3.1.1	INTEGER	read-only	The value of this object identifies the group for which this entry contains group statistical information.
eGrpStatisticsEntry	1.3.6.1.4.1.298.1.3.3.1.3.1		not-accessible	Entry for individual group in table.
eGrpStatisticsTable	1.3.6.1.4.1.298.1.3.3.1.3		not-accessible	Table of statistical information for each group.
CTR eGrpStatLateCollisions	1.3.6.1.4.1.298.1.3.3.1.3.1.14	Counter	read-only	Group counter of collisions occurring after the 64 byte collision window.
CTR eGrpStatMcastFrames	1.3.6.1.4.1.298.1.3.3.1.3.1.3	Counter	read-only	Group counter of number of muliticast frames. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included.
CTR eGrpStatMJLPs	1.3.6.1.4.1.298.1.3.3.1.3.1.15	Counter	read-only	Group counter of MAU jabber lockup protection where hub repeater chip goes into lockup state.
CTR eGrpStatReadableFrames	1.3.6.1.4.1.298.1.3.3.1.3.1.2	Counter	read-only	Group counter of 'good' or readable frames. Frame is between 64 and 1518 bytes in length and has SFD and good FCS.
CTR eGrpStatRunts	1.3.6.1.4.1.298.1.3.3.1.3.1.6	Counter	read-only	Group counter for data frames with size less than 64 bytes, with no CRC or alignment errors.
CTR eGrpStatSFDMissings	1.3.6.1.4.1.298.1.3.3.1.3.1.17	Counter	read-only	Group counter of a burst of data greater than or equal to 10 bytes in length with no SFD.
CTR eGrpStatShortEvents	1.3.6.1.4.1.298.1.3.3.1.3.1.12	Counter	read-only	Group counter of data burst where data is less than 10 bytes in length, with no SFD.
INT ePortGrpIndex	1.3.6.1.4.1.298.1.3.3.1.4.1.1	INTEGER	read-only	The value of this object identifies the group for which this entry contains port statistical information.
INT ePortIndex	1.3.6.1.4.1.298.1.3.3.1.4.1.2	INTEGER	read-only	The value of this object identifies the port for which this entry contains port statistical information.
INT ePortRateAlignmentErrors	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.8	INTEGER	read-only	Rate of occurrence of frames which are not integer multiples of 1 byte.
INT ePortRateAutoPartitions	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.17	INTEGER	read-only	Rate of occurrence of times port was autopartitioned in response to 31 or more continuous collisions.
INT ePortRateBadFrames	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.19	INTEGER	read-only	Rate of occurrence of total errored frames including toolong, runts, misaligned, or bad FCS.
INT ePortRateBcastFrames	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.5	INTEGER	read-only	Rate of occurrence of number of broadcast frames. All 1s in network destination address. Multicast packets are not included.
INT ePortRateCollisions	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.14	INTEGER	read-only	Rate of occurrence of collision flags.
INT ePortRateDataRateMismatch	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.12	INTEGER	read-only	Rate of occurrence of errors where incoming data rate is not with in the tolerance level of 10 MHz + or - 0.01%.
ePortRateEntry	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1		not-accessible	Individual entry in port rate table.
INT ePortRateFCSErrors	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.10	INTEGER	read-only	Rate of occurrence of frames that failed Cyclic Redundancy Check (CRC).
INT ePortRateFragmentErrors	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.9	INTEGER	read-only	Rate of occurrence of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error).
INT ePortRateFrameTooLongs	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.6	INTEGER	read-only	Rate of occurrence of data frames longer than 1518 bytes, with a SFD and good FCS.
INT ePortRateGrpIndex	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.1	INTEGER	read-only	The value of this object identifies the group for which this entry contains port statistical information.
INT ePortRateIFGErrors	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.11	INTEGER	read-only	Rate of occurrence of interframe Gap Errors where time period between data frames is less than 5.5 micro seconds.
INT ePortRateLateCollisions	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.15	INTEGER	read-only	Rate of occurrence of collisions occurring after the 64 byte collision window.
INT ePortRateMcastFrames	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.4	INTEGER	read-only	Rate of occurrence of number of muliticast frames. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included.
INT ePortRateMJLPs	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.16	INTEGER	read-only	Rate of occurrence of MAU jabber lockup protection where hub repeater chip goes into lockup state.
INT ePortRatePortIndex	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.2	INTEGER	read-only	This value identifies the port for which this entry contains port statistical information.
INT ePortRateReadableFrames	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.3	INTEGER	read-only	Rate of occurrence of good or readable frames.
INT ePortRateRunts	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.7	INTEGER	read-only	Rate of occurrence of data frames with size less than 64 bytes, with no CRC or alignment errors.
INT ePortRateSFDMissings	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.18	INTEGER	read-only	Rate of occurrence of a burst of data greater than or equal to 10 bytes in length with no SFD.
INT ePortRateShortEvents	1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.13	INTEGER	read-only	Rate of occurrence of data burst where data is less than 10 bytes in length, with no SFD.
ePortRateTable	1.3.6.1.4.1.298.1.3.3.1.6.1.6		not-accessible	Network statistics for individual ports measured in Rate/Second.
CTR ePortStatAlignmentErrors	1.3.6.1.4.1.298.1.3.3.1.4.1.8	Counter	read-only	Port counter of frames which are not integer multiples of 1 byte.
CTR ePortStatAutoPartitions	1.3.6.1.4.1.298.1.3.3.1.4.1.17	Counter	read-only	Port counter of number of times port was autopartitioned in response to 31 or more continuous collisions.
CTR ePortStatBadFrames	1.3.6.1.4.1.298.1.3.3.1.4.1.19	Counter	read-only	Port counter of total errored frames including toolong, runts, misaligned, or bad FCS.
CTR ePortStatBcastFrames	1.3.6.1.4.1.298.1.3.3.1.4.1.5	Counter	read-only	Port counter of number of broadcast frames. All 1s in network destination address. Multicast packets are not included.
CTR ePortStatCollisions	1.3.6.1.4.1.298.1.3.3.1.4.1.14	Counter	read-only	Port counter of collision flags.
CTR ePortStatDataRateMismatchs	1.3.6.1.4.1.298.1.3.3.1.4.1.12	Counter	read-only	Port counter of errors where incoming data rate is not with in the tolerance level of 10 MHZ + or - 0.01%.
INT ePortStateAdminState	1.3.6.1.4.1.298.1.3.4.1.1.1.9	INTEGER	read-write	Set will manually enable or disable any port. Get will say if port has been enabled (2) or disabled (3).
INT ePortStateAutoPartStatus	1.3.6.1.4.1.298.1.3.4.1.1.1.6	INTEGER	read-only	Whether port has been autopartitioned (2) or not autopartitioned (3).
ePortStateCtrlEntry	1.3.6.1.4.1.298.1.3.4.1.1.1		not-accessible	Individual entry of port control in table.
ePortStateCtrlTable	1.3.6.1.4.1.298.1.3.4.1.1		not-accessible	Table for port control parameters.
INT ePortStateGrpIndex	1.3.6.1.4.1.298.1.3.4.1.1.1.1	INTEGER	read-only	The value of this object identifies the group for which this entry contains port control information.
INT ePortStateJabberState	1.3.6.1.4.1.298.1.3.4.1.1.1.8	INTEGER	read-write	Set can enable or disable jabber detection test. Get will say if jabber detection test is enabled (2) or disabled (3).
INT ePortStateJabberStatus	1.3.6.1.4.1.298.1.3.4.1.1.1.7	INTEGER	read-only	Jabber detection for port. If On(2), then jabber occurred on this port. Off(3), then no jabber occurred or jabber detection has been manually disabled.
INT ePortStateLinkIntegTest	1.3.6.1.4.1.298.1.3.4.1.1.1.5	INTEGER	read-write	Set can enable or disabled link integrity test. Get will say if link integrity test is enabled (2) or disabled (3).
INT ePortStateLinkStatus	1.3.6.1.4.1.298.1.3.4.1.1.1.4	INTEGER	read-only	Link status for particular port. On=physical link if link test enabled. Off=no physical link exists or link test is disabled.
INT ePortStatePolarityState	1.3.6.1.4.1.298.1.3.4.1.1.1.12	INTEGER	read-write	Autopolarity correction enabled or disabled. Allows hub to make electrical corrections automatically if cable does not reverse polarity within wire pairs. If do not want this correction to take place, autocorrection can be disabled.
INT ePortStatePolarityStatus	1.3.6.1.4.1.298.1.3.4.1.1.1.11	INTEGER	read-only	Polarity is correct (2) or not for this port.
INT ePortStatePortIndex	1.3.6.1.4.1.298.1.3.4.1.1.1.2	INTEGER	read-only	This value identifies the port for which this entry contains port control information.
INT ePortStateRDTState	1.3.6.1.4.1.298.1.3.4.1.1.1.10	INTEGER	read-write	Whether RecvThreshold has been enabled or disabled. Can use this to lower noise threshold (tolerance) so that longer twisted pair links can be used.
INT ePortStateType	1.3.6.1.4.1.298.1.3.4.1.1.1.3	INTEGER	read-only	Type of cabling physically connected to port.
CTR ePortStatFCSErrors	1.3.6.1.4.1.298.1.3.3.1.4.1.10	Counter	read-only	Port counter of frames that failed Cyclic Redundancy Check (CRC).
CTR ePortStatFragmentErrors	1.3.6.1.4.1.298.1.3.3.1.4.1.9	Counter	read-only	Port counter of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error).
CTR ePortStatFrameTooLongs	1.3.6.1.4.1.298.1.3.3.1.4.1.6	Counter	read-only	Port counter for data frames longer than 1518 bytes, with a SFD and good FCS.
CTR ePortStatIFGErrors	1.3.6.1.4.1.298.1.3.3.1.4.1.11	Counter	read-only	Port counter of Interframe Gap Errors where time period between data frames is less than 5.5 micro seconds.
ePortStatisticsEntry	1.3.6.1.4.1.298.1.3.3.1.4.1		not-accessible	Entry for individual port in table.
ePortStatisticsTable	1.3.6.1.4.1.298.1.3.3.1.4		not-accessible	Table for port specific network statistics.
CTR ePortStatLateCollisions	1.3.6.1.4.1.298.1.3.3.1.4.1.15	Counter	read-only	Port counter of collisions occurring after the 64 byte collision window.
CTR ePortStatMcastFrames	1.3.6.1.4.1.298.1.3.3.1.4.1.4	Counter	read-only	Port counter of number of muliticast frames. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included.
CTR ePortStatMJLPs	1.3.6.1.4.1.298.1.3.3.1.4.1.16	Counter	read-only	Port counter of MAU jabber lockup protection where hub repeater chip goes into lockup state.
CTR ePortStatReadableFrames	1.3.6.1.4.1.298.1.3.3.1.4.1.3	Counter	read-only	Port counter of good or readable frames. Frame is between 64 and 1518 bytes in length and has SFD and good FCS.
CTR ePortStatRunts	1.3.6.1.4.1.298.1.3.3.1.4.1.7	Counter	read-only	Port counter for data frames with size less than 64 bytes, with no CRC or alignment errors.
CTR ePortStatSFDMissings	1.3.6.1.4.1.298.1.3.3.1.4.1.18	Counter	read-only	Port counter of a burst of data greater than or equal to 10 bytes in length with no SFD.
CTR ePortStatShortEvents	1.3.6.1.4.1.298.1.3.3.1.4.1.13	Counter	read-only	Port counter of data burst where data is less than 10 bytes in length, with no SFD.
INT eSmartHub3in1LnConStatus	1.3.6.1.4.1.298.1.3.2.1.7	INTEGER	read-only	Status of 3In1 Uplink which is located on rear panel of hub. Describes the physical link type or types currently connected.
INT eSmartHub3in1StateCtrl	1.3.6.1.4.1.298.1.3.2.1.8	INTEGER	read-write	Whether using Auto-sense or manually selected a particular media type for the uplink connection. If using Auto-sense it first tries AUI. If AUI is not present then 10T. If neither AUI nor 10T is present, then it defaults to BNC.
INT eSmartHubAssignedId	1.3.6.1.4.1.298.1.3.2.1.2	INTEGER	read-only	Assigned hub ID for Out-of-Band.
eSmartHubConfig	1.3.6.1.4.1.298.1.3.2.1
OCT eSmartHubHwLoadPatCapacity	1.3.6.1.4.1.298.1.3.2.1.5	OCTET STRING	read-only	What kind of function the PLD can perform.
INT eSmartHubHwLoadPatStatus	1.3.6.1.4.1.298.1.3.2.1.4	INTEGER	read-write	Which logic configuration pattern is loaded into the Programmable Logic Device PLD.
PHY eSmartHubId	1.3.6.1.4.1.298.1.3.2.1.1	PhysAddress	read-only	Hub MAC address (octet string) found from prom chip in hub.
INT eSmartHubNodeAgeTimer	1.3.6.1.4.1.298.1.3.2.1.6	INTEGER	read-write	How long to keep node entry in node summary table, measured in sec. The maximum is 11 hours.
eSmartHubSpec	1.3.6.1.4.1.298.1.3.3.1.6.1
INT eSmartHubTerSwitch	1.3.6.1.4.1.298.1.3.2.1.3	INTEGER	read-only	Status of position of PC/terminal switch located on rear panel of hub. Switches between serial and parallel communications for modem/PC or terminal connection to RS-232 Port. Up (off) for PC, down (on) for terminal. If position of switch is changed, there will be no change in this status until hub is reset.
eSpecific	1.3.6.1.4.1.298.1.3.3.1.6
eStateCtrl	1.3.6.1.4.1.298.1.3.4.1
eStatistics	1.3.6.1.4.1.298.1.3.3.1
eTrafficMatrixEntry	1.3.6.1.4.1.298.1.3.3.1.5.1		not-accessible	Individual entry in matrix of packet lengths table.
CTR eTrafficMatrixFramesCounts	1.3.6.1.4.1.298.1.3.3.1.5.1.3	Counter	read-only	Counter for number of frames received for particular range specified by the MatrixRange.
INT eTrafficMatrixLength	1.3.6.1.4.1.298.1.3.3.1.5.1.1	INTEGER	read-only	Starting length for each range in table.
INT eTrafficMatrixRange	1.3.6.1.4.1.298.1.3.3.1.5.1.2	INTEGER	read-only	Range of packet sizes to be scanned for in network traffic.
eTrafficMatrixTable	1.3.6.1.4.1.298.1.3.3.1.5		not-accessible	Table to analyze the number of packets received through network traffic by the size of each packet.
INT eUtilGraphBar	1.3.6.1.4.1.298.1.3.3.1.6.1.2	INTEGER	read-only	Information on hardware LED for utilization graph bar.
hub1012	1.3.6.1.4.1.298.2.2.1
hub1012_bridge	1.3.6.1.4.1.298.2.2.2
IP ipagentBootServerAddr	1.3.6.1.4.1.298.1.1.5.1.4	IpAddress	read-write	The IP address of the boot server that was used for booting this ipagent. This parameter will always be updated in the EEPROM.
IP ipagentDefaultGateway	1.3.6.1.4.1.298.1.1.5.1.3	IpAddress	read-write	The ipagent's administrative default gateway IP address. The current operational IP default gateway IP address can be obtained from the ipRouteDest in the ipRouteTable. This parameter will take effect only after reset hub. This parameter will always be updated in the EEPROM.
IP ipagentIpAddr	1.3.6.1.4.1.298.1.1.5.1.1	IpAddress	read-write	The ipagent's administrative IP address. The current operational IP address can be obtained from the ipAdEntAddr in the ipAddrTable. This parameter will take effect only after reset hub. This parameter will always be updated in the EEPROM.
IP ipagentIpNetMask	1.3.6.1.4.1.298.1.1.5.1.2	IpAddress	read-write	The ipagent's administrative IP subnet mask. The current operational IP subnet mask can be obtained from the ipAdEntMask in the ipAddrTable. This parameter will take effect only after reset hub. This parameter will always be updated in the EEPROM.
ipagentProtocol	1.3.6.1.4.1.298.1.1.5.1
OCT ipagentTrapRcvrComm	1.3.6.1.4.1.298.1.1.5.2.1.3	OCTET STRING	read-write	Community string for traps sent to this trap receiver.
ipagentTrapRcvrEntry	1.3.6.1.4.1.298.1.1.5.2.1		not-accessible	Destination IP address and community string for a particular trap server.
IP ipagentTrapRcvrIpAddr	1.3.6.1.4.1.298.1.1.5.2.1.1	IpAddress	read-only	IP address for trap server receiving trap.
INT ipagentTrapRcvrStatus	1.3.6.1.4.1.298.1.1.5.2.1.2	INTEGER	read-write	Validation of individual trap receiver. If value of this object is set to invalid(3), then that particular entry is deemed invalid, meaning that the address for that entry is no longer valid because the entry has been removed from the table.
ipagentTrapRcvrTable	1.3.6.1.4.1.298.1.1.5.2		not-accessible	Table consisting of the list of Network Management Stations that are to receive traps generated by this agent.
OCT ipagentUnAuthComm	1.3.6.1.4.1.298.1.1.5.1.6	OCTET STRING	read-only	The community string of the last station that tried to access this ipagent with an invalid community string.
IP ipagentUnAuthIP	1.3.6.1.4.1.298.1.1.5.1.5	IpAddress	read-only	The IP address of the last station that tried to access this ipagent with an invalid community string.
INT nodeSecuLev1Action	1.3.6.1.4.1.298.1.3.5.2.1.1.5	INTEGER	read-write	Set action for node intrusion violation.
PHY nodeSecuLev1AllowedAddr	1.3.6.1.4.1.298.1.3.5.2.1.1.4	PhysAddress	read-write	MAC address of nodes allowed for particular port.
nodeSecuLev1Entry	1.3.6.1.4.1.298.1.3.5.2.1.1		not-accessible	Individual entry for node security table.
INT nodeSecuLev1GrpIndex	1.3.6.1.4.1.298.1.3.5.2.1.1.1	INTEGER	read-only	Group ID for port which verifying node access.
INT nodeSecuLev1PortIndex	1.3.6.1.4.1.298.1.3.5.2.1.1.2	INTEGER	read-only	Specific port for which verifying node access.
INT nodeSecuLev1Status	1.3.6.1.4.1.298.1.3.5.2.1.1.3	INTEGER	read-write	Address is valid or invalid.
nodeSecuLev1Table	1.3.6.1.4.1.298.1.3.5.2.1		not-accessible	Table of nodes which have access to particular ports. Nodes are identified by MAC address.
NTF nodeSecuLevel1	1.3.6.1.4.1.298.2.2.1.0.2			The SNMP trap that is generated when the MAC layer address of the incoming frame from a particular port does not match the pre-assigned address with that port, and generates an event that is configured for sending SNMP traps.
nodeSecurity	1.3.6.1.4.1.298.1.3.5.2
PHY nodeSummaryDestMacAddr	1.3.6.1.4.1.298.1.3.5.1.1.4	PhysAddress	read-only	The destination MAC address of the node to which frames are being received by this port.
nodeSummaryEntry	1.3.6.1.4.1.298.1.3.5.1.1		not-accessible	Individual entry in node summary table.
INT nodeSummaryEtherType	1.3.6.1.4.1.298.1.3.5.1.1.5	INTEGER	read-only	The 2 bytes after the source (src) address in packet.
INT nodeSummaryGrpIndex	1.3.6.1.4.1.298.1.3.5.1.1.1	INTEGER	read-only	Group Id for identifying the group where node activity is detected.
OCT nodeSummaryIpAddrPair	1.3.6.1.4.1.298.1.3.5.1.1.6	OCTET STRING	read-only	Destination and source IP address if packet is an Ethernet IP packet. It the packet is not an Ethernet IP packet, then the information may not be accurate.
INT nodeSummaryPortIndex	1.3.6.1.4.1.298.1.3.5.1.1.2	INTEGER	read-only	Port Id for identifying the port where node activity is detected.
PHY nodeSummarySrcMacAddr	1.3.6.1.4.1.298.1.3.5.1.1.3	PhysAddress	read-only	The source MAC address of the node that is transmitting frames received by this port.
nodeSummaryTable	1.3.6.1.4.1.298.1.3.5.1		not-accessible	Node summary of all traffic through hub.
TIK nodeSummaryTimeStamp	1.3.6.1.4.1.298.1.3.5.1.1.7	TimeTicks	read-only	nodeSummary entry time stamp (in hundredths of a second) since the network management portion of the system was last re-initialized.
productId	1.3.6.1.4.1.298.2
products	1.3.6.1.4.1.298.1
snmpAgent	1.3.6.1.4.1.298.1.1
thresholdAlarm	1.3.6.1.4.1.298.1.3.6.1
NTF thresholdLev1	1.3.6.1.4.1.298.2.2.1.0.1			The SNMP trap that is generated when an alarm entry crosses its rising threshold or falling threshold, and generates an event that is configured for sending SNMP traps.
INT thresholdLev1DetectedValue	1.3.6.1.4.1.298.1.3.6.1.1.1.10	INTEGER	read-only	The value of the statistic for the last sampling period.
thresholdLev1Entry	1.3.6.1.4.1.298.1.3.6.1.1.1		not-accessible	Individual entry in threshold trap table.
INT thresholdLev1FallingEvent	1.3.6.1.4.1.298.1.3.6.1.1.1.12	INTEGER	read-write	How to respond to a triggered event for a falling event.
INT thresholdLev1GroupIndex	1.3.6.1.4.1.298.1.3.6.1.1.1.4	INTEGER	read-write	Group ID for trap set. One note--if the target is selected as hub, the group index will be ignored.
INT thresholdLev1Index	1.3.6.1.4.1.298.1.3.6.1.1.1.1	INTEGER	read-only	An index that uniquely identifies an entry in the alarm table.
INT thresholdLev1Interval	1.3.6.1.4.1.298.1.3.6.1.1.1.13	INTEGER	read-write	The interval in seconds over which the data is sampled.
OCT thresholdLev1OwnerString	1.3.6.1.4.1.298.1.3.6.1.1.1.14	OCTET STRING	read-write	8-byte octet reserved for the owner who defined this entry.
INT thresholdLev1PortIndex	1.3.6.1.4.1.298.1.3.6.1.1.1.5	INTEGER	read-write	Port number for trap set. One note--if the target is selected as hub, the port index will be ignored.
INT thresholdLev1RisingEvent	1.3.6.1.4.1.298.1.3.6.1.1.1.11	INTEGER	read-write	How to respond to a triggered event for a rising event.
INT thresholdLev1SampleType	1.3.6.1.4.1.298.1.3.6.1.1.1.7	INTEGER	read-write	The method of sampling the selected variable and calculating the value to be compared against the threshold.
INT thresholdLev1StartupAlarm	1.3.6.1.4.1.298.1.3.6.1.1.1.8	INTEGER	read-write	When the trap is triggered in relation to value set. When goes above (2), below (3), or changes at all from (4).
INT thresholdLev1Status	1.3.6.1.4.1.298.1.3.6.1.1.1.2	INTEGER	read-write	Status of entry in threshold/trap table.
INT thresholdLev1Subject	1.3.6.1.4.1.298.1.3.6.1.1.1.6	INTEGER	read-write	Variable checking for in trap. These are the type of frames that a trap will be verified against.
thresholdLev1Table	1.3.6.1.4.1.298.1.3.6.1.1		not-accessible	Threshold/trap table.
INT thresholdLev1Target	1.3.6.1.4.1.298.1.3.6.1.1.1.3	INTEGER	read-write	Set target for threshold definition. Either whole hub(2) or particular port (3).
INT thresholdLev1WaterMark	1.3.6.1.4.1.298.1.3.6.1.1.1.9	INTEGER	read-write	Counter of threshold.

RFC description

SNMP MIB for the legacy Asante AH1012 hub and Asante switch equipment, providing management definitions for older Asante network devices with SNMP support.

Start monitoring Asante AH1012 Ethernet hub (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ASANTE-AH1012-MIB

What Is ASANTE-AH1012-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description