ARRIS-C3-FPD-MIB

All MIBs › ARRIS-C3-FPD-MIB

Organization: Arris International

Last Updated: 2003-08-20

Category: DOCSIS and Cable, Vendor: ARRIS

Description: ARRIS C3 CMTS field programmable device firmware status and upgrade management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ARRIS-C3-FPD-MIB?

ARRIS-C3-FPD-MIB is an ARRIS proprietary MIB managing the Front Panel Display (FPD) on the ARRIS CMTS C3 (Cadant C3) cable modem termination system chassis. Its objects cover a message table (index, text) for the front-panel display, attached/detached status and notification traps, dual power-supply status, four temperature-status readings, six fan-status readings with configurable upper/lower speed limits, LCD contrast, LED status, and hardware/software revision. As a hardware-status MIB it lets an administrator watch fan and temperature status via the front-panel-display controller as an early-warning system for a CMTS chassis. It is deployed on the ARRIS CMTS C3 (Cadant C3) cable modem termination system. Engineers can download the ARRIS-C3-FPD-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ARRIS-C3-FPD-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ARRIS CMTS C3 (Cadant C3) cable modem termination system

Monitoring Examples

An administrator monitors dcxFPDTemp1Status through Temp4Status alongside the six fan-status objects to catch a CMTS C3 chassis cooling problem before it triggers a thermal shutdown.

What Can Be Monitored

front-panel display fan/temperature/power status

Imported Objects

From ARRIS-MIB

cmtsC3

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32
enterprises

How to Use in IPNetwork Monitor

Example using dcxFPDTemp1Status OID:

Select an ARRIS (Cadant) C3 CMT (Cable Modem Termination System) (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type dcxFPDTemp1Status into the Find box to locate it in the OID tree, then select it and click OK. Specifies the temperature reading for the sensor on the CPU card closest to the CPU. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the reported value exceeds the level expected for healthy operation, since sustained high temperature often precedes thermal shutdown or hardware degradation. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
cmtsC3FPDMIB	1.3.6.1.4.1.4115.1.4.3.3			This MIB manages the Front Panel Display (FPD) software on the Arris CMTS C3
dcxFPDObjects	1.3.6.1.4.1.4115.1.4.3.3.1
dcxFPDMsgTable	1.3.6.1.4.1.4115.1.4.3.3.1.1		not-accessible	Table of Front Panel LCD Messages.
dcxFPDMsgEntry	1.3.6.1.4.1.4115.1.4.3.3.1.1.1		not-accessible	.
U32 dcxFPDMsgIndex	1.3.6.1.4.1.4115.1.4.3.3.1.1.1.1	Unsigned32	not-accessible	Index used to order the FPD Messages.
OCT dcxFPDMsgString	1.3.6.1.4.1.4115.1.4.3.3.1.1.1.2	OCTET STRING	read-write	Specifies a string that can be displayed on the front panel.
dcxFPDControlGroup	1.3.6.1.4.1.4115.1.4.3.3.1.2
INT dcxFPDAttachedStatus	1.3.6.1.4.1.4115.1.4.3.3.1.2.1	INTEGER	read-only	Displays if the front panel display is attached to the Cmts or not.
INT dcxFPDPowerStatus1	1.3.6.1.4.1.4115.1.4.3.3.1.2.2	INTEGER	read-only	Specifies if the primary power supply is working. This is the rightmost power supply. The following values are possible: on(1) and off(2)
INT dcxFPDPowerStatus2	1.3.6.1.4.1.4115.1.4.3.3.1.2.3	INTEGER	read-only	Specifies if the secondary power supply is working. This is the leftmost power supply(nearest the fan tray). The following values are possible: on(1) and off(2)
I32 dcxFPDTemp1StatusEx	1.3.6.1.4.1.4115.1.4.3.3.1.2.4	Integer32	read-only	Specifies the temperature reading for the sensor on the CPU card closest to the CPU.
I32 dcxFPDTemp2Status	1.3.6.1.4.1.4115.1.4.3.3.1.2.5	Integer32	read-only	Specifies the temperature reading for the sensor on the CPU card, on the right hand side.
I32 dcxFPDTemp3Status	1.3.6.1.4.1.4115.1.4.3.3.1.2.6	Integer32	read-only	Specifies the temperature reading for the sensor on the Kanga card under the Roo cards between RX4 and RX5.
I32 dcxFPDTemp4Status	1.3.6.1.4.1.4115.1.4.3.3.1.2.7	Integer32	read-only	Specifies the temperature reading for the sensor on the Kanga card under the Roo cards between RX2 and RX3.
INT dcxFPDFan1Status	1.3.6.1.4.1.4115.1.4.3.3.1.2.8	INTEGER	read-only	Specifies the fan status for the fan nearest the front of the box. The following values are possible: Rotating(1) and BadRotating(2). BadRotating is set when the fan is operating outside of dcxFPDFanUpperLimit and dcxFPDFanLowerLimit.
INT dcxFPDFan2Status	1.3.6.1.4.1.4115.1.4.3.3.1.2.9	INTEGER	read-only	Specifies the fan status for the fan 2nd from the front. The following values are possible: Rotating(1) and BadRotating(2). BadRotating is set when the fan is operating outside of dcxFPDFanUpperLimit and dcxFPDFanLowerLimit.
INT dcxFPDFan3Status	1.3.6.1.4.1.4115.1.4.3.3.1.2.10	INTEGER	read-only	Specifies the fan status for the fan 3rd from the front. The following values are possible: Rotating(1) and BadRotating(2). BadRotating is set when the fan is operating outside of dcxFPDFanUpperLimit and dcxFPDFanLowerLimit.
INT dcxFPDFan4Status	1.3.6.1.4.1.4115.1.4.3.3.1.2.11	INTEGER	read-only	Specifies the fan status for the fan 4th from the front. The following values are possible: Rotating(1) and BadRotating(2). BadRotating is set when the fan is operating outside of dcxFPDFanUpperLimit and dcxFPDFanLowerLimit.
INT dcxFPDFan5Status	1.3.6.1.4.1.4115.1.4.3.3.1.2.12	INTEGER	read-only	Specifies the fan status for the fan 5th from the front. The following values are possible: Rotating(1) and BadRotating(2). BadRotating is set when the fan is operating outside of dcxFPDFanUpperLimit and dcxFPDFanLowerLimit.
INT dcxFPDFan6Status	1.3.6.1.4.1.4115.1.4.3.3.1.2.13	INTEGER	read-only	Specifies the fan status for the fan nearest the back of the box The following values are possible: Rotating(1) and BadRotating(2). BadRotating is set when the fan is operating outside of dcxFPDFanUpperLimit and dcxFPDFanLowerLimit.
I32 dcxFPDFanUpperLimit	1.3.6.1.4.1.4115.1.4.3.3.1.2.14	Integer32	read-write	Specifies the upper fan limit(Upper threshold of expected current draw)
I32 dcxFPDFanLowerLimit	1.3.6.1.4.1.4115.1.4.3.3.1.2.15	Integer32	read-write	Specifies the lower fan limit(Lower threshold of expected current draw)
I32 dcxFPDLCDContrast	1.3.6.1.4.1.4115.1.4.3.3.1.2.16	Integer32	read-write	Specifies the contrast level for the LCD
I32 dcxFPDLedSetStatus	1.3.6.1.4.1.4115.1.4.3.3.1.2.17	Integer32	read-write	Used to turn on or off a Led on the front panel
I32 dcxFPDHwRevision	1.3.6.1.4.1.4115.1.4.3.3.1.2.18	Integer32	read-only	Specifies the front panel h/w revision
I32 dcxFPDSwRevision	1.3.6.1.4.1.4115.1.4.3.3.1.2.19	Integer32	read-only	Specifies the front panel s/w revision
dcxFPDTrapGroup	1.3.6.1.4.1.4115.1.4.3.3.1.3
NTF dcxFPDAttached	1.3.6.1.4.1.4115.1.4.3.3.1.3.1			Front Panel Display has been attached.
NTF dcxFPDDetached	1.3.6.1.4.1.4115.1.4.3.3.1.3.2			Front Panel Display has been detached.
NTF dcxFPDFan1Fail	1.3.6.1.4.1.4115.1.4.3.3.1.3.3			Fan nearest the front of the box failed
NTF dcxFPDFan1FailClr	1.3.6.1.4.1.4115.1.4.3.3.1.3.4			Fan nearest the front of the box is working
NTF dcxFPDFan2Fail	1.3.6.1.4.1.4115.1.4.3.3.1.3.5			Fan 2nd from the front failed
NTF dcxFPDFan2FailClr	1.3.6.1.4.1.4115.1.4.3.3.1.3.6			Fan 2nd from the front is working
NTF dcxFPDFan3Fail	1.3.6.1.4.1.4115.1.4.3.3.1.3.7			Fan 3rd from the front failed
NTF dcxFPDFan3FailClr	1.3.6.1.4.1.4115.1.4.3.3.1.3.8			Fan 3rd from the front is working
NTF dcxFPDFan4Fail	1.3.6.1.4.1.4115.1.4.3.3.1.3.9			Fan 4th from the front failed
NTF dcxFPDFan4FailClr	1.3.6.1.4.1.4115.1.4.3.3.1.3.10			Fan 4th from the front is working
NTF dcxFPDFan5Fail	1.3.6.1.4.1.4115.1.4.3.3.1.3.11			Fan 5th from the front failed
NTF dcxFPDFan5FailClr	1.3.6.1.4.1.4115.1.4.3.3.1.3.12			Fan 5th from the front is working
NTF dcxFPDFan6Fail	1.3.6.1.4.1.4115.1.4.3.3.1.3.13			Fan nearest the back of the box failed
NTF dcxFPDFan6FailClr	1.3.6.1.4.1.4115.1.4.3.3.1.3.14			Fan nearest the back of the box is working
NTF dcxFPDPwr1Fail	1.3.6.1.4.1.4115.1.4.3.3.1.3.15			Rightmost power supply failed
NTF dcxFPDPwr1FailClr	1.3.6.1.4.1.4115.1.4.3.3.1.3.16			Rightmost power supply is working
NTF dcxFPDPwr2Fail	1.3.6.1.4.1.4115.1.4.3.3.1.3.17			Leftmost power supply failed
NTF dcxFPDPwr2FailClr	1.3.6.1.4.1.4115.1.4.3.3.1.3.18			Leftmost power supply is working
NTF dcxFPDTempOkay	1.3.6.1.4.1.4115.1.4.3.3.1.3.19			System temperature is OK
NTF dcxFPDTempBad	1.3.6.1.4.1.4115.1.4.3.3.1.3.20			System temperature is too hot!
NTF dcxFPDTempCritical	1.3.6.1.4.1.4115.1.4.3.3.1.3.21			System temperature is critical!!!, CMTS will shut itself down!!!!
dcxFPDConformance	1.3.6.1.4.1.4115.1.4.3.3.1.4
dcxFPDCompliances	1.3.6.1.4.1.4115.1.4.3.3.1.4.1
dcxFPDCompliance	1.3.6.1.4.1.4115.1.4.3.3.1.4.1.1			The compliance statement for devices that implement Arris C3 compliant FPD features
dcxFPDGroups	1.3.6.1.4.1.4115.1.4.3.3.1.4.2
dcxFPDMsgGroup	1.3.6.1.4.1.4115.1.4.3.3.1.4.2.1			Arris C3 FPD message group
dcxFPDControlConfGroup	1.3.6.1.4.1.4115.1.4.3.3.1.4.2.2			Arris C3 FPD Control group

RFC description

Front Panel Display software management for Arris CMTS C3 cable modem termination system.

Start monitoring ARRIS (Cadant) C3 CMTS (Cable Modem Termination System) (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ARRIS-C3-FPD-MIB