All MIBs › APPC-MIB
Organization: IETF SNA NAU MIB Working Group
Last Updated: 1995-12-15
Category: SNA and Legacy Protocols
Description: Defines managed objects for configuring, monitoring, and controlling network devices with SNA Advanced Program-to-Program Communication (APPC/LU 6.2) capabilities.
IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring APPC-MIB with a free 30-day trial of IPNetwork Monitor.
What Is APPC-MIB?
APPC-MIB is a vendor-neutral IETF-style MIB module for managing network devices that implement IBM's SNA Advanced Program-to-Program Communication (APPC/LU 6.2) protocol, commonly found in legacy mainframe-connected networking gear. It exposes configuration objects for administrative control (like admin status, resource control, and tracing) alongside operational-state counterparts that reflect the live running condition of the APPC control point. Objects such as appcCntrlAdminStat/appcCntrlOperStat let an administrator monitor whether APPC control is enabled and functioning, appcCntrlOperTrace and its parameters reveal whether protocol tracing is active for diagnostics, and appcUpTime tracks how long the APPC subsystem has been running — directly supporting software/service status monitoring. It builds on general SNMP framework conventions and is typically deployed alongside other SNA/APPN management MIBs on gateways bridging SNA and IP networks. Typical deployment context is legacy enterprise or financial-services environments still running SNA-based host connectivity through APPC-capable routers or protocol converters. Engineers implementing or auditing this functionality typically reference the APPC-MIB RFC/standard documentation for the authoritative specification.
IPNetwork Monitor allows you to monitor SNMP objects defined in APPC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- SNA/APPC gateway or protocol converter
- vendor-neutral, standards-based MIB, not tied to a specific manufacturer
Monitoring Examples
An administrator would poll appcCntrlOperStat against appcCntrlAdminStat to detect a mismatch indicating the APPC control point failed to come up as configured, and check appcUpTime to confirm the APPC subsystem hasn't unexpectedly restarted. appcCntrlOperTrace and appcCntrlOperTraceParm reveal whether diagnostic tracing was left running (a performance drag) versus the administratively requested appcCntrlAdminTrace state. appcCntrlOperRscvTime/appcCntrlOperStatTime give timestamps for the last state or resource-control change, useful for correlating APPC outages with other network events.
What Can Be Monitored
- APPC control point admin vs operational status
- APPC subsystem uptime
- trace enable state and parameters
- resource control state
- time of last status/resource change
This MIB depends on
Related MIBs
Imported Objects
From SNA-NAU-MIB
| snanauMIB | MODULE-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks | |
| mib-2 |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| InstancePointer | |
| TEXTUAL-CONVENTION |
How to Use in IPNetwork Monitor
Example using appcSessStatsSentFmdBytes OID:
Select an SNA/APPC gateway or protocol converter as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type appcSessStatsSentFmdBytes into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of function management data (FMD) bytes sent by the local LU. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| OCT appcActiveConvCorrelator | 1.3.6.1.2.1.34.3.1.5.1.1.7 | OCTET STRING | read-only | This is an 8-byte identifier that the source LU assigns to the conversation; the source LU is the one that sent the allocation request. The conversation correlator is included on the allocation request. The conversation correlator uniquely identifies a conversation, from among all conversations, between the local and partner LUs. It may be used, for example, during problem determination associated with a conversation. A length of 0 indicates that no conversation correlator is defined. |
| INT appcActiveConvDuplex | 1.3.6.1.2.1.34.3.1.5.1.1.10 | INTEGER | read-only | Indicates the conversation duplex style in effect for the conversation. half Indicates that information can be transferred in both directions, but only in one direction at a time. full Indicates that information can be transferred in both directions at the same time. |
| appcActiveConvEntry | 1.3.6.1.2.1.34.3.1.5.1.1 | not-accessible | Entry representing one active APPC Conversation. | |
| OCT appcActiveConvId | 1.3.6.1.2.1.34.3.1.5.1.1.4 | OCTET STRING | read-only | The 4-byte ID of the conversation. |
| STR appcActiveConvLocLuName | 1.3.6.1.2.1.34.3.1.5.1.1.1 | DisplayString | not-accessible | The SNA name of the local LU for the conversation. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. If this object has the same value as appcLluOperName, then the two entries being indexed apply to the same resource (specifically, to the same local LU). |
| OCT appcActiveConvLuwIdInstance | 1.3.6.1.2.1.34.3.1.5.1.1.19 | OCTET STRING | read-only | The instance identifier for the logical unit of work. |
| STR appcActiveConvLuwIdName | 1.3.6.1.2.1.34.3.1.5.1.1.18 | DisplayString | read-only | The SNA name of the LU that initiated the logical unit of work that is associated with this active TP. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the LU name if the NetId is present. |
| OCT appcActiveConvLuwIdSequence | 1.3.6.1.2.1.34.3.1.5.1.1.20 | OCTET STRING | read-only | The sequence identifier for the logical unit of work. |
| STR appcActiveConvModeName | 1.3.6.1.2.1.34.3.1.5.1.1.17 | DisplayString | read-only | The Mode Name used for this conversation. This is a 1-8 character name. |
| STR appcActiveConvParLuName | 1.3.6.1.2.1.34.3.1.5.1.1.2 | DisplayString | not-accessible | The SNA name of the partner LU for the conversation. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. If this object has the same value as appcLuPairOperParLuName, then the two entries being indexed apply to the same resource (specifically, to the same partner LU). |
| OCT appcActiveConvPcid | 1.3.6.1.2.1.34.3.1.5.1.1.16 | OCTET STRING | read-only | The procedure correlation identifier (PCID) of the session. It is an 8-octet value assigned by the control point providing session services for the primary LU. A null string indicates that the value is unknown. |
| STR appcActiveConvPcidNauName | 1.3.6.1.2.1.34.3.1.5.1.1.15 | DisplayString | read-only | The network-qualified NAU name of the node at which the session and PCID originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name. A null string indicates that the value is unknown. |
| C32 appcActiveConvRcvBytes | 1.3.6.1.2.1.34.3.1.5.1.1.13 | Counter32 | read-only | Indicates the number of bytes that was received on the conversation. The count includes all SNA RU bytes sent, including those in the FMH-5 (Attach), FMH-7 (Error Description), SIGNAL, LUSTAT, and SNA responses; it does not include SNA TH and RH bytes. |
| C32 appcActiveConvSendBytes | 1.3.6.1.2.1.34.3.1.5.1.1.12 | Counter32 | read-only | Indicates the number of bytes that was sent on the conversation. The count includes all SNA RU bytes sent, including those in the FMH-5 (Attach), FMH-7 (Error Description), SIGNAL, LUSTAT, and SNA responses; it does not include SNA TH and RH bytes. |
| I32 appcActiveConvSessIndex | 1.3.6.1.2.1.34.3.1.5.1.1.3 | Integer32 | not-accessible | Index of entry in appcActSessTable that is associated with this conversation. If this object has the same value as appcActSessIndex for the same LU pair, then the two entries being indexed apply to the same resource (specifically, to the same session). |
| INT appcActiveConvSource | 1.3.6.1.2.1.34.3.1.5.1.1.9 | INTEGER | read-only | Indicates whether the local or partner LU is the source of the conversation, that is, which LU started the conversation by sending the allocation request. localLu The local LU is the source of the conversation, and the partner LU is the target of the conversation. partnerLu The partner LU is the source of the conversation, and the local LU is the target of the conversation. |
| INT appcActiveConvState | 1.3.6.1.2.1.34.3.1.5.1.1.5 | INTEGER | read-only | Indicates the state of the conversation at the instant when the information was retrieved. The values are: reset The conversation is reset (i.e., deallocated). send The conversation can send data. This value also is returned if the conversation is in Send-Pending state. receive The conversation can receive data. confirm The conversation has received a confirm indicator. It can issue an [MC_]CONFIRMED or [MC_]SEND_ERROR verb to change state. It will continue in Receive state if an [MC_]CONFIRMED verb is issued. confirmSend The conversation is in Confirm state and changes to Send state when an [MC_]CONFIRMED verb is issued. confirmDealloc The conversation is in Confirm state and becomes inactive when an [MC_]CONFIRMED verb is issued. pendingDeallocate The conversation is in Pending-Deallocate state while it waits for (MC_)DEALLOCATE TYPE (sync_level) to complete. pendingPost The conversation is in Pending-Post state while it waits for the [MC_]RECEIVE_AND_POST verb to complete its receive function. sendReceive The full-duplex conversation can send or receive data. sendOnly The full-duplex conversation can send data, but it does not have permission to receive data, because the partner TP has already deallocated its side of the conversation. receiveOnly The full-duplex conversation can receive data, but it does not have permission to send data, because it has already deallocated its side of the conversation. deferReceive Waiting for a successful SYNCPT verb operation to go into the receive state. deferDeallocate Waiting for a successful SYNCPT verb operation to go into the reset state. syncpoint Need to response to a SYNCPT verb issued. After successful operation, the next state will be receive. syncpointSend Need to response to a SYNCPT verb issued. After successful operation, the next state will be send. syncpointDeallocate Need to response to a SYNCPT verb issued. After successful operation, the next state will be reset. backoutRequired TP must execute a BACKOUT verb to backout the transaction. |
| INT appcActiveConvSyncLvl | 1.3.6.1.2.1.34.3.1.5.1.1.8 | INTEGER | read-only | Indicates the highest sync level support for the conversation. The values are: none Indicates that no sync-level processing can be performed on this conversation. The transaction program does not issue verbs or recognize any returned parameters relating to any sync-level function. confirm Indicates that confirmation processing can be performed on this conversation. The transaction program can issue verbs and recognize returned parameters relating to confirmation. syncpt Indicates that syncpt and confirmation processing can be performed on this conversation. The transaction program can issue verbs and recognize returned parameters relating to syncpt and confirmation. |
| appcActiveConvTable | 1.3.6.1.2.1.34.3.1.5.1 | not-accessible | Table of information about active APPC Conversations. In this context 'active' means that a conversation is currently associated with a particular session. Two entries are present in the table when both LUs for the session are local. | |
| STR appcActiveConvTpName | 1.3.6.1.2.1.34.3.1.5.1.1.21 | DisplayString | read-only | The transaction program name which started this conversation. This name could either be from a FMH5 ATTACH for a remotely started conversation, otherwise it could the name of the local TP if available. When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non- displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes). This name is NULL if the conversation is started locally (i.e., not with a FMH5 ATTACH). |
| INT appcActiveConvType | 1.3.6.1.2.1.34.3.1.5.1.1.6 | INTEGER | read-only | Indicates the type of conversation. The values are: basic Indicates that this conversation supports basic verbs. mapped Indicates that this conversation supports mapped verbs. |
| TIK appcActiveConvUpTime | 1.3.6.1.2.1.34.3.1.5.1.1.11 | TimeTicks | read-only | The length of time since the conversation started, measured in hundredths of a second. |
| STR appcActiveConvUserid | 1.3.6.1.2.1.34.3.1.5.1.1.14 | DisplayString | read-only | The user ID that the initiating program provided in the incoming attach. |
| G32 appcActiveHprSessions | 1.3.6.1.2.1.34.3.1.1.3.11 | Gauge32 | read-only | Specifies the total number of active HPR APPC sessions. |
| G32 appcActiveSessions | 1.3.6.1.2.1.34.3.1.1.3.10 | Gauge32 | read-only | Specifies the total number of active APPC sessions supported by this implementation. Sessions for which both LUs are local are counted twice. |
| STR appcActSessCosName | 1.3.6.1.2.1.34.3.1.4.1.1.8 | DisplayString | read-only | The Class of Service (COS) name used for this session. A null string indicates that the value is unknown. |
| INT appcActSessEnhanceSecSup | 1.3.6.1.2.1.34.3.1.4.1.1.10 | INTEGER | read-only | Enhanced security supported. Indicates the level of enhanced security support: 1 = none 2 = level 1 3 = level 2 |
| appcActSessEntry | 1.3.6.1.2.1.34.3.1.4.1.1 | not-accessible | Entry of APPC Session Information Table. Indexed by LU pair and integer-valued session index. | |
| I32 appcActSessIndex | 1.3.6.1.2.1.34.3.1.4.1.1.3 | Integer32 | not-accessible | This value identifies the index of the session, which is unique for this LU pair. It is recommended that an Agent not reuse the index of a deactivated session for a significant period of time (e.g., one week). |
| INT appcActSessInUse | 1.3.6.1.2.1.34.3.1.4.1.1.18 | INTEGER | read-only | Specifies whether the session is currently in use (i.e., in bracket with a conversation). |
| NUM appcActSessLinkIndex | 1.3.6.1.2.1.34.3.1.4.1.1.27 | InstancePointer | read-only | This value identifies the link over which the session passes. This value points to the row in the table containing information on the link instance. (e.g., the sdlcLSAdminTable of the SNA DLC MIB module). This object may be NULL if the link is not specified or if a link is not applicable (as for APPN-level nodes). |
| STR appcActSessLocLuName | 1.3.6.1.2.1.34.3.1.4.1.1.1 | DisplayString | not-accessible | Specifies the name of the local LU for the session. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. If this object has the same value as appcLluOperName, then the two entries being indexed apply to the same resource (specifically, to the same local LU). |
| INT appcActSessMaxRcvRuSize | 1.3.6.1.2.1.34.3.1.4.1.1.20 | INTEGER | read-only | The maximum RU size used on this session for receiving RUs. |
| INT appcActSessMaxSndRuSize | 1.3.6.1.2.1.34.3.1.4.1.1.19 | INTEGER | read-only | The maximum RU size used on this session for sending RUs. |
| STR appcActSessModeName | 1.3.6.1.2.1.34.3.1.4.1.1.7 | DisplayString | read-only | The mode name used for this session. |
| INT appcActSessOperState | 1.3.6.1.2.1.34.3.1.4.1.1.23 | INTEGER | read-write | The value indicates the current operational state of the session. 'unbound (1)' - session has been unbound; in this state it will be removed from the session table by the Agent. 'pendingBind (2)' - this state has different meanings for dependent and independent LUs; for dependent LU - waiting for BIND from the host, for independent LU - waiting for BIND response. When a session enters this state, the corresponding entry in the session table is created by the Agent. 'bound (3)' - session has been successfully bound. 'pendingUnbind (4)' - session enters this state when an UNBIND is sent and before the rsp(UNBIND) is received. Session deactivation: If a session is in the operational state 'bound (3)' then setting the value of this object to 'unbound (1)' will initiate the session shutdown. If a session is in the operational state 'pendingBind (2)' then setting the value of this object to 'unbound (1)' will initiate the session shutdown. If a session is in the operational state 'pendingUnbind (4)' for an abnormally long period of time (e.g., three minutes) then setting the value of this object to 'unbound (1)' will change the session operational state to 'unbound (1)'. |
| STR appcActSessParLuName | 1.3.6.1.2.1.34.3.1.4.1.1.2 | DisplayString | not-accessible | Specifies the name of the partner LU for the session. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. If this object has the same value as appcLuPairOperParLuName, then the two entries being indexed apply to the same resource (specifically, to the same partner LU). |
| OCT appcActSessPcid | 1.3.6.1.2.1.34.3.1.4.1.1.5 | OCTET STRING | read-only | The procedure correlation identifier (PCID) of a session. It is an 8-octet value assigned by the control point providing session services for the primary LU. A null string indicates that the value is unknown. |
| STR appcActSessPcidCpName | 1.3.6.1.2.1.34.3.1.4.1.1.4 | DisplayString | read-only | The network-qualified CP name of the node at which the session and PCID originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name. A null string indicates that the value is unknown. |
| INT appcActSessPluIndicator | 1.3.6.1.2.1.34.3.1.4.1.1.6 | INTEGER | read-only | Indicates which LU is the PLU for this session. For independent LUs, the PLU (primary LU) is the one that initiated the session (sent BIND), while the SLU (secondary LU) is the one that accepted the session initiation (received BIND). The 'local' LU is the one identified by appcLluOperName. The 'partner' LU is the one identified by appcLuPairOperParLuName. |
| INT appcActSessRcvPacingSize | 1.3.6.1.2.1.34.3.1.4.1.1.22 | INTEGER | read-only | The size of the receive pacing window on this session. |
| G32 appcActSessRecvNxWndwSize | 1.3.6.1.2.1.34.3.1.4.1.1.16 | Gauge32 | read-only | The size of the next window which will be used to receive data. |
| INT appcActSessRecvPacingType | 1.3.6.1.2.1.34.3.1.4.1.1.14 | INTEGER | read-only | The type of pacing being used for receiving data. |
| G32 appcActSessRecvRpc | 1.3.6.1.2.1.34.3.1.4.1.1.15 | Gauge32 | read-only | The receive residual pace count. This represents the number of MUs that can still be received in the current session window. |
| OCT appcActSessRscv | 1.3.6.1.2.1.34.3.1.4.1.1.17 | OCTET STRING | read-only | The route selection control vector (RSCV CV2B) used for this session. It is present for APPN-level implementations. LEN-level implementations will return a null string. The internal format of this vector is described in SNA Formats. This object contains an uninterpreted copy of the control vector (including the length and key fields). |
| OCT appcActSessRtpNceId | 1.3.6.1.2.1.34.3.1.4.1.1.25 | OCTET STRING | read-only | The local HPR Network Connection Endpoint of the session. |
| OCT appcActSessRtpTcid | 1.3.6.1.2.1.34.3.1.4.1.1.26 | OCTET STRING | read-only | The local RTP connection TCID of the session. |
| G32 appcActSessSendNxWndwSize | 1.3.6.1.2.1.34.3.1.4.1.1.13 | Gauge32 | read-only | The size of the next window which will be used to send data. |
| INT appcActSessSendPacingType | 1.3.6.1.2.1.34.3.1.4.1.1.11 | INTEGER | read-only | The type of pacing being used for sending data. |
| G32 appcActSessSendRpc | 1.3.6.1.2.1.34.3.1.4.1.1.12 | Gauge32 | read-only | The send residual pace count. This represents the number of MUs that can still be sent in the current session window. |
| INT appcActSessSndPacingSize | 1.3.6.1.2.1.34.3.1.4.1.1.21 | INTEGER | read-only | The size of the send pacing window on this session. |
| appcActSessTable | 1.3.6.1.2.1.34.3.1.4.1 | not-accessible | Table of active APPC sessions. Two entries are present in the table when both session partners are local. | |
| INT appcActSessTransPriority | 1.3.6.1.2.1.34.3.1.4.1.1.9 | INTEGER | read-only | The transmission priority of this session. 1 = unknown priority 2 = low priority 3 = medium priority 4 = high priority 5 = network priority |
| TIK appcActSessUpTime | 1.3.6.1.2.1.34.3.1.4.1.1.24 | TimeTicks | read-only | The length of time the session has been active, measured in hundredths of a second. |
| INT appcCnosCommand | 1.3.6.1.2.1.34.3.1.1.4.1 | INTEGER | read-write | Specifies the CNOS command or verb to issue. First set the values of the particular CNOS parameter objects (from the range { appcCnosControl 2 } through { appcCnosControl 8 }) that apply to the CNOS command to be executed, set the three CNOS target objects ({ appcCnosControl 9 } through { appcCnosControl 11 }), then set this object to the command to be executed. Here is the list of parameter objects that must be set for each of the CNOS commands: INIT_SESSION_LIMIT - appcCnosMaxSessLimit appcCnosMinCwinLimit appcCnosMinClosLimit appcCnosTargetLocLuName appcCnosTargetParLuName appcCnosTargetModeName CHANGE_SESSION_LIMIT - appcCnosMaxSessLimit appcCnosMinCwinLimit appcCnosMinClosLimit appcCnosResponsible appcCnosTargetLocLuName appcCnosTargetParLuName appcCnosTargetModeName RESET_SESSION_LIMIT - appcCnosResponsible appcCnosDrainPart appcCnosForce appcCnosTargetLocLuName appcCnosTargetParLuName appcCnosTargetModeName |
| appcCnosConfGroup | 1.3.6.1.2.1.34.3.2.2.8 | A collection of objects providing the instrumentation of APPC CNOS processing. | ||
| appcCnosControl | 1.3.6.1.2.1.34.3.1.1.4 | |||
| INT appcCnosDrainPart | 1.3.6.1.2.1.34.3.1.1.4.6 | INTEGER | read-write | Specifies whether the partner LU is draining its conversations for this mode. When a mode session limit is reset (via a CNOS RESET_SESSION_LIMIT request), the partner LU could be set to process all queued conversations before deactivating all of the sessions (using the SNA Bracket Initiation Stop or BIS protocol). This parameter should be set to the desired value before setting the command (appcCnosCommand). This parameter applies only to the RESET_SESSION_LIMIT verb. |
| INT appcCnosDrainSelf | 1.3.6.1.2.1.34.3.1.1.4.5 | INTEGER | read-write | Specifies whether the local LU is draining its conversations for this mode. When a mode session limit is reset (via a CNOS RESET_SESSION_LIMIT request), the local LU could be set to process all queued conversations before deactivating all of the sessions (using the SNA Bracket Initiation Stopped or BIS protocol). This parameter should be set to the desired value before setting the command (appcCnosCommand). This parameter applies only to the RESET_SESSION_LIMIT verb. |
| INT appcCnosForce | 1.3.6.1.2.1.34.3.1.1.4.8 | INTEGER | read-write | Specifies whether the local LU should force the resetting of the session limit when certain error conditions occur that prevent the successful exchange of CNOS request and reply. This parameter should be set to the desired value before setting the command (appcCnosCommand). This parameter applies only to the RESET_SESSION_LIMIT verb. |
| I32 appcCnosMaxSessLimit | 1.3.6.1.2.1.34.3.1.1.4.2 | Integer32 | read-write | Specifies the maximum value that the local LU is to use, during CNOS processing, for the session limit. The local LU, as a target LU, will negotiate a higher session limit it receives in the CNOS request down to this maximum value. The local LU, as a source LU, will restrict the session limit it sends in a CNOS request to a value less than or equal to this maximum value. If set (i.e., greater than 0), this overrides the maximum session limit defined in the appcModeAdminTable. This parameter should be set to the desired value before setting the command (appcCnosCommand). This parameter applies to the INITIALIZE_SESSION_LIMIT and CHANGE_SESSION_LIMIT verbs. |
| I32 appcCnosMinClosLimit | 1.3.6.1.2.1.34.3.1.1.4.4 | Integer32 | read-write | Specifies the default minimum contention loser sessions limit. This parameter should be set to the desired value before setting the command (appcCnosCommand). This parameter applies to the INITIALIZE_SESSION_LIMIT and CHANGE_SESSION_LIMIT verbs. |
| I32 appcCnosMinCwinLimit | 1.3.6.1.2.1.34.3.1.1.4.3 | Integer32 | read-write | Specifies the default minimum contention winner sessions limit. This parameter should be set to the desired value before setting the command (appcCnosCommand). This parameter applies to the INITIALIZE_SESSION_LIMIT and CHANGE_SESSION_LIMIT verbs. |
| INT appcCnosResponsible | 1.3.6.1.2.1.34.3.1.1.4.7 | INTEGER | read-write | Specifies which LU is responsible for selecting and deactivating sessions as a result of a change that decreases the session limit or the maximum number of contention winner sessions for the source or target LU. If no session need to be deactivated, this parameter is ignored. source - specifies that the source (local) LU is responsible. The target (partner) LU cannot negotiate this value. target - specifies that the target (partner) LU is responsible. The target LU can negotiate this value to source. This parameter should be set to the desired value before setting the command (appcCnosCommand). This parameter applies to the RESET_SESSION_LIMIT and CHANGE_SESSION_LIMIT verbs. |
| STR appcCnosTargetLocLuName | 1.3.6.1.2.1.34.3.1.1.4.9 | DisplayString | read-write | The SNA name of the local LU to which the CNOS command is to be applied. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. This object should be set to the desired value before setting the command (appcCnosCommand). This parameter applies to all CNOS verbs. |
| STR appcCnosTargetModeName | 1.3.6.1.2.1.34.3.1.1.4.11 | DisplayString | read-write | Specifies the mode name to which the CNOS command is to be applied. This object should be set to the desired value before setting the command (appcCnosCommand). This parameter applies to all CNOS verbs. |
| STR appcCnosTargetParLuName | 1.3.6.1.2.1.34.3.1.1.4.10 | DisplayString | read-write | The SNA name of the partner LU to which the CNOS command is to be applied. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. This object should be set to the desired value before setting the command (appcCnosCommand). This parameter applies to all CNOS verbs. |
| appcCntrlAdminGroup | 1.3.6.1.2.1.34.3.1.1.1 | |||
| INT appcCntrlAdminRscv | 1.3.6.1.2.1.34.3.1.1.1.2 | INTEGER | read-write | Indicates the desired state of RSCV information collection: notActive collection of route selection control vectors is not active. active collection of route selection control vectors is active. |
| INT appcCntrlAdminStat | 1.3.6.1.2.1.34.3.1.1.1.1 | INTEGER | read-write | Indicates the desired state of statistics collection: notActive collection of counters is not active. active collection of counters is active. When this object is set to notActive, all of the entries are removed from the appcSessStatsTable. |
| INT appcCntrlAdminTrace | 1.3.6.1.2.1.34.3.1.1.1.3 | INTEGER | read-write | Indicates the desired state of tracing: notActive collection of tracing information is not active active collection of tracing information is active |
| STR appcCntrlAdminTraceParm | 1.3.6.1.2.1.34.3.1.1.1.4 | DisplayString | read-write | Specifies the parameter to be used in conjunction with activating tracing. The actual content is implementation dependent. |
| appcCntrlOperGroup | 1.3.6.1.2.1.34.3.1.1.2 | |||
| INT appcCntrlOperRscv | 1.3.6.1.2.1.34.3.1.1.2.3 | INTEGER | read-only | Indicates the current collection options in effect: notActive collection of route selection control vectors is not active. active collection of route selection control vectors is active. |
| TIK appcCntrlOperRscvTime | 1.3.6.1.2.1.34.3.1.1.2.4 | TimeTicks | read-only | Time since the appcCntrlOperRscv object last changed. This time is in hundreds of a second. |
| INT appcCntrlOperStat | 1.3.6.1.2.1.34.3.1.1.2.1 | INTEGER | read-only | Indicates the current collection options in effect: notActive collection of counters is not active. active collection of counters is active. Statistical entries are present in the appcSessStatsTable only when the value of this object is 'active'. |
| TIK appcCntrlOperStatTime | 1.3.6.1.2.1.34.3.1.1.2.2 | TimeTicks | read-only | Time since the appcCntrlOperStat object last changed. This time is in hundreds of a second. |
| INT appcCntrlOperTrace | 1.3.6.1.2.1.34.3.1.1.2.5 | INTEGER | read-only | Indicates the current state of tracing: notActive collection of tracing information is not active. active collection of tracing information is active. |
| STR appcCntrlOperTraceParm | 1.3.6.1.2.1.34.3.1.1.2.7 | DisplayString | read-only | Specifies the parameter used in conjunction with activating tracing. The actual content is implementation dependent. |
| TIK appcCntrlOperTraceTime | 1.3.6.1.2.1.34.3.1.1.2.6 | TimeTicks | read-only | Time since the appcCntrlOperTrace object last changed. This time is in hundreds of a second. |
| appcCompliance | 1.3.6.1.2.1.34.3.2.1.1 | The compliance statement for the SNMPv2 entities which implement the APPC MIB. | ||
| appcCompliances | 1.3.6.1.2.1.34.3.2.1 | |||
| appcConformance | 1.3.6.1.2.1.34.3.2 | |||
| appcControlConfGroup | 1.3.6.1.2.1.34.3.2.2.7 | A collection of objects providing the instrumentation of APPC control. | ||
| appcConversation | 1.3.6.1.2.1.34.3.1.5 | |||
| appcConversationConfGroup | 1.3.6.1.2.1.34.3.2.2.10 | A collection of objects providing the instrumentation of APPC conversations. | ||
| appcCPIC | 1.3.6.1.2.1.34.3.1.6 | |||
| appcCpicAdminEntry | 1.3.6.1.2.1.34.3.1.6.1.1 | not-accessible | Entry of APPC CPI-C side information Table. | |
| STR appcCpicAdminLocLuName | 1.3.6.1.2.1.34.3.1.6.1.1.1 | DisplayString | not-accessible | The SNA name of the local LU to which this CPI-C side information definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. The reserved value '*ALL' indicates that the definition applies to all local LUs, and not just to a single local LU. |
| STR appcCpicAdminModeName | 1.3.6.1.2.1.34.3.1.6.1.1.5 | DisplayString | read-only | Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters). |
| STR appcCpicAdminParLuAlias | 1.3.6.1.2.1.34.3.1.6.1.1.3 | DisplayString | read-only | A local alias for the partner LU. If not known or not applicable, this object contains a zero-length string. |
| STR appcCpicAdminParLuName | 1.3.6.1.2.1.34.3.1.6.1.1.4 | DisplayString | read-only | The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. |
| INT appcCpicAdminSecurity | 1.3.6.1.2.1.34.3.1.6.1.1.9 | INTEGER | read-only | Specifies the security information to be used for allocating the conversation. none - No security information. same - Use the security environment currently associated with this TP. pgm - Use the program-supplied user_id and password. pgmStrong - Use the program-supplied user_id and password. The local LU will insure that the password is not exposed in clear-text form on the physical network. distributed - Use the security environment and a distributed security system to generate the authentication information for this request. If distributed security tokens cannot be generated, then fail the conversation. mutual - Authenticate both the user to the destination system and the destination system to the user. |
| STR appcCpicAdminSymbDestName | 1.3.6.1.2.1.34.3.1.6.1.1.2 | DisplayString | not-accessible | Specifies the symbolic destination name used by CPI-C applications to identify this definition. |
| appcCpicAdminTable | 1.3.6.1.2.1.34.3.1.6.1 | not-accessible | APPC CPI-C side information table. | |
| STR appcCpicAdminTpName | 1.3.6.1.2.1.34.3.1.6.1.1.7 | DisplayString | read-only | Specifies the name of the partner TP to be used when a CPI-C application initiates a conversation specifying this side information entry. Display convention When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes). |
| INT appcCpicAdminTpNameType | 1.3.6.1.2.1.34.3.1.6.1.1.6 | INTEGER | read-only | Specifies whether the TP name in appcCpicAdminTpName identifies a normal TP or an SNA service TP. In this context, a normal TP is one with a name consisting only of displayable characters, while an SNA service TP has a name containing octets that do not map to displayable characters. |
| STR appcCpicAdminUserid | 1.3.6.1.2.1.34.3.1.6.1.1.8 | DisplayString | read-only | The security userid, if any, associated with the side information definition. |
| appcCpicConfGroup | 1.3.6.1.2.1.34.3.2.2.9 | A collection of objects providing the instrumentation of APPC CPI-C side information. | ||
| appcCpicOperEntry | 1.3.6.1.2.1.34.3.1.6.2.1 | not-accessible | Entry of APPC CPI-C side information Table. | |
| STR appcCpicOperLocLuName | 1.3.6.1.2.1.34.3.1.6.2.1.1 | DisplayString | not-accessible | The SNA name of the local LU to which this CPI-C side information definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. The reserved value '*ALL' indicates that the definition applies to all local LUs, and not just to a single local LU. |
| STR appcCpicOperModeName | 1.3.6.1.2.1.34.3.1.6.2.1.5 | DisplayString | read-only | Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters). |
| STR appcCpicOperParLuAlias | 1.3.6.1.2.1.34.3.1.6.2.1.3 | DisplayString | read-only | A local alias for the partner LU. If not known or not applicable, this object contains a zero-length string. |
| STR appcCpicOperParLuName | 1.3.6.1.2.1.34.3.1.6.2.1.4 | DisplayString | read-only | The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. |
| INT appcCpicOperSecurity | 1.3.6.1.2.1.34.3.1.6.2.1.9 | INTEGER | read-only | Specifies the security information to be used for allocating the conversation. none - No security information. same - Use the security environment currently associated with this TP. pgm - Use the program-supplied user_id and password. pgmStrong - Use the program-supplied user_id and password. The local LU will insure that the password is not exposed in clear-text form on the physical network. distributed - Use the security environment and a distributed security system to generate the authentication information for this request. If distributed security tokens cannot be generated, then fail the conversation. mutual - Authenticate both the user to the destination system and the destination system to the user. |
| STR appcCpicOperSymbDestName | 1.3.6.1.2.1.34.3.1.6.2.1.2 | DisplayString | not-accessible | Specifies the symbolic destination name used by CPI-C applications to identify this definition. |
| appcCpicOperTable | 1.3.6.1.2.1.34.3.1.6.2 | not-accessible | APPC CPI-C side information operational table. | |
| STR appcCpicOperTpName | 1.3.6.1.2.1.34.3.1.6.2.1.7 | DisplayString | read-only | Specifies the name of the partner TP to be used when a CPI-C application initiates a conversation specifying this side information entry. Display convention When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes). |
| INT appcCpicOperTpNameType | 1.3.6.1.2.1.34.3.1.6.2.1.6 | INTEGER | read-only | Specifies whether the TP name in appcCpicOperTpName identifies a normal TP or an SNA service TP. In this context, a normal TP is one with a name consisting only of displayable characters, while an SNA service TP has a name containing octets that do not map to displayable characters. |
| STR appcCpicOperUserid | 1.3.6.1.2.1.34.3.1.6.2.1.8 | DisplayString | read-only | The security userid, if any, associated with the active side information definition. |
| STR appcDefaultFileSpec | 1.3.6.1.2.1.34.3.1.1.3.6 | DisplayString | read-only | The local file specification that is to be searched by the APPC attach manager when no DEFINE_TP verb has been issued for the TP name received on an incoming attach. In this case, the attach manager will attempt to start a program whose file name is the same as the incoming TP name. If found, the program is loaded. If not found, the attach is rejected. The value '*' indicates that the normal search path for executable programs is to be used for locating an undefined transaction program. A null string indicates that there is no default file specification for undefined transaction programs. |
| INT appcDefaultImplInbndPlu | 1.3.6.1.2.1.34.3.1.1.3.4 | INTEGER | read-only | Specifies whether or not inbound implicit partner LU support is enabled. The following values are defined: no - Specifies that inbound implicit partner LU support is disabled, which means that an incoming bind that specifies a partner LU that is not defined at the local node will be rejected. yes - Specifies that inbound implicit partner LU support is enabled, which provides the capability to accept an incoming BIND request that contains a partner LU name that is not defined at the local node. |
| STR appcDefaultLuName | 1.3.6.1.2.1.34.3.1.1.3.3 | DisplayString | read-only | Specifies the name of the local LU that is to serve as the default LU. This is the default LU to which are routed inbound BIND requests that exclude the secondary LU name. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. This local LU name must match a defined entry in the appcLluAdminTable. |
| I32 appcDefaultMaxMcLlSndSize | 1.3.6.1.2.1.34.3.1.1.3.5 | Integer32 | read-only | Specifies the maximum size of a logical record to be used for a mapped conversation when sending data to either the inbound or outbound implicit partner LU. This size is the maximum number of bytes in a single logical record, as indicated in the LL field of the record. The default value is 32767. Note that this object does not limit the maximum size that an application program can supply on the Send Data call for a mapped conversation. |
| STR appcDefaultModeName | 1.3.6.1.2.1.34.3.1.1.3.2 | DisplayString | read-only | Specifies the mode name to be used under the following conditions: When an incoming BIND request contains a mode name not defined at the local node. The parameters defined for this mode are used for the inbound implicit mode capability. When an APPC program issues an [MC_]ALLOCATE, [MC_]SEND_CONVERSATION, or CNOS verb, or when a CPI-C program issues an Allocate (CMALLC) call, specifying a mode name not defined at the local node. The parameters defined for this mode are used for the outbound implicit mode capability. This mode name must match a defined entry in the appcModeAdminTable. |
| INT appcDefaultTpConvSecRqd | 1.3.6.1.2.1.34.3.1.1.3.8 | INTEGER | read-only | Specifies whether or not conversation security will be used for default TPs. no - Specifies that the incoming attach does not have to contain security information. yes - Specifies that the incoming attach must contain valid authentication information (e.g., user ID and password). |
| INT appcDefaultTpOperation | 1.3.6.1.2.1.34.3.1.1.3.7 | INTEGER | read-only | Specifies how the program will be started. other - Specifies that the default TP operation is none of the methods specified below. It may be a product-specific method. queuedOperatorStarted - Specifies that one version of the program will be run at a time. If an incoming attach arrives and the program has not been started yet, APPC will issue a message to the operator to start the specified program. Subsequent attaches that arrive while the program is active will be queued. queuedOperatorPreloaded - Specifies that one version of the program will be run at a time. If an incoming attach arrives and the program has not been started yet, the Attach will be rejected. The APPC attach manager determines that a TP has started upon reception of an APPC RECEIVE_ALLOCATE verb, or a CPI-C Accept_Conversation (CMACCP) or Specify_Local_TP_Name (CMSLTP) call. No message is sent to the operator. Subsequent attaches that arrive while the program is active are queued. queuedAmStarted - Specifies that one version of the program will be run at a time and will be started by the APPC attach manager. Subsequent attaches that arrive while the program is active will be queued. nonqueuedAmStarted - Specifies that multiple copies of the program will be run at a time and will be started by the APPC attach manager. |
| appcGlobal | 1.3.6.1.2.1.34.3.1.1 | |||
| appcGlobalConfGroup | 1.3.6.1.2.1.34.3.2.2.1 | A collection of objects providing the instrumentation of APPC global information and defaults. | ||
| appcGlobalObjects | 1.3.6.1.2.1.34.3.1.1.3 | |||
| appcGroups | 1.3.6.1.2.1.34.3.2.2 | |||
| INT appcHistConvEndedBy | 1.3.6.1.2.1.34.3.1.5.2.1.10 | INTEGER | read-only | Indicates which LU ended the conversation. |
| DAT appcHistConvEndTime | 1.3.6.1.2.1.34.3.1.5.2.1.2 | DateAndTime | read-only | The time at which the conversation ended. |
| appcHistConvEntry | 1.3.6.1.2.1.34.3.1.5.2.1 | not-accessible | Entry representing one APPC Conversation. | |
| I32 appcHistConvIndex | 1.3.6.1.2.1.34.3.1.5.2.1.1 | Integer32 | not-accessible | Index for entry in Conversation table. This value identifies the unique index of the conversation. It is recommended that an Agent not reuse the index of a deactivated conversation for a significant period of time (e.g. one week). |
| STR appcHistConvLocLuName | 1.3.6.1.2.1.34.3.1.5.2.1.3 | DisplayString | read-only | The name of the local LU for this conversation. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. |
| OCT appcHistConvLogData | 1.3.6.1.2.1.34.3.1.5.2.1.9 | OCTET STRING | read-only | The first 32 bytes of the data portion of the Log Data GDS Variable that is associated with the last FMH-7 that occurred on this conversation. If there was no Log Data GDS Variable associated with the FMH-7, this object is null. This object reflects only the data portion of the Log Data GDS Variable (i.e. not the LL or GDS Id). |
| STR appcHistConvParLuName | 1.3.6.1.2.1.34.3.1.5.2.1.4 | DisplayString | read-only | The SNA name of the partner LU for the conversation. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. |
| OCT appcHistConvPcid | 1.3.6.1.2.1.34.3.1.5.2.1.7 | OCTET STRING | read-only | The procedure correlation identifier (PCID) of the session. It is an 8-octet value assigned by the control point providing session services for the primary LU. A null string indicates that the value is unknown. |
| STR appcHistConvPcidNauName | 1.3.6.1.2.1.34.3.1.5.2.1.6 | DisplayString | read-only | The network-qualified NAU name of the node at which the session and PCID originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name. A null string indicates that the value is unknown. |
| SNA appcHistConvSenseData | 1.3.6.1.2.1.34.3.1.5.2.1.8 | SnaSenseData | read-only | The sense data associated with the action that ended this conversation, e.g., FMH-7 or UNBIND. |
| appcHistConvTable | 1.3.6.1.2.1.34.3.1.5.2 | not-accessible | Table of historical information about APPC Conversations that ended in error. Possible categories of error conditions that could be saved in this table are: - allocation errors, - deallocate abend, - program errors, and - service errors. | |
| STR appcHistConvTpName | 1.3.6.1.2.1.34.3.1.5.2.1.5 | DisplayString | read-only | The transaction program name which started this conversation. This name could either be from a FMH5 ATTACH for a remotely started conversation, otherwise it could the name of the local TP if available. When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non- displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes). This name is NULL if the conversation is started locally (i.e., not with a FMH5 ATTACH). |
| STR appcHistSessComponentId | 1.3.6.1.2.1.34.3.1.4.3.1.9 | DisplayString | read-only | The implementation-specific name of the component which detected the problem. |
| STR appcHistSessDetectModule | 1.3.6.1.2.1.34.3.1.4.3.1.10 | DisplayString | read-only | The implementation-specific name of the module which detected the problem. |
| appcHistSessEntry | 1.3.6.1.2.1.34.3.1.4.3.1 | not-accessible | Entry of APPC Session History Table. This table is indexed by an integer which is continuously incremented until it eventually wraps. | |
| INT appcHistSessIndex | 1.3.6.1.2.1.34.3.1.4.3.1.1 | INTEGER | not-accessible | Table index. The value of the index begins at zero and is incremented up to a maximum value of 2**31-1 (2,147,483,647) before wrapping. |
| STR appcHistSessLocLuName | 1.3.6.1.2.1.34.3.1.4.3.1.4 | DisplayString | read-only | The network-qualified local LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. |
| STR appcHistSessModeName | 1.3.6.1.2.1.34.3.1.4.3.1.6 | DisplayString | read-only | The mode name of the session. |
| STR appcHistSessParLuName | 1.3.6.1.2.1.34.3.1.4.3.1.5 | DisplayString | read-only | The network-qualified partner LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. |
| SNA appcHistSessSenseData | 1.3.6.1.2.1.34.3.1.4.3.1.8 | SnaSenseData | read-only | The sense data associated with the termination of the session, taken from the negative BIND response or UNBIND request. |
| appcHistSessTable | 1.3.6.1.2.1.34.3.1.4.3 | not-accessible | Table of historical information about APPC sessions that terminated abnormally. Two entries may be present in the table when both session partners are local. It is an implementation choice how long to retain information about a given session. | |
| DAT appcHistSessTime | 1.3.6.1.2.1.34.3.1.4.3.1.2 | DateAndTime | read-only | The time at which the session was either terminated or failed to be established. |
| INT appcHistSessType | 1.3.6.1.2.1.34.3.1.4.3.1.3 | INTEGER | read-only | Indicates the type of event that caused the entry to be made: recvNegBindRsp - Received a negative bind response from the partner LU. sendNegBindRsp - Sent a negative bind response to the partner LU. sessActRejected - Session activation rejected by the partner LU. unbindSent - Unbind sent to the partner LU. unbindReceived - Unbind received from the partner LU. These event types correspond to the five SNA/MS Alerts LU62001 through LU62005, documented in the SNA Management Services Reference. |
| OCT appcHistSessUnbindType | 1.3.6.1.2.1.34.3.1.4.3.1.7 | OCTET STRING | read-only | The type of unbind which terminated the session. This value is consists of one (1) octet; and its meaning is defined in SNA Formats. |
| STR appcLluAdminAlias | 1.3.6.1.2.1.34.3.1.2.1.1.10 | DisplayString | read-only | A local alias for the local LU. If not known or not applicable, this object contains a zero-length string. |
| INT appcLluAdminBindRspMayQ | 1.3.6.1.2.1.34.3.1.2.1.1.5 | INTEGER | read-only | Indicates whether or not the local LU, as the sender of a BIND request, allows a partner partner LU to delay sending the BIND response if the partner LU cannot process the BIND request immediately. |
| INT appcLluAdminCompression | 1.3.6.1.2.1.34.3.1.2.1.1.6 | INTEGER | read-only | Specifies whether compression is supported. The local LU uses this value for negotiation during session activation (SNA BIND). prohibited - specifies that no compression is to be used. required - specifies that compression is required. negotiable - specifies that the usage of compression is to be negotiated between the LUs. The level of compression is also negotiated. |
| INT appcLluAdminCompRleBeforeLZ | 1.3.6.1.2.1.34.3.1.2.1.1.9 | INTEGER | read-only | Specifies whether run-length encoding is to be applied to the data before applying Lempel-Ziv-like compression. The local LU uses this value for negotiation during session activation (SNA BIND). This parameter is only supported if LZ compression is used. |
| INT appcLluAdminDepType | 1.3.6.1.2.1.34.3.1.2.1.1.2 | INTEGER | read-only | This value identifies whether the LU is dependent or independent. |
| appcLluAdminEntry | 1.3.6.1.2.1.34.3.1.2.1.1 | not-accessible | Information about local APPC LUs. | |
| INT appcLluAdminInBoundCompLevel | 1.3.6.1.2.1.34.3.1.2.1.1.7 | INTEGER | read-only | Specifies the maximum level of compression supported for inbound data. The local LU uses this value in conjunction with appcLluAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression. |
| OCT appcLluAdminLocalAddress | 1.3.6.1.2.1.34.3.1.2.1.1.3 | OCTET STRING | read-only | The local address for this LU is a byte with a value ranging from 0 to 254. For dependent LUs, this value ranges from 1 to 254; for independent LUs this value is always 0. |
| STR appcLluAdminName | 1.3.6.1.2.1.34.3.1.2.1.1.1 | DisplayString | not-accessible | Specifies the name of the local LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. |
| INT appcLluAdminOutBoundCompLevel | 1.3.6.1.2.1.34.3.1.2.1.1.8 | INTEGER | read-only | Specifies the maximum level of compression supported for outbound data. The local LU uses this value in conjunction with appcLluAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression. |
| I32 appcLluAdminSessLimit | 1.3.6.1.2.1.34.3.1.2.1.1.4 | Integer32 | read-only | The maximum number of sessions supported by this LU. |
| appcLluAdminTable | 1.3.6.1.2.1.34.3.1.2.1 | not-accessible | APPC Local LU Admin Table. | |
| appcLluConfGroup | 1.3.6.1.2.1.34.3.2.2.2 | A collection of objects providing the instrumentation of APPC local LU6.2s. | ||
| G32 appcLluOperActiveSessions | 1.3.6.1.2.1.34.3.1.2.2.1.11 | Gauge32 | read-only | Specifies the total number of active APPC sessions for this LU. |
| STR appcLluOperAlias | 1.3.6.1.2.1.34.3.1.2.2.1.10 | DisplayString | read-only | A local alias for the local LU. If not known or not applicable, this object contains a zero-length string. |
| INT appcLluOperBindRspMayQ | 1.3.6.1.2.1.34.3.1.2.2.1.5 | INTEGER | read-only | Indicates whether or not the local LU, as the sender of a BIND request, allows a partner LU to delay sending the BIND response if the partner LU cannot process the BIND request immediately. |
| INT appcLluOperCompression | 1.3.6.1.2.1.34.3.1.2.2.1.6 | INTEGER | read-only | Specifies whether compression is supported. The local LU uses this value for negotiation during session activation (SNA BIND). prohibited - specifies that no compression is to be used. required - specifies that compression is required. negotiable - specifies that the usage of compression is to be negotiated between the LUs. The level of compression is also negotiated. |
| INT appcLluOperCompRleBeforeLZ | 1.3.6.1.2.1.34.3.1.2.2.1.9 | INTEGER | read-only | Specifies whether run-length encoding is to be applied to the data before applying Lempel-Ziv-like compression. The local LU uses this value for negotiation during session activation (SNA BIND). This parameter is only supported if LZ compression is used. |
| INT appcLluOperDepType | 1.3.6.1.2.1.34.3.1.2.2.1.2 | INTEGER | read-only | This value identifies whether the LU is dependent or independent. |
| appcLluOperEntry | 1.3.6.1.2.1.34.3.1.2.2.1 | not-accessible | Information about local APPC LUs. | |
| INT appcLluOperInBoundCompLevel | 1.3.6.1.2.1.34.3.1.2.2.1.7 | INTEGER | read-only | Specifies the maximum level of compression supported for inbound data. The local LU uses this value in conjunction with appcLluOperCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression. |
| OCT appcLluOperLocalAddress | 1.3.6.1.2.1.34.3.1.2.2.1.3 | OCTET STRING | read-only | The local address for this LU is a byte with a value ranging from 0 to 254. For dependent LUs, this value ranges from 1 to 254; for independent LUs this value is always 0. |
| STR appcLluOperName | 1.3.6.1.2.1.34.3.1.2.2.1.1 | DisplayString | not-accessible | Specifies the name of the local LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. |
| INT appcLluOperOutBoundCompLevel | 1.3.6.1.2.1.34.3.1.2.2.1.8 | INTEGER | read-only | Specifies the maximum level of compression supported for outbound data. The local LU uses this value in conjunction with appcLluAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression. |
| I32 appcLluOperSessLimit | 1.3.6.1.2.1.34.3.1.2.2.1.4 | Integer32 | read-only | The maximum number of sessions supported by this LU. |
| appcLluOperTable | 1.3.6.1.2.1.34.3.1.2.2 | not-accessible | APPC Local LU Operational Table. | |
| STR appcLocalCpName | 1.3.6.1.2.1.34.3.1.1.3.9 | DisplayString | read-only | Specifies the name of the local control point. This field is from 0 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. A null string indicates that the value is unknown. |
| appcLu | 1.3.6.1.2.1.34.3.1.2 | |||
| appcLuPairAdminEntry | 1.3.6.1.2.1.34.3.1.2.3.1 | not-accessible | Entry of APPC Partner LU Information Table. It is indexed by the local and partner LU Names. | |
| NUM appcLuPairAdminLinkObjId | 1.3.6.1.2.1.34.3.1.2.3.1.7 | InstancePointer | read-only | Specifies the link associated with this partner LU. This value points to the row in the table containing information on the link instance. (e.g., the sdlcLSAdminTable of the SNA DLC MIB module). This object may be NULL if the link is not specified or if a link is not applicable (as for APPN-level nodes). |
| STR appcLuPairAdminLocLuName | 1.3.6.1.2.1.34.3.1.2.3.1.1 | DisplayString | not-accessible | The SNA name of the local LU to which this partner LU definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. The reserved value '*ALL' indicates that the partner LU definition applies to all local LUs, and not just to a single local LU. |
| INT appcLuPairAdminParaSessSup | 1.3.6.1.2.1.34.3.1.2.3.1.8 | INTEGER | read-only | Defined Parallel Sessions Supported. Indicates whether or not multiple sessions between the partner LU and its associated local LU are permitted. Parallel session support also indicates that Change Number of Sessions (CNOS) will be used to negotiate session limits between the LUs. |
| STR appcLuPairAdminParLuAlias | 1.3.6.1.2.1.34.3.1.2.3.1.3 | DisplayString | read-only | A local alias for the partner LU. If not known or not applicable, this object contains a zero-length string. |
| STR appcLuPairAdminParLuName | 1.3.6.1.2.1.34.3.1.2.3.1.2 | DisplayString | not-accessible | The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. |
| INT appcLuPairAdminSecAccept | 1.3.6.1.2.1.34.3.1.2.3.1.6 | INTEGER | read-only | Specifies support for different levels of access security information in ATTACH requests received from this partner LU. Possible values are: none - No access security information will be accepted on allocation requests (ATTACH) from this LU. conversation - Allocation requests will not be accepted that include already verified or persistent verification indicators. Accept conversation-level access security information, which must include both a user Id and password, and may also include a profile. alreadyVerified - Allocation requests will be accepted that include already verified indicators. Persistent verification indicators will not be accepted. persistentVerification - Allocation requests will be accepted that include persistent verification indicators. Already verified indicators will not be accepted. aVandpV - Allocation requests will be accepted that include already verified or persistent verification indicators. |
| I32 appcLuPairAdminSessLimit | 1.3.6.1.2.1.34.3.1.2.3.1.4 | Integer32 | read-only | The maximum number of sessions supported by this partner LU. |
| INT appcLuPairAdminSessSec | 1.3.6.1.2.1.34.3.1.2.3.1.5 | INTEGER | read-only | Specifies the type of session-level security information that a local LU will accept on BIND requests it receives from the partner LU. required - Specifies that the BIND request must carry session level verification information that will be verified upon receipt. accepted - Specifies that the BIND request may carry session level verification information that will be verified upon receipt. notAllowed - Specifies that the BIND request must not carry session level verification information. |
| appcLuPairAdminTable | 1.3.6.1.2.1.34.3.1.2.3 | not-accessible | APPC Partner LU administrative Table | |
| appcLuPairOperEntry | 1.3.6.1.2.1.34.3.1.2.4.1 | not-accessible | Entry representing one partner/local LU pair. | |
| NUM appcLuPairOperLinkObjId | 1.3.6.1.2.1.34.3.1.2.4.1.7 | InstancePointer | read-only | Specifies the link associated with this partner LU. This value points to the row in the table containing information on the link instance. (e.g., the sdlcLSAdminTable of the SNA DLC MIB module). This object may be NULL if the link is not specified or if a link is not applicable (as for APPN-level nodes). |
| STR appcLuPairOperLocLuName | 1.3.6.1.2.1.34.3.1.2.4.1.1 | DisplayString | not-accessible | The SNA name of the local LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. If this object has the same value as appcLluOperName, then the two entries being indexed apply to the same resource (specifically, to the same local LU). |
| INT appcLuPairOperParaSessSup | 1.3.6.1.2.1.34.3.1.2.4.1.8 | INTEGER | read-only | Active Parallel Sessions Supported. Indicates whether or not multiple session between the partner LU and its associated local LU are permitted. Parallel session support also indicates that Change Number of Sessions (CNOS) will be used to negotiate session limits between the LUs. |
| INT appcLuPairOperParaSessSupLS | 1.3.6.1.2.1.34.3.1.2.4.1.9 | INTEGER | read-only | Active Parallel Sessions Supported - last starting value. This object represents the initial value proposed by the local LU the last time this capability was negotiated, i.e., when the first session was bound between the local LU and its partner. |
| STR appcLuPairOperParLuAlias | 1.3.6.1.2.1.34.3.1.2.4.1.3 | DisplayString | read-only | A local alias for the partner LU. If not known or not applicable, this object contains a zero-length string. |
| STR appcLuPairOperParLuName | 1.3.6.1.2.1.34.3.1.2.4.1.2 | DisplayString | not-accessible | The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. |
| INT appcLuPairOperSecAccept | 1.3.6.1.2.1.34.3.1.2.4.1.6 | INTEGER | read-only | Specifies support for different levels of security acceptance information in ATTACH requests received from this partner LU. Possible values are: none - No access security information will be accepted on allocation requests (ATTACH) from this LU. conversation - Allocation requests will not be accepted that include already verified or persistent verification indicators. Accept conversation-level access security information, which must include both a user Id and password, and may also include a profile. alreadyVerified - Allocation requests will be accepted that include already verified indicators. Persistent verification indicators will not be accepted. persistentVerification - Allocation requests will be accepted that include persistent verification indicators. Already verified indicators will not be accepted. aVandpV - Allocation requests will be accepted that include already verified or persistent verification indicators. |
| I32 appcLuPairOperSessLimit | 1.3.6.1.2.1.34.3.1.2.4.1.4 | Integer32 | read-only | The maximum number of sessions supported by this partner LU. |
| INT appcLuPairOperSessSec | 1.3.6.1.2.1.34.3.1.2.4.1.5 | INTEGER | read-only | Specifies the type of security information that a local LU will accept on BIND requests it receives from the partner LU. required - Specifies that the BIND request must carry session level verification information that will be verified upon receipt. accepted - Specifies that the BIND request may carry session level verification information that will be verified upon receipt. notAllowed - Specifies that the BIND request must not carry session level verification information. |
| INT appcLuPairOperState | 1.3.6.1.2.1.34.3.1.2.4.1.10 | INTEGER | read-only | The value identifies the current operational state of this LU pair: inactive (1) - no active or pending session exists between the LUs. active (2) - an active or pending session exists between the LUs. |
| appcLuPairOperTable | 1.3.6.1.2.1.34.3.1.2.4 | not-accessible | Table of active partner/local LU pairs. Two entries are present in the table when both LUs in a pair are local. | |
| appcMIB | 1.3.6.1.2.1.34.3 | This is the MIB module for objects used to manage network devices with APPC capabilities. | ||
| INT appcModeAdminCompression | 1.3.6.1.2.1.34.3.1.2.5.1.19 | INTEGER | read-only | Specifies whether compression is supported. The local LU uses this value for negotiation during session activation (SNA BIND). prohibited - specifies that no compression is to be used. required - specifies that compression is required. negotiable - specifies that the usage of compression is to be negotiated between the LUs. The level of compression is also negotiated. |
| INT appcModeAdminCompRleBeforeLZ | 1.3.6.1.2.1.34.3.1.2.5.1.22 | INTEGER | read-only | Specifies whether run-length encoding is to be applied to the data before applying Lempel-Ziv-like compression. The local LU uses this value for negotiation during session activation (SNA BIND). This parameter is only supported if LZ compression is used. |
| I32 appcModeAdminConWinAutoActLmt | 1.3.6.1.2.1.34.3.1.2.5.1.9 | Integer32 | read-only | Specifies the limit on the number of contention winner sessions to be automatically activated when the minimum number of contention winner sessions increases (as a result of CNOS processing). The actual number of sessions activated is the lesser of this value and the new minimum number of contention winner sessions. |
| STR appcModeAdminCosName | 1.3.6.1.2.1.34.3.1.2.5.1.4 | DisplayString | read-only | Specifies the class of service (COS) name associated with this mode. If the implementation does not support COS names, a null string is returned. |
| INT appcModeAdminCrypto | 1.3.6.1.2.1.34.3.1.2.5.1.24 | INTEGER | read-only | Specifies whether session-level cryptography is supported. This value is used for negotiation during session activations (SNA BIND). notSupported - Specifies session-level cryptography is not to be used. mandatory - Specifies session-level cryptography must be used. selective - Specifies session-level cryptography is required just on selected requests flowing on the sessions. |
| appcModeAdminEntry | 1.3.6.1.2.1.34.3.1.2.5.1 | not-accessible | Entry of APPC Mode Information Table. | |
| INT appcModeAdminInBoundCompLevel | 1.3.6.1.2.1.34.3.1.2.5.1.20 | INTEGER | read-only | Specifies the maximum level of compression supported for inbound data. The local LU uses this value in conjunction with appcModeAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression. |
| STR appcModeAdminLocLuName | 1.3.6.1.2.1.34.3.1.2.5.1.1 | DisplayString | not-accessible | The SNA name of the local LU to which this mode definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. The reserved value '*ALL' indicates that the mode definition applies to all local LUs for the SNA node identified by appcLocalCpName, and not just to a single local LU. |
| I32 appcModeAdminMaxSessLimit | 1.3.6.1.2.1.34.3.1.2.5.1.6 | Integer32 | read-only | Specifies the maximum value that the local LU is to use, during CNOS processing, for the session limit. The local LU, as a target LU, will negotiate a higher session limit it receives in the CNOS request down to this maximum value. The local LU, as a source LU, will restrict the session limit it sends in a CNOS request to a value less than or equal to this maximum value. |
| I32 appcModeAdminMinClosLimit | 1.3.6.1.2.1.34.3.1.2.5.1.8 | Integer32 | read-only | Specifies the default minimum contention loser sessions limit. Some implementations internally issue a INITIALIZE_SESSION_LIMIT verb when a Mode is created. This value is the parameter used for the CNOS processing of that verb. This is the same as target minimum contention winner sessions. This parameter is not used when issuing an explicit INITIALIZE_SESSION_LIMIT verb. The equivalent object in appcCnosCommandTable is used. |
| I32 appcModeAdminMinCwinLimit | 1.3.6.1.2.1.34.3.1.2.5.1.7 | Integer32 | read-only | Specifies the default minimum contention winner sessions limit. Some implementations internally issue a INITIALIZE_SESSION_LIMIT verb when a Mode is created. This value is the parameter used for the CNOS processing of that verb. This parameter is not used when issuing an explicit INITIALIZE_SESSION_LIMIT verb. The equivalent object in appcCnosCommandTable is used. |
| STR appcModeAdminModeName | 1.3.6.1.2.1.34.3.1.2.5.1.3 | DisplayString | not-accessible | Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters). |
| INT appcModeAdminOutBoundCompLevel | 1.3.6.1.2.1.34.3.1.2.5.1.21 | INTEGER | read-only | Specifies the maximum level of compression supported for outbound data. The local LU uses this value in conjunction with appcModeAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression. |
| STR appcModeAdminParLuName | 1.3.6.1.2.1.34.3.1.2.5.1.2 | DisplayString | not-accessible | The SNA name of the partner LU to which this mode definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. The reserved value '*ALL' indicates that the mode definition applies to all partner LUs for the SNA node identified by appcModeAdminLocLuName, and not just to a single partner LU. |
| I32 appcModeAdminPrefRecvRuSz | 1.3.6.1.2.1.34.3.1.2.5.1.12 | Integer32 | read-only | Specifies the preferred receive RU (Request Unit) size of normal-flow requests on the sessions. This value must be less than or equal to the value specified in appcModeAdminRecvRuSzUpBnd and greater than or equal to the value specified in appcModeAdminRecvRuSzLoBnd. The local LU specifies this value for the receive maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeAdminRecvRuSzUpBnd value or down to the appcModeAdminRecvRuSzLoBnd value. |
| I32 appcModeAdminPrefSendRuSz | 1.3.6.1.2.1.34.3.1.2.5.1.13 | Integer32 | read-only | Specifies the preferred send RU (Request Unit) size of normal- flow requests on the sessions. This value must be less than or equal to the value specified in appcModeAdminSendRuSzUpBnd and greater than or equal to the value specified in appcModeAdminSendRuSzLoBnd. The local LU specifies this value for the send maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeAdminSendRuSzUpBnd value or down to the appcModeAdminSendRuSzLoBnd value. |
| I32 appcModeAdminRecvPacWinSz | 1.3.6.1.2.1.34.3.1.2.5.1.10 | Integer32 | read-only | Specifies the size of the receive pacing window. This value is used for negotiation during session activations (SNA BIND). The meaning of this value when set to 0 depends on whether adaptive pacing is supported: adaptive pacing No limit on window size fixed pacing No pacing is supported |
| I32 appcModeAdminRecvRuSzLoBnd | 1.3.6.1.2.1.34.3.1.2.5.1.16 | Integer32 | read-only | Specifies the lower bound for the maximum receive RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). |
| I32 appcModeAdminRecvRuSzUpBnd | 1.3.6.1.2.1.34.3.1.2.5.1.14 | Integer32 | read-only | Specifies the upper bound for the maximum receive RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). |
| I32 appcModeAdminSendPacWinSz | 1.3.6.1.2.1.34.3.1.2.5.1.11 | Integer32 | read-only | Specifies the size of the send pacing window. This value is used for negotiation during session activations (SNA BIND). The meaning of this value when set to 0 depends on whether adaptive pacing is supported: adaptive pacing No limit on window size fixed pacing No pacing is supported |
| I32 appcModeAdminSendRuSzLoBnd | 1.3.6.1.2.1.34.3.1.2.5.1.17 | Integer32 | read-only | Specifies the lower bound for the maximum send RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). |
| I32 appcModeAdminSendRuSzUpBnd | 1.3.6.1.2.1.34.3.1.2.5.1.15 | Integer32 | read-only | Specifies the upper bound for the maximum send RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). |
| STR appcModeAdminSessEndTpName | 1.3.6.1.2.1.34.3.1.2.5.1.5 | DisplayString | read-only | Specifies the name of the transaction program (TP) to be invoked when a session using this mode is deactivated or ended. If no such TP is defined, this object is a null string. When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non- displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes). |
| INT appcModeAdminSingSessReinit | 1.3.6.1.2.1.34.3.1.2.5.1.18 | INTEGER | read-only | Specifies the responsibility for session reinitiation of a single session with the partner LU (when the session goes down). The local LU uses this parameter to specify the session reinitiation responsibility in session activation (SNA BIND) requests and responses. notApplicable - specifies that this parameter has no meaning since the value of appcLuPairAdminParaSessSup is yes. The field in the SNA BIND is reserved (set to zero). operatorControlled - specifies that neither LU will automatically attempt to reinitiate the session. The operator on either side will manually reactivate the session. A contention race (both side reinitiating at the same time) is won by the LU with the lexicographically greater fully- qualified LU name. primaryOnly - specifies that the primary LU will automatically attempt to reinitiate the session. secondaryOnly - specifies that the secondary LU will automatically attempt to reinitiate the session. primaryOrSecondary - specifies that either the primary or the secondary may automatically attempt to reinitiate the session. A contention race is handled the same way as with operatorControlled. |
| INT appcModeAdminSyncLvl | 1.3.6.1.2.1.34.3.1.2.5.1.23 | INTEGER | read-only | Specifies the sync level support. This value is used for negotiation during session activations (SNA BIND). none - No sync level is supported. noneConfirm - None and Confirm levels supported. noneConfirmSyncPoint - None, Confirm, and Sync Point is supported. |
| appcModeAdminTable | 1.3.6.1.2.1.34.3.1.2.5 | not-accessible | APPC Mode Table | |
| appcModeConfGroup | 1.3.6.1.2.1.34.3.2.2.4 | A collection of objects providing the instrumentation of APPC modes. | ||
| G32 appcModeOperActClos | 1.3.6.1.2.1.34.3.1.2.6.1.30 | Gauge32 | read-only | Specifies the number of active contention loser sessions. |
| G32 appcModeOperActCwin | 1.3.6.1.2.1.34.3.1.2.6.1.29 | Gauge32 | read-only | Specifies the number of active contention winner sessions. |
| INT appcModeOperCNOSNeg | 1.3.6.1.2.1.34.3.1.2.6.1.28 | INTEGER | read-only | Specifies whether CNOS negotiation is in process. CNOS negotiation is used to set or change the various session limits for a mode. |
| INT appcModeOperCompression | 1.3.6.1.2.1.34.3.1.2.6.1.20 | INTEGER | read-only | Specifies whether compression is supported. The local LU uses this value for negotiation during session activation (SNA BIND). prohibited - specifies that no compression is to be used. required - specifies that compression is required. negotiable - specifies that the usage of compression is to be negotiated between the LUs. The level of compression is also negotiated. |
| INT appcModeOperCompRleBeforeLZ | 1.3.6.1.2.1.34.3.1.2.6.1.23 | INTEGER | read-only | Specifies whether run-length encoding is to be applied to the data before applying Lempel-Ziv-like compression. The local LU uses this value for negotiation during session activation (SNA BIND). This parameter is only supported if LZ compression is used. |
| I32 appcModeOperConWinAutoActLmt | 1.3.6.1.2.1.34.3.1.2.6.1.10 | Integer32 | read-only | Specifies the limit on the number of contention winner sessions to be automatically activated when the minimum number of contention winner sessions increases (as a result of CNOS processing). The actual number of sessions activated is the lesser of this value and the new minimum number of contention winner sessions. |
| STR appcModeOperCosName | 1.3.6.1.2.1.34.3.1.2.6.1.4 | DisplayString | read-only | Specifies the class of service (COS) name associated with this mode. If the implementation does not support COS names, a zero-length string is returned. |
| INT appcModeOperCrypto | 1.3.6.1.2.1.34.3.1.2.6.1.25 | INTEGER | read-only | Specifies whether session-level cryptography is supported for sessions involving this LU pair and mode name. notSupported - Specifies session-level cryptography is not being used. mandatory - Specifies session-level cryptography in being used on all requests flowing on the sessions. selective - Specifies session-level cryptography is required just on selected requests flowing on the sessions. |
| INT appcModeOperCryptoLastStart | 1.3.6.1.2.1.34.3.1.2.6.1.27 | INTEGER | read-only | Specifies whether session-level cryptography is supported. This value represents the initial value proposed by the local LU the last time this capability was negotiated, i.e., when the first session was bound between the local LU and its partner. notSupported - Specifies session-level cryptography is not to be used. mandatory - Specifies session-level cryptography must be used. selective - Specifies session-level cryptography is required just on selected requests flowing on the sessions. |
| INT appcModeOperDrainPart | 1.3.6.1.2.1.34.3.1.2.6.1.36 | INTEGER | read-only | Specifies whether the partner LU is draining its conversations for this mode. When a mode session limit is reset (via a CNOS RESET_SESSION_LIMIT request), the partner LU could be set to process all queued conversations before deactivating all of the sessions (using the SNA Bracket Initiation Stop or BIS protocol). |
| INT appcModeOperDrainSelf | 1.3.6.1.2.1.34.3.1.2.6.1.35 | INTEGER | read-only | Specifies whether the local LU is draining its conversations for this mode. When a mode session limit is reset (via a CNOS RESET_SESSION_LIMIT request), the local LU could be set to process all queued conversations before deactivating all of the sessions (using the SNA Bracket Initiation Stopped or BIS protocol). |
| appcModeOperEntry | 1.3.6.1.2.1.34.3.1.2.6.1 | not-accessible | Entry of APPC mode operational information table. This entry does not augment the appcModeAdminEntry, but reflects an actual operational mode for a given local LU - partner LU pair. | |
| INT appcModeOperInBoundCompLevel | 1.3.6.1.2.1.34.3.1.2.6.1.21 | INTEGER | read-only | Specifies the maximum level of compression supported for inbound data. The local LU uses this value in conjunction with appcModeOperCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression. |
| STR appcModeOperLocLuName | 1.3.6.1.2.1.34.3.1.2.6.1.1 | DisplayString | not-accessible | The SNA name of the local LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. If this object has the same value as appcLluOperName, then the two entries being indexed apply to the same resource (specifically, to the same local LU). |
| I32 appcModeOperMaxSessLimit | 1.3.6.1.2.1.34.3.1.2.6.1.7 | Integer32 | read-only | Specifies the maximum value that the local LU is to use, during CNOS processing, for the session limit. The local LU, as a target LU, will negotiate a higher session limit it receives in the CNOS request down to this maximum value. The local LU, as a source LU, will restrict the session limit it sends in a CNOS request to a value less than or equal to this maximum value. |
| I32 appcModeOperMinClosLimit | 1.3.6.1.2.1.34.3.1.2.6.1.9 | Integer32 | read-only | Specifies the minimum contention loser sessions limit that was negotiated via CNOS processing. This is the same as target minimum contention winner sessions. |
| I32 appcModeOperMinCwinLimit | 1.3.6.1.2.1.34.3.1.2.6.1.8 | Integer32 | read-only | Specifies the minimum contention winner sessions limit that was negotiated via CNOS processing. |
| STR appcModeOperModeName | 1.3.6.1.2.1.34.3.1.2.6.1.3 | DisplayString | not-accessible | Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters). |
| INT appcModeOperOutBoundCompLevel | 1.3.6.1.2.1.34.3.1.2.6.1.22 | INTEGER | read-only | Specifies the maximum level of compression supported for outbound data. The local LU uses this value in conjunction with appcModeOperCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression. |
| STR appcModeOperParLuName | 1.3.6.1.2.1.34.3.1.2.6.1.2 | DisplayString | not-accessible | The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. If this object has the same value as appcLuPairOperParLuName, then the two entries being indexed apply to the same resource (specifically, to the same partner LU). |
| G32 appcModeOperPndClos | 1.3.6.1.2.1.34.3.1.2.6.1.32 | Gauge32 | read-only | Specifies the number of contention loser sessions that are pending activation. |
| G32 appcModeOperPndCwin | 1.3.6.1.2.1.34.3.1.2.6.1.31 | Gauge32 | read-only | Specifies the number of contention winner sessions that are pending activation. |
| I32 appcModeOperPrefRecvRuSz | 1.3.6.1.2.1.34.3.1.2.6.1.13 | Integer32 | read-only | Specifies the preferred receive RU (Request Unit) size of normal-flow requests on the sessions. This value must be less than or equal to the value specified in appcModeOperRecvRuSzUpBnd and greater than or equal to the value specified in appcModeOperRecvRuSzLoBnd. The local LU specifies this value for the receive maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeOperRecvRuSzUpBnd value or down to the appcModeOperRecvRuSzLoBnd value. |
| I32 appcModeOperPrefSendRuSz | 1.3.6.1.2.1.34.3.1.2.6.1.14 | Integer32 | read-only | Specifies the preferred send RU (Request Unit) size of normal- flow requests on the sessions. This value must be less than or equal to the value specified in appcModeOperSendRuSzUpBnd and greater than or equal to the value specified in appcModeOperSendRuSzLoBnd. The local LU specifies this value for the send maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeOperSendRuSzUpBnd value or down to the appcModeOperSendRuSzLoBnd value. |
| G32 appcModeOperPtmClos | 1.3.6.1.2.1.34.3.1.2.6.1.34 | Gauge32 | read-only | Specifies the number of contention loser sessions that are pending termination. |
| G32 appcModeOperPtmCwin | 1.3.6.1.2.1.34.3.1.2.6.1.33 | Gauge32 | read-only | Specifies the number of contention winner sessions that are pending termination. |
| I32 appcModeOperRecvPacWinSz | 1.3.6.1.2.1.34.3.1.2.6.1.11 | Integer32 | read-only | Specifies the size of the receive pacing window. This value is used for negotiation during session activations (SNA BIND). The meaning of this value when set to 0 depends on whether adaptive pacing is supported: adaptive pacing - No limit on window size fixed pacing - No pacing is supported |
| I32 appcModeOperRecvRuSzLoBnd | 1.3.6.1.2.1.34.3.1.2.6.1.17 | Integer32 | read-only | Specifies the lower bound for the maximum receive RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). |
| I32 appcModeOperRecvRuSzUpBnd | 1.3.6.1.2.1.34.3.1.2.6.1.15 | Integer32 | read-only | Specifies the upper bound for the maximum receive RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). |
| I32 appcModeOperSendPacWinSz | 1.3.6.1.2.1.34.3.1.2.6.1.12 | Integer32 | read-only | Specifies the size of the send pacing window. This value is used for negotiation during session activations (SNA BIND). The meaning of this value when set to 0 depends on whether adaptive pacing is supported: adaptive pacing No limit on window size fixed pacing No pacing is supported |
| I32 appcModeOperSendRuSzLoBnd | 1.3.6.1.2.1.34.3.1.2.6.1.18 | Integer32 | read-only | Specifies the lower bound for the maximum send RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). |
| I32 appcModeOperSendRuSzUpBnd | 1.3.6.1.2.1.34.3.1.2.6.1.16 | Integer32 | read-only | Specifies the upper bound for the maximum send RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). |
| STR appcModeOperSessEndTpName | 1.3.6.1.2.1.34.3.1.2.6.1.5 | DisplayString | read-only | Specifies the name of the transaction program (TP) to be invoked when a session using this mode is deactivated or ended. If the name is NULL, no transaction program is invoked. When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non- displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes). |
| I32 appcModeOperSessLimit | 1.3.6.1.2.1.34.3.1.2.6.1.6 | Integer32 | read-only | Specifies the current session limit of this mode as negotiated through APPC CNOS (Change Number of Sessions) processing. Identifies the total number of sessions that can be established between the local and partner LU using this mode. |
| INT appcModeOperSingSessReinit | 1.3.6.1.2.1.34.3.1.2.6.1.19 | INTEGER | read-only | Specifies the responsibility for session reinitiation of a single session with the partner LU (when the session goes down). The local LU uses this parameter to specify the session reinitiation responsibility in session activation (SNA BIND) requests and responses. notApplicable - specifies that this parameter has no meaning since the value of appcLuPairOperParaSessSup is yes. The field in the SNA BIND is reserved (set to zero). operatorControlled - specifies that neither LU will automatically attempt to reinitiate the session. The operator on either side will manually reactivate the session. A contention race (both side reinitiating at the same time) is won by the LU with the lexicographically greater fully- qualified LU name. primaryOnly - specifies that the primary LU will automatically attempt to reinitiate the session. secondaryOnly - specifies that the secondary LU will automatically attempt to reinitiate the session. primaryOrSecondary - specifies that either the primary or the secondary may automatically attempt to reinitiate the session. A contention race is handled the same way as with operatorControlled. |
| INT appcModeOperSyncLvl | 1.3.6.1.2.1.34.3.1.2.6.1.24 | INTEGER | read-only | Specifies the sync level support for sessions involving this LU pair and mode name. none - No sync level is supported. noneConfirm - None and Confirm level supported. noneConfirmSyncPoint - None, Confirm and Sync Point is supported. |
| INT appcModeOperSyncLvlLastStart | 1.3.6.1.2.1.34.3.1.2.6.1.26 | INTEGER | read-only | Specifies the sync level support. This value represents the initial value proposed by the local LU the last time this capability was negotiated, i.e., when the first session was bound between the local LU and its partner. none - No sync level is supported. noneConfirm - None and Confirm level supported. noneConfirmSyncPoint - None, Confirm and Sync Point is supported. |
| appcModeOperTable | 1.3.6.1.2.1.34.3.1.2.6 | not-accessible | Operational APPC Mode Information. Two entries are present in the table when both LUs in a pair are local. | |
| appcObjects | 1.3.6.1.2.1.34.3.1 | |||
| appcParLuConfGroup | 1.3.6.1.2.1.34.3.2.2.3 | A collection of objects providing the instrumentation of APPC partner LUs. | ||
| appcSession | 1.3.6.1.2.1.34.3.1.4 | |||
| appcSessionConfGroup | 1.3.6.1.2.1.34.3.2.2.6 | A collection of objects providing the instrumentation of APPC LU6.2 sessions. | ||
| appcSessRtpEntry | 1.3.6.1.2.1.34.3.1.4.4.1 | not-accessible | Entry of APPC session RTP table. | |
| OCT appcSessRtpNceId | 1.3.6.1.2.1.34.3.1.4.4.1.1 | OCTET STRING | not-accessible | The local Network Connection Endpoint of the RTP connection. |
| G32 appcSessRtpSessions | 1.3.6.1.2.1.34.3.1.4.4.1.3 | Gauge32 | read-only | The number of APPC sessions terminating in this node that are using this RTP connection. |
| appcSessRtpTable | 1.3.6.1.2.1.34.3.1.4.4 | not-accessible | A table indicating how many APPC sessions terminating in this node are transported by each RTP connection. | |
| OCT appcSessRtpTcid | 1.3.6.1.2.1.34.3.1.4.4.1.2 | OCTET STRING | not-accessible | The local TCID of the RTP connection. |
| TIK appcSessStatsCtrUpTime | 1.3.6.1.2.1.34.3.1.4.2.1.12 | TimeTicks | read-only | The length of time the counters for this session have been active, measured in hundredths of a second. |
| appcSessStatsEntry | 1.3.6.1.2.1.34.3.1.4.2.1 | not-accessible | Contains statistics information for an APPC session. Each entry is created by the Agent. Objects in this table have read-only access. Each session from appcActSessTable has one entry in this table. | |
| STR appcSessStatsLocLuName | 1.3.6.1.2.1.34.3.1.4.2.1.1 | DisplayString | not-accessible | Specifies the name of the local LU for the session. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. If this object has the same value as appcLluOperName, then the two entries being indexed apply to the same resource (specifically, to the same local LU). |
| STR appcSessStatsParLuName | 1.3.6.1.2.1.34.3.1.4.2.1.2 | DisplayString | not-accessible | Specifies the name of the partner LU for the session. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. If this object has the same value as appcLuPairOperParLuName, then the two entries being indexed apply to the same resource (specifically, to the same partner LU). |
| C32 appcSessStatsRcvdFmdBytes | 1.3.6.1.2.1.34.3.1.4.2.1.6 | Counter32 | read-only | The number of function management data (FMD) bytes received by the local LU. |
| C32 appcSessStatsRcvdFmdRus | 1.3.6.1.2.1.34.3.1.4.2.1.10 | Counter32 | read-only | The number of function management data (FMD) RUs received by the local LU. |
| C32 appcSessStatsRcvdNonFmdBytes | 1.3.6.1.2.1.34.3.1.4.2.1.7 | Counter32 | read-only | The number of non-function management data (non-FMD) bytes received by the local LU. |
| C32 appcSessStatsRcvdNonFmdRus | 1.3.6.1.2.1.34.3.1.4.2.1.11 | Counter32 | read-only | The number of non-function management data (non-FMD) RUs received by the local LU. |
| C32 appcSessStatsSentFmdBytesEx | 1.3.6.1.2.1.34.3.1.4.2.1.4 | Counter32 | read-only | The number of function management data (FMD) bytes sent by the local LU. |
| C32 appcSessStatsSentFmdRus | 1.3.6.1.2.1.34.3.1.4.2.1.8 | Counter32 | read-only | The number of function management data (FMD) RUs sent by the local LU. |
| C32 appcSessStatsSentNonFmdBytes | 1.3.6.1.2.1.34.3.1.4.2.1.5 | Counter32 | read-only | The number of non-function management data (non-FMD) bytes sent by the local LU. |
| C32 appcSessStatsSentNonFmdRus | 1.3.6.1.2.1.34.3.1.4.2.1.9 | Counter32 | read-only | The number of non-function management data (non-FMD) RUs sent by the local LU. |
| I32 appcSessStatsSessIndex | 1.3.6.1.2.1.34.3.1.4.2.1.3 | Integer32 | not-accessible | This value identifies the index of the session, which is unique for this LU pair. It is recommended that an Agent not reuse the index of a deactivated session for a significant period of time (e.g., one week). If this object has the same value as appcActSessIndex for the same LU pair, then the two entries being indexed apply to the same resource (specifically, to the same session). |
| appcSessStatsTable | 1.3.6.1.2.1.34.3.1.4.2 | not-accessible | This table contains dynamic statistical information relating to active APPC sessions. The entries in this table cannot be created by a Management Station. Two entries are present in the table when both session partners are local. This table is populated only when the value of appcCntrlOperStat is 'active'. | |
| appcTp | 1.3.6.1.2.1.34.3.1.3 | |||
| INT appcTpAdminConvDuplex | 1.3.6.1.2.1.34.3.1.3.1.1.13 | INTEGER | read-only | Specifies the conversation duplex type (half or full) that will be used by the TP. This value is verified upon receipt of an incoming attach. The acceptable values are: half - Indicates that this transaction program supports half duplex conversations. full - Indicates that this transaction program supports full duplex conversations. halfOrFull - Indicates that this transaction program supports either half or full duplex conversations. |
| INT appcTpAdminConvSecReq | 1.3.6.1.2.1.34.3.1.3.1.1.14 | INTEGER | read-only | Indicates whether conversation-level security information is required on incoming attaches designating this TP name. Conversation-level security verification is always performed on those requests that include security information. yes - Indicates that conversation-level security information is required. ATTACHs designating the transaction program must carry a user_id and either a password or an already verified indicator. no - Indicates that no security information is required. ATTACHs designating the transaction program can omit or include security information. |
| INT appcTpAdminConvType | 1.3.6.1.2.1.34.3.1.3.1.1.12 | INTEGER | read-only | Specifies the conversation type (basic or mapped) that will be used by the TP. This value is verified upon receipt of an incoming attach. The acceptable values are: basic - Indicates that this transaction program supports basic conversations. mapped - Indicates that this transaction program supports mapped conversations. basicOrMapped - Indicates that this transaction program supports both basic and mapped conversations. |
| appcTpAdminEntry | 1.3.6.1.2.1.34.3.1.3.1.1 | not-accessible | Entry of APPC Local TP Information Table. | |
| STR appcTpAdminFileSpec | 1.3.6.1.2.1.34.3.1.3.1.1.3 | DisplayString | read-only | The local file specification of the transaction program. May be a zero-length string if not applicable. |
| I32 appcTpAdminInAttachTimeout | 1.3.6.1.2.1.34.3.1.3.1.1.6 | Integer32 | read-only | This object specifies the number of seconds incoming attaches will be queued waiting for an APPC program to issue a RECEIVE_ALLOCATE verb or for a CPI-C program to issue an Accept_Conversation (CMACCP) call. This parameter is meaningful only when appcTpAdminTpOperation has one of the following values: queuedOperatorStarted queuedOperatorPreloaded queuedAmStarted A value of zero indicates that there is no timeout. |
| I32 appcTpAdminInstLmt | 1.3.6.1.2.1.34.3.1.3.1.1.9 | Integer32 | read-only | The maximum number of concurrent instances of this transaction program that will be supported for a local LU. A value of zero indicates that there is no limit. |
| STR appcTpAdminLocLuName | 1.3.6.1.2.1.34.3.1.3.1.1.1 | DisplayString | not-accessible | The SNA name of the local LU to which this TP definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. The reserved value '*ALL' indicates that the TP definition applies to all local LUs, and not just to a single local LU. |
| INT appcTpAdminLongRun | 1.3.6.1.2.1.34.3.1.3.1.1.11 | INTEGER | read-only | Indicates whether this is a long-running transaction program (i.e., one that stays around even after the conversation goes away). |
| I32 appcTpAdminPipSubNum | 1.3.6.1.2.1.34.3.1.3.1.1.16 | Integer32 | read-only | Specifies the number of PIP subfields expected by the TP. |
| I32 appcTpAdminRcvAllocTimeout | 1.3.6.1.2.1.34.3.1.3.1.1.7 | Integer32 | read-only | This object specifies the number of seconds an APPC program's RECEIVE_ALLOCATE verb or a CPI-C program's Accept_Conversation (CMACCP) call will wait for an incoming attach to arrive. A value of zero indicates that there is no timeout. |
| STR appcTpAdminStartParm | 1.3.6.1.2.1.34.3.1.3.1.1.4 | DisplayString | read-only | A parameter string passed to the transaction program when it is started. May be a zero-length string if not supported. |
| INT appcTpAdminStatus | 1.3.6.1.2.1.34.3.1.3.1.1.10 | INTEGER | read-only | Indicates the status of the TP relative to starting execution when the local LU receives an allocation (ATTACH) request naming this program. enabled - the local LU can start the program. tempDisabled - the local LU cannot start the program. The local LU rejects the request with an indication that the TP is not available but retry is possible. permDisabled - the local LU cannot start the program. The local LU rejects the request with an indication that the TP is not available and retry is not possible. |
| INT appcTpAdminSyncLvl | 1.3.6.1.2.1.34.3.1.3.1.1.8 | INTEGER | read-only | Indicates the synchronization level or levels that the transaction program supports. The levels are defined as follows: none - allocation requests indicating a synchronization level of none are allowed to start the program. confirm - allocation requests indicating a synchronization level of confirm are allowed to start the program. syncpoint - allocation requests indicating a synchronization level of sync point are allowed to start the program. |
| appcTpAdminTable | 1.3.6.1.2.1.34.3.1.3.1 | not-accessible | APPC Local TP Table | |
| STR appcTpAdminTpName | 1.3.6.1.2.1.34.3.1.3.1.1.2 | DisplayString | not-accessible | The local transaction program name. This name is sent on an ATTACH remote allocation request. When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes). |
| INT appcTpAdminTpOperation | 1.3.6.1.2.1.34.3.1.3.1.1.5 | INTEGER | read-only | Specifies how the program will be started. other - Specifies that the program operation is none of the methods specified. It may be a product-specific method. queuedOperatorStarted - Specifies that one version of the program will be run at a time. If an incoming attach arrives and the program has not been started yet, APPC will issue a message to the operator to start the specified program. Subsequent attaches that arrive while the program is active will be queued. queuedOperatorPreloaded - Specifies that one version of the program will be run at a time. If an incoming attach arrives and the program has not been started yet, the Attach will be rejected. The APPC attach manager determines that a TP has started upon reception of an APPC RECEIVE_ALLOCATE verb, or a CPI-C Accept_Conversation (CMACCP) or Specify_Local_TP_Name (CMSLTP) call. No message is sent to the operator. Subsequent attaches that arrive while the program is active are queued. queuedAmStarted - Specifies that one version of the program will be run at a time and will be started by the APPC attach manager. Subsequent attaches that arrive while the program is active will be queued. nonqueuedAmStarted - Specifies that multiple copies of the program will be run at a time and will be started by the APPC attach manager. |
| INT appcTpAdminVerPip | 1.3.6.1.2.1.34.3.1.3.1.1.15 | INTEGER | read-only | Specifies whether the number of PIP (Program Initialization Parameters) subfields should be verified against the number expected (appcTpAdminPipSubNum). |
| appcTpConfGroup | 1.3.6.1.2.1.34.3.2.2.5 | A collection of objects providing the instrumentation of APPC Transaction Programs. | ||
| TIK appcUpTime | 1.3.6.1.2.1.34.3.1.1.3.1 | TimeTicks | read-only | The time, in hundredths of a second, since the APPC portion of the system was last reinitialized. |
RFC description
APPC (Advanced Program-to-Program Communication) LU and session management for SNA.
Start monitoring SNA/APPC gateway or protocol converter with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.