All MIBs › ALCATEL-IND1-SYSTEM-MIB
Organization: Alcatel-Lucent
Last Updated: 2011--0-1-
Category: Device Management, Vendor: Alcatel-Lucent
Description: Alcatel OmniSwitch system MIB for managing hostname, location, contact, system time, and global operational parameters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ALCATEL-IND1-SYSTEM-MIB?
ALCATEL-IND1-SYSTEM-MIB is an Alcatel-Lucent OmniSwitch proprietary "System Subsystem" MIB providing chassis-wide identification and operational configuration, such as hostname, physical location, administrative contact, system time, and other global operational parameters. Although no sample objects were supplied, by its stated purpose it exposes basic system-identity and time-configuration data comparable to the standard SNMPv2-MIB system group, with Alcatel-specific extensions for global operational settings. Its monitoring value is primarily basic software/system-status visibility -- confirming the device's configured system time, name, and contact/location metadata are correct, which underpins fault correlation (accurate timestamps) and inventory/asset tracking across a fleet of switches. It complements the standard SNMPv2-MIB system group (sysName, sysLocation, sysContact, sysUpTime) rather than replacing it, adding Alcatel-proprietary global parameters alongside those standard objects. It is typically used across Alcatel/Alcatel-Lucent OmniSwitch deployments for basic identification, time synchronization verification, and global feature toggling, and administrators can download the ALCATEL-IND1-SYSTEM-MIB file to load it into their MIB browser for this purpose.
IPNetwork Monitor allows you to monitor SNMP objects defined in ALCATEL-IND1-SYSTEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Alcatel/Alcatel-Lucent OmniSwitch enterprise switch
Monitoring Examples
Because no sample objects were provided, a specific object-level scenario cannot be given with confidence; based on the module description, an operator would typically check the device's configured system time and hostname/location/contact fields to confirm the switch's identity and clock are correctly set, which matters for accurate fault-log timestamps across a fleet.
What Can Be Monitored
- system hostname
- system location/contact
- system time configuration
- global operational parameters
This MIB depends on
Related MIBs
Imported Objects
From ALCATEL-IND1-BASE
| hardentIND1System | OBJECT-IDENTITY |
From IPV6-TC
| Ipv6Address |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| alcatelIND1SystemMIB | 1.3.6.1.4.1.6486.801.1.1.1.2.1 | This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): For the Birds Of Prey Product Line Proprietary System Subsystem. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE | ||
| alcatelIND1SystemMIBCompliance | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2.2.1 | Compliance statement for Alcatel BOP Proprietary System Subsystem. | ||
| alcatelIND1SystemMIBCompliances | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2.2 | Branch For Alcatel IND BOP Proprietary System Subsystem Compliance Statements. | ||
| alcatelIND1SystemMIBConformance | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2 | Branch For Alcatel IND BOP Proprietary System Subsystem Conformance Information. | ||
| alcatelIND1SystemMIBGroups | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2.1 | Branch For Alcatel IND BOP Proprietary System Subsystem Units Of Conformance. | ||
| alcatelIND1SystemMIBObjects | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1 | Branch For BOP Proprietary System Subsystem Managed Objects. | ||
| IP systemBootNetwork | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.2.1 | IpAddress | read-only | this object is the base IP address of the EMP for this CMM |
| IP systemBootNetworkGateway | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.2.2 | IpAddress | read-only | this object is the gateway of the EMP for this CMM |
| IP systemBootNetworkNetmask | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.2.3 | IpAddress | read-only | This is the Netmask of the EMP that is used when this CMM boots. |
| systemBootParams | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.2 | |||
| systemBootParamsGroup | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2.1.2 | Group all the system boot parameters together | ||
| systemDNS | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.7 | |||
| STR systemDNSDomainName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.7.2 | SnmpAdminString | read-create | current domain name used by the Domain Name Service |
| ENA systemDNSEnableDnsResolver | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.7.1 | Enable | read-create | Global Domain Name Service enable/disable |
| systemDNSGroup | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2.1.7 | Group all the systemDNS parameters together | ||
| IP systemDNSNsAddr1 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.7.3 | IpAddress | read-create | 1st part of address used by the Domain Name Service |
| IP systemDNSNsAddr2 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.7.4 | IpAddress | read-create | 2nd part of address used by the Domain Name Service |
| IP systemDNSNsAddr3 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.7.5 | IpAddress | read-create | 3rd part of address used by the Domain Name Service |
| ADR systemDNSNsIPv6Addr1 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.7.6 | Ipv6Address | read-create | IPv6 address of the Primary DNS server |
| ADR systemDNSNsIPv6Addr2 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.7.7 | Ipv6Address | read-create | IPv6 address of the Secondary DNS server |
| ADR systemDNSNsIPv6Addr3 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.7.8 | Ipv6Address | read-create | IPv6 address of the third DNS server |
| systemFileSystem | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4 | |||
| STR systemFileSystemDirectoryDateTime | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.3 | SnmpAdminString | read-only | the date and time (in system format) of the last access to this directory |
| STR systemFileSystemDirectoryName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.2 | SnmpAdminString | read-write | The name of a file system directory. This object is used in conjunction with an Action command. The Action command will set this directory name to the name of a specific directory. Information for all of the files in that directory will then be read from the file system and the appropriate values written in the entries in the systemFileSystemFile table. All this is being done to give snmp access to the file system files. |
| systemFileSystemEntry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.1.1 | not-accessible | A row in the system file system table | |
| INT systemFileSystemFileAttr | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.4.1.5 | INTEGER | read-only | attributes of this file |
| STR systemFileSystemFileDateTime | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.4.1.6 | SnmpAdminString | read-only | the modification date and time of a file |
| systemFileSystemFileEntry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.4.1 | not-accessible | A row in the system file system File table | |
| U32 systemFileSystemFileIndex | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.4.1.1 | Unsigned32 | read-only | Index to a specific file system File. |
| STR systemFileSystemFileName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.4.1.2 | SnmpAdminString | read-only | The name of a file system File |
| U32 systemFileSystemFileSize | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.4.1.4 | Unsigned32 | read-only | size of this file |
| systemFileSystemFileTable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.4 | not-accessible | system file system File table for this CMM. This table is used by an Action command which will populate it with file information read from the files in the specified directory. | |
| SYS systemFileSystemFileType | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.4.1.3 | SystemFileType | read-only | The Type of a file system File |
| U32 systemFileSystemFreeSpace | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.1.1.3 | Unsigned32 | read-only | the free space in octets of this file system |
| systemFileSystemGroup | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2.1.5 | Group all the system flash file parameters together | ||
| FIL systemFileSystemIndex | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.1.1.1 | FileSystemIndex | read-only | Index to a specific file system. |
| STR systemFileSystemName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.1.1.2 | SnmpAdminString | read-only | The name of the file system. |
| systemFileSystemTable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.4.1 | not-accessible | system file system table for this CMM. | |
| systemHardware | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3 | |||
| STR systemHardwareBackupMiniBootVersion | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.13 | SnmpAdminString | read-only | A string that identifies the backup miniboot version. |
| INT systemHardwareBootCpuType | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.6 | INTEGER | read-only | Indicates the manufacturer and model number of the CPU. Currently, only two types of processors are enumerated. |
| STR systemHardwareBootRomVersion | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.12 | SnmpAdminString | read-only | A string that identifies the boot rom version |
| STR systemHardwareCpldVersion | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.16 | SnmpAdminString | read-only | A string that identifies the CPLD version. |
| STR systemHardwareDefaultMiniBootVersion | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.14 | SnmpAdminString | read-only | A string that identifies the default miniboot version. |
| INT systemHardwareFlashMfg | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.1 | INTEGER | read-only | This object identifies the manufacturer of the Flash memory used on this product. toshiba(7) is for hawk only. The reason 7 is used is because 5 is already used for micron and 6 is for kingston. toshiba, sandisk, and sst are compact flashes for the hawk only. |
| U32 systemHardwareFlashSize | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.2 | Unsigned32 | read-only | This object identifies the size of the flash memory available on this CMM. It is the total flash hardware memory and does not indicate how much of the memory is free, used, etc. |
| U32 systemHardwareFpgaVersion | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.11.1.2 | Unsigned32 | read-only | This is the major version of one of the FPGA devices on this CMM. refer to the systemHardwareMinorFpgaVersion for the minor number. |
| systemHardwareFpgaVersionEntry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.11.1 | not-accessible | a row in the systemHardwareFpgaVersionTable | |
| I32 systemHardwareFpgaVersionIndex | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.11.1.1 | Integer32 | read-only | This is the index to one of the FPGA versions on this CMM |
| systemHardwareFpgaVersionTable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.11 | not-accessible | This table contains the FPGA version for each FPGA on this CMM | |
| systemHardwareGroup | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2.1.3 | Group all the system Hardware Data together | ||
| T/F systemHardwareJumperForceUartDefaults | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.8 | TruthValue | read-only | This object identifies whether the Force Uart Defaults Jumper on this CMM is set: True(1), False(2) |
| T/F systemHardwareJumperInterruptBoot | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.7 | TruthValue | read-only | This object identifies whether the Interrupt Boot Jumper on this CMM is set: True(1), False(2) |
| T/F systemHardwareJumperRunExtendedMemoryDiagnostics | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.9 | TruthValue | read-only | This object identifies whether the Run Extended Memory Diagnostics Jumper on this CMM is set: True(1), False(2) |
| T/F systemHardwareJumperSpare | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.10 | TruthValue | read-only | This object identifies whether the Spare Jumper on this CMM is set: True(1), False(2) |
| INT systemHardwareMemoryMfg | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.3 | INTEGER | read-only | This object identifies the manufacturer of the RAM memory used on this CMM. |
| U32 systemHardwareMemorySize | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.4 | Unsigned32 | read-only | This object identifies the size of the RAM memory available on this CMM. It is the total RAM hardware memory and does not indicate how much of the memory is free, used, etc. |
| STR systemHardwareMinorFpgaVersion | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.15 | SnmpAdminString | read-only | A string that identifies the minor FPGA version. Refer to the systemHardwareFpgaVersion for the major FPGA version number. |
| T/F systemHardwareNVRAMBatteryLow | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.5 | TruthValue | read-only | This object identifies the whether the NVRAM battery is low. true(1), false(2) |
| STR systemHardwareProdRegId | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.18 | SnmpAdminString | read-only | A string that identifies the product ID register |
| STR systemHardwareRevisionRegister | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.19 | SnmpAdminString | read-only | A string that identifies the hardware revision register |
| STR systemHardwareUbootMinibootVersion | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.21 | SnmpAdminString | read-only | A string that identifies the Uboot-miniboot version. |
| STR systemHardwareUbootVersion | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.17 | SnmpAdminString | read-only | A string that identifies the Uboot version. |
| STR systemHardwareXfpId | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.3.20 | SnmpAdminString | read-only | A string that identifies the XFP ID |
| systemMicrocode | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1 | |||
| systemMicrocodeGroup | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2.1.1 | Group all the system microcode objects together | ||
| STR systemMicrocodePackageDescription | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1.1.1.6 | SnmpAdminString | read-only | The description of the microcode package |
| STR systemMicrocodePackageDirectory | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1.1.1.2 | SnmpAdminString | not-accessible | The directory name under flash where the microcode package is found. Directories with names longer than 108 characters will be skipped. |
| U32 systemMicrocodePackageDirectoryIndex | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1.1.1.1 | Unsigned32 | not-accessible | The package index for directories. Values 1-4 are pre-defined as: loaded(1), certified(2), working(3), issu(4). Values 5+ are user working directories in /flash assigned by the system. Values 5+ remain associated with a directory until reboot, takeover, the directory no longer contains valid images or the directory no longer exists. |
| systemMicrocodePackageEntry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1.1.1 | not-accessible | a row in the microcode package table | |
| U32 systemMicrocodePackageIndex | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1.1.1.3 | Unsigned32 | not-accessible | The index to the package sub table in the microcode table |
| STR systemMicrocodePackageName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1.1.1.5 | SnmpAdminString | read-only | The name of the microcode package |
| U32 systemMicrocodePackageSize | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1.1.1.8 | Unsigned32 | read-only | The size of the microcode package |
| INT systemMicrocodePackageStatus | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1.1.1.7 | INTEGER | read-only | The status of the microcode package |
| systemMicrocodePackageTable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1.1 | not-accessible | the microcode package table | |
| STR systemMicrocodePackageVersion | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.1.1.1.4 | SnmpAdminString | read-only | The version of the microcode package (Fos.img, Fbase.img, etc.) |
| systemServices | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5 | |||
| INT systemServicesAction | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.24 | INTEGER | read-write | This object identifies which of the above Actions is to be performed by the System Services Application. Most Actions require one or more parameters be set before the Action is executed. systemServicesAction - 26 for bootrom, 27 for default miniboot, and 28 for backup miniboot use systemServicesArg1 for name of the file scp- the first 2 arguments are going to be used. Set arg 1 with the source and the arg 2 with the destination file(s). E.g. scp LocalDir/testfileX.txt admin@10.255.11.1:RemoteDir/testfileX.txt For mount and umount, systemServicesArg1 specifies the mount point (such as /uflash). For newfs, systemServicesArg1 contains the name of the file-system (/uflash or /flash) which will be created. On /uflash, a FAT16 file system is created with long name naming conventions. For fsck, systemServicesArg1 contains the name of the file-system (/uflash or /flash) which will be checked and systemServicesArg2 will contain the string repair or no-repair depending on if autocorrection is requested. To see all file systems currently mounted, refer to the systemFileSystemTable. For backup and restore, systemServicesArg1 contains the archive name and systemServicesArg2 through Arg9 contains the directories and/or files to be archived/extracted. For newfs, fsck, backup and restore, the systemServicesActionPercentComplete variable can be inspected to see a progress indication. |
| COM systemServicesActionPercentComplete | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.35 | CommandPercentComplete | read-only | This object identifies the percent completion of the currently executing systemServicesAction. |
| INT systemServicesArchiveAttr | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.37.1.5 | INTEGER | read-only | The attributes of a file in the backup archive file. |
| systemServicesArchiveEntry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.37.1 | not-accessible | A row in the system services archive table. | |
| U32 systemServicesArchiveIndex | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.37.1.1 | Unsigned32 | read-only | Index to a specific entry in the backup archive file. |
| STR systemServicesArchiveName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.37.1.2 | SnmpAdminString | read-only | The name of a file in the backup archive file. |
| U32 systemServicesArchiveSize | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.37.1.4 | Unsigned32 | read-only | The size of a file in the backup archive file. |
| systemServicesArchiveTable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.37 | not-accessible | This table contains the contents of a backup archive. This table is used by the restore action command to display (rather than backup) an archive. The restore command will populate this table with archive information read from the archive specified by the systemServicesAction restore command. This is done as follows. Set the systemServicesArg1 object to the archive name to be read. Set the systemServicesArg2 object to the string: display-only. Set the systemServicesAction object to restore. Then read this table. | |
| SYS systemServicesArchiveType | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.37.1.3 | SystemFileType | read-only | The type of a file in the backup archive file. |
| STR systemServicesArg1 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.15 | SnmpAdminString | read-write | the 1st argument for system services action routines |
| STR systemServicesArg2 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.16 | SnmpAdminString | read-write | the 2nd argument for system services action routines |
| STR systemServicesArg3 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.17 | SnmpAdminString | read-write | the 3rd argument for system services action routines |
| STR systemServicesArg4 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.18 | SnmpAdminString | read-write | the 4th argument for system services action routines |
| STR systemServicesArg5 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.19 | SnmpAdminString | read-write | the 5th argument for system services action routines |
| STR systemServicesArg6 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.20 | SnmpAdminString | read-write | the 6th argument for system services action routines |
| STR systemServicesArg7 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.21 | SnmpAdminString | read-write | the 7th argument for system services action routines |
| STR systemServicesArg8 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.22 | SnmpAdminString | read-write | the 8th argument for system services action routines |
| STR systemServicesArg9 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.23 | SnmpAdminString | read-write | the 9th argument for system services action routines |
| STR systemServicesCurrentArchivePathName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.36 | SnmpAdminString | read-write | This object identifies the archive currently being read via the systemServicesArchiveTable. This object is the complete pathname to the archive and must be set prior to reading the systemServicesArchiveTable. |
| STR systemServicesDate | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.1 | SnmpAdminString | read-write | This object contains the current System Date in the following format: MM/DD/YYYY |
| ENA systemServicesEnableDST | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.13 | Enable | read-write | This object enables and disables the DST. |
| systemServicesGroup | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2.1.4 | Group all the system services parameters together | ||
| ENA systemServicesKtraceEnable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.27 | Enable | read-write | enables/disables the Ktrace facility |
| SEV systemServicesKtraceLevel | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.32.1.2 | SeverityLevel | read-write | the ktrace level for a specific Application ID |
| APP systemServicesKtraceLevelAppId | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.32.1.1 | AppIdIndex | read-only | the index into the ktrace level table |
| systemServicesKtraceLevelEntry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.32.1 | not-accessible | A row in the system services ktrace level table. There is one entry for each possible Application ID | |
| systemServicesKtraceLevelTable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.32 | not-accessible | the table of Ktrace severity level settings | |
| ENA systemServicesMemMonitorEnable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.31 | Enable | read-write | disables/enables the kernel Memory Monitor feature |
| U32 systemServicesResultCode | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.25 | Unsigned32 | read-only | the result of a system services application |
| STR systemServicesResultString | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.26 | SnmpAdminString | read-only | the string result of a system services application |
| ENA systemServicesSystraceEnable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.28 | Enable | read-write | enables/disables the Systrace facility |
| SEV systemServicesSystraceLevel | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.33.1.2 | SeverityLevel | read-write | the Systrace level for a specific Application ID. |
| APP systemServicesSystraceLevelAppId | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.33.1.1 | AppIdIndex | read-only | the Systrace level for a specific Application ID. |
| systemServicesSystraceLevelEntry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.33.1 | not-accessible | A row in the system services systrace level table. There is one entry for each possible Application ID | |
| systemServicesSystraceLevelTable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.33 | not-accessible | the table of Systrace severity level settings | |
| STR systemServicesTime | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.2 | SnmpAdminString | read-write | This object contains the current System Time in the following format: HH:MM:SS |
| STR systemServicesTimezone | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.3 | SnmpAdminString | read-write | This object contains the current Hour Offset from UTC in the following format: -13:00 to +12:00 OR a well known timezone (PST,CST,etc.) |
| U32 systemServicesTimezoneEndDay | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.10 | Unsigned32 | read-write | Sunday, Monday, Tues... = 1,2,3,4,5,6,7 |
| U32 systemServicesTimezoneEndMonth | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.11 | Unsigned32 | read-write | January, February, march... = 1,2,3,4,5,6,7,8,9,10,11,12 |
| U32 systemServicesTimezoneEndTime | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.12 | Unsigned32 | read-write | 2:00, 3:00, 4:00... = 200, 300, 400, etc. |
| U32 systemServicesTimezoneEndWeek | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.9 | Unsigned32 | read-write | first, second, third, fourth, fifth, last = 1,2,3,4,5,6 |
| U32 systemServicesTimezoneOffset | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.8 | Unsigned32 | read-write | 60 minutes = 60 |
| U32 systemServicesTimezoneStartDay | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.5 | Unsigned32 | read-write | Sunday, Monday, Tues... = 1,2,3,4,5,6,7 |
| U32 systemServicesTimezoneStartMonth | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.6 | Unsigned32 | read-write | January, February, march... = 1,2,3,4,5,67,8,9,10,11,12 |
| U32 systemServicesTimezoneStartTime | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.7 | Unsigned32 | read-write | 2:00, 3:00, 4:00... = 200, 300, 400, etc. |
| U32 systemServicesTimezoneStartWeek | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.4 | Unsigned32 | read-write | first, second, third, fourth, fifth, last = 1,2,3,4,5,6 |
| U32 systemServicesTtyColumns | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.30 | Unsigned32 | read-only | the number of tty columns for a console screen |
| U32 systemServicesTtyLines | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.29 | Unsigned32 | read-only | the number of tty lines for a console screen |
| ENA systemServicesUsbAutoCopyEnable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.39 | Enable | read-write | disable/enable the USB auto-copy facility |
| ENA systemServicesUsbEnable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.38 | Enable | read-write | disable/enable the USB interface |
| ENA systemServicesUsbMounted | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.40 | Enable | read-only | determinse if usb is mounted |
| STR systemServicesWorkingDirectory | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.14 | SnmpAdminString | read-write | This object contains the current file system working directory for this CMM. For example, /flash/certified |
| systemSwitchLogging | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6 | |||
| APP systemSwitchLoggingApplicationAppId | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.7.1.1 | AppIdIndex | read-only | A specific application ID which has a registered application associated with it. This application ID is used as an index into the application table. |
| STR systemSwitchLoggingApplicationAppName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.7.1.4 | SnmpAdminString | read-only | Application name in an entry in the table |
| APP systemSwitchLoggingApplicationSubAppId | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.7.1.2 | AppIdIndex | read-only | A specific sub-application ID which belongs to a registered application associated with it. This sub-application ID is used as part of the index into the application table. |
| SEV systemSwitchLoggingApplicationSubAppLevel | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.7.1.6 | SeverityLevel | read-only | The severity level of the specific sub-application ID. |
| STR systemSwitchLoggingApplicationSubAppName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.7.1.5 | SnmpAdminString | read-only | The name of the specific sub-application ID. |
| I32 systemSwitchLoggingApplicationSubAppVrfLevelIndex | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.7.1.3 | Integer32 | read-only | The specific sub-application's VRF severity level. This severity level is used as part of the index into the application table. |
| STR systemSwitchLoggingApplicationSubAppVrfLevelString | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.7.1.7 | SnmpAdminString | read-only | A string with comma-delimited VRF IDs or ranges of VRF IDs that belong to this sub-application's VRF severity level. |
| systemSwitchLoggingApplicationTable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.7 | not-accessible | The table of switch logging registered applications,one for each Application ID | |
| STR systemSwitchLoggingAppName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.17 | SnmpAdminString | read-write | Application name used as an index into the table |
| U32 systemSwitchLoggingClear | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.8 | Unsigned32 | read-write | Enable clearing of switch logging entries |
| ENA systemSwitchLoggingConsole | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.6 | Enable | read-write | Enable/disable switch logging to the console |
| SEV systemSwitchLoggingConsoleLevel | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.13 | SeverityLevel | read-create | Messages whose severity level is equal to or more severe than this value will be displayed to the console. |
| ENA systemSwitchLoggingDebug | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.20 | Enable | read-write | Global switch logging enable/disable debug information |
| ENA systemSwitchLoggingDuplicateDetect | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.18 | Enable | read-write | Global switch logging enable/disable duplicate detection |
| ENA systemSwitchLoggingEnable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.2 | Enable | read-write | Global switch logging enable/disable |
| U32 systemSwitchLoggingFileSize | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.9 | Unsigned32 | read-write | Set size of swlog logging file |
| ENA systemSwitchLoggingFlash | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.3 | Enable | read-write | Enable/disable switch logging to flash |
| systemSwitchLoggingGroup | 1.3.6.1.4.1.6486.801.1.1.1.2.1.2.1.6 | Group all the switch logging parameters together | ||
| AGE systemSwitchLoggingHashAgeLimit | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.22 | AgeLimit | read-write | Global switch logging Hash Table Age Limit |
| I32 systemSwitchLoggingHostCount | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.12 | Integer32 | read-only | The number of remote hosts currently defined. |
| systemSwitchLoggingHostEntry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.10.1 | not-accessible | A remote switch logging server entry. | |
| IP systemSwitchLoggingHostIpAddr | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.10.1.1 | IpAddress | read-only | The IP Address of a remote host that can be used to send switch logging records to. |
| I32 systemSwitchLoggingHostPort | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.10.1.2 | Integer32 | read-create | The port number of a remote host that can be used to send switch logging records to. |
| ROW systemSwitchLoggingHostStatus | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.10.1.3 | RowStatus | read-create | Provides the ability to add or remove a remote host entry. |
| systemSwitchLoggingHostTable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.10 | not-accessible | The table of switch logging remote hosts. | |
| ENA systemSwitchLoggingHostUserCommandHost | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.10.1.4 | Enable | read-create | Indicates whether this host may receive user command data. |
| systemSwitchLoggingHostv6Entry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.11.1 | not-accessible | A remote switch logging server entry. | |
| ADR systemSwitchLoggingHostv6IpAddr | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.11.1.1 | Ipv6Address | read-only | The IP Address of a remote host that can be used to send switch logging records to. |
| I32 systemSwitchLoggingHostv6Port | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.11.1.2 | Integer32 | read-create | The port number of a remote host that can be used to send switch logging records to. |
| ROW systemSwitchLoggingHostv6Status | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.11.1.3 | RowStatus | read-create | Provides the ability to add or remove a remote host entry. |
| systemSwitchLoggingHostv6Table | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.11 | not-accessible | The table of switch logging remote hosts. | |
| ENA systemSwitchLoggingHostv6UserCommandHost | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.11.1.4 | Enable | read-create | Indicates whether this host may receive user command data. |
| STR systemSwitchLoggingHostv6VrfName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.11.1.5 | SnmpAdminString | read-create | The name or number of the VRF to be used to send switch logging records to. |
| STR systemSwitchLoggingHostVrfName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.10.1.5 | SnmpAdminString | read-create | The name or number of the VRF to be used to send switch logging records to. |
| SWI systemSwitchLoggingIndex | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.1 | SwitchLoggingIndex | read-only | A small positive integer used to identify a switch logging output |
| SEV systemSwitchLoggingLevel | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.16 | SeverityLevel | read-write | The logging level for a specific application id. |
| systemSwitchLoggingLevelEntry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.7.1 | not-accessible | A row in the system switch logging application table | |
| STR systemSwitchLoggingLibraryName | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.25 | SnmpAdminString | read-write | Library name used as an index into the table of registered libraries |
| ENA systemSwitchLoggingLoopback0 | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.26 | Enable | read-write | Enable/disable switch logging using Loopback0 interface as the source ip address when logging to syslog server |
| ENA systemSwitchLoggingPreamble | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.19 | Enable | read-write | Global switch logging enable/disable printing preamble |
| ENA systemSwitchLoggingSocket | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.4 | Enable | read-write | Enable/disable switch logging to a socket |
| IP systemSwitchLoggingSocketIpAddr | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.5 | IpAddress | read-write | The IP Address of a remote host that can be used to send switch logging records to as an option |
| APP systemSwitchLoggingSubAppNbr | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.24 | AppIdIndex | read-write | The subapplication number of a given application |
| SYS systemSwitchLoggingSysLogFacilityId | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.15 | SysLogFacilityId | read-write | This textual convention enumerates the facilities that originate syslog messages. The Facilities of syslog messages are numerically coded with decimal values. Some of the operating system daemons and processes are traditionally designated by the Facility values given below. Daemons and processes that do not have an explicitly assigned Facility may use any of the 'local use' Facilities or they may use the 'user-level' Facility. For interoperability and backwards compatibility reasons, mapping specified in this document between a label which represents a Facility and the value which represents the corresponding code, is normative. So the mapping from a label configured by operators in syslog.conf or equivalent will consistently map to the same Facility code regardless of implementation, but the label itself is often semantically meaningless, because it is impractical to attempt to enumerate all possible facilities, and the enumeration (label and corresponding value) that is used by an actual Facility is, and has historically been, implementation-dependent. For example, the foobar application might log messages as having come from local7, even though there is no 'local' process on the device, and the operator can configure syslog.conf to have local7.critical messages be relayed, even though there might be multiple facilities using Facility local7. This is typical current practice, and originators, relays and collectors know how to handle this situation. For improved accuracy, the foobar application can also include an APPNAME Structured Data Element. |
| ENA systemSwitchLoggingTty | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.23 | Enable | read-write | Enable/disable switch logging to tty |
| ENA systemSwitchLoggingUserCommandStatus | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.14 | Enable | read-create | User commands will be logged to remote hosts when enabled. |
| VRF systemSwitchLoggingVrf | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.6.21 | VrfId | read-write | Global switch logging subapplicastion VRF ID |
| INT systemUpdateErrorCode | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.34.1.3 | INTEGER | read-only | Error codes for done_nok. |
| I32 systemUpdateIndex | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.34.1.1 | Integer32 | not-accessible | The index to the CMM for which status is required. |
| INT systemUpdateStatus | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.34.1.2 | INTEGER | read-only | Status of a firmware update. In the case of doneNok, further information can be obtained from systemUpdateErrorCode. |
| systemUpdateStatusEntry | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.34.1 | not-accessible | A row in the update status table. | |
| systemUpdateStatusTable | 1.3.6.1.4.1.6486.801.1.1.1.2.1.1.5.34 | not-accessible | Provides update status for firmware updates |
RFC description
Provides system management for Alcatel-Lucent Birds of Prey enterprise switches and routers.
Start monitoring Alcatel-Lucent Enterprise OmniSwitch switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.