All MIBs › ALANTEC-MIB
Category: Network Interfaces
Description: Alantec (Nortel) proprietary MIB for managing fast Ethernet switch port configuration and statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ALANTEC-MIB?
ALANTEC-MIB is a legacy proprietary MIB originally developed by Alantec (later acquired by FORE Systems/Nortel Networks) for managing fast Ethernet switch hardware, covering per-port configuration and traffic statistics on the switch. No object or table names were available for this module, so its precise data model cannot be fully detailed, but vendor Ethernet switch MIBs of this era typically expose per-port administrative/operational status, speed/duplex settings, and traffic counters alongside chassis and module identification. In terms of monitoring, such a MIB would typically support tracking port link status, traffic/error counters, and basic chassis health, letting an administrator detect a down or errored port on the switch. It is a legacy proprietary module predating widespread adoption of the standard IF-MIB and EtherLike-MIB, though modern deployments would likely favor those standards over this one. It would be deployed only on legacy Alantec/Nortel fast Ethernet switch hardware still in service in older network environments. Network engineers evaluating or troubleshooting this functionality can download the ALANTEC-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ALANTEC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Alantec fast Ethernet switch
- Nortel-acquired Alantec switch hardware
Monitoring Examples
No object or table names are available for this MIB in the provided source, so specific OIDs cannot be cited; typical usage would involve polling per-port link status and traffic counters, but the actual object identifiers cannot be confirmed from the available data.
What Can Be Monitored
- port link status
- port speed/duplex configuration
- port traffic statistics
- switch chassis identification
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| PhysAddress |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| alantec | 1.3.6.1.4.1.390 | |||
| INT alArpAge | 1.3.6.1.4.1.390.2.6.2 | INTEGER | read-write | Timeout in minutes for aging ARP entries; when set to zero, set-arpage is turned off. |
| INT alArpDynInvalidOpcodes | 1.3.6.1.4.1.390.2.6.10 | INTEGER | read-only | Invalid Opcodes Received. |
| INT alArpDynRepliesRcvd | 1.3.6.1.4.1.390.2.6.9 | INTEGER | read-only | Replies Received. |
| INT alArpDynRepliesSent | 1.3.6.1.4.1.390.2.6.12 | INTEGER | read-only | Replies Sent. |
| INT alArpDynReqsRcvd | 1.3.6.1.4.1.390.2.6.8 | INTEGER | read-only | Requests Received. |
| INT alArpDynRequestsSent | 1.3.6.1.4.1.390.2.6.11 | INTEGER | read-only | Requests Sent. |
| alArpProxyTable | 1.3.6.1.4.1.390.2.6.13 | not-accessible | Per port proxy arp enable/disable | |
| INT alArpStatInvalidOpcodes | 1.3.6.1.4.1.390.2.6.5 | INTEGER | read-only | Invalid Opcodes Received. |
| INT alArpStatRepliesRcvd | 1.3.6.1.4.1.390.2.6.4 | INTEGER | read-only | Replies Received. |
| INT alArpStatRepliesSent | 1.3.6.1.4.1.390.2.6.7 | INTEGER | read-only | Replies Sent. |
| INT alArpStatReqsRcvd | 1.3.6.1.4.1.390.2.6.3 | INTEGER | read-only | Requests Received. |
| INT alArpStatRequestsSent | 1.3.6.1.4.1.390.2.6.6 | INTEGER | read-only | Requests Sent. |
| INT alArpTableClear | 1.3.6.1.4.1.390.2.6.1 | INTEGER | read-write | When set, clears the ARP table. |
| alat | 1.3.6.1.4.1.390.2.7 | |||
| INT alBrFlushCache | 1.3.6.1.4.1.390.2.2.3 | INTEGER | read-write | When set, flushes the cache. |
| alBrGroupEntry | 1.3.6.1.4.1.390.2.2.13.1 | not-accessible | ||
| alBrGroupTable | 1.3.6.1.4.1.390.2.2.13 | not-accessible | ||
| albridge | 1.3.6.1.4.1.390.2.2 | |||
| alBridgeEntry | 1.3.6.1.4.1.390.2.2.1.1 | not-accessible | Information about a specific unicast MAC address for which the bridge has some forwarding and/or filtering information. | |
| MAC alBridgeEntryAddress | 1.3.6.1.4.1.390.2.2.1.1.1 | MacAddress | read-only | The MAC address for which the bridge has forwarding and/or filtering information. |
| INT alBridgeEntryFlags | 1.3.6.1.4.1.390.2.2.1.1.5 | INTEGER | read-only | The status of this entry. |
| INT alBridgeEntryLink | 1.3.6.1.4.1.390.2.2.1.1.3 | INTEGER | read-only | The link number on the port on which a frame having as ource address equal to the value of the corresponding instance of alBridgeEntryAddress has been seen. Only applies to the UTP port type. |
| INT alBridgeEntryPort | 1.3.6.1.4.1.390.2.2.1.1.2 | INTEGER | read-only | The port number of the port on which a frame having a source address equal to the value of the corresponding instance of alBridgeEntryAddress has been seen. |
| INT alBridgeEntryRule | 1.3.6.1.4.1.390.2.2.1.1.4 | INTEGER | read-write | The rule number that is applied to packets that are forwarded to or from this address. |
| INT alBridgeIpBridging | 1.3.6.1.4.1.390.2.2.9 | INTEGER | read-write | When set to enable(1), enables the IP bridging and if set to disable(0), disables the IP bridging. |
| INT alBridgePPControl | 1.3.6.1.4.1.390.2.2.6 | INTEGER | read-write | When set to 0 , disables the port to port collection of the stats; when set to 1, enables the port to port stats collection; when set to 2, clears the port to port stats. |
| INT alBridgeStatsClear | 1.3.6.1.4.1.390.2.2.5 | INTEGER | read-write | When set, clears the statistics for the bridge. |
| INT alBridgeSTPControl | 1.3.6.1.4.1.390.2.2.14 | INTEGER | read-write | When set to 0 , disables the spanning tree. set to 1, enables the spanning tree. |
| alBridgeTable | 1.3.6.1.4.1.390.2.2.1 | not-accessible | A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame. | |
| INT alBridgeTblClear | 1.3.6.1.4.1.390.2.2.2 | INTEGER | read-write | When set, clears the Bridge table. |
| alBrRuleTable | 1.3.6.1.4.1.390.2.2.11 | not-accessible | Per rule information | |
| alBrRuleToNodeEntry | 1.3.6.1.4.1.390.2.2.12.1 | not-accessible | ||
| alBrRuleToNodeTable | 1.3.6.1.4.1.390.2.2.12 | not-accessible | ||
| alBrTemplateTable | 1.3.6.1.4.1.390.2.2.10 | not-accessible | Per template information | |
| alchassis | 1.3.6.1.4.1.390.1.3.1 | |||
| INT alChassisType | 1.3.6.1.4.1.390.2.1.1 | INTEGER | read-only | The model type of the PowerHub |
| INT alCpuSlot | 1.3.6.1.4.1.390.1.3.1.5 | INTEGER | read-only | The slot number in which the packet engine resides |
| aldecnet | 1.3.6.1.4.1.390.2.8 | |||
| STR alFcpuOnePromVer | 1.3.6.1.4.1.390.2.1.6 | DisplayString | read-only | PROM software version of F-bus CPU for the first FDDI board. |
| STR alFcpuOneRtVer | 1.3.6.1.4.1.390.2.1.4 | DisplayString | read-only | Runtime software version of F-bus CPU for the first FDDI board. |
| STR alFcpuTwoPromVer | 1.3.6.1.4.1.390.2.1.7 | DisplayString | read-only | PROM software version of F-bus CPU for the second FDDI board. |
| STR alFcpuTwoRtVer | 1.3.6.1.4.1.390.2.1.5 | DisplayString | read-only | Runtime software version of F-bus CPU for the second FDDI board. |
| alFiberStatsTable | 1.3.6.1.4.1.390.2.3.7 | not-accessible | Per port fiber stats and Fiber Security | |
| alip | 1.3.6.1.4.1.390.2.6 | |||
| alIpInterfaceEntry | 1.3.6.1.4.1.390.2.6.19.1 | not-accessible | ||
| alIpInterfaceTable | 1.3.6.1.4.1.390.2.6.19 | not-accessible | Interface table corresponding to the command - interface-table. | |
| alIpRtCacheEntry | 1.3.6.1.4.1.390.2.6.20.1 | not-accessible | IP Route cache for each port | |
| alIpRtCacheTable | 1.3.6.1.4.1.390.2.6.20 | not-accessible | IP Route Cache for all ports | |
| alIpRuleTable | 1.3.6.1.4.1.390.2.6.15 | not-accessible | Per template information | |
| alIpTemplateTable | 1.3.6.1.4.1.390.2.6.14 | not-accessible | Per template information | |
| alipx | 1.3.6.1.4.1.390.2.9 | |||
| alLinkControlTable | 1.3.6.1.4.1.390.2.3.5 | not-accessible | Per link stats table | |
| INT alLinkStatsClear | 1.3.6.1.4.1.390.2.3.3 | INTEGER | read-write | When set, clears the link stats |
| INT alLinkStatsCollect | 1.3.6.1.4.1.390.2.3.2 | INTEGER | read-write | When set to enable(1), per link stats collection is enabled; when set to disable(0), the per link stats are not collected. |
| alLinkStatsTable | 1.3.6.1.4.1.390.2.3.4 | not-accessible | Per link stats table | |
| STR alMcpuPromVer | 1.3.6.1.4.1.390.2.1.3 | DisplayString | read-only | PROM software version of the motherboard CPU; it is an ASCII string that describes the version as well as the date and time the software was released from the factory. |
| STR alMcpuRtVer | 1.3.6.1.4.1.390.2.1.2 | DisplayString | read-only | Runtime software version of the motherboard CPU; it is an ASCII string that describes the version as well as the date and time the software was released from the factory. |
| almgmt | 1.3.6.1.4.1.390.2.3 | |||
| alPortConfigTable | 1.3.6.1.4.1.390.2.2.8 | not-accessible | Per port configuration for configuring Source and Destination Rules etc. | |
| alPortLinkTable | 1.3.6.1.4.1.390.2.3.6 | not-accessible | Per port link type | |
| INT alPortMonitorClose | 1.3.6.1.4.1.390.2.3.8 | INTEGER | read-write | Setting the value to close(1), will turn the port monitoring off. |
| alPortMonitorTable | 1.3.6.1.4.1.390.2.3.9 | not-accessible | ||
| alPortMonitorViewTable | 1.3.6.1.4.1.390.2.3.11 | not-accessible | ||
| alPortStateTable | 1.3.6.1.4.1.390.2.2.15 | not-accessible | Per port state information about spanning tree, dignostics and management. | |
| alPortStatsTable | 1.3.6.1.4.1.390.2.2.4 | not-accessible | Per port statistics | |
| alPortToPortTable | 1.3.6.1.4.1.390.2.2.7 | not-accessible | Statistics for port to port traffic. | |
| INT alPPDestinationPort | 1.3.6.1.4.1.390.2.2.7.1.2 | INTEGER | read-only | Source port number |
| INT alPPSourecPort | 1.3.6.1.4.1.390.2.2.7.1.1 | INTEGER | read-only | Source port number |
| alPSEntry | 1.3.6.1.4.1.390.1.3.1.4.1 | not-accessible | Information about a specific power supply. | |
| INT alPSNumber | 1.3.6.1.4.1.390.1.3.1.4.1.1 | INTEGER | read-only | The power supply number |
| INT alPSStatus | 1.3.6.1.4.1.390.1.3.1.4.1.2 | INTEGER | read-only | The status of the power supply identified by the instance of alPSNumber. |
| alPSTable | 1.3.6.1.4.1.390.1.3.1.4 | not-accessible | A table that contains information about each power supply in the PowerHub 7000 chassis. | |
| STR alRcpuOnePromVer | 1.3.6.1.4.1.390.2.1.10 | DisplayString | read-only | PROM software version of Ring CPU for the first FDDI board. |
| STR alRcpuOneRtVer | 1.3.6.1.4.1.390.2.1.8 | DisplayString | read-only | Runtime software version of Ring CPU for the first FDDI board. |
| STR alRcpuTwoPromVer | 1.3.6.1.4.1.390.2.1.11 | DisplayString | read-only | PROM software version of Ring CPU for the second FDDI board. |
| STR alRcpuTwoRtVer | 1.3.6.1.4.1.390.2.1.9 | DisplayString | read-only | Runtime software version of Ring CPU for the second FDDI board. |
| INT alReboot | 1.3.6.1.4.1.390.2.3.10 | INTEGER | read-write | Setting the value to Reboot(1), will reboot the PowerHub. |
| alrip | 1.3.6.1.4.1.390.2.4 | |||
| alRipAccptFilTable | 1.3.6.1.4.1.390.2.4.33 | not-accessible | RIP Accept filter table | |
| alRipConfigTable | 1.3.6.1.4.1.390.2.4.1 | not-accessible | Per port RIP configuration. | |
| INT alRipDynBadSrcIp | 1.3.6.1.4.1.390.2.4.29 | INTEGER | read-only | Packets with bad source IP address received. |
| INT alRipDynBadSrcPort | 1.3.6.1.4.1.390.2.4.28 | INTEGER | read-only | Packets with bad Source port received. |
| INT alRipDynBadVer | 1.3.6.1.4.1.390.2.4.26 | INTEGER | read-only | Bad version pkts received. |
| INT alRipDynBadZeroes | 1.3.6.1.4.1.390.2.4.27 | INTEGER | read-only | Bad zeroes received. |
| INT alRipDynFreeQueue | 1.3.6.1.4.1.390.2.4.32 | INTEGER | read-only | Free entries in the RIP processing queue. |
| INT alRipDynPktsQueued | 1.3.6.1.4.1.390.2.4.31 | INTEGER | read-only | Packets queued. |
| INT alRipDynPktsRcvd | 1.3.6.1.4.1.390.2.4.18 | INTEGER | read-only | Packets Received. |
| INT alRipDynPktsSelf | 1.3.6.1.4.1.390.2.4.30 | INTEGER | read-only | Packets from self received. |
| INT alRipDynPktsXmitted | 1.3.6.1.4.1.390.2.4.19 | INTEGER | read-only | Packets Sent. |
| INT alRipDynReqsRcvd | 1.3.6.1.4.1.390.2.4.20 | INTEGER | read-only | Requests Received. |
| INT alRipDynReqsXmitted | 1.3.6.1.4.1.390.2.4.22 | INTEGER | read-only | Requests Sent. |
| INT alRipDynRespRcvd | 1.3.6.1.4.1.390.2.4.21 | INTEGER | read-only | Responses Received. |
| INT alRipDynRespXmitted | 1.3.6.1.4.1.390.2.4.23 | INTEGER | read-only | Responses Sent. |
| INT alRipDynRouteTimeOuts | 1.3.6.1.4.1.390.2.4.24 | INTEGER | read-only | Route Timeouts. |
| INT alRipDynShortPkts | 1.3.6.1.4.1.390.2.4.25 | INTEGER | read-only | Short packets received. |
| alRipReportFilTable | 1.3.6.1.4.1.390.2.4.34 | not-accessible | RIP Report filter table | |
| INT alRipStatBadSrcIp | 1.3.6.1.4.1.390.2.4.14 | INTEGER | read-only | Packets with bad source IP address received. |
| INT alRipStatBadSrcPort | 1.3.6.1.4.1.390.2.4.13 | INTEGER | read-only | Packets with bad Source port received. |
| INT alRipStatBadVer | 1.3.6.1.4.1.390.2.4.11 | INTEGER | read-only | Bad version pkts received. |
| INT alRipStatBadZeroes | 1.3.6.1.4.1.390.2.4.12 | INTEGER | read-only | Bad zeroes received. |
| INT alRipStatFreeQueue | 1.3.6.1.4.1.390.2.4.17 | INTEGER | read-only | Free entries in the RIP processing queue. |
| INT alRipStatPktsQueued | 1.3.6.1.4.1.390.2.4.16 | INTEGER | read-only | Packets queued. |
| INT alRipStatPktsRcvd | 1.3.6.1.4.1.390.2.4.3 | INTEGER | read-only | Packets Received. |
| INT alRipStatPktsSelf | 1.3.6.1.4.1.390.2.4.15 | INTEGER | read-only | Packets from self received. |
| INT alRipStatPktsXmitted | 1.3.6.1.4.1.390.2.4.4 | INTEGER | read-only | Packets Sent. |
| INT alRipStatReqsRcvd | 1.3.6.1.4.1.390.2.4.5 | INTEGER | read-only | Requests Received. |
| INT alRipStatReqsXmitted | 1.3.6.1.4.1.390.2.4.7 | INTEGER | read-only | Requests Sent. |
| INT alRipStatRespRcvd | 1.3.6.1.4.1.390.2.4.6 | INTEGER | read-only | Responses Received. |
| INT alRipStatRespXmitted | 1.3.6.1.4.1.390.2.4.8 | INTEGER | read-only | Responses Sent. |
| INT alRipStatRouteTimeOuts | 1.3.6.1.4.1.390.2.4.9 | INTEGER | read-only | Route Timeouts. |
| INT alRipstatsClear | 1.3.6.1.4.1.390.2.4.2 | INTEGER | read-write | When set, clears the RIP stats |
| INT alRipStatShortPkts | 1.3.6.1.4.1.390.2.4.10 | INTEGER | read-only | Short packets received. |
| INT alSlotCardType | 1.3.6.1.4.1.390.1.3.1.1.1.2 | INTEGER | read-only | The card type for this slot. |
| STR alSlotDeviation | 1.3.6.1.4.1.390.1.3.1.1.1.7 | DisplayString | read-only | The deviation for this slot. |
| alSlotEntry | 1.3.6.1.4.1.390.1.3.1.1.1 | not-accessible | Information about a specific slot. | |
| STR alSlotIssue | 1.3.6.1.4.1.390.1.3.1.1.1.6 | DisplayString | read-only | The issue number for this slot. |
| STR alSlotModel | 1.3.6.1.4.1.390.1.3.1.1.1.4 | DisplayString | read-only | The model number for this card. |
| INT alSlotNumber | 1.3.6.1.4.1.390.1.3.1.1.1.1 | INTEGER | read-only | The slot number for which the following information applies. |
| INT alSlotPower12 | 1.3.6.1.4.1.390.1.3.1.1.1.10 | INTEGER | read-only | The number of milliamps. of current drawn by this slot at 12 Volts. |
| INT alSlotPower33 | 1.3.6.1.4.1.390.1.3.1.1.1.11 | INTEGER | read-only | The number of milliamps. of current drawn by this slot at 3.3 Volts. |
| INT alSlotPower5 | 1.3.6.1.4.1.390.1.3.1.1.1.9 | INTEGER | read-only | The number of milliamps. of current drawn by this slot at 5 Volts. |
| INT alSlotPowerOther | 1.3.6.1.4.1.390.1.3.1.1.1.12 | INTEGER | read-only | The number of milliamps. of current drawn by this slot at OTHER voltage. |
| STR alSlotRevision | 1.3.6.1.4.1.390.1.3.1.1.1.5 | DisplayString | read-only | The revision number for this card. |
| STR alSlotSerialNumber | 1.3.6.1.4.1.390.1.3.1.1.1.8 | DisplayString | read-only | The serial number of this card this slot. |
| INT alSlotStatus | 1.3.6.1.4.1.390.1.3.1.1.1.3 | INTEGER | read-only | The status of the card in this slot. |
| alSlotTable | 1.3.6.1.4.1.390.1.3.1.1 | not-accessible | A table that contains information about each slot in the PowerHub 7000 chassis. | |
| alSlotToVportTable | 1.3.6.1.4.1.390.1.3.1.3 | not-accessible | A table that contains information about each virtual port in the PowerHub 7000 chassis. | |
| INT alSlotVportControllerType | 1.3.6.1.4.1.390.1.3.1.3.1.6 | INTEGER | read-only | The controller type for the virtual port which is identified by the instance of alVportNumber. |
| alSlotVportEntry | 1.3.6.1.4.1.390.1.3.1.3.1 | not-accessible | Information about a specific virtual port. | |
| INT alSlotVportNumber | 1.3.6.1.4.1.390.1.3.1.3.1.3 | INTEGER | read-only | The virtual port number for which the following information applies. |
| INT alSlotVportPortNumber | 1.3.6.1.4.1.390.1.3.1.3.1.2 | INTEGER | read-only | The physical port number on the slot for a virtual port number which is identified by an instance of alVportNumber. |
| INT alSlotVportPortType | 1.3.6.1.4.1.390.1.3.1.3.1.4 | INTEGER | read-only | The port type for the virtual port which is identified by the instance of alVportNumber. |
| INT alSlotVportSlotNumber | 1.3.6.1.4.1.390.1.3.1.3.1.1 | INTEGER | read-only | The slot number for the virtual port number which is identified by the instance of alVportNumber. |
| INT alSlotVportStatus | 1.3.6.1.4.1.390.1.3.1.3.1.5 | INTEGER | read-only | The port status for the virtual port which is identified by the instance of alVportNumber. |
| alsnmp | 1.3.6.1.4.1.390.2.10 | |||
| alsystem | 1.3.6.1.4.1.390.2.1 | |||
| altcp | 1.3.6.1.4.1.390.2.5 | |||
| alTcpConnEntry | 1.3.6.1.4.1.390.2.5.6.1 | not-accessible | Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state. | |
| INT alTcpConnId | 1.3.6.1.4.1.390.2.5.6.1.1 | INTEGER | read-only | The connection Identifier by which a connection is addressed. |
| INT alTcpConnIdleTime | 1.3.6.1.4.1.390.2.5.1 | INTEGER | read-write | Time in minutes before sending keep-alives. The range is 5 to 30 minutes. |
| IP alTcpConnLocalAddress | 1.3.6.1.4.1.390.2.5.6.1.3 | IpAddress | read-only | The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used. |
| INT alTcpConnLocalPort | 1.3.6.1.4.1.390.2.5.6.1.4 | INTEGER | read-only | The local port number for this TCP connection. |
| IP alTcpConnRemAddress | 1.3.6.1.4.1.390.2.5.6.1.5 | IpAddress | read-only | The remote IP address for this TCP connection. |
| INT alTcpConnRemPort | 1.3.6.1.4.1.390.2.5.6.1.6 | INTEGER | read-only | The remote port number for this TCP connection. |
| INT alTcpConnState | 1.3.6.1.4.1.390.2.5.6.1.2 | INTEGER | read-write | The state of this TCP connection. The only value which may be set by a management station is deleteTCB(12). Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(12), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection. |
| alTcpConnTable | 1.3.6.1.4.1.390.2.5.6 | not-accessible | A table containing TCP connection-specific information. | |
| INT alTcpDisconnectInt | 1.3.6.1.4.1.390.2.5.3 | INTEGER | read-only | Time interval in seconds, before an idle connection is dropped. This equals to the sum of alTcpConnIdleTime plus eight times the alTcpKeepAliveInt interval. |
| alTcpFilTable | 1.3.6.1.4.1.390.2.5.7 | not-accessible | TCP filter table | |
| INT alTcpKeepAliveInt | 1.3.6.1.4.1.390.2.5.2 | INTEGER | read-write | Time interval in seconds between two successive keep-alive sends. The range is 30 to 240 seconds. |
| INT alTcpShortSegRcvd | 1.3.6.1.4.1.390.2.5.4 | INTEGER | read-only | Number of short segments received. |
| INT alTcpStatsClear | 1.3.6.1.4.1.390.2.5.5 | INTEGER | read-write | When set to 1, clears the TCP stats. |
| INT alVportControllerType | 1.3.6.1.4.1.390.1.3.1.2.1.6 | INTEGER | read-only | The controller type for the virtual port which is identified by the instance of alVportNumber. |
| alVportEntry | 1.3.6.1.4.1.390.1.3.1.2.1 | not-accessible | Information about a specific virtual port. | |
| INT alVportNumber | 1.3.6.1.4.1.390.1.3.1.2.1.1 | INTEGER | read-only | The virtual port number for which the following information applies. |
| INT alVportPortNumber | 1.3.6.1.4.1.390.1.3.1.2.1.3 | INTEGER | read-only | The physical port number on the slot for a virtual port number which is identified by an instance of alVportNumber. |
| INT alVportPortType | 1.3.6.1.4.1.390.1.3.1.2.1.4 | INTEGER | read-only | The port type for the virtual port which is identified by the instance of alVportNumber. |
| INT alVportSlotNumber | 1.3.6.1.4.1.390.1.3.1.2.1.2 | INTEGER | read-only | The slot number for the virtual port number which is identified by the instance of alVportNumber. |
| INT alVportStatus | 1.3.6.1.4.1.390.1.3.1.2.1.5 | INTEGER | read-only | The port status for the virtual port which is identified by the instance of alVportNumber. |
| alVportTable | 1.3.6.1.4.1.390.1.3.1.2 | not-accessible | A table that contains information about each virtual port in the PowerHub 7000 chassis. | |
| INT arpProxyEnable | 1.3.6.1.4.1.390.2.6.13.1.2 | INTEGER | read-write | If set to Enable(1), enables proxy arp for arp requests received on the port identified by the instance of arpProxyPort. If set to Disable(0), it disables the proxy arp for arp requests received on the ports identified by the instance of arpProxyPort. |
| arpProxyEntry | 1.3.6.1.4.1.390.2.6.13.1 | not-accessible | ||
| INT arpProxyPort | 1.3.6.1.4.1.390.2.6.13.1.1 | INTEGER | read-only | Port Number |
| OCT brGroupName | 1.3.6.1.4.1.390.2.2.13.1.3 | OCTET STRING | read-write | The name of the group for which this entry applies |
| INT brGroupNumber | 1.3.6.1.4.1.390.2.2.13.1.1 | INTEGER | read-write | The group number by which the group is identified with. |
| INT brGroupPortsMask | 1.3.6.1.4.1.390.2.2.13.1.2 | INTEGER | read-write | The ports associated with the group number identified by the instance of brGroupNumber. |
| brRuleEntry | 1.3.6.1.4.1.390.2.2.11.1 | not-accessible | ||
| INT brRuleNumber | 1.3.6.1.4.1.390.2.2.11.1.1 | INTEGER | read-write | The number of the rule with which it is identified. |
| STR brRuleStatement | 1.3.6.1.4.1.390.2.2.11.1.2 | DisplayString | read-write | Rule statement |
| PHY brRuleToNodeMacAddr | 1.3.6.1.4.1.390.2.2.12.1.2 | PhysAddress | read-write | The source MAC address |
| INT brRuleToNodePort | 1.3.6.1.4.1.390.2.2.12.1.1 | INTEGER | read-write | The number of the port for which this rule applies |
| INT brRuleToNodeRule | 1.3.6.1.4.1.390.2.2.12.1.3 | INTEGER | read-write | The rule number that applies to this entry. |
| CTR brTemplateComparator | 1.3.6.1.4.1.390.2.2.10.1.4 | Counter | read-write | |
| brTemplateEntry | 1.3.6.1.4.1.390.2.2.10.1 | not-accessible | ||
| CTR brTemplateMask | 1.3.6.1.4.1.390.2.2.10.1.3 | Counter | read-write | |
| INT brTemplateNumber | 1.3.6.1.4.1.390.2.2.10.1.1 | INTEGER | read-write | The number of the template with which it is identified. |
| INT brTemplateOffset | 1.3.6.1.4.1.390.2.2.10.1.2 | INTEGER | read-write | A displacement, in octets, from the beginning of the packet. This must be a multiple of 4 in the range from 0 to 124 decimal. A value of -1 will delete the entry |
| INT brTemplateOption | 1.3.6.1.4.1.390.2.2.10.1.5 | INTEGER | read-write | |
| common | 1.3.6.1.4.1.390.2 | |||
| INT fiberAuiStatus | 1.3.6.1.4.1.390.2.3.7.1.2 | INTEGER | read-only | The fiber aui status for the port that is specified by the instance of fiberStatsPort |
| INT fiberSecurityViolation | 1.3.6.1.4.1.390.2.3.7.1.3 | INTEGER | read-write | The fiber port for which the stats are requested or the Fiber violation is set |
| fiberStatsEntry | 1.3.6.1.4.1.390.2.3.7.1 | not-accessible | ||
| INT fiberStatsPort | 1.3.6.1.4.1.390.2.3.7.1.1 | INTEGER | read-only | The fiber port for which the stats are requested or the Fiber violation is set |
| INT ipAcsCtrlDelete | 1.3.6.1.4.1.390.2.6.16.1.2 | INTEGER | read-write | If set to 1, the entry is deleted. |
| INT ipAcsCtrlDstRule | 1.3.6.1.4.1.390.2.6.16.1.4 | INTEGER | read-write | Destination IP access filter rule |
| ipAcsCtrlEntry | 1.3.6.1.4.1.390.2.6.16.1 | not-accessible | ||
| INT ipAcsCtrlPort | 1.3.6.1.4.1.390.2.6.16.1.1 | INTEGER | read-write | Port number of the port for which the source and destination access filter apply. |
| INT ipAcsCtrlSrcRule | 1.3.6.1.4.1.390.2.6.16.1.3 | INTEGER | read-write | Source IP access filter rule |
| ipAcsCtrlTable | 1.3.6.1.4.1.390.2.6.16 | not-accessible | Per port IP access control filters | |
| INT ipFilDynStatsClear | 1.3.6.1.4.1.390.2.6.18.1.6 | INTEGER | read-write | Setting the value of 1, it will clear all the stats for the template identified by the instance of ipFilDynStatsTemplate. |
| ipFilDynStatsEntry | 1.3.6.1.4.1.390.2.6.18.1 | not-accessible | ||
| INT ipFilDynStatsInBytes | 1.3.6.1.4.1.390.2.6.18.1.3 | INTEGER | read-only | The number of bytes that matched the template identified by the instance of ipFilDynStatsTemplate. The template has to be a Source template. |
| INT ipFilDynStatsInPkts | 1.3.6.1.4.1.390.2.6.18.1.2 | INTEGER | read-only | The number of packets that matched the template identified by the instance of ipFilDynStatsTemplate. The template has to be a Source template. |
| INT ipFilDynStatsOutBytes | 1.3.6.1.4.1.390.2.6.18.1.5 | INTEGER | read-only | The number of bytes that matched the template identified by the instance of ipFilDynStatsTemplate. The template has to be a Destination template. |
| INT ipFilDynStatsOutPkts | 1.3.6.1.4.1.390.2.6.18.1.4 | INTEGER | read-only | The number of packets that matched the template identified by the instance of ipFilDynStatsTemplate. The template has to be a Destination template. |
| ipFilDynStatsTable | 1.3.6.1.4.1.390.2.6.18 | not-accessible | Per template dynamic statistics -- stats from the beginning of the last clear. | |
| INT ipFilDynStatsTemplate | 1.3.6.1.4.1.390.2.6.18.1.1 | INTEGER | read-only | The template number for which the stats are displayed |
| ipFilStatStatsEntry | 1.3.6.1.4.1.390.2.6.17.1 | not-accessible | ||
| INT ipFilStatStatsInBytes | 1.3.6.1.4.1.390.2.6.17.1.3 | INTEGER | read-only | The number of bytes that matched the template identified by the instance of ipFilStatStatsTemplate. The template has to be a Source template. |
| INT ipFilStatStatsInPkts | 1.3.6.1.4.1.390.2.6.17.1.2 | INTEGER | read-only | The number of packets that matched the template identified by the instance of ipFilStatStatsTemplate. The template has to be a Source template. |
| INT ipFilStatStatsOutBytes | 1.3.6.1.4.1.390.2.6.17.1.5 | INTEGER | read-only | The number of bytes that matched the template identified by the instance of ipFilStatStatsTemplate. The template has to be a Destination template. |
| INT ipFilStatStatsOutPkts | 1.3.6.1.4.1.390.2.6.17.1.4 | INTEGER | read-only | The number of packets that matched the template identified by the instance of ipFilStatStatsTemplate. The template has to be a Destination template. |
| ipFilStatStatsTable | 1.3.6.1.4.1.390.2.6.17 | not-accessible | Per template static statistics -- stats from the beginning of the last system reboot. | |
| INT ipFilStatStatsTemplate | 1.3.6.1.4.1.390.2.6.17.1.1 | INTEGER | read-only | The template number for which the stats are displayed |
| IP ipInterfaceAddress | 1.3.6.1.4.1.390.2.6.19.1.2 | IpAddress | read-write | |
| INT ipInterfaceBroadCast | 1.3.6.1.4.1.390.2.6.19.1.5 | INTEGER | read-write | |
| INT ipInterfaceCost | 1.3.6.1.4.1.390.2.6.19.1.7 | INTEGER | read-write | |
| INT ipInterfaceMtu | 1.3.6.1.4.1.390.2.6.19.1.4 | INTEGER | read-write | |
| INT ipInterfaceNumber | 1.3.6.1.4.1.390.2.6.19.1.1 | INTEGER | read-write | |
| INT ipInterfaceOctetsIn | 1.3.6.1.4.1.390.2.6.19.1.9 | INTEGER | read-only | |
| INT ipInterfaceOctetsOut | 1.3.6.1.4.1.390.2.6.19.1.11 | INTEGER | read-only | |
| INT ipInterfacePktsIn | 1.3.6.1.4.1.390.2.6.19.1.8 | INTEGER | read-only | |
| INT ipInterfacePktsOut | 1.3.6.1.4.1.390.2.6.19.1.10 | INTEGER | read-only | |
| INT ipInterfaceState | 1.3.6.1.4.1.390.2.6.19.1.6 | INTEGER | read-write | |
| IP ipInterfaceSubnetMask | 1.3.6.1.4.1.390.2.6.19.1.3 | IpAddress | read-write | |
| INT ipRtCacheClear | 1.3.6.1.4.1.390.2.6.20.1.3 | INTEGER | read-write | Setting this to Clear(1), will clear the routecache for the port and Destination address identified by the instance of ipRtCachePort and ipRtCacheDstAddress. |
| IP ipRtCacheDstAddress | 1.3.6.1.4.1.390.2.6.20.1.2 | IpAddress | read-write | |
| INT ipRtCachePort | 1.3.6.1.4.1.390.2.6.20.1.1 | INTEGER | read-write | |
| INT ipRuleDelete | 1.3.6.1.4.1.390.2.6.15.1.2 | INTEGER | read-write | If set to 1 the entry is deleted. |
| ipRuleEntry | 1.3.6.1.4.1.390.2.6.15.1 | not-accessible | ||
| INT ipRuleNumber | 1.3.6.1.4.1.390.2.6.15.1.1 | INTEGER | read-write | The number of the rule with which it is identified. |
| STR ipRuleTemplates | 1.3.6.1.4.1.390.2.6.15.1.3 | DisplayString | read-write | The templates associated with the rule identified by the instance of ipRuleNumber. |
| INT ipTemplateAction | 1.3.6.1.4.1.390.2.6.14.1.3 | INTEGER | read-write | Whether the packet being filtered should be forwarded or blocked |
| INT ipTemplateDelete | 1.3.6.1.4.1.390.2.6.14.1.2 | INTEGER | read-write | When set to Delete(1), this entry is deleted. |
| IP ipTemplateDstAddr | 1.3.6.1.4.1.390.2.6.14.1.6 | IpAddress | read-write | The portion of the packet's destination address specified by ipTemplateDstMask is matched with this address. |
| IP ipTemplateDstMask | 1.3.6.1.4.1.390.2.6.14.1.7 | IpAddress | read-write | Destination mask. The portion specified by this mask is matched with destination address. |
| INT ipTemplateDstPort | 1.3.6.1.4.1.390.2.6.14.1.10 | INTEGER | read-write | This is expressed as either a well-known protocol name or a well-known tcp or udp port number |
| ipTemplateEntry | 1.3.6.1.4.1.390.2.6.14.1 | not-accessible | ||
| INT ipTemplateNumber | 1.3.6.1.4.1.390.2.6.14.1.1 | INTEGER | read-write | The number of the template with which it is identified. |
| STR ipTemplateOperator | 1.3.6.1.4.1.390.2.6.14.1.9 | DisplayString | read-write | Allowed only if the protocol field is tcp or udp. |
| INT ipTemplateProtocol | 1.3.6.1.4.1.390.2.6.14.1.8 | INTEGER | read-write | Determines the type of packets that need to be filtered |
| IP ipTemplateSrcAddr | 1.3.6.1.4.1.390.2.6.14.1.4 | IpAddress | read-write | The portion of the packet's source address specified by ipTemplateSrcMask is matched with this address. |
| IP ipTemplateSrcMask | 1.3.6.1.4.1.390.2.6.14.1.5 | IpAddress | read-write | Source Mask. The portion specified by this mask is matched with source address. |
| INT linkControlEnable | 1.3.6.1.4.1.390.2.3.5.1.7 | INTEGER | read-write | Setting the value of this object to Enable (1), will enable the link and setting to Disable(2), will disable the link. |
| INT linkControlEnlState | 1.3.6.1.4.1.390.2.3.5.1.3 | INTEGER | read-only | Enable state for the link corresponds to enl option in lkd command. |
| linkControlEntry | 1.3.6.1.4.1.390.2.3.5.1 | not-accessible | ||
| INT linkControlLink | 1.3.6.1.4.1.390.2.3.5.1.2 | INTEGER | read-only | Link number for this entry. |
| INT linkControlLinkTest | 1.3.6.1.4.1.390.2.3.5.1.4 | INTEGER | read-only | Link test status for the link; corresponds to lt option of the lkd command. |
| INT linkControlPartition | 1.3.6.1.4.1.390.2.3.5.1.5 | INTEGER | read-only | Partitioning state of the link |
| INT linkControlPolarity | 1.3.6.1.4.1.390.2.3.5.1.6 | INTEGER | read-only | Polarity of the link |
| INT linkControlPort | 1.3.6.1.4.1.390.2.3.5.1.1 | INTEGER | read-only | Port number for this entry. |
| INT linkStatsBMCastPktsIn | 1.3.6.1.4.1.390.2.3.4.1.5 | INTEGER | read-only | Bmcast Pks In - corresponds to bpi |
| linkStatsEntry | 1.3.6.1.4.1.390.2.3.4.1 | not-accessible | ||
| INT linkStatsFCSErrs | 1.3.6.1.4.1.390.2.3.4.1.8 | INTEGER | read-only | FCS Errors corresponds to fcs |
| INT linkStatsFrameErrs | 1.3.6.1.4.1.390.2.3.4.1.7 | INTEGER | read-only | Frame Errors - corresponds to fa |
| INT linkStatsGiantPkts | 1.3.6.1.4.1.390.2.3.4.1.6 | INTEGER | read-only | Giant Pkts - corresponds to gp |
| INT linkStatsLink | 1.3.6.1.4.1.390.2.3.4.1.2 | INTEGER | read-only | Link Number |
| INT linkStatsOctetsIn | 1.3.6.1.4.1.390.2.3.4.1.4 | INTEGER | read-only | Octets In - corresponds to oi |
| INT linkStatsPktsIn | 1.3.6.1.4.1.390.2.3.4.1.3 | INTEGER | read-only | Pkts In - corresponds to pi |
| INT linkStatsPort | 1.3.6.1.4.1.390.2.3.4.1.1 | INTEGER | read-only | Port Number |
| INT linkStatsRcvCollisions | 1.3.6.1.4.1.390.2.3.4.1.9 | INTEGER | read-only | Receive Collisions- corresponds to rc |
| INT portConfigBlockLearnedEntries | 1.3.6.1.4.1.390.2.2.8.1.4 | INTEGER | read-write | When set to True (1), the port identified by the instance of portConfigPort will block the learned entries; if set to False (0) the port will not block the learned entries |
| INT portConfigDstRule | 1.3.6.1.4.1.390.2.2.8.1.3 | INTEGER | read-write | Destination Rule for the port number identified by the instance of portConfigPort |
| portConfigEntry | 1.3.6.1.4.1.390.2.2.8.1 | not-accessible | ||
| INT portConfigPort | 1.3.6.1.4.1.390.2.2.8.1.1 | INTEGER | read-only | The port number for this table entry |
| INT portConfigSrcRule | 1.3.6.1.4.1.390.2.2.8.1.2 | INTEGER | read-write | Source Rule for the port number identified by the instance of portConfigPort |
| portLinkEntry | 1.3.6.1.4.1.390.2.3.6.1 | not-accessible | ||
| INT portLinkPort | 1.3.6.1.4.1.390.2.3.6.1.1 | INTEGER | read-only | The port number for which the port type is to be set |
| INT portLinkType | 1.3.6.1.4.1.390.2.3.6.1.2 | INTEGER | read-write | The type of port |
| INT portMonDstPort | 1.3.6.1.4.1.390.2.3.9.1.2 | INTEGER | read-write | The traffic to/from portMonSrcPort will be monitored on this port |
| portMonitorEntry | 1.3.6.1.4.1.390.2.3.9.1 | not-accessible | ||
| portMonitorViewEntry | 1.3.6.1.4.1.390.2.3.11.1 | not-accessible | ||
| INT portMonSrcPort | 1.3.6.1.4.1.390.2.3.9.1.1 | INTEGER | read-write | The traffic to/from this port will be monitored on the portMonDstPort |
| INT portMonTrafficType | 1.3.6.1.4.1.390.2.3.9.1.3 | INTEGER | read-write | Setting this value to 1, will let the port monitor monitor forwarded traffic; setting to 0 means the forwarded traffic will not be monitored. |
| INT portMonViewDstPort | 1.3.6.1.4.1.390.2.3.11.1.2 | INTEGER | read-only | The traffic to this port from the port designated by portMonViewSrcPort will be monitored on portMonViewMonitorPort. |
| INT portMonViewMonitorPort | 1.3.6.1.4.1.390.2.3.11.1.3 | INTEGER | read-write | The traffic to portMonViewDstPort from the port designated by portMonViewSrcPort will be monitored on portMonViewMonitorPort. |
| INT portMonViewSrcPort | 1.3.6.1.4.1.390.2.3.11.1.1 | INTEGER | read-only | The traffic from this port to the port designated by portMonViewDstPort will be monitored on portMonViewMonitorPort. |
| INT portStateDiag | 1.3.6.1.4.1.390.2.2.15.1.2 | INTEGER | read-only | The diagnostics state of the port |
| portStateEntry | 1.3.6.1.4.1.390.2.2.15.1 | not-accessible | ||
| INT portStateMgmt | 1.3.6.1.4.1.390.2.2.15.1.3 | INTEGER | read-only | The management state of the port |
| INT portStatePort | 1.3.6.1.4.1.390.2.2.15.1.1 | INTEGER | read-only | The port number for this table entry |
| STR portStatePortName | 1.3.6.1.4.1.390.2.2.15.1.5 | DisplayString | read-only | The name of this port |
| INT portStateStp | 1.3.6.1.4.1.390.2.2.15.1.4 | INTEGER | read-only | The spanning tree state of the port. |
| INT portStatsCurrUtilization | 1.3.6.1.4.1.390.2.2.4.1.16 | INTEGER | read-only | |
| portStatsEntry | 1.3.6.1.4.1.390.2.2.4.1 | not-accessible | ||
| INT portStatsExcessRetries | 1.3.6.1.4.1.390.2.2.4.1.18 | INTEGER | read-only | |
| INT portStatsLossOfCarrier | 1.3.6.1.4.1.390.2.2.4.1.17 | INTEGER | read-only | |
| INT portStatsMultiCastPktsIn | 1.3.6.1.4.1.390.2.2.4.1.6 | INTEGER | read-only | |
| INT portStatsMulticastPktsOut | 1.3.6.1.4.1.390.2.2.4.1.7 | INTEGER | read-only | |
| INT portStatsOctetsIn | 1.3.6.1.4.1.390.2.2.4.1.4 | INTEGER | read-only | |
| INT portStatsOctetsOut | 1.3.6.1.4.1.390.2.2.4.1.5 | INTEGER | read-only | |
| INT portStatsPeakUtilization | 1.3.6.1.4.1.390.2.2.4.1.15 | INTEGER | read-only | |
| INT portStatsPktsIn | 1.3.6.1.4.1.390.2.2.4.1.2 | INTEGER | read-only | |
| INT portStatsPktsOut | 1.3.6.1.4.1.390.2.2.4.1.3 | INTEGER | read-only | |
| INT portStatsPort | 1.3.6.1.4.1.390.2.2.4.1.1 | INTEGER | read-only | |
| INT portStatsRcvBuffErrs | 1.3.6.1.4.1.390.2.2.4.1.9 | INTEGER | read-only | |
| INT portStatsRcvCollisions | 1.3.6.1.4.1.390.2.2.4.1.12 | INTEGER | read-only | |
| INT portStatsTableMisses | 1.3.6.1.4.1.390.2.2.4.1.8 | INTEGER | read-only | |
| INT portStatsTotalCollisions | 1.3.6.1.4.1.390.2.2.4.1.11 | INTEGER | read-only | |
| INT portStatsXmitBuffErrs | 1.3.6.1.4.1.390.2.2.4.1.10 | INTEGER | read-only | |
| INT portStatsXmitCollisions | 1.3.6.1.4.1.390.2.2.4.1.13 | INTEGER | read-only | |
| INT portStatsXmitQLen | 1.3.6.1.4.1.390.2.2.4.1.14 | INTEGER | read-only | |
| portToPortEntry | 1.3.6.1.4.1.390.2.2.7.1 | not-accessible | Statistics for port to port traffic | |
| INT portToPortOctets | 1.3.6.1.4.1.390.2.2.7.1.4 | INTEGER | read-only | |
| INT portToPortPackets | 1.3.6.1.4.1.390.2.2.7.1.3 | INTEGER | read-only | |
| powerbits | 1.3.6.1.4.1.390.1.2 | |||
| powerhub | 1.3.6.1.4.1.390.1.1 | |||
| powerhub7000 | 1.3.6.1.4.1.390.1.3 | |||
| products | 1.3.6.1.4.1.390.1 | |||
| IP ripAccptFilAddr | 1.3.6.1.4.1.390.2.4.33.1.2 | IpAddress | read-write | Valid network or subnet address |
| ripAccptFilEntry | 1.3.6.1.4.1.390.2.4.33.1 | not-accessible | RIP Accept filter entry | |
| IP ripAccptFilMask | 1.3.6.1.4.1.390.2.4.33.1.3 | IpAddress | read-write | Mask |
| INT ripAccptFilNumber | 1.3.6.1.4.1.390.2.4.33.1.1 | INTEGER | read-write | Filter Number; Range 1-64 |
| INT ripAccptFilPort | 1.3.6.1.4.1.390.2.4.33.1.4 | INTEGER | read-write | Port number on which network should be accepted or not. Range 1-14. CVG This range will change for PH2?? |
| INT ripConfigAccptDefaultRt | 1.3.6.1.4.1.390.2.4.1.1.7 | INTEGER | read-write | When RIP packets are received on the port, controls whether the hub accepts(learns) a default route that is reported in a RIP packet. |
| ripConfigEntry | 1.3.6.1.4.1.390.2.4.1.1 | not-accessible | ||
| INT ripConfigListen | 1.3.6.1.4.1.390.2.4.1.1.3 | INTEGER | read-write | Controls whether the hub processes RIP packets received on the port identified by the instance of ripConfigPort. |
| INT ripConfigPoison | 1.3.6.1.4.1.390.2.4.1.1.4 | INTEGER | read-write | Controls what happens when a route goes down. If set to no(0), the hub simply stops reporting the route. If set to yes(1), the hub reports it one more time, but with a metric value of 16, which infinity as far as RIP is concerned. Thus other routers learn immediately that the route is down. |
| INT ripConfigPort | 1.3.6.1.4.1.390.2.4.1.1.1 | INTEGER | read-write | Port number for which the RIP parameters are to be set or viewed. |
| INT ripConfigRptDefaultRt | 1.3.6.1.4.1.390.2.4.1.1.6 | INTEGER | read-write | When RIP packets are generated on the port, controls whether the hub reports the default routes, if any, in ints route table. |
| INT ripConfigRptStaticRt | 1.3.6.1.4.1.390.2.4.1.1.5 | INTEGER | read-write | When RIP packets are generated on the port, controls whether the hub reports the static routes in its route table. |
| INT ripConfigTalk | 1.3.6.1.4.1.390.2.4.1.1.2 | INTEGER | read-write | Controls whether the hub generates RIP packets on the port identified by the instance of ripConfigPort. |
| IP ripReportFilAddr | 1.3.6.1.4.1.390.2.4.34.1.2 | IpAddress | read-write | Valid network or subnet address |
| ripReportFilEntry | 1.3.6.1.4.1.390.2.4.34.1 | not-accessible | RIP Report filter entry | |
| IP ripReportFilMask | 1.3.6.1.4.1.390.2.4.34.1.3 | IpAddress | read-write | Mask |
| INT ripReportFilNumber | 1.3.6.1.4.1.390.2.4.34.1.1 | INTEGER | read-write | Filter Number; Range 1-64 |
| INT ripReportFilPort | 1.3.6.1.4.1.390.2.4.34.1.4 | INTEGER | read-write | Port number on which network should be reported or not. Port number range 1-14 CVG This range will probably change for PH2??. |
| INT tcpFilDstPort | 1.3.6.1.4.1.390.2.5.7.1.5 | INTEGER | read-write | smtp(1000), telnet(2000), ftp(3000) or valid port Number |
| tcpFilEntry | 1.3.6.1.4.1.390.2.5.7.1 | not-accessible | TCP filter entry | |
| INT tcpFilNumber | 1.3.6.1.4.1.390.2.5.7.1.1 | INTEGER | read-write | Filter Number; Range 1-32 |
| INT tcpFilProtocol | 1.3.6.1.4.1.390.2.5.7.1.4 | INTEGER | read-write | tcp(1) or udp(2) |
| IP tcpFilSrcAddr | 1.3.6.1.4.1.390.2.5.7.1.2 | IpAddress | read-write | Source address |
| IP tcpFilSrcMask | 1.3.6.1.4.1.390.2.5.7.1.3 | IpAddress | read-write | Mask |
RFC description
Proprietary MIB for Alantec PowerHub network bridge chassis, slots, and system components.
Start monitoring Alantec (Nortel) PowerHub 7000 fast Ethernet switch (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.