ACC-TSM

All MIBs › ACC-TSM

Category: Vendor: ACC/Ericsson

Description: Manages the Traffic Shaping Module on ACC/Ericsson routers, providing rate limiting and queue management for WAN interfaces.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ACC-TSM?

ACC-TSM is a vendor MIB from ACC (later part of Ericsson) for the Traffic Shaping Module, a WAN interface card function on ACC routers that enforces rate limiting and queue management for outbound traffic. With no module description or sample objects provided beyond a single group placeholder, its exposed data is presumed to center on configuration of shaping parameters (rate limits, queue depths) and related traffic statistics per shaped interface. Its practical value would be in monitoring the software/configuration status of the traffic-shaping feature — confirming shaping policies are applied and active, and tracking queue/drop counters that indicate congestion — though this cannot be fully confirmed given the minimal source data available. It likely depends on the ACC enterprise MIB tree for interface indexing, consistent with other ACC-prefixed router MIBs. It would typically be deployed on ACC/Ericsson WAN routers in service-provider or enterprise networks needing bandwidth shaping on wide-area links. Engineers can download the ACC-TSM file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ACC-TSM. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ACC/Ericsson WAN router

Monitoring Examples

An admin would look to accTsmGroup-scoped objects to check whether traffic shaping is enabled and to view rate-limit/queue configuration per interface, though no specific counter or table names are available in the source data to cite further. Given the sparse module description, this entry should be treated as a configuration-oriented shaping module rather than a rich, well-documented performance MIB.

What Can Be Monitored

traffic shaping policy status
configured rate limits
queue/drop counters

Imported Objects

From ACC-MIB

DisplayString
IfIndex
RowStatus
SmdsAddress
accBRG	OBJECT-IDENTITY

From ACC-SYSTEM

accTrapLogSeqNum

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
OBJECT-TYPE
TimeTicks

OIDs

OID symbolic	OID numeric	Type	Access	Description
accTsmGroup	1.3.6.1.4.1.5.1.1.56
accTsmTable	1.3.6.1.4.1.5.1.1.56.1		not-accessible	Table containing operational parameters of the TDM Bus.
accTsmTableEntry	1.3.6.1.4.1.5.1.1.56.1.1		not-accessible	An entry in the TSM table.
INT accTsmLdxIndex	1.3.6.1.4.1.5.1.1.56.1.1.1	INTEGER	read-only	The slot index of the current LDX from which the switching matrix is displayed.
INT accTsmMsgLevel	1.3.6.1.4.1.5.1.1.56.1.1.2	INTEGER	read-write	Message level for displaying TSM generated traps.
INT pysmiFakeCol715	1.3.6.1.4.1.5.1.1.56.1.1.4294967295	INTEGER	not-accessible
accTsmSwitchTable	1.3.6.1.4.1.5.1.1.56.2		not-accessible	Table containing switched parameters of the TDM Bus.
accTsmSwitchTableEntry	1.3.6.1.4.1.5.1.1.56.2.1		not-accessible	An entry in the TSM switching table.
INT accTsmSwitchingId	1.3.6.1.4.1.5.1.1.56.2.1.1	INTEGER	read-write	TSM assigned switching ID of this specific switching.
OCT accTsmLocStream	1.3.6.1.4.1.5.1.1.56.2.1.2	OCTET STRING	read-only	Local stream allocated for this switching setup.
OCT accTsmLocTimeslot	1.3.6.1.4.1.5.1.1.56.2.1.3	OCTET STRING	read-only	Local timeslot on the local stream allocated for this switching setup.
OCT accTsmTdmStream	1.3.6.1.4.1.5.1.1.56.2.1.4	OCTET STRING	read-only	TDM stream allocated for this switching setup.
OCT accTsmTdmTimeslot	1.3.6.1.4.1.5.1.1.56.2.1.5	OCTET STRING	read-only	Remote timeslot on the remote stream allocated for this switching setup.
INT accTsmSrcCkt	1.3.6.1.4.1.5.1.1.56.2.1.6	INTEGER	read-only	Source circuit.
INT accTsmDstCkt	1.3.6.1.4.1.5.1.1.56.2.1.7	INTEGER	read-only	Destination circuit.
INT pysmiFakeCol716	1.3.6.1.4.1.5.1.1.56.2.1.4294967295	INTEGER	not-accessible
INT accTsmTest	1.3.6.1.4.1.5.1.1.56.3	INTEGER	read-write	A Test objcet to setup test commands for internal use.
accSsuSrcTable	1.3.6.1.4.1.5.1.1.56.4		not-accessible	Table of potential serial synchronization unit clock sources. An entry exists for all potential clock sources.
accSsuSrcEntry	1.3.6.1.4.1.5.1.1.56.4.1		not-accessible	Configuration and status objects for a particular SSU source.
INT accSsuSrcType	1.3.6.1.4.1.5.1.1.56.4.1.1	INTEGER	read-only	The type of this clock source.
INT accSsuSrcIfIndex	1.3.6.1.4.1.5.1.1.56.4.1.2	INTEGER	read-only	The ifIndex of the clock source if its type is derived.
INT accSsuSrcPriority	1.3.6.1.4.1.5.1.1.56.4.1.3	INTEGER	read-write	The relative priority of this clock source.
INT accSsuSrcFrequency	1.3.6.1.4.1.5.1.1.56.4.1.4	INTEGER	read-write	The frequency in Khz of the clock source. This is settable only for the external source.
INT accSsuSrcRecovery	1.3.6.1.4.1.5.1.1.56.4.1.5	INTEGER	read-write	The recovery mechanism to use following source failure. This is only settable for the derived sources.
INT accSsuSrcThreshold	1.3.6.1.4.1.5.1.1.56.4.1.6	INTEGER	read-write	The numbers of failures permitted in an hour before a clock source whose recovery mechanism is automatic is disabled.
INT accSsuSrcState	1.3.6.1.4.1.5.1.1.56.4.1.7	INTEGER	read-only	The current state of this clock source.
CTR accSsuSrcFailures	1.3.6.1.4.1.5.1.1.56.4.1.8	Counter	read-only	The count of failures detected on this clock source.
accTsmDITable	1.3.6.1.4.1.5.1.1.56.5		not-accessible	Table containing Drop Insert objects.
accTsmDIEntry	1.3.6.1.4.1.5.1.1.56.5.1		not-accessible	An entry in the TSM Drop Insert table.
INT accTsmDIId	1.3.6.1.4.1.5.1.1.56.5.1.1	INTEGER	read-only	Internal identifier for the switched circuit.
INT accTsmDIFromDS0	1.3.6.1.4.1.5.1.1.56.5.1.2	INTEGER	read-only	Contains source timeslot.
INT accTsmDIFromDS1	1.3.6.1.4.1.5.1.1.56.5.1.3	INTEGER	read-only	Contains source DS1.
INT accTsmDIToDS0	1.3.6.1.4.1.5.1.1.56.5.1.4	INTEGER	read-only	Contains destination DS0.
INT accTsmDIToDS1	1.3.6.1.4.1.5.1.1.56.5.1.5	INTEGER	read-only	Contains destination DS1.
INT accTsmDIRowStatus	1.3.6.1.4.1.5.1.1.56.5.1.6	INTEGER	read-only	Contains validity of switching entry.
INT pysmiFakeCol717	1.3.6.1.4.1.5.1.1.56.5.1.4294967295	INTEGER	not-accessible

RFC description

Accellent TDM Switching Manager monitoring the TDM bus operational parameters and switching table functions.

Start monitoring ACC/Ericsson WAN access routers (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ACC-TSM

What Is ACC-TSM?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description