All MIBs › ASM-PRIVATE-COMMIB
Category: Vendor: ACC/Ericsson
Description: Defines private community string management objects for SNMP access control on ACC/Ericsson network devices.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ASM-PRIVATE-COMMIB?
ASM-PRIVATE-COMMIB is a vendor-specific MIB from ACC (a WAN/dial-access equipment maker later folded into Ericsson) that, based on its actual object definitions, provides storage-subsystem management for the device's internal diskette and hard-disk hardware, distinct from what its short description (community-string management) implies. It exposes tables describing diskette drives and hard-disk controllers, including drive type, controller slot number, and total counts of disks and controllers present in the chassis. This makes it a hardware-status monitoring MIB focused on local storage: administrators can check whether expected disk drives and controllers are present and correctly enumerated, which is useful for detecting a failed or missing storage component in the device (e.g., a boot/config-storage disk). As a self-contained vendor storage-inventory extension, it is not built on a broader IETF standard. It was deployed on ACC/Ericsson network access equipment (e.g., WAN access concentrators) that use internal diskette and hard-disk storage for configuration or firmware. Network engineers evaluating or troubleshooting this functionality can download the ASM-PRIVATE-COMMIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ASM-PRIVATE-COMMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Acer Incorporated / Fujitsu Siemens Computers ASM (Advanced Server Management) server hardware — storage, NIC, system board, and environment monitoring (legacy)
Monitoring Examples
An administrator would poll disketteDriveTable/disketteDriveEntry, indexed by disketteDrvIndex, to confirm disketteDrvType matches the expected floppy drive hardware, and check hdControllerTable/hdControllerEntry (via hdCntrlNum and hdCntrlSlotNum) alongside totalHdCntrlNum to verify all expected hard-disk controllers are recognized. A totalDiskNum or totalLDiskNum value lower than expected, or a missing hdControllerEntry for a known slot, would indicate a failed or disconnected disk controller in the chassis.
What Can Be Monitored
- diskette drive type/presence
- hard disk controller count and slot assignment
- total disk count
- total logical disk count
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| enterprises |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| acer | 1.3.6.1.4.1.1050 | |||
| asm | 1.3.6.1.4.1.1050.25 | |||
| NTF trapTemperatureWarning | 1.3.6.1.4.1.1050.25.0.1 | The agent will send a trap of this type when temperatures exceed the first level threshold value. | ||
| NTF trapTemperatureCritical | 1.3.6.1.4.1.1050.25.0.2 | The agent will send a trap of this type when temperatures exceed the second level threshold value. | ||
| NTF trapECC1BitError | 1.3.6.1.4.1.1050.25.0.3 | The agent will send a trap of this type when an ECC 1-bit error occurs. | ||
| NTF trapECCMBitError | 1.3.6.1.4.1.1050.25.0.4 | The agent will send a trap of this type when an ECC multiple-bit error occurs. | ||
| NTF trapFanStop | 1.3.6.1.4.1.1050.25.0.5 | The agent will send a trap of this type when any fan stops functioning. | ||
| NTF trapVoltage | 1.3.6.1.4.1.1050.25.0.6 | The agent will send a trap of this type when any voltage reading exceeds the safe operating range. | ||
| NTF trapCPUUtilization | 1.3.6.1.4.1.1050.25.0.7 | The agent will send a trap of this type when percent CPU utilization exceeds the threshold value. | ||
| NTF trapBusUtilization | 1.3.6.1.4.1.1050.25.0.8 | The agent will send a trap of this type when percent bus utilization exceeds the threshold value. | ||
| NTF trapMemoryUtilization | 1.3.6.1.4.1.1050.25.0.9 | The agent will send a trap of this type when percent memory utilization exceeds the threshold value. | ||
| NTF trapVolumeUtilization | 1.3.6.1.4.1.1050.25.0.10 | The agent will send a trap of this type when percent volume utilization exceeds the threshold value. | ||
| NTF trapNICCounter | 1.3.6.1.4.1.1050.25.0.11 | The agent will send a trap of this type when any NIC statistical counter exceeds the threshold value. | ||
| NTF trapPSFail | 1.3.6.1.4.1.1050.25.0.12 | The agent will send a trap of this type when any power supply fails. | ||
| NTF trapACFail | 1.3.6.1.4.1.1050.25.0.13 | The agent will send a trap of this type when AC power fails. | ||
| NTF trapPowerFanFail | 1.3.6.1.4.1.1050.25.0.14 | The agent will send a trap of this type when any power sub-system fan fails. | ||
| NTF trapBatteryFail | 1.3.6.1.4.1.1050.25.0.15 | The agent will send a trap of this type when UPS battery fails. | ||
| NTF trapChassisIntrusion | 1.3.6.1.4.1.1050.25.0.16 | The agent will send a trap of this type when chassis intrusion occurs. | ||
| NTF trapFuseFail | 1.3.6.1.4.1.1050.25.0.17 | The agent will send a trap of this type when fuse failed. | ||
| NTF trapRPSFail | 1.3.6.1.4.1.1050.25.0.18 | The agent will send a trap of this type when redundant power supply is failed. | ||
| NTF trapRPSFanFail | 1.3.6.1.4.1.1050.25.0.19 | The agent will send a trap of this type when redundant power supply fan is failed. | ||
| NTF trapBiosEventLog | 1.3.6.1.4.1.1050.25.0.20 | The agent will send a trap of this type when bios has new eventlog. | ||
| NTF trapBiosEventLogUtilization | 1.3.6.1.4.1.1050.25.0.21 | The agent will send a trap of this type when bios eventlog utilization exceeds threshold. | ||
| NTF trapCPUAbnormal | 1.3.6.1.4.1.1050.25.0.22 | The agent will send a trap of this type when CPU has internal error. | ||
| NTF trapAssetChange | 1.3.6.1.4.1.1050.25.0.23 | The agent will send a trap of this type when asset is changed. | ||
| storage | 1.3.6.1.4.1.1050.25.1 | |||
| disketteDriveTable | 1.3.6.1.4.1.1050.25.1.1 | not-accessible | This entry is a table containing information about all diskette drives. | |
| disketteDriveEntry | 1.3.6.1.4.1.1050.25.1.1.1 | not-accessible | This entry contains information about each diskette drive. | |
| DIS disketteDrvIndex | 1.3.6.1.4.1.1050.25.1.1.1.1 | DisketteDrvIndex | read-only | This entry displays the diskette drive table index. |
| INT disketteDrvType | 1.3.6.1.4.1.1050.25.1.1.1.2 | INTEGER | read-only | This entry displays the diskette drive type: 0 = Not present 1 = 360K 5.25inch 2 = 1.2M 5.25inch 3 = 720K 3.5inch 4 = 1.44M 3.5inch 5 = 2.88M 3.5inch |
| INT totalHdCntrlNum | 1.3.6.1.4.1.1050.25.1.2 | INTEGER | read-only | This entry displays the total number of hard disk controllers (HDC). |
| hdControllerTable | 1.3.6.1.4.1.1050.25.1.3 | not-accessible | This entry is a table containing information about all HDCs. | |
| hdControllerEntry | 1.3.6.1.4.1.1050.25.1.3.1 | not-accessible | This entry contains information about each HDC. | |
| INT hdCntrlNum | 1.3.6.1.4.1.1050.25.1.3.1.1 | INTEGER | read-only | This entry is an index to the HDC table starting at zero (0). |
| INT hdCntrlSlotNum | 1.3.6.1.4.1.1050.25.1.3.1.2 | INTEGER | read-only | This entry shows the slot number occupied by the controller. |
| INT hdCntrlType | 1.3.6.1.4.1.1050.25.1.3.1.4 | INTEGER | read-only | This entry shows the HDC type: 0 = Unknown 1 = SCSI 2 = IDE |
| INT hdCntrlIoPort | 1.3.6.1.4.1.1050.25.1.3.1.6 | INTEGER | read-only | This entry shows the I/O port address occupied by the HDC. |
| INT hdCntrlIntr | 1.3.6.1.4.1.1050.25.1.3.1.7 | INTEGER | read-only | This entry shows the interrupt number occupied by the HDC. |
| INT hdCntrlDMA | 1.3.6.1.4.1.1050.25.1.3.1.9 | INTEGER | read-only | This entry shows the DMA channel occupied by the HDC. |
| STR hdCntrlModel | 1.3.6.1.4.1.1050.25.1.3.1.11 | DisplayString | read-only | This entry shows the HDC model name. |
| INT totalDiskNum | 1.3.6.1.4.1.1050.25.1.4 | INTEGER | read-only | This entry displays the number of hard disks installed. |
| diskTable | 1.3.6.1.4.1.1050.25.1.5 | not-accessible | This entry is a table containing information about all hard disks installed. | |
| diskEntry | 1.3.6.1.4.1.1050.25.1.5.1 | not-accessible | This entry contains information about each disk drive installed. | |
| INT diskNum | 1.3.6.1.4.1.1050.25.1.5.1.1 | INTEGER | read-only | This entry is an index to the disk table starting at zero (0). |
| INT diskHdCntrlNum | 1.3.6.1.4.1.1050.25.1.5.1.2 | INTEGER | read-only | This entry shows the HDC number (refer to hdCntrlNum) to which the disk is connected. |
| INT diskHdCntrlSlotNum | 1.3.6.1.4.1.1050.25.1.5.1.3 | INTEGER | read-only | This entry shows the slot number of the HDC (refer to hdCntrlSlotNum) to which the disk is connected. |
| INT diskId | 1.3.6.1.4.1.1050.25.1.5.1.5 | INTEGER | read-only | This entry displays disk IDs depending on each disk type. For example, with a SCSI disk installed, the value for this entry will represent a SCSI ID. IDE disks have two values: 0 refers to a master drive while 1 refers to a slave drive. |
| INT diskSize | 1.3.6.1.4.1.1050.25.1.5.1.7 | INTEGER | read-only | This entry shows the physical disk size in KB. |
| STR diskModel | 1.3.6.1.4.1.1050.25.1.5.1.8 | DisplayString | read-only | This entry shows the disk model. |
| OCT diskType | 1.3.6.1.4.1.1050.25.1.5.1.10 | OCTET STRING | read-only | This entry shows the disk type, i.e. SCSI, IDE or N/A. |
| INT diskBusyRatio | 1.3.6.1.4.1.1050.25.1.5.1.12 | INTEGER | read-only | This entry shows the Disk Busy ratio (%). |
| INT averageDiskReadWriteTime | 1.3.6.1.4.1.1050.25.1.5.1.13 | INTEGER | read-only | This entry shows the disk's average read/write time. |
| INT numberOfDiskTransfer | 1.3.6.1.4.1.1050.25.1.5.1.14 | INTEGER | read-only | This entry shows the number of disk transfers. |
| INT byteOfDiskTransfer | 1.3.6.1.4.1.1050.25.1.5.1.15 | INTEGER | read-only | This entry shows the total size of all disk transfers in bytes. |
| INT deviceType | 1.3.6.1.4.1.1050.25.1.5.1.16 | INTEGER | read-only | This entry shows the device type. 0 : Unknown device 1 : Hard disk 2 : CD-ROM drive 3 : Tape drive |
| nic | 1.3.6.1.4.1.1050.25.2 | |||
| INT totalNicCntrlNum | 1.3.6.1.4.1.1050.25.2.1 | INTEGER | read-only | This entry displays the number of network interface controllers (NIC) installed. |
| nicControllerTable | 1.3.6.1.4.1.1050.25.2.2 | not-accessible | This entry is a table containing information about all NICs installed. | |
| nicControllerEntry | 1.3.6.1.4.1.1050.25.2.2.1 | not-accessible | This entry contains generic information about each NIC. | |
| INT nicCntrlNum | 1.3.6.1.4.1.1050.25.2.2.1.1 | INTEGER | read-only | This entry is an index of the NIC table starting at 0. |
| INT nicCntrlSlotNum | 1.3.6.1.4.1.1050.25.2.2.1.2 | INTEGER | read-only | This entry shows the slot number occupied by the NIC. |
| INT nicCntrlIoPort | 1.3.6.1.4.1.1050.25.2.2.1.3 | INTEGER | read-only | This entry shows the IO port occupied by the NIC. |
| INT nicCntrlDMA | 1.3.6.1.4.1.1050.25.2.2.1.4 | INTEGER | read-only | This entry shows the DMA channel occupied by the NIC. |
| INT nicCntrlIntr | 1.3.6.1.4.1.1050.25.2.2.1.5 | INTEGER | read-only | This entry shows the interrupt number occupied by the NIC. |
| INT nicCntrlSharedMem | 1.3.6.1.4.1.1050.25.2.2.1.6 | INTEGER | read-only | This entry shows the shared memory address used by the NIC. |
| STR nicCntrlModel | 1.3.6.1.4.1.1050.25.2.2.1.8 | DisplayString | read-only | This entry shows the NIC model. |
| STR nicCntrlType | 1.3.6.1.4.1.1050.25.2.2.1.10 | DisplayString | read-only | This entry shows the NIC type information such as Ethernet or Token Ring. |
| STR nicMACAddress | 1.3.6.1.4.1.1050.25.2.2.1.11 | DisplayString | read-only | This entry shows the NIC hardware's six-byte address. |
| INT nicMediaType | 1.3.6.1.4.1.1050.25.2.2.1.12 | INTEGER | read-only | This entry shows the NIC media type information: 1=Ethernet 2=Token-Ring |
| INT nicInterfaceSpeed | 1.3.6.1.4.1.1050.25.2.2.1.13 | INTEGER | read-only | This entry shows the NIC interface speed information in byte/sec |
| nwNic | 1.3.6.1.4.1.1050.25.2.3 | |||
| nwNicGenericCounterTable | 1.3.6.1.4.1.1050.25.2.3.1 | not-accessible | This entry is a table containing information about all groups of NetWare NIC generic counters. | |
| nwNicGenericCounter | 1.3.6.1.4.1.1050.25.2.3.1.1 | not-accessible | This entry contains information about each group of NetWare NIC generic counters. | |
| GAU nwNicNumRcvPkts | 1.3.6.1.4.1.1050.25.2.3.1.1.1 | Gauge | read-only | This entry shows the number of received packets by the LAN card. |
| GAU nwNicNumRcvBytes | 1.3.6.1.4.1.1050.25.2.3.1.1.2 | Gauge | read-only | This entry shows the number of received bytes by the LAN card. |
| GAU nwNicNumSndPkts | 1.3.6.1.4.1.1050.25.2.3.1.1.3 | Gauge | read-only | This entry shows the number of sent packets from the LAN card. |
| GAU nwNicNumSndBytes | 1.3.6.1.4.1.1050.25.2.3.1.1.4 | Gauge | read-only | This entry shows the number of sent bytes from the LAN card. |
| CTR nwNicNoEcbCount | 1.3.6.1.4.1.1050.25.2.3.1.1.5 | Counter | read-only | This entry shows the No ECB Available Count. |
| CTR nwNicSndTooBigCnt | 1.3.6.1.4.1.1050.25.2.3.1.1.6 | Counter | read-only | This entry shows the Send Packet Too Big Count. |
| CTR nwNicRcvPktOvlCnt | 1.3.6.1.4.1.1050.25.2.3.1.1.7 | Counter | read-only | This entry shows the Receive Packet Overflow Count. |
| CTR nwNicRcvPktTooBigCnt | 1.3.6.1.4.1.1050.25.2.3.1.1.8 | Counter | read-only | This entry shows the Receive Packet Too Big Count. |
| CTR nwNicRcvPktTooSmallCnt | 1.3.6.1.4.1.1050.25.2.3.1.1.9 | Counter | read-only | This entry shows the Receive Packet Too Small Count. |
| CTR nwNicRcvPktMiscErr | 1.3.6.1.4.1.1050.25.2.3.1.1.10 | Counter | read-only | This entry shows the Receive Packet Miscellaneous Errors. |
| CTR nwNicSndPktMiscErr | 1.3.6.1.4.1.1050.25.2.3.1.1.11 | Counter | read-only | This entry shows the Send Packet Miscellaneous Errors. |
| CTR nwNicSndPktRetryCnt | 1.3.6.1.4.1.1050.25.2.3.1.1.12 | Counter | read-only | This entry shows the Send Packet Retry Count. |
| CTR nwNicChkSumErr | 1.3.6.1.4.1.1050.25.2.3.1.1.13 | Counter | read-only | This entry shows the Checksum Errors. |
| CTR nwNicRcvMismatchCnt | 1.3.6.1.4.1.1050.25.2.3.1.1.14 | Counter | read-only | This entry shows the Hardware Receive Mismatch Count. |
| CTR nwNicAdapterRstCnt | 1.3.6.1.4.1.1050.25.2.3.1.1.15 | Counter | read-only | This entry shows the Adapter Reset Count. |
| nwNicGenericThresholdTable | 1.3.6.1.4.1.1050.25.2.3.2 | not-accessible | This entry is a table containing information about all groups of thresholds for NetWare NIC generic counters. | |
| nwNicGenericThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1 | not-accessible | This entry contains information about each group of thresholds for NetWare NIC generic counters. | |
| INT nwNicNumRcvPktsThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.1 | INTEGER | read-write | This entry shows the threshold setting of received packets by the LAN card. |
| INT nwNicNumRcvBytesThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.2 | INTEGER | read-write | This entry shows the threshold setting of received bytes by the LAN card. |
| INT nwNicNumSndPktsThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.3 | INTEGER | read-write | This entry shows the threshold setting of sent packets from the LAN card. |
| INT nwNicNumSndBytesThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.4 | INTEGER | read-write | This entry shows the threshold setting of sent bytes from the LAN card. |
| INT nwNicNoEcbCountThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.5 | INTEGER | read-write | This entry shows the threshold setting of No ECB Available Count. |
| INT nwNicSndTooBigCntThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.6 | INTEGER | read-write | This entry shows the threshold setting of Send Packet Too Big Count. |
| INT nwNicRcvPktOvlCntThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.7 | INTEGER | read-write | This entry shows the threshold setting of Receive Packet Overflow Count. |
| INT nwNicRcvPktTooBigCntThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.8 | INTEGER | read-write | This entry shows the threshold setting of Receive Packet Too Big Count. |
| INT nwNicRcvPktTooSmallCntThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.9 | INTEGER | read-write | This entry shows the threshold setting of Receive Packet Too Small Count. |
| INT nwNicRcvPktMiscErrThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.10 | INTEGER | read-write | This entry shows the threshold setting of Receive Packet Miscellaneous Errors. |
| INT nwNicSndPktMiscErrThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.11 | INTEGER | read-write | This entry shows the threshold setting of Send Packet Miscellaneous Errors. |
| INT nwNicSndPktRetryCntThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.12 | INTEGER | read-write | This entry shows the threshold setting of Send Packet Retry Count. |
| INT nwNicChkSumErrThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.13 | INTEGER | read-write | This entry shows the threshold setting of Checksum Errors. |
| INT nwNicRcvMismatchCntThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.14 | INTEGER | read-write | This entry shows the threshold setting of Hardware Receive Mismatch Count. |
| INT nwNicAdapterRstCntThreshold | 1.3.6.1.4.1.1050.25.2.3.2.1.15 | INTEGER | read-write | This entry shows the threshold setting of Adapter Reset Count. |
| nwNicEthernetCounterTable | 1.3.6.1.4.1.1050.25.2.3.3 | not-accessible | This entry is a table containing information about all groups of NetWare NIC Ethernet counters. | |
| nwNicEthernetCounter | 1.3.6.1.4.1.1050.25.2.3.3.1 | not-accessible | This entry contains information about each group of NetWare NIC Ethernet counters. | |
| CTR nwNicSndOkSingleColliCnt | 1.3.6.1.4.1.1050.25.2.3.3.1.1 | Counter | read-only | This entry shows the Send OK Single Collision Count. |
| CTR nwNicSndOkMultipleColliCnt | 1.3.6.1.4.1.1050.25.2.3.3.1.2 | Counter | read-only | This entry shows the Send OK Multiple Collision Count. |
| CTR nwNicSndOkButDeferred | 1.3.6.1.4.1.1050.25.2.3.3.1.3 | Counter | read-only | This entry shows the Send OK But Deferred. |
| CTR nwNicSndAbortLateColli | 1.3.6.1.4.1.1050.25.2.3.3.1.4 | Counter | read-only | This entry shows the Send Abort From Late Collision. |
| CTR nwNicSndAbortExcessColli | 1.3.6.1.4.1.1050.25.2.3.3.1.5 | Counter | read-only | This entry shows the Send Abort From Excess Collisions. |
| CTR nwNicSndAbortCarrierSense | 1.3.6.1.4.1.1050.25.2.3.3.1.6 | Counter | read-only | This entry shows the Send Abort From Carrier Sense. |
| CTR nwNicSndAbortExcessDefer | 1.3.6.1.4.1.1050.25.2.3.3.1.7 | Counter | read-only | This entry shows the Send Abort From Excessive Deferral. |
| CTR nwNicRcvAbortFrameAlignment | 1.3.6.1.4.1.1050.25.2.3.3.1.8 | Counter | read-only | This entry shows the Receive Abort From Bad Frame Alignment. |
| nwNicEthernetThresholdTable | 1.3.6.1.4.1.1050.25.2.3.4 | not-accessible | This entry is a table containing information about all groups of thresholds for NetWare NIC Ethernet counters. | |
| nwNicEthernetThreshold | 1.3.6.1.4.1.1050.25.2.3.4.1 | not-accessible | This entry contains information about each group of thresholds for NetWare NIC Ethernet counters. | |
| INT nwNicSndOkSingleColliCntThreshold | 1.3.6.1.4.1.1050.25.2.3.4.1.1 | INTEGER | read-write | This entry shows the threshold setting of Send OK Single Collision Count. |
| INT nwNicSndOkMultipleColliCntThreshold | 1.3.6.1.4.1.1050.25.2.3.4.1.2 | INTEGER | read-write | This entry shows the threshold setting of Send OK Multiple Collision Count. |
| INT nwNicSndOkButDeferredThreshold | 1.3.6.1.4.1.1050.25.2.3.4.1.3 | INTEGER | read-write | This entry shows the threshold setting of Send OK But Deferred. |
| INT nwNicSndAbortLateColliThreshold | 1.3.6.1.4.1.1050.25.2.3.4.1.4 | INTEGER | read-write | This entry shows the threshold setting of Send Abort From Late Collision. |
| INT nwNicSndAbortExcessColliThreshold | 1.3.6.1.4.1.1050.25.2.3.4.1.5 | INTEGER | read-write | This entry shows the threshold setting of Send Abort From Excess Collisions. |
| INT nwNicSndAbortCarrierSenseThreshold | 1.3.6.1.4.1.1050.25.2.3.4.1.6 | INTEGER | read-write | This entry shows the threshold setting of Send Abort From Carrier Sense. |
| INT nwNicSndAbortExcessDeferThreshold | 1.3.6.1.4.1.1050.25.2.3.4.1.7 | INTEGER | read-write | This entry shows the threshold setting of Send Abort From Excessive Deferral. |
| INT nwNicRcvAbortFrameAlignmentThreshold | 1.3.6.1.4.1.1050.25.2.3.4.1.8 | INTEGER | read-write | This entry shows the threshold setting of Receive Abort From Bad Frame Alignment. |
| nwNicTokenRingCounterTable | 1.3.6.1.4.1.1050.25.2.3.5 | not-accessible | This entry is a table containing information about all groups of NetWare NIC Token Ring counters. | |
| nwNicTokenRingCounter | 1.3.6.1.4.1.1050.25.2.3.5.1 | not-accessible | This entry contains information about each group of NetWare NIC Token Ring counters. | |
| CTR nwNicACErrorCounter | 1.3.6.1.4.1.1050.25.2.3.5.1.1 | Counter | read-only | This entry shows the ACErrorCounter. |
| CTR nwNicAbortDelimiterCounter | 1.3.6.1.4.1.1050.25.2.3.5.1.2 | Counter | read-only | This entry shows the AbortDelimiterCounter. |
| CTR nwNicBurstErrorCounter | 1.3.6.1.4.1.1050.25.2.3.5.1.3 | Counter | read-only | This entry shows the BurstErrorCounter. |
| CTR nwNicFrameCopiedErrorCounter | 1.3.6.1.4.1.1050.25.2.3.5.1.4 | Counter | read-only | This entry shows the FrameCopiedErrorCounter. |
| CTR nwNicFrequencyErrorCounter | 1.3.6.1.4.1.1050.25.2.3.5.1.5 | Counter | read-only | This entry shows the FrequencyErrorCounter. |
| CTR nwNicInternalErrorCounter | 1.3.6.1.4.1.1050.25.2.3.5.1.6 | Counter | read-only | This entry shows the InternalErrorCounter. |
| CTR nwNicLastRingStatus | 1.3.6.1.4.1.1050.25.2.3.5.1.7 | Counter | read-only | This entry shows the LastRingStatus. |
| CTR nwNicLineErrorCounter | 1.3.6.1.4.1.1050.25.2.3.5.1.8 | Counter | read-only | This entry shows the LineErrorCounter. |
| CTR nwNicLostFrameCounter | 1.3.6.1.4.1.1050.25.2.3.5.1.9 | Counter | read-only | This entry shows the LostFrameCounter. |
| CTR nwNicTokenErrorCounter | 1.3.6.1.4.1.1050.25.2.3.5.1.10 | Counter | read-only | This entry shows the TokenErrorCounter. |
| nwNicTokenRingThresholdTable | 1.3.6.1.4.1.1050.25.2.3.6 | not-accessible | This entry is a table containing information about all groups of thresholds for NetWare NIC Token Ring counters. | |
| nwNicTokenRingThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1 | not-accessible | This entry contains information about each group of thresholds for NetWare NIC Token Ring counters. | |
| INT nwNicACErrorCounterThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1.1 | INTEGER | read-write | This entry shows the threshold setting of ACErrorCounter. |
| INT nwNicAbortDelimiterCounterThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1.2 | INTEGER | read-write | This entry shows the threshold setting of AbortDelimiterCounter. |
| INT nwNicBurstErrorCounterThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1.3 | INTEGER | read-write | This entry shows the threshold setting of BurstErrorCounter. |
| INT nwNicFrameCopiedErrorCounterThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1.4 | INTEGER | read-write | This entry shows the threshold setting of FrameCopiedErrorCounter. |
| INT nwNicFrequencyErrorCounterThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1.5 | INTEGER | read-write | This entry shows the threshold setting of FrequencyErrorCounter. |
| INT nwNicInternalErrorCounterThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1.6 | INTEGER | read-write | This entry shows the threshold setting of InternalErrorCounter. |
| INT nwNicLastRingStatusThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1.7 | INTEGER | read-write | This entry shows the threshold setting of LastRingStatus. |
| INT nwNicLineErrorCounterThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1.8 | INTEGER | read-write | This entry shows the threshold setting of LineErrorCounter. |
| INT nwNicLostFrameCounterThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1.9 | INTEGER | read-write | This entry shows the threshold setting of LostFrameCounter. |
| INT nwNicTokenErrorCounterThreshold | 1.3.6.1.4.1.1050.25.2.3.6.1.10 | INTEGER | read-write | This entry shows the threshold setting of TokenErrorCounter. |
| scoNic | 1.3.6.1.4.1.1050.25.2.4 | |||
| scoNicGenericCounterTable | 1.3.6.1.4.1.1050.25.2.4.1 | not-accessible | This entry is a table of SCO NIC generic counters. | |
| scoNicGenericCounter | 1.3.6.1.4.1.1050.25.2.4.1.1 | not-accessible | This entry contains information about each SCO NIC generic counter. | |
| GAU scoNicNumRcvPkts | 1.3.6.1.4.1.1050.25.2.4.1.1.1 | Gauge | read-only | This entry is the current number of received packets in this NIC card. |
| GAU scoNicNumRcvBytes | 1.3.6.1.4.1.1050.25.2.4.1.1.2 | Gauge | read-only | This entry is the current number of received bytes in this NIC card. |
| GAU scoNicNumSndPkts | 1.3.6.1.4.1.1050.25.2.4.1.1.3 | Gauge | read-only | This entry is the current number of sent packets in this NIC card. |
| GAU scoNicNumSndBytes | 1.3.6.1.4.1.1050.25.2.4.1.1.4 | Gauge | read-only | This entry is the current number of sent bytes in this NIC card. |
| CTR scoNicFrameDef | 1.3.6.1.4.1.1050.25.2.4.1.1.5 | Counter | read-only | This entry is a variable that registers the number of frames deferred due to data link traffic. |
| CTR scoNicCollisions | 1.3.6.1.4.1.1050.25.2.4.1.1.6 | Counter | read-only | This entry is a variable that registers the number of total collisions in transmitted frames. |
| CTR scoNicFrameColl | 1.3.6.1.4.1.1050.25.2.4.1.1.7 | Counter | read-only | This entry is a variable that registers the total collisions that occurred when a frame was being transmitted. |
| CTR scoNicOFrameColl | 1.3.6.1.4.1.1050.25.2.4.1.1.8 | Counter | read-only | This entry is a variable that registers the number of collisions that occurred when a frame was not being transmitted (out-of-frame collisions). |
| CTR scoNicXsColl | 1.3.6.1.4.1.1050.25.2.4.1.1.9 | Counter | read-only | This entry is a variable that registers the number of frames dropped due to excessive collisions. |
| CTR scoNicFrameNosr | 1.3.6.1.4.1.1050.25.2.4.1.1.10 | Counter | read-only | This entry is a variable that registers the number of frames dropped due to allocb failure. |
| CTR scoNicNoResource | 1.3.6.1.4.1.1050.25.2.4.1.1.11 | Counter | read-only | This entry is the number of frames dropped due to no resource. |
| CTR scoNicBadSum | 1.3.6.1.4.1.1050.25.2.4.1.1.12 | Counter | read-only | This entry is a variable that registers the number of received frames with a bad checksum. |
| CTR scoNicAlign | 1.3.6.1.4.1.1050.25.2.4.1.1.13 | Counter | read-only | This entry is a variable that registers the number of received frames with alignment errors. |
| CTR scoNicBadLen | 1.3.6.1.4.1.1050.25.2.4.1.1.14 | Counter | read-only | This entry is a variable that registers the number of received frames with a bad length. |
| CTR scoNicBadSap | 1.3.6.1.4.1.1050.25.2.4.1.1.15 | Counter | read-only | This entry is a variable that registers the number of frames received with no receiver above who desires to see those packets. |
| CTR scoNicMcastRjct | 1.3.6.1.4.1.1050.25.2.4.1.1.16 | Counter | read-only | This entry is a variable that registers the number of multicast frames received that were not in the multicast table. |
| CTR scoNicCarrier | 1.3.6.1.4.1.1050.25.2.4.1.1.17 | Counter | read-only | This entry is a variable that registers the number of transmitted frames aborted due to carrier loss during transmission. |
| CTR scoNicBadCts | 1.3.6.1.4.1.1050.25.2.4.1.1.18 | Counter | read-only | This entry is a variable that registers the number of transmitted frames aborted due to loss of the CTS signal during transmission. |
| CTR scoNicBadDma | 1.3.6.1.4.1.1050.25.2.4.1.1.19 | Counter | read-only | This entry is a variable that registers the number of DMA over/under runs. |
| CTR scoNicTimeOuts | 1.3.6.1.4.1.1050.25.2.4.1.1.20 | Counter | read-only | This entry is the number of device timeouts. |
| scoNicGenericThresholdTable | 1.3.6.1.4.1.1050.25.2.4.2 | not-accessible | This entry is a table of SCO NIC generic threshold values. | |
| scoNicGenericThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1 | not-accessible | This entry is the threshold value for each SCO NIC generic counter. | |
| INT scoNicNumRcvPktsThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.1 | INTEGER | read-write | This entry is the current threshold value of received packets in this NIC card. |
| INT scoNicNumRcvBytesThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.2 | INTEGER | read-write | This entry is the current threshold value of received bytes in this NIC card. |
| INT scoNicNumSndPktsThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.3 | INTEGER | read-write | This entry is the current threshold value of sent packets in this NIC card. |
| INT scoNicNumSndBytesThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.4 | INTEGER | read-write | This entry is the current threshold value of sent bytes in this NIC card. |
| INT scoNicFrameDefThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.5 | INTEGER | read-write | This entry is the current threshold value for deferred frames. |
| INT scoNicCollisionsThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.6 | INTEGER | read-write | This entry is the current threshold value of total collisions. |
| INT scoNicFrameCollThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.7 | INTEGER | read-write | This entry is the current threshold value of frames involved in a collision. |
| INT scoNicOFrameCollThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.8 | INTEGER | read-write | This entry is the current threshold value for out of frame collisions. |
| INT scoNicXsCollThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.9 | INTEGER | read-write | This entry is the current threshold value of frames dropped due to excessive collisions. |
| INT scoNicFrameNosrThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.10 | INTEGER | read-write | This entry is the current threshold value of frames dropped due to no streams. |
| INT scoNicNoResourceThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.11 | INTEGER | read-write | This entry is the current threshold value of frames dropped due to no resource. |
| INT scoNicBadSumThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.12 | INTEGER | read-write | This entry is the current threshold value of bad checksums received. |
| INT scoNicAlignThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.13 | INTEGER | read-write | This entry is the current threshold value of bad alignment received. |
| INT scoNicBadLenThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.14 | INTEGER | read-write | This entry is the current threshold value of bad length received. |
| INT scoNicBadSapThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.15 | INTEGER | read-write | This entry is the current threshold value of bad SAP received. |
| INT scoNicMcastRjctThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.16 | INTEGER | read-write | This entry is the current threshold value of multicast frames rejected. |
| INT scoNicCarrierThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.17 | INTEGER | read-write | This entry is the current threshold value of errors due to lost carriers. |
| INT scoNicBadCtsThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.18 | INTEGER | read-write | This entry is the current threshold value of errors due to lost CTS. |
| INT scoNicBadDmaThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.19 | INTEGER | read-write | This entry is the current threshold value of DMA over/under runs. |
| INT scoNicTimeOutsThreshold | 1.3.6.1.4.1.1050.25.2.4.2.1.20 | INTEGER | read-write | This entry is the current threshold value for device timeouts. |
| ntNic | 1.3.6.1.4.1.1050.25.2.5 | |||
| ntNicGenericCounterTable | 1.3.6.1.4.1.1050.25.2.5.1 | not-accessible | This entry is a table of Windows NT NIC generic counters. | |
| ntNicGenericCounter | 1.3.6.1.4.1.1050.25.2.5.1.1 | not-accessible | This entry contains information about each Windows NT NIC generic counter. | |
| CTR ntNicCntFrameXmitOk | 1.3.6.1.4.1.1050.25.2.5.1.1.1 | Counter | read-only | This entry is the number of frames transmitted without errors. |
| CTR ntNicCntFrameRcvOk | 1.3.6.1.4.1.1050.25.2.5.1.1.2 | Counter | read-only | This entry is the number of frames the NIC received with no errors. |
| CTR ntNicCntFrameXmitErr | 1.3.6.1.4.1.1050.25.2.5.1.1.3 | Counter | read-only | This entry is the number of frames the NIC fails to transmit. |
| CTR ntNicCntFrameRcvErr | 1.3.6.1.4.1.1050.25.2.5.1.1.4 | Counter | read-only | This entry is the number of frames the NIC receives but is abandoned due to errors. |
| CTR ntNicCntRcvFailNoBuf | 1.3.6.1.4.1.1050.25.2.5.1.1.5 | Counter | read-only | This entry is the number of frames the NIC cannot receive due to lack of buffer space. |
| CTR ntNicCntDirByteXmit | 1.3.6.1.4.1.1050.25.2.5.1.1.6 | Counter | read-only | This entry is the number of bytes in directed packets transmitted without errors. |
| CTR ntNicCntDirPktXmit | 1.3.6.1.4.1.1050.25.2.5.1.1.7 | Counter | read-only | This entry is the number of directed packets transmitted without errors. |
| CTR ntNicCntMulCastByteXmit | 1.3.6.1.4.1.1050.25.2.5.1.1.8 | Counter | read-only | This entry is the number of bytes in multicast packets transmitted without errors. |
| CTR ntNicCntMulCastPktXmit | 1.3.6.1.4.1.1050.25.2.5.1.1.9 | Counter | read-only | This entry is the number of multicast packets transmitted without errors. |
| CTR ntNicCntBrdCastByteXmit | 1.3.6.1.4.1.1050.25.2.5.1.1.10 | Counter | read-only | This entry is the number of bytes in broadcast packets transmitted without errors. |
| CTR ntNicCntBrdCastPktXmit | 1.3.6.1.4.1.1050.25.2.5.1.1.11 | Counter | read-only | This entry is the number of broadcast packets transmitted without errors. |
| CTR ntNicCntDirByteRcv | 1.3.6.1.4.1.1050.25.2.5.1.1.12 | Counter | read-only | This entry is the number of bytes in directed packets received without errors. |
| CTR ntNicCntDirPktRcv | 1.3.6.1.4.1.1050.25.2.5.1.1.13 | Counter | read-only | This entry is the number of directed packets received without errors. |
| CTR ntNicCntMulCastByteRcv | 1.3.6.1.4.1.1050.25.2.5.1.1.14 | Counter | read-only | This entry is the number of bytes in multicast packets received without errors. |
| CTR ntNicCntMulCastPktRcv | 1.3.6.1.4.1.1050.25.2.5.1.1.15 | Counter | read-only | This entry is the number of multicast packets received without errors. |
| CTR ntNicCntBrdCastByteRcv | 1.3.6.1.4.1.1050.25.2.5.1.1.16 | Counter | read-only | This entry is the number of bytes in broadcast packets received without errors. |
| CTR ntNicCntBrdCastPktRcv | 1.3.6.1.4.1.1050.25.2.5.1.1.17 | Counter | read-only | This entry is the number of broadcast packets received without errors. |
| CTR ntNicCntFrameRcvCRCErr | 1.3.6.1.4.1.1050.25.2.5.1.1.18 | Counter | read-only | This entry is the number of frames received with checksum errors. |
| INT ntNicXmitQueueLength | 1.3.6.1.4.1.1050.25.2.5.1.1.19 | INTEGER | read-only | This entry is the number of packets the NIC driver queues for transmission. |
| ntNicGenericThresholdTable | 1.3.6.1.4.1.1050.25.2.5.2 | not-accessible | This entry is a table of threshold values for Windows NT NIC generic counters. | |
| ntNicGenericThreshold | 1.3.6.1.4.1.1050.25.2.5.2.1 | not-accessible | This entry contains the threshold value for each Windows NT NIC generic counter. | |
| INT ntNicTldFrameXmitOk | 1.3.6.1.4.1.1050.25.2.5.2.1.1 | INTEGER | read-write | This entry is the threshold value of frames transmitted without errors. |
| INT ntNicTldFrameRcvOk | 1.3.6.1.4.1.1050.25.2.5.2.1.2 | INTEGER | read-write | This entry is the threshold value of frames the NIC receives with no errors. |
| INT ntNicTldFrameXmitErr | 1.3.6.1.4.1.1050.25.2.5.2.1.3 | INTEGER | read-write | This entry is the threshold value of frames the NIC fails to transmit. |
| INT ntNicTldFrameRcvErr | 1.3.6.1.4.1.1050.25.2.5.2.1.4 | INTEGER | read-write | This entry is the threshold value of frames the NIC receives but are abandoned due to errors. |
| INT ntNicTldRcvFailNoBuf | 1.3.6.1.4.1.1050.25.2.5.2.1.5 | INTEGER | read-write | This entry is the threshold value of frames the NIC cannot receive due to lack of buffer space. |
| INT ntNicTldDirByteXmit | 1.3.6.1.4.1.1050.25.2.5.2.1.6 | INTEGER | read-write | This entry is the threshold value of bytes in directed packets transmitted without errors. |
| INT ntNicTldDirPktXmit | 1.3.6.1.4.1.1050.25.2.5.2.1.7 | INTEGER | read-write | This entry is the threshold value of directed packets transmitted without errors. |
| INT ntNicTldMulCastByteXmit | 1.3.6.1.4.1.1050.25.2.5.2.1.8 | INTEGER | read-write | This entry is the threshold value of bytes in multicast packets transmitted without errors. |
| INT ntNicTldMulCastPktXmit | 1.3.6.1.4.1.1050.25.2.5.2.1.9 | INTEGER | read-write | This entry is the threshold value of multicast packets transmitted without errors. |
| INT ntNicTldBrdCastByteXmit | 1.3.6.1.4.1.1050.25.2.5.2.1.10 | INTEGER | read-write | This entry is the threshold value of bytes in broadcast packets transmitted without errors. |
| INT ntNicTldBrdCastPktXmit | 1.3.6.1.4.1.1050.25.2.5.2.1.11 | INTEGER | read-write | This entry is the threshold value of broadcast packets transmitted without errors. |
| INT ntNicTldDirByteRcv | 1.3.6.1.4.1.1050.25.2.5.2.1.12 | INTEGER | read-write | This entry is the threshold value of bytes in directed packets received without errors. |
| INT ntNicTldDirPktRcv | 1.3.6.1.4.1.1050.25.2.5.2.1.13 | INTEGER | read-write | This entry is the threshold value of directed packets received without errors. |
| INT ntNicTldMulCastByteRcv | 1.3.6.1.4.1.1050.25.2.5.2.1.14 | INTEGER | read-write | This entry is the threshold value of bytes in multicast packets received without errors. |
| INT ntNicTldMulCastPktRcv | 1.3.6.1.4.1.1050.25.2.5.2.1.15 | INTEGER | read-write | This entry is the threshold value of multicast packets received without errors. |
| INT ntNicTldBrdCastByteRcv | 1.3.6.1.4.1.1050.25.2.5.2.1.16 | INTEGER | read-write | This entry is the threshold value of bytes in broadcast packets received without errors. |
| INT ntNicTldBrdCastPktRcv | 1.3.6.1.4.1.1050.25.2.5.2.1.17 | INTEGER | read-write | This entry is the threshold value of broadcast packets received without errors. |
| INT ntNicTldFrameRcvCRCErr | 1.3.6.1.4.1.1050.25.2.5.2.1.18 | INTEGER | read-write | This entry is the threshold value of frames received with checksum errors. |
| INT ntNicTldXmitQueueLength | 1.3.6.1.4.1.1050.25.2.5.2.1.19 | INTEGER | read-write | This entry is the threshold value of packets the NIC driver queues for transmission. |
| ntNicEthernetCounterTable | 1.3.6.1.4.1.1050.25.2.5.3 | not-accessible | This entry is a table of Windows NT NIC Ethernet counters. | |
| ntNicEthernetCounter | 1.3.6.1.4.1.1050.25.2.5.3.1 | not-accessible | This entry contains information about each Windows NT NIC Ethernet counter. | |
| CTR ntNicCntRcvFrameAlignErr | 1.3.6.1.4.1.1050.25.2.5.3.1.1 | Counter | read-only | This entry is the number of frames received with alignment errors. |
| CTR ntNicCntXmitOkOneCollision | 1.3.6.1.4.1.1050.25.2.5.3.1.2 | Counter | read-only | This entry is the number of frames successfully transmitted after exactly one collision. |
| CTR ntNicCntXmitOkMoreCollision | 1.3.6.1.4.1.1050.25.2.5.3.1.3 | Counter | read-only | This entry is the number of frames successfully transmitted after more than one collision. |
| CTR ntNicCntXmitOkDeffered | 1.3.6.1.4.1.1050.25.2.5.3.1.4 | Counter | read-only | This entry is the number of frames successfully transmitted after the NIC defers transmission at least once. |
| CTR ntNicCntXmitFailMaxCollision | 1.3.6.1.4.1.1050.25.2.5.3.1.5 | Counter | read-only | This entry is the number of frames not transmitted due to excessive collisions. |
| CTR ntNicCntRcvErrOverrun | 1.3.6.1.4.1.1050.25.2.5.3.1.6 | Counter | read-only | This entry is the number of frames not received due to over-run errors. |
| CTR ntNicCntXmitErrUnderrun | 1.3.6.1.4.1.1050.25.2.5.3.1.7 | Counter | read-only | This entry is the number of frames not transmitted due to under-run errors. |
| CTR ntNicCntXmitHeartbeat | 1.3.6.1.4.1.1050.25.2.5.3.1.8 | Counter | read-only | This entry is the number of frames successfully transmitted without detection of the collision-detect heartbeat. |
| CTR ntNicCntTimesCRSLost | 1.3.6.1.4.1.1050.25.2.5.3.1.9 | Counter | read-only | This entry is the number of times the CRS signal has been lost during packet transmission. |
| CTR ntNicCntXmitLateCollision | 1.3.6.1.4.1.1050.25.2.5.3.1.10 | Counter | read-only | This entry is the number of collisions detected after the normal window. |
| ntNicEthernetThresholdTable | 1.3.6.1.4.1.1050.25.2.5.4 | not-accessible | This entry is a table of threshold values for Windows NT NIC Ethernet counters. | |
| ntNicEthernetThreshold | 1.3.6.1.4.1.1050.25.2.5.4.1 | not-accessible | This entry contains the threshold value for each Windows NT NIC Ethernet counter. | |
| INT ntNicTldRcvFrameAlignErr | 1.3.6.1.4.1.1050.25.2.5.4.1.1 | INTEGER | read-write | This entry is the threshold value of frames received with alignment errors. |
| INT ntNicTldXmitOkOneCollision | 1.3.6.1.4.1.1050.25.2.5.4.1.2 | INTEGER | read-write | This entry is the threshold value of frames successfully transmitted after exactly one collision. |
| INT ntNicTldXmitOkMoreCollision | 1.3.6.1.4.1.1050.25.2.5.4.1.3 | INTEGER | read-write | This entry is the threshold value of frames successfully transmitted after more than one collision. |
| INT ntNicTldXmitOkDeffered | 1.3.6.1.4.1.1050.25.2.5.4.1.4 | INTEGER | read-write | This entry is the threshold value of frames successfully transmitted after the NIC defers transmission at least once. |
| INT ntNicTldXmitFailMaxCollision | 1.3.6.1.4.1.1050.25.2.5.4.1.5 | INTEGER | read-write | This entry is the threshold value of frames not transmitted due to excessive collisions. |
| INT ntNicTldRcvErrOverrun | 1.3.6.1.4.1.1050.25.2.5.4.1.6 | INTEGER | read-write | This entry is the threshold value of frames not received due to over-run errors. |
| INT ntNicTldXmitErrUnderrun | 1.3.6.1.4.1.1050.25.2.5.4.1.7 | INTEGER | read-write | This entry is the threshold value of frames not transmitted due to under-run errors. |
| INT ntNicTldXmitHeartbeat | 1.3.6.1.4.1.1050.25.2.5.4.1.8 | INTEGER | read-write | This entry is the threshold value of frames successfully transmitted without detection of the collision-detect heartbeat. |
| INT ntNicTldTimesCRSLost | 1.3.6.1.4.1.1050.25.2.5.4.1.9 | INTEGER | read-write | This entry is the threshold value for the number of times the CRS signal has been lost during packet transmission. |
| INT ntNicTldXmitLateCollision | 1.3.6.1.4.1.1050.25.2.5.4.1.10 | INTEGER | read-write | This entry is the threshold value of collisions detected after the normal window. |
| ntNicTokenRingCounterTable | 1.3.6.1.4.1.1050.25.2.5.5 | not-accessible | This entry is a table of Windows NT NIC Token Ring counters. | |
| ntNicTokenRingCounter | 1.3.6.1.4.1.1050.25.2.5.5.1 | not-accessible | This entry contains information about each Windows NT NIC Token Ring counter. | |
| CTR ntNicCntACError | 1.3.6.1.4.1.1050.25.2.5.5.1.1 | Counter | read-only | This entry is the number of frames with A/C errors. |
| CTR ntNicCntAbortDelimiter | 1.3.6.1.4.1.1050.25.2.5.5.1.2 | Counter | read-only | This entry is the number of abort delimiters transmitted. |
| CTR ntNicCntBurstError | 1.3.6.1.4.1.1050.25.2.5.5.1.3 | Counter | read-only | This entry is the number of frames containing five half bits with no transition. |
| CTR ntNicCntFrameCopiedError | 1.3.6.1.4.1.1050.25.2.5.5.1.4 | Counter | read-only | This entry is the number of frames addressed to the network interface card that another NIC on the ring has also copied. |
| CTR ntNicCntFrequencyError | 1.3.6.1.4.1.1050.25.2.5.5.1.5 | Counter | read-only | This entry is the number of frequency errors on the ring. |
| CTR ntNicCntInternalError | 1.3.6.1.4.1.1050.25.2.5.5.1.6 | Counter | read-only | This entry is the number of internal errors the NIC has detected. |
| CTR ntNicCntLastRingStatus | 1.3.6.1.4.1.1050.25.2.5.5.1.7 | Counter | read-only | This entry is an NDIS_STATUS_RING_STATUS code indicates the last ring status. |
| CTR ntNicCntLineError | 1.3.6.1.4.1.1050.25.2.5.5.1.8 | Counter | read-only | This entry is the number of frames with an invalid FCS or a code violation. |
| CTR ntNicCntLostFrame | 1.3.6.1.4.1.1050.25.2.5.5.1.9 | Counter | read-only | This entry is the number of frames transmitted that have not circled the ring within the maximum ring latency. |
| CTR ntNicCntTokenError | 1.3.6.1.4.1.1050.25.2.5.5.1.10 | Counter | read-only | This entry is the number of times the NIC has been the active monitor and has had to recreate. |
| ntNicTokenRingThresholdTable | 1.3.6.1.4.1.1050.25.2.5.6 | not-accessible | This entry is a table of threshold values for Windows NT NIC Token Ring counters. | |
| ntNicTokenRingThreshold | 1.3.6.1.4.1.1050.25.2.5.6.1 | not-accessible | This entry contains the threshold value for each Windows NT NIC Token Ring counter. | |
| INT ntNicTldACError | 1.3.6.1.4.1.1050.25.2.5.6.1.1 | INTEGER | read-write | This entry is the threshold value of frames with A/C errors. |
| INT ntNicTldAbortDelimiter | 1.3.6.1.4.1.1050.25.2.5.6.1.2 | INTEGER | read-write | This entry is the threshold value of abort delimiters transmitted. |
| INT ntNicTldBurstError | 1.3.6.1.4.1.1050.25.2.5.6.1.3 | INTEGER | read-write | This entry is the threshold value of frames containing five half bits with no transition. |
| INT ntNicTldFrameCopiedError | 1.3.6.1.4.1.1050.25.2.5.6.1.4 | INTEGER | read-write | This entry is the threshold value of frames addressed to the network interface card that another NIC on the ring has also copied. |
| INT ntNicTldFrequencyError | 1.3.6.1.4.1.1050.25.2.5.6.1.5 | INTEGER | read-write | This entry is the threshold value of frequency errors on the ring. |
| INT ntNicTldInternalError | 1.3.6.1.4.1.1050.25.2.5.6.1.6 | INTEGER | read-write | This entry is the threshold value of internal errors the NIC has detected. |
| INT ntNicTldLastRingStatus | 1.3.6.1.4.1.1050.25.2.5.6.1.7 | INTEGER | read-write | This entry is the threshold value of the last ring status. |
| INT ntNicTldLineError | 1.3.6.1.4.1.1050.25.2.5.6.1.8 | INTEGER | read-write | This entry is the threshold value of the number of frames with an invalid FCS or a code violation. |
| INT ntNicTldLostFrame | 1.3.6.1.4.1.1050.25.2.5.6.1.9 | INTEGER | read-write | This entry is the threshold value for the number of frames transmitted that have not circled the ring within the maximum ring latency. |
| INT ntNicTldTokenError | 1.3.6.1.4.1.1050.25.2.5.6.1.10 | INTEGER | read-write | This entry is the threshold value for the number of times the NIC has been the active monitor and has had to recreate. |
| INT glbThldNicByte | 1.3.6.1.4.1.1050.25.2.6 | INTEGER | read-write | This entry is the global threshold setting for NIC received/transmitted bytes. Default is 100Mbps/8 = 12500000. |
| INT glbThldNicPacket | 1.3.6.1.4.1.1050.25.2.7 | INTEGER | read-write | This entry is the global threshold setting for NIC received/transmitted packets. Default is 100Mbps/8/50 = 250000. |
| INT glbThldNicFault | 1.3.6.1.4.1.1050.25.2.8 | INTEGER | read-write | This entry is the global threshold setting for NIC fault counters. Default is 0xFFFFFFFF, therefore, no SNMP traps will be sent. |
| systemBoard | 1.3.6.1.4.1.1050.25.3 | |||
| systemIrqsInfoTable | 1.3.6.1.4.1.1050.25.3.1 | not-accessible | This entry is a table containing IRQ numbers and the devices occupying each IRQ. | |
| systemIrqsInfoEntry | 1.3.6.1.4.1.1050.25.3.1.1 | not-accessible | This entry contains information about each IRQ. | |
| INT irqNumber | 1.3.6.1.4.1.1050.25.3.1.1.1 | INTEGER | read-only | This entry is the IRQ number. |
| STR irqOccupiedDes | 1.3.6.1.4.1.1050.25.3.1.1.2 | DisplayString | read-only | This entry contains information about the device occupying the IRQ. |
| systemDmasInfoTable | 1.3.6.1.4.1.1050.25.3.2 | not-accessible | This entry is a table containing DMA channels and the devices occupying each channel. | |
| systemDmasInfoEntry | 1.3.6.1.4.1.1050.25.3.2.1 | not-accessible | This entry contains information about each DMA channel. | |
| INT dmaChannel | 1.3.6.1.4.1.1050.25.3.2.1.1 | INTEGER | read-only | This entry is the DMA channel. |
| STR dmaOccupiedDes | 1.3.6.1.4.1.1050.25.3.2.1.2 | DisplayString | read-only | This entry contains information about the device occupying the DMA channel. |
| INT totalIoPortsNum | 1.3.6.1.4.1.1050.25.3.3 | INTEGER | read-only | This entry shows the number of I/O ports. |
| systemIoPortsInfoTable | 1.3.6.1.4.1.1050.25.3.4 | not-accessible | This entry is a table containing I/O port information and the devices occupying each port. | |
| systemIoPortsInfoEntry | 1.3.6.1.4.1.1050.25.3.4.1 | not-accessible | This entry contains information about each I/O port. | |
| INT ioPortsIndex | 1.3.6.1.4.1.1050.25.3.4.1.1 | INTEGER | read-only | This entry is an index to the I/O port table. |
| INT ioPortsBeginValue | 1.3.6.1.4.1.1050.25.3.4.1.2 | INTEGER | read-only | This entry shows the starting address of the I/O port. |
| INT ioPortsEndValue | 1.3.6.1.4.1.1050.25.3.4.1.3 | INTEGER | read-only | This entry shows the ending address of the I/O port. |
| STR ioPortsOccupiedDes | 1.3.6.1.4.1.1050.25.3.4.1.4 | DisplayString | read-only | This entry contains information about the I/O device occupying the port. |
| systemSlotsInfoTable | 1.3.6.1.4.1.1050.25.3.5 | not-accessible | This entry is a table containing information about system slots. | |
| systemSlotsInfoEntry | 1.3.6.1.4.1.1050.25.3.5.1 | not-accessible | This entry contains information about each system slot. | |
| INT slotsNumber | 1.3.6.1.4.1.1050.25.3.5.1.1 | INTEGER | read-only | This entry shows the slot number. |
| SLO slotsType | 1.3.6.1.4.1.1050.25.3.5.1.2 | SlotsType | read-only | This entry shows the slot type, EISA, ISA, or PCI. 0 = Unknown 1 = EISA 3 = ISA 5 = PCI |
| STR slotsOccupiedDes | 1.3.6.1.4.1.1050.25.3.5.1.3 | DisplayString | read-only | This entry shows the device installed on this slot. |
| INT totalMemSlotsNum | 1.3.6.1.4.1.1050.25.3.6 | INTEGER | read-only | This entry shows the number of SIMM slots. |
| memoryTable | 1.3.6.1.4.1.1050.25.3.7 | not-accessible | This entry is a table containing system memory information. | |
| memoryEntry | 1.3.6.1.4.1.1050.25.3.7.1 | not-accessible | This entry contains information about each SIMM slot. | |
| INT memSlots | 1.3.6.1.4.1.1050.25.3.7.1.1 | INTEGER | read-only | This entry contains information about the memory module installed on the SIMM slot. |
| OCT simmType | 1.3.6.1.4.1.1050.25.3.7.1.2 | OCTET STRING | read-only | This entry shows the memory module size in MB. |
| STR systemBootControl | 1.3.6.1.4.1.1050.25.3.11 | DisplayString | read-only | This entry shows boot control information. |
| STR systemFloppyControl | 1.3.6.1.4.1.1050.25.3.12 | DisplayString | read-only | This entry shows diskette drive control information. |
| STR systemHddControl | 1.3.6.1.4.1.1050.25.3.13 | DisplayString | read-only | This entry shows hard disk control information. |
| INT totalBaseMemNum | 1.3.6.1.4.1.1050.25.3.14 | INTEGER | read-only | This entry shows the number of base memory blocks used by I/O devices. |
| systemBaseMemTable | 1.3.6.1.4.1.1050.25.3.15 | not-accessible | This entry is a table containing information about base memory used by I/O devices. | |
| systemBaseMemEntry | 1.3.6.1.4.1.1050.25.3.15.1 | not-accessible | This entry contains information about each base memory block. | |
| INT baseMemIndex | 1.3.6.1.4.1.1050.25.3.15.1.1 | INTEGER | read-only | This entry is an index to the base memory table. |
| INT baseMemAddr | 1.3.6.1.4.1.1050.25.3.15.1.2 | INTEGER | read-only | This entry shows the starting address of the block of base memory used. |
| INT baseMemLength | 1.3.6.1.4.1.1050.25.3.15.1.3 | INTEGER | read-only | This entry shows the length of the block of base memory used. |
| STR baseMemOccupiedDes | 1.3.6.1.4.1.1050.25.3.15.1.4 | DisplayString | read-only | This entry contains a description of the device using the block of base memory. |
| serverEnvrm | 1.3.6.1.4.1.1050.25.4 | |||
| STR productName | 1.3.6.1.4.1.1050.25.4.1 | DisplayString | read-only | This entry shows the machine product name. |
| STR osVersion | 1.3.6.1.4.1.1050.25.4.2 | DisplayString | read-only | This entry shows information about the current operating system in use. |
| STR expanBusType | 1.3.6.1.4.1.1050.25.4.3 | DisplayString | read-only | This entry shows information about expansion slots. A system may contain one or more of the following types: ISA, EISA, PCI, VESA, etc. |
| STR processorType | 1.3.6.1.4.1.1050.25.4.4 | DisplayString | read-only | This entry shows the server's CPU information. |
| INT systemIntrlCache | 1.3.6.1.4.1.1050.25.4.5 | INTEGER | read-only | This entry shows the CPU's internal cache size in KB. |
| INT systemExtrlCache | 1.3.6.1.4.1.1050.25.4.6 | INTEGER | read-only | This shows the server's external cache size in KB. |
| INT systemTotalMemory | 1.3.6.1.4.1.1050.25.4.7 | INTEGER | read-only | This entry shows the system's total memory size in bytes. |
| INT systemFreeMemory | 1.3.6.1.4.1.1050.25.4.8 | INTEGER | read-only | This entry shows the system's current free memory size in bytes. |
| STR systemSerialPort1Info | 1.3.6.1.4.1.1050.25.4.9 | DisplayString | read-only | This entry contains information about the system's serial port 1. |
| STR systemSerialPort2Info | 1.3.6.1.4.1.1050.25.4.10 | DisplayString | read-only | This entry contains information about the system's serial port 2. |
| STR systemParallelPortInfo | 1.3.6.1.4.1.1050.25.4.11 | DisplayString | read-only | This entry contains information about the system's parallel port. |
| STR keyboardType | 1.3.6.1.4.1.1050.25.4.12 | DisplayString | read-only | This entry shows the system's keyboard type. |
| STR videoType | 1.3.6.1.4.1.1050.25.4.13 | DisplayString | read-only | This entry shows the system's display type. |
| STR mouseType | 1.3.6.1.4.1.1050.25.4.14 | DisplayString | read-only | This entry shows the system's mouse type. |
| STR sysBiosVer | 1.3.6.1.4.1.1050.25.4.15 | DisplayString | read-only | This entry shows the system BIOS version. |
| STR serverName | 1.3.6.1.4.1.1050.25.4.16 | DisplayString | read-only | This entry shows the server name. |
| STR serverUpTime | 1.3.6.1.4.1.1050.25.4.17 | DisplayString | read-only | This entry shows the amount of time the server has been running. |
| serverMgrContactInfoTable | 1.3.6.1.4.1.1050.25.4.18 | not-accessible | This entry is a table containing information about all server managers. | |
| serverMgrContactInfoEntry | 1.3.6.1.4.1.1050.25.4.18.1 | not-accessible | This entry shows information about each server manager. | |
| STR serverMgrName | 1.3.6.1.4.1.1050.25.4.18.1.1 | DisplayString | read-write | This entry shows the server manager's name. |
| STR serverMgrOffPhone | 1.3.6.1.4.1.1050.25.4.18.1.2 | DisplayString | read-write | This entry shows the server manager's office phone number. |
| STR serverMgrOffAddr | 1.3.6.1.4.1.1050.25.4.18.1.3 | DisplayString | read-write | This entry shows the server manager's office address. |
| STR serverMgrHomePhone | 1.3.6.1.4.1.1050.25.4.18.1.4 | DisplayString | read-write | This entry shows the server manager's home phone number. |
| STR serverMgrHomeAddr | 1.3.6.1.4.1.1050.25.4.18.1.5 | DisplayString | read-write | This entry shows the server manager's home address. |
| STR serverMgrPagerNum | 1.3.6.1.4.1.1050.25.4.18.1.6 | DisplayString | read-write | This entry shows the server manager's pager number. |
| STR serverMgrEmailAddr | 1.3.6.1.4.1.1050.25.4.18.1.7 | DisplayString | read-write | This entry shows the server manager's email address. |
| INT serverMgrNumber | 1.3.6.1.4.1.1050.25.4.18.1.8 | INTEGER | read-only | This entry is the server manager number starting from 0. |
| STR serverLoc | 1.3.6.1.4.1.1050.25.4.19 | DisplayString | read-write | This entry shows the server's physical location. |
| INT totalSysVolNum | 1.3.6.1.4.1.1050.25.4.20 | INTEGER | read-only | This entry shows the total number of system volumes. |
| sysVolTable | 1.3.6.1.4.1.1050.25.4.21 | not-accessible | This entry is a table containing information about all system volumes. | |
| sysVolEntry | 1.3.6.1.4.1.1050.25.4.21.1 | not-accessible | This entry shows information about each system volume. | |
| INT sysVolNum | 1.3.6.1.4.1.1050.25.4.21.1.1 | INTEGER | read-only | This entry is the volume number. |
| STR sysVolName | 1.3.6.1.4.1.1050.25.4.21.1.2 | DisplayString | read-only | This entry shows the system volume name. |
| INT totalVolSize | 1.3.6.1.4.1.1050.25.4.21.1.3 | INTEGER | read-only | This entry shows the size of each system volume in KB. |
| INT freeVolSize | 1.3.6.1.4.1.1050.25.4.21.1.4 | INTEGER | read-only | This entry shows the current free size of a system volume in KB. |
| INT totalDirSize | 1.3.6.1.4.1.1050.25.4.21.1.5 | INTEGER | read-only | For NetWare, this entry shows the maximum number of directories that can be created in a system volume. For Windows NT, this entry shows the number of allocation units in a system volume. |
| INT freeDirSize | 1.3.6.1.4.1.1050.25.4.21.1.6 | INTEGER | read-only | For NetWare, this entry shows the current number of directories that can still be created in a system volume. For Windows NT, this entry shows the current number of free allocation units in a system volume. |
| INT usedVolSizeThreshold | 1.3.6.1.4.1.1050.25.4.21.1.7 | INTEGER | read-write | This entry shows the threshold setting (%) for a volume's usage. |
| INT totalSysPartitionNum | 1.3.6.1.4.1.1050.25.4.22 | INTEGER | read-only | This entry shows the total number of NetWare partitions created in the system. |
| sysPartitionTable | 1.3.6.1.4.1.1050.25.4.23 | not-accessible | This entry is a table containing information about all NetWare partitions in the system. | |
| sysPartitionEntry | 1.3.6.1.4.1.1050.25.4.23.1 | not-accessible | This entry contains information about each NetWare partition. | |
| INT sysPartitionNum | 1.3.6.1.4.1.1050.25.4.23.1.1 | INTEGER | read-only | This entry shows the system partition number assigned by the system. |
| INT partitionDiskNum | 1.3.6.1.4.1.1050.25.4.23.1.2 | INTEGER | read-only | This entry shows the disk number from which this partition is created. |
| INT dataAreaSize | 1.3.6.1.4.1.1050.25.4.23.1.3 | INTEGER | read-only | This entry shows the size of the partition's data area in sectors. |
| INT redirectionAreaSize | 1.3.6.1.4.1.1050.25.4.23.1.4 | INTEGER | read-only | This entry shows the size of the partition's redirection area in sectors. |
| INT redirectedSize | 1.3.6.1.4.1.1050.25.4.23.1.5 | INTEGER | read-only | This entry shows the number of sectors used in the partition's redirection area. |
| STR partitionName | 1.3.6.1.4.1.1050.25.4.23.1.6 | DisplayString | read-only | This entry shows the partition name. |
| INT softPollingInterval | 1.3.6.1.4.1.1050.25.4.27 | INTEGER | read-write | This entry shows the soft polling interval in seconds. By soft polling, it means that the Agent polls the system status (CPU Utilization, Memory Utilization, Volume Utilization and NIC Statistic Counters) based on a specified interval. Default is 1 second. |
| INT glbThldVolUtil | 1.3.6.1.4.1.1050.25.4.28 | INTEGER | read-write | This entry shows the global threshold value (%) for volume or file system utilization. Default is 100%. |
| INT numberOfCpu | 1.3.6.1.4.1.1050.25.4.29 | INTEGER | read-only | This entry shows the number of CPUs in the system. |
| cpuInfoTable | 1.3.6.1.4.1.1050.25.4.30 | not-accessible | This entry is a table containing information about all CPUs on the system. | |
| cpuInfo | 1.3.6.1.4.1.1050.25.4.30.1 | not-accessible | This entry shows information about each CPU. | |
| INT cpuNum | 1.3.6.1.4.1.1050.25.4.30.1.1 | INTEGER | read-only | This entry shows the CPU number starting at 0. |
| INT cpuUtilization | 1.3.6.1.4.1.1050.25.4.30.1.2 | INTEGER | read-only | This entry shows CPU utilization (%). |
| INT cpuSystemUtilization | 1.3.6.1.4.1.1050.25.4.30.1.9 | INTEGER | read-only | This entry shows CPU utilization (%) by the operating system. |
| INT cpuUserUtilization | 1.3.6.1.4.1.1050.25.4.30.1.10 | INTEGER | read-only | This entry shows CPU utilization (%) by applications. |
| INT cpuInterruptUtilization | 1.3.6.1.4.1.1050.25.4.30.1.11 | INTEGER | read-only | This entry shows CPU utilization (%) by the interrupt services. |
| OCT mgmtStationAddrSignIn | 1.3.6.1.4.1.1050.25.4.42 | OCTET STRING | read-write | This entry is the sign-in IPX address of the management station. |
| OCT mgmtStationAddrSignOut | 1.3.6.1.4.1.1050.25.4.43 | OCTET STRING | read-write | This entry is the sign-out IPX address of the management station. |
| INT serverTemp1Threshold | 1.3.6.1.4.1.1050.25.4.44 | INTEGER | read-write | This entry displays the first level threshold value for the system temperature. Values displayed have to be divided by ten (10) to show the temperature in degrees Celsius. For example, a reading of 305 means that the temperature is at 30.5 degrees Celsius. |
| INT serverTemp2Threshold | 1.3.6.1.4.1.1050.25.4.45 | INTEGER | read-write | This entry displays the second level threshold value for the CPU temperature. Values displayed have to be divided by ten (10) to show the temperature in degrees Celsius. For example, a reading of 305 means that the temperature is at 30.5 degrees Celsius. |
| INT serverCpuUtilizationThreshold | 1.3.6.1.4.1.1050.25.4.46 | INTEGER | read-write | This entry shows the threshold value (%) for the CPU utilization. |
| INT hostIOBusUtilizationThreshold | 1.3.6.1.4.1.1050.25.4.47 | INTEGER | read-write | This entry displays the threshold value for bus utilization. Values displayed have to be divided by one hundred (100) to show the percentage of bus utilization. For example, a reading of 1234 means that bus utilization is at 12.34%. |
| INT memoryUtilizedThreshold | 1.3.6.1.4.1.1050.25.4.48 | INTEGER | read-write | This entry shows the threshold value (%) for memory utilization. |
| INT totalSysFSNum | 1.3.6.1.4.1.1050.25.4.53 | INTEGER | read-only | This entry is the total number of SCO UNIX file systems. |
| sysFSTable | 1.3.6.1.4.1.1050.25.4.54 | not-accessible | This entry is a table containing all SCO UNIX file system information. | |
| sysFSEntry | 1.3.6.1.4.1.1050.25.4.54.1 | not-accessible | This entry contains information about each SCO UNIX file system. | |
| INT sysFSNumber | 1.3.6.1.4.1.1050.25.4.54.1.1 | INTEGER | read-only | This entry is an index of file systems information. |
| STR sysFSName | 1.3.6.1.4.1.1050.25.4.54.1.2 | DisplayString | read-only | This entry is the file system name. |
| INT totalFSSize | 1.3.6.1.4.1.1050.25.4.54.1.3 | INTEGER | read-only | This entry is the total size of a file system in KB. |
| INT freeFSSize | 1.3.6.1.4.1.1050.25.4.54.1.4 | INTEGER | read-only | This entry is the current free size of a file system in KB. |
| INT usedFSSizeThreshold | 1.3.6.1.4.1.1050.25.4.54.1.5 | INTEGER | read-write | This entry is the threshold value (%) of the file system currently in use. |
| INT totalFSinode | 1.3.6.1.4.1.1050.25.4.54.1.6 | INTEGER | read-only | This entry is the total inode counts of a file system. |
| INT freeFSinode | 1.3.6.1.4.1.1050.25.4.54.1.7 | INTEGER | read-only | This entry is the current free inode counts of a file system. |
| STR sysFSType | 1.3.6.1.4.1.1050.25.4.54.1.8 | DisplayString | read-only | This entry is the type of a file system. |
| STR sysFSMountTime | 1.3.6.1.4.1.1050.25.4.54.1.9 | DisplayString | read-only | This entry is the mount time of a file system. |
| dmiInfo | 1.3.6.1.4.1.1050.25.4.55 | |||
| STR biosVendor | 1.3.6.1.4.1.1050.25.4.55.1 | DisplayString | read-only | This entry displays the name of the BIOS vendor. |
| STR biosVersion | 1.3.6.1.4.1.1050.25.4.55.2 | DisplayString | read-only | This entry displays the BIOS version. |
| INT biosStartingAddressSegment | 1.3.6.1.4.1.1050.25.4.55.3 | INTEGER | read-only | This entry displays the segment location of the BIOS starting address, e.g. 0E800h. |
| STR biosReleaseDate | 1.3.6.1.4.1.1050.25.4.55.4 | DisplayString | read-only | This entry displays the BIOS release date in mm/dd/yy format. |
| INT biosROMSize | 1.3.6.1.4.1.1050.25.4.55.5 | INTEGER | read-only | This entry displays the ROM size of the BIOS. Size is 64K*(n+1). 0=64K, 1=128K, 2=256K, etc. |
| INT biosCharacteristics1 | 1.3.6.1.4.1.1050.25.4.55.6 | INTEGER | read-only | This entry displays the first 32 bits of BIOS characteristics. It defines which functions the BIOS supports. PCI, PCMCIA, Flash, etc. Bit 0 Reserved Bit 1 Reserved Bit 2 Unknown Bit 3 BIOS Characteristics Not Supported Bit 4 ISA is supported Bit 5 MCA is supported Bit 6 EISA is supported Bit 7 PCI is supported Bit 8 PCMCIA is supported Bit 9 Plug and Play is supported Bit 10 APM is supported Bit 11 BIOS is Upgradeable (Flash) Bit 12 BIOS shadowing is allowed Bit 13 VL-VESA is supported Bit 14 ESCD support is available Bit 15 Boot from CD is supported Bit 16 Selectable Boot is supported Bit 17 BIOS ROM is socketed Bit 18 Boot From PCMCIA is supported Bit 19 EDD (Enhanced Disk Drive) Specification is supported Bit 20 Int 13h - Japanese Floppy for NEC 9800 1.2mb (3.5 inch, 1k Bytes/Sector, 360 RPM) is supported Bit 21 Int 13h - Japanese Floppy for Toshiba 1.2mb (3.5 inch, 360 RPM) is supported Bit 22 Int 13h - 5.25 inch / 360 KB Floppy Services are supported Bit 23 Int 13h - 5.25 inch /1.2MB Floppy Services are supported Bit 24 Int 13h - 3.5 inch / 720 KB Floppy Services are supported Bit 25 Int 13h - 3.5 inch / 2.88 MB Floppy Services are supported Bit 26 Int 5h, Print Screen Service is supported Bit 27 Int 9h, 8042 Keyboard services are supported Bit 28 Int 14h, Serial Services are supported Bit 29 Int 17h, Printer Services are supported Bit 30 Int 10h, CGA Video Services are supported Bit 31 PC-98 Bits32:47 Reserved for BIOS Vendor Bits 48:63 Reserved for System Vendor |
| INT biosCharacteristics2 | 1.3.6.1.4.1.1050.25.4.55.7 | INTEGER | read-only | This entry displays the second 32 bits of BIOS characteristics. It defines which functions the BIOS supports. PCI, PCMCIA, Flash, etc. Bit 0 Reserved Bit 1 Reserved Bit 2 Unknown Bit 3 BIOS Characteristics Not Supported Bit 4 ISA is supported Bit 5 MCA is supported Bit 6 EISA is supported Bit 7 PCI is supported Bit 8 PCMCIA is supported Bit 9 Plug and Play is supported Bit 10 APM is supported Bit 11 BIOS is Upgradeable (Flash) Bit 12 BIOS shadowing is allowed Bit 13 VL-VESA is supported Bit 14 ESCD support is available Bit 15 Boot from CD is supported Bit 16 Selectable Boot is supported Bit 17 BIOS ROM is socketed Bit 18 Boot From PCMCIA is supported Bit 19 EDD (Enhanced Disk Drive) Specification is supported Bit 20 Int 13h - Japanese Floppy for NEC 9800 1.2mb (3.5 inch, 1k Bytes/Sector, 360 RPM) is supported Bit 21 Int 13h - Japanese Floppy for Toshiba 1.2mb (3.5 inch, 360 RPM) is supported Bit 22 Int 13h - 5.25 inch / 360 KB Floppy Services are supported Bit 23 Int 13h - 5.25 inch /1.2MB Floppy Services are supported Bit 24 Int 13h - 3.5 inch / 720 KB Floppy Services are supported Bit 25 Int 13h - 3.5 inch / 2.88 MB Floppy Services are supported Bit 26 Int 5h, Print Screen Service is supported Bit 27 Int 9h, 8042 Keyboard services are supported Bit 28 Int 14h, Serial Services are supported Bit 29 Int 17h, Printer Services are supported Bit 30 Int 10h, CGA Video Services are supported Bit 31 PC-98 Bits32:47 Reserved for BIOS Vendor Bits 48:63 Reserved for System Vendor |
| STR siManufacturer | 1.3.6.1.4.1.1050.25.4.55.8 | DisplayString | read-only | This entry displays the manufacturer of this computer system. |
| STR siProductName | 1.3.6.1.4.1.1050.25.4.55.9 | DisplayString | read-only | This entry displays the name of this product. |
| STR siVersion | 1.3.6.1.4.1.1050.25.4.55.10 | DisplayString | read-only | This entry displays the version number of this system. |
| STR siSerialNumber | 1.3.6.1.4.1.1050.25.4.55.11 | DisplayString | read-only | This entry displays the serial number of this system. |
| STR bbManufacturer | 1.3.6.1.4.1.1050.25.4.55.12 | DisplayString | read-only | This entry displays the base board manufacturer. |
| STR bbProductName | 1.3.6.1.4.1.1050.25.4.55.13 | DisplayString | read-only | This entry displays the base board product name. |
| STR bbVersion | 1.3.6.1.4.1.1050.25.4.55.14 | DisplayString | read-only | This entry displays the base board version. |
| STR bbSerialNumber | 1.3.6.1.4.1.1050.25.4.55.15 | DisplayString | read-only | This entry displays the base board serial number. |
| INT mcErrorDetectingMethod | 1.3.6.1.4.1.1050.25.4.55.16 | INTEGER | read-only | This entry displays the supported error detection method of the memory controller. 01h : Other 02h : Unknown 03h : None 04h : 8-bit Parity 05h : 32-bit ECC 06h : 64-bit ECC 07h : 128-bit ECC |
| INT mcErrorCorrectingCapability | 1.3.6.1.4.1.1050.25.4.55.17 | INTEGER | read-only | This entry displays the error correcting capability of the memory controller. Bit 0 : Other Bit 1 : Unknown Bit 2 : None Bit 3 : Single Bit Error Correcting Bit 4 : Double Bit Error Correcting Bit 5 : Error Scrubbing |
| INT mcSupportedInterleave | 1.3.6.1.4.1.1050.25.4.55.18 | INTEGER | read-only | This entry displays the supported memory interleave of the memory controller. 01h : Other 02h : Unknown 03h : One Way Interleave 04h : Two Way Interleave 05h : Four Way Interleave 06h : Eight Way Interleave 07h : Sixteen Way Interleave |
| INT mcCurrentInterleave | 1.3.6.1.4.1.1050.25.4.55.19 | INTEGER | read-only | This entry displays the current memory interleave of the memory controller. 01h : Other 02h : Unknown 03h : One Way Interleave 04h : Two Way Interleave 05h : Four Way Interleave 06h : Eight Way Interleave 07h : Sixteen Way Interleave |
| INT mcMaximumMemoryModuleSize | 1.3.6.1.4.1.1050.25.4.55.20 | INTEGER | read-only | This entry displays the size of the largest memory module supported (per slot), specified as n, where 2^n is the maximum size in MB. |
| INT mcSupportedSpeeds | 1.3.6.1.4.1.1050.25.4.55.21 | INTEGER | read-only | This entry displays the supported memory speeds of the memory controller. Bit 0 : Other Bit 1 : Unknown Bit 2 : 70ns Bit 3 : 60ns Bit 4 : 50ns Bit 5-15 : Reserved, must be zero |
| INT mcSupportedMemoryTypes | 1.3.6.1.4.1.1050.25.4.55.22 | INTEGER | read-only | This entry displays the supported memory types of the memory controller. Bit 0 : Other Bit 1 : Unknown Bit 2 : Standard Bit 3 : Fast Page Mode Bit 4 : EDO Bit 5 : Parity Bit 6 : ECC Bit 7 : SIMM Bit 8 : DIMM Bit 9-15 : Reserved, must be zero |
| INT mcMemoryModuleVoltage | 1.3.6.1.4.1.1050.25.4.55.23 | INTEGER | read-only | This entry describes the required voltages for each of the memory module sockets controlled by the controller: Bits 7:3 Reserved, must be zero Bit 2 2.9V Bit 1 3.3V Bit 0 5V NOTE: Setting of multiple bits indicates that sockets are configurable. |
| INT mcNumberOfAssociatedMemorySlots | 1.3.6.1.4.1.1050.25.4.55.24 | INTEGER | read-only | This entry defines how many of the Memory Module Information blocks are controlled by the controller. |
| INT piNumberOfProcessorInfo | 1.3.6.1.4.1.1050.25.4.55.25 | INTEGER | read-only | This field shows the number of entries in the piProcessorInfoTable. |
| INT mmNumberOfMemoryModuleInfo | 1.3.6.1.4.1.1050.25.4.55.26 | INTEGER | read-only | This entry shows the number of entries in the mmMemoryModuleInfoTable. |
| INT ciNumberOfCacheInfo | 1.3.6.1.4.1.1050.25.4.55.27 | INTEGER | read-only | This field shows the number of entries in the ciCacheInfoTable. |
| INT pcNumberOfPortConnectorInfo | 1.3.6.1.4.1.1050.25.4.55.28 | INTEGER | read-only | This field shows the number of entries in the pcPortConnectorInfoTable |
| INT ssNumberOfSystemSlotInfo | 1.3.6.1.4.1.1050.25.4.55.29 | INTEGER | read-only | This field shows the number of entries in ssSystemSlotInfoTable |
| INT obNumberOfOnBoardDeviceInfo | 1.3.6.1.4.1.1050.25.4.55.30 | INTEGER | read-only | This field shows the number of entries in the obOnBoardDeviceInfoTable. |
| INT oemNumberOfOEMString | 1.3.6.1.4.1.1050.25.4.55.31 | INTEGER | read-only | This field shows the number of entries in the oemStringTable. |
| INT smNumberOfEventLog | 1.3.6.1.4.1.1050.25.4.55.32 | INTEGER | read-only | This field shows the number of entries in the smEventLogTable. |
| INT smEventLogSupport | 1.3.6.1.4.1.1050.25.4.55.33 | INTEGER | read-only | This entry shows if BIOS supports System Event Log function: 0 = NO else = YES |
| INT smEventLogTotalSize | 1.3.6.1.4.1.1050.25.4.55.34 | INTEGER | read-only | This entry shows the total size of event log data area in bytes. |
| INT smEventLogUsedSize | 1.3.6.1.4.1.1050.25.4.55.35 | INTEGER | read-only | This entry shows the used size of event log data area in bytes. |
| INT smEventLogUtilizationThreshold | 1.3.6.1.4.1.1050.25.4.55.36 | INTEGER | read-write | This entry shows the threshold value (%) for event log data area utilization. |
| piProcessorInfoTable | 1.3.6.1.4.1.1050.25.4.55.52 | not-accessible | This entry is a table containing information about all types of processors on the system. | |
| piProcessorInfo | 1.3.6.1.4.1.1050.25.4.55.52.1 | not-accessible | This entry shows information about each processor. | |
| STR piSocketDesignation | 1.3.6.1.4.1.1050.25.4.55.52.1.1 | DisplayString | read-only | This entry displays the processor socket designation label on top of the base board. |
| INT piProcessorType | 1.3.6.1.4.1.1050.25.4.55.52.1.2 | INTEGER | read-only | This entry displays the processor type. 01H - other 02H - Unknown 03H - Central Processor 04H - Math Processor 05H - DSP Processor 06H - Video Processor |
| INT piProcessorFamily | 1.3.6.1.4.1.1050.25.4.55.52.1.3 | INTEGER | read-only | This entry displays the family to which this processor belongs to. 01H - other 02H - Unknown 03H - 8086 04H - 80286 05H - 80386 06H - 80486 07H - 8087 08H - 80287 09h - 80387 0AH - 80487 0BH - Pentium Family 0CH-11H - Reserved for specific Pentium versions 12H - M1 Family 13H-18H - Reserved for specific M1 versions 19H - K5 Family 1AH-1FH - Reserved for specific K5 versions 0CH - Future X86 Class CPUs 0DH - OverDrive Family |
| STR piProcessorManufacturer | 1.3.6.1.4.1.1050.25.4.55.52.1.4 | DisplayString | read-only | This entry displays the processor's manufacturer. |
| OCT piProcessorID | 1.3.6.1.4.1.1050.25.4.55.52.1.5 | OCTET STRING | read-only | This entry displays specific information which describes the processor's features. For x86 class CPUs. the field's format depends on the processor's support of the CPUID instruction. If the instruction is supported, the processor ID field contains 2 DWORD-formatted values. The first(offsets 08h - 0Bh)is the EAX value returned by a CPUID instruction with input EAX set to 1; the second(offset 0Ch-0Fh) is the EDX value returned by that instruction. Otherwise, only the first 2 bytes of the processor ID field are significant and contain the contents of the DX register at CPU reset. |
| STR piProcessorVersion | 1.3.6.1.4.1.1050.25.4.55.52.1.6 | DisplayString | read-only | This entry displays the processor version. |
| INT piVoltage | 1.3.6.1.4.1.1050.25.4.55.52.1.7 | INTEGER | read-only | This entry shows the processor's voltage requirement. Bits 7:4 Reserved, must be zero Bits 3:0 Voltage Capability. A Set bit indicates the voltage is supported. Bit 0 - 5V Bit 1 - 3.3V Bit 2 - 2.9V Bit 3 - Reserved, must be zero. Note: Setting of multiple bits indicates the socket is configurable. |
| INT piExternalClock | 1.3.6.1.4.1.1050.25.4.55.52.1.8 | INTEGER | read-only | This entry shows the processor's external clock frequency in MHz. If the value is unknown, the field is set to 0. |
| INT piMaxSpeed | 1.3.6.1.4.1.1050.25.4.55.52.1.9 | INTEGER | read-only | This entry shows the processor's maximum speed in MHz. If the value is unknown, the field is set to 0. |
| INT piCurrentSpeed | 1.3.6.1.4.1.1050.25.4.55.52.1.10 | INTEGER | read-only | This entry shows the processor's current speed in MHz. If the value is unknown, the field is set to 0. |
| INT piStatus | 1.3.6.1.4.1.1050.25.4.55.52.1.11 | INTEGER | read-only | This entry shows the status of this processor. Bit 6 CPU socket populated. 1 - CPU Socket Populated. 0 - CPU Socket Unpopulated. Bits 2:0 CPU Status 0h - Unknown 1h - CPU Enabled 2h - CPU disabled by user 3h - CPU disabled by system BIOS 4h - CPU is idle 5-6h Reserved 7h - Other |
| INT piProcessorUpgrade | 1.3.6.1.4.1.1050.25.4.55.52.1.12 | INTEGER | read-only | This entry shows the processor upgrade method. 01h - other 02h - unknown 03h - daughter board 04h - ZIF socket 05h - replaceable piggy back 06h - None 07h - LIF socket |
| mmMemoryModuleInfoTable | 1.3.6.1.4.1.1050.25.4.55.53 | not-accessible | This entry is a table containing information about all memory module sockets | |
| mmMemoryModuleInfo | 1.3.6.1.4.1.1050.25.4.55.53.1 | not-accessible | This entry shows information about each memory module. | |
| STR mmSocketDesignation | 1.3.6.1.4.1.1050.25.4.55.53.1.1 | DisplayString | read-only | This entry shows the memory socket designation labels on top of the base board. |
| INT mmBankConnections | 1.3.6.1.4.1.1050.25.4.55.53.1.2 | INTEGER | read-only | This entry shows the socket to which a memory module is installed. It is a single byte value, in this byte each nibble indicates a bank(RAS#) connection, 0xF means no connection. Example: If banks 1 & 3 (RAS# 1 & 3) were connected to a SIMM socket the byte for that socket would be 13h. If only bank 2 (RAS 2) were connected the byte for that socket would be 2Fh. |
| INT mmCurrentSpeed | 1.3.6.1.4.1.1050.25.4.55.53.1.3 | INTEGER | read-only | This entry shows the speed of the memory module, , in ns (e.g. 70d for a 70ns module). If the speed is unknown, the field is set to 0. |
| INT mmCurrentMemoryType | 1.3.6.1.4.1.1050.25.4.55.53.1.4 | INTEGER | read-only | This entry shows the type of memory module currently installed: Bit 0 - other Bit 1 - unknown Bit 2 - Standard Bit 3 - Fast Page Mode Bit 4 - EDO Bit 5 - Parity Bit 6 - ECC Bit 7 - SIMM Bit 8 - DIMM Bit 9:15 Reserved, must be 0 |
| INT mmInstalledSize | 1.3.6.1.4.1.1050.25.4.55.53.1.5 | INTEGER | read-only | This entry shows the installed memory size. Bits 0 - 6 represent the size(n), where 2^n is the size in MB. |
| INT mmEnabledSize | 1.3.6.1.4.1.1050.25.4.55.53.1.6 | INTEGER | read-only | This entry shows the enabled memory size. Bits 0 - 6 represent the size(n), where 2^n is the size in MB. |
| INT mmErrorStatus | 1.3.6.1.4.1.1050.25.4.55.53.1.7 | INTEGER | read-only | This entry shows the memory error status. Bit 1 - Correctable errors received for the module Bit 0 - Uncorrectable errors received for the module |
| ciCacheInfoTable | 1.3.6.1.4.1.1050.25.4.55.54 | not-accessible | This entry is a table containing information about CPU cache devices. | |
| ciCacheInfo | 1.3.6.1.4.1.1050.25.4.55.54.1 | not-accessible | This entry shows information about each CPU cache device. | |
| STR ciSocketDesignation | 1.3.6.1.4.1.1050.25.4.55.54.1.1 | DisplayString | read-only | This entry shows the cache socket designation labels on top of the base board. |
| INT ciCacheConfiguration | 1.3.6.1.4.1.1050.25.4.55.54.1.2 | INTEGER | read-only | This entry shows the configuration of this cache module. Bits 15:10 - Reserved, must be 0 Bits 9:8 - Operational Mode: 00b - Write through 01b - Write back 10b - Varies with memory address 11b - Unknown Bit 7 - Enabled/Disabled 1b - Enabled 0b - Disabled Bits 6:5 - Location 00b - Internal 01b - External 10b - Reserved 11b - Unknown Bit 4 - Reserved Bit 3 - Cache Socketed 1b - Socketed 0b - Not socketed Bits 2:0 - Cache Level |
| INT ciMaximumCacheSize | 1.3.6.1.4.1.1050.25.4.55.54.1.3 | INTEGER | read-only | This entry shows the maximum cache size that can be installed. Bits 14:0 : Max. size in given granularity Bit 15 Granularity : 0 = 1K granularity 1 = 64K granularity |
| INT ciInstalledSize | 1.3.6.1.4.1.1050.25.4.55.54.1.4 | INTEGER | read-only | This entry shows the installed cache size. Bits 14:0 : Max. size in given granularity Bit 15 Granularity : 0 = 1K granularity 1 = 64K granularity |
| INT ciSupportedSRAMType | 1.3.6.1.4.1.1050.25.4.55.54.1.5 | INTEGER | read-only | This entry shows the supported SRAM type. Bit 0 - Other Bit 1 - Unknown Bit 2 - Nonburst Bit 3 - Burst Bit 4 - Pipeline Burst Bit 5 - Synchronous Bit 6 - Asynchronous Bits7:15 Reserved |
| INT ciCurrentSRAMType | 1.3.6.1.4.1.1050.25.4.55.54.1.6 | INTEGER | read-only | This entry shows the current SRAM type. Bit 0 - Other Bit 1 - Unknown Bit 2 - Nonburst Bit 3 - Burst Bit 4 - Pipeline Burst Bit 5 - Synchronous Bit 6 - Asynchronous Bits7:15 Reserved |
| pcPortConnectorInfoTable | 1.3.6.1.4.1.1050.25.4.55.55 | not-accessible | This entry is a table containing information about all port connectors. | |
| pcPortConnectorInfo | 1.3.6.1.4.1.1050.25.4.55.55.1 | not-accessible | This entry shows information about each port connector. | |
| STR pcInternalReferenceDesignator | 1.3.6.1.4.1.1050.25.4.55.55.1.1 | DisplayString | read-only | This entry shows the internal reference designation labels on top of the base board. |
| INT pcInternalConnectorType | 1.3.6.1.4.1.1050.25.4.55.55.1.2 | INTEGER | read-only | This entry shows the internal connector type. 00h - None 01h - Centronics 02h - Mini Centronics 03h - Proprietary 04h - DB25 pin male 05h - DB25 pin female 06h - DB15 pin male 07h - DB15 pin female 08h - DB9 pin male 09h - DB9 pin female 0Ah - RJ-11 0Bh - RJ-45 0Ch - 50 pin Mini SCSI 0Dh - Mini DIN 0Eh - Micro DIN 0Fh - PS/2 10h - Infrared 11h - HP-HIL 12h - Access BUS 13h - SSA SCSI 14h - Circular DIN-8 male 15h - Circular DIN-8 female 16h - On board IDE 17h - On board floppy 18h - 9 pin dual Inline 19h - 25 pin dual Inline 1Ah - 50 pin dual Inline 1Bh - 68 pin dual Inline 1Ch - On board sound input for CD-ROM 1Dh - Mini Centronics Type 14 1Eh - Mini Centronics Type 26 A0h - PC98 A1h - PC98 Hireso A2h - PC H98 A3h - PC98 Note A4h - PC 98 Full FFh - Other |
| STR pcExternalReferenceDesignator | 1.3.6.1.4.1.1050.25.4.55.55.1.3 | DisplayString | read-only | This entry shows the external reference designation labels on top of the base board. |
| INT pcExternalConnectorType | 1.3.6.1.4.1.1050.25.4.55.55.1.4 | INTEGER | read-only | This entry shows the external connector type. 00h - None 01h - Centronics 02h - Mini Centronics 03h - Proprietary 04h - DB25 pin male 05h - DB25 pin female 06h - DB15 pin male 07h - DB15 pin female 08h - DB9 pin male 09h - DB9 pin female 0Ah - RJ-11 0Bh - RJ-45 0Ch - 50 pin Mini SCSI 0Dh - Mini DIN 0Eh - Micro DIN 0Fh - PS/2 10h - Infrared 11h - HP-HIL 12h - Access BUS 13h - SSA SCSI 14h - Circular DIN-8 male 15h - Circular DIN-8 female 16h - On board IDE 17h - On board floppy 18h - 9 pin dual Inline 19h - 25 pin dual Inline 1Ah - 50 pin dual Inline 1Bh - 68 pin dual Inline 1Ch - On board sound input for CD-ROM 1Dh - Mini Centronics Type 14 1Eh - Mini Centronics Type 26 A0h - PC98 A1h - PC98 Hireso A2h - PC H98 A3h - PC98 Note A4h - PC98 Full FFh - Other |
| INT pcPortType | 1.3.6.1.4.1.1050.25.4.55.55.1.5 | INTEGER | read-only | This entry shows the port type 00h - None 01h - Parallel Port XT/AT Compatible 02h - Parallel Port PS/2 03h - Parallel Port ECP 04h - Parallel Port EPP 05h - Parallel Port ECP/EPP 06h - Serial Port XT/AT Compatible 07h - Serial Port 16450 Compatible 08h - Serial Port 16650 Compatible 09h - Serial Port 16650A Compatible 0Ah - SCSI Port 0Bh - MIDI Port 0Ch - Joy stick port 0Dh - Keyboard Port 0Eh - Mouse Port 0Fh - SSA SCSI 10h - USB 11h - FireWire 12h - PCMCIA Type I 13h - PCMCIA Type II 14h - PCMCIA Type III 15h - Cardbus 16h - Access Bus Port 17h - SCSI II 18h - SCSI Wide 19h - PC-98 1Ah - PC-98 Hireso 1Bh - OC-H98 A0h - 8251 Compatible A1h - 8251 FIFO Compatible FFh - Other |
| ssSystemSlotInfoTable | 1.3.6.1.4.1.1050.25.4.55.56 | not-accessible | This entry is a table containing information about all system slots. | |
| ssSystemSlotInfo | 1.3.6.1.4.1.1050.25.4.55.56.1 | not-accessible | This entry shows information about each system slot. | |
| STR ssSlotDesignation | 1.3.6.1.4.1.1050.25.4.55.56.1.1 | DisplayString | read-only | This entry shows the slot designation label on top of the base board. |
| INT ssSlotType | 1.3.6.1.4.1.1050.25.4.55.56.1.2 | INTEGER | read-only | This entry shows the slot type. 01h - Other 02h - Unknown 03h - ISA 04h - MCA 05h - EISA 06h - PCI 07h - PCMCIA 08h - VL VESA 09h - Proprietary 0Ah - Processor Card Slot 0Bh - Proprietary Memory Card 0Ch - I/O Riser Card Slot 0Dh - NuBus 0Eh - PCI- 66MHz Capable A0h - PC98/C20 A1h - PC98/C24 A2h - PC98/E A3h - PC98/Local Bus A4h - PC98/Card |
| INT ssSlotDataBusWidth | 1.3.6.1.4.1.1050.25.4.55.56.1.3 | INTEGER | read-only | This entry shows the width of the data bus. 01h - Other 02h - Unknown 03h - 8bit 04h - 16bit 05h - 32bit 06h - 64bit 07h - 128bit |
| INT ssCurrentUsage | 1.3.6.1.4.1.1050.25.4.55.56.1.4 | INTEGER | read-only | This entry shows the current usage of this slot. 01h - Other 02h - Unknown 03h - Available 04h - In use |
| INT ssSlotLength | 1.3.6.1.4.1.1050.25.4.55.56.1.5 | INTEGER | read-only | This entry shows the length of the slot. 01h - Other 02h - Unknown 03h - Half Length 04h - Full Length |
| INT ssSlotID | 1.3.6.1.4.1.1050.25.4.55.56.1.6 | INTEGER | read-only | This entry shows the slot ID. MCA - Logical Micro Channel slot number EISA - Logical EISA slot number PCI - The value present in the slot number field of the PCI interrupt routing table entry that is associated with the slot. PCMCIA- Identifies the adapter number and socket number to be passed to PCMCIA socket services to identify this slot. |
| INT ssSlotCharacteristics | 1.3.6.1.4.1.1050.25.4.55.56.1.7 | INTEGER | read-only | This entry shows the characteristics of this slot. Bit 0 - Unknown Bit 1 - Provide 5.0 Volts Bit 2 - Provide 3.3 Volts Bit 1 - Slot's opening is shared with another slot, e.g. PCI/EISA shared slot Bits 4:7 - Reserved |
| obOnBoardDeviceInfoTable | 1.3.6.1.4.1.1050.25.4.55.57 | not-accessible | This entry is a table containing information about all on board devices. | |
| obOnBoardDeviceInfo | 1.3.6.1.4.1.1050.25.4.55.57.1 | not-accessible | This entry shows information about each on board device. | |
| INT obDeviceType | 1.3.6.1.4.1.1050.25.4.55.57.1.1 | INTEGER | read-only | This entry shows the device type. 01H - Other 02H - Unknown 03H - Video 04H - SCSI 05H - Ethernet 06H - Token Ring 07H - Sound |
| STR obDescription | 1.3.6.1.4.1.1050.25.4.55.57.1.2 | DisplayString | read-only | This entry shows the description of the on board device. |
| oemStringTable | 1.3.6.1.4.1.1050.25.4.55.58 | not-accessible | This entry is a table showing OEM defined strings. | |
| oemStrings | 1.3.6.1.4.1.1050.25.4.55.58.1 | not-accessible | This entry shows information about each OEM string. | |
| STR oemString | 1.3.6.1.4.1.1050.25.4.55.58.1.1 | DisplayString | read-only | This entry is an individual OEM string. |
| smEventLogTable | 1.3.6.1.4.1.1050.25.4.55.59 | not-accessible | This entry is a table of event log entries. | |
| smEventLogEntry | 1.3.6.1.4.1.1050.25.4.55.59.1 | not-accessible | This entry contains information about each logged event. | |
| STR smLogTime | 1.3.6.1.4.1.1050.25.4.55.59.1.1 | DisplayString | read-only | This entry shows the event log time. |
| INT smLogType | 1.3.6.1.4.1.1050.25.4.55.59.1.2 | INTEGER | read-only | This entry shows the event log type. |
| STR smLogDescription | 1.3.6.1.4.1.1050.25.4.55.59.1.3 | DisplayString | read-only | This entry shows the event log description. |
| INT numberOfIPAddress | 1.3.6.1.4.1.1050.25.4.56 | INTEGER | read-only | This entry shows the number of IP addresses assigned to this server. |
| ipAddressTable | 1.3.6.1.4.1.1050.25.4.57 | not-accessible | This entry is a table showing the IP addresses assigned to this server. | |
| ipAddresses | 1.3.6.1.4.1.1050.25.4.57.1 | not-accessible | This entry shows information about each IP address assigned to this server. | |
| IP ipAddress | 1.3.6.1.4.1.1050.25.4.57.1.1 | IpAddress | read-only | This entry is the individual IP address assigned to this server. |
| OCT ipxAddress | 1.3.6.1.4.1.1050.25.4.58 | OCTET STRING | read-only | This entry is the internal IPX address assigned to this server. |
| INT numberOfLoginUser | 1.3.6.1.4.1.1050.25.4.59 | INTEGER | read-only | This field shows the number of entries in the loginUserTable. |
| loginUserTable | 1.3.6.1.4.1.1050.25.4.60 | not-accessible | This entry is a table containing information about all logged in users. | |
| loginUser | 1.3.6.1.4.1.1050.25.4.60.1 | not-accessible | This entry shows information about each logged in user. | |
| STR loginUserName | 1.3.6.1.4.1.1050.25.4.60.1.1 | DisplayString | read-only | This entry shows the logged in user's name. |
| STR loginTime | 1.3.6.1.4.1.1050.25.4.60.1.2 | DisplayString | read-only | This entry shows the user's login time. |
| INT numberOfDriverLoaded | 1.3.6.1.4.1.1050.25.4.61 | INTEGER | read-only | This field shows the number of entries in the driverLoadedTable. |
| driverLoadedTable | 1.3.6.1.4.1.1050.25.4.62 | not-accessible | This entry is a table containing information about all software (including drivers) currently running on the server. | |
| driverLoaded | 1.3.6.1.4.1.1050.25.4.62.1 | not-accessible | This entry contains information about each software running on the server. | |
| STR driverName | 1.3.6.1.4.1.1050.25.4.62.1.1 | DisplayString | read-only | This entry shows the name of the software running on the server. |
| STR driverDescription | 1.3.6.1.4.1.1050.25.4.62.1.2 | DisplayString | read-only | This entry shows a description of the software running on the server. |
| performance | 1.3.6.1.4.1.1050.25.4.63 | |||
| INT numberOfPageIn | 1.3.6.1.4.1.1050.25.4.63.1 | INTEGER | read-only | This entry shows the number of page-ins during the last sampling. |
| INT byteOfPageIn | 1.3.6.1.4.1.1050.25.4.63.2 | INTEGER | read-only | This entry shows the number of page-in bytes during the last sampling. |
| INT numberOfPageOut | 1.3.6.1.4.1.1050.25.4.63.3 | INTEGER | read-only | This entry shows the number of page-out during the last sampling. |
| INT byteOfPageOut | 1.3.6.1.4.1.1050.25.4.63.4 | INTEGER | read-only | This entry shows the number of page-out bytes during the last sampling. |
| INT numberOfPageFault | 1.3.6.1.4.1.1050.25.4.63.5 | INTEGER | read-only | This entry shows the total number of page-faults during the last sampling. |
| INT diskCacheReadHitRatio | 1.3.6.1.4.1.1050.25.4.63.6 | INTEGER | read-only | This entry shows the ratio of disk cache read hits in the last sampling. |
| INT diskCacheWriteHitRatio | 1.3.6.1.4.1.1050.25.4.63.7 | INTEGER | read-only | This entry shows the ratio of disk cache write hits in the last sampling |
| INT numberOfFreeMem | 1.3.6.1.4.1.1050.25.4.63.8 | INTEGER | read-only | This entry shows the number of 4KB pages available to user processes |
| INT numberOfTotalSwap | 1.3.6.1.4.1.1050.25.4.63.9 | INTEGER | read-only | This entry shows the total number of physical disk (512-byte) blocks available for swapping and paging |
| INT numberOfFreeSwap | 1.3.6.1.4.1.1050.25.4.63.10 | INTEGER | read-only | This entry shows the free number of physical disk (512-byte) blocks available for swapping and paging |
| INT numberOfSwapIn | 1.3.6.1.4.1.1050.25.4.63.11 | INTEGER | read-only | This entry shows the number of transfers from swap into memory per second |
| INT numberOfSwapInPages | 1.3.6.1.4.1.1050.25.4.63.12 | INTEGER | read-only | This entry shows the number of 4KB pages transfers from swap into memory per second |
| INT numberOfSwapOut | 1.3.6.1.4.1.1050.25.4.63.13 | INTEGER | read-only | This entry shows the number of transfers from memory into swap per second. If this value is greater than zero, you may need to increase the amount of memory or reduce the number of buffers. |
| INT numberOfSwapOutPages | 1.3.6.1.4.1.1050.25.4.63.14 | INTEGER | read-only | This entry shows the number of 4KB pages transfers from memory into swap per second |
| INT numberOfContextSwitch | 1.3.6.1.4.1.1050.25.4.63.15 | INTEGER | read-only | This entry shows the number of context switch per second |
| ntPerf | 1.3.6.1.4.1.1050.25.4.65 | |||
| systemPerf | 1.3.6.1.4.1.1050.25.4.65.1 | |||
| GAU processorTime | 1.3.6.1.4.1.1050.25.4.65.1.1 | Gauge | read-only | This entry is the average percentage of time all the processors on the system are busy to execute non-idle threads. |
| GAU privilegedTime | 1.3.6.1.4.1.1050.25.4.65.1.2 | Gauge | read-only | This entry is the average percentage of time spent in Privileged mode by all processors. |
| GAU userTime | 1.3.6.1.4.1.1050.25.4.65.1.3 | Gauge | read-only | This entry is the average percentage of time spent in User mode by all processors. |
| GAU interruptTime | 1.3.6.1.4.1.1050.25.4.65.1.4 | Gauge | read-only | This entry is the average percentage of the Interrupt Time of all processors. |
| INT interruptsPerSec | 1.3.6.1.4.1.1050.25.4.65.1.5 | INTEGER | read-only | This entry is the hardware interrupts received and serviced by the system per second. |
| INT contextSwitchesPerSec | 1.3.6.1.4.1.1050.25.4.65.1.6 | INTEGER | read-only | This entry is the context switches from one thread to another per second. |
| INT exceptionDispatchesPerSec | 1.3.6.1.4.1.1050.25.4.65.1.7 | INTEGER | read-only | This entry is the exceptions dispatched by the system per second. |
| INT systemCallsPerSec | 1.3.6.1.4.1.1050.25.4.65.1.8 | INTEGER | read-only | This entry is the calls to Windows NT system service routines per second. |
| INT fileControlOpsPerSec | 1.3.6.1.4.1.1050.25.4.65.1.9 | INTEGER | read-only | This entry is all file system operations that are neither reads nor writes per second. |
| INT fileControlBytesPerSec | 1.3.6.1.4.1.1050.25.4.65.1.10 | INTEGER | read-only | This entry is bytes transferred for all file system operations that are neither reads nor writes per second. |
| INT fileDataOpsPerSec | 1.3.6.1.4.1.1050.25.4.65.1.11 | INTEGER | read-only | This entry is the read and write operations to file system devices per second. |
| INT fileReadOpsPerSec | 1.3.6.1.4.1.1050.25.4.65.1.12 | INTEGER | read-only | This entry is the read operations of all the file system per second. |
| INT fileWriteOpsPerSec | 1.3.6.1.4.1.1050.25.4.65.1.13 | INTEGER | read-only | This entry is the number of write operations of all the file system per second. |
| INT fileReadBytesPerSec | 1.3.6.1.4.1.1050.25.4.65.1.14 | INTEGER | read-only | This entry is the bytes transferred for all the file system read operations per second. |
| INT fileWriteBytesPerSec | 1.3.6.1.4.1.1050.25.4.65.1.15 | INTEGER | read-only | This entry is the bytes transferred for all the file system write operations per second. |
| cachePerf | 1.3.6.1.4.1.1050.25.4.65.2 | |||
| GAU copyReadsHitRatio | 1.3.6.1.4.1.1050.25.4.65.2.1 | Gauge | read-only | This entry is the percentage of Cache Copy Read requests that hit the cache. |
| INT copyReadsPerSec | 1.3.6.1.4.1.1050.25.4.65.2.2 | INTEGER | read-only | This entry is the number of copy reads per second. |
| GAU dataMapHitRatio | 1.3.6.1.4.1.1050.25.4.65.2.3 | Gauge | read-only | This entry is the percentage of Data Maps in the cache. |
| INT dataMapsPerSec | 1.3.6.1.4.1.1050.25.4.65.2.4 | INTEGER | read-only | This entry is the frequency (per second) that a file system maps a page of a file into the cache to read the page. |
| INT dataFlushesPerSec | 1.3.6.1.4.1.1050.25.4.65.2.5 | INTEGER | read-only | This entry is the frequency (per second) that the cache has flushed its contents to disk. More than one page can be transferred on each flush operation. |
| INT dataFlushPagesPerSec | 1.3.6.1.4.1.1050.25.4.65.2.6 | INTEGER | read-only | This entry is the number of pages per second the cache has flushed to disk. More than one page can be transferred on each flush operation. |
| INT lazeWriteFlushesPerSec | 1.3.6.1.4.1.1050.25.4.65.2.7 | INTEGER | read-only | This entry is the frequency (per second) that the cache's Lazy Write thread has written to disk. More than one page can be transferred on each write operation. |
| INT lazeWritePagesPerSec | 1.3.6.1.4.1.1050.25.4.65.2.8 | INTEGER | read-only | This entry is the frequency (per second) the cache's Lazy Write thread has written to disk. More than one page can be transferred on a single disk write operation. |
| memoryPerf | 1.3.6.1.4.1.1050.25.4.65.3 | |||
| INT pageFaultsPerSec | 1.3.6.1.4.1.1050.25.4.65.3.1 | INTEGER | read-only | This entry is the number of page faults per second in the processor. |
| INT transitionFaultsPerSec | 1.3.6.1.4.1.1050.25.4.65.3.2 | INTEGER | read-only | This entry is the number of page faults resolved per second by recovering pages that were in transition. The pages were recovered without additional disk activity. |
| INT writeCopiesPerSec | 1.3.6.1.4.1.1050.25.4.65.3.3 | INTEGER | read-only | This entry is the number of page faults per second that have been satisfied by making a copy of a page when an attempt to write to the page is made. |
| INT pageReadPerSec | 1.3.6.1.4.1.1050.25.4.65.3.4 | INTEGER | read-only | This entry is the number of times the disk was read per second to retrieve pages of virtual memory necessary to resolve page faults. Multiple pages can be read during a disk read operation. |
| INT pageWritePerSec | 1.3.6.1.4.1.1050.25.4.65.3.5 | INTEGER | read-only | This entry is the number of times per second that pages have been written to the disk. Each such write operation may transfer a number of pages. |
| INT pagesInputPerSec | 1.3.6.1.4.1.1050.25.4.65.3.6 | INTEGER | read-only | This entry is the number of pages read per second from the disk to resolve memory references to pages. This counter includes paging traffic on behalf of the system cache to access file data for applications. |
| INT pagesOutputPerSec | 1.3.6.1.4.1.1050.25.4.65.3.7 | INTEGER | read-only | This entry is the number of pages written to the disk per second because the pages have been modified in main memory. |
| INT pagesPerSec | 1.3.6.1.4.1.1050.25.4.65.3.8 | INTEGER | read-only | This entry is the number of pages read from or written to the disk per second to resolve memory references to pages that were not in memory. |
| INT systemCodeBytes | 1.3.6.1.4.1.1050.25.4.65.3.9 | INTEGER | read-only | This entry is the number of pagable bytes of System Code Total Bytes currently resident in core memory. There is another ~300k bytes of non-paged kernel code. |
| INT systemDriverBytes | 1.3.6.1.4.1.1050.25.4.65.3.10 | INTEGER | read-only | This entry is the number of pagable bytes of System Driver Total Bytes currently resident in core memory. There is another ~700k bytes of non-paged driver code. |
| physicalDiskPerfTbl | 1.3.6.1.4.1.1050.25.4.65.5 | not-accessible | This entry is a table containing the performance counters of physical disk drives. | |
| physicalDiskPerf | 1.3.6.1.4.1.1050.25.4.65.5.1 | not-accessible | This entry contains information about each performance counter of a physical disk drive. | |
| INT physicalDiskId | 1.3.6.1.4.1.1050.25.4.65.5.1.1 | INTEGER | read-only | This entry is the index for physical disk drives starting from 1. A 0 value will report an average value of all physical disk drives. |
| INT avgBytesPerRead | 1.3.6.1.4.1.1050.25.4.65.5.1.2 | INTEGER | read-only | This entry is the average number of bytes transferred from the disk during read operations. |
| INT avgBytesPerWrite | 1.3.6.1.4.1.1050.25.4.65.5.1.3 | INTEGER | read-only | This entry is the average number of bytes transferred to the disk during write operations. |
| INT avgBytesPerTransfer | 1.3.6.1.4.1.1050.25.4.65.5.1.4 | INTEGER | read-only | This entry is the average number of bytes transferred to or from the disk during write or read operations. |
| INT avgSecPerRead | 1.3.6.1.4.1.1050.25.4.65.5.1.5 | INTEGER | read-only | This entry is the average time in seconds of a read of data from the disk. |
| INT avgSecPerWrite | 1.3.6.1.4.1.1050.25.4.65.5.1.6 | INTEGER | read-only | This entry is the average time in seconds of a write of data to the disk. |
| INT avgSecPerTransfer | 1.3.6.1.4.1.1050.25.4.65.5.1.7 | INTEGER | read-only | This entry is the time in seconds of the average disk transfer. |
| INT diskReadBytesPerSec | 1.3.6.1.4.1.1050.25.4.65.5.1.8 | INTEGER | read-only | This entry is the number of bytes transferred from the disk during read operations per second. |
| INT diskWriteBytesPerSec | 1.3.6.1.4.1.1050.25.4.65.5.1.9 | INTEGER | read-only | This entry is the number of bytes transferred to the disk during write operations per second. |
| INT diskBytesPerSec | 1.3.6.1.4.1.1050.25.4.65.5.1.10 | INTEGER | read-only | This entry is the number of bytes transferred to or from the disk during write or read operations per second. |
| INT diskReadPerSec | 1.3.6.1.4.1.1050.25.4.65.5.1.11 | INTEGER | read-only | This entry is the number of read operations on the disk per second. |
| INT diskWritePerSec | 1.3.6.1.4.1.1050.25.4.65.5.1.12 | INTEGER | read-only | This entry is the number of write operations on the disk per second. |
| INT diskTransferPerSec | 1.3.6.1.4.1.1050.25.4.65.5.1.13 | INTEGER | read-only | This entry is the number of read and write operations on the disk per second. |
| logicalDiskPerfTbl | 1.3.6.1.4.1.1050.25.4.65.6 | not-accessible | This entry is a table containing the performance counters of logical disk drives. | |
| logicalDiskPerf | 1.3.6.1.4.1.1050.25.4.65.6.1 | not-accessible | This entry contains information about each performance counter of a logical disk drive. | |
| INT logicalDiskId | 1.3.6.1.4.1.1050.25.4.65.6.1.1 | INTEGER | read-only | This entry is the index for logical disk drives starting from 1. A 0 value will report an average value of all physical disk drives. |
| INT lavgBytesPerRead | 1.3.6.1.4.1.1050.25.4.65.6.1.2 | INTEGER | read-only | This entry is the average number of bytes transferred from the disk during read operations. |
| INT lavgBytesPerWrite | 1.3.6.1.4.1.1050.25.4.65.6.1.3 | INTEGER | read-only | This entry is the average number of bytes transferred to the disk during write operations. |
| INT lavgBytesPerTransfer | 1.3.6.1.4.1.1050.25.4.65.6.1.4 | INTEGER | read-only | This entry is the average number of bytes transferred to or from the disk during write or read operations. |
| INT lavgSecPerRead | 1.3.6.1.4.1.1050.25.4.65.6.1.5 | INTEGER | read-only | This entry is the average time in seconds of a read of data from the disk. |
| INT lavgSecPerWrite | 1.3.6.1.4.1.1050.25.4.65.6.1.6 | INTEGER | read-only | This entry is the average time in seconds of a write of data to the disk. |
| INT lavgSecPerTransfer | 1.3.6.1.4.1.1050.25.4.65.6.1.7 | INTEGER | read-only | This entry is the time in seconds of the average disk transfer. |
| INT ldiskReadBytesPerSec | 1.3.6.1.4.1.1050.25.4.65.6.1.8 | INTEGER | read-only | This entry is the number of bytes transferred from the disk during read operations per second. |
| INT ldiskWriteBytesPerSec | 1.3.6.1.4.1.1050.25.4.65.6.1.9 | INTEGER | read-only | This entry is the number of bytes transferred to the disk during write operations per second. |
| INT ldiskBytesPerSec | 1.3.6.1.4.1.1050.25.4.65.6.1.10 | INTEGER | read-only | This entry is the number of bytes transferred to or from the disk during write or read operations per second. |
| INT ldiskReadPerSec | 1.3.6.1.4.1.1050.25.4.65.6.1.11 | INTEGER | read-only | This entry is the number of read operations on the disk per second. |
| INT ldiskWritePerSec | 1.3.6.1.4.1.1050.25.4.65.6.1.12 | INTEGER | read-only | This entry is the number of write operations on the disk per second. |
| INT ldiskTransferPerSec | 1.3.6.1.4.1.1050.25.4.65.6.1.13 | INTEGER | read-only | This entry is the number of read and write operations on the disk per second. |
| STR serverLocalTime | 1.3.6.1.4.1.1050.25.4.66 | DisplayString | read-only | This field shows the real local time on each server. |
| asmsystem | 1.3.6.1.4.1.1050.25.5 | |||
| INT osType | 1.3.6.1.4.1.1050.25.5.1 | INTEGER | read-only | This entry displays the server's operating system: 0 = NetWare 1 = SCO UNIX 2 = Windows NT 3 = UnixWare |
| INT asmHardware | 1.3.6.1.4.1.1050.25.5.2 | INTEGER | read-only | This shows whether or not the system supports ASM proprietary hardware: 0 = NO 1 = YES |
| INT asmDmiVersion | 1.3.6.1.4.1.1050.25.5.3 | INTEGER | read-only | This entry shows the Acer DMI BIOS version number: 0 = not supported 110 = version 1.1 200 = version 2.0 |
| asmHW | 1.3.6.1.4.1.1050.25.5.4 | |||
| INT numberOfFans | 1.3.6.1.4.1.1050.25.5.4.1 | INTEGER | read-only | This entry shows the number of fans installed. |
| INT numberOfThermometers | 1.3.6.1.4.1.1050.25.5.4.2 | INTEGER | read-only | This entry shows the number of system thermometers installed. |
| INT numberOfVoltages | 1.3.6.1.4.1.1050.25.5.4.3 | INTEGER | read-only | This entry shows the number of voltage sensors installed. |
| INT numberOfBusCounters | 1.3.6.1.4.1.1050.25.5.4.4 | INTEGER | read-only | This entry shows the number of bus utilization counters. |
| INT asmUPS | 1.3.6.1.4.1.1050.25.5.4.5 | INTEGER | read-only | This entry shows the UPS device condition: 1 = server with UPS device 0 = server without UPS device |
| INT chassisIntrusion | 1.3.6.1.4.1.1050.25.5.4.7 | INTEGER | read-only | The status of chassis intrusion: -1 = Not supported, 0 = normal, 1 = abnormal. |
| INT fuseStatus | 1.3.6.1.4.1.1050.25.5.4.8 | INTEGER | read-only | This entry displays the status of fuses. Each bit indicates separate status of one fuse, 1 is failed, 0 is noraml. If system has no fuse at all, the entry shows -1. bit0: Keyboard/Mouse fuse bit1: USB1 fuse bit2: USB2 fuse bit3: SCSI1 fuse bit4: SCSI2 fuse |
| INT redundantPowerSupplyStatus | 1.3.6.1.4.1.1050.25.5.4.9 | INTEGER | read-only | This entry displays the status of redundant power subsystem. If system has no such equipment installed, bit31 of this value will be set to 1. Bit 0: power supply 1 status, 1=OK Bit 1: power supply 2 status, 1=OK Bit 2: power supply 1 fan status, 1=OK Bit 3: power supply 2 fan status, 1=OK Bit 4: power supply 1 present, 1=YES Bit 5: power supply 2 present, 1=YES |
| INT numberOfCpuSlot | 1.3.6.1.4.1.1050.25.5.4.10 | INTEGER | read-only | This entry shows the number of CPU slots: 0 = unknown 1-8 = number of CPU slots. |
| fanTable | 1.3.6.1.4.1.1050.25.5.4.11 | not-accessible | This entry is a table containing information about all fans. | |
| fanInfo | 1.3.6.1.4.1.1050.25.5.4.11.1 | not-accessible | This entry contains information about each fan. | |
| STR fanLocation | 1.3.6.1.4.1.1050.25.5.4.11.1.1 | DisplayString | read-only | This entry shows the fan's location in the server system, e.g. 'CPU1', 'CPU2' or 'HOUSING'. |
| INT fanStatus | 1.3.6.1.4.1.1050.25.5.4.11.1.2 | INTEGER | read-only | This entry displays the fan's working status: 0=normal 1=abnormal. When the fan is not rotating or is not installed, the status will be considered abnormal. |
| INT fanRPM | 1.3.6.1.4.1.1050.25.5.4.11.1.3 | INTEGER | read-only | This entry displays the fan's rotation speed in RPM. If the fan doesn't provide RPM information, the value will be -1. |
| thermometerTable | 1.3.6.1.4.1.1050.25.5.4.12 | not-accessible | This entry is a table containing information about all system thermometers installed. | |
| thermometerInfo | 1.3.6.1.4.1.1050.25.5.4.12.1 | not-accessible | This entry contains information about each thermometer. | |
| STR thermometerLocation | 1.3.6.1.4.1.1050.25.5.4.12.1.1 | DisplayString | read-only | This entry shows the thermometer's location in the server system, e.g. 'CPU1', 'CPU2' or 'SYSTEM'. |
| INT thermometerDegree | 1.3.6.1.4.1.1050.25.5.4.12.1.2 | INTEGER | read-only | This entry displays the thermometer reading. Values displayed have to be divided by ten (10) to show the temperature in degrees Celsius. For example, a reading of 305 means that the temperature is at 30.5 degrees Celsius. |
| voltageTable | 1.3.6.1.4.1.1050.25.5.4.13 | not-accessible | This entry is a table containing information about all voltage sensors installed. | |
| voltageInfo | 1.3.6.1.4.1.1050.25.5.4.13.1 | not-accessible | This entry contains information about each voltage sensor. | |
| STR voltageLocation | 1.3.6.1.4.1.1050.25.5.4.13.1.1 | DisplayString | read-only | This entry shows the voltage sensor's location in the server system, e.g. 'CPU1', 'CPU2' or 'SYSTEM'. |
| INT currentVoltage | 1.3.6.1.4.1.1050.25.5.4.13.1.2 | INTEGER | read-only | This entry displays the current voltage reading in milli-volts. |
| INT validVoltage | 1.3.6.1.4.1.1050.25.5.4.13.1.3 | INTEGER | read-only | This entry displays the ideal voltage reading in milli-volts. |
| INT maxVoltage | 1.3.6.1.4.1.1050.25.5.4.13.1.4 | INTEGER | read-only | This entry displays the maximum safe operating voltage in milli-volts. If the voltage goes above this value, the system may not work properly. |
| INT minVoltage | 1.3.6.1.4.1.1050.25.5.4.13.1.5 | INTEGER | read-only | This entry displays the minimum safe operating voltage in milli-volts. If the voltage goes below this value, the system may not work properly. |
| busCounterTable | 1.3.6.1.4.1.1050.25.5.4.14 | not-accessible | This entry is a table containing information about all bus utilization counters installed. | |
| busCounterInfo | 1.3.6.1.4.1.1050.25.5.4.14.1 | not-accessible | This entry contains information about each bus utilization counter. | |
| STR busCounterLocation | 1.3.6.1.4.1.1050.25.5.4.14.1.1 | DisplayString | read-only | The system bus monitored by the counter e.g. 'PCI1', 'PCI2', 'EISA1' or 'EISA2'. |
| INT busUtilization | 1.3.6.1.4.1.1050.25.5.4.14.1.2 | INTEGER | read-only | This entry displays the bus utilization. Values displayed have to be divided by one hundred (100) to show the percentage of bus utilization. For example, a reading of 1234 means that bus utilization is at 12.34%. |
| asmUPSInfo | 1.3.6.1.4.1.1050.25.5.4.15 | |||
| INT upsPower1Exist | 1.3.6.1.4.1.1050.25.5.4.15.1 | INTEGER | read-only | This entry shows the power supply condition: 1 = power supply #1 exists 0 = power supply #1 doesn't exist. |
| INT upsPower2Exist | 1.3.6.1.4.1.1050.25.5.4.15.2 | INTEGER | read-only | This entry shows the power supply condition: 1 = power supply #2 exists 0 = power supply #2 doesn't exist. |
| INT upsPower3Exist | 1.3.6.1.4.1.1050.25.5.4.15.3 | INTEGER | read-only | This entry shows the power supply condition: 1 = power supply #3 exists 0 = power supply #3 doesn't exist. |
| INT upsPower1Status | 1.3.6.1.4.1.1050.25.5.4.15.4 | INTEGER | read-only | This entry shows the power supply condition: 0 = power supply #1 is abnormal 1 = power supply #1 is normal. |
| INT upsPower2Status | 1.3.6.1.4.1.1050.25.5.4.15.5 | INTEGER | read-only | This entry shows the power supply condition: 0 = power supply #2 is abnormal 1 = power supply #2 is normal. |
| INT upsPower3Status | 1.3.6.1.4.1.1050.25.5.4.15.6 | INTEGER | read-only | This entry shows the power supply condition: 0 = power supply #3 is abnormal 1 = power supply #3 is normal. |
| INT upsBatteryExist | 1.3.6.1.4.1.1050.25.5.4.15.7 | INTEGER | read-only | This entry shows the battery condition: 1 = battery exists 0 = battery doesn't exist. |
| INT upsBatteryStatus | 1.3.6.1.4.1.1050.25.5.4.15.8 | INTEGER | read-only | This entry shows the power supply condition: 0 = power supply #3 is abnormal 1 = power supply #3 is normal. |
| INT upsACStatus | 1.3.6.1.4.1.1050.25.5.4.15.9 | INTEGER | read-only | This entry shows the AC power condition: 0 = AC power is abnormal 1 = AC power is normal. |
| INT upsFanStatus | 1.3.6.1.4.1.1050.25.5.4.15.10 | INTEGER | read-only | This entry shows the fan condition: 0 = power ups fan is abnormal 1 = power ups fan is normal. |
| INT cpuSlotStatus | 1.3.6.1.4.1.1050.25.5.4.17 | INTEGER | read-only | This entry is partitioned into nibbles, each shows status of one CPU slot: bit0: CPU is present bit1: CPU is enabled bit2: CPU error (IERR#, Thermtrip# issued). |
| INT asmAgentVersion | 1.3.6.1.4.1.1050.25.5.5 | INTEGER | read-only | This entry shows the ASM Agent version number: 120 = version 1.2, 200 = version 2.0, etc. |
| INT passwordProtected | 1.3.6.1.4.1.1050.25.5.6 | INTEGER | read-only | This entry shows if the ASM Agent requires password for SNMP Set: 1 = YES 0 = NO |
| INT numberOfTrapTargets | 1.3.6.1.4.1.1050.25.5.7 | INTEGER | read-only | This entry shows the number of targets of SNMP Trap. |
| trapTargetTable | 1.3.6.1.4.1.1050.25.5.8 | not-accessible | This entry is a table containing information about all trap targets. | |
| trapTargetInfo | 1.3.6.1.4.1.1050.25.5.8.1 | not-accessible | This entry contains information about each trap target. Index starts at 0. | |
| STR targetAddress | 1.3.6.1.4.1.1050.25.5.8.1.1 | DisplayString | read-only | This entry shows the trap target's IP/IPX address in ASCII format. For example, 00ABCDEF:000000000001 for IPX 192.9.210.99 for IP |
| RDM rdmStatus | 1.3.6.1.4.1.1050.25.5.9 | RdmStatus | read-only | This entry shows the status of RDM daughter board. |
| OCT healthStatus | 1.3.6.1.4.1.1050.25.5.10 | OCTET STRING | read-only | This entry shows the health status of system. Each bit indicates one health index |
| INT fileTransferPortTCP | 1.3.6.1.4.1.1050.25.5.11 | INTEGER | read-only | TCP port of FTU deamon. -1=N/A |
| INT fileTransferPortIPX | 1.3.6.1.4.1.1050.25.5.12 | INTEGER | read-only | IPX port of FTU deamon. -1=N/A |
| INT fileCommand | 1.3.6.1.4.1.1050.25.5.13 | INTEGER | write-only | 0 : Clear Event Log 1 : Update Asset Log 2 : Clear Statistics Log 3 : Start Statistics recording 4 : Stop Statistics recording |
| INT disableEventHandling | 1.3.6.1.4.1.1050.25.5.14 | INTEGER | read-write | If this object is set to non-zero, Agent won't handle any event and runs quietly. |
| asmalarm | 1.3.6.1.4.1.1050.25.7 | |||
| STR trapDescription | 1.3.6.1.4.1.1050.25.7.1 | DisplayString | read-only | This entry contains information about the last trap sent. |
| eventNotificationTable | 1.3.6.1.4.1.1050.25.7.2 | not-accessible | This entry is a table containing all event notification settings. | |
| eventNotification | 1.3.6.1.4.1.1050.25.7.2.1 | not-accessible | This entry contains information about each event notification setting. | |
| INT asmEventType | 1.3.6.1.4.1.1050.25.7.2.1.1 | INTEGER | read-only | This entry shows the event type: 1 : Temperature Warning 2 : Temperature Critical 3 : ECC Memory 1-Bit-Error 4 : ECC Memory Multiple-Bit-Error 5 : Fan Stops 6 : Voltage Exceeds Safe Range 7 : CPU Utilization High 8 : BUS Utilization High 9 : Memory Utilization High 10: Volume or File System Utilization High 11: NIC Counters High |
| INT eventAction | 1.3.6.1.4.1.1050.25.7.2.1.2 | INTEGER | read-write | This entry describes the actions to be taken by the agent or station when a particular event occurs. Station Side: Bit 0 : Audio Alarm Bit 1 : Flash Title Bar Bit 2 : Warning Dialog Box Bit 3 : Pager Agent Side: Bit 16: Broadcasting a message to all login users Bit 17: Shutdown the server automatically. File system will first be flushed. Bit 19: Launch a user defined program |
| STR eventProgram | 1.3.6.1.4.1.1050.25.7.2.1.3 | DisplayString | read-write | This entry shows the command string used to launch a user defined program. |
| STR eventPager | 1.3.6.1.4.1.1050.25.7.2.1.4 | DisplayString | read-write | This entry shows the pager string including telephone number and pager code. |
RFC description
Acer server storage, NIC, system board, and environmental monitoring.
Start monitoring Acer/Fujitsu Siemens server management (ASM) hardware (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.