All MIBs › AC-PSTN-MIB
Organization: AudioCodes Ltd
Last Updated: 2009-09-30
Category: Telephony and VoIP, Vendor: AudioCodes
Description: Manages PSTN (ISDN PRI/BRI and CAS) trunk interface configuration on AudioCodes media gateways, including signaling protocol selection and channel grouping.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is AC-PSTN-MIB?
This MIB manages PSTN trunk interface configuration -- ISDN PRI/BRI and CAS signaling -- on AudioCodes media gateways, devices that interconnect VoIP networks with the traditional telephone network. It centers on configuring signaling protocol selection and channel grouping for PSTN trunks, defining how digital trunk lines are set up on the gateway. Though no sample objects were provided, PSTN trunk MIBs of this kind typically also expose trunk/channel operational status, so this module likely lets an operator confirm whether configured trunks and their B-channels are in service, essential for detecting a failed span or signaling link. It would typically complement companion AudioCodes MIBs (such as AC-V5-MIB for V5 access signaling) for a full gateway status picture. It's deployed on AudioCodes media gateways providing TDM-to-VoIP interworking at a carrier or enterprise PSTN handoff point. Network engineers evaluating or troubleshooting this functionality can download the AC-PSTN-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in AC-PSTN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- AudioCodes media gateways
Monitoring Examples
No sample object names were provided for this module, so specific OID-level detail can't be given; in general, an admin managing such a gateway would configure and check the signaling protocol (PRI/BRI/CAS) and channel-group assignment per trunk, and would monitor trunk/channel status to detect a down span or D-channel signaling failure affecting call setup.
What Can Be Monitored
- PSTN trunk signaling protocol
- channel group assignment
- trunk/channel status (if exposed)
This MIB depends on
Related MIBs
Imported Objects
From AUDIOCODES-TYPES-MIB
| acBoardMibs | OBJECT-IDENTITY |
| acGeneric | OBJECT-IDENTITY |
| acProducts | OBJECT-IDENTITY |
| acRegistrations | OBJECT-IDENTITY |
| audioCodes | OBJECT-IDENTITY |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From RFC1155-SMI
| IpAddress |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 | |
| enterprises |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| RowStatus | |
| TAddress | |
| TEXTUAL-CONVENTION |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| acCasConfig | 1.3.6.1.4.1.5003.9.10.9.1.4 | |||
| INT acCasConfigEnable | 1.3.6.1.4.1.5003.9.10.9.1.4.1 | INTEGER | read-write | This parameter enables or disables the possibility CAS protocol configuration. At TP6310 When this parameter is enable the conference will disabled in case it's relevant. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: CASProtocolEnable |
| acCASFile | 1.3.6.1.4.1.5003.9.10.9.1.4.2 | |||
| acCASFileEntry | 1.3.6.1.4.1.5003.9.10.9.1.4.2.1.1 | not-accessible | ||
| U32 acCASFileIndex | 1.3.6.1.4.1.5003.9.10.9.1.4.2.1.1.1 | Unsigned32 | read-only | Cas Table Indexd. AC INI-Param: N/A |
| STR acCASFileName | 1.3.6.1.4.1.5003.9.10.9.1.4.2.1.1.2 | SnmpAdminString | read-only | This is a pointer to the CAS filename index (0-7). The index is CASFileName_X. CASFileName_0 through to CASFileName_7 are the path and names of the CAS protocol configuration files. AC INI-Param: CASFILENAME |
| acCASFileTable | 1.3.6.1.4.1.5003.9.10.9.1.4.2.1 | not-accessible | ||
| acDigitalLegs | 1.3.6.1.4.1.5003.9.10.9.2.2 | |||
| U32 acDigitalLegsBchannel | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.4 | Unsigned32 | read-only | Describes the Bchannel the Leg belong to. AC INI-Param: N/A |
| U32 acDigitalLegsCallIndex | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.2 | Unsigned32 | read-only | Decribes The Call which The Digital EndPoint Participant In It. AC INI-Param: N/A |
| U32 acDigitalLegsDSPDevice | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.10 | Unsigned32 | read-only | describes the DSP Device the Leg connected to. AC INI-Param: N/A |
| INT acDigitalLegsDTMFDetection | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.6 | INTEGER | read-only | Enables or Disables the DTMF Detection. AC INI-Param: N/A |
| INT acDigitalLegsEchoCanceller | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.5 | INTEGER | read-only | Enables or Disables the Echo Canceller. AC INI-Param: N/A |
| acDigitalLegsEntry | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1 | not-accessible | ||
| INT acDigitalLegsHighPassFilter | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.8 | INTEGER | read-only | Enables or Disables theHigh Pass Filter. AC INI-Param: N/A |
| INT acDigitalLegsInputGain | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.9 | INTEGER | read-only | Describes the Input Gain on the leg in dB. AC INI-Param: N/A |
| U32 acDigitalLegsLegIndex | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.1 | Unsigned32 | not-accessible | Decribes The Digital EndPoint In A Call. AC INI-Param: N/A |
| STR acDigitalLegsLegName | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.11 | SnmpAdminString | read-only | Describes the Leg Name as in the Control Protocol. AC INI-Param: N/A |
| acDigitalLegsTable | 1.3.6.1.4.1.5003.9.10.9.2.2.1 | not-accessible | ||
| U32 acDigitalLegsTrunk | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.3 | Unsigned32 | read-only | Describes the Trunk the Leg belong to. AC INI-Param: N/A |
| U32 acDigitalLegsVoiceVolume | 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.7 | Unsigned32 | read-only | Describs the volume of the voice in dB. AC INI-Param: N/A |
| acDS3Config | 1.3.6.1.4.1.5003.9.10.9.1.3 | |||
| INT acDS3ConfigClockSource | 1.3.6.1.4.1.5003.9.10.9.1.3.2 | INTEGER | read-write | Selects the physical DS3 framing method to be used in this board. Applicable only to the TP-2810. 0 = DS3 Clock is recovered from the line 1 = DS3 trunk clock source is provided by the board's internal clock 2 = Clock is taken from the local PLL which is not synchronized with any other clock. Access: Offline. AC INI-Param: DS3CLOCKSOURCE |
| INT acDS3ConfigFramingMethod | 1.3.6.1.4.1.5003.9.10.9.1.3.1 | INTEGER | read-write | Used to select the physical DS3 framing method to be used in this board. 0 = M23 framing 1 = C Bit Parity. Access: Offline. AC INI-Param: DS3FRAMINGMETHOD |
| INT acDS3ConfigLineBuiltOut | 1.3.6.1.4.1.5003.9.10.9.1.3.3 | INTEGER | read-write | Used to select the DS3 line build out. Applies only to the TP-2810. Access: Offline. AC INI-Param: DS3LINEBUILTOUT |
| acFiberGroupStatus | 1.3.6.1.4.1.5003.9.10.9.2.4 | |||
| U32 acFiberGroupStatusActiveLink | 1.3.6.1.4.1.5003.9.10.9.2.4.1 | Unsigned32 | read-only | Fiber group active link number. 0 - there is no active fiber group link. AC INI-Param: N/A |
| acISDNConfig | 1.3.6.1.4.1.5003.9.10.9.1.2 | |||
| acMiscISDN | 1.3.6.1.4.1.5003.9.10.9.1.2.1 | |||
| U32 acMiscISDNDuplicateQ931BuffMode | 1.3.6.1.4.1.5003.9.10.9.1.2.1.2 | Unsigned32 | read-write | Access: Offline. AC INI-Param: ISDNDUPLICATEQ931BUFFMODE |
| INT acMiscISDNQ931RelayMode | 1.3.6.1.4.1.5003.9.10.9.1.2.1.1 | INTEGER | read-write | Activates / de-activates the ISDN level 3 Q.931 Relay Mode. Choose 0 or ActivateLAPDmessaging or Q931_RELAY_TO_HOST or Layer3_IS_IUA. Access: Offline. AC INI-Param: Q931RELAYMODE |
| acPSTN | 1.3.6.1.4.1.5003.9.10.9 | |||
| acPSTNConfiguration | 1.3.6.1.4.1.5003.9.10.9.1 | |||
| acPSTNStatus | 1.3.6.1.4.1.5003.9.10.9.2 | |||
| acSDHKLMNumberingScheme | 1.3.6.1.4.1.5003.9.10.9.2.3 | |||
| acSDHKLMNumberingSchemeEntry | 1.3.6.1.4.1.5003.9.10.9.2.3.1.1 | not-accessible | ||
| acSDHKLMNumberingSchemeTable | 1.3.6.1.4.1.5003.9.10.9.2.3.1 | not-accessible | ||
| U32 acSDHKLMNumberingSchemeTrunkIndex | 1.3.6.1.4.1.5003.9.10.9.2.3.1.1.1 | Unsigned32 | not-accessible | Trunk Number. AC INI-Param: N/A |
| U32 acSDHKLMNumberingSchemeTU12OrVT15 | 1.3.6.1.4.1.5003.9.10.9.2.3.1.1.4 | Unsigned32 | read-only | AC INI-Param: N/A |
| U32 acSDHKLMNumberingSchemeTUG2OrVTG | 1.3.6.1.4.1.5003.9.10.9.2.3.1.1.3 | Unsigned32 | read-only | AC INI-Param: N/A |
| U32 acSDHKLMNumberingSchemeTUG3OrSTS1 | 1.3.6.1.4.1.5003.9.10.9.2.3.1.1.2 | Unsigned32 | read-only | AC INI-Param: N/A |
| acSonetSDH | 1.3.6.1.4.1.5003.9.10.9.1.5 | |||
| acSonetSDHEntry | 1.3.6.1.4.1.5003.9.10.9.1.5.1.1 | not-accessible | ||
| INT acSonetSDHFbrGrpAPSDirectionMode | 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.4 | INTEGER | read-write | Sets the Automatic Protection Switch Unidir/Bidir mode for the Fiber Group. Access: Offline. AC INI-Param: SDHFbrGrp_APS_DirMode |
| INT acSonetSDHFbrGrpAPSRevertMode | 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.5 | INTEGER | read-write | Sets the Automatic Protection Switch Revertive mode for the Fiber Group. Access: Offline. AC INI-Param: SDHFbrGrp_APS_RevertMode |
| U32 acSonetSDHFbrGrpAPSWaitToRestoreTime | 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.6 | Unsigned32 | read-write | Sets the APS Wait-to-restore time for the Fiber Group. Access: Offline. AC INI-Param: SDHFbrGrp_APS_WTR |
| INT acSonetSDHFbrGrpKlmNumberingScheme | 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.3 | INTEGER | read-write | Provides VC/VT numbering scheme for STM-1/OC3 fiber group. Access: Offline. AC INI-Param: SDHFbrGrp_KLM_Numbering_Scheme |
| INT acSonetSDHFbrGrpMappingType | 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.2 | INTEGER | read-write | Selects SDH/SONET mapping type (signal label + payload mapping type) for the PSTN interface. Generally per Fiber Group. Single Fiber Group supported in the PSTN interface of TP6310 and TP12610. Applicable only to the TP-6310 and TP-12610. Relevant only when acSysTDMBusType = acFRAMERS (2). 0 = Asynchronous VT1.5 and DS1 1 = Asynchronous TU12 and E1 3 = Asynchronous mapping of DS3 in STS1, DS3 channelized to DS1s 15 = Undefined Should be in coordination with other parameters as follows: - sonetMediumType - acTrunkProtocolType. Access: Offline. AC INI-Param: SDHFbrGrp_Mapping_Type |
| U32 acSonetSDHIndex | 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.1 | Unsigned32 | not-accessible | Fiber groupe index. AC INI-Param: N/A |
| acSonetSDHTable | 1.3.6.1.4.1.5003.9.10.9.1.5.1 | not-accessible | ||
| acTrunk | 1.3.6.1.4.1.5003.9.10.9.1.1.1 | |||
| INT acTrunkAdministrativeState | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.2 | INTEGER | read-write | Trunk Administrative State. Access: Online. AC INI-Param: N/A |
| U32 acTrunkAutoClockPriority | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.10 | Unsigned32 | read-write | Defines the trunk priority for auto-clock fallback (Priority range: 0 - 100 (0 - 99 are priority settings, in which 0 = highest Priority and is the default setting 100 = Do not choose this trunk). Access: Online. AC INI-Param: AutoClockTrunkPriority |
| acTrunkCAS | 1.3.6.1.4.1.5003.9.10.9.1.1.4 | |||
| acTrunkCASEntry | 1.3.6.1.4.1.5003.9.10.9.1.1.4.1.1 | not-accessible | ||
| acTrunkCASTable | 1.3.6.1.4.1.5003.9.10.9.1.1.4.1 | not-accessible | ||
| STR acTrunkCASTablePerChannel | 1.3.6.1.4.1.5003.9.10.9.1.1.4.1.1.2 | SnmpAdminString | read-write | Sets the Cas protocol table index per channel. User need to set each channel the table number 0-7, with comma saperator between channels: '1,3,1,3,1,3..'. Access: Online. AC INI-Param: CasChannelIndex |
| U32 acTrunkCASTablesIndex | 1.3.6.1.4.1.5003.9.10.9.1.1.4.1.1.1 | Unsigned32 | read-write | This parameter determines which CAS protocol file to use on a specific trunk. The index value corresponds to the number configured for the parameter CASFileName_X. Range = not greater than the parameter defining the PSTN CAS Table Num. Access: Online. AC INI-Param: CASTABLEINDEX |
| INT acTrunkClockMaster | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.4 | INTEGER | read-write | Used to select the trunk clock source. 0 = acCLOCK_MASTER_OFF (clock recovered from the line) 1 = acCLOCK_MASTER_ON (the trunk clock source is provided by the internal/TDM bus clock source depending on the parameter TDM Bus Clock Source). Access: Online. AC INI-Param: CLOCKMASTER |
| acTrunkConfig | 1.3.6.1.4.1.5003.9.10.9.1.1 | |||
| INT acTrunkDeactivate | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.11 | INTEGER | read-write | Deactivating a trunk forces AIS alarm on that trunk. Deactivation is used for trunk maintenance without locking the trunk. Activating the trunk will stop the alarm on the trunk. notAvailable(0) appears when the trunk is locked. The trunk can't be SET to this state. Access: Online. AC INI-Param: N/A |
| STR acTrunkDialPlanName | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.8 | SnmpAdminString | read-write | Sets the Dial Plan name that will be used on the specific trunk. Range = string 11 characters. Access: Instant. AC INI-Param: CasTrunkDialPlanName |
| acTrunkEntry | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1 | not-accessible | ||
| INT acTrunkFramingMethod | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.5 | INTEGER | read-write | Selects the Framing method to be used for this trunk. Access: Online. AC INI-Param: N/A |
| acTrunkGlobal | 1.3.6.1.4.1.5003.9.10.9.1.1.8 | |||
| INT acTrunkGlobalLifeLineType | 1.3.6.1.4.1.5003.9.10.9.1.1.8.1 | INTEGER | read-write | This parameter is used to define the type of trunk lifeline. Short trunks 1-2, 3-4. 0 = Activate lifeline on power down 1 = Activate lifeline on power down or on detection of LAN disconnect 2 = Activate lifeline on power down or on detection of LAN disconnect or loss of ping. Access: Offline. AC INI-Param: TrunkLifeLineType |
| U32 acTrunkIndex | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.1 | Unsigned32 | read-only | Trunk ID at board in which the call is taking place. AC INI-Param: N/A |
| acTrunkISDN | 1.3.6.1.4.1.5003.9.10.9.1.1.3 | |||
| acTrunkISDNCommon | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1 | |||
| INT acTrunkISDNCommonBRILayer2Mode | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.8 | INTEGER | read-write | Indicates point to point or point to Multipoint mode for layer2. Applicable in BRI trunks only. One of the following values: Point to point = 0 Point to Multipoint = 1 . Access: Online. AC INI-Param: BriLayer2Mode |
| U32 acTrunkISDNCommonDuplicateQ931BuffMode | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.7 | Unsigned32 | read-write | Activates / de-activates delivery of raw Q.931 messages. Refer to the VoPLib documentation ('ISDN Flexible Behavior'). Access: Online. AC INI-Param: ISDNDUPLICATEQ931BUFFMODE |
| acTrunkISDNCommonEntry | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1 | not-accessible | ||
| U32 acTrunkISDNCommonGeneralCCBehavior | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.5 | Unsigned32 | read-write | This is the bit-field used to determine several general ISDN behavior options. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740. Access: Online. AC INI-Param: ISDNGENERALCCBEHAVIOR |
| U32 acTrunkISDNCommonIncomingCallsBehavior | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.3 | Unsigned32 | read-write | This is the bit-field used to determine several behavior options that influence how the ISDN Stack INCOMING calls behave. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740. Access: Online. AC INI-Param: ISDNINCALLSBEHAVIOR |
| I32 acTrunkISDNCommonIuaInterfaceId | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.6 | Integer32 | read-only | Defines the IUA trunk interface ID value - unsigned integer - in RFC 3057 - SIGTRAN. Default = 0xFFFFFFFF. AC INI-Param: N/A |
| U32 acTrunkISDNCommonOutgoingCallsBehavior | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.4 | Unsigned32 | read-write | This is the bit-field used to determine several behavior options that influence how the ISDN Stack OUTGOING calls behave. Refer to Appendix A.8 in the 'VoPLib Reference Library User's Manual. Access: Online. AC INI-Param: ISDNOUTCALLSBEHAVIOR |
| I32 acTrunkISDNCommonQ931LayerResponseBehavior | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.2 | Integer32 | read-write | Bit-field used to determine several behavior options, which influence how the Q.931 protocol behaves. Access: Online. AC INI-Param: ISDNIBEHAVIOR |
| acTrunkISDNCommonTable | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1 | not-accessible | ||
| INT acTrunkISDNCommonTerminationSide | 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.1 | INTEGER | read-write | Used to set the ISDN Termination to either User or Network. Termination = For ISDN only. User side = 0 Network side = 1. Access: Online. AC INI-Param: TERMINATIONSIDE |
| acTrunkISDNDpnss | 1.3.6.1.4.1.5003.9.10.9.1.1.3.3 | |||
| U32 acTrunkISDNDpnssBehavior | 1.3.6.1.4.1.5003.9.10.9.1.1.3.3.1.1.1 | Unsigned32 | read-write | The DPNSSBehaviour parameter represents a Bit field parameter. Each bit represents a specific type of DPNSS behavior. Currently only the first 2 bits are in use. - DPNSS_BEHAV_STOP_SABMR_AFTER_NL_AND_NT1 bit: (bit #0, bit mask 0x0001) When set to 1: DPNSS stops repeating SABMR after NL and NT1 limits are exceeded. When set to 0: DPNSS continues repeating SABMR after NL and NT1 limits are exceeded. Default is 0 (continue repeating SABMR) - DPNSS_BEHAV_FULL_STARTUP_SUCCESS bit: (bit #1, bit mask 0x0002) When set to 1: the Startup Procedure is considered as a SUCCESS only when ALL DLCs succeeded to Reset When set to 0: the Startup Procedure is considered as a SUCCESS as soon as 1 DLC succeeded to Reset Default is 0: (only partial reset is considered as a success). . Access: Online. AC INI-Param: DPNSSBehavior |
| acTrunkISDNDpnssEntry | 1.3.6.1.4.1.5003.9.10.9.1.1.3.3.1.1 | not-accessible | ||
| U32 acTrunkISDNDpnssNumRealChannels | 1.3.6.1.4.1.5003.9.10.9.1.1.3.3.1.1.2 | Unsigned32 | read-write | This parameter is relevant only to protocol ISDN DPNSS. Defines the number of real channels. Default value is 30. Valid range 1 to 30. Access: Online. AC INI-Param: DPNSSNumRealChannels |
| U32 acTrunkISDNDpnssNumVirtualChannels | 1.3.6.1.4.1.5003.9.10.9.1.1.3.3.1.1.3 | Unsigned32 | read-write | This parameter is relevant only to protocol ISDN DPNSS. Defines the number of virtual channels. Default value is 30. Valid range 0 to 30. Access: Online. AC INI-Param: DPNSSNumVirtualChannels |
| acTrunkISDNDpnssTable | 1.3.6.1.4.1.5003.9.10.9.1.1.3.3.1 | not-accessible | ||
| acTrunkISDNNfas | 1.3.6.1.4.1.5003.9.10.9.1.1.3.2 | |||
| INT acTrunkISDNNfasDchConfig | 1.3.6.1.4.1.5003.9.10.9.1.1.3.2.1.1.1 | INTEGER | read-write | Defines D-channel configuration. This setting is only applicable to ISDN PRI protocols that support NFAS and/or D-channel backup procedures. 0 = D-channel is Primary 1 = Backup 2 = NFAS. Access: Online. AC INI-Param: DCHCONFIG |
| acTrunkISDNNfasEntry | 1.3.6.1.4.1.5003.9.10.9.1.1.3.2.1.1 | not-accessible | ||
| U32 acTrunkISDNNfasGroupNumber | 1.3.6.1.4.1.5003.9.10.9.1.1.3.2.1.1.3 | Unsigned32 | read-write | Relevant only for T1 ISDN NFAS trunks indicates the group number of the NFAS group. ;Valid NFAS group numbers are only 1 to 9, 0 indicating that this trunk is not NFAS (in this case the ISDNNFASInterfaceID and DchConfig parameters are ignored). Access: Online. AC INI-Param: NFASGROUPNUMBER |
| U32 acTrunkISDNNfasInterfaceId | 1.3.6.1.4.1.5003.9.10.9.1.1.3.2.1.1.2 | Unsigned32 | read-write | Defines the Interface ID. Works with NS_EXPLICIT_INTERFACE_ID. Refer to the VoPLib documentation(ISDN Flexible Behavior). Default = (unsigned char)-1. Range = 0 to 255. Access: Online. AC INI-Param: ISDNNFASINTERFACEID |
| acTrunkISDNNfasTable | 1.3.6.1.4.1.5003.9.10.9.1.1.3.2.1 | not-accessible | ||
| acTrunkLine | 1.3.6.1.4.1.5003.9.10.9.1.1.2 | |||
| INT acTrunkLineBuildOutLoss | 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1.1 | INTEGER | read-write | Used to select the line build out loss to be used for this trunk. 0 = 0 dB 1 = 7.5 dB 2 = 15 dB 3 = 22.5 dB. Access: Online. AC INI-Param: LINEBUILDOUT.LOSS |
| INT acTrunkLineBuildOutOverwrite | 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1.2 | INTEGER | read-write | Used to overwrite the Framer's XPM registers values (these registers control the line pulse shape). 0 = No overwrite 1 = Overwrite. Access: Online. AC INI-Param: LINEBUILDOUT.OVERWRITE |
| U32 acTrunkLineBuildOutXPM0 | 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1.3 | Unsigned32 | read-write | Used to control the Framer's XPM0 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1. Should be used only by expert users. Range = 0 to 255. Access: Online. AC INI-Param: LINEBUILDOUT.XPM0 |
| U32 acTrunkLineBuildOutXPM1 | 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1.4 | Unsigned32 | read-write | Used to control the Framer's XPM1 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1. Should be used only by expert users. Range = 0 to 255. Access: Online. AC INI-Param: LINEBUILDOUT.XPM1 |
| U32 acTrunkLineBuildOutXPM2 | 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1.5 | Unsigned32 | read-write | Used to control the Framer's XPM2 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1. Should be used only by expert users. Range = 0 to 255. Access: Online. AC INI-Param: LINEBUILDOUT.XPM2 |
| INT acTrunkLineCode | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.6 | INTEGER | read-write | Use to select line code. B8ZS or AMI for T1 spans and HDB3 or AMI for E1 spans. 0 = Use B8ZS line code (for T1 trunks only = default) 1 = Use AMI line code (for T1 or E1 trunks) 2 = Use HDB3 line code (for E1 trunks only). Access: Online. AC INI-Param: LINECODE |
| acTrunkLineEntry | 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1 | not-accessible | ||
| acTrunkLineTable | 1.3.6.1.4.1.5003.9.10.9.1.1.2.1 | not-accessible | ||
| INT acTrunkLineType | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.9 | INTEGER | read-only | Line type. lineTypeBRI(12) - If the physical type is BRI. lineTypeE1(10)/lineTypeT1(11) - For non BRI IF when there are other lines that are already configured to either E1 or T1. lineTypeUnknown(-1) - For non BRI IF when no lines are configured. AC INI-Param: N/A |
| INT acTrunkProtocolType | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.3 | INTEGER | read-write | Used to set the PSTN protocol to be used for this trunk. Relevant only when TDMBusType=acFRAMERS (2). Either: NONE = 0 E1_EURO_ISDN = 1 T1_CAS = 2 T1_RAW_CAS = 3 T1_TRANSPARENT = 4 E1_TRANSPARENT_31 = 5 E1_TRANSPARENT_30 = 6 E1_MFCR2 = 7 E1_CAS = 8 E1_RAW_CAS = 9 T1_NI2_ISDN = 10 T1_4ESS_ISDN = 11 T1_5ESS_9_ISDN = 12 T1_5ESS_10_ISDN = 13 T1_DMS100_ISDN = 14 J1_TRANSPARENT = 15 T1_NTT_ISDN = 16 E1_AUSTEL_ISDN = 17 E1_HKT_ISDN = 18 E1_KOR_ISDN = 19 T1_HKT_ISDN = 20 E1_QSIG = 21 E1_TNZ_ISDN = 22 T1_QSIG = 23 T1_IUA = 28 E1_IUA = 29 E1_FRENCH_VN6_ISDN = 30 E1_FRENCH_VN3_ISDN = 31 T1_EURO_ISDN = 34 T1_DMS100_MERIDIAN_ISDN = 35 T1_NI1_ISDN = 36 E1_DUA = 37 E1_Q931_PACKETS = 38 T1_Q931_PACKETS = 39 E1_NI2_ISDN = 40 E1-CAS-R15 = 41 V5 = 43 BRI-EURO-ISDN = 50 BRI-NI-2 = 51 BRI-DMS100 = 52 BRI-5ESS = 53 BRI-QSIG = 54 BRI-VNG = 55 BRI-NTT = 56 BRI-IUA = 57. . Access: Online. AC INI-Param: PROTOCOLTYPE |
| acTrunkStatus | 1.3.6.1.4.1.5003.9.10.9.2.1 | |||
| INT acTrunkStatusAlarm | 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.7 | INTEGER | read-only | Describes the trunk's alarm status. 1 - Disabled. 2 - Active - OK. 3 - LOS/LOF Alarm. 4 - AIS Alarm. 5 - RAI Alram. 6 - D-Channel Alarm. 7 - Lower Layer Down. AC INI-Param: N/A |
| OCT acTrunkStatusChannels | 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.3 | OCTET STRING | read-only | Reperesents Trunk's Channels-Status. Each nibble (half Byte) presents one channel status, as following: 1 - invalid B-Channel. 2 - None. 3 - Open. 4 - Media. 5 - SS7. 6 - HDLC. 7 - DPNSS. 8 - CAS. AC INI-Param: N/A |
| INT acTrunkStatusDChannel | 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.6 | INTEGER | read-only | Describes the trunk's D channel status. 0 - dChannelEstablished 1 - dChannelNotEstablished 10 - dChannelNotApplicable. AC INI-Param: N/A |
| acTrunkStatusEntry | 1.3.6.1.4.1.5003.9.10.9.2.1.1.1 | not-accessible | ||
| INT acTrunkStatusLedStatusColor | 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.1 | INTEGER | read-only | Trunk led status color. AC INI-Param: N/A |
| INT acTrunkStatusLedStatusState | 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.2 | INTEGER | read-only | Trunk led status blinking rate. AC INI-Param: N/A |
| acTrunkStatusTable | 1.3.6.1.4.1.5003.9.10.9.2.1.1 | not-accessible | ||
| I32 acTrunkStatusV5InterfaceNum | 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.4 | Integer32 | read-only | V5.2 interface containing this trunk. -1 means information not available or not relevant. AC INI-Param: N/A |
| I32 acTrunkStatusV5LinkID | 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.5 | Integer32 | read-only | V5.2 link containing this trunk. -1 means information not available or not relevant. AC INI-Param: N/A |
| acTrunkTable | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1 | not-accessible | ||
| INT acTrunkTraceLevel | 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.7 | INTEGER | read-write | Defines the Trace level: acNO_TRACE = 0 acFULL_ISDN_TRACE = 1 acLAYER3_ISDN_TRACE = 2 acONLY_ISDN_Q931_MSGS_TRACE = 3 acLAYER3_ISDN_TRACE_NO_DUPLICATION = 4 acFULL_ISDN_TRACE_WITH_DUPLICATION = 5 acISDN_Q931_RAW_DATA_TRACE = 6 acISDN_Q921_RAW_DATA_TRACE = 7 acISDN_Q931_Q921_RAW_DATA_TRACE = 8 acSS7_MTP2 = 10 acSS7_MTP2_AND_APPLI = 11 acSS7_MTP2_SL_L3_NO_MSU = 12 acSS7_AAL = 15. Access: Online. AC INI-Param: TRACELEVEL |
| acTrunkV5 | 1.3.6.1.4.1.5003.9.10.9.1.1.5 | |||
| acTrunkV5Entry | 1.3.6.1.4.1.5003.9.10.9.1.1.5.1.1 | not-accessible | ||
| U32 acTrunkV5NumberOfCChannels | 1.3.6.1.4.1.5003.9.10.9.1.1.5.1.1.1 | Unsigned32 | read-write | Indicates the number of timeslots used as communication channels in a V5 trunk. 0 - No C-channel, the trunk is voice only. 1 - Timeslot 16 is used for the V5 signaling . Access: Online. AC INI-Param: V5NumberOfCChannels |
| INT acTrunkV5ProtocolSide | 1.3.6.1.4.1.5003.9.10.9.1.1.5.1.1.2 | INTEGER | read-write | Indicates the V5 side of the V5 protocol served by the trunk.. 0 - AN side. 1 - LE side . Access: Online. AC INI-Param: V5ProtocolSide |
| acTrunkV5Table | 1.3.6.1.4.1.5003.9.10.9.1.1.5.1 | not-accessible |
RFC description
AudioCodes PSTN trunk configuration and management for voice gateway devices.
Start monitoring AudioCodes Mediant-series gateways with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.